Home

Foreword - Nissan Extended Warranty

1. Overdrive switch Each time your vehicle is started the transmis sion is automatically reset to overdrive ON ON For normal driving the overdrive switch is engaged The transmission is up shifted into overdrive as the vehicle speed increases The overdrive does not engage until the engine has warmed up OFF Changed for driving up and down long slopes where engine braking would be advantageous push the overdrive switch The O D OFF light illuminates When cruising at a low speed or climb ing a gentle slope you may feel uncom fortable shift shocks as the transmission shifts between third and overdrive re peatedly In this case press the over drive switch The O D OFF indicator light comes on at this time When driving conditions change press the overdrive switch again The O D OFF indicator light goes out Remember not to drive at high speeds for extended periods of time with the O D OFF light illuminated This reduces the fuel economy Fail safe When the fail safe operation occurs the next time the key is turned to the ON position the O D OFF light will blink for approximately 8 seconds after coming on for 2 seconds While the vehicle can be driven under these circum stances please note that the automatic trans mission will be locked in third gear If the vehicle is driven under extreme con ditions such as excessive wheel spinning and subsequent hard braking the fail safe system may be activate
2. Tray PULL to remove P PUSH to open i 1C1243 TRAYS WARNING The storage tray should not be used while driving so full attention may be given to vehicle operation Instruments and controls 2 23 SIC1238 GLASSES CASE The glasses case can be opened by pushing the button WARNING The glasses case should not be used while driving so full attention may be given to vehicle operation 2 24 Instruments and controls CAUTION Do not use for anything other than glasses Do not leave glasses in the glasses case while parking in direct sunlight The heat may damage the glasses to remove the inside tray Se SIC1279A CUP HOLDER WARNING The cup holder should not be used while driving so full attention may be given to vehicle operation For larger cups remove the inside tray Rear ERT OPEN SPA0388 AA CAUTION e Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink If the liquid is hot it can scald you or your pas senger e Use only soft cups in the cup holder Hard objects can injure you in an accident GLOVE BOX When locking or unlocking the glove box use the master key The glove box may be opened by pulling the handle WARNING Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop Instruments and co
3. 2 Move the lever at the front of the hood e Make sure the hood is completely with your fingertips and raise the hood closed and latched before driving 3 When closing the hood slowly close the Failure to do so could cause the hood hood and make sure it locks into place to fly open and result in an accident e If you see steam or smoke coming from the engine compartment to avoid injury do not open the hood 3 8 Pre driving checks and adjustments TRUNK LID WARNING e Do not drive with the trunk lid open This could allow dangerous exhaust gases to be drawn into the vehicle See Precautions when starting and driving in the 5 Starting and driv ing section for exhaust gas e Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously injured Keep the car locked with the trunk closed when not in use and prevent children s access to car keys SPA0985 OPENER OPERATION The trunk lid release button is located under the driver s arm rest To open the trunk lid pull the release handle To close push the trunk lid down securely E CANCEL SPA0095 Cancel lever When the lever is in the cancel position the trunk lid cannot be opened with the trunk lid release button It can be opened only with the key Pre driving checks and adjustments 3 9 FUEL FILLER LID P T PU
4. Do not put anything on the seat which insulates heat such as a blanket cushion seat cover etc Otherwise the seat may become overheated Do not place anything hard or heavy on the seat or pierce it with a pin or similar object This may result in damage to the heater e Any liquid spilled on the heated seat should be removed immediately with a dry cloth When cleaning the seat never use gasoline thinner or any similar ma terials If any abnormalities are found or the heated seat does not operate turn the switch off and have the system checked by your NISSAN dealer Instruments and controls 2 21 TRACTION CONTROL SYSTEM TCS CANCEL SWITCH if so equipped TCS OFF SIC1065 POWER OUTLET Front Rear PULL to remove PULL to open 1C1237 To cancel the Traction Control System TCS push the TCS cancel switch The indicator ore will come on Push it again to turn the system back on See Traction control system in the 5 Start ing and driving section 2 22 Instruments and controls The power outlet is for powering electrical accessories such as cellular telephones AA CAUTION e Use caution as the socket and plug may be hot during or immediately after use e This power outlet is not designed for use with a cigarette lighter unit e Do not use with accessories that ex ceed a 12 volt 120W 10A power draw Do not use double adapters or more than one
5. 1 36 Seats restraints and supplemental air bag systems ing a child restraint Failure to use the retractor s locking mode will result in the child restraint not being properly secured The child restraint could tip over or otherwise be unsecured and cause injury to the child in a sudden stop or collision 7 Front facing Front INSERT to fasten Move seat fully back I Pull to engage automatic locking mode SS0135 SSS0055 SSS0113 Front facing 2 Route the seat belt tongue through the child 3 Pull on the shoulder belt until all of the belt ets restraint and insert it into the buckle until is fully extended At this time the belt If you must install a child restraint in the front you hear and feel the latch engage Be sure retractor is in the automatic locking mode seat follow these steps to follow the child restraint manufacturer s child restraint mode It reverts back to 1 Position the child restraint on the front instructions for belt routing emergency locking mode when the belt is passenger seat It should be placed in a fully retracted front facing direction only Move the seat to the rearmost position Always follow the child restraint manufacturer s instructions Child restraints for infants must be used in the rear facing direction and therefore must not be used in the front seat Seats restraints and supplemental air bag systems 1 37 Fronttaci
6. ASD KKS an T11009 A 0 8409 x 43 11 21 36 x 1 095 Technical and consumer information 10 7 The spark ignition system of this vehicle meets all requirements of the Canadian Interference Causing Equipment Regula tions 10 8 Technical and consumer information TIRES AND WHEELS Steel 15 x 6JJ Road wheel 16 x 6 5JJ 17 x 7JJ option P205 65R15 92H P215 55R16 91H Aluminum Conventional Tire Conventional 1 7125 70D16 2 T125 90D16 2 3 T135 90D16 2 4 Spare 1 For CANADA 2 For US 3 For models with Viscous LSD 4 For models equipped with 17 size tire option P225 50R17 93V option DIMENSIONS AND WEIGHTS Overall length Overall width Overall height Front tread Rear tread Wheelbase Gross vehicle weight rating Gross axle weight rating Front Rear Sedan in mm 190 4 4 838 in mm 70 3 1 785 in mm 56 5 1 435 in mm 60 2 1 530 1 59 8 1 520 2 in mm 59 4 1 510 1 59 1 1 500 2 in mm 108 3 2 750 lb kg See the F M V S S certifica tion label on the driver s side lb kg lock pillar lb kg 1 For models with road wheel size 15 x 6JJ 16 x 6 5JJ 2 For models with aluminum wheel size 17 x 7JJ Technical and consumer information 10 9 WHEN TRAVELING OR REGISTERING YOUR VEHICLE IN ANOTHER COUNTRY When planning to travel in another country you should first find out if the fuel available is su
7. Automatic transmission model SCE0199 AA CAUTION e Never tow an automatic transmission models with the front wheels on the ground as this may cause serious and expensive damage to the trans mission If it is necessary to tow the vehicle with the rear wheels raised always use a towing dollies under the front wheels e Never tow an automatic transmission model from the rear that is back ward with four wheels on the ground as this may cause serious and expen sive damage to the transmission VEHICLE RECOVERY Freeing a stuck vehicle e Towchains or cables must be attached only to the main structural members of the ve hicle e Pulling devices should be routed so they do not touch any part of the suspension steer ing brake or cooling systems e Always pull the cable straight out from the front or rear of the vehicle Never pull on the vehicle at an angle e Pulling devices such as ropes or canvas straps are not recommended for use in vehicle towing or recovery e Stand clear of an stuck vehicle WARNING Do not spin your tires at high speed This could cause them to explode and result in serious injury Parts of your vehicle could also overheat and be dam aged In case of emergency 6 13 MEMO 6 14 In case of emergency 7 Appearance and care Cleaning OxtenOF irinin ra 7 2 WaShINGscsesci otc ic deskediieets ni aneeds hae edti ake 7 2 Waxing REMOVING SPOtS crisissen UNGOS
8. Headlight fog light if so equipped and turn signal switch P 2 17 Fuse box cover P 8 23 Outside mirror remote control P 3 13 Driver supplemental air bag P 1 8 Tilting steering wheel lock lever P 3 12 Glove box P 2 25 Cruise control set switch P 5 14 Ignition switch steering lock P 5 4 f Tray P 2 23 or ashtray accessory P 2 23 Power outlet P 2 22 or cigarette lighter accessory P 2 23 Hazard warning flasher switch P 2 20 See the page indicated in parentheses for operating details SIC1225 2 2 Instruments and controls METERS AND GAUGES Wanrning Indicator lights Speedometer f Tachometer Engine coolant temperature gauge Fuel gauge x1000r min Odometer Reset knob Warning Indicator lights Total Trip for trip odometer Warning Indicator fights 1C1321 Instruments and controls 2 3 J Reset knob Odometer Twin trip odometer SIC1227 SPEEDOMETER AND ODOMETER Speedometer The speedometer indicates vehicle speed Odometer Twin trip odometer The odometer twin trip odometer are displayed when the ignition key is in the ON position The odometer records the total distance the vehicle has been driven The twin trip odometer records the distance of individual trips 2 4 Instruments and controls Changing the display Pushing the reset knob changes the display as follows TRIP A TRIP B gt TRIP A Resetting the trip odometer Pushing
9. If you believe that your vehicle has a defect which could cause a crash or could cause injury or death you should immediately inform the National High way Traffic Safety Administration NHTSA in addition to notifying NISSAN f NHTSA receives similar complaints it may open an investigation and if it finds that a safety defect exists in a group of vehicles it may order a recall and remedy campaign However NHTSA cannot become involved in individual problems between you your dealer or NISSAN To contact NHTSA you may either call the Auto Safety Hotline toll free at 1 800 424 9393 or 366 0123 in Wash ington D C area or write to NHTSA U S Department of Transportation Washington D C 20590 You can also obtain other information about motor vehicle safety from the Hotline You may notify NISSAN by contacting our Consumer Affairs Department toll free at 1 800 NISSAN 1 In Hawaii call 808 836 0888 READINESS FOR INSPECTION MAINTENANCE I M TEST US only Due to legal requirements in some states areas your vehicle may be required to be in what is called the ready condition for an Inspection Maintenance I M test of the emis sion control system The vehicle is set to the ready condition when it is driven through certain driving patterns Usually the ready condition can be obtained by ordinary usage of the vehicle If a powertrain system component is repaired or the battery is disconnected the veh
10. It reverts back to emergency locking mode when the belt is fully retracted Seats restraints and supplemental air bag systems 1 33 PULL to tighten Rear facing V amp gf er WS A Front oe fast Rego Check for a secure fit 3 SS0110 4 Allow the belt to retract Pull up on the belt to remove any slack in the belt Before placing the child in the child re straint use force to tilt the child restraint from side to side and tug it forward to make sure that it is securely held in place Check that the retractor is in the automatic locking mode by trying to pull more belt out of the retractor If you cannot pull any more belt webbing out of the retractor the belt is in the automatic locking mode Check to make sure that the child restraint is properly secured prior to each use If the belt is not locked repeat steps 3 through 6 After the child restraint is removed and the seat belt is allowed to wind back into the 1 34 Seats restraints and supplemental air bag systems retractor the automatic locking mode child restraint mode is canceled the seat belt only locks during a sudden stop or impact Anchor point TOP TETHER STRAP CHILD RESTRAINT if so equipped If your child restraint has a top tether strap it must be secured to the provided anchor point First secure the child restraint with the lap portion of the rear seat belt Remove the a
11. cee 10 5 Outside mirror 3 13 Outside mirror control 3 13 Outside mirrors Overdrive switch Overheat If your vehicle overheats 6 10 P Parking Brake CheCKissiossiissiinseiseic asies 8 20 Parking brake Check 0 c cccseseeeeee 5 13 Parking brake operation 00c ce 5 13 Parking on Mil Sene 5 13 Parking parking on hills 0 0 5 17 Periodic maintenance schedules 0 00 9 5 Personal light sccccesccecteteartaccracsr enue 2 31 Power Front seat adjustment c eeeeseeereeeeeee 1 4 Power door l0Ck iiinis 3 2 Power steering fluid 0 c cece 8 11 Power steering system 5 18 Power windows 0 2 27 Pre tensioner seat belt system 1 17 Precautions Braking precautions ncnian 5 18 Cruise control precautions 5 13 Maintenance precautions ceeeeeeee 8 2 On child restraints On seat belt USaQe cece eee 1 20 On supplemental restraint system 1 8 Precautions when starting and driving 5 2 Pushstartinhg aerei runean 6 9 R Radio car phone or CB radio 4 25 Readiness for inspection maintenance I M test USA ODIY sadeiccscsccteacscescecesssssevscersustsentcasivases 10 21 Rear door lock Child safety rear door lock 3 4 Rear seat adjustment eceeseeseeeeeereeeeeeee 1 6 Rear window and outside mirror defogger SWIC cevvetee Gee ere aud eee ere 2 16 Registering your vehicle in anot
12. ecceceeeeeees 10 3 Ga GC yatsa 2 5 FUSE Siasa 8 21 Fusible lks neioii tipii 8 22 G Garage door opener Integrated HomeLink Universal Transceiver escceseeceereeeeeeaee 2 33 G s CaP aundi 3 10 Gauge 2 3 Engine coolant temperature gauge 2 5 F gl gaVe nearne 2 5 1 Tole 141 1 eee eer prceeterre tree rer EE 2 4 Speedometer 2 4 Tachometer we 2 4 General maintenance 9 2 9 3 Glasses CaSe wien rime a ns 2 24 GIOVE DOK Niraes iiianoe s 2 25 Glove OX OCK ss ssc ccc cheats heteeneet ees 2 25 H Hazard warning flasher switch Head restraints 0 ceee Headlamps Bulb replacement Headlights Bulb replacement Headlights Headlight switch 0 2 17 Heated Seats tii ccisccseysietidieesetesah veces ceesiieens 2 21 Heater Engine coolant heater 0 cee 5 22 Heater and air conditioner controls 4 3 Heater operation c cceeeeeeseeeeeeees 4 3 Operation Semiautomatic air conditioner 4 4 HomeLink Universal Transceiver 2 33 l Ignition SWito hies iirst ds 5 4 Automatic transmission models 0 5 4 Key POSITIONS iyice Manual transmission models Immobilizer system eeec eee eeeeeeneeee Indicator lights and chimes See warning indicator lights and chimes INSid MirrOF eee eee ae Inspection maintenance I M test 10 20 instrument p nels senesnis 2 2 Integrated HomeLink
13. seat belt need servicing e The supplemental air bag warning light remains on after approximately 7 seconds e The supplemental air bag warning light flashes intermittently e The supplemental air bag warning light does not come on at all Under these conditions the supplemental front air bags supplemental side air bags and or pre tensioner seat belt may not operate prop erly They must be checked and repaired Take your vehicle to the nearest authorized NISSAN dealer AA WARNING If the supplemental air bag warning light is on it could mean that the supplemen tal front air bag system supplemental side air bag system and or pre tensioner seat belt will not operate in an accident Repair and replacement procedure The supplemental front air bags supplemental side air bags and pre tensioner seat belt are designed to inflate on a one time only basis As a reminder unless it is damaged the supplemental air bag warning light will remain illuminated after inflation has occurred Repair and replacement of these systems should be done only by authorized NISSAN dealers To ensure long term functioning these systems must be inspected 10 years after the date of manufacture noted on the cer tification label located on the driver side center pillar When maintenance work is required on the vehicle the supplemental front air bags supplemental side air bags related parts and pre tensioner seat belt should be pointed out
14. 2 Replace the battery with a new one Recommended battery Sanyo CR2025 or equivalent Make sure that the side faces the bottom case 3 Close the lid securely 4 Push the remote controller button two or three times to check its operation See your NISSAN dealer if you need any assistance for replacement If the battery is removed for any reason other than replacement perform step 4 above e Be careful not to touch a circuit board and a battery terminal e An improperly disposed battery can harm the environment Always confirm local regulations for battery disposal e The remote controller is water resistant however if it does get wet immediately wipe completely dry e When changing batteries do not let dust or oil get on the controller FCC Notice Changes or modifications not expressly approved by the manufacturer compliance Pre driving checks and adjustments 3 7 HOOD could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules and RSS 210 of Industry Canada Operation is subject to the following two conditions 1 This de vice may not cause harmful interference and 2 this device must accept any inter ference received including interference that may cause undesired operation of the device SPA0984 1 Pull the hood lock release handle 4 lo cated below the instrument panel the hood A WARNING will then spring up slightly
15. 4 12 AM FM radio with cassette player and compact CISC PlAYOl ernea 4 12 AM FM radio with compact disc player 4 12 Ambient temperature switch AMB Air COMGITION GB ker eei areren EEEE EER 4 11 Anchor point locations Top tether strap 1 35 Antenna Manual is ccso sta ciaey ccaeeciavieca navies 4 24 POWER soccer ree ener eerienes 4 24 Anti lock Brake System ABS cee 5 19 Anti lock brake warning light 0 000 2 9 Appearance care Exterior appearance Care 7 2 Interior appearance Care uu 7 4 AMES ccs ivecces chen E 1 8 UGIONSYSTOMM ty titers ct cian better eats Los 4 12 Automatic Automatic transmission fluid ATF 8 10 Driving with automatic transmission 5 8 SUNO iiio ccipcviee si ceteser tncan aumteieees 2 29 Transmission selector lever lock release 5 9 Avoiding collision and rollover s 5 3 B Batterierna eaii 8 13 Battery replacement See multi remote control SYSIOM ennonn ieia erer ititer ariris irii 3 7 Battery Battery saver system 2 18 Before starting the engine ee 5 7 Belts See drive belts cece 8 15 Brake Anti lock brake system ABS 8 5 19 Brake and clutch fluidi 8 12 Brake BOOSTEE is c 5 scc0sceeivieccwiizenscas 8 21 Brake pedal eeccenssctet tes cccti ti etat ec 8 20 Brake pedal CheCk 0 c cccecsesseseeeeeee 8 20 Parking brake check s 5 13 8 20 Parking brake oper
16. Do not work under the hood while the engine is hot Turn off the engine and wait until it cools down Never connect or disconnect either the battery or any transistorized com ponent connector while the ignition key is on Never leave the engine or the auto matic transmission related compo nent harness connector discon nected while the ignition key is on Avoid direct contact with used engine oil Improperly disposed motor oil and or other vehicle fluids can hurt the environment Always conform to local regulations for disposal of ve hicle fluid This 8 Do it yourself section gives instruc tions regarding only those items which are relatively easy for an owner to perform You should be aware that incomplete or im proper servicing may result in operating diffi culties or excessive emissions and could af fect your warranty coverage If in doubt about any servicing have it done by your NISSAN dealer Do it yourself 8 3 ENGINE COMPARTMENT CHECK LOCATIONS Ignition coils spark plugs Automatic transmission fluid dipstick Brake fluid reservoir Engi il fill none OSE RaR Clutch fluid reservoir Manual transmission Power steering fluid reservoir Air cleaner ARS AEN fi rs a By Oe LO A st Lj E A J f me g oa T TAS yes D Kal yD e LLY RY k 7 Engine coolant reservoir Fuse Fusible link holder Windshield washer fluid reservoir Engine oil dipstick Battery Ignition coils spark plugs
17. FRESH REC FRE and RECIRCULATION The indicator will go out The air recirculation button will not be acti vated when the air conditioner is in DEF mode Air flow control Pushing the manual air flow control button selects the air outlet to j Air flows from center and side ventila tors lt 7 Air flows from center and side ventila tors and foot outlets Air flows mainly from foot outlets xy Air flow from defroster and foot out lets To turn system off Push the OFF button AMBIENT TEMPERATURE SWITCH AMB Push the ambient temperature switch The outside ambient temperature will be displayed for approximately 5 seconds The ambient temperature sensor is located in front of the radiator The sensor may be affected by road or engine heat wind direc tion and other driving conditions The dis play may differ from the actual ambient temperature or the temperature displayed on various signs or billboards OPERATING TIPS When the engine coolant temperature and outside air temperature are low the air flow from the foot outlets may not operate for a maximum of 150 seconds However this is not a malfunction After the coolant temperature warms up the air flow from the foot outlets will operate normally Sensor HA1011 The sensor on the instrument panel helps maintain a constant temperature do not put anything on or around this sensor SERVICING AIR CONDITIONER The air condit
18. minimum maintenance requirements with longer service intervals to save you both time and money However some day to day and regular maintenance is essential to maintain your NISSAN s good mechanical condition as well as its emission and engine performance It is the owner s responsibility to make sure that the specified maintenance as well as general maintenance is performed As the vehicle owner you are the only one who can ensure that your vehicle receives the proper maintenance care You are a vital link in the maintenance chain General maintenance General maintenance includes those items which should be checked during normal day to day operation of the vehicle They are es sential if your vehicle is to continue to operate properly It is your responsibility to perform these procedures regularly as prescribed These checks or inspections can be done by yourself a qualified technician or if you prefer your NISSAN dealer Periodic maintenance The maintenance items listed in this part are required to be serviced at regular intervals 9 2 Maintenance However under severe driving conditions ad ditional or more frequent maintenance will be required Where to go for service If maintenance service is required or your vehicle appears to malfunction have the sys tems checked and tuned by an authorized NISSAN dealer NISSAN technicians are well trained special ists and are kept up to date with the l
19. piping and connections for leaks looseness or deteriora tion Replace any parts if they are damaged Engine coolant Drain and flush the cooling system Engine oil amp oil filter Under normal driving 9 10 Maintenance conditions the engine oil and oil filter should be replaced in accordance with the mainte nance schedule However under severe driv ing conditions they may have to be replaced more frequently Spark plugs Replace with new plugs having the correct heat range Intake amp exhaust valve clearance Check the valve clearance if valve noise increases Chassis and body maintenance Brake lines amp cables Check the brake lines and hoses including brake booster vacuum hoses connections amp check valve and park ing brake cables for proper attachment leaks cracks chafing abrasion deterioration etc Brake pads amp rotors Check these and the other neighboring brake components for wear deterioration and leaks Under severe driving conditions they may have to be inspected more frequently Manual transaxle oil amp automatic transaxle fluid Check the fluid level and visually in spect for signs of leakage Under severe driving conditions the oil should be replaced at the specified interval Steering gear amp linkage axle amp suspension parts and front drive shaft boots Check for damage looseness and leakage of oil or grease Under severe driving conditions they may have
20. position 2 Push the button in 3 Turn on the fan control dial 4 Push on the air conditioning button The indicator light will come on 5 Move the temperature control lever to the desired position For quick cooling when the outside tempera ture is high move the air recirculation button to the ON position Be sure to return the air recirculation button to the OFF position for normal cooling Dehumidified heating This mode is used to heat and dehumidify 1 Push the air recirculation button to the OFF position 2 Push the 4 a button in 3 Turn on the fan control dial 4 Push on the air conditioning button The indicator light will come on 5 Move the temperature control lever to the desired position Dehumidified defogging This mode is used to defog the windows and dehumidify 1 Push the lt 7 button in 2 Turn on the fan control dial 3 Push on the air conditioning button The indicator light will come on 4 Move the temperature control lever to the desired position When the y button is pushed the air con ditioner will automatically be turned on to de Heater air conditioner and audio systems 4 5 fog the windshield and the air recirculate mode will automatically be turned off Outside air is drawn into the passenger com partment to improve the defogging perfor mance Operating tips Keep the windows and sun roof closed while the air conditioner is in operation A
21. radio mutes when the select button is pushed 4 When the sound resumes memorizing is complete 5 Other station select buttons can be set in the same manner If the battery cable is disconnected or if the radio fuse opens the radio memory is can celled In that case reset the desired stations Cassette tape player operation Turn the ignition key to ACC or ON then carefully insert a cassette tape into the tape door The cassette tape automatically pulls into the player The word TAPE and moving digital squares illuminate on the right side of the display window CAUTION Do not force the cassette tape into the tape door This could cause player dam age The cassette tape automatically changes di rections to play the other side when the first side is complete At this time the moving digital squares illuminate on the left side of the display window Precaution on cassette player operation e To maintain good quality sound NISSAN recommends using cassette tapes of 60 minutes or shorter in length e Cassette tapes should be removed from the player when not in use Store cas settes in their protective cases and away from direct sunlight heat dust mois ture and magnetic sources e Direct sunlight can cause the cassette to become deformed The use of deformed cassettes may cause the cassette to jam in the player e Do not use cassettes with labels which are peeling and loose If used the label
22. to the person conducting the maintenance The ignition key should always be in the LOCK position when working under the hood or in side the vehicle WARNING e Once the supplemental front air bag supplemental side air bag and or pre Seats restraints and supplemental air bag systems 1 19 SEAT BELTS PRECAUTIONS ON SEAT BELT tensioner seat belt has in flated the USAGE air bag module will not function again and must be replaced The module Your chances of being injured or killed in an should be replaced by an authorized accident and or the severity of injury may be greatly reduced if you are wearing your seat belt and it is properly adjusted NISSAN strongly encourages you and all of your pas sengers to buckle up every time you drive NISSAN dealer The supplemental front air bag module or supplemental side air bag module cannot be re paired even if your seating position includes a supple e The supplemental front air bag sys mental air bag tem supplemental side air bag sys Most states provinces or territories require tem and pre tensioner seat belt that seat belts be worn at all times when a should be inspected by an authorized vehicle is being driven NISSAN dealer if there is any damage to the front end or side portion of the vehicle e If you need to dispose of these supplemental systems or scrap the vehicle contact an authorized NISSAN dealer Correct disposal procedures are set forth in the app
23. AND WHEELS less than 1 mile 1 6 km COLD tire pressures are shown on the tire placard affixed to the with high speed capability tires Driv Max inflation pressure glove box lid ing faster than 85 MPH 140 km h may result in tire failure loss of con A WARNING trol and possible injury DI1033M If you have a flat tire see Flat tire in the 6 In case of emergency section TIRE PRESSURE Maximum inflation pressure Do not exceed the maximum inflation pres sures shown on the side wall of the tire Tire inflation pressure e Improperly inflated tires can fail sud denly and cause an accident e The vehicle capacity weight is indi cated on the tire placard Do not load your vehicle beyond this capacity Overloading your vehicle may result in reduced tire life unsafe operating conditions due to premature tire fail ure or unfavorable handling charac teristics and could also lead to a serious accident Loading beyond the specified capacity may also result in failure of other vehicle components e Before taking a long trip or whenever you have loaded your vehicle heavily use a tire pressure gauge to ensure TYPES OF TIRES CAUTION When changing or replacing tires be sure all four tires are of the same type i e summer all season or snow and construction Your NISSAN dealer may be able to help you with information about tire type size speed rating and availability Replacement t
24. API grade SG SH Energy Conserving amp Il or API grade SJ Energy conserving oil An oil with a single designation SG or SH or in combination with other categories for example SG CC or SG CD may also be used if one with the API certification mark cannot be found An ILSAC grade GF I amp GF II oil can also be used Mineral based or synthetic type oils may be used in your NISSAN vehicle These oils must however meet the API quality and SAE vis cosity ratings specified for your vehicle Do not mix mineral based and synthetic type oils in the engine at the same time Oil additives NISSAN does not recommend the use of oil additives The use of an oil additive is not necessary when the proper oil type is used and maintenance intervals are followed Oil which may contain foreign matter or has been previously used should not be used Oil viscosity The engine oil viscosity or thickness changes with temperature Because of this it is impor tant that the engine oil viscosity be selected based on the temperatures at which the ve hicle will be operated before the next oil change The recommended SAE viscosity number chart shows the recommended oil viscosities for the expected ambient tempera tures Choosing an oil viscosity other than that recommended could cause serious engine damage Selecting the correct oil filter Your new vehicle is equipped with a high quality genuine NISSAN oil filter When replac ing use the
25. ENGINE OIL i Park the vehicle on a level surface and apply the parking brake Run the engine until it reaches operating temperature Turn the engine off and wait more than 10 minutes Place a large drain pan under the drain plug Remove the oil filler cap 6 Remove the drain plug with a wrench and completely drain the oil If oil filter is to be changed remove and replace it at this time See later in Engine oil for changing engine oil filter fA CAUTION Be careful not to burn yourself as the engine oil is hot Waste oil must be disposed of properly Check your local regulations 7 Clean and re install the drain plug and new washer Securely tighten the drain plug with a wrench Drain plug tightening torque 22 to 29 ft lb 29 to 39 N m Do not use excessive force Refill engine with recommended oil and install the cap securely See Capacities and recommended fuel lubricants in the 10 Technical and consumer information section for drain and refill capacity The drain and refill capacity depends on the oil temperature and drain time Use these specifications for reference only Always use the dipstick to determine when the proper amount of oil is in the engine Start the engine Check for leakage around the drain plug Correct as required 10 Turn the engine off and wait more than 10 minutes Check the oil level with the dip stick Add eng
26. In the winter when it is anticipated that the temperature will drop below 32 F 0 C check anti freeze ethylene glycol base to assure proper winter protection For additional infor mation see Engine Cooling System in the 8 Do it yourself section BATTERY If the battery is not fully charged during ex tremely cold weather conditions the battery fluid may freeze and damage the battery To maintain maximum efficiency the battery should be checked regularly For additional information see Battery in the 8 Do it yourself section DRAINING OF COOLANT WATER If the vehicle is to be left outside without anti freeze drain the cooling system by open ing the drain valves located under the radiator and on the engine block Refill before operat ing the vehicle See Engine cooling system in the 8 Do it yourself section for changing engine coolant TIRE EQUIPMENT 1 SUMMER tires are of a tread design to provide superior performance on dry pave ment However the performance of these tires will be substantially reduced in snowy and icy conditions If you operate your vehicle on snowy or icy roads NISSAN recommends the use of MUD amp SNOW or ALL SEASON tires on all four wheels Please consult your NISSAN dealer for the tire type size speed rating and availability information 2 For additional traction on icy roads studded tires may be used However some prov inces and states proh
27. OIL Front N Start the engine and warm it up until the radiator fan operates Then race the engine two or three times under no load Watch the coolant temperature gauge for signs of overheating Stop the engine After it completely cools down refill the radiator up to the filler opening Fill the reservoir tank up to the MAX level Check the radiator drain plug and the drain plug on the engine block for any sign of leakage CHECKING ENGINE OIL LEVEL A Park the vehicle on a level surface and apply parking brake Run the engine until it reaches operating temperature Turn off the engine Wait more than 10 minutes for the oil to drain back into the oil pan Remove the dipstick and wipe it clean Reinsert it all the way Do it yourself 8 7 SDI0534 6 It maintenance Remove the dipstick again and check the oil level It should be between the H and L marks If the oil level is below the L mark remove the oil filler cap and pour recom mended oil through the opening Do not overfill Recheck oil level with dipstick is normal to add some oil between oil intervals or during the break in period depending on the severity of operating conditions 8 8 Do it yourself CAUTION Oil level should be checked regularly Operating with insufficient amount of oil can damage the engine and such dam age is not covered by warranty Oil filler cap CHANGING
28. Programming HomeLink while you press and re press cycle your hand held transmitter every 2 seconds until the indicator light flashes rapidly indicating successful programming NOTE If programming a garage door opener etc it is advised to unplug the device during the cycling process to prevent possible damage to the garage door opener compo nents OPERATING THE INTEGRATED HomeLink UNIVERSAL TRANSCEIVER The Integrated HomeLink Universal Trans ceiver once programmed may now be used to activate the garage door etc To operate simply press the appropriate programmed In tegrated HomeLink Universal Transceiver button The red indicator light will illuminate while the signal is being transmitted PROGRAMMING PROBLEM DIAGNOSIS If the HomeLink does not quickly learn the hand held transmitter information e replace the hand held transmitter batteries with new batteries e position the hand held transmitter with its battery area facing away from the HomeLink surface e press and hold both the HomeLink and hand held transmitter buttons without inter ruption e position the hand held transmitter 2 to 5 inches 50 to 127 mm away from the HomeLink surface Hold the transmitter in that position for up to 15 seconds If HomeLink is not programmed within that time try holding the transmitter in another position keeping the indicator light in view at all times If you continue to
29. Radiator cap SDI0959 8 4 Do it yourself ENGINE COOLING SYSTEM The engine cooling system is filled at the factory with a high quality year round anti freeze coolant solution The anti freeze solu tion contains rust and corrosion inhibitors therefore additional cooling system additives are not necessary AA CAUTION When adding or replacing coolant be sure to use only a genuine NISSAN anti freeze coolant or equivalent with the proper mixture ratio of 50 anti freeze and 50 demineralized water distilled water The use of other types of coolant solutions may damage your engine cooling system Deminer alized water Outside temperature down to Anti freeze distilled water AA WARNING e Never remove the radiator cap when the engine is hot Serious burns could be caused by high pressure fluid escaping from the radiator Wait until the engine and radiator cool down e See If your vehicle overheats in the 6 In case of emergency section e The radiator is equipped with a pres sure cap To prevent engine damage use only a genuine NISSAN radiator cap CHECKING ENGINE COOLANT LEVEL Check the coolant level in the reservoir tank when the engine is cold If the coolant level is below MIN add coolant up to the MAX level If the reservoir tank is empty check the coolant level in the radiator when the engine is cold If there is insufficient coolant in the radiator fill the radiato
30. a dampened soft cloth CAR PHONE OR CB RADIO If equipped with a genuine NISSAN cellular phone your NISSAN features a non directional microphone in the steering column cover so it is not necessary to look at or speak directly into the microphone when calling To do so could detract from the driving operation and cause an accident See the car phone manual for operation Some models are pre wired to accept the genuine NISSAN cellular phone In addition the same model has the phone antenna built into the rear glass window When installing a CB ham radio or car phone in your NISSAN be sure to observe the follow ing cautions otherwise the new equipment may adversely affect the Engine control sys tem and other electronic parts AV WARNING e A cellular telephone should not be used while driving so full attention may be given to vehicle operation Some jurisdictions prohibit the use of cellular telephones while driving e If you must make a call while your vehicle is in motion the hands free cellular phone operational mode if so equipped is highly recommended Exercise extreme caution at all times so full attention may be given to ve hicle operation e If a conversation in a moving vehicle requires you to take notes pull off the road to a safe location and stop your vehicle before doing so CAUTION e Keep the antenna as far as possible away from the Engine Control Module ECM e Keep the antenna wire mo
31. aaee oaea a EEE NEEE Traction control system cancel switch TUM ESIQhal SWITCH sonnn T Tachometer 2 4 Temperature gauge Engine coolant temperature gage raria arnan cabaaecndencdapeatarnaieanteaeannasneste 2 5 Theft Nissan Vehicle Immobilizer System ENGNG Static ccnsenr scar rairareradnnaraen Theft warning Three way catalyst Tire PAG TING E ET TT 6 2 Teva WHEEIS cise ccseccerseceinenccenevecrsercens 8 32 Uniform tire quality grading 10 19 Wheel tire SiZ eee eeeeeeneeeeneee 10 9 Tits Spare rE tees coven teens bovess cocks teats eet ee 8 35 Tires Tire chains 8 33 Tires Tire placard 10 12 Tires Tire pressure 8 32 Titres Tire rotaties 8 34 TIRES TYPE Of UES suse cei Meats cheteeem reer cet 8 32 Top tether strap child restraint 1 34 Towing TOW thUCK TOWING asoeio ss 6 11 Towing a trailer 10 15 Towing load specification chart we 10 15 TOWINGS Sal OLY 2 cceszeccerscesennecsersansenevecnneese 10 17 Traction control system ou ee 5 20 Traction control system TCS cancel SWIT sassa sesi erya a Trailer towing Transceiver Integrated HomeLink Universal MRAMSCOIVON eusir edea ae aeee STEE 2 33 Transmission Automatic transmission fluid ATF 8 10 Driving with automatic transmission 5 8 Driving with manual transmission 5 11 Transmission selector lever lock release 5 9 Transmitter See multi remote control system Tra
32. brake pad requires replacement it will make a high pitched scraping or screeching sound when the vehicle is in motion whether or not the brake pedal is depressed Have the brakes checked as soon as possible if the wear indi cator sound is heard Under some driving or climate conditions oc casional brake squeak squeal or other noise may be heard Occasional brake noise during light to moderate stops is normal and does not affect the function or performance of the brake system Proper brake inspection intervals should be followed For additional information see Periodic maintenance schedules in the 9 Maintenance section for maintenance inter vals BRAKE BOOSTER Check the brake booster function as follows il With the engine off press and release the brake pedal several times When brake pedal movement distance of travel re mains the same from one pedal application to the next continue on to the next step While depressing the brake pedal start the engine The pedal height should drop a little With the brake pedal depressed stop the engine Keeping the pedal depressed for about 30 seconds the pedal height should not change Run the engine for one minute without depressing the brake pedal then turn it off Depress the brake pedal several times The pedal travel distance will decrease gradu ally with each depression as the vacuum is released from the booster If the brakes do not
33. condition is misuse of the vehicle for which NISSAN is not responsible Incorrect ignition timing will result in knocking after run or overheating This in turn may cause excessive fuel consumption or damage to the engine If any of the above symptoms 10 4 Technical and consumer information are encountered have your vehicle checked at a NISSAN dealer or other competent service facility However now and then you may notice light spark knock for a short time while accelerating or driving up hills This is no cause for concern because you get the greatest fuel benefit when there is light spark knock for a short time under heavy engine load API certification mark API service symbol ST10077 ENGINE OIL AND OIL FILTER RECOMMENDATION Selecting the correct oil It is essential to choose the correct quality and viscosity oil to ensure satisfactory engine life and performance NISSAN recommends the use of a low friction oil energy conserving oil in order to improve fuel economy and con serve energy Oils which do not have the specified quality label should not be used as they could cause engine damage Only those engine oils with the American Pe troleum Institute API certification mark on the front of the container should be used This type of oil supersedes the existing API SG or SH and Energy Conserving amp II categories If you cannot find engine oil with the API certification mark use an
34. could jam in the player e If a cassette has loose tape insert a pencil through one of the cassette hubs and rewind the tape firmly around the hubs Loose tape may cause tape jam ming and wavering sound quality e Over a period of time the playback head capstan and pinch roller may col lect a tape coating residue as the tape is played This residue accumulation can cause weak or wavering sound and should be removed periodically with a head cleaning tape If the residue is not removed periodically the player may need to be disassembled for cleaning ELAY PLAY STOP Push the PLAY STOP button while the cas sette tape is playing to stop the tape Push the button again to play the tape 1 aa 3 gt gt FF fast forward REW rewind Push either the FF or REW button for the desired direction The FF or REW symbol illuminates in the display To stop the FF or REW function press the FF or REW button again or the PLAY STOP button 4 ida APS 6 ppl APS automatic program search FF APS REW Push either the APS FF or APS REW button while the cassette tape is playing The tape runs quickly stops then plays the next selec tion Either the FF or REW symbol flashes in the display while searching for the selection This system searches at the blank intervals between selections If there is a blank interval within one selection or there is no interval between
35. damage to the charging system and cause per sonal injury 1 If the booster battery is in another vehicle position the two vehicles to bring their bat teries into close proximity to each other Do not allow the two vehicles to touch 2 Apply parking brake Move the shift lever to the N Neutral position On automatic transmission models move the selector lever to the P Park position Switch off all unnecessary electrical systems light heater air conditioner etc Remove vent caps on the battery if so equipped Cover the battery with an old cloth to reduce explosion hazard Connect jumper cables in the sequence as illustrated CAUTION e Always connect positive to posi tive and negative to body ground for example strut mounting bolt etc not to the battery e Make sure that cables do not touch moving parts in the engine compart ment and that clamps do not contact any other metal 5 Start the engine of the other vehicle and let it run for a few minutes 6 Keep the engine speed of the other vehicle at about 2 000 rpm and start your engine in the normal manner fA CAUTION Do not keep starter motor engaged for more than 10 seconds If the engine does not start right away turn the key off and wait 3 to 4 seconds before trying again 7 After starting your engine carefully discon nect the negative cable and then the posi tive cable 8 Replace the vent caps i
36. electrical accessory Use this power outlet with the engine running If the engine is stopped this could result in a discharged bat tery Avoid using when the air conditioner headlights or rear window defogger is on Before inserting or disconnecting a plug be sure to turn off the power switch of electrical accessory being used or the ACC power of the vehicle Push the plug in as far as it will go If good contact is not made the plug may overheat or the internal tempera ture fuse may blow When not in use be sure to close the cap Do not allow water to contact the socket CIGARETTE LIGHTER AND ASHTRAY accessory PULL to remove accessory Ce SIC1233 PUSH to heat accessory PUSH to open The cigarette lighter element is an accessory A genuine NISSAN cigarette lighter unit can be purchased from your local NISSAN dealer The cigarette lighter operates when the igni tion switch is in the ACC or ON position Push the lighter in all the way When the lighter is heated it will spring out Return the lighter to its original position after use AA WARNING The cigarette lighter should not be used while driving so full attention may be given to vehicle operation AA CAUTION The cigarette lighter socket is a power source for the cigarette lighter element only The use of the cigarette lighter socket as a power source for any other accessory is not recommended STORAGE
37. electrical system suspension system or front end structure This could affect proper operation of the supplemental air bag system Tampering with the supplemental front air bag system may result in serious personal injury Tampering includes changes to the steering wheel and the instrument panel as sembly by placing material over the steering wheel pad above the dash board or by installing additional trim material around the air bag system Work around and on the supplemen tal front air bag system should be done by an authorized NISSAN dealer Installation of electrical equip ment should also be done by an au thorized NISSAN dealer The SRS wir ing harnesses should not be modified or disconnected Unautho rized electrical test equipment and probing devices should not be used on the air bag system The SRS wiring harnesses are cov ered with yellow insulation either just before the harness connectors or over the complete harness for easy identification When selling your vehicle we request that you inform the buyer about the supplemental front air bag system and guide the buyer to the appropriate sections in this Owner s Manual Seats restraints and supplemental air bag systems 1 15 Supplemental side air bag system if so equipped The supplemental side air bags are located in the outside of the seatback of the front seats The supplemental side air bag on the driver or front passenger seat is de
38. from the windows and wiper blades e a sturdy flat board to be placed under the jack to give it firm support Starting and driving 5 21 e a shovel to dig the vehicle out of snow drifts e Watch for slippery spots glare ice pronged cheater adapters You can be These may appear on an otherwise injured by an electrical shock if you use sea WINE OW NASEN TENNES clear road in shaded areas If a patch an ungrounded connection ervoir tank Siig of ice is seen ahead brake before DRIVING ON SNOW OR ICE reaching it Try not to brake while actually on the ice and avoid any A WARNING sudden steering maneuvers e Do not use cruise control on slippery e Wet ice 32 F 0 C and freezing rain roads very cold snow or ice can be slick and very hard to drive on The vehicle will have a lot less traction or grip under these conditions Try to avoid driving on wet ice until the road is salted or e Snow can trap dangerous exhaust gases under your vehicle Keep snow clear of the exhaust pipe and from around your vehicle sanded e Whatever the condition drive with ENGINE BLOCK HEATER if so caution Accelerate and slow down equipped with care If accelerating or down An engine block heater to assist extreme cold shifting too fast the drive wheels will 9 temperature starting is available through your lose even more traction NISSAN dealer e Allow more stopping distance under these conditions Braking should be A WARNI
39. fumes are entering the vehicle drive with all windows fully open and have the vehicle inspected immediately e Do not run the engine in closed spaces such as a garage e Do not park the vehicle with the en gine running for any extended length of time e Keep the trunk lid closed while driv ing otherwise exhaust gases could be drawn into the passenger com partment If you must drive with the trunk lid open follow these precau tions 1 Open all the windows 2 Set the air recirculation switch OFF and the fan control at 4 high to circulate the air e If electrical wiring or other cable con nections must pass to a trailer through the seal on the trunk lid or the body follow the manufacturer s recommendation to prevent carbon monoxide entry into the vehicle If a special body or other equipment is added for recreational or other us age follow the manufacturer s rec ommendation to prevent carbon monoxide entry into the vehicle Some recreational vehicle appli ances such as stoves refrigerator heaters etc may also generate car bon monoxide The exhaust system and body should be inspected by a qualified mechanic whenever a The vehicle is raised for service b You suspect that exhaust fumes are entering into the passenger compartment c You notice a change in the sound of the exhaust system d You have had an accident involv ing damage to the exhaust system underbody or rear of
40. genuine oil filter or its equivalent Technical and consumer information 10 5 for the reason described in change intervals Change intervals The oil and oil filter change intervals for your engine are based on the use of the specified quality oils and filters Oil and filter other than the specified quality or oil and filter change intervals longer than recommended could re duce engine life Damage to engines caused by improper maintenance or use of incorrect oil and filter quality and or viscosity is not covered by the new NISSAN vehicle warran ties Your engine was filled with a high quality engine oil when it was built You do not have to change the oil before the first recommended change interval Oil and filter change intervals depend upon how you use your vehicle Op eration under the following conditions may require more frequent oil and filter changes e repeated short distance driving at cold out side temperatures e driving in dusty conditions e extensive idling e towing a trailer 10 6 Technical and consumer information RECOMMENDED SAE VISCOSITY NUMBER Outside Temperature Range Anticipated Before Next Oil Change GASOLINE ENGINE OIL 5W 30 PREFERRED TI1028 C SAE 5W 30 viscosity oil is preferred for all ambient temperatures SAE 10W 30 10W 40 viscosity oil may be used if the ambient temperature is above 0 F 18 C AIR CONDITIONING SYSTEM REFRIGERANT AND LUBRICANT RECOMMEN
41. glass to become coated with a film after the vehicle is parked in the hot sun Glass cleaner Appearance and care 7 3 and a soft cloth will easily remove this film fA CAUTION When cleaning the inside of the window do not use sharp edged tools abrasive cleaners or chlorine based disinfectant cleaners They could damage the elec trical conductors radio antenna ele ments or rear window defogger ele ments ALUMINUM ALLOY WHEELS Wash regularly especially during winter months in areas where road salt is used Salt could discolor the wheel if not removed CHROME PARTS Clean all chrome parts regularly with a non abrasive chrome polish to maintain the finish 7 4 Appearance and care CLEANING INTERIOR Occasionally remove loose dust from the inte rior trim plastic parts and seats using a vacuum cleaner or soft brush Wipe the vinyl and leather surfaces with a clean soft cloth dampened in mild soap solution then wipe clean with a dry soft cloth Before using any fabric protector read the manufacturer s rec ommendations Some fabric protectors con tain chemicals that may stain or bleach the seat material Use a cloth dampened only with water to clean the meter and gauge lens AA CAUTION e Never use gasoline thinner or any similar material e The leather seats should be regularly coated with a leather wax like saddle soap Never use car wax e Never use fabric protectors unless recommended by the m
42. have programming difficul ties please contact the NISSAN Consumer Affairs Department The phone numbers are located in the Foreword of this Owner s Manual CLEARING THE PROGRAMMED INFORMATION Individual buttons cannot be cleared however to clear all programming press and hold the two outside buttons and release when the indicator light begins to flash approximately 20 seconds ROLLING CODE PROGRAMMING Rolling code garage door openers or other rolling code devices which are code pro tected and manufactured after 1996 may be determined by the following A Reference the garage door opener Owner s Manual for verification B The hand held transmitter appears to pro gram the Integrated HomeLink Universal Transceiver but does not activate the ga rage door C Press and hold the trained HomeLink but ton If the garage door opener has the rolling code feature the HomeLink indica tor light will flash rapidly then remains on after 2 seconds To program the Integrated HomeLink Univer sal Transceiver to a garage door opener with the rolling code feature follow these instruc tions after completing the Programming HomeLink the aid of a second person may make the following procedures quicker and easier 1 Locate the training button on the garage door opener motor unit Exact location and Instruments and controls 2 35 color of the button may vary by garage door opener brand If there
43. influence of al cohol or drugs e Always observe posted speed limits and never drive too fast for condi tions e Always use your seat belts and appro priate child restraint systems Preteen children should be seated in the rear seat e Always provide information about the proper use of vehicle safety features to all occupants of the vehicle e Always review this Owner s Manual for important safety information MODIFICATION OF YOUR VEHICLE This vehicle should not be modified Modi fication could affect its performance safety or durability and may even violate governmental regulations In addition damage or performance problems result ing from modification may not be covered under NISSAN warranties WHEN READING THE MANUAL This manual includes information for all options available on this model Therefore you may find some information that does not apply to your vehicle All information specifications and illustrations in this manual are those in effect at the time of printing NISSAN reserves the right to change specifications or design at any time without notice IMPORTANT INFORMATION ABOUT THIS MANUAL You will see various symbols in this manual They are used in the following ways AA WARNING This is used to indicate the presence of a hazard that could cause death or serious personal injury To avoid or reduce the risk the procedures must be followed precisely fA CAUTION This is used to
44. is difficulty locating the training button reference the garage door opener Owner s Manual 2 Press the training button on the garage door opener motor unit which may activate a training light NOTE Following step 2 there are 30 seconds in which to initiate step 3 3 Firmly press and release the programmed HomeLink button Press and release the HomeLink button a second time to com plete the training process Some garage door openers may require you to do this procedure a third time to complete the training The garage door opener should now recognize the Integrated HomeLink Universal Trans ceiver and activate when the HomeLink but ton is pressed The remaining two buttons may now be programmed if not yet programmed follow steps 2 through 4 in the Programming HomeLink procedures earlier in this section REPROGRAMMING A SINGLE HomeLink BUTTON To reprogram an Integrated HomeLink Uni 2 36 Instruments and controls versal Transceiver button complete the follow ing 1 Press and hold the desired HomeLink button Do not release the button until step 4 has been completed 2 When the indicator light begins to flash slowly after 20 seconds position the hand held transmitter 2 to 5 inches 50 to 127 mm away from the HomeLink sur face 3 Press and hold the hand held transmitter button 4 The HomeLink indicator light will flash first slowly and then rapidly When the
45. is open replace it with a new fuse 5 If anew fuse also opens have the electrical system checked and repaired by your NISSAN dealer Do it yourself 8 23 MULTI REMOTE CONTROLLER BATTERY REPLACEMENT Suitable side up REMOVE the battery Replace the battery as follows 1 Open the lid using a suitable tool 2 Replace the battery with a new one Recommended battery Sanyo CR2025 or equivalent 8 24 Do it yourself Make sure that the side faces the bottom case 3 Close the lid securely 4 Push the remote controller button two or three times to check its operation See your NISSAN dealer if you need any assistance for replacement If the battery is removed for any reason other than replacement perform step 4 above e Be careful not to touch a circuit board and a battery terminal e An improperly disposed battery can harm the environment Always confirm local regulations for battery disposal e The remote controller is water resistant however if it does get wet immediately wipe completely dry e When changing batteries do not let dust or oil get on the controller FCC Notice Changes or modifications not expressly approved by the manufacturer compliance could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules and RSS 210 of Industry Canada Operation is subject to the following two conditions 1 This de vice ma
46. minutes 12 Turn the engine off 13 Repeat steps 1 through 8 at least one more time If step 1 through 7 is interrupted repeat the preceding step Any safe driving mode is ac ceptable between steps Do not stop the en gine until step 7 is completed Technical and consumer information 10 21 OWNER S MANUAL SERVICE MANUAL ORDER INFORMATION Genuine Nissan Service Manuals CG A genuine NISSAN Service Manual is the best source of service and repair information for your vehicle Filled with wiring diagrams illus trations and step by step diagnostic and ad justment procedures this manual is the same one used by the factory trained technicians working at authorized NISSAN dealerships Also available are genuine NISSAN Owner s Manuals and genuine NISSAN Service and Owner s Manuals for older NISSAN models 10 22 Technical and consumer information GET THE INSIDE STORY In the USA For current pricing and availability of genuine NISSAN Service Manuals for the 2000 model year contact Tweddle Litho Company 1 800 639 8841 www nissan techinfo com For current pricing and availability of genuine NISSAN Service Manuals for the 1999 model year and prior see an authorized NISSAN dealer or contact Dyment Distribution Services 20770 Westwood Dr Strongsville OH 44136 1 800 247 5321 For current pricing and availability of genuine NISSAN Owner s Manuals for the 2000 model year and prior see an authorize
47. nuts are missing and check for any loose nuts Tighten if necessary Tire rotation Tires should be rotated every 7 500 miles 12 000 km Wheel alignment and balance If the vehicle pulls to either side while driving on a straight and level road or if you detect uneven or abnormal tire wear there may be a need for wheel alignment If the steering wheel or seat vibrates at normal highway speeds wheel balancing may be needed Windshield wiper blades Check for cracks or wear if they do not wipe properly Doors and engine hood Check that all doors and the engine hood operate smoothly as well as the trunk lid or back hatch Also make sure that all latches lock securely Lubricate if nec essary Make sure that the secondary latch keeps the hood from opening when the pri mary latch is released When driving in areas using road salt or other corrosive materials check lubrication fre quently Inside the vehicle The maintenance items listed here should be checked on a regular basis such as when performing periodic maintenance cleaning the vehicle etc Lights Make sure that the headlights stop lights tail lights turn signal lights and other lights are all operating properly and installed securely Also check headlight aim Warning lights and chimes Make sure that all warning lights and chimes are operating properly Windshield wiper and washer Check that the wipers and washer operate properly and th
48. operate properly see your NISSAN dealer CLUTCH PEDAL 0 35 to 0 63 in 9 to 16 mm DI1021MC Press the pedal by hand and be sure the free travel is within the limits shown above If free travel is too little or too much see your NISSAN dealer FUSES CAUTION Never use a fuse of higher amperage rating than that specified on the fuse box cover This could damage the elec trical system or cause a fire Do it yourself 8 21 NISSAN dealer I j Sr to remove Q ENGINE COMPARTMENT If any electrical equipment does not operate check for an open fuse 1 Be sure the ignition key and headlight switch are OFF 2 Open the engine hood 3 Remove the fusible link cover 4 Remove the fuse with the fuse puller 5 If the fuse is open replace it with a new fuse 6 Ifa new fuse also opens have the electrical 8 22 Do it yourself system checked and repaired by your SDI0965 Fusible links If any electrical equipment does not operate and fuses are in good condition check the fusible links If any of these fusible links are melted replace only with genuine NISSAN parts Fuse puller SDI0966 PASSENGER COMPARTMENT If any electrical equipment does not operate check for an open fuse 1 Be sure the ignition key and the headlight switch are OFF 2 Pull to open the fuse box lid 3 Remove the fuse with the fuse puller 4 If the fuse
49. selector lever can also be moved if the ignition switch is in the ON position and the foot brake pedal is depressed There is an OFF position in between LOCK and ACC although it does not show on the lock cylinder When the ignition is in OFF the steering wheel is not locked In order for the steering wheel to be locked it must be turned about 1 6 of a turn counter clockwise from the straight up position To lock the steering wheel turn the key to the LOCK position Remove the key To unlock the steering wheel insert the key and turn it gently while rotating the steer ing wheel slightly right and left WARNING Never remove or turn the key to the LOCK position while driving The steer ing wheel will lock This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury Manual transmission model To remove the key TURN the key to LOCK while pushing the key in SSD0082C MANUAL TRANSMISSION The switch includes an anti theft steering lock device LOCK Normal parking position 0 The ignition key can only be removed when the switch is in this position On manual transmission models to turn the ignition key to LOCK from ACC or ON first turn the key to OFF and turn the key to LOCK while pushing the key in In order for the steering wheel to be locked it must be turned about 1 6 of a turn clockwise from the straight up position Starting an
50. service operators are generally familiar with the applicable laws and procedures for towing To assure proper towing and to pre vent accidental damage to your vehicle NISSAN recommends having a service opera tor tow your vehicle It is advisable to have the service operator carefully read the following precautions WARNING e Never ride in a vehicle that is being towed e Never get under your vehicle after it has been lifted by a tow truck AA CAUTION e When towing make sure that the transmission axles steering system and powertrain are in working condi tion If any unit is damaged dollies must be used Always attach safety chains before towing SCE0202 TOWING RECOMMENDED BY NISSAN NISSAN recommends that your vehicle be towed with the driving front wheels off the ground as illustrated In case of emergency 6 11 AA CAUTION e Always release the parking brake when towing with the rear wheels on the ground When towing manual transmission models with the front wheels on the ground If you do not use a towing dolly Turn the ignition key to the OFF posi tion and secure the steering wheel in a straight ahead position with a rope or similar device Never place the ignition key in the LOCK position This will result in damage to the steering lock mechanism Move the gearshift lever to the N Neutral position 6 12 In case of emergency
51. should be thoroughly checked by your NISSAN dealer SDI0119 AA WARNING Use only new fluid Old inferior or con taminated fluid may damage the brake and clutch systems The use of im proper fluids can damage the brake sys 8 12 Do it yourself tem and affect the vehicle s stopping ability AA CAUTION Do not spill the fluid on painted sur faces This will damage the paint If fluid is spilled wash with water WINDOW WASHER FLUID SDI0961 Type A Add fluid when the low washer fluid warning light comes on Add a washer solvent to the water for better cleaning In the winter season add a windshield washer anti freeze Follow the manufacturer s instructions for the mixture ratio Type B To check the fluid level use your finger to plug the center hole of the cap as shown above then remove it from the tank If there is no fluid in the tube add fluid Add a washer solvent to the water for better cleaning In the winter season add a windshield washer anti freeze Follow the manufacturer s instructions for the mixture ratio AA WARNING Anti freeze is poisonous and should be stored carefully in marked containers out of the reach of children AA CAUTION Do not substitute engine anti freeze coolant for window washer solution This may result in damage to the paint BATTERY e Keep the battery surface clean and dry Any corrosion should be washed off with a solution of baking
52. situations for example on slippery boat ramps WARNING Vehicle damage and or personal injury resulting from improper towing proce dures are not covered by NISSAN war ranties A Nissan Trailer Towing Guide U S only containing information on trailer towing ability and the special 10 16 Technical and consumer information equipment required may be obtained from an authorized NISSAN dealer Tongue load Keep the tongue load between 9 and 11 of the total trailer load If the tongue load be comes excessive rearrange cargo to allow for proper tongue load lt E wA AA 77 7 j Gross vehicle weight i j Q Q E Gross axle weight T11012M Maximum gross vehicle weight maximum gross axle weight The gross vehicle weight of the towing vehicle must not exceed GVWR shown on the F M V S S certification label The gross ve hicle weight equals the combined weight of the unloaded vehicle passengers luggage hitch trailer tongue load and any other optional equipment In addition front or rear gross axle weight must not exceed GAWR shown on the F M V S S certification label TOWING LOAD SPECIFICATION CHART Unit Ib kg MAXIMUM TOWING LOAD MAXIMUM TONGUE LOAD TOWING SAFETY Trailer hitch Choose a proper hitch for your vehicle and trailer A genuine NISSAN trailer hitch is avail able from your NISSAN dealer Canada only Make sure the trailer hi
53. soda and water Make certain the terminal connections are clean and securely tightened If the vehicle is not to be used for 30 days or longer disconnect the negative battery terminal cable to prevent discharge WARNING e Do not expose the battery to flames or electrical sparks Hydrogen gas generated by battery action is explo sive Do not allow battery fluid to contact your skin eyes fabrics or painted surfaces After touching a battery or battery cap do not touch or rub your eyes Thoroughly wash your hands If the acid contacts your eyes skin or clothing immediately flush with water for at least 15 minutes and seek medical attention e When working on or near a battery always wear suitable eye protection and remove all jewelry Do it yourself 8 13 e Battery posts terminals and related accessories contain lead and lead compounds Wash hands after han dling e Keep the battery out of the reach of children 8 14 Do it yourself Cell plug DI0137M Check the fluid level in each cell It should be between the MAX and MIN lines If it is necessary to add fluid add only distilled water to bring the level to the indicator in each filler opening Do not overfill 1 Remove the cell plugs 2 Add distilled water up to the MAX level 3 Tighten cell plugs If jump starting is necessary see Jump start ing the 6 In case of emergency section If the engine does not star
54. supplemental air bag warning light flashes intermittently e The supplemental air bag warning light does not come on at all Unless checked and repaired the Supplemen tal Restraint System and or the pre tensioner seat belt may not function properly For addi tional information see Supplemental restraint system in the 1 Seats restraints and supple mental air bag systems section A WARNING If the supplemental air bag warning light is on it could mean that the supplemen tal air bag system supplemental side air bag system if so equipped and or pre tensioner seat belt will not operate in an accident lt Low washer fluid warning light if so equipped This light comes on when the washer tank fluid is at a low level Add washer fluid as neces sary See Window washer fluid in the 8 Do it yourself section or srake Brake warning light This light functions for both the parking brake and the foot brake systems Parking brake indicator When the ignition key is in the ON position the light comes on when the parking brake is applied Low brake fluid warning light The light warns of a low brake fluid level If the light comes on while the engine is running with the parking brake not applied stop the vehicle and perform the following 1 Check the brake fluid level Add brake fluid as necessary See Brake and clutch fluid in the Do it
55. switch to the 74 or gt side and release it it need not be held The roof will automatically open or close all the way To stop the roof just press the switch toward the opposite A light press on the switch will cause the roof to open or close until the switch is released Auto reverse function When closing the sunroof If the control unit detects something caught in the sunroof as it moves to the front the sunroof will immediately open backward The auto reverse function can be activated when the sunroof is closed by automatic op eration when the ignition key is in the ON position or for about 45 seconds after the ignition key is turned to the OFF position e Depending on the environment or driv ing conditions the auto reverse function may be activated if an impact or load similar to something being caught in the sunroof occurs AA WARNING There are some small distances imme diately before the closed position which cannot be detected Make sure that all passengers have their hands etc in side the vehicle before closing the sun roof Tilting the sunroof To tilt up first close the sunroof then press and hold the side of the tilt switch To tilt down the sunroof press and hold the gt side Sun shade Open or close the sun shade by sliding it backward or forward The shade will open automatically when the sunroof is opened However it must be closed manually Instruments and contro
56. the cruise control is set Should this occur depress the clutch pedal and turn the main switch off immediately Failure to do so may cause 5 14 Starting and driving engine damage PRECAUTIONS ON CRUISE CONTROL e lf the cruise control system malfunctions it cancels automatically The SET indicator light on the meter panel then blinks to warn the driver e f the SET indicator light blinks turn the cruise control main switch off and have the system checked by your NISSAN dealer e The SET indicator light may blink when the cruise control main switch is turned on while pushing the RES ACCEL COAST SET or CANCEL switch located on the steering wheel To properly set the cruise control system perform the preceding steps in the order indicated Main switch SD0152 CRUISE CONTROL OPERATIONS The cruise control allows driving at a speed between 25 to 89 MPH 40 to 144 km h without keeping your foot on the accelerator pedal To turn on the cruise control push the main switch on The CRUISE indicator light on the meter panel will come on To set at cruising speed accelerate your vehicle to the desired speed push the COAST SET switch and release it The SET indicator light will come on Take your foot off the accelerator pedal Your vehicle will main tain the set speed Set switch PUSH and RELEASE for RES or ACCEL PUSH for CANCEL PUSH and RELEASE for COAST SET aay 4 e To pass
57. the reset knob for more than 1 second resets the trip odometer to zero You can change the display of the trip odom eter between A and B and reset them while the odometers are illuminated for about 30 sec onds after the ignition switch has been turned off A Red zone DO NOT REV engine into red zone SIC1249 TACHOMETER The tachometer indicates engine speed in revolutions per minute r min CAUTION When engine speed approaches the red zone shift to a higher gear Operating the engine in the red zone may cause serious engine damage Normal range IC0173 ENGINE COOLANT TEMPERATURE GAUGE The gauge indicates the engine coolant tem perature The engine coolant temperature will vary with the outside air temperature and driving condi tions CAUTION If the gauge indicates engine coolant temperature over the normal range stop the vehicle as soon as safely possible If the engine is overheated continued op eration of the vehicle may seriously damage the engine See If your vehicle overheats in the 6 In case of emer gency section for immediate action re quired Empty SIC0879 FUEL GAUGE The gauge indicates the approximate fuel level in the tank The gauge may move slightly during braking turning acceleration or going up or down hill The gauge needle is designed to move to the E Empty position when the ignition key is turned to the OFF p
58. the wheel nut wrench Do not remove the wheel nuts until the tire is off the ground 3 Carefully raise the vehicle until the tire clears the ground To lift the vehicle se curely hold the jack lever and rod with both hands as shown above Remove the wheel nuts and then remove the tire AA WARNING e Never get under the vehicle while it is supported only by the jack Use only the jack provided with your vehicle to lift the vehicle Do not use the jack provided with your vehicle on other vehicles The jack is designed only for lifting your vehicle during a tire change Use the correct jack up points never use any other part of the vehicle for jack support Never jack up the vehicle more than necessary Never use blocks on or under the jack Do not start or run engine while ve hicle is on the jack as it may cause the vehicle to move This is especially true for vehicles with limited slid dif ferential carriers Do not allow passengers to stay in the vehicle while it is on the jack In case of emergency 6 5 SCE0039 Installing the spare tire 1 Clean any mud or dirt from the surface between the wheel and hub 2 Carefully put the wheel on and tighten the wheel nuts finger tight 3 With the wheel nut wrench tighten wheel nuts alternately and evenly until they are tight 4 Lower the vehicle slowly until the tire touches the ground Then with the wheel nut wrench tighten the wheel n
59. times to skip through programs The tape will advance the number of times the button is pushed up to nine programs When the 4 APS REW button is pushed once the program being played starts over from the beginning Push the 44 APS REW button several times to skip back sev eral selections The tape will go back the number of times the button is pushed Either the FF or REW symbol flashes on the right side of the display window while searching for the selection This system searches for the blank intervals between selections If there is a blank interval within one program or there is no interval between programs the system may not stop in the desired or expected location PROG Program Push the PROG button to change the tape side while the tape is being played The cassette tape will automatically change directions to play the other side when the first side is completed Dolby NR Noise Reduction Push the Dolby NR Q button for Dolby NR encoded tapes to reduce high frequency tape noise The indicator will come on Dolby noise reduction manufactured under li cense from Dolby Laboratories Licensing Cor poration Dolby NR and the double D symbol OO are trademarks of Dolby Laboratories Licensing Corporation Metal or chrome tape usage The cassette player will be automatically set to high performance play when playing a metal or chrome cassette tape 4 TAPE EJECT When this button is pushed with the t
60. to be inspected more frequently Exhaust system Visually check the exhaust pipes muffler and hangers for proper attach ment leaks cracks chafing abrasion dete rioration etc Under severe driving conditions inspection should be performed more fre quently Supplemental air bag and supplemental side air bag if so equipped systems Main tenance for the supplemental air bags or supplemental side air bags should be done by an authorized NISSAN dealer Automatic Speed Control Device ASCD vacuum hoses Check vacuum hose be tween ASCD actuator and ASCD pump for breakage cracks or fracture 10 Technical and consumer information Capacities and recommended fuel lubricants 10 2 Fuel recommendation ccccecceeeeeeeeeeeeeseeeeeeeees Engine oil and oil filter recommendation ved Recommended SAE viscosity numbet Air conditioning system refrigerant and lubricant recommendations cceeeeeeeeeeeeteeeeeeeeeeeeeeeeeeteaeeee 10 6 Specifications ss 10 7 Engine aser aa 10 7 Tires and wheels we 10 9 Dimensions and weights csceeeeeeeeeeeee 10 9 When traveling or registering your vehicle in another COUNUY sires cssesecescetsseveeceeusceevey ceesveiiieesieys 10 10 Vehicle identification eee ee eeeeeeeeteeeeeeeees 10 10 Vehicle identification number VIN plate 10 10 Vehicle identification number CHASSIS MUMDEN iissa a
61. when the engine hood is opened Make sure the wiper blade contacts the glass otherwise the arm may be dam aged from wind pressure Windshield washer nozzle p s Needle or small pin If you wax the surface of the hood be careful not to let wax get into the washer nozzle This may cause clogging or im proper windshield washer operation If wax gets into the nozzle remove it with a needle or small pin Do it yourself 8 19 PARKING BRAKE AND BRAKE PEDAL 10 to 11 clicks under pulling force of 44 lb 196 N SDI0125 A T models 3 1 8 in 80 mm or more eat depressing HAS rapa 110 Ib 490 N 3 in 75 mm or more DI1020MF CHECKING PARKING BRAKE From the released position pull the parking brake lever up slowly and firmly If the number of clicks is out of the range listed above see your NISSAN dealer 8 20 Do it yourself CHECKING BRAKE PEDAL With the engine running check the distance between the upper surface of the pedal and the metal floor If it is out of the range shown above see your NISSAN dealer Self adjusting brakes Your vehicle is equipped with self adjusting brakes The disc type brakes self adjust every time the brake pedal is applied AA WARNING See your NISSAN dealer and have it checked if the brake pedal height does not return to normal Brake pad wear indicators The disc brake pads on your vehicle have audible wear indicators When a
62. will go back the number of times the button is pushed PROG Program When the PROG button is pushed while the compact disc is being played the play pattern will change as follows no mark All the programs will be played repeatedly in sequence 1 Only one program the one being played when the PROG button is pushed will be repeated RANDOM Programs will be played at random not following the sequence on the compact disc The same program may be repeated twice When the compact disc is ejected the play pattern will automatically change to no mark 4 CD EJECT When the CD EJECT button is pushed with the compact disc loaded the compact disc will be ejected When this button is pushed while the compact disc is being played the compact disc will come out and the system will turn off If the compact disc comes out and is not removed it will be pulled back into the slot to protect it without 8 cm diameter com pact discs CD IN indicator CD IN indicator appears on the display when the CD is loaded with the system on ANTENNA Window antenna The antenna pattern is printed inside the rear window AA CAUTION e Do not place metalized film near the rear window glass or attach any metal parts to it This may cause poor re ception or noise e When cleaning the inside of the rear window be careful not to scratch or damage the rear window antenna Lightly wipe along the antenna with
63. with inside lock Knob eee eee 3 3 Locking with power door lock switch eee 3 3 Child safety rear door lOCK e eee eee eens 3 4 Multi remote control system if so equipped 3 4 How to use multi remote control system 3 4 Opener operation Key operation Fuel filler lid Opener operation Fuel filler cap Steering wheel Tilt operation Sun visors Mirrors Inside mirror Outside mirrors KEYS Master keys 0x1234 Key number plate IC1239 You can only drive your vehicle using the master or security keys which are registered to the Nissan Vehicle Immobilizer System com ponents in your vehicle These keys have a transponder chip in the key head The master key can be used for all the locks The security key cannot be used for the trunk lid or glove box locks To protect belongings when you leave a key with someone give them the security key only Never leave these keys in the vehicle Record the key number on the key number plate supplied with your keys and keep it in a 3 2 Pre driving checks and adjustments safe place such as your wallet not in the vehicle NISSAN does not record any key numbers so it is very important to keep track of your key number plate A key number is only necessary when you have lost all keys and do not have one to duplicate from If you still have a key this key can be
64. x 1 000 75 15 22 5 30 37 5 45 52 5 60 a nee a 0D e B D O a a 88 Months 6 12 18 24 30 36 42 48 Emission control system maintenance Drive belts See NOTE 1 I Air cleaner filter R R EVAP vapor lines IF Ir Fuel lines IF Ir Fuel filter See NOTE 2 Engine coolant See NOTE 3 R Engine oil R R R R R R R R Engine oil filter Use part No 15208 31U01 or equivalent R R R R R R R R Spark plugs Use PLATINUM TIPPED type Replace every 105 000 miles 169 000 km Intake amp exhaust valve clearance See NOTE 4 NOTE 1 After 60 000 miles 96 000 km or 48 months inspect every 15 000 miles 24 000 km or 12 months 2 Maintenance free item 3 After 60 000 miles 96 000 km or 48 months replace every 30 000 miles 48 000 km or 24 months 4 If valve noise increases inspect valve clearance Maintenance items and intervals with are recommended by NISSAN for reliable vehicle operation The owner need not perform such maintenance in order to maintain the emission warranty or manufacturer recall liability Other maintenance items and intervals are required 9 8 Maintenance Schedule 2 Abbreviations Inspect Correct or replace if necessary MAINTENANCE OPERATION MAINTENANCE INTERVAL Miles x 1 000 7 5 15 22 5 30 37 5 45 52 5 60 km x 1 000 12 24 36 48 60 72 84 96 Months 6 12 18 24 30 36 42 48 Perform at number of miles kilometers or months whichever comes first Chassis and body maintenance Brake li
65. 1 4 qt 3 7 e ILSAC grade GF I amp GF II 2 3 Cooling system With reservoir 8 1 8 qt 6 3 4 qt 7 7 7 z Genuine NISSAN anti freeze coolant or equivalent Reservoir 3 4 qt 5 8 qt 0 7 Manual transmission gear oil API GL 4 Viscosity SAE 75W 90 only Automatic transmission fluid Power steering fluid Refill to the proper oil level according to the instructions in the 8 Do it yourself section Brake and clutch fluid Nissan Matic D Continental U S and Alaska or Canada NISSAN Auto matic Transmission Fluid 4 Genuine Nissan PSFII or equivalent 8 Genuine Nissan Brake Fluid 5 or equivalent DOT 3 US FMVSS No 116 Multi purpose grease Air conditioning system refrigerant NLGI No 2 Lithium soap base HFC 134a R 134a 7 Air conditioning system lubricants Nissan A C System Oil Type S or exact equivalent Ae 2 3 4 5 6 s 8 For additional information see later in this paragraph for fuel recommendation For additional information see later in this paragraph for engine oil and oil filter recommendation For additional information see later in this paragraph for recommended SAE viscosity number Dexron III Mercon or equivalent may also be used Outside the continental United States and Alaska contact a NISSAN dealer for more information regarding suitable fluids including recommended brand s of Dexron III Mercon automatic transmission fluid A
66. 10 10 Engine serial nUMber eee eeseeseeeeeeeeeeeeeees 10 11 F M V S S certification label ee 10 11 Emission control information label 0 10 11 Tire placard ts Air conditioner specification label 10 12 Installing front license plate ee 10 13 Vehicle loading information ws 10 14 TEM Sensasi id Determining vehicle load capacity vw 10 14 Loading TDS esae Towing a trailer Maximum load limits ve TOWING Salely ieissar Uniform tire quality grading ee Emission control system warranty ie Reporting safety defects US only 10 20 Readiness for inspection maintenance I M test US OMY secsivedissoctsorssosusbescaeseiusesteseboesiscnetanezizesceais 10 21 CAPACITIES AND RECOMMENDED FUEL LUBRICANTS The following are approximate capacities The actual refill capacities may be a little different When refilling follow the procedure instructed in the 8 Do it yourself section to determine the proper refill capacity Capacity Approximate Recommended ne mp Liter specifications measure measure Fuel 18 1 2 gal 15 3 8 gal 70 Unleaded gasoline with an octane rating of at least 91 AKI RON 96 1 Engine oil 6 Drain and refill ee oxi API Certification Mark 2 3 1 4 1 2 4 3 Witty lb iter change Aiea slegt 7 e API grade SG SH Energy Conserving amp Il or API grade SJ Energy j ae Conserving 2 3 Without oil filter change 3 7 8 at 3
67. 9 AUMtOMALIG SUIOOT s550ceeee2e5a fseasseeeetssceeszssotsthaaiseese 2 29 SOCK ni te axes ce teescs sai dunet a A cosets 2 30 Adjusting the time iiipin eiaa 2 30 Interior ight iiics GelING E E A A TT Personal light Vanity mirror light if so equipped 2 32 Trunk IQUE soraan 2 33 Integrated HomeLink Universal Transceiver if SO CQUIPPO cs sissesiiocsscessaeseceubensocdvsensaescdanaccsises 2 33 Programming HOMALINK cccesscsaccescosssasersecosersss Programming HomeLink for Canadian GUSTOIMEGNS cii an irei naa aa a iia Operating the integrated HomeLink Universal TWANISCOIN Cl aissein nescii renoster impii Programming problem Diagnosis 0 ce ee 2 35 Clearing the programmed information 2 35 Rolling code programming cceee eee 2 35 Reprogramming a single HomeLink button 2 36 If your vehicle is Stolen cceceeeeeeeeeeseceeeeeeeeeees 2 36 INSTRUMENT PANEL Windshield wiper washer switch P 2 15 Ventilator P 4 2 Rear window and outside mirror if so equipped defogger switch P 2 16 Heater air conditioner control P 4 3 Clock P 2 30 Security indicator light P 2 12 Traction control system TCS cancel switch if so equipped P 2 22 Cruise control main switch P 5 14 Meters gauges P 2 3 Radio cassette player P 4 14 CD player P 4 19 Instrument brightness control switch P 2 18 Passenger supplemental air bag P 1 8
68. AN affiliates world wide collectively growing to be come the fifth largest automaker in the world In addition to cars and trucks NISSAN also makes textile machinery fork lift trucks marine engines boats and other products NISSAN has made a substantial and growing investment in North America starting with the opening of Nissan Motor Corporation U S A in 1960 and continuing with the production of some cars and trucks at one of the world s most modern manufacturing facilities Nissan Motor Manufacturing Corporation U S A in Smyrna Tennessee vehicle styling at Nissan Design International in San Diego California and engi neering at Nissan Research and Development in Farmington Hills Michigan NISSAN and its dealers indirectly employ about 60 000 Americans NISSAN is also a substantial contributor to the Canadian economy Nissan Canada Inc its sup pliers and over 140 dealers employ approxi mately 4 500 people These include company employees and the staffs of NISSAN dealers all across Canada In addition many Canadians work for companies that supply NISSAN and NISSAN dealers with materials and services ranging from operation of port facilities and trans portation services to the supply of lubricants parts and accessories NISSAN pioneered the use of electronics and computers in automobiles and has led the indus try in improving both performance and fuel effi ciency through new engine designs and the use of s
69. BE Take care not to spill gasoline during refu eling Gasoline containing oxygenates can cause paint damage Aftermarket fuel additives NISSAN does not recommend the use of any fuel additives i e fuel injector cleaner octane booster intake valve deposit removers etc which are sold commercially Many of these additives intended for gum varnish or deposit removal may contain active solvent or similar ingredients that can be harmful to the fuel system and engine Technical and consumer information 10 3 Octane rating tips In most parts of North America you should use unleaded gasoline with an octane rating of at least 87 or 91 AKI Anti Knock Index number However you may use unleaded gasoline with an octane rating as low as 85 AKI number in these high altitude areas over 4 000 ft 1 219 m such as Colorado Montana New Mexico Utah Wyoming northeastern Nevada south ern Idaho western South Dakota western Nebraska and that part of Texas which is directly south of New Mexico Using unleaded gasoline with an octane rating lower than stated above can cause persistent heavy spark knock Spark knock is a metallic rapping noise If se vere this can lead to engine damage If you detect a persistent heavy spark knock even when using gasoline of the stated octane rating or if you hear steady spark knock while holding a steady speed on level roads have your dealer correct the condi tion Failure to correct the
70. DATIONS The air conditioning system in this NISSAN vehicle must be charged with the refriger ant HFC 134a R 134a and the lubricant Nissan A C System Oil Type S or the exact equivalents AA CAUTION The use of any other refrigerant or lubri cant will cause severe damage to the air conditioning system and will require the replacement of all air conditioner sys tem components The refrigerant HFC 134a R 134a in your NISSAN vehicle will not harm the earth s ozone layer Although this refrigerant does not affect the earth s atmosphere certain govern mental regulations require the recovery and recycling of any refrigerant during automotive air conditioning system service Your NISSAN dealer has the trained technicians and equip ment needed to recover and recycle your air conditioning system refrigerant SPECIFICATIONS Contact your NISSAN dealer when servicing ENGINE your air conditioning system Model VQ30DE Type Gasoline 4 cycle Cylinder arrangement 6 cylinder V slanted at 60 Bore x Stroke in mm 3 66 x 2 886 93 0 x 73 3 Displacement cu in cm 182 33 2 988 Firing order 1 2 3 4 5 6 Idle speed rpm Soei o Pabel Ignition timing B T D C degree rpm he ae asl aaa CO percentage at idle speed No air Standard PFR5G 11 Spark plug z F Service option PFR4G 11 PFR6G 11 Spark plug gap Normal in mm 0 043 1 1 Camshaft operation Timing chain Alternator belt size Width x Length in mm
71. Foreword Welcome to the growing family of new NISSAN owners This vehicle is delivered to you with confidence It was produced using the latest techniques and strict quality control This manual was prepared to help you under stand the operation and maintenance of your vehicle so that you may enjoy many miles of driving pleasure Please read through this manual before operating your vehicle A separate Warranty Information and Main tenance Log Booklet in U S Warranty and Roadside Assistance Information booklet in Canada explains details about the warranties covering your vehicle and vehicle maintenance schedules Addition ally a separate Customer Care Lemon Law Booklet U S only will explain how to resolve any concerns you may have with your vehicle as well as clarify your rights under your state s lemon law Your NISSAN dealer knows your vehicle best When you require any service or have any questions he will be glad to assist you with the extensive resources available to him READ FIRST THEN DRIVE SAFELY Before driving your vehicle please read your Owner s Manual carefully This will ensure familiarity with controls and main tenance requirements assisting you in the safe operation of your vehicle WARNING IMPORTANT SAFETY INFORMA TION REMINDERS FOR SAFETY Follow these important driving rules to help ensure a safe and comfortable trip for you and your passengers e Never drive under the
72. ING BRAKE PULL to fo apply PUSH to release SSD0018 To apply pull the lever up To release 1 2 Firmly apply foot brake Automatic transmission models Move the selector lever to the P Park position Manual transmission models Place the shift lever in the N Neutral position While pulling up on the lever slightly push the button and lower completely 4 Before driving be sure the brake warning light goes out AA WARNING e Be sure the parking brake is fully released before driving Failure to do so can cause brake failure and lead to an accident e Do not release the parking brake from outside the vehicle e Do not use the gear shift in place of the parking brake When parking be sure the parking brake is fully en gaged e Do not leave children unattended in a vehicle They could release the park ing brake and cause an accident Starting and driving 5 13 CRUISE CONTROL AA WARNING Do not use the cruise control when driv ing under the following conditions e it is not possible to keep the vehicle at a set speed e in heavy traffic or in traffic that varies in speed e on winding or hilly roads e on slippery roads rain snow ice etc e in very windy areas Doing so could cause a loss of vehicle control and result in an accident AA CAUTION On manual transmission models do not shift into N Neutral without depressing the clutch pedal when
73. ISC CD PLAYER Audio main operation Head unit The radio has an FM diversity reception sys tem which employs two antennas One is a rod type antenna the other is an antenna printed on the window This system automati cally switches to the antenna which is receiv ing less noise The tape deck employs a permalloy head which allows for improved reproduction of high frequency ranges Noise is also greatly re duced by the combined use of the Dolby NR Noise Reduction system The auto loudness circuit enhances the low frequency range au tomatically in both radio reception and tape and CD playback ON OFF Volume control Turn the ignition key to ACC or ON and then push the ON OFF VOL control knob while the system is off to call up the mode radio tape or CD which was playing immediately before the system was turned off When no CD or tape is loaded the radio will come on While the system is on pushing the ON OFF VOL con Heater air conditioner and audio systems 4 19 TTT By BAS gt TRE FAD BAL AUDIO TUNE DISC Select the audio mode Adjust to the desired level SAA0381 trol knob turns the system off To turn the radio off press the ON OFF VOL control knob Turn the ON OFF VOL control knob to adjust the volume Adjusting tone quality and speaker balance To adjust BASS TRE Treble BAL Balance and FAD Fader press the AUDIO button until the desired mode BAS T
74. K SCAN tuning button or for less than 1 5 seconds SEEK tuning begins from high to low or low to high frequen cies and stops at the next broadcasting sta Heater air conditioner and audio systems 4 15 tion Pushing the button again continues the SEEK function Once the highest broadcasting station is reached the radio continues in the SEEK mode at the lowest broadcast station Push the SEEK SCAN tuning button x or for more than 1 5 seconds SCAN illu minates in the display window SCAN tuning begins from high to low or low to high frequen cies and stops at each broadcasting station for 5 seconds Pushing the button again during this 5 second period stops SCAN tuning and the radio remains tuned to that station 4 16 Heater air conditioner and audio systems WD Select ma 1 n guai 22000022897 SEEK SCAN tuning TpewseAN A D Push Tar r goi ZIZEL Confirm Sound resumes when memorizing is complete Manual tuning ve SS A pushing GG0foMovaaaA SAA0264 Station memory operations Six stations can be set for the AM band 12 stations can be set for the FM band six for FM1 six for FM2 1 Push the FM AM band select button to select AM FM1 or FM2 The selected band illuminates in the display 2 Tune to the desired station 3 Push the desired select button for more than 1 5 seconds For example in the illustrations ch2 is to be memorized The
75. MDODY s cccicz cesses seivicecactesastacteiiesc ieseeastastenioeaiteses GIASS sedacssecispicazeeetetseeoeneso Aluminum alloy wheels Chrome parts Gleaning IMNON seenior ie aa a Floor MALS x oeei cosets ea a a a eels 7 4 Seat DEMS aissein dr cde cesascetescensasdedafiesthpistescesacsanease 7 5 Corrosion proteto iscir 7 5 Most common factors contributing to vehicle COMOSION Ea E E E EE E 7 5 Environmental factors influence the rate of GCONMMOSIO Mes enre ed a E e 7 5 To protect your vehicle from corrosion s 7 6 CLEANING EXTERIOR In order to maintain the appearance of your vehicle it is important to take proper care of it In the following cases please wash your ve hicle as soon as possible to protect the paint surface e After a rainfall to prevent possible damage from acid rain e After driving on coastal roads e When contaminants such as soot bird droppings tree sap metal particles or bugs get on the paint surface e When dust or mud builds up on the surface 7 2 Appearance and care Whenever possible store or park your vehicle inside a garage or in a covered area When it is necessary to park outside park ina shady area or protect the vehicle with a body cover Be careful not to scratch the paint surface when putting on or removing the body cover WASHING Thoroughly rinse surface dirt off the vehicle with a wet sponge and plenty of clean water Clean the vehi
76. MULTI REMOTE CONTROL SYSTEM if so equipped It is possible to lock unlock all doors to release the trunk lid and activate the panic alarm by using the remote controller from outside the vehicle Before locking the doors make sure the key is not left in the vehicle The remote controller can operate at a dis tance of approximately 33 ft 10 m from the vehicle The effective distance depends upon the conditions around the vehicle As many as four remote controllers can be used with one vehicle For information con cerning the purchase and use of additional remote controllers contact your NISSAN dealer The multi remote controller will not function when e the battery is dead e the distance between the vehicle and the remote controller is over 33 ft 10 m The panic alarm will not activate when the key is in the ignition switch CAUTION The following conditions or occurrences will damage the remote controller e Do not allow the remote controller to become wet e Do not drop the remote controller e Do not strike the remote controller sharply against another object e Do not place the remote controller for an extended period in an area where temperatures exceed 140 F 60 C If a multi remote controller is lost or stolen NISSAN recommends erasing the ID code of that controller This will prevent the controller from unautho rized use to unlock the vehicle For in formation regarding the erasing pr
77. NG started sooner than on dry pavement e Allow greater following distances on Do not use your heater with an un slippery roads grounded electrical system or two 5 22 Starting and driving 6 In case of emergency Flat tiin iias Changing a flat tire Jump starting Push starting If your vehicle Overheats siiisiirisiinnrii 6 10 Towing your v ho oo eeeeeeeeeeeeceeeeseeneeeeeneees 6 11 Towing recommended by NISSAN eee 6 11 Vehicle recovery Freeing a stuck vehicle 6 12 FLAT TIRE CHANGING A FLAT TIRE If you have a flat tire follow the instructions below Stopping the vehicle 1 Safely move the vehicle off the road away from traffic 2 Turn on the hazard warning flashers 3 Park on a level surface and apply the parking brake Shift the manual transmis sion into R Reverse position automatic transmission in P Park position 4 Turn off the engine 5 Raise the hood to warn other traffic and to signal professional road assistance person nel that you need assistance 6 Have all passengers get out of the vehicle and stand in a safe place away from traffic and clear of the vehicle AA WARNING e Make sure that the parking brake is securely applied and the manual transmission is shifted into R Re 6 2 In case of emergency verse or the automatic transmission into P Park Never change tires when the vehicle is on a slope ice or slippery areas This is hazard
78. RE FAD or BAL appears in the display Press the y or AN button to adjust Bass BAS and Treble TRE to the desired level Use the x or 4 20 Heater air conditioner and audio systems A button also to adjust Fader FAD or Balance BAL modes FAD adjusts the sound level between the front and rear speakers and BAL adjusts the sound between the right and left speakers After 10 seconds the radio or cassette tape display reappears Once the sound quality is set to the desired level press the AUDIO button repeatedly until the radio or cassette tape display appears FM AM radio operation FM AM band select Pushing the FM AM band select button will change the band FM1 FM2 or AM FM AM When FM AM band select button is pushed while the ignition switch is in the ACC or ON the radio will come on at the station last played The last station played will also come on when the power knob is turned to ON If a compact disc or tape is playing when the FM AM band select button is turned to ON the compact disc or tape will automatically be turned off and the last radio station played will come on The FM stereo indicator ST will glow during FM stereo reception When the stereo broad cast signal is weak the radio will automatically change from stereo to monaural reception VWI nm TUNE Tuning WARNING The radio should not be tuned while driving so full attention may be given to veh
79. RITY SYSTEMS IC0005 Indicator light SECURITY SIC1228 Your vehicle has two types of security sys tems as follows e Theft warning if so equipped e Nissan Vehicle Immobilizer System The security condition will be shown by the security indicator light THEFT WARNING if so equipped The theft warning system provides visual and audio alarm signals if parts of the vehicle are disturbed Security indicator light This light will indicate for the theft warning system and the Nissan Vehicle Immobilizer system This light blinks whenever the ignition switch is in the LOCK OFF or ACC position This function indicates the security systems equipped on the vehicle are operational How to activate the theft warning system 1 Close all windows The system can be activated even if the windows are open 2 Remove the key from the ignition switch 3 Close and lock all doors hood and trunk lid The doors can be locked either with or without the key Multi remote controller equipped models Close and lock all doors hood and trunk lid Lock all doors by the key or pressing the LOCK button on the multi remote controller At this time the hazard indicators flash twice to indicate all doors are locked 4 Confirm that the SECURITY indicator light comes on The SECURITY light glows for about 30 seconds and then blink The sys tem is now activated If during this 30 second time period the door i
80. RVICE s ENGINE SLIP SOON BRAKE Brake warning light Anti lock brake warning light if so equipped Low fuel warning light Overdrive off indicator light Turn signal hazard indicator light High beam indicator light Blue WARNING LIGHTS y Engine oil pressure warning light This light warns of low engine oil pressure If the light flickers or comes on during normal driving pull off the road in a safe area stop the engine immediately and call a NISSAN dealer or other authorized repair shop The oil pressure warning light is not de signed to indicate a low oil level Use the dipstick to check the oil level See Engine oil in the 8 Do it yourself section CRUISE Cruise main switch indicator light SET Cruise set indicator light SERVICE ENGINE SOON Malfunction indicator lamp MIL TCS OFF Traction control system indicator light if so equipped SLIP Slip indicator light if so equipped AA CAUTION Running the engine with the oil pressure warning light on could cause serious damage to the engine almost immedi ately Turn off the engine as soon as it is safe to do so Charge warning light If the light comes on while the engine is running it may indicate that there is something wrong with the charging system Turn the Instruments and controls 2 7 engine of
81. SH SPA0986 KEY OPERATION OPENER OPERATION To open the trunk lid turn the key clockwise To open the fuel filler lid push the opener To close lower and push the trunk lid down switch To lock close the fuel filler lid securely securely 3 10 Pre driving checks and adjustments LOOSEN Fuel filler cap holder SPA0653 FUEL FILLER CAP The fuel filler cap is a ratcheting type Tighten the cap clockwise until ratcheting clicks are heard Put the fuel filler cap on the cap holder while refueling AA WARNING e Gasoline is extremely flammable and highly explosive under certain condi tions You could be burned or seri ously injured if it is misused or mis handled Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refuel ing Fuel may be under pressure Turn the cap one half turn and wait for any hissing sound to stop to prevent fuel from spraying out and possible per sonal injury Then remove the cap e Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically Continued refueling may cause fuel overflow resulting in fuel spray and possibly a fire Use only a genuine fuel filler cap as a replacement It has a built in safety valve needed for proper operation of the fuel system and emission control system An incorrect cap can result in a serious malfunction and possible injury Never pour fuel into t
82. TERVAL Perform at number of miles Miles x 1 000 38 75 113 15 188 225 263 30 338 375 413 45 488 525 563 60 kilometers or months which km x 1 000 6 12 18 24 30 36 42 48 54 60 66 72 78 84 90 96 ever comes first Months 3 6 9 12 15 18 21 24 27 30 33 36 39 42 45 48 Emission control system maintenance Drive belts See NOTE 1 IF Air cleaner filter See NOTE 2 R R EVAP vapor lines I j Fuel lines IF Fuel filter See NOTE 3 Engine coolant See NOTE 4 R Engine oil R R R R R R R R R R R R R R R R Engine oil filter Use part No 15208 31U01 or equivalent R R R R R R R R R R R R R R R R Spark plugs Use PLATINUM TIPPED type Replace every 105 000 miles 169 000 km Intake amp exhaust valve clear ance See NOTE 5 NOTE 1 After 60 000 miles 96 000 km or 48 months inspect every 15 000 miles 24 000 km or 12 months 2 If operating mainly in dusty conditions more frequent maintenance may be required 3 Maintenance free item 4 After 60 000 miles 96 000 km or 48 months replace every 30 000 miles 48 000 km or 24 months 5 If valve noise increases inspect valve clearance Maintenance items and intervals with are recommended by NISSAN for reliable vehicle operation The owner need not perform such maintenance in order to maintain the emission warranty or manufacturer recall liability Other maintenance items and intervals are required 9 6 Maintenance Schedule 1 Abbreviatio
83. The air conditioner cooling function oper ates only when the engine is running 4 4 Heater air conditioner and audio systems HEATER OPERATION Heating This mode is used to direct hot air from the floor outlets Some air will also come from the defrost vents 1 Push the air recirculation button to the OFF position for normal heating 2 Push the g button in 3 Turn on the fan control dial 4 Move the temperature control lever to the desired position between the middle and the HOT position For quick heating move the air recirculation button to the ON position Be sure to return the air recirculation button to the OFF position for normal heating Ventilation This mode directs outside air from the side and center vents 1 Push the air recirculation button to the OFF position 2 Push the button in 3 Turn on the fan control dial 4 Move the temperature control lever to the desired position Defrosting or defogging This mode is used to defrost defog the win dows 1 Push the lt 7 button in 2 Turn on the fan control dial 3 Move the temperature control lever to the desired position between the middle and the HOT position e To quickly remove ice or fog from the windows turn on the fan control dial to 4 and the temperature control lever to the full HOT position e When the lt 7 button is pushed the air conditioner will automatically be turned on to defog the windshield and the a
84. This could result in a discharged battery PERSONAL LIGHT Without sunroof 1C1019 B When the interior light or the personal light switch is in the ON position the interior personal vanity mirror and trunk lights will automatically turn off 10 minutes after the ignition switch has been turned to the OFF position To turn on the light again insert the key into the ignition switch and move it to the ON position After the above procedure the interior per sonal vanity mirror or trunk lights will auto matically turn off 10 minutes after the latest operation of the following with the ignition switch in the ACC or OFF position e Opening or closing any door or trunk lid Instruments and controls 2 31 e Locking or unlocking the drivers door e Inserting or removing a key from the ignition switch These lights will turn on again when any of the above operations is performed after the lights have turned off automatically The lights will turn off 10 minutes after the latest operation of the above as well AA CAUTION e Turn off the interior personal and 2 32 Instruments and controls vanity mirror lights when you leave the vehicle Do not use for extended periods of time with the engine stopped This could result in a discharged battery VANITY MIRROR LIGHT if so equipped The light on the vanity mirror will turn on when the cover on the vanity mirror is opened When the inter
85. Universal TWANSCBIVGR ceriose scan EErEE 2 33 Interior and cargo light ee 2 30 Mtaro NONE Sossen oooi 2 30 Interior light replacement 8 27 JUMP Sta NING isione 6 7 Keyless entry See multi remote control system ue KOYS arated ahd avandia de aes L Label Air conditioner specification label 10 12 Label Emission control information label 10 11 Label F M V S S certification label 10 11 Labels Air bag warning labels ee 1 19 Air conditioner specification label 4 3 Engine serial number 0 cc ee 10 11 Vehicle identification number VIN 10 10 License plate Installing front license plate 10 13 Light Air bag warning light 0 0 ee 1 18 Bulb replacement 0 cece eee 8 25 Fog light SWITCH estcsccisccetcteeteneietneccaie kee 2 19 Headlamps Bulb replacement 8 26 Headlight switch 0 2 17 Headlights Bulb replacement 8 26 Interior and cargo light 2 30 Interior MONtri 2 30 Personal hOhitiiinaninnen 2 31 Replacement si cscs cates cae ccatuereawerteettess 8 25 MMMM QIU seoksia cated cciencotecacdeterndicasis 2 33 Vanity mirror light so ccnccccseecernerceenencernercens 2 32 Warning indicator lights and chimes 2 7 2 9 Lights Exterior and interior light NEPlACS MON estourar Salis een catia el 8 27 Loading information See vehicle loading INMONMALOMN cies sassarsersanccaenscrannactarnn
86. WARNING e If done incorrectly jump starting can lead to a battery explosion resulting in severe injury or death It could also damage your vehicle e Explosive hydrogen gas is always present in the vicinity of the battery Keep all sparks and flames away from the battery e Do not allow battery fluid to come into contact with eyes skin cloth or painted surfaces Battery fluid is a corrosive sulphuric acid solution which can cause severe burns If the fluid should come into contact with anything immediately flush the con tacted area with water e Keep battery out of the reach of children In case of emergency 6 7 e The booster battery must be rated at 12 volts Use of an improperly rated battery can damage your vehicle e Whenever working on or near a bat tery always wear suitable eye protec tors for example goggles or indus trial safety spectacles and remove rings metal bands or any other jew elry Do not lean over the battery when jump starting e Do not attempt to jump start a frozen battery It could explode and cause serious injury e Your vehicle has an automatic engine cooling fan It could come on at any time Keep hands and other objects away from it 6 8 In case of emergency ae ae D S Jumper cable connecting order dA Vehicle with_ battery for boo PIP SCE0154A A WARNING Always follow the instructions below Failure to do so could result in
87. WARNING e When returning the seatbacks to the upright position be certain that they are completely secured in the latched position If they are not completely secured in the right position passen gers may be injured in an accident or sudden stop UNLOCK Lock lever T SPA0467 e Never allow anyone to ride in the luggage area or on the rear seat when Lumbar support Drivers seat The lumbar support feature provides lower back support to the driver Move the lever up or down to adjust the seat lumbar area SSS0149 FOLDING REAR SEAT Interior trunk access it is in the fold down position Use of these areas by passengers without proper restraint can be extremely dangerous in an accident or sudden stop Properly secure all cargo to help pre vent it from sliding or shifting Do not place cargo higher than the seat backs In a sudden stop or collision unsecured cargo could cause per The trunk can be readily accessible from the rear seat for loading and unloading as shown sonal injury e Rear seats will not fold when the lock 1 6 Seats restraints and supplemental air bag systems e Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously injured Keep the car locked with the rear seatback securely latched when not in use and prevent children s access to car keys ment after someone else uses the
88. adio r ceptiON issira ara 4 13 FM AM radio with cassette player 4 14 FM AM radio with cassette player and compact disc CD Playetsi iicarci sts eevee naina 4 19 AMMONIA E A 4 24 Car phone or CB radio 00 ee eeeeeeeeeeeeeeeseeeeeeees 4 25 VENTILATORS l CLOSE A OPEN p SAA0373 SAA0374 Adjust the air flow direction of ventilators Open or close and adjust the air flow direction of ventilators X This symbol indicates that the vents are closed when the vent switch is moved to the left Ml This symbol indicates that the vents are open when the vent switch is moved to the right 4 2 Heater air conditioner and audio systems Air flow control buttons Fan control dial i Air recirculation button Temperature control lever HEATER AND AIR CONDITIONER Manual Air conditioning button SAA0383 WARNING e The air conditioner cooling function operates only when the engine is run ning Do not leave children impaired adults or pets alone in your vehicle On hot sunny days temperatures in a closed vehicle could quickly be come high enough to cause severe or possibly fatal injuries to people or animals Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up Positioning of the heating or air con ditioning controls should not be done while driving so full attention may be giv
89. ality Radio reception Your radio system is equipped with state of the art electronic circuits to enhance radio reception These circuits are designed to ex tend reception range and to enhance the quality of that reception However there are some general characteris tics of both FM and AM radio signals that can affect radio reception quality in a moving ve hicle even when the finest equipment is used These characteristics are completely normal in a given reception area and do not indicate any malfunction in your radio system Remember that a moving vehicle is not the ideal place to listen to a radio Because of the movement reception conditions will constantly 4 12 Heater air conditioner and audio systems change Buildings terrain signal distance and interference from other vehicles can work against ideal reception Described below are some of the factors that can affect your radio reception MAXIMUM SIGNAL DISTANCES n ayo _ oS See N aie Jd AA e FM 25 to 30 mile 40 to 48 km e AM 60 to 130 mile 97 to 209 km A SAA0306 FM RADIO RECEPTION Range FM range is normally limited to 25 to 30 miles 40 to 48 km with monaural single channel FM having slightly more range than stereo FM External influences may some times interfere with FM station reception even if the FM station is within 25 miles 40 km The strength of the FM signal is directly related to the distance between the transmitter a
90. another vehicle depress the accelerator pedal When you release the pedal the vehicle will return to the previ ously set speed e The vehicle may not maintain the set speed when going up or down steep hills If this happens drive without the cruise control To cancel the preset speed follow either of these three methods a Push the cancel switch The SET indicator light will go out b Tap the brake pedal The SET indicator light will go out c Turn the main switch off Both the CRUISE indicator and SET indicator lights will go out e f you depress the brake pedal while push ing the RES ACCEL set switch and reset at the cruising speed turn the main switch off once and then turn it on again e The cruise control will automatically be can celled if the vehicle slows down below approximately 8 MPH 13 km h e Depress the clutch pedal manual transmis sion or move the selector lever to N Neu tral position automatic transmission The SET indicator light will go out To reset at a faster cruising speed use one of the following three methods a Depress the accelerator pedal When the vehicle attains the desired speed push and release the COAST SET switch b Push and hold the RES ACCEL set switch When the vehicle attains the speed you desire release the switch c Push then quickly release the RES ACCEL set switch Each time you do this the set speed will increase by about 1 MPH 1 6 km h T
91. anufacturer e Donotuse glass or plastic cleaner on meter or gauge lens covers It may damage the lens cover FLOOR MATS The use of Genuine Nissan floor mats can extend the life of your vehicle carpet and make it easier to clean the interior No matter what mats are used be sure they are fitted for your vehicle and are properly positioned in the footwell to prevent interference with pedal operation Mats should be maintained with regular cleaning and replaced if they become excessively worn Floor mat bracket Floor mat positioning aid Driver side only This model includes a front floor mat bracket to act as a floor mat positioning aid NISSAN floor mats have been specially designed for your vehicle model The driver s side floor mat has a grommet hole incorporated in it Simply position the mat by placing the floor mat bracket through the floor mat grommet hole while centering the mat in the floorpan contour Periodically check to make certain that the mats are properly positioned SEAT BELTS The seat belts can be cleaned by wiping them with a sponge dampened in a mild soap solu tion Allow the belts to dry completely before using them WARNING Do not allow wet belts to roll up in the retractor NEVER use bleach dye or chemical solvents since these may se verely weaken the seat belt webbing CORROSION PROTECTION MOST COMMON FACTORS CONTRIBUTING TO VEHICLE CORROSION e The accumulation of
92. ape loaded the tape will be ejected When the tape is ejected while it is being played the system will be turned off Compact disc CD player operation AA CAUTION e During cold weather or rainy days the player may malfunction due to the humidity If this occurs remove the CD and dehumidify or ventilate the player completely e The player may skip while driving on rough roads e The CD player sometimes cannot function when the compartment tem perature is extremely high Decrease the temperature before use e Do not expose the CD to direct sun light e CDs that are of poor quality dirty scratched or covered with finger prints may not work properly e Donotusean8 amp cm CD adapter as this will cause malfunction e Recordable compact discs CD R may not function properly in the CD player Turn the ignition key to the ACC or ON position and insert the compact disc into the slot with the label side facing up The compact disc will be guided automatically into the slot and start playing After loading the disc the number of tracks on the disc and the play time will appear on the display If the radio or tape is already operating it will automatically turn off and the compact disc will play AA CAUTION Do not force the compact disc into the slot This could damage the player If the system has been turned off while the compact disc was playing pushing the ON OFF VOL control knob will s
93. at belts may not fit them properly The shoulder belt may come too close to the face or neck The lap belt may not fit over their small hip bones In an accident an improperly fitting seat belt could cause serious or fatal injury Always use appropriate child restraints All US states and provinces of Canada require the use of approved child restraints for infants and small children See Child restraints later in this section In addition there are many types of child restraints available for larger children which should be used for maximum protection NISSAN recommends that all preteens and children be restrained in the rear seat if possible According to accident statistics children are safer when properly restrained in the rear seat than in the front seat This is especially important because your vehicle has a supplemental restraint sys tem air bag system for the front passen ger see Supplemental Restraint System earlier in this section for precautions Infants and small children NISSAN recommends that infants and small children be placed in child restraints that com ply with Federal Motor Vehicle Safety Stan dards or Canadian Motor Vehicle Safety Stan dards You should choose a child restraint that fits your vehicle and always follow the manu facturer s instructions for installation and use Larger children Children who are too large for child restraint systems should be seated and restrain
94. at the wipers do not streak Windshield defroster Check that the air comes out of the defroster outlets properly and in good quantity when operating the heater or air conditioner Steering wheel Check for changes in the steering conditions such as excessive free play hard steering or strange noises Seats Check seat position controls such as seat adjusters seatback recliner etc to en sure they operate smoothly and that all latches lock securely in every position Check that the head restraints move up and down smoothly and that the locks if equipped hold securely in all latched positions Seat belts Check that all parts of the seat belt Maintenance 9 3 system for example buckles anchors adjust ers and retractors operate properly and smoothly and are installed securely Check the belt webbing for cuts fraying wear or damage Accelerator pedal Check the pedal for smooth operation and make sure the pedal does not catch or require uneven effort Keep the floor mats away from the pedal Clutch pedal Make sure the pedal operates smoothly and check that it has the proper free play Brakes Check that the brakes do not pull the vehicle to one side when applied Brake pedal and booster Check the pedal for smooth operation and make sure it has the proper distance under it when depressed fully Check the brake booster function Be sure to keep floor mats away from the pedal Parking brake Check that the l
95. ater and air conditioner controls 4 3 Heater and semiautomatic air CONMGILIOMG Assa stented 4 3 Coolant Capacities and recommended fuel UDr CAMS 3 ces sec eerste eee ste aae cg Changing engine coolant 0 ee Checking engine coolant level Corrosion protection 00ccc cece Cruise Control sicccesccc cscccpertacisccacieieaniens Cup ROMO i pirni D Daytime running light system 00 2 19 Defogger switch Rear window and outside mirror Cefogger SWITCH te seen eee neeneeneenee 2 16 Dimensions and weights 0 0cc cee 10 9 Door open warning light 0 eee 2 8 Drive DeliSizscsscid Gti amp aatsrntantiactfen 8 15 Driving Cold weather driving 0 cee 5 21 Driving with automatic transmission 5 8 Driving with manual transmission 5 11 Precautions when starting and driving 5 2 E ECONOMY PUClisc isscccestecsiziec ceseedisueccsierctercocs 5 16 Emission control information label 10 11 Emission control system warranty 04 10 20 Engine Before starting the engine 5 7 Block NG ALCL ariora 5 22 Capacities and recommended fuel IUDNICANNS ctschtece sicraveneev n 10 2 Changing engine coolant 00 ee 8 6 Changing engine Oil ee 8 8 Changing engine oil filter 0 8 9 Checking engine coolant level 0 8 5 Checking engine oil level 0 8 7 Coolant temperature gauge 2 5 Engine compartment check location
96. atest service information through technical bulletins service tips and in dealership training pro grams They are completely qualified to work on NISSAN s vehicles before they work on your vehicle rather than after they have worked on it You can be confident that your NISSAN deal er s service department performs the best job to meet the maintenance requirements on your vehicle in a reliable and economic way GENERAL MAINTENANCE During the normal day to day operation of the vehicle general maintenance should be per formed regularly as prescribed in this section If you detect any unusual sounds vibrations or smell be sure to check for the cause or have your NISSAN dealer do it promptly In addition you should notify your NISSAN dealer if you think that repairs are required When performing any checks or maintenance work see Maintenance precautions in the 8 Do it yourself section EXPLANATION OF MAINTENANCE ITEMS Additional information on the following items with is found in the 8 Do it yourself section Outside the vehicle The maintenance items listed here should be performed from time to time unless otherwise specified Tires Check the pressure with a gauge pe riodically when at a service station including the spare and adjust to the specified pressure if necessary Check carefully for damage cuts or excessive wear Wheel nuts When checking the tires make sure no
97. ation 0 0 ce 5 13 SY SIO its itaves eaten vig i 5 18 Wearingilig htc ission 2 9 Break In schedule eeceeereeeeeeseeeeeteneeeees 5 16 Bulb check instrument panel cee 2 7 Bulb replacement 0c cece sees 8 25 c Capacities and recommended fUeSWMWDICANTS isineun enaa 10 2 Car phone Gar phone 0r CB radio asiiennsanaaniiaa Cassette player See audio system Cassette tape operation eeeeeeeeeeeeeeee Catalytic converter Three way catalyst Child OStrAINtS nrnna en enese Installation on front passenger seat Installation on rear seat outboard or center positions 1 30 Precautions on child restraints wa 1 28 Top tether strap anchor point locations 1 35 Child SALSA kienean 1 22 Child safety rear door lOCK 0 0 cee 3 4 CHIMES vecceseteeseet ctreteevedivslennss lasideneeleeites 2 11 Cigarette lighter accessory and ashtray 2 23 Circuit breaker Fusible link ceeeeeeeee 8 22 Cleaning exterior and interior 00 7 2 7 4 GlOCk erisera sisia eaa ai 2 30 Clutch Cl tch pedal sc iicczesncstiseodsieveneitecteitedns s 8 21 alll Co REER 8 12 Cold weather driving 5 21 Compact Disc CD player See audio SYSIOM E E E 4 23 Compact disc CD player operation 4 12 Compact spare tire 0 8 35 Console DOXA EES 2 26 Controls AUJIO CONOS sisii Audio controls rear 0c eee Audio controls steering wheel i He
98. ay result Tampering with the supplemental in serious personal injury side air bag system may result in serious personal injury Tampering includes changes to the front seats assembly by placing material near the seatback of the front seat or by installing additional trim material around the side air bag system Work around and on the supplemen tal side air bag system should be done by an authorized NISSAN dealer Installation of electrical equip ment should also be done by an au thorized NISSAN dealer The SRS wir ing harnesses should not be modified or disconnected Unautho rized electrical test equipment and probing devices should not be used on the side air bag system The SRS wiring harnesses are cov ered with yellow insulation either just before the harness connectors or over the complete harness for easy identification WARNING e The pre tensioner seat belt cannot be reused after activation It must be replaced together with the retractor as a unit If the vehicle becomes involved in a frontal collision but the pre tensioner is not activated be sure to have the pre tensioner system checked and if necessary replaced by your NISSAN dealer No unauthorized changes should be made to any components or wiring of the pre tensioner seat belt system This is to prevent accidental activa tion of the pre tensioner seat belt or damage to the pre tensioner seat belt an authorized NISSAN dealer Instal
99. ber seal that holds the spark plug so that it will not fall when it is pulled out Make sure that each 8 16 Do it yourself spark plug is snugly fitted into the plug socket Fit the new plugs one at a time into the spark plug socket and install them Turn each plug in several full turns by hand then tighten with a spark plug socket to the correct torque Do not overtighten Spark plug tightening torque 14 to 22 ft lb 20 to 29 N m 6 Holding the ignition coil re connect each ignition coil to its proper spark plug by pushing it on until you feel a snap 7 Tighten all ignition coils Front side Rear side m Platinum tipped SDI0145 AIR CLEANER y S Th H ARE LE Platinum tipped spark plugs It is not necessary to replace the platinum tipped spark plugs as frequently as the con ventional type spark plugs since they will last much longer Follow the maintenance sched ule but do not reuse them by cleaning or regapping Always replace with recommended platinum tipped spark plugs The filter element should not be cleaned and reused Replace it according to the mainte nance intervals See Periodic maintenance schedules in the 9 Maintenance section for maintenance intervals When replacing the filter wipe the inside of the air cleaner housing and the cover with a damp cloth A WARNING e Operating the engine with the air cleaner removed can cause
100. c Automatic transaxle fluid level Check the level on the dipstick after putting the selector lever in P Park position with the engine idling Exhaust system Make sure there are no loose supports cracks or holes If the sound of the exhaust seems unusual or there is a smell of exhaust fumes immediately locate the trouble and correct it See Precautions when starting and driving in the 5 Starting and driving section for exhaust gas carbon mon oxide Underbody The underbody is frequently ex posed to corrosive substances such as those used on icy roads or to control dust It is very important to remove these substances other wise rust will form on the floor pan frame fuel lines and around the exhaust system At the end of winter the underbody should be thor oughly flushed with plain water being careful to clean those areas where mud and dirt may accumulate For additional information see Cleaning exterior in the 7 Appearance and care section Fluid leaks Check under the vehicle for fuel oil water or other fluid leaks after the vehicle has been parked for a while Water dripping from the air conditioner after use is normal If you should notice any leaks or if gasoline fumes are evident check for the cause and have it corrected immediately PERIODIC MAINTENANCE SCHEDULES To ensure smooth trouble free safe and eco nomical driving NISSAN provides two differ ent maintenance sche
101. card in the 10 Technical and consumer information Do not drive your vehicle at speeds faster than 50 MPH 80 km h Do not use tire chains on a T type 8 36 Do it yourself spare tire Tire chains will not fit prop erly on the T type spare tire and may cause damage to the vehicle When driving on roads covered with snow or ice the T type spare tire should be used on the rear wheel and the original tire used on the front wheels drive wheels Use tire chains only on the front two original tires Tire tread of the T type spare tire will wear at a faster rate than the original tire Replace the T type spare tire as soon as the tread wear indicators appear Because the T type spare tire is smaller than the original tire ground clearance is reduced To avoid dam age to the vehicle do not drive over obstacles Also do not drive the ve hicle through an automatic car wash since it may get caught Do not use the T type spare tire on other vehicles Do not use more than one T type spare tire at the same time e Do not tow a trailer while the T type spare tire is installed 9 Maintenance General maintenance eeeeeeseeeeteeeeeeeeereeeees 9 3 SCHOGUIC rriena iaa 9 5 Explanation of maintenance iteMS ccceee 9 3 OChed le 2 erp reaa a eek hte oe 9 5 Periodic maintenance schedules eee 9 5 Explanation of maintenance items 9 10 Your new NISSAN has been designed to have
102. cee 8 12 Window s GIG ANING eset sesh sedctvsetast riin er erases 7 3 Power WINDOWS sci ccieciscsettcdvedeeteddeinedetiee 2 27 Windshield wiper and washer switch 2 15 Wiper BIRdES dararia tiie tite ci T 8 18 Windshield wiper and washer switch 2 15 GAS STATION INFORMATION FUEL RECOMMENDATION Unleaded premium gasoline with an octane rating of at least 91 AKI Anti Knock Index number Research octane number 96 If unleaded premium gasoline is not avail able unleaded regular gasoline with an octane rating of at least 87 AKI Research octane number 91 can be used However for maximum vehicle perfor mance the use of unleaded premium gaso line is recommended AA CAUTION Using a fuel other than that specified could adversely affect the emission con trol systems and may also affect war ranty coverage Under no circumstances should a leaded gasoline be used since this will damage the three way catalyst For additional information see Capacities and recommended fuel lubricants in the 10 Technical and consumer information section ENGINE OIL RECOMMENDATION e API Certification Mark e API grade SG SH Energy Conserving II or API grade SJ Energy Conserving e ILSAC grade GF II e SAE 5W 30 viscosity oil is preferred for all ambient temperatures SAE 10W 30 vis cosity oil may be used for ambient tempera tures above 0 F 18 C See Capacities and recommended fuel l
103. celeration or stops e Avoid sharp turns or lane changes e Always drive your vehicle at a moderate speed e Always block the wheels on both vehicle and trailer when parking Parking on a 10 18 Technical and consumer information slope is not recommended however if you must do so and if your vehicle is equipped with automatic transmission first block the wheels and apply the parking brake and then move the transmission selector lever into the P Park position If you move the selector lever to the P Park position be fore blocking the wheels and applying the parking brake transmission damage could occur When going down a hill shift into a lower gear and use the engine braking effect When ascending a long grade downshift the transmission to a lower gear and reduce speed to reduce chances of engine over loading and or overheating If the engine coolant rises to an extremely high temperature when the air conditioning system is on turn off the air conditioner Coolant heat can be additionally vented by opening the windows switching the fan control to high and setting the temperature control to the HOT position Trailer towing requires more fuel than nor mal circumstances Avoid towing a trailer for the first 500 miles 800 km Have your vehicle serviced more often than at intervals specified in the recommended maintenance schedule When making a turn your trailer wheels will be closer to the inside of t
104. cesses Drive belts ieee Spark PIUGS wi csssccasesgsecdsccsvsverseavschsdedacescusseetenascaeays 8 15 Replacing spark pPlUQS 0 cece ee eee eeeeeeaee 8 16 Air cleaner Windshield wiper blades 0 e eee eee 8 18 GIS ANING ianei ties disuse eae 8 18 REPIACOMONE iicisss asessesascesescdacntoncaslisdivaesesisdesesasnaives 8 19 Parking brake and brake pedal ee 8 20 Checking parking brake ou eee eee eee tees 8 20 Checking brake pedal ciiisean 8 20 Brake DOOSteliiissciisivsavs unni 8 21 Engine compartment eeceeeeseeseeseeeereeeeee 8 22 Passenger compartment e eee eects 8 23 Multi remote controller battery replacement Lights Headlights Exterior and interior lights aseeseen 8 27 Tires and wheelSi csssecaenstaaniinived aed 8 32 Tire pressure TYPOS Of TOS vee iccsdsci cis sactchcectecsseetencanteliseeredoes dertencse 8 32 aN Cee n Uk peeeeteereteeeeerrrerer eererte a a aa a 8 33 Changing tires and wheels 8 34 MAINTENANCE PRECAUTIONS When performing any inspection or mainte nance work on your vehicle always take care to prevent serious accidental injury to yourself or damage to the vehicle The following are general precautions which should be closely observed WARNING e Park the vehicle on a level surface apply the parking brake securely and block the wheels to prevent the ve hicle from moving For a manual transmission move the s
105. ch may lead to an accident Warm the windshield with the defroster before you wash the wind shield CAUTION The following could damage the washer system e Do not operate the washer continu ously for more than 30 seconds e Do not operate the washer if the res ervoir tank is empty Instruments and controls 2 15 REAR WINDOW AND OUTSIDE MIRROR if so equipped DEFOGGER SWITCH Indicator ight CAUTION When cleaning the inner side of the rear window be careful not to scratch or damage the rear window defogger REAR PUSH ON OFF 1C1231 To defog defrost the rear window glass and outside mirrors start the engine and push the switch on The indicator light will come on Push the switch again to turn the defogger off It will automatically turn off in approximately 15 minutes 2 16 Instruments and controls HEADLIGHT AND TURN SIGNAL SWITCH Type A Light switch Headlight beam selector Tum signal Lane change pressing signal switch signal switch AUTO 1st step 2nd step 3rd step Passing signal Type B P Headlight beam selector Turn signal Lane change Light switch pressing signal switch signal switch Low beam AUTO ma 0O 1st step 2nd step 3rd step SIC 1229 HEADLIGHT SWITCH position the tail light headlight instrument Pees light and other lights turn on automatically Lighting depending on the brightness of the surround Turn the switch to the AUTO posi
106. checks and adjustments 2 Keep pushing the UNLOCK button on the multi remote controller or push the button again within 5 seconds e All doors unlock e The hazard indicator flashes once if all doors are completely closed The interior light can be turned off without waiting for 30 seconds by turning the ignition switch to the ON position or by locking the doors with the multi remote controller Releasing the trunk lid 1 Push the trunk button on the multi remote controller for longer than 0 5 second with the key removed from the key cylinder 2 The trunk lid opens The trunk lid will not open when the trunk lid cancel lever is in the CANCEL position It can be opened only with the key See Trunk lid later in this section for cancel lever Using the panic alarm If you are near your vehicle and feel threat ened you may activate the alarm to call atten tion as follows 1 Push the PANIC button on the remote controller for longer than 0 5 seconds The theft warning alarm and headlights will stay on for 30 seconds The panic alarm stops when It has run for 30 seconds or The LOCK or the UNLOCK button is pressed or The panic button is pushed on the multi remote controller for longer than 0 5 sec onds OPEN Suitable tool S 2 side up REMOVE the battery SPA1046 BATTERY REPLACEMENT Replace the battery as follows 1 Open the lid using a suitable tool
107. cle operation Manual fan control button Manual air flow control button ECON button Start the engine and operate the controls to activate the air conditioner AUTOMATIC OPERATION Cooling and or dehumidified heating AUTO This mode may be normally used all year round as the system automatically works to keep a constant temperature Air flow distribu Tempera i perature set dial Air recirculation button AUTO button OFF button SAA0379 ning AA WARNING e Do not leave children impaired e The air conditioner cooling function operates only when the engine is run adults or pets alone in your vehicle tion and fan speed are also controlled auto matically Heater air conditioner and audio systems 4 9 1 Push the AUTO button on AUTO will be displayed 2 Turn the temperature set dial to the left or right to set the desired temperature e Adjust the temperature set dial to about 75 F 24 C for normal operation e The temperature of the passenger compart ment will be maintained automatically Air flow distribution and fan speed are also controlled automatically Heating ECON The air conditioner does not activate When you need to heat only use this mode 1 Push the ECON Economy button on ECON will be displayed 2 Turn the temperature set dial to the left or right to set the desired temperature e The temperature of the passenger compart ment will be maintained automat
108. cle thoroughly using a mild soap such as Nissan Car Wash or a general pur pose dishwashing liquid mixed with clean lukewarm never hot water AA CAUTION e Do not use strong household soap strong chemical detergents gasoline or solvents e Do not wash the vehicle in direct sunlight or while the vehicle body is hot as the surface may become water spotted e Avoid using tight napped or rough cloths such as washing mitts Care must be taken when removing caked on dirt or other foreign sub stances so that the paint surface is not scratched or damaged Rinse the vehicle again with plenty of clean water Inside flanges seams and folds on the doors hatches and hood are particularly vulnerable to the effects of road salt Therefore these areas must be regularly cleaned Make sure that the drain holes in the lower edge of the door are open Spray water under the body and in the wheel wells to loosen the dirt and wash away road salt Avoid leaving water spots on the paint surface by using a damp chamois to dry the vehicle WAXING Regular waxing protects the paint surface and helps retain new vehicle appearance After waxing polishing is recommended to remove built up residue and to avoid a weathered appearance If you wish to wax your vehicle only use a wax specified for use over clear coats such as Nissan Liquid or Spray Wax Your Nissan dealer can assist you in choosing the proper product e Wax your vehic
109. control system malfunction has been detected Check the fuel filler cap If the fuel filler cap is loose or missing tighten or install the cap and continue to drive the vehicle The ANF lamp should turn off after a few driving trips If the x8KF lamp does not turn off after a few driving trips have the vehicle inspected by an authorized NISSAN dealer You do not need to have your vehicle towed to the dealer Malfunction indicator lamp blinking An engine misfire has been detected which may damage the emission control system To reduce or avoid emission control system damage a Do not drive at speeds above 45 MPH 72 km h b Avoid hard acceleration or deceleration c Avoid steep uphill grades d If possible reduce the amount of cargo being hauled or towed The malfunction indicator lamp may stop blinking and come on steady Have the vehicle inspected by an autho rized NISSAN dealer You do not need to have your vehicle towed to the dealer fA CAUTION Continued vehicle operation without having the emission control system checked and repaired as necessary could lead to poor driveability reduced fuel economy and possible damage to the emission control system TCS Traction control system OFF indicator light if so equipped The traction control system indicator light should come on when you turn the ignition key to ON The light will go off as you start the engine If the indicator light does n
110. d e Never leave children unattended in the vehicle Firmly apply the parking brake 2 Automatic transmission models Move the selector lever to the P Park position Manual transmission models Place the shift lever in the R Reverse position When parking on an uphill grade place the shift lever in the 1 Low gear position AA WARNING e Safe parking procedures require that both the parking brake be set and the transmission placed into P Park for automatic transmission models or in an appropriate gear for manual trans mission models Failure to do so could cause the vehicle to move un expectedly or roll away and result in an accident e Make sure the automatic transmis sion selector lever has been pushed as far forward as it can go and cannot be moved without depressing the button at the end of the lever 3 To help prevent the vehicle from rolling into the street when parked on a sloping drive way it is a good practice to turn the wheels as illustrated HEADED DOWNHILL WITH CURB Turn the wheels into the curb and move the vehicle forward until the curb side wheel gently touches the curb Starting and driving 5 17 e HEADED UPHILL WITH CURB Turn the wheels away from the curb and move the vehicle back until the curb side wheel gently touches the curb e HEADED UPHILL OR DOWNHILL NO CURB Turn the wheels toward the side of the road so the vehicle will move away from the cen
111. d NISSAN dealer or contact Dyment Distribution Services 20770 Westwood Dr Strongsville OH 44136 1 800 247 5321 In Canada To purchase a copy of a genuine NISSAN Service Manual or Owners Manual please contact your nearest NISSAN dealer For the phone number and location of a NISSAN Dealer in your area call the NISSAN Satisfac tion Center at 1 800 387 0122 and a bilingual NISSAN representative will assist you Also available are Genuine NISSAN Service and Owner s Manuals for older NISSAN mod els 11 Index A ABS Anti lock brake system 0 ee 5 19 Air bag Warming labels nininini A 1 18 Warning light 0 cccs cccncceneecenetcees 1 19 2 8 Air bag system See supplemental restraint system 1 13 Side See supplemental side air bag Syste Minnan a nenveasiventiaveas 1 15 Air cleaner housing filter c ceeee 8 17 Air conditioner Air conditioner operation 43 Air conditioner service Air conditioner specification label 4 3 10 12 Air conditioner system refrigerant and lubrication recommendations c 4 3 Heater and air conditioner controls 4 3 Servicing air conditioner 4 3 Air conditioning system refrigerant and lubricant FECOMIMENGALIONS we cee cccees vec oe cde eee cares dar c 10 6 Air TOW CHANTS i se cczes xen tere enia ae 4 6 Alcohol drugs and driving sssr sirsenis 5 4 AM FM radio with cassette player 0
112. d This will occur even if all electrical circuits are functioning properly In this case turn the ignition key OFF and wait for 3 seconds Then turn the key back to the ON position The vehicle should return to its normal operating con dition If it does not return to its normal operating condition have your NISSAN dealer check the transmission and repair if necessary i 2 SSD0002 MANUAL TRANSMISSION Shifting To change gears or when up shifting or down shifting depress the clutch pedal fully shift into the appropriate gear then release the clutch slowly and smoothly On the five speed transmission model you cannot shift directly from fifth gear into the R Reverse position First shift into the N Neu tral position then into the R Reverse posi tion If it is difficult to move the shift lever into R Reverse or 1 Low gear shift into N Neu Starting and driving 5 11 tral then release the clutch pedal and shift into R Reverse or 1 Low gear again AA WARNING e Donot downshift abruptly on slippery roads This may cause a loss of con trol e Do not over rev the engine when shifting to a lower gear This may cause a loss of control or engine damage AA CAUTION e Do not rest your foot on the clutch pedal while driving This may cause clutch damage e Stop your vehicle completely before shifting into R Reverse e When the vehicle is stopped for a period of time for example at a
113. d smooth operation Shown on the following pages are the recom mended operating procedures for this trans mission Follow these procedures for maxi mum vehicle performance and driving enjoyment Starting the vehicle After starting the engine fully depress the foot brake pedal and push the selector lever button before shifting the selector lever to the R N D 2 or 1 position Be sure the vehicle is fully stopped before attempting to shift the selector lever This automatic transmission is designed so that the foot brake pedal must be de pressed before shifting from P Park posi tion to any drive position while the ignition switch is ON The selector lever cannot be moved out of P Park position and into any of the other gear positions if the key is removed from the switch 1 Keep the foot brake pedal depressed and 5 8 Starting and driving shift into a driving gear 2 Release the parking brake and foot brake then gradually start the vehicle in motion AA WARNING e Do not depress the accelerator pedal while shifting from P or N to R D 2 or 1 Always depress the brake pedal until shifting is completed Failure to do so could cause you to lose control and have an accident e Cold engine idle speed is high so use caution when shifting into a forward or reverse gear before the engine has warmed up e On slippery roads do not downshift This may cause a loss of control e Never shift to P or R while v
114. d before the engine is started the daytime running lights do not illuminate The daytime running lights illu minate once the parking brake is released The daytime running lights will remain on until the ignition switch is turned off AA WARNING When the daytime running light system is active tail lights on your vehicle are not on It is necessary at dusk to turn on your headlights Failure to do so could cause an accident injuring yourself and others TURN SIGNAL SWITCH Turn signal Move the lever up or down to signal the turning direction When the turn is completed the turn signals cancel automatically Lane change signal To indicate a lane change move the lever up or down to the point where lights begin flash ing FOG LIGHT SWITCH if so equipped TURN ON SIC0880 To turn the fog lights on turn the headlight switch to the g position then turn the switch to the 4p position To turn them off turn the switch to the OFF position The headlights must be on for the fog lights to operate Instruments and controls 2 19 HAZARD WARNING FLASHER SWITCH 1C1232 Push the switch on to warn other drivers when you must stop or park under emergency con ditions All turn signal lights will flash Some state laws may prohibit the use of the hazard warning flasher switch while driv ing WARNING e If stopping for an emergency be sure to move the vehicle well off the road 2 20 Instru
115. d driving 5 5 To lock the steering wheel turn the key to the LOCK position Remove the key To unlock the steering wheel insert the key and turn it gently while rotating the steer ing wheel slightly right and left WARNING Never remove or turn the key to the LOCK position while driving The steer ing wheel will lock This may cause the driver to lose control of the vehicle and could result in serious vehicle damage or personal injury 5 6 Starting and driving KEY POSITIONS The switch includes an anti theft steering lock device LOCK Normal parking position 0 The ignition key can only be removed when the switch is in this position OFF 1 The engine can be turned off without locking the steering wheel ACC Accessories 2 This position activates electrical accessories such as the radio when the engine is not running ON Normal operating position 3 This position turns on the ignition system and the electrical accessories START 4 This position activates the starter motor start ing the engine NISSAN VEHICLE IMMOBILIZER SYSTEM The Nissan Vehicle Immobilizer System will not allow the engine to start without the use of the registered Nissan Vehicle Immobilizer Sys tem key If the engine fails to start using the registered Nissan Vehicle Immobilizer System key it may be due to interference caused by another Nissan Vehicle Immobilizer System key an automated toll road device or au
116. d use of the power windows e Do not leave children unattended in side the vehicle They could unknow ingly activate switches or controls and become trapped in a window Unattended children could become involved in serious accidents The power windows operate when the ignition key is in the ON position and for about 45 seconds after the ignition key is turned to the OFF position If the driver s door or the front passenger s door is opened during this period of about 45 seconds power to the windows is canceled To open or close the window push down or pull up the switch and hold it The main switch driver side switches will open or close all the windows Instruments and controls 2 27 Passenger switch TN OPEN A SIC0627B OPEN close me ut Automatically open SPA0980 The passenger side switch will open or close only the corresponding window To open or close the window hold the switch down or up Locking passenger s windows When the lock button is pushed in only the driver side window can be opened or closed Push it in again to cancel 2 28 Instruments and controls Automatic operation To fully open or close the driver s side window completely press or lift the switch and release it it need not be held The window will auto matically open or close all the way To stop the window just press the switch on the opposite side Auto reverse function For driver
117. d where applicable on the tire sidewall between tread shoulder and maximum section width For example Treadwear 200 Traction AA Temperature A Treadwear Treadwear grade is a comparative rating based on tire wear rate when tested under controlled conditions on specified government test courses For example a tire graded 150 would wear one and a half 1 1 2 times as well on the government course as a tire graded 100 However relative tire performance de pends on actual driving conditions and may vary significantly from the norm due to varia tions in driving habits service practices and differences in road characteristics and climate Traction AA A B and C The traction grades from highest to lowest are AA A B and C Those grades represent the tire s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete A tire marked C may have poor traction performance AA WARNING The traction grade assigned to your ve hicle tires is based on straight ahead braking traction tests and does not in clude acceleration cornering hydro planing or peak traction characteristics Temperature A B and C Temperature grades are A the highest B and C They represent a tire s resistance to heat build up and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel Sus tained high temperatur
118. deral and or local regulations When wiring the vehicle for towing connect the stop and tail light pickup into the vehicle electrical circuit at a point between the sensor and stop light or light switch Trailer brakes If your trailer is equipped with a braking sys tem make sure it conforms to federal and or local regulations and that it is properly in stalled WARNING Never connect a trailer brake system directly to the vehicle brake system Pre towing tips e Be certain your vehicle maintains a level position when a loaded and or unloaded Technical and consumer information 10 17 trailer is hitched Do not drive the vehicle if it has an abnormal nose up or nose down condition check for improper tongue load overload worn suspension or other pos sible causes of either condition e Always secure items in the trailer to prevent load shifts while driving e Becertain your rear view mirrors conform to all federal state or local regulations If not install any mirrors required for towing be fore driving the vehicle Trailer towing tips In order to gain skill and an understanding of the vehicle s behavior you should practice turning stopping and backing up in an area which is free from traffic Steering stability and braking performance will be somewhat differ ent than under normal driving conditions e Always secure items in the trailer to prevent load shift while driving e Avoid abrupt starts ac
119. djust BASS TREB FADER BAL Bass Treble Fader Balance press the AUDIO button until the desired mode BAS TRE FAD or BAL appears in the display Press the y or A button to adjust BASS and TREB to the desired level Use the wz or A button to adjust FADER or BAL modes FADER adjusts the sound level be tween the front and rear speakers and BAL adjusts the sound level between the right and left speakers After 10 seconds the radio or cassette tape display reappears Once the sound quality is set to the desired level press the AUDIO button repeatedly until the radio or cassette tape display appears Radio Cassette tape priority mode In this mode the radio station illuminates in the display during radio operation During cassette tape operation TAPE illuminates in the dis play FM AM radio operation err FM AM band select Push the FM AM band select button to listen to the radio and tune in the desired station Pushing the FM AM band select button will change the band FM1 FM2 or AM The FM stereo indicator ST illuminates during FM stereo reception When the stereo broad cast signal is weak the radio automatically changes from stereo to monaural reception VY AX TUNE Tuning WARNING The radio should not be tuned while driving so full attention may be given to vehicle operation Push either manual tuning button wy or AN s Z SEEK SCAN tuning Push the SEE
120. dules that may be used depending upon the conditions in which you usually drive These schedules contain both distance and time intervals up to 60 000 miles 96 000 km 48 months For most people the odometer reading will indicate when service is needed However if you drive very little your vehicle should be serviced at the regular time intervals shown in the schedule After 60 000 miles 96 000 km or 48 months continue the periodic maintenance at the same mileage time intervals SCHEDULE 1 Follow Periodic Maintenance Schedule 1 if your driving habits frequently include one or more of the following driving conditions e repeated short trips of less than 5 miles 8 km e repeated short trips of less than 10 miles 16 km with outside temperatures re maining below freezing e operating in hot weather in stop and go rush hour traffic e extensive idling and or low speed driv ing for long distances such as police taxi or door to door delivery use e driving in dusty conditions e driving on rough muddy or salt spread roads e towing a trailer using a camper or a car top carrier SCHEDULE 2 Follow Periodic Maintenance Schedule 2 if none of the driving conditions shown in Sched ule 1 apply to your driving habits Maintenance 9 5 Schedule 1 Abbreviations R Replace Inspect Correct or replace if necessary At the mileage intervals only MAINTENANCE OPERATION MAINTENANCE IN
121. duplicated by your NISSAN dealer Nissan Vehicle Immobilizer System KEY Master and Security keys The key number is necessary when you need extra Nissan Vehicle Immobilizer System keys As many as 5 Nissan Vehicle Immobi lizer System keys can be used with one ve hicle New keys must be registered to the Nissan Vehicle Immobilizer System compo nents in your vehicle by your NISSAN dealer At this time you should bring all Nissan Ve hicle Immobilizer System keys that you have to your NISSAN dealer for registration This is because the registration process will erase all memory of the Nissan Vehicle Immobilizer System components DOORS A WARNING e Always have the doors locked while driving Along with the use of seat belts this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle This also helps keep children and others from unintention ally opening the doors and will help keep out intruders Before opening any door always look for and avoid oncoming traffic Do not leave children unattended in side the vehicle They could unknow ingly activate switches or controls Unattended children could become involved in serious accidents LOCK PN Cy UNLOCK lt j Front SPA0084 SPA0085 Front passenger s side Fi Lock i UNLOCK SPA0944 LOCKING WITH KEY Power The power door lock system allows you to lock or un
122. e your vehicle may be damaged and or vehicle handling and perfor mance may be adversely affected Never install tire chains on a T type spare tire Do not use the chains on dry roads Do it yourself 8 33 Front fo HY 4 wheels DI0048 B CHANGING TIRES AND WHEELS Tire rotation NISSAN recommends that tires be rotated every 7 500 miles 12 000 km Wheel nut tightening torque 72 to 87 ft lb 98 to 118 N m See Flat tire in the 6 In case of emergency section for tire replacing procedures 8 34 Do it yourself WARNING e After rotating the tires adjust the tire pressure e Retighten the wheel nuts when the vehicle has been driven for 600 miles 1 000 km also in cases of a flat tire etc e Do not include the T type spare tire or any other small size spare tire in the tire rotation Wear indicator Location mark MDI0004 Tire wear and damage AA WARNING Tires should be periodically inspected for wear cracking bulging or objects caught in the tread If excessive wear cracks bulging or deep cuts are found the tire should be replaced The original tires have a built in tread wear indicator When the wear indicator is visible the tire should be replaced Improper service for a T type spare tire may result in serious personal injury If it is necessary to repair the T type spare tire contact your NISSAN dealer Replacing tires and wheels When re
123. e can cause tire mate rial to degenerate reducing tire life Excessive temperatures can lead to sudden tire failure Grade C corresponds to a performance level which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No 109 Grades A and B represent higher levels of performance on laboratory test wheels than the minimum required by law Technical and consumer information 10 19 WARNING The temperature grade for this tire is established for a tire that is properly inflated and not overloaded Excessive speed underinflation or excessive loading either separately or in combina tion can cause heat buildup and pos sible tire failure 10 20 Technical and consumer information EMISSION CONTROL SYSTEM WARRANTY Your NISSAN is covered by the following emission warranties For US e Emission Defects Warranty e Emissions Performance Warranty For Canada Emission Control System Warranty Details of these warranties may be found with other vehicle warranties in your Warranty In formation and Maintenance Log Booklet that comes with your NISSAN If you did not re ceive a Warranty Information and Mainte nance Log Booklet or it has become lost you may obtain a replacement by writing to e Nissan North America Inc Consumer Affairs Department P O Box 191 Gardena CA 90248 0191 e Nissan Canada Inc 5290 Orbitor Drive Mississauga Ontario L4W 4Z5 REPORTING SAFETY DEFECTS US only
124. e maximum front and rear GAWRs If you do parts on your vehicle can break or it can change the way your vehicle handles This could result in loss of control TOWING A TRAILER and cause personal injury Overloading can shorten the life of Total trailer load Tongue load your vehicle Failures caused by I overloading are not covered by your i warranty _ load a x 100 9 to 11 Total trailer load TI1011M Your new vehicle was designed to be used primarily to carry passengers and cargo Re member that towing a trailer will place addi tional loads on your vehicle s engine drive train steering braking and other systems Information on trailer towing ability and the special equipment required should be ob tained from your Nissan dealer He can obtain a Nissan Trailer Towing Guide for you Technical and consumer information 10 15 MAXIMUM LOAD LIMITS Maximum trailer loads Never allow the total trailer load to exceed 1 000 Ib 454 kg The total trailer load equals trailer weight plus its cargo weight Towing loads greater than 1 000 Ib 454 kg or using improper towing equipment could adversely affect vehicle handling braking and perfor mance The ability of your vehicle to tow a trailer is not only related to the maximum trailer loads but also the places you plan to tow Tow weights appropriate for level highway driving may have to be reduced on very steep grades or in low traction
125. e night position will reduce glare from the headlights of vehicles behind you at night WARNING Use the night position only when neces sary because it reduces rear view clar ity OUTSIDE MIRRORS WARNING Objects viewed in the outside mirror on the passenger side are closer than they appear Be careful when moving to the right Using only this mirror could cause an accident Use inside mirror or glance over your shoulder to properly judge distances to other objects The outside mirror will operate only when the ignition switch is in the ACC or ON position Turn the control knob to right or left to select the right or left outside mirror then adjust Pre driving checks and adjustments 3 13 MPA0008 Foldable outside mirrors Push the outside mirror backward to fold it 3 14 Pre driving checks and adjustments 4 Heater air conditioner and audio systems VGntilatOrs rosiner iiser rrara aiiai 4 2 Heater and air conditioner Manual ee 4 3 COMMONS olores enean i E ia Heater operation Air conditioner operation Aif TOW CHANTS wes cca ccavecestsecessieag cetcesste annin onasi Heater and air conditioner Automatic if so equipped Automatic operation Manual Operatore ee Ambient temperature switch AMB 4 11 Operating Upsista riiai 4 11 Servicing air Conditioner ee eects 4 11 Audio system FMiradio roco pthonera n a A 4 12 AM r
126. e nut may occur 4 Insert grommets into the hole on the fascia 5 Insert a flat blade screwdriver into the grommet hole to add 90 turn onto the part 6 Insert a J nut into the license plate bracket Technical and consumer information 10 13 before placing the license plate bracket on the fascia 7 Install the license plate bracket with screws 8 Install the license plate with bolts that are no longer than 0 55 in 14 mm 10 14 Technical and consumer information VEHICLE LOADING INFORMATION WARNING e It is extremely dangerous to ride in a cargo area inside of a vehicle In a collision people riding in these areas are more likely to be seriously injured or killed e Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts e Be sure everyone in your vehicle is in a seat and using a seat belt properly TERMS It is important to familiarize yourself with the following terms before loading your vehicle e Curb Weight actual weight of your vehicle vehicle weight including standard and optional equipment fluids emergency tools and spare tire assembly This weight does not include passengers and cargo e GVW Gross Vehicle Weight curb weight plus the combined weight of passengers and cargo e GVWR Gross Vehicle Weight Rating maximum total weight load limit specified for the vehicle e GAWR Gross Axle Weight Rating maxi mum weig
127. e system will not operate at speeds below 3 to 6 MPH 5 to 10 km h to completely stop the vehicle The speeds will vary according to road conditions When the anti lock system senses that one or more wheels are close to locking up the actuator under the hood rapidly applies and releases hydraulic pressure like pumping the brakes very quickly While the actuator is working you may feel a pulsation in the brake pedal and hear a noise or vibration from the actuator under the hood This is normal and indicates that the anti lock system is working properly However the pulsation may indicate that road conditions are hazardous and extra care is required while driving Self test feature The anti lock brake system consists of elec tronic sensors electric pumps and hydraulic solenoids controlled by a computer The com puter has a built in diagnostic feature that tests the system each time you start the engine and move the vehicle at a low speed in forward or reverse When the self test occurs you may hear a clunk noise and or feel a pulsation in the brake pedal This is normal and is not an indication of any malfunction If the computer senses any malfunction it switches the anti lock brake system OFF and turns on the ABS warning light in the dashboard The brake system will then behave normally but without anti lock assistance If the light comes on during the self check or while you are driving you should take your vehicl
128. e to your NISSAN dealer for repair at your earliest convenience WARNING The anti lock brake system is a sophis ticated device but it cannot prevent ac Starting and driving 5 19 cidents resulting from careless or dan gerous driving techniques It can help maintain vehicle control during braking on slippery surfaces but remember that the stopping distance on slippery sur faces will be longer than on normal surfaces even with the anti lock sys tem Stopping distances may also be longer on rough gravel or snow covered roads or if you are using tire chains Always maintain a safe distance from the vehicle in front of you Ultimately the responsibility for safety of self and others rests in the hands of the driver Tire type and condition of tires may also affect braking effectiveness e When replacing tires install the specified size of tires on all four wheels e When installing a spare tire make sure it is the proper size and type as specified on the tire placard See Ve hicle identification in the 10 Tech nical and consumer information sec tion for tire placard location 5 20 Starting and driving TRACTION CONTROL SYSTEM if so equipped On slippery surfaces such as wet asphalt roads vehicle wheels may spin when the vehicle is accelerated This wheel spin re duces acceleration or causes the vehicle to swerve thus decreasing vehicle stability The traction control system helps limit w
129. ecd einen caseneverssavessteansas Warning lights Indicator lights CHIMES iiir Security systems Theft warning if so equipped ee 2 12 Nissan Vehicle Immobilizer System 00 2 13 Windshield wiper and washer switch 00 2 15 Rear window and outside mirror if so equipped GETOGGEK SWITCN cc ce2 ss5sgccteeasasscesesicsert deisescthajessctise 2 16 Headlight and turn signal switch 2 17 Headlight Switsers tierce 2 17 Turn Signal SwitCh arisia ireira 2 19 Fog light switch if so equipped ee 2 19 Hazard warning flasher sWitch 0 0 eee 2 20 HOLM irao aaa cava es 2 20 Heated seats if so equipped ee 2 21 Traction control system TCS cancel switch if SO GQUPPEd 2 s ccescineseicossnsorsessnsacisceetavecianecnaines 2 22 Power Outlet vic ccctcsascsteestepicischenveesessctdeetiien wadedtis 2 22 Cigarette lighter and ashtray accessory 2 23 SlOAGG e E E E T 2 23 RAYS orner cust cave er N a E ET 2 23 GlAaSSOS CAS Griinari aiei 2 24 Cup HOld E isana 2 24 GIOVE DOX siros isisi civ siehe ees te Basch aisia 2 25 Console BOX scsi dsseicessiceectiieeteeeti hn teeaioes eeieeeees 2 26 Luggage net if so equipped eee 2 26 WINGOWS 5 sn cisccsiccsssieicsssssecetcavaadeatnsdbousieesstiveniier chines 2 27 Power WINGOWS 22 2 805i inch sceosisseseusipseeicoestandcienaccatzes 2 27 Sunroof if SO equipped ee eee eee eeeeeteeeeteee 2 2
130. ed by the seat belts which are provided If the child s seating position has a shoulder belt that fits close to the face or neck the use of a booster seat commercially available may help overcome this The booster seat should raise the child so that the shoulder belt is properly positioned across the top middle portion of the shoulder and the lap belt is low on the hips The booster seat should fit the vehicle seat and have a label certifying that it complies with Federal Motor Vehicle Safety Standards or Canadian Motor Vehicle Safety Standards Once the child has grown so the shoulder belt is no longer on or near the face and neck use the shoulder belt without the booster seat WARNING Never let a child stand or kneel on any seat and do not allow a child in the cargo areas while the vehicle is moving The child could be seriously injured or killed in an accident or a sudden stop PREGNANT WOMEN NISSAN recommends that pregnant women Seats restraints and supplemental air bag systems 1 23 use seat belts The seat belt should be worn snug and always position the lap belt as low as possible around the hips not the waist Place the shoulder belt over your shoulder and across your chest Never run the lap shoulder belt over your abdominal area Contact your doctor for specific recommendations INJURED PERSONS NISSAN recommends that injured persons use seat belts depending on the injury Check with your doctor for s
131. eeeeeeeeeeeeteeeeeeeeee 5 10 Shifting Automatic transmission 0 00c ee 5 8 Manual transmission c ceeeeeereeeee 5 11 Shoulder belt height adjustment For front SOS ies a sales uaneieneea mene unaseeleas 1 27 Side air bag system See supplemental side air PAGES SION aona e 1 16 Spark plugs 8 15 Speedometer 2 4 Starting Before starting the engine 5 7 JUMP StA asein isa 6 7 Precautions when starting and driving 5 2 P shstaring se caranya tnra 6 9 Starting the engine cece 5 7 Steering Power steering fluid 0 0 eee 8 11 Power steering system c eee 5 18 Tilting steering wheel ee 3 12 Storage eeii ei Sun shade Sun visors a Sunroof Automatic sunroof ee 2 29 Supplemental air bag system 1 14 Supplemental air bag warning labels 1 18 Supplemental air bag warning light 1 19 2 8 Supplemental restraint system ee 1 8 Precautions on supplemental restraint SYSTEM asorar earn eian S nisani 1 8 Supplemental side air bag system 1 16 Switch Fog light switch 2 19 Hazard warning flasher switch 2 20 Headlight Switi ssania 2 17 Igniti ON SWC hissziarirninssiigicopsnasei 5 4 Ignition switch automatic transmission MOJ IS iaiia oeseri iioii 5 4 Ignition switch manual transmission IMOCEl Sisal vate aie Overdrive switch Power door lock switch Rear window and outside mirror defogger SWILE e aa
132. ehicle e After adjustment gently rock in the seat to make sure it is securely locked SS0133 A WARNING e For most effective protection when the vehicle is in motion the seat e Do not ride in a moving vehicle when should be upright Always sit well the seatback is reclined This can be peck in te Seat and Adjust ihe seat dangerous The shoulder belt will not belt properly See Precautions on be against your body In an accident seat belt usage later in this section you could be thrown into it and re ceive neck or other serious injuries You could also slide under the lap belt and receive serious internal injuries 1 2 Seats restraints and supplemental air bag systems Forward and backward Driver s seat Reclining TURN to adust SPA0097 SPAO099A Forward and backward Pull the lever up while you slide the seat forward or backward to the desired position Release the lever to lock the seat in position Reclining Seat lifter Driver s seat To recline the seatback pull the lever up and Turn either dial to adjust the angle and height lean back To bring the seatback forward ofthe seat cushion to the desired position again pull the lever and move your body forward The seatback moves forward Seats restraints and supplemental air bag systems 1 3 Driver s seat T SPA0467 Lumbar support Drivers seat The lumbar support feature provides lower back sup
133. ehicle is moving This could cause an acci dent CAUTION When stopping the vehicle on an uphill grade do not hold the vehicle by de pressing the accelerator pedal The foot brakes should be used for this purpose D1003M Shifting Push the button to shift into P R or from D to 2 All other positions can be selected without pushing the button P Park Use this selector position when the vehicle is parked or when starting the engine Always be sure the vehicle is at a complete stop For maximum safety depress the brake pedal then push in the select lever button and move the lever to the P Park position Apply the parking brake When parking on a hill apply the parking brake first then shift the lever into the P Park position R Reverse Use this position to back up Always be sure the vehicle is completely stopped With the brake pedal depressed push in the select lever button and move the lever to the R Reverse position N Neutral Neither forward nor reverse gear is engaged The engine can be started in this position You may shift to N Neutral position and restart a stalled engine while the vehicle is moving D Drive Use this position for all normal forward driving 2 Second gear Use for hill climbing or engine braking on downhill grades Do not exceed 69 MPH 110 km h in the 2 Second gear position 1 Low gear Use this position when climbing steep hills sl
134. emperature control to maximum hot and fan control to high speed If engine overheating is caused by climbing a long hill on a hot day run the engine ata fast idle approximately 1 500 rpm until the temperature gauge indication returns to normal Get out of the vehicle Look and listen for steam or coolant escaping from the radiator before opening the hood Wait until no steam or coolant can be seen before pro ceeding 5 Open the engine hood AA WARNING If steam or water is coming from the engine stand clear to prevent getting burned 6 Visually check if the cooling fan is running The radiator hoses and radiator should not leak water If coolant is leaking or the cooling fan does not run stop the engine A WARNING e Be careful not to allow your hands hair jewelry or clothing to come into contact with or to get caught in the cooling fan or drive belt e The engine cooling fan can start at any time when the coolant tempera ture is high 7 After the engine cools down check the coolant level in the reservoir tank with the engine running Add coolant to the reservoir tank if necessary Have your vehicle re paired at the nearest NISSAN dealer TOWING YOUR VEHICLE When towing your vehicle all State Provincial in Canada and local regulations for towing must be followed Incorrect towing equipment could damage your vehicle Towing instruc tions are available from your NISSAN dealer Local
135. en to vehicle operation CONTROLS Fan control dial This dial turns the fan on and off and controls fan speed Air flow control buttons These buttons allow you to select the air flow outlets z Air flows from center and side venti lators lt 7 Air flows from center and side venti lators and foot outlets a Air flows mainly from foot outlets 2 Air flows from defroster outlets and foot outlets Gy Air flows mainly from defroster out lets Temperature control lever This lever allows you to adjust the temperature of the outlet air Heater air conditioner and audio systems 4 3 Air recirculation button OFF position Outside air is drawn into the passenger com partment Use the off position for normal heater or air conditioner operation ON position Indicator light ON Interior air is recirculated inside the vehicle Push the air recirculation button to the ON position when driving on a dusty road or to avoid traffic fumes and for maximum cooling when using the air conditioner Air conditioning button This button is provided only for vehicles with air conditioner Start the engine move the fan control dial to the desired 1 to 4 position and push the air conditioning button to turn on the air condi tioner The indicator light will come on when the air conditioner is on To stop the air con ditioner push the switch again to return it to the original position
136. er Front facing When you install a child restraint in a rear outboard or center seat follow these steps 1 Position the child restraint on the seat It can be placed in a front facing direction depending on the size of the child Always follow the restraint manufacturer s instruc tions 1 30 Seats restraints and supplemental air bag systems INSERT to x Front facing Loe Pull to engage automatic lockin mode gt mae 2 SS0107 Front facing PULL to tighten SSS0062 2 Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage Be sure to follow the child restraint manu facturer s instructions for belt routing 3 Pull on the shoulder belt until all of the belt is fully extended At this time the belt retractor is in the automatic locking mode child restraint mode It reverts back to emergency locking mode when the belt is fully retracted 4 Allow the belt to retract Pull up on the belt to remove any slack in the belt Seats restraints and supplemental air bag systems 1 31 Front facing Check for a secure fit SSS0108 Before placing the child in the child re straint use force to tilt the child restraint from side to side and tug it forward to make sure that it is securely held in place Check that the retractor is in the automatic locking mode by trying
137. erity side collision Always wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents 1 12 Seats restraints and supplemental air bag systems The seat belts and the supplemental side air bag are most effective when you are sitting well back and upright in the seat The side air bag inflates with great force Do not allow anyone to place their hand leg or face near the side air bag on the side of the seatback of the front seat Do not allow anyone sitting in the front seat to extend their hand out of the win dow or lean against the door Some examples of dangerous riding posi tions are shown in the previous illus SS0162 trations e When sitting in the rear seat do not hold onto the seatback of the front seat If the supplemental side air bag inflates the occupant may be seri ously injured Be especially careful with children who should always be properly restrained e Do not use seat covers on the front seatbacks They may interfere with supplemental side air bag inflation Seats restraints and supplemental air bag systems 1 13 Supplemental front air bag modules Diagnosis sensor unit f Seat belt pre tensioner retractor Supplemental side air bag modules if so equipped x Satellite sensors if so equipped SS0151B Supplemental front air bag system The driver supplemental air bag is located in the center of the steering wheel t
138. ertification label is affixed as shown This label contains valuable vehicle information such as Gross Vehicle Weight Ratings GVWR Gross Axle Weight Rating GAWR month and year of manufacture Vehicle Identification Number VIN etc Re view it carefully EMISSION CONTROL INFORMATION LABEL The emission control information label is at tached as shown Technical and consumer information 10 11 D ST10206 STI0189 TIRE PLACARD AIR CONDITIONER The cold tire pressure is shown on the tire SPECIFICATION LABEL placard affixed to the console box lid The air conditioner specification label is affixed inside of the hood as shown 10 12 Technical and consumer information INSTALLING FRONT LICENSE PLATE Mounting holes Flat as License plate bracket mie ee Screw Le Screw S nut e STI0191 Screw Use the following steps to mount the license plate Before mounting the license plate confirm that the following parts are enclosed in the vinyl bag e License plate bracket e J nut x 2 e Screw x 2 e Screw grommet x 2 1 Temporarily place the license plate bracket while aligning points of the front bumper fascia with holes in the license plate bracket 2 Remove the license plate bracket 3 Carefully drill two pilot holes using a 0 39 in 10 mm drill bit at the marked locations Be sure that the drill only goes through the fascia or damage to th
139. essing the UNLOCK button on multi remote controller The alarm will not stop if the ignition switch is turned to ACC or ON If the system does not operate as de scribed above have it checked by your NISSAN dealer NISSAN VEHICLE IMMOBILIZER SYSTEM The Nissan Vehicle Immobilizer System will not allow the engine to start without the use of the registered Nissan Vehicle Immobilizer Sys tem key If the engine fails to start using the registered Nissan Vehicle Immobilizer System key it may be due to interference caused by another Nissan Vehicle Immobilizer System key an automated toll road device or automated pay ment device on the key ring Restart the en gine using the following procedures 1 Leave the ignition switch in the ON position for approximately 5 seconds 2 Turn the ignition switch to the OFF or LOCK Instruments and controls 2 13 position and wait approximately 5 seconds 3 Repeat step 1 and 2 again 4 Restart the engine while holding the device which may have caused the interference separate from the registered Nissan Ve hicle Immobilizer System key If this procedure allows the engine to start NISSAN recommends placing the regis tered Nissan Vehicle Immobilizer System key on a separate key ring to avoid inter ference from other devices Statement related to section 15 of FCC rules for Nissan Vehicle Immobilizer Sys tem CONT ASSY IMMOBILIZER This device complies with part 15 of the FCC Ru
140. ever has the proper travel and make sure that the vehicle is held securely on a fairly steep hill when only the parking brake is applied Automatic transaxle P Park position mechanism On a fairly steep hill check that the vehicle is held securely with the selector lever in the P Park position without applying any brakes 9 4 Maintenance Under the hood and the vehicle The maintenance items listed here should be checked periodically for example each time you check the engine oil or refuel Windshield washer fluid Check that there is adequate fluid in the tank Engine coolant level Check the coolant level when the engine is cold Radiator and hoses Check the front of the radiator and clean off any dirt insects leaves etc that may have accumulated Make sure the hoses have no cracks deformation dete rioration or loose connections Brake and clutch fluid levels Make sure that the brake and clutch fluid levels are be tween the MAX and MIN lines on the reservoir Battery Check the fluid level in each cell It should be between the MAX and MIN lines Engine drive belts Make sure that no belt is frayed worn cracked or oily Engine oil level Check the level on the dipstick after parking the vehicle on a level spot and turning off the engine Power steering fluid level and lines Check the level in the reservoir tank with the engine off Check the lines for proper attachment leaks cracks et
141. f and check the alternator belt If the belt is loose broken missing or if the light remains on see your NISSAN dealer immedi ately AA CAUTION Do not continue driving if the belt is loose broken or missing 4 This light comes on when any of the doors are not closed securely while the ignition key is ON A Seat belt warning light and chime Door open warning light The light and chime remind you to fasten seat belts The light illuminates whenever the igni tion key is turned to ON and will remain illuminated until the drivers seat belt is fas tened At the same time the chime will sound for about 6 seconds unless the driver s seat belt is securely fastened See Seat belts in the 1 Seats restraints and supplemental air bag systems section for pre cautions on seat belt usage 2 8 Instruments and controls AY Supplemental air bag warning light After turning the ignition key to the ON posi tion the supplemental air bag warning light will illuminate The supplemental air bag warning light will turn off after about 7 seconds if the system is operational If any of the following conditions occur the supplemental front air bag supplemental side air bag and pre tensioner seat belt needs servicing and your vehicle must be taken to your nearest authorized NISSAN dealer e The supplemental air bag warning light remains on after approximately 7 seconds e The
142. f so equipped Be sure to dispose of the cloth used to cover the vent holes as it may be contaminated with corrosive acid PUSH STARTING CAUTION e Automatic transmission models can not be push started This may cause transmission damage Three way catalyst equipped models should not be started by pushing since the three way catalyst may be damaged Never try to start the vehicle by tow ing it when the engine starts the forward surge could cause the ve hicle to collide with the tow vehicle In case of emergency 6 9 IF YOUR VEHICLE OVERHEATS A WARNING e Do not continue to drive if your ve hicle overheats Doing so could cause a vehicle fire e To avoid the danger of being scalded never remove the radiator cap while the engine is still hot When the radia tor cap is removed pressurized hot water will spurt out possibly causing serious injury e Do not open the hood if steam is coming out If your vehicle is overheating indicated by an extremely high temperature gauge reading or if you feel a lack of engine power detect abnormal noise etc take the following steps 1 Move the vehicle safely off the road apply the parking brake and move the shift lever to the N Neutral position automatic trans mission to the P Park position Do not stop the engine Turn off the air conditioner switch Open all the windows move the heater or air condi 6 10 In case of emergency tioner t
143. formed with the wheels off the vehicle Spin balancing the front wheels on the vehicle could lead to transmission damage Care of wheels Wash the wheels when washing the vehicle to maintain their appearance Clean the inner side of the wheels when the wheel is changed or the underside of the vehicle is washed Do not use abrasive cleaners when wash ing the wheels Inspect wheel rims regularly for dents or corrosion Such damage may cause loss of pressure or poor seal at the tire bead NISSAN recommends that the road wheels be waxed to protect against road salt in areas where it is used during winter Spare tire T type spare tire US only Canadian vehicles are equipped with a full size spare tire Observe the following precautions if the T type spare tire must be used otherwise your ve hicle could be damaged or involved in an accident Do it yourself 8 35 CAUTION The T type spare tire should be used only for emergency It should be re placed by the standard tire at the first opportunity Drive carefully while the T type spare tire is installed Avoid sharp turns and abrupt braking while driving Periodically check the T type spare tire inflation pressure and always keep it at 60 psi 420 kPa 4 2 bar Always keep the pressure of the full size spare tire if so equipped at the recommended pressure for standard tires as indicated on the tire placard For tire placard location see Tire pla
144. fter parking in the sun drive for 2 or 3 minutes with the windows open to vent hot air from the passenger compartment Then close the windows This will allow the air conditioner to cool the interior more quickly The air conditioning system should be operated for about 10 minutes at least once a month This helps prevent dam age to the system due to lack of lubrica tion If the coolant temperature gauge exceeds the HOT position turn the air conditioning off For additional information see If your vehicle overheats in the 6 In case of emergency section AIR FLOW CHARTS The charts on the following pages show the button and lever positions for maximum and 4 6 Heater air conditioner and audio systems quick heating cooling or defrosting The air recirculation button should be in the OFF position for normal cooling heat ing and defrosting DEFROSTING DEFOGGING Air passed through heater core Air flow control buttons REAR fom Fan control dial Air recirculation button Temperature control lever AC Air Air flow Temp Fan button recirculation control control control Air conditioning button SAA0375 HEATING Heated air at center vents Air passed through heater core Air flow control buttons Fan control dial Air conditioning button Air recirculation button Temperature control lever AIC Air Air fiow Temp Fan button recirculation control control co
145. fter turning the ignition key to the ON position the supplemental air bag warning light illuminates The supplemental air bag warning light will turn off after about 7 seconds if the system is operational 1 16 Seats restraints and supplemental air bag systems WARNING Do not place any objects near the seatback of the front seats Also do not place any objects an umbrella bag etc between the front door fin isher and the front seat Such objects may become dangerous projectiles and cause injury if the supplemental side air bag inflates Right after inflation several supple mental side air bag system compo nents will be hot Do not touch them you may severely burn yourself No unauthorized changes should be made to any components or wiring of the supplemental side air bag sys tem This is to prevent accidental inflation of the side air bag or damage to the side air bag system Do not make unauthorized changes to your vehicle s electrical system suspension system or side panel This could affect proper operation of the supplemental side air bag sys When selling your vehicle we request that you tem inform the buyer about the supplemental side air bag system and guide the buyer to the appropriate sections in this Owner s Manual Pre tensioner seat belt system For e Work around and on the pre front seats tensioner system should be done by operation Tampering with the pre tensioner seat belt system m
146. g parking on Hills ee eee eee eee tees Power Stoer i ssccsesvioesescossusercesetsoaisoensavdcecbecnsizes Brake system Braking precautions Anti lock brake system ABS ou eee eee Traction control system if so equipped Cold weather driving Freeing a frozen door lock ANWAR OZG EE E T Battery eeir ar AN sie Draining of coolant water Tire CQUIPIMEME siiin Special winter equipment sseesseesreeerererrrrnenees Driving ON SNOW OF iC sesei Engine block heater if so equipped PRECAUTIONS WHEN STARTING AND DRIVING AA WARNING e Do not leave children impaired adults or pets alone in your vehicle They could accidentally injure them selves or others through inadvertent operation of the vehicle Also on hot sunny days temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously injured Keep the car locked with the trunk closed when not in use and prevent children s access to car keys EXHAUST GAS Carbon monoxide WARNING Do not breathe exhaust gases they con 5 2 Starting and driving tain colorless and odorless carbon mon oxide Carbon monoxide is dangerous It can cause unconsciousness or death e If you suspect that exhaust
147. he vehicle is impacted These supplemental restraint systems are de signed to supplement the crash protection provided by the driver and front passenger seat belts and are not a substitute for them Seat belts should always be correctly worn and the driver and front passenger seated a suitable distance away from the steering wheel instrument panel and front door finish ers See Seat belts later in this section for instructions and precautions on seat belt us age After turning the ignition key to the ON position the supplemental air bag warning light illuminates The supplemental air bag warning light will turn off after about 7 seconds if the system is operational Sit upright and well back SSS0131 AA WARNING e The supplemental front air bags ordi narily will not inflate in the event of a side impact rear impact roll over or lower severity frontal collision Al ways wear your seat belts to help reduce the risk or severity of injury in various kinds of accidents The seat belts and the supplemental front air bags are most effective when you are sitting well back and upright in the seat Front air bags inflate with great force If you are unrestrained leaning forward sitting sideways or out of position in any way you are at greater risk of injury or death in a crash and may also receive serious or fatal injuries from the supplemen tal front air bag if you are up against it when
148. he front passenger supplemental air bag is mounted in the dashboard above the glove box These systems are designed to meet optional certifi cation requirements under U S regulations They are also permitted in Canada The op tional certification allows front air bags to be designed to inflate somewhat less forcefully than previously However all of the informa tion cautions and warnings in this manual still apply and must be followed The front air bags are designed to inflate in higher severity frontal collisions although they may inflate if the forces in another type of collision are similar to those of a higher severity frontal impact They may not inflate in certain frontal collisions Vehicle damage or lack of it is not always an indication of proper supplemental air bag operation When the supplemental front air bag inflates a fairly loud noise may be heard followed by release of smoke This smoke is not harmful and does not indicate a fire but care should be taken not to inhale it as it may cause irritation and choking Those with a history of a breath ing condition should get fresh air promptly 1 14 Seats restraints and supplemental air bag systems Supplemental front air bags along with the use of seat belts helps to cushion the impact force on the face and chest of the front occupants They can help save lives and reduce serious injuries However an inflating front air bag may cause facial abrasions or other
149. he throttle body to attempt to start your vehicle AA CAUTION If fuel is spilled on the car body flush it away with water to avoid paint dam age Tighten until the fuel filler cap clicks Failure to tighten the fuel filler cap properly may cause the ane mal function indicator lamp MIL to illu Pre driving checks and adjustments 3 1 1 minate If the ANF lamp illuminates because the fuel filler cap is loose or missing tighten or install the cap and continue to drive the vehicle The ane lamp should turn off after a few driving trips If the S amp F lamp does SOON not turn off after a few driving trips have the vehicle inspected by an au thorized NISSAN dealer e For additional information see the Malfunction indicator lamp MIL in the 2 Instruments and controls section 3 12 Pre driving checks and adjustments STEERING WHEEL ADJUST SPA0234 SUN VISORS Extension sun visor SPA0991 TILT OPERATION Pull the lock lever and while holding down adjust the steering wheel up or down to the desired position Push the lock lever back into place to lock the steering wheel in place WARNING Do not adjust the steering wheel while driving You could lose control of your vehicle and cause an accident AA CAUTION Store the main sun visor after storing the extension sun visor MIRRORS SPA0470 ee Down SPA0987 INSIDE MIRROR Th
150. he turn than your vehicle wheels To compensate for this make a larger than normal turning radius during the turn Crosswinds and rough roads will adversely affect vehicle trailer handling possibly causing vehicle sway When being passed by larger vehicles be prepared for possible changes in crosswinds that could affect vehicle handling If swaying does occur firmly grip the steering wheel steer straight ahead and immediately but gradually re duce vehicle speed This combination will help stabilize the vehicle Never increase speed Be careful when passing other vehicles Passing while towing a trailer requires con siderably more distance than normal pass ing Remember the length of the trailer must also pass the other vehicle before you can safely change lanes To maintain engine braking efficiency and electrical charging performance do not use fifth gear manual transmission or over drive automatic transmission e Avoid holding the brake pedal down too long or too frequently This could cause the brakes to overheat resulting in reduced braking efficiency When towing a trailer change oil in the transmission more frequently See Periodic maintenance schedules in the 9 Maintenance section UNIFORM TIRE QUALITY GRADING DOT Department Of Transportation Quality Grades All passenger car tires must conform to federal safety requirements in addition to these grades Quality grades can be foun
151. heel spin on slippery roads The system operates only if it senses one or both of the front wheels spinning or beginning to lose traction When this happens the system reduces engine power and may also upshift the transmission to help limit wheel spin e Indicator light If a malfunction occurs in the traction con trol system the SLIP and indicator lights come on in the meter panel As long as these warning lights are on the traction control function is canceled The vehicle will behaves like a model without the traction control system AA CAUTION e The traction control system is most effective when the transmission gear selector is in the D position e Ifyou drive in gear 1 or 2 with the TCS on this could cause the three way catalyst to overheat and be damaged To avoid this the TCS will automati cally turn off Shifting the gear selec tor to D will reactivate the TCS WARNING This system is designed to prevent the wheels from spinning However it does not prevent vehicle slipping or spinning due to abrupt steering operation at high speeds or by careless or dangerous driving techniques Be especially care ful when driving on slippery surfaces and always drive safely COLD WEATHER DRIVING FREEING A FROZEN DOOR LOCK To prevent a door lock from freezing apply de icer or glycerin to it through the key hole If the lock becomes frozen heat the key before inserting it into the key hole ANTI FREEZE
152. her COUNTY E E E T E T T 10 10 Remote keyless entry See multi remote control C E E E E E Reporting safety defects USA only ROMOVE sz c3s83 eseces cers secesedeivdieaaesdeaeiecveiicinis S Safety Child seat Dols sirrrrssnrn insense 1 22 Reporting safety defects USA only 10 20 TOWING SAISY ccsecsecce casccsecscesdicewaueenease 10 17 Seat adjustment Front manual seat adjustment 0000 1 2 Front power seat adjustment 1 4 Rear seat adjustment ceeeeeeereeeeeeee 1 6 Seat belt extenders ccccesesseseeeeeeees 1 27 Seat belt maintenance eee 1 27 Seat belt warning light m Seat belt warning light and chime 0 00 2 8 Seat belt s Child Safe Mine inina naa 1 22 Infants and small children eee 1 23 Injured persons 1 24 Larger children 1 23 Pre tensioner seat belt system 1 17 Precautions on seat belt usage 1 20 Pregnant WOMEN cccceesesseseeeeeeeees 1 23 Seat DellCleaNiNG aissei 7 5 Seat belig sicccccisseetstece cece csstsieedieee cases deeeee 1 20 Three point type with retractor 1 24 Seat s Seats oo ei eeeeceeeeeneeeeeeeeeeeeeeeeeeeteeeees 1 2 Seats Heated Seats cceeeeeeeeeeeeeeeeeeereeee 2 21 Security system Nissan Vehicle Immobilizer System Engine start eee Security systems See theft warning Servicing air conditioner Shift lock release eeecese
153. hift lever to N Neutral position For an automatic transmission move the selector lever to P Park position e Be sure the ignition key is OFF or LOCK when performing any parts re placement or repairs e Your vehicle is equipped with an au tomatic engine cooling fan It may come on at any time without warning even if the ignition key is in the OFF position and the engine is not run ning To avoid injury always discon 8 2 Do it yourself nect the negative battery cable before working near the fan If you must work with the engine running keep your hands clothing hair and tools away from moving fans belts and any other moving parts It is advisable to secure or remove any loose clothing and any jewelry such as rings watches etc before working on your vehicle Always wear eye protection when ever you work on your vehicle If you must run the engine in an enclosed space such as a garage be sure there is proper ventilation for exhaust gases to escape Never get under the vehicle while it is supported only by a jack If it is nec essary to work under the vehicle support it with safety stands Keep smoking materials flame and sparks away from fuel and the bat tery On gasoline engine models with the Multiport Fuel Injection MFI System the fuel filter or fuel lines should be serviced by a NISSAN dealer because the fuel lines are under high pressure even when the engine is off AA CAUTION
154. ht load limit specified for the front or rear axle DETERMINING VEHICLE LOAD CAPACITY The load capacity of this vehicle is determined by weight not by available cargo space For example a luggage rack bike carrier cartop carrier or similar equipment does not increase load carrying capacity of your vehicle To determine vehicle load capacity Vehicle weight can be determined by using a commercial grade scale found at places such as a truck stop gravel quarry grain elevator or a scrap metal recycling facility 1 Determine the curb weight of your vehicle 2 Compare the curb weight amount to the GVWR specified for your vehicle to deter mine how much more weight your vehicle can carry 3 After loading cargo and passengers re weigh your vehicle to determine if either GVWR or GAWR for your vehicle is ex ceeded If GVWR is exceeded remove cargo as necessary If either the front or rear GAWR is exceeded shift the load or remove cargo as necessary LOADING TIPS e The GVW must not exceed GVWR or GAWR as specified on the F M V S S cer tification label e Do not load the front and rear axle to the GAWR Doing so will exceed the GVWR WARNING e Properly secure all cargo to help pre vent it from sliding or shifting Do not place cargo higher than the seat backs In a sudden stop or collision unsecured cargo could cause per sonal injury e Do not load your vehicle any heavier than the GVWR or th
155. ibit their use Check local state and provincial laws before in stalling studded tires Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non studded snow tires 3 Tire chains may be used if desired Make sure they are of proper size for the tires on your vehicle and are installed according to the chain manufacturer s suggestions Use of tire chains may be prohibited according to location Check the local laws before installing tire chains When installing tire chains make sure they are of proper size for the tires on your vehicle and are in stalled according to the chain manufactur ers suggestions Use only SAE Class S chains Other types may damage your vehicle Use chain tensioners when recom mended by the tire chain manufacturer to ensure a tight fit Loose end links of the tire chain must be secured or removed to pre vent the possibility of whipping action dam age to the fenders or underbody If pos sible avoid fully loading your vehicle when using tire chains In addition drive at a reduced speed Otherwise your vehicle may be damaged and or vehicle handling and performance may be adversely af fected Never install tire chains on a T type spare tire Do not use tire chains on dry roads SPECIAL WINTER EQUIPMENT It is recommended that the following items be carried in the vehicle during winter e ascraper and stiff bristled brush to remove ice and snow
156. ically Air flow distribution and fan speed are also controlled automatically e Do not set the temperature lower than the outside air temperature Otherwise the sys tem may not work properly e Not recommended if windows fog up 4 10 Heater air conditioner and audio systems Dehumidified defogging 1 Push the DEF button y on The indica tor light on the button will come on 2 Turn the temperature set dial to the left or right to set the desired temperature e To quickly remove ice or fog from the outside of the windows push the manual fan control button lt 2 and set to the maxi mum position gg e As soon as possible after the windshield is clean push the AUTO button to return to the auto mode e When the DEF button lt 7 is pushed the air conditioner will automatically be turned on at outside temperatures above 23 F 5 C to defog the windshield and the air recirculate mode will automatically be turned off Outside air is drawn into the passenger compartment to improve the defogging per formance MANUAL OPERATION Fan speed control Push the fan control button lt 2 control the fan speed i to manually Push the AUTO button to return to automatic control of the fan speed Air recirculation Push the air recirculation button gt to recir culate interior air inside the vehicle The indi cator light on the switch will come on Push it again to make the air inlet controlled automatically
157. icle may be reset to a not ready condition Before taking the I M test drive the vehicle through the following pattern to set the vehicle to the ready condition If you cannot or do not want to perform the driving pattern an NISSAN dealer can conduct it for you WARNING Always drive the vehicle in a safe and prudent manner according to traffic con ditions and obey all traffic laws 1 Start the engine when the engine coolant temperature gauge needle points to C Al low the engine to idle until the gauge needle points between the C and H normal oper ating temperature 2 Accelerate the vehicle to 55 MPH 88 km h then quickly release the accelerator pedal completely and keep it released for at least 6 seconds 3 Quickly depress the accelerator pedal for a moment then drive the vehicle at a speed of 53 to 60 MPH 86 to 96 km h for at least 5 minutes 4 Stop the vehicle 5 Accelerate the vehicle to 35 MPH 55 km h and maintain the speed for 20 seconds 6 Repeat steps 4 and 5 at least 3 times 7 Accelerate the vehicle to 55 MPH 88 km h and maintain the speed for at least 3 min utes 8 Stop the vehicle shift lever in the P or N position 9 Rev the engine up between 2 500 and 3 500 rpm and hold it for 3 consecutive minutes then release the accelerator pedal completely 10 Wait 5 second at idle 11 Rev the engine up between 2 000 and 3 000 rom and maintain it for 5 consecutive
158. icle operation Use these buttons for manual tuning To move quickly through the channels hold either of the TUNE buttons down for more than 0 5 sec onds DW ZA SEEK SCAN tuning SEEK tuning Push the SEEK SCAN tuning button or ZA for less than 1 5 seconds SEEK tuning begins from high to low or low to high frequen cies and stops at the next broadcasting sta tion SCAN tuning Push the SEEK SCAN tuning button or for more than 1 5 seconds SCAN tuning begins from high to low or low to high frequen cies and stops at each broadcasting station for 10 seconds Pushing the button again during this 10 seconds period will stop SCAN tuning and the radio will remain tuned to that station If the SEEK SCAN tuning button is not pushed within 10 seconds SCAN tuning moves to the next station Keep pushing the memory channel Indicator will come on SAA0382 Station memory operations Twelve stations can be set for the FM band six for FM1 six for FM2 Six stations can be set for the AM band 1 Tune to the desired station using the SEEK SCAN or TUNE button 2 Push the desired station select button for more than 1 5 seconds For example in the diagram ch2 is to be memorized The radio mutes when the select button is pushed 3 The indicator ch2 will then come on and the sound will resume Memorizing is now com plete 4 Other buttons can be set i
159. inal equipment tires If you do not it can adversely affect the safety and handling of your vehicle Generally snow tires will have lower speed ratings than factory equipped tires and may not match the potential maximum vehicle speed Never exceed the maximum speed rating of the tire If you operate your vehicle in snowy or icy conditions NISSAN recommends the use of snow or all season tires on all four wheels For additional traction on icy roads studded tires may be used However some provinces and states prohibit their use Check local state and provincial laws before installing studded tires Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non studded snow tires TIRE CHAINS Use of tire chains may be prohibited according to location Check the local laws before install ing tire chains When installing tire chains make sure they are of proper size for the tires on your vehicle and are installed according to the chain manufacturers suggestions Use only SAE class S chains Other types may damage your vehicle Use chain tensioners when recommended by the tire chain manu facturer to ensure a tight fit Loose end links of the tire chain must be secured or removed to prevent the possibility of whipping action dam age to the fenders or undercarriage If pos sible avoid fully loading your vehicle when using tire chains In addition drive at a re duced speed Otherwis
160. indicate the presence of a hazard that could cause minor or moder ate personal injury or damage to your vehicle To avoid or reduce the risk the procedures must be followed carefully SIC0697 If you see this symbol it means Do not do this or Do not let this happen CALIFORNIA PROPOSITION 65 WARNING WARNING Engine Exhaust some of its constitu ents and certain vehicle components contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm 2000 NISSAN MOTOR CO LTD TOKYO JAPAN All rights reserved No part of this Owner s Manual may be reproduced or stored in a retrieval system or trans mitted in any form or by any means electronic me chanical photocopying recording or otherwise without the prior written permission of Nissan Motor Co Ltd Welcome To The World Of NISSAN NISSAN RESEARCH amp DEVELOPMENT INC in Farmington Hills Michigan NISSAN MOTOR MANUFACTURING CORPORATION U S A in Smyrna Tennessee AFWO0001 Your new NISSAN is the result of our dedication to produce the finest in safe reliable and eco nomical transportation Your vehicle is the prod uct of a successful worldwide company that manufactures cars and trucks in over 17 coun tries and distributes them in 170 nations NISSAN vehicles are designed and manufac tured by Nissan Motor Co Ltd which was founded in Tokyo Japan in 1933 and NISS
161. indicator light begins to flash rapidly re lease both buttons The Integrated HomeLink Universal Trans ceiver button has now been reprogrammed The new device can be activated by pushing the HomeLink button that was just pro grammed This procedure will not affect any other programmed HomeLink buttons IF YOUR VEHICLE IS STOLEN If your vehicle is stolen you should change the codes of any non rolling code device that has been programmed into HomeLink Consult the Owner s Manual of each device or call the manufacturer or dealer of those devices for additional information When your vehicle is recovered you will need to reprogram the Integrated HomeLink Universal Transceiver with your new transmitter information FCC Notice This device complies with FCC rules part 15 Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference that may be received including interference that may cause undesired operation The transmitter has been tested and com plies with FCC and DOC MDC rules Changes or modifications not expressly approved by the party responsible for com pliance could void the user s authority to operate the device DOC ISTC 1763K1313 FCC I D CB2V67690 3 Pre driving checks and adjustments KOYE esteseieeniers decteatiesivneredd anise ein 3 2 DOOrS iii RAH RA RAR ahahaha Locking with key Locking
162. ine containing oxygenates such as ethanol MTBE and methanol with or without advertising their pres ence NISSAN does not recommend the use of fuels of which the oxygenate content and the fuel compatibility for your NISSAN cannot be readily determined If in doubt ask your ser vice station manager If you use oxygenate blend gasoline please take the following precautions as the usage of such fuels may cause vehicle performance problems and or fuel system damage e The fuel should be unleaded and have an octane rating no lower than that rec ommended for unleaded gasoline e If an oxygenate blend excepting a methanol blend is used it should con tain no more than 10 oxygenate MTBE may however be added up to 15 e If a methanol blend is used it should contain no more than 5 methanol me thyl alcohol wood alcohol It should also contain a suitable amount of appro priate cosolvents and corrosion inhibi tors If not properly formulated with ap propriate cosolvents and corrosion inhibitors such methanol blends may cause fuel system damage and or ve hicle performance problems At this time sufficient data is not available to ensure that all methanol blends are suit able for use in NISSAN vehicles If any undesirable driveability problems such as engine stalling and hard hot starting are experienced after using oxygenate blend fu els immediately change to a non oxygenate fuel or a fuel with a low blend of MT
163. ine oil if necessary 11 Dispose of waste oil in the proper manner WARNING e Prolonged and repeated contact with used engine oil may cause skin can cer e Try to avoid direct skin contact with used oil If skin contact is made wash thoroughly with soap or hand cleaner as soon as possible e Keep used engine oil out of reach of children CHANGING ENGINE OIL FILTER 1 Park the vehicle on a level surface and apply the parking brake 2 Turn the engine off 3 Loosen the oil filter with an oil filter wrench Depending on the engine model a special cap type wrench may be required See your NISSAN dealer if in doubt Remove the oil filter by turning it by hand Do it yourself 8 9 AA CAUTION Be careful not to burn yourself as the engine oil may be hot Wipe the engine oil filter mounting surface with a clean rag Be sure to remove any old rubber gasket remaining on the mounting surface of the engine Coat the rubber gasket on the new filter with clean engine oil Screw in the oil filter until a slight resistance is felt then tighten additionally more than 2 3 turn Oil filter tightening torque 10 85 to 15 19 ft lb 14 7 to 20 6 N m Start the engine and check for leakage around the oil filter Correct as required Turn the engine off and wait several min utes Check the oil level Add engine oil if necessary 8 10 Do it yourself AUTOMATIC TRANSMISSION FLUID
164. ing adjustment is neces sary contact your NISSAN dealer AA CAUTION e Do not touch the bulb e Use the same number and wattage as originally installed Wattage 60 55 Bulb no HB2 e Donot leave the bulb out of the head light reflector for a long period of time as dust moisture and smoke may enter the headlight body and affect the performance of the headlight EXTERIOR AND INTERIOR LIGHTS Front turn signal Clearance light Front side marker light Front fog light if so equipped Rear combination light Turn signal Stop Tail Back up Rear side marker light License plate light High mounted stop light if so equipped Interior light Front personal light Step light Trunk light Vanity mirror light if so equipped Wattage W 27 8 3 8 See an authorized NISSAN dealer for assistance Bulb No Do it yourself 8 27 REMOVE 5 INSTALL MDI0006 Replacement procedures All other lights are either type A B C or D When replacing a bulb first remove the lens and or cover 8 28 Do it yourself Front turn signal clearance fight SDI0968 Front side marker light Rear side marker light Do it yourself 8 29 Personal light Without sunroof 8 30 Do it yourself Rear combination light Trunk side High mounted stop light if so equipped Vanity mirror light if so equipped SDI0756 Do it yourself 8 31 TIRES
165. injuries Front air bags and supplemental side air bags do not provide restraint to the lower body The seat belts should be correctly worn and the driver and passenger seated upright as far as practical away from the steering wheel or dash board Since the supplemental front air bags inflates quickly in order to help protect the front occupants the force of the front air bag inflating can increase the risk of injury if the occupant is too close to or is against the air bag module during inflation The air bag will deflate quickly after the collision is over After turning the ignition key to the ON position the supplemental air bag warning light illuminates The supplemental air bag warning light will turn off after about 7 seconds if the system is operational WARNING Do not place any objects on the steer ing wheel pad or on the instrument panel Also do not place any objects between any occupant and the steer ing wheel or instrument panel Such objects may become dangerous pro jectiles and cause injury if the supple mental front air bag inflates Right after inflation several air bag system components will be hot Do not touch them you may severely burn yourself No unauthorized changes should be made to any components or wiring of the supplemental front air bag sys tem This is to prevent accidental inflation of the air bag or damage to the air bag system Do not make unauthorized changes to your vehicle s
166. ioning system in your NISSAN vehicle is charged with a refrigerant designed with the environment in mind This refrigerant will not harm the earth s ozone layer How ever special charging equipment and lubricant are required when servicing your NISSAN air conditioner Using improper refrigerants or lu bricants will cause severe damage to your air conditioning system See Capacities and rec ommended fuel lubricants in the 10 Techni cal and consumer information section for air conditioning system refrigerant and lubricant recommendations Your NISSAN dealer will be able to service your environmentally friendly air conditioning system AA WARNING The air conditioner system contains re frigerant under high pressure To avoid personal injury any air conditioner ser vice should be done only by an experi enced technician with proper equip ment Heater air conditioner and audio systems 4 11 AUDIO SYSTEM Turn the ignition key to ACC or ON and press the power on switch to turn on the radio If you listen to the radio with the engine not running the key should be turned to the ACC position Radio reception is affected by station signal strength distance from radio transmitter build ings bridges mountains and other external influences Intermittent changes in reception quality normally are caused by these external influences Using a cellular phone in or near the ve hicle may influence radio reception qu
167. ior light or the personal light switch is in the ON position the interior personal vanity mirror and trunk lights will automatically turn off 10 minutes after the ignition switch has been turned to the OFF position To turn on the light again insert the key into the ignition switch and move it to the ON position TRUNK LIGHT The light illuminates when the trunk lid is opened When the trunk lid is closed the light will go off When the interior light or the personal light switch is in the ON position the interior personal vanity mirror and trunk lights will automatically turn off 10 minutes after the ignition switch has been turned to the OFF position To turn on the light again insert the key into the ignition switch and move it to the ON position INTEGRATED HomeLink UNIVERSAL TRANSCEIVER if so equipped The Integrated HomeLink Universal Trans ceiver provides a convenient way to consoli date the functions of up to three individual hand held transmitters into one built in device Integrated HomeLink Universal Transceiver e Will operate most Radio Frequency RF devices such as garage doors gates home and office lighting entry door locks and security systems e ls powered by your vehicle s battery No separate batteries are required If the vehi cle s battery is discharged or is discon nected HomeLink will retain all program ming Once the Integrated HomeLink Universal Transceiver is prog
168. ir recircu late mode will automatically be turned off Outside air is drawn into the passenger compartment to improve the defogging per formance Bi level heating This mode directs outside air from the side and center vents and hot air from the floor outlets 1 Push the air recirculation button to the OFF position 2 Push the button in 3 Turn on the fan control dial 4 Normally move the temperature control le ver to the midpoint between HOT and COLD Heating and defogging This mode heats the interior and defogs the windshield 1 Push the yy button in 2 Turn on the fan control dial 3 Move the temperature control lever to the desired position between the middle and the HOT position Operating tips e Clear snow and ice from the wiper blades and air inlet in front of the wind shield This will improve heater opera tion e When the 3y button is pushed the air recirculate mode will turned off automatically be Outside air is drawn into the passenger compartment to improve the defogging per formance AIR CONDITIONER OPERATION Start the engine move the fan control dial to the desired 1 to 4 position and push in the air conditioning button to activate the air condi tioner When the air conditioner is on cooling and dehumidifying functions will be added to the heater operation Cooling This mode is used to cool and dehumidify 1 Push the air recirculation button to the OFF
169. ire belt assembly According to accident statistics chil should be replaced A WARNING dren are safer when properly re strained in the rear seat than in the e Infants and small children should al front seat ways be placed in an appropriate child restraint while riding in the ve hicle Failure to use a child restraint can result in serious injury or death e An improperly installed child re straint could lead to serious injury or death in an accident e Infants and small children should never be carried on your lap It is not possible for even the strongest adult to resist the forces of a severe acci dent The child could be crushed be Child restraints for infants and children of tween the adult and parts of the ve various sizes are offered by several manufac hicle Also do not put the same seat turers When selecting any child restraint belt around both your child and your keep the following points ia mind In general child restraints are designed to be installed with the lap portion of a three point type seat belt self e choose only a restraint with a label certify z z ing that it complies with Federal Motor e Never install a rear facing child re Vehicle Safety Standard 213 or Canadian straint in the front seat An inflating Motor Vehicle Safety Standard 213 supplemental air bag could seriously f a f injure or kill your child A rear facing e check the child restraint in your vehicle to be sure it is compatib
170. ires may have a lower speed rating than the factory equipped tires and may not match the potential maximum vehicle speed Never exceed the maximum speed rating of the tire Periodically check the tire pressure including spare Incorrect tire pressure may adversely affect tire life and vehicle handling Tire pres sure should be checked when tires are COLD e Do not drive your vehicle over 85 Tires are considered COLD after the vehicle MPH 140 km h unless it is equipped has been parked for 3 or more hours or driven 8 32 Do it yourself that the tire pressure is at the speci tied level All season tires NISSAN specifies all season tires on some models to provide good performance for use all year around including snowy and icy road conditions All season tires are identified by ALL SEASON and or M amp S on the tire sidewall Snow tires have better snow traction than all season tires and may be more appropriate in some areas Summer tires NISSAN specifies summer tires on some mod els to provide superior performance on dry roads Summer tire performance in snow and ice will be substantially reduced Summer tires do not have the tire traction rating M amp S on the tire sidewall If you operate your vehicle in snowy or icy conditions NISSAN recommends the use of snow or all season tires on all four wheels Snow tires If snow tires are needed it is necessary to select tires equivalent in size and load rating to the orig
171. it inflates Always sit back against the seatback and as far away as practical from the steering Seats restraints and supplemental air bag systems 1 9 wheel or instrument panel Always use the seat belts e Keep hands on the outside of the steering wheel Placing them inside the steering wheel rim could increase the risk that they are injured when the supplemental front air bag inflates Sit upright and well back 1 10 Seats restraints and supplemental air bag systems Seats restraints and supplemental air bag systems 1 11 WARNING e Never let children ride unrestrained or extend their hands or face out of the window Do not attempt to hold them in your lap or arms Some ex amples of dangerous riding positions are shown in the previous illustra tions Children may be severely injured or killed when the supplemental front air bag or supplemental side air bag in flates if they are not properly re strained Also never install a rear facing child restraint in the front seat An inflating supplemental front air bag could se riously injure or kill your child For additional information see Child re straints later in this section Do not lean against the door SSS0101 WARNING Supplemental side air bag if so quipped e The supplemental side air bag ordi narily will not inflate in the event of a frontal impact rear impact or lower sev
172. itable for your vehicle s engine Using fuel with too low an octane rating may cause engine damage All gasoline vehicles must be operated with unleaded engine gaso line Therefore avoid taking your vehicle to areas where appropriate fuel is not available When transferring the registration of your vehicle to another country state province or district it may be necessary to modify the vehicle to meet local laws and regulations The laws and regulations for motor vehicle emission control and safety standards vary according to the country state province or district therefore vehicle specifications may differ When any vehicle is to be taken into an other country state province or district and registered its modifications transpor tation and registration are the responsibil ity of the user NISSAN is not responsible for any inconvenience that may result 10 10 Technical and consumer information VEHICLE IDENTIFICATION ST10038 VEHICLE IDENTIFICATION NUMBER VIN PLATE The vehicle identification number plate is at tached as shown This number is the identifi cation for your vehicle and is used in the vehicle registration VEHICLE IDENTIFICATION NUMBER Chassis number The number is stamped as shown ST10186 ENGINE SERIAL NUMBER The number is stamped on the engine as shown F M V S S CERTIFICATION LABEL The Federal Motor Vehicle Safety Standards F M V S S c
173. lation of electrical equipment should also be done by an authorized NISSAN dealer Unauthorized electri cal test equipment and probing de vices should not be used on the pre tensioner seat belt system e If you need to dispose of the pre tensioner or scrap the vehicle con tact an authorized NISSAN dealer Correct pre tensioner disposal proce dures are set forth in the appropriate NISSAN Service Manual Incorrect disposal procedures could cause personal injury The front seat pre tensioner seat belt system activates in conjunction with the supplemental front air bag Working with the seat belt retrac tor it helps tighten the seat belt the instant the vehicle becomes involved in certain types of Seats restraints and supplemental air bag systems 1 17 collisions thereby restraining seat occupants The pre tensioner is encased with the seat belt s retractor These seat belts are used the same as conventional seat belts When the pre tensioner seat belt activates smoke is released and a loud noise may be heard The smoke is not harmful but care should be taken not to inhale it as it may cause irritation and choking If any abnormality occurs in the pre tensioner system the supplemental air bag warning light At will not come on will flash intermittently or will turn on for 7 seconds and remain on after the ignition key has been turned to the ON or START position In this case the pre tensioner seat belt may not func
174. le only after a thorough washing Follow the instructions supplied with the wax e Do not use a wax containing any abrasives cutting compounds or cleaners that may damage the vehicle finish e f the surface does not polish easily use a road tar remover and wax again Machine compounding or aggressive pol ishing on a base coat clear coat paint finish may dull the finish or leave swirl marks REMOVING SPOTS Remove tar and oil spots industrial dust in sects and tree sap as quickly as possible from the surface of the paint to avoid lasting dam age or staining Special cleaning products are available at your NISSAN dealer or any auto motive accessory store UNDERBODY In areas where road salt is used in winter the underbody must be cleaned regularly This will prevent dirt and salt from building up and causing underbody and suspension corrosion Before the winter period and again in the spring the underseal must be checked and if necessary re treated High mounted stop light removal ZN _SAI0014A GLASS When cleaning the rear window it may be easier to clean if the high mounted stop light is removed first Be careful when removing the high mounted stop light to reduce the risk of damaging the high mounted stop light wires The high mounted stop light must be properly reinstalled before driving your vehicle Use glass cleaner to remove smoke and dust film from the glass surfaces It is normal for
175. le the key is removed from the ignition switch e The key is removed from the ignition switch while all doors are closed The ceiling light will turn off while the 30 second timer is activated when e The driver s door is locked either with the multi remote controller a key the door lock knob or the lock unlock switch e The ignition switch is turned ON When the interior light switch or personal light switch is in the ON position the inte rior personal vanity mirror and trunk lights will automatically turn off 10 minutes after the ignition switch has been turned to the OFF position To turn on the light again insert the key into the ignition switch and move it to the ON position After the above procedure the interior per sonal vanity mirror or trunk lights will auto matically turn off 10 minutes after the latest operation of the following with the ignition switch in the ACC or OFF position e Opening or closing any door or trunk lid e Locking or unlocking the driver s door e Inserting or removing a key from the ignition switch These lights will turn on again when any of the above operations is performed after the lights have turned off automatically The lights will turn off 10 minutes after the latest operation of the above as well AA CAUTION e Turn off the interior personal and vanity mirror lights when you leave the vehicle e Do not use for extended periods of time with the engine stopped
176. le which is compatible with the installed seat belts The extender adds approximately 8 inches 200 mm of length and may be used for either the driver or front passenger seating position See your NISSAN dealer for assistance if the ex tender is required WARNING e Only NISSAN belt extenders made by the same company which made the original equipment belts should be used with NISSAN belts e Persons who can use the standard seat belt should not use an extender Such unnecessary use could result in serious personal injury in the event of an accident SEAT BELT MAINTENANCE e To clean the seat belt webbings apply a mild soap solution or any solution recom mended for cleaning upholstery or carpets Then brush the webbing wipe it with a cloth and allow it to dry in the shade Do not allow the seat belts to retract until they are com pletely dry e If dirt builds up in the shoulder belt guide of the seat belt anchors the seat belts may retract slowly Wipe the shoulder belt guide with a clean dry cloth e Periodically check to see that the seat belt and the metal components such as Seats restraints and supplemental air bag systems 1 27 CHILD RESTRAINTS buckles tongues retractors flexible wires PRECAUTIONS ON CHILD and anchors work properly If loose parts RESTRAINTS e NISSAN recommends that the child deterioration cuts or other damage on the restraint be installed in the rear seat webbing is found the ent
177. le with the vehicle s seat and seat belt system Choose a child restraint that meets the guidelines of the Society of Automotive Engineers recom child restraint must only be used in the rear seat 1 28 Seats restraints and supplemental air bag systems mended practice J1819 for child restraint installation e if the child restraint is compatible with your vehicle place your child in the child re straint and check the various adjustments to be sure the child restraint is compatible with your child Always follow all recom mended procedures All US states and Canadian provinces re quire that infants and small children be restrained in approved child restraints at all times while the vehicle is being oper ated WARNING e Improper use of a child restraint can result in increased injuries for both the infant or child and other occu pants in the vehicle e Follow all of the child restraint manu facturer s instructions for installation and use When purchasing a child restraint be sure to select one which will fit your child and vehicle It may not be possible to properly install some types of child restraints in your vehicle If the child restraint is not anchored properly the risk of a child being injured in a collision or a sudden stop greatly increases Adjustable seatbacks should be posi tioned to fit the child restraint but as upright as possible After attaching the child restraint test it bef
178. les Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must ac cept any interference received including interference that may cause undesired op eration 2 14 Instruments and controls Indicator light SECURITY SIC1228 Security indicator light If Nissan Vehicle Immobilizer System is mal functioning this light will remain on while the ignition key is in the ON position If the light still remains on and or the en gine will not start see your NISSAN dealer for Nissan Vehicle Immobilizer System ser vice as soon as possible Please bring all Nissan Vehicle Immobilizer System keys that you have when visiting your NISSAN dealer for service WINDSHIELD WIPER AND WASHER SWITCH Type A r ca f y Intermittent PULL to wash 4 Low speed y High speed Type B Turn intermittent time control knob Intermittent g Low speed J High speed PULL to wash SIC0176 The windshield wiper and washer operates when the ignition key is in the ON position Push the lever down to operate the wiper Intermittent operation can be adjusted from 2 to 13 seconds by turning the knob Type B only Pull the lever toward you to operate the washer Then the wiper will also operate sev eral times WARNING In freezing temperatures the washer so lution may freeze on the windshield and obscure your vision whi
179. lock all doors simultaneously e Turning the driver s door key to the front of the vehicle will lock all doors e Turning the drivers door key one time to the rear of the vehicle will unlock the corre sponding door From that position return ing the key to neutral where the key can only be removed and inserted and turning it to the rear again within 5 seconds will unlock all doors LOCKING WITH INSIDE LOCK KNOB To individually lock the doors from the outside move the inside lock knob to the LOCK posi tion then close the door To unlock pull up the inside lock knob to the unlock position When locking the door without a key be sure not to leave the key inside the vehicle LOCKING WITH POWER DOOR LOCK SWITCH All door locks will be engaged when the power door lock switch is moved to the LOCK posi tion with the driver s or front passenger s door open Then close the door and all doors will be locked When the power door lock switch is moved to the LOCK position with front doors open while a key is in the ignition switch all doors will lock once and then unlock automatically Pre driving checks and adjustments 3 3 CHILD SAFETY REAR DOOR LOCK Child safety locking helps prevent doors from being opened accidentally especially when small children are in the vehicle When the lever is in the lock position the rear door can be opened only from the outside 3 4 Pre driving checks and adjustments
180. ls 2 29 CLOCK INTERIOR LIGHT WARNING H button e In an accident you could be thrown from the vehicle through an open Si sunroof Always use seat belts and Ime child restraints um Ser e Do not allow anyone to stand up or extend any portion of their body out of the opening while the vehicle is in M button motion or while the sunroof is clos ing SIC0910 IC1226 The digital clock displays time when the igni CEILING A CAUTION tion key is in ACC or ON iih eal faineHicdk The ceiling light has a three position switch i e power supply is disconnected the cloc ae B e Remove water drops snow ice or will not indicate the correct time Readjust the When the switch is in the center O position the sand from the sunroof before open time light will illuminate when a door is opened ing 3 ADJUSTING THE TIME The light will stay on for about 30 seconds e Do not place any heavy object on the when sunroof or surrounding area Push the H button to adjust the hour i e The doors are unlocked by the multi remote Push the M button to adjust the minute controller while all doors are closed and If the sunroof does not close locked with the key in the ignition switch Have your NISSAN dealer check and repair e The driver s door is unlocked while the key the sunroof is removed from the ignition switch and all doors are closed and locked 2 30 Instruments and controls e Thedriver s door is opened and then closed whi
181. malfunction in the system Have the system checked by your NISSAN dealer Once the pre tensioner seat belt has activated it cannot be reused and Seats restraints and supplemental air bag systems 1 21 Sit upright and well back NC z 880136 must be replaced together with the retractor See your NISSAN dealer Removal and installation of the pre tensioner seat belt system compo nents should be done by an autho rized NISSAN dealer All seat belt assemblies including re tractors and attaching hardware should be inspected after any colli sion by your NISSAN dealer NISSAN recommends that all seat belt assem blies in use during a collision be replaced unless the collision was mi nor and the belts show no damage and continue to operate properly Seat belt assemblies not in use dur ing a collision should also be in spected and replaced if either dam age or improper operation is noted 1 22 Seats restraints and supplemental air bag systems CHILD SAFETY Children need adults to help protect them They need to be properly restrained The proper restraint depends on the child s size Generally infants up to about 1 year and less than 20 Ib 9 kg should be placed in rear facing child restraints Front facing child re straints are available for children who outgrow rear facing child restraints WARNING Infants and children need special pro tection The vehicle s se
182. ments and controls HORN e Do not use the hazard warning flash ers while moving on the highway un less unusual circumstances force you to drive so slowly that your ve hicle might become a hazard to other traffic nissan PUSH e Turn signals do not work when the hazard warning flasher lights are on The flasher can be actuated with the ignition switch either off or on SIC1280 To sound the horn push the center pad area of the steering wheel HEATED SEATS if so equipped For front passenger side seat For driver a e The front seats are warmed by built in heaters The switches located on the center console can be operated independently of each other 1 Start the engine 2 Select heat range e For low heat press the top of the switch e For high heat press the bottom of the switch e Forno heat the switch has a center OFF position between low and high The indicator light in the switch will illumi nate when low or high is selected The heater is controlled by a thermostat automatically turning the heater on and off The indicator light will remain on as long as the switch is on When the vehicle s interior is warmed or before you leave the vehicle be sure to turn the switch off AA CAUTION The battery could run down if the seat heater is operated while the engine is not running Do not use the seat heater for ex tended periods or when no one is using the seat
183. moisture retaining dirt and debris in body panel sections cavities and other areas e Damage to paint and other protective coat ings caused by gravel and stone chips or minor traffic accidents ENVIRONMENTAL FACTORS INFLUENCE THE RATE OF CORROSION Moisture Accumulation of sand dirt and water on the vehicle body underside can accelerate corro sion Wet floor coverings will not dry com pletely inside the vehicle and should be re moved for drying to avoid floor panel corrosion Relative humidity Corrosion will be accelerated in areas of high relative humidity especially those areas where the temperatures stay above freezing and where atmospheric pollution exists and road salt is used Appearance and care 7 5 Temperature A temperature increase will accelerate the rate of corrosion to those parts which are not well ventilated Air pollution Industrial pollution the presence of salt in the air in coastal areas or heavy road salt use will accelerate the corrosion process Road salt will also accelerate the disintegration of paint surfaces TO PROTECT YOUR VEHICLE FROM CORROSION e Wash and wax your vehicle often to keep the vehicle clean e Always check for minor damage to the paint and repair it as soon as possible e Keep drain holes at the bottom of the doors open to avoid water accumulation e Check the underbody for accumulation of sand dirt or salt If present wash with water as soon as po
184. n the same manner If the battery cable is disconnected or if the fuse blows the radio memory will be can celled In that case reset the desired stations Cassette tape player operation Turn the ignition key to ACC or ON and then lightly insert the cassette tape into the tape door The cassette tape will be automatically pulled into the player The radio or CD will turn off if it is on and the cassette tape will begin to play Heater air conditioner and audio systems 4 21 CAUTION Do not force the cassette tape into the tape door This could cause player dam age If the system is turned off by pushing the ON OFF VOL control knob with the cassette tape still in the player the tape will resume playing when the system is turned back on Precautions on cassette tape player operation e To maintain good quality sound NISSAN recommends that you use cas sette tapes of 60 minutes or shorter in length e Cassette tapes should be removed from the player when not in use Store cas settes in their protective cases and away from direct sunlight heat dust mois ture or magnetic sources Direct sunlight can cause the cassette to become deformed The use of deformed cassettes may cause the cassette to jam in the player e Do not use cassettes that have peeling 4 22 Heater air conditioner and audio systems or loose labels If used the label could jam in the player e If a cassette has loose tape inser
185. na seat belt is allowed to wind back into the P retractor the automatic locking mode child restraint mode is canceled the seat belt only locks during a sudden stop or impact PULL to tighten Check for a secure fit SSS0114 4 Allow the belt to retract Pull up on the belt 5 Before placing the child in the child re to remove any slack in the belt straint use force to tilt the child restraint from side to side and tug it forward to make sure that it is securely held in place 6 Check that the retractor is in the automatic locking mode by trying to pull more belt out of the retractor If you cannot pull any more belt webbing out of the retractor the belt is in the automatic locking mode 7 Check to make sure that the child restraint is properly secured prior to each use If the lap belt is not locked repeat steps 3 through 6 After the child restraint is removed and the 1 38 Seats restraints and supplemental air bag systems MEMO Seats restraints and supplemental air bag systems 1 39 2 Instruments and controls Instrument pana lssiisiriieis iar erriei 2 2 Meters and QaUuges ceeeseeseseeeseeeeeeeseneseeeaeees 2 3 Speedometer and odometer cceeceeeeteeeeeeeees 2 4 Tachometer A 2 4 Engine coolant temperature gauge sseeseeseee 2 5 Fuel QAUQG risarnir N 2 5 Warning indicator lights and chimes 6 2 7 Checking DulbSisiseccssiss ccceveevi
186. nchor cover from the anchor point which is located directly behind the child seat Secure the top tether strap to the anchor bracket Keep the removed cover in a secured place to prevent loss or damage to the cover AA WARNING The child restraint anchor point is de signed to withstand only those loads imposed by correctly fitted child re straints Under no circumstance is it to be used for adult seat belts or har nesses Anchor point locations Anchor points are located on the rear parcel shelf finisher When installing a top strap child restraint on the rear seat for the first time consult your NISSAN dealer for details Seats restraints and supplemental air bag systems 1 35 INSTALLATION ON FRONT PASSENGER SEAT WARNING e Never install a rear facing child re straint in the front passenger seat Supplemental air bags inflate with great force A rear facing child re straint could be struck by the supple mental air bag in a crash and could seriously injure or kill your child e NISSAN recommends that child re straints be installed in the rear seat However if you must install a front facing child restraint in the front pas senger seat move the passenger seat to the rearmost position A child restraint with a top tether strap should not be used in the front passenger seat The three point belt in your vehicle is equipped with a locking mode retrac tor which must be used when install
187. nd re ceiver FM signals follow a line of sight path exhibiting many of the same characteristics as light For example they will reflect off objects Fade and drift As your vehicle moves away from a station transmitter the signals will tend to fade and or drift Static and flutter During signal interference from buildings large hills or due to antenna position usually in conjunction with increased distance from the station transmitter static or flutter can be heard This can be reduced by adjusting the treble control counterclockwise to reduce treble response Multipath reception Because of the reflective characteristics of FM signals direct and re flected signals reach the receiver at the same time The signals may cancel each other resulting in momentary flutter or loss of sound AM RADIO RECEPTION AM signals because of their low frequency can bend around objects and skip along the ground In addition the signals can be bounced off the ionosphere and bent back to earth Because of these characteristics AM signals are also subject to interference as they travel from transmitter to receiver Fading Occurs while the vehicle is passing through freeway underpasses or in areas with many tall buildings It can also occur for sev eral seconds during ionospheric turbulence even in areas where no obstacles exist Static Caused by thunderstorms electrical power lines electric signs and even traffic lights Hea
188. nes amp cables I l l Brake pads amp rotors l l l Manual transaxle oil amp automatic transaxle fluid l l l l Steering gear amp linkage axle amp suspension parts l l Tire rotation See NOTE 2 Exhaust system l l Front drive shaft boots l l Supplemental air bag system and supple mental side air bag systems See NOTE 1 Automatic Speed Control Device ASCD vacuum hoses l NOTE 1 Inspect the supplemental air bag systems 10 years after the date of manufacture noted on the F M V S S certification label 2 Refer to Tire rotation under the General maintenance heading earlier in this section Maintenance 9 9 EXPLANATION OF MAINTENANCE ITEMS Additional information on the following items with is found in the 8 Do it yourself section Emission control system maintenance Drive belts Check drive belts for wear fray ing or cracking and also for proper tension Replace the drive belts if found damaged Air cleaner filter Under normal driving con ditions the air cleaner filter should be replaced in accordance with the maintenance schedule However driving the vehicle in dusty areas may cause more rapid clogging of the element Consequently the element may have to be replaced more frequently EVAP vapor lines Check EVAP vapor lines and connections for failure or looseness If leaks are found replace them Fuel lines Check the fuel hoses
189. ngarnncdoeneess 10 14 Lock Door locks 3 2 Glove box lock 2 25 Power door lock asniusiann 3 2 Trunk lid lock opener lever cee 3 9 Low fuel warning light 0 cee 2 9 Luggage NEE esis cess ceceestecevneccevsaczerseccensencernecaens 2 26 M Maintenance Batley x cinan ccna Seared 8 13 Explanation of maintenance items 9 3 9 10 General maintenance ceee 9 2 9 3 Inside the vehicle ccccccceeseeeeeeeee 9 2 9 3 Maintenance precautions Outside the vehicle eeeeeeeeeeee Periodic maintenance schedules 9 5 Seat belt maintenance eeeeeeeeee 1 27 Under the hood and vehicle ee 9 4 Manual front seat adjustment 1 2 Meters and gauges 2 3 Mirror ISIN MIO urana 3 13 Outside MIRON enspi 3 13 11 4 Outside mirror contrOl 0 eee 3 13 Outside MINOT S wisces cceusecssye tetas ecceyecersteedes 3 13 Multi remote control system 0 cee 3 4 N Net Luggage ets ccccccscte testis eects eace cates 2 26 New vehicle break in ceseeceeereeereereeeee 5 15 Nissan vehicle Immobilizer System 2 12 E gine start uepisaiti 5 6 o OOOMCLC 22s eri E E 2 4 Oil Capacities and recommended fuel IWC ANS aiii cree cede e rninn 10 2 Changing engine oil Changing engine oil filter 8 9 Checking engine oil level 8 7 Engine Oil airiran ean en ei 8 7 Engine oil viscosity
190. ns Inspect Correct or replace if necessary MAINTENANCE OPERATION MAINTENANCE INTERVAL Miles x 1 000 38 7 5 113 15 188 225 263 30 33 8 37 5 413 45 488 525 563 60 pene aa aaber of miles kilometersor kmx1 000 12 18 24 80 36 42 48 54 60 66 72 78 84 90 96 Months 3 6 9 12 15 18 21 24 27 30 33 36 39 42 45 48 Chassis and body maintenance Brake lines amp cables l l Brake pads amp rotors l l l l Manual transaxle oil or automatic transaxle fluid See NOTE 1 l i Steering gear amp linkage axle amp suspension parts l l l l Tire rotation See NOTE 3 Exhaust system l l l I l l Front drive shaft boots l l l l l Supplemental air bag system and supplemental side air bag systems See NOTE 2 Automatic Speed Control Device ASCD vacuum hoses I l l NOTE 1 If towing a trailer using a camper or a car top carrier or driving on rough or muddy roads change not just inspect oil at every 30 000 miles 48 000 km or 24 months 2 Inspect the supplemental air bag systems 10 years after the date of manufacture noted on the F M V S S certification label 3 Refer to Tire rotation under the General maintenance heading earlier in this section Maintenance 9 7 Schedule 2 Abbreviations R Replace Inspect Correct or replace if necessary At the mileage intervals only MAINTENANCE OPERATION MAINTENANCE INTERVAL Miles
191. nt Be alert and drive defensively at all times Obey all traffic regulations Avoid excessive speed high speed cornering or sudden steer ing maneuvers because these driving prac tices could cause you to lose control of your vehicle As with any vehicle a loss of con trol could result in a collision with other vehicles or objects or cause the vehicle to rollover particularly if the loss of control causes the vehicle to slide sideways Be attentive at all times and avoid driving when tired Never drive when under the influence of alcohol or drugs including prescription or over the counter drugs which may cause drowsiness Always wear your seat belt See Seat Belts in the 1 Seats restraints and supplemental air bag systems section And also instruct your passengers to do so Starting and driving 5 3 IGNITION SWITCH DRINKING ALCOHOL DRUGS AND your ability to operate your vehicle is impaired DRIVING by alcohol drugs or some other physical condition OFF Automatic transmission model WARNING Never drive under the influence of alco hol or drugs Alcohol in the bloodstream reduces coordination delays reaction time and impairs judgment Driving after drinking alcohol increases the likeli hood of being involved in an accident injuring yourself and others Addition ally if you are injured in the accident alcohol can increase the severity of the injury NISSAN is committed to safe driving But yo
192. ntrol OFF amp _ RIGHT Face RIGHT Heater air conditioner and audio systems 4 7 SAA0376 HEATING No air at center vents Air passed through heater core Air flow control buttons Fan control dial Air recirculation button 4 8 Heater air conditioner and audio systems Air conditioning button Temperature control lever AC Air Air flow Temp Fan button recirculation control control control HOT por a n pa SAA0377 COOLING Air not passed through heater core Air flow control buttons REAR fom a Fan control dial Air recirculation button Air conditioning button Temperature control lever AC Air Air flow ES kA button recirculation control ES kA COLD SAA0378 HEATER AND AIR CONDITIONER Automatic if so equipped On hot sunny days temperatures in a closed vehicle could quickly be come high enough to cause severe or Rear window and outside mirror if so equipped defogger switch Refer to the section 2 Instruments and controls Front DEF button Display AMB button possibly fatal injuries to people or _ animals X A 3 AUTO e Do not use the recirculation mode for MANUAL long periods as it may cause the interior air to become stale and the windows to fog up IGF NASL e Positioning of the heating or air con ditioning controls should not be done while driving so full attention may be given to vehi
193. ntrols 2 25 Lid PUSH x to lower PULL UP the lever e a to open the tray PUSH to elevate PULL UP S to open the lid 2K RE g PULL UP the lever to open the tray SIC1236 CONSOLE BOX WARNING used while driving so full attention may be given to vehicle operation The center console box should not be 2 26 Instruments and controls ee ae net retainers The retainers on the other side are in the same location SIC1242A CARGO NET if so equipped The cargo net helps keep packages in the cargo area from moving around while your vehicle is driven To install the cargo net attach the hooks to the retainers To remove the cargo net detach the hooks from the cargo net retainers WARNING e Properly secure all cargo to help pre vent it from sliding or shifting Be sure to secure hooks into the retainers The cargo restrained in the net must not exceed 30 Ib 13 6 kg or the net may not stay secured WINDOWS Main switch __ Power door lock switch PUSH DOWN PULL UP to open to close Ke N Driver side Rear left passenger side S Lock button Front passenger side Pag Rear right lt id passenger sige SIC0929 POWER WINDOWS WARNING e Make sure that all passengers have their hands etc inside the vehicle before closing the windows Use the window lock switch to prevent unex pecte
194. o reset at a slower cruising speed use one of the following three methods a Lightly tap the brake pedal When the ve hicle attains the desired speed push the COAST SET switch and release it b Push and hold the COAST SET switch Release the switch when the vehicle slows down to the desired speed c Push then quickly release the COAST SET switch Each time you do this the set speed will decrease by about 1 MPH 1 6 km h To resume the preset speed push and re lease the RES ACCEL set switch The vehicle will resume the last set cruising speed when the vehicle speed is over 25 MPH 40 km h Starting and driving 5 15 BREAK IN SCHEDULE During the first 1 000 miles 1 600 km follow these recommendations for the future reliabil ity and economy of your new vehicle Failure to follow these recommendations may result in vehicle damage or shortened engine life e Do not drive over the legal speed limit and do not run the engine over 4 000 rpm Avoid driving for long periods at constant speed either fast or slow e Donot accelerate at full throttle in any gear e Avoid quick starts e Avoid hard braking as much as possible e Do not tow a trailer for the first 500 miles 800 km 5 16 Starting and driving INCREASING FUEL ECONOMY Abrupt starts and stops waste fuel and money SD1001M Accelerate slowly and smoothly Maintain cruising speeds with a constant accelerator position Drive at mode
195. o the charging pipe as far as it will go Remove the dipstick and note the reading If the level is at the low side of either range add fluid to the charging pipe CAUTION e Do not overfill e Use only NISSAN Matic D Continen tal US and Alaska or Canada Nissan automatic transmission fluid Dexron III Mercon or equivalent may also be used Outside the conti nental US and Alaska contact a NISSAN dealer for more information regarding suitable fluids including recommended brand s of Dexron lll Mercon automatic transmission fluid NOTE If the vehicle has been driven for a long time at high speeds or in city traffic in hot weather or if it is being used to pull a trailer the accurate fluid level cannot be read You should wait until the fluid has cooled down about 30 minutes POWER STEERING FLUID Check the fluid level in the reservoir tank The fluid level should be checked using the HOT range at fluid temperatures of 122 to 176 F 50 to 80 C or using the COLD range at fluid temperatures of 32 to 86 F 0 to 30 C CAUTION e Do not overfill e Use Genuine Nissan PSFIl or equiva lent Do it yourself 8 11 BRAKE AND CLUTCH FLUID Nd CLUTCH p lt MAX hy FSG US a SA AE Check the fluid level in the reservoir If the fluid is below the MIN line or the brake warning light comes on add DOT 3 fluid up to the MAX line If fluid must be added frequently the system
196. oce dure please contact an authorized NISSAN dealer HOW TO USE MULTI REMOTE CONTROL SYSTEM Setting hazard and horn chirp mode This vehicle is set in hazard and horn chirp mode when you first receive the vehicle In hazard and horn chirp mode when the LOCK button is pushed the hazard indicator flashes twice and the horn chirps once When the UNLOCK button is pushed the hazard indicator flashes once If hazard and horn chirp mode is not neces sary you can switch to normal mode by fol lowing the switching procedure In normal mode when the LOCK button is pushed the hazard indicator flashes twice When the UNLOCK button is pushed neither the hazard indicator nor the horn operates Switching procedure Push the LOCK and UNLOCK buttons on the multi remote controller simultaneously for more than 2 seconds to switch from one mode to the other When pushing the buttons to set normal mode the hazard indicator flashes 3 times When pushing the buttons to set hazard and horn chirp mode the hazard indicator flashes once and the horn chirps once OPERATION GUIDE MODE HAZARD AND HORN CHIRP HAZARD once HORN once Push LOCK and UNLOCK buttons Switching indicator LOCK UNLOCK for more than 2 seconds to switch Hazard and f F horn chirp NORMAL HAZARD 3 times HAZARD twice No operation HAZARD twice HAZARD once HORN once SPA0982 Locking doors 1 Rem
197. ock during this check or if you have any questions about belt opera tion see your NISSAN dealer 1 26 Seats restraints and supplemental air bag systems Center of rear seat Selecting correct set of seat belts The center seat belt buckle is identified by the CENTER mark The center seat belt tongue can be fastened only into the center seat belt buckle PUSH button to lower Shoulder belt height adjustment For front seats The shoulder belt anchor height should be adjusted to the position best suited for you See Precautions on seat belt usage earlier in this section To lower push the release button and then move the shoulder belt an chor to the desired position so that the belt passes over the shoulder Release the adjust ment button to lock the shoulder belt anchor into position To raise move the adjuster up to the desired position without pushing the button AA WARNING e After adjustment release the adjust ment button and try to move the shoulder belt down to make sure it is securely fixed in position e The shoulder belt anchor height should be adjusted to the position best for you Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an accident SEAT BELT EXTENDERS If because of body size or driving position it is not possible to properly fit the lap shoulder belt and fasten it an extender is availab
198. omes on when the headlight high beam is on and goes out when the low beam is selected CRUISE Cruise main switch indicator light The light comes on when the cruise control main switch is pushed The light goes out when the main switch is pushed again When the cruise main switch indicator light comes on the cruise control system is operational SET Cruise set indicator light The light comes on while the vehicle speed is controlled by the cruise control system If the light blinks while the engine is running it may 2 10 Instruments and controls indicate there is something wrong with the cruise control system Have the system checked by your NISSAN dealer ENaiNe Malfunction indicator lamp MIL If the malfunction indicator lamp comes on steady or blinks while the engine is running it may indicate a potential emission control prob lem The malfunction indicator lamp may also come on steady if the fuel filler cap is loose or missing or if the vehicle runs out of fuel Check to make sure the fuel filler cap is installed and closed tightly and that the ve hicle has at least three gallons of fuel in the fuel tank After a few driving trips the gine lamp should turn off if no other potential emission control system problem exists Operation The malfunction indicator lamp will come on in one of two ways e Malfunction indicator lamp on steady An emission
199. ore you place the child in it Tilt it from side to side Try to tug it forward and check to see if the belt holds the restraint in place If the restraint is not secure tighten the belt as necessary or put the restraint in another seat and test it again For a front facing child restraint check to make sure the shoulder belt does not go in front of the child s face or neck If it does put the shoulder belt behind the child restraint If you must install a front facing child re straint in the front seat see instruc tions later in this section e When your child restraint is not in use store it in the trunk or keep it secured with a seat belt to prevent it from being thrown around in case of a sudden stop or accident AA CAUTION Remember that a child restraint left in a closed vehicle can become very hot Check the seating surface and buckles before placing your child in the child restraint Seats restraints and supplemental air bag systems 1 29 INSTALLATION ON REAR SEAT OUTBOARD OR CENTER POSITIONS WARNING e The three point belt on your vehicle is equipped with a locking mode retrac tor which must be used when install ing a child restraint e Failure to do so will result in the child restraint not being properly secured It could tip over or otherwise be un secured and cause injury to the child in a sudden stop or collision Front facing Outboard Front SSS0153 Front facing Cent
200. osition Refill the fuel tank before the gauge regis ters Empty Instruments and controls 2 5 The low fuel warning light comes on when the fuel tank is getting low Refuel as soon as it is convenient preferably before the gauge reaches E There will be a small reserve of fuel in the tank when the fuel gauge needle reaches E AA CAUTION e If the vehicle runs out of fuel the Nene malfunction indicator lamp MIL may come on Refuel as soon as possible After a few driving trips the ENGINE lamp should turn off If the lamp remains on after a few driving trips have the vehicle inspected by an au thorized NISSAN dealer e For additional information see the Malfunction indicator lamp MIL later in this section 2 6 Instruments and controls WARNING INDICATOR LIGHTS AND CHIMES Engine oil pressure warning light Charge warning light Door open warning light Seat belt warning light Supplemental air bag warning light Low washer fluid warning light if so equipped CHECKING BULBS Apply the parking brake and turn the ignition key to ON without starting the engine The following lights will come on j OF BRAKE 9 Tcs OFF The following lights come on briefly and then go off amp AaBs Of oF If any light fails to come on it may indicate a burned out bulb or an open circuit in the elec trical system Have the system repaired promptly SE
201. ositions if the key is removed from the switch The starter is designed not to operate if the selector lever is in one of the driving posi tions Manual transmission Move the shift lever to N Neutral position and depress the clutch pedal to the floor while cranking the engine The starter is designed not to operate un less the clutch pedal is fully depressed Crank the engine with your foot off the accelerator pedal by turning the ignition key to START Release the key when the engine starts If the engine starts but fails to run repeat the above procedure e If the engine is very hard to start in extremely cold or hot weather de press the accelerator pedal and hold it to help start the engine e In the summer when restarting the engine within 30 minutes after it has been stopped keep the accelerator pedal fully depressed while starting AA CAUTION Do not operate the starter for more than 10 seconds at a time If the engine does not start turn the key off and wait 10 seconds before cranking again other wise the starter could be damaged 4 Warm up Allow the engine to idle for at least 30 seconds after starting Drive at moderate speed for a short distance first especially in cold weather Starting and driving 5 7 DRIVING THE VEHICLE AUTOMATIC TRANSMISSION The automatic transmission in your vehicle is electronically controlled by a transmission con trol module to produce maximum power an
202. ot come on or go off have the TCS checked by your NISSAN dealer If the light stays on or comes on when you are driving there may be a problem with your traction control system and it may not operate properly Have the system checked by your NISSAN dealer The traction control system indicator light may come on for the following reasons a If the system is turned off by pressing the button on the instrument panel the indicator light will come on and stay on To turn the system back on press the button again The indicator light will go off b If engine speed is above 4 000 rpm ina selected gear Use D range on low fric tion road surfaces If the traction control system indicator light comes on and stays on for an extended period of time when the system is turned on have your vehicle checked by your NISSAN dealer SLIP Slip indicator light if so equipped This light will blink on when your traction control system is limiting wheel spin Slippery road conditions may exist if the slip indicator light blinks on If this happens adjust your driving accordingly You may feel or hear the system working but this is normal The light will blink on for a few seconds after the traction control system stops limiting wheel spin The slip indicator light also comes on when you turn the ignition key to ON The light will go off as you start the engine If the light does not come on or go off have
203. ou are driving contact your NISSAN dealer for repair fd Low fuel warning light This light comes on when the fuel in the tank is getting low Refuel as soon as it is convenient preferably before the fuel gauge reaches E There will be a small reserve of fuel remain ing in the tank when the fuel gauge needle reaches E INDICATOR LIGHTS O D orf Overdrive off indicator light This light comes on during driving when the overdrive switch is pressed to prevent over drive operation The O D OFF indicator light comes on for 2 seconds each time the ignition key is turned ON This shows the light is functioning prop erly If the O D OFF indicator light blinks for approximately 8 seconds after coming on for 2 seconds have your NISSAN dealer check the transmission and repair it if necessary The automatic transmission is equipped with an electronic fail safe mode This system al lows the vehicle to be driven even in the event of damage to the electrical circuits If this Instruments and controls 2 9 occurs the gears automatically engage and lock into third gear See the Driving the vehicle in the 5 Starting and driving section for fail safe before visiting your NISSAN dealer 15 gt Turn signal hazard indicator lights The light flashes when the turn signal switch lever or hazard switch is turned on Z D High beam indicator light Blue This light c
204. ous Never change tires if oncoming traffic is close to your vehicle Wait for pro fessional road assistance MCE0001 Blocks Blocking wheels Place suitable blocks at both the front and back of the wheel diagonally opposite the flat tire to prevent the vehicle from rolling when it is jacked up WARNING Be sure to block the wheel as the vehicle may move and could cause personal injury Removing wheel cover fA CAUTION Do not use your hands to pry off wheel caps Doing so could result in personal injury SCE0288 Getting the spare tire and tools Remove jacking tools and spare tire from the storage area located inside the trunk as illus trated In case of emergency 6 3 For 17 aluminum wheel T ack rod SCE0286 Jack up point and placing jack CE1089 6 4 In case of emergency Jacking up vehicle and removing the damaged tire Carefully read the caution label attached to the jack body and the following instruc tions 1 Place the jack directly under the jack up point as illustrated above so that top of the jack contacts the vehicle at the jack up point Align the jack head between the two notches in the front or the rear as shown Also fit the groove of the jack head between the notches as shown CE1092 The jack should be used on level firm ground 2 Loosen each wheel nut one or two turns by turning counterclockwise with
205. ove the ignition key 1 2 Close all the doors 2 3 Push the LOCK button on the multi remote controller 4 All the doors will lock All of the doors will lock when the LOCK button on the multi remote controller is pushed even though a door remains open and or the ignition key is in the ON posi tion 5 The hazard indicator flashes twice and the horn chirps once e When the LOCK button is pushed with all doors locked the hazard indicator flashes twice and the horn chirps once as a re minder that the doors are already locked 1 Doors lock with the remote controller while a key is in the ignition switch However the panic alarm will not activate when the key is in the ignition switch 2 Doors lock with the remote controller while any door is open However hazard and horn chirp mode will not function Pre driving checks and adjustments 3 5 Door lock unlock LOCK a UNLOCK PUSH to lock As UNLOCK LOCK PUSH to open the trunk lid PUSH to unlock TRUNK BE PUSH to operate the panic alarm Remote controller Trunk lid release SPA0981 Unlocking doors 1 Push the UNLOCK button on the multi remote controller once doors are completely closed e The hazard indicator flashes once if all e The interior light turns on and the light timer activates for 30 seconds when the switch is e Only the driver s door unlocks in the center O position 3 6 Pre driving
206. owly or driving slowly through deep snow sand or mud or for maximum engine braking on steep downhill grades Do not exceed 37 MPH 60 km h in the 1 Low gear position Starting and driving 5 9 REMOVE shift lock cover using flat bladed screwdriver O Shift lock cover i PUSH the release button PUSH the selector lever button MOVE Tool SSD0151 Shift lock release If the battery charge is low the select lever may not move from the P position even with the brake pedal depressed and the select lever button pushed 5 10 Starting and driving To move the select lever push the shift lock release button and select lever button The select lever can be moved to N Neutral To push the shift lock release button using a screwdriver or other tool follow the procedure as illustrated If there is any problem moving the lever out of P Park have your NISSAN dealer check the automatic transmission system as soon as possible WARNING If the selector lever cannot be moved from the P position while the engine is running and the brake pedal is de pressed the stop lights may not work Malfunctioning stop lights could cause an accident injuring yourself and others Accelerator downshift In D position For rapid passing or hill climbing fully depress the accelerator pedal to the floor This shifts the transmission down into second gear or first gear depending on the vehicle speed SSD0110
207. pecific recommendations INSERT to N fasten TEN SSS0018 N POSITION low on the hips SSS0020 THREE POINT TYPE SEAT BELT WITH RETRACTOR WARNING e Every person who drives or rides in this vehicle should use a seat belt at all times e Do not ride in a moving vehicle when the seatback is reclined This can be dangerous The shoulder belt will not be against your body In an accident 1 24 Seats restraints and supplemental air bag systems you could be thrown into it and re ceive neck or other serious injuries You could also slide under the lap belt and receive serious internal inju ries For most effective protection when the vehicle is in motion the seat should be upright Always sit well back in the seat and adjust the seat belt properly INSERT to fasten POSITION low on the hips S i SSS0061 Fastening the seat belts 1 Adjust the seat 2 Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until it snaps The retractor is designed to lock during a sudden stop or on impact A slow pulling motion will permit the belt to move and allow you some freedom of movement in the seat 3 Position the lap belt portion low and snug on the hips as shown 4 Pull the shoulder belt portion toward the retractor to take up extra slack The front passenger and rear seat belts have a cinching mechanism fo
208. placing a tire use the same size speed rating and load carrying capacity as originally equipped See Specifications in the 10 Technical and consumer information sec tion for recommended types and sizes of tires and wheels WARNING e The use of tires other than those recommended or the mixed use of tires of different brands construction bias bias belted or radial or tread patterns can adversely affect the ride braking handling ground clearance body to tire clearance tire chain clearance speedometer calibration headlight aim and bumper height Some of these effects may lead to accidents and could result in serious personal injury e If the wheels are changed for any reason always replace with wheels which have the same offset dimen sion Wheels of a different offset could cause early tire wear possibly degraded vehicle handling character istics and or interference with the brake discs Such interference can lead to decreased braking efficiency and or early brake pad wear e Do not install a deformed wheel or tire even if it has been repaired Such wheels or tires could have structural damage and could fail without warn ing e The use of retread tire is not recom mended Wheel balance Unbalanced wheels may affect vehicle han dling and tire life Even with regular use wheels can get out of balance Therefore they should be balanced as required Wheel balance service should be per
209. port to the driver Move the lever up or down to adjust the seat lumbar area 1 4 Seats restraints and supplemental air bag systems FRONT POWER SEAT ADJUSTMENT AA WARNING e Do not adjust the driver s seat while driving so full attention may be given to vehicle operation e Do not leave children unattended in side the vehicle They could unknow ingly activate switches or controls Unattended children could become involved in serious accidents Operating tips e The motor has an auto reset overload pro tection circuit If the motor stops during operation wait 30 seconds then reactivate the switch e Do not operate the power support seat for a long period of time when the engine is off This will discharge the battery Forward and lo es f Reclining II LN LE SSS0148 Forward and backward Moving the switch forward or backward will slide the seat forward or backward to the desired position Reclining Move the recline switch backward until the desired angle is obtained To bring the seat back forward again move the switch forward and move your body forward The seatback will move forward Seat lifter Driver s seat Push the front or rear end of the switch up or down to adjust the angle and height of the seat cushion Seats restraints and supplemental air bag systems 1 5 levers are in lock position for security of the trunk Driver s seat AA
210. pull the dipstick SSD016 Ne Keep pushing and 1 A WARNING e When engine is running keep hands jewelry and clothing away from any moving parts such as cooling fan and drive belt e Automatic transmission fluid is poi sonous and should be stored care fully in marked containers out of the reach of children TEMPERATURE CONDITIONS FOR CHECKING The fluid level should be checked using the HOT range on the dipstick after the follow ing conditions have been met a the engine should be warmed up to operating temperature b the vehicle should be driven at least 5 minutes c the automatic transmission fluid should be warmed to between 122 and 176 50 and 80 C The fluid can be checked at fluid tempera tures of 86 to 122 F 30 to 50 C using the COLD range on the dipstick after the en gine is warmed up and before driving How ever the fluid should be re checked using the HOT range Park the vehicle on a level surface and set the parking brake Start the engine and then move the selector lever through each gear range Move the selector lever to P Park position after you have moved it through all ranges Front side HOT 122 to 176 F 50 to 80 C Reverse side COLD 86 to 122 F 30 to 50 C au SD10496 3 Check the fluid level with the engine idling 4 Remove the dipstick and wipe it clean with lint free paper Reinsert the dipstick int
211. r child restraint installa tion It is referred to as the automatic locking mode When the cinching mechanism is activated the seat belt cannot be withdrawn again until the seat belt tongue is detached from the buckle and fully retracted For additional information see Child restraints later in this section The automatic locking mode should be used only for child restraint installation During normal seat belt use by a passen ger the locking mode should not be acti vated If it is activated it may cause uncom fortable seat belt tension WARNING When fastening the seat belts be certain that seatbacks are completely secured in the latched position If they are not completely secured in the right position passengers may be injured in an acci dent or sudden stop Seats restraints and supplemental air bag systems 1 25 Y f PRESS to unfasten ref SSS0021 Unfastening the seat belts To unfasten the belt press the button on the buckle The seat belt will automatically retract Checking seat belt operation Your seat belt retractors are designed to lock belt movement using two separate methods e when the belt is pulled quickly from the retractor e when the vehicle slows down rapidly You can check their operation as follows e grasp the shoulder belt and pull quickly forward The retractor should lock and re strict further belt movement If the retractor does not l
212. r with coolant up to the filler opening and also add it to the reservoir tank up to the MAX level If the engine cooling system frequently requires coolant have it checked by your NISSAN dealer Do it yourself 8 5 e Improper servicing can result in reduced R E Radiator cap heater performance and engine overheat ing WARNING e To avoid the danger of being scalded never change the coolant when the engine is hot e Never remove the radiator cap when the engine is hot Serious burns could be caused by high pressure fluid escaping from the radiator 1 Open the radiator cap and drain plug 2 Open the drain plug on the engine block 3 Flush the cooling system by running fresh water through the radiator EN C o P mr a E 4 Close the radiator drain plug and the drain I sp10114 plug on the engine block securely 5 See Capacities and recommended CHANGING ENGINE COOLANT fuellubricants in the 10 Technical and e Major cooling system repairs should be consumer information section for cooling performed by your NISSAN dealer The system capacity Fill the radiator slowly with service procedures can be found in the the proper mixture of coolant and water Fill appropriate NISSAN Service Manual the reservoir tank up to the MAX level Then install the radiator cap 8 6 Do it yourself Front side of engine block Exhaust manifold Imir Exhaust manifold SDI0973 ENGINE
213. rakes function correctly Using the brakes Avoid resting your foot on the brake pedal while driving This overheats the brakes in creases wear on the brake linings and pads and reduces gas mileage To help save the brakes and to prevent the brakes from overheating reduce speed and downshift to a lower gear before going down a slope or long grade Overheated brakes may reduce braking performance and could result in loss of vehicle control WARNING e While driving on a slippery surface be careful when braking accelerating or downshifting Abrupt braking or accelerating could cause the wheels to skid and result in an accident e If the engine is not running or is turned off while driving the power assist for the brakes will not work Braking will be harder ANTI LOCK BRAKE SYSTEM ABS The anti lock brake system controls the brakes at each wheel so the wheels will not lock when braking abruptly or when braking on slippery surfaces The system detects the rotation speed at each wheel and varies the brake fluid pressure to prevent each wheel from locking and sliding By preventing wheel lockup the system helps the driver maintain steering con trol and helps to minimize swerving and spin ning on slippery surfaces Using the system Depress the brake pedal and hold it down WARNING Do not pump the brake pedal Doing so may result in increased stopping dis tances Normal operation The anti lock brak
214. rammed retain the original transmitter for future programming procedures i e new vehicle purchases Upon sale of the vehicle the programmed Integrated HomeLink Universal Trans ceiver buttons should be erased for secu rity purposes For additional information refer to Programming HomeLink later in this section AA WARNING Do not use the Integrated HomeLink Universal Transceiver with any ga rage door opener that lacks safety stop and reverse features as required by federal safety standards These standards became effective for opener models manufactured after April 1 1982 A garage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse does not meet current federal safety standards Using a garage door opener without these features in creases the risk of serious injury or death During programming your garage door or gate may open or close Make sure that people and objects are clear of the garage door or gate that you are programming Your vehicle s engine should be turned off while programming the In Instruments and controls 2 33 tegrated HomeLink Universal Trans ceiver 2 34 Instruments and controls SPAO609A PROGRAMMING HomeLink 1 With the ignition key in the OFF position press and hold the two outside buttons and release when the indicator light begins to flash approximately 20 seconds This pro ced
215. rate speeds on the highway Driving at high speed will lower fuel economy Avoid unnecessary stopping and braking Maintain a safe distance behind other ve hicles Use a proper gear range which suits road conditions On level roads shift into high gear as soon as possible Avoid unnecessary engine idling Keep your engine tuned up Follow the recommended periodic mainte nance schedule Keep the tires inflated at the correct pres sure Low pressure will increase tire wear and waste fuel Keep the front wheels in correct alignment Improper alignment will cause not only tire wear but also lower fuel economy Air conditioner operation lowers fuel economy Use the air conditioner only when necessary When cruising at highway speeds it is more economical to use the air conditioner and leave the windows closed to reduce drag PARKING PARKING ON HILLS Downhill with curb i Uphill with curb U i 1 UJ i L L Uphill or downhill no curb ace S gt ON ON Z OO LS SS ae lt Q Z QS X x w L Z z gt X ne 2S X Q e x SS ne SR x QL MSD0002 WARNING e Do not stop or park the vehicle over flammable materials such as dry grass waste paper or rags They may ignite and cause a fire e Never leave the engine running while the vehicle is unattende
216. re than 8 in 20 cm away from the Multiport Fuel Injection harness Do not route the antenna wire next to any harness e Adjust the antenna standing wave ra tio as recommended by the manufac turer Heater air conditioner and audio systems 4 25 e Connect the ground wire from the CB radio chassis to the body e For details consult an authorized NISSAN dealer 4 26 Heater air conditioner and audio systems 5 Starting and driving Precautions when starting and driving 0 0 5 2 Exhaust gas Carbon monoxide eee 5 2 Three way catalyst Avoiding collision and rollover c eee eee 5 3 Drinking alcohol drugs and driving 0 c eee 5 4 IQMITIOM SWITCM ssisissasieseivieesssaeeeaeetessapoastoscnaseedbanscedtaesae 5 4 Automatic transmission 0 0 cece eect teres 5 4 Manual tranSmiSSlOm 2 2 ccis czejesaceseapezetcaiitsaenasesiceess 5 5 KOy DOSINONS irn 5 6 Nissan Vehicle Immobilizer System 0 ee 5 6 Before starting the Engine 0 reece 5 7 Starting the CNGiNe 0 ee eee iriiri 5 7 Driving the VENICE cescccscasesvevevcesierasssctevsevescrsesbeasoes Automatic transmission Manual transmission siiiu Parking Drako cciesscsssitsetsevivavisiavensiicsreneniteates 5 13 Cruise control teens a Precautions on cruise control Cruise control operations cceeeeeeeeeeeeeeeeeeteeee Break in schedules issis Increasing fuel economy Parkin
217. ropriate NISSAN Serice Manual Incorrect disposal procedures could cause personal injury 1 20 Seats restraints and supplemental air bag systems AA WARNING e Every person who drives or rides in this vehicle should use a seat belt at all times Children should be properly restrained and if appropriate in a child restraint The belt should be properly adjusted to a snug fit Failure to do so may reduce the effectiveness of the entire restraint system and increase the chance or severity of injury in an accident Serious injury or death can occur if the seat belt is not worn properly Always route the shoulder belt over your shoulder and across your chest Never run the belt behind your back under your arm or across your neck The belt should be away from your face and neck but not falling off your shoulder Position the lap belt as low and snug as possible around the hips not the waist A lap belt worn too high could increase the risk of internal injuries in an accident Be sure the seat belt tongue is se curely fastened to the proper buckle Do not wear the belt inside out or twisted Doing so may reduce its ef fectiveness Do not allow more than one person to use the same belt Never carry more people in the ve hicle than there are seat belts If the seat belt warning light glows continuously while the ignition is turned ON with all doors closed and all seat belts fastened it may indicate a
218. s 8 4 Engine cooling system 0 cee 8 5 EnGinet Olli tania ces a Ria 8 7 Engine oil and oil filter recommendation 10 5 Engine oil viSCosity inisenisi 10 5 Engine serial number 0 00c ee 10 11 Engine specifications 0 0 cece 10 7 If your engine overheats s s s 6 10 Starting the engine 0 cee 5 7 Exhaust gas Carbon monoxide 000 5 2 F F M V S S certification label 10 11 Filter Air cleaner housing filter 0 8 17 Flashers See hazard warning flasher SWITCH iscuiscavsnsisnvanacassadicsvenazsunvazsknsezsenteceantnsdanienes Flat tire we FlOOM Mat CleaniING wc eectemeaa sends 7 4 Fluid Automatic transmission fluid ATF 8 10 Brake and clutch fluid ee 8 12 Capacities and recommended fuel IUIBNICANES ates rt cus ohh Meee 10 2 Engine Coolants icsccicnccncnaccanncssnnnaseesnezaene 8 5 Engine oil 8 7 Power steering fluid Window washer fluid 8 12 Fog light SWitChic cisscct eats annan 2 19 Front manual seat adjustment 0 1 2 Front power seat adjustment ceeeeeee 1 4 Fuel Capacities and recommended fuel IUBTICANIS 2205s ccsese ccsens secre eii NEES 10 2 INGO AP A T 3 10 SE secs oii aes chat het cect coe 3 10 Filler lid and CAD aces cess cosets cess coed Mesos conc 3 10 Filler lid opener lever 3 10 Fuel economy a Fuelioctane rating ccc eidiien 10 3 Fuel recommendation
219. s window If the control unit detects something caught in the driver s window as it moves up the window will be immediately lowered The auto reverse function can be activated when the driver s window is closed by auto matic operation when the ignition key is in the ON position or for about 45 seconds after the ignition key is turned to the OFF position e Depending on the environment or driv ing conditions the auto reverse function may be activated if an impact or load similar to something being caught in the window occurs WARNING There are some small distances imme diately before the closed position which cannot be detected Make sure that all passengers have their hands etc in side the vehicle before closing the win dow SUNROOF if so equipped BIS pA CLOSE A cue Ss A Automatically close Front So SIC1293 AUTOMATIC SUNROOF The sunroof will only operate when the ignition key is in the ON position The automatic sunroof is operational for about 45 seconds even if the ignition key is turned to the OFF position If the drivers door or the front passenger s door is opened during this period of about 45 seconds power to the sunroof is canceled Sliding the sunroof To open the roof press and hold the switch to the 7 side To close the roof press and hold the switch to the side Automatic operation To fully open or close the roof completely press the
220. s unlocked by the key or the multi remote controller or the ignition key is turned to ACC or ON the system will not activate e If the key is turned slowly toward the front of the vehicle when locking the door the system may not activate If the key is returned beyond the vertical po sition toward the rear of the vehicle to remove the key the system may be deactivated If the indicator light fails to glow for 30 seconds unlock the door once and lock it again e Even when the driver and or passengers are in the vehicle the system will acti vate with all doors hood and trunk lid locked and ignition key off Turn the ignition key to ACC to turn the system off Theft warning system operation The warning system will give the following alarm e The headlights blink and the horn sounds intermittently e The alarm automatically turns off after 2 to 3 minutes However the alarm reactivates if the vehicle is tampered with again The alarm can be shut off by unlocking a door or trunk lid with the key or by pressing the UNLOCK button on the multi remote con troller The alarm is activated by e Opening the door without using the key or multi remote controller e Opening the trunk lid without using the key or multi remote controller or opening the trunk lid by operating the opener release button e Opening the hood How to stop alarm The alarm will stop only by unlocking a door or trunk lid with the key or by pr
221. seat ADJUST PUSH to lower SSS0125 HEAD RESTRAINT ADJUSTMENT To raise the head restraint just pull it up To lower push the lock knob and push the head restraint down WARNING Head restraints should be adjusted properly as they may provide significant protection against injury in an accident Do not remove them Check the adjust Seats restraints and supplemental air bag systems 1 7 Nal se et NTT Head restraint is level with the tops of your ears SSS0164 Adjust the head restraints so the top is level with the top of your ears Armrest SS0150 ARMREST Pull the armrest forward until it is horizontal 1 8 Seats restraints and supplemental air bag systems SUPPLEMENTAL RESTRAINT SYSTEM PRECAUTIONS ON SUPPLEMENTAL RESTRAINT SYSTEM This Supplemental Restraint System SRS section contains important information con cerning the driver and passenger supplemen tal air bags supplemental side air bags and pre tensioner seat belts Supplemental front air bag system This system can help cushion the impact force to the face and chest of the driver and front passenger in certain frontal collisions Supplemental side air bag system if so equipped This system can help cushion the impact force to the head and the chest area of the driver and front passenger in certain side impact collisions The supplemental side air bag is designed to inflate on the side where t
222. selections the system may not stop in the desired or expected location 2 PROG PROG program Push the PROG button The moving digital squares illuminate on either the right or left side of the display window to indicate the side of program play Heater air conditioner and audio systems 4 17 5 OO Dolby NR Noise Reduction Push the Dolby NR pa button for Dolby NR encoded tapes to reduce high frequency tape noise The J indicator light comes on Dolby NR is manufactured under license from Dolby Laboratories Licensing Corporation DOLBY NR and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation Metal or chrome tape usage The cassette player is automatically set to high performance play when playing a metal or chrome cassette tape EJECT A Ejecting the cassette tape Push the EJECT button The cassette tape automatically comes out 4 18 Heater air conditioner and audio systems FM AM RADIO WITH CASSETTE PLAYER AND COMPACT DISC PLAYER TREBLE FADER BASS BALANCE CD EJECT button are a Station select buttons FM1 FM2 AM ON OFF VOLUME SEEK SCAN band select control knob tuning buttons button control button TAPE EJECT button l adi AUDIO TUNE DISC v A let AA RADIO TUNE buttons CD CHG CD play button TAPE play button SAA0380 FM AM RADIO WITH CASSETTE PLAYER AND COMPACT D
223. signed to inflate in higher severity side collisions although it may inflate if the forces in another type of collision are similar to those of a higher severity side impact It is designed to inflate on the side where the vehicle is impacted It may not inflate in certain side collisions Vehicle dam age or lack of it is not always an indication of proper supplemental side air bag operation When the supplemental side air bag inflates a fairly loud noise may be heard followed by release of smoke This smoke is not harmful and does not indicate a fire but care should be taken not to inhale it as it may cause irritation and choking Those with a history of a breath ing condition should get fresh air promptly Supplemental side air bags along with the use of seat belts help to cushion the impact force on the head and the chest of the front occu pants They can help save lives and reduce serious injuries However an inflating side air bag may cause abrasions or other injuries The seat belts should be correctly worn and the driver and passenger seated upright as far as practical away from the supplemental side air bag Since the side air bag inflates quickly in order to help protect the front occupants the force of the side air bag inflating can increase the risk of injury if the occupant is too close to or is against the side air bag module during inflation The side air bag will deflate quickly after the collision is over A
224. ssible 7 6 Appearance and care CAUTION e NEVER remove dirt sand or other debris from the passenger compart ment by washing it out with a hose Remove dirt with a vacuum cleaner or broom e Never allow water or other liquids to come in contact with electronic com ponents inside the vehicle as this may damage them Chemicals used for road surface de icing are extremely corrosive They accelerate corro sion and deterioration of underbody compo nents such as the exhaust system fuel and brake lines brake cables floor pan and fend ers In winter the underbody must be cleaned periodically For additional protection against rust and cor rosion which may be required in some areas consult your local NISSAN dealer 8 Do it yourself Maintenance precautions eee eee eee 8 2 Engine compartment check locations 8 4 Engine cooling SySteMm eee sinisiin 8 5 Checking engine coolant level eeens 8 5 Changing engine coolant ssassn 8 6 EN QING Oll wesssvscivcceaescsesudocssadpeceeacectapoastoacuaseeSbanseefiaesds 8 7 Checking engine oil level seeen 8 7 Changing engine Oilissa a 8 8 Changing engine oil filter eee 8 9 Automatic transmission fluid 0 0 0 0 8 10 Temperature conditions for checking 0 8 10 Power steering fluid ee eee eee seeeseeeeeeeeereeee 8 11 Brake and clutch flU aiiis 8 12 Window washer flUid 0 0 eee eee eee eeeeeeeeeees Battery 0 0
225. stop light shift to N Neutral and release the clutch pedal with the foot brake 5 12 Starting and driving applied Suggested up shift speeds Shown below are suggested vehicle speeds for shifting into a higher gear These sugges tions relate to fuel economy and vehicle per formance Actual up shift speeds will vary ac cording to road conditions the weather and individual driving habits For normal acceleration in low altitude areas less than 4 000 ft 1 219 m ACCEL shift CRUISE shift Gear change point point MPH km h MPH km h 1st to 2nd 13 21 13 21 2nd to 3rd 23 37 16 26 3rd to 4th 33 53 27 43 4th to 5th 39 63 36 58 For quick acceleration when the engine is cold or in high altitude areas over 4 000 ft 1 219 m Gear change MPH km h 1st to 2nd 15 24 2nd to 3rd 25 40 3rd to 4th 40 64 4th to 5th 45 72 Suggested maximum speed in each gear Downshift to a lower gear if the engine is not running smoothly or if you need to accelerate Do not exceed the maximum suggested speed shown below in any gear For level road driving use the highest gear suggested for that speed Always observe posted speed limits and drive according to the road condi tions which will ensure safe operation Do not over rev the engine when shifting to a lower gear as it may cause engine damage or loss of vehicle control Gear MPH km h tst 30 48 2nd 55 88 3rd 80 128 4th 5th PARK
226. t a pencil through one of the cassette hubs and rewind the tape firmly Loose tape may cause jamming and wavering sound quality e Over a period of time the playback head capstan and pinch roller may gather a tape coating residue as the tape passes over the head This residue ac cumulation can cause a weak or waver ing sound and should be removed peri odically with a head cleaning tape If the residue is not removed periodi cally the player may need to be disas sembled for cleaning TAPE PLAY e When the TAPE button is pushed with the system turned off and a tape loaded the system will come on and the tape will play e When the TAPE button is pushed with either the radio or compact disc turned on and the tape loaded the compact disc or the radio will automatically be turned off and the tape will play p gt lt FF Fast Forward REW Rewind Push the pp fast forward button to fast forward the tape To rewind the tape push the q4 rewind button Either the FF or REW symbol illuminates on the right side of the display window To stop the FF or REW func tion press the p fast forward or lt q re wind again or the TAPE button 2 1 gt gt i laa APS Automatic Program Search FF APS REW When the ppi APS FF button is pushed while the tape is being played the next pro gram will start to play from the beginning Push the APS FF button several
227. t by jump starting the battery may have to be replaced Contact your NISSAN dealer DRIVE BELTS Power steering oil pump Alternator Idler pulley Crankshaft pulley Air conditioner compressor v_ Tension checking points spi0141 AA WARNING Be sure the ignition key is in the OFF or LOCK position The engine could rotate unexpectedly 1 Visually inspect each belt for signs of un usual wear cuts fraying oil adhesion or looseness If the belt is in poor condition or loose have it replaced or adjusted by your NISSAN dealer 2 Have the belts checked regularly for condi tion and tension in accordance with the maintenance schedule in this manual SPARK PLUGS WARNING Be sure the engine and ignition switch are off and that the parking brake is engaged securely AA CAUTION Be sure to use the correct socket to remove the spark plugs An incorrect socket can damage the spark plugs Do it yourself 8 15 Front side oe REMOVE i eer SDI0122 Rear side E DB es Sigs Se 7 A N PUSH remove 4 a te id LOOSEN Ea SDI0123 cs REPLACING SPARK PLUGS f Remove the rocker cover ornament using a suitable hexagon socket Front side 2 Disconnect the electrical connectors Loosen the ignition coil fixing bolts And remove the ignition coil to give access to the spark plugs Remove the spark plugs with a spark plug socket The plug socket has a rub
228. tart the com pact disc 8 cm diameter compact discs can also be used without an adapter Heater air conditioner and audio systems 4 23 CD CHG PLAY When the CD CHG button is pushed with the system off and the compact disc loaded the system will turn on and the compact disc will start to play When the CD CHG button is pushed with the compact disc loaded but the tape or the radio playing the tape or radio will automatically be turned off and the compact disc will start to play a aa FF Fast Forward REW Rewind When the pp fast forward or lt q rewind button is pushed while the compact disc is being played the compact disc will play while fast forwarding or rewinding When the button is released the compact disc will return to normal play speed 2 APS Automatic Program prt i Search FF APS REW When the pp APS FF button is pushed while the compact disc is being played the program next to the present one will start to play from its beginning Push several times to skip through programs The compact disc will advance the number of times the button is pushed When the last program on the com pact disc is skipped through the first program 4 24 Heater air conditioner and audio systems will be played When the 44 APS REW button is pushed the program being played returns to its beginning Push several times to skip back through programs The compact disc
229. tch is securely attached to the vehicle to help avoid personal injury or property damage due to sway caused by crosswinds rough road surfaces or passing trucks 1 000 454 110 49 AA CAUTION e Do not use axle mounted hitches e The hitch should not be attached to or affect the operation of the impact absorbing bumper e Do not modify the vehicle exhaust system brake system etc to installa trailer hitch e Toreduce the possibility of additional damage if your vehicle is struck from the rear where practical remove the hitch and or receiver when not in use After the hitch is removed seal the bolt holes to prevent exhaust fumes water or dust from entering the pas senger compartment e Regularly check that all hitch mount ing bolts are securely mounted Tire pressures e When towing a trailer inflate the vehicle tires to the recommended cold tire pressure indicated on the tire placard located on the inside of the center console lid e Trailer tire condition size load rating and proper inflation pressure should be in ac cordance with the trailer and tire manufac turers specifications Safety chain Always use a suitable chain between your vehicle and the trailer The chain should be crossed and should be attached to the hitch not to the vehicle bumper or axle Be sure to leave enough slack in the chain to permit turning corners Trailer lights Trailer lights should comply with fe
230. ter air conditioner and audio systems 4 13 POWER VOLUME control knob TAPE EJECT button TAPE PLAY STOP button FM AM RADIO WITH CASSETTE PLAYER DOLBY NR indicator FM1 FM2 AM band indicator 4 14 Heater air conditioner and audio systems REW button FF PROGRAM button FM stereo indicator button F VOL EJECT z ZIOU ALD AER PLAY 1 4a 2PROG 3 P gt STOP REW Fe CASERA SEEK SCAN rap 7 si a TUNER ON 4 5 mm 6 AUDIO Emam 4 best TY A TUNE APS REW DOLBY NR APS FF Audio z iigh button button button button indicator light FM1 FM2 AM band select button Manual tuning Bass Treble SEEK SCAN tuning buttons Station select buttons Fader Balance contro buttons SAA0263 FM AM RADIO WITH CASSETTE PLAYER Audio main operation Power Volume control Turn the ignition key to ACC or ON then push the Power Volume control knob The mode radio or cassette which was playing immedi ately before the system was turned off re sumes playing When no cassette is loaded the radio comes on Pushing the Power Volume control knob again turns the system off Turn the Power Volume control knob to adjust the volume pogpg ggg ggggg ggggp PPE PEPEN seati OoRoOOmoCooD Select the audio mode SAA0235 Adjusting tone quality and speaker balance To a
231. ter of the road if it moves 4 Turn the ignition key to the LOCK position and remove the key 5 18 Starting and driving POWER STEERING The power assisted steering is designed to use a hydraulic pump driven by the engine to assist steering If the engine stops or drive belt breaks you will still have control of the vehicle However much greater steering effort is needed espe cially in sharp turns or at low speeds AA WARNING If the engine is not running or is turned off while driving the power assist for the steering will not work Steering will be much harder to operate BRAKE SYSTEM BRAKING PRECAUTIONS The brake system has two separate hydraulic circuits If one circuit develops a problem you will still have braking at two wheels Vacuum assisted brake The brake booster aids braking by using en gine vacuum If the engine stops you can stop the vehicle by depressing the brake pedal However greater foot pressure on the brake pedal will be required to stop the vehicle and the stopping distance will be longer Wet brakes When the vehicle is washed or driven through water the brakes may get wet As a result your braking distance will be longer and the vehicle may pull to one side during braking To dry brakes drive the vehicle at a safe speed while lightly pressing the brake pedal to heat up the brakes Do this until the brakes return to normal Avoid driving the vehicle at high speeds until the b
232. the TCS checked by your NISSAN dealer The traction control sys tem operates in all transmission shift lever positions But the system can upshift the trans mission only as high as the indicated shift lever position CHIMES Key reminder chime The chime will sound if the driver side door is opened while the key is left in the ignition switch ignition switch is turned off Remove the key and take it with you when leaving the vehicle Light reminder chime The headlights will turn off when the front door is opened with the light switch on unless the ignition key is in the ON position When you turn the headlight switch ON again after the lights automatically turn off and when you open the driver s door the lights will not turn off automatically and a chime will sound instead See the battery saver system under Headlight switch in this section for details Make sure to turn the light switch off when you leave the vehicle Seat belt warning chime The chime will sound for about 6 seconds Instruments and controls 2 11 unless the drivers seat belt is securely fas tened Brake pad wear warning The disc brake pads have audible wear warn ings When a brake pad requires replacement it will make a high pitched scraping sound when the vehicle is in motion whether or not the brake pedal is depressed Have the brakes checked as soon as possible if the warning sound is heard 2 12 Instruments and controls SECU
233. the vehicle THREE WAY CATALYST The three way catalyst is an emission control device installed in the exhaust system Ex haust gases in the converter are burned at high temperatures to help reduce pollutants AA WARNING e The exhaust gas and the exhaust sys tem are very hot Keep people ani mals or flammable materials away from the exhaust system compo nents e Do not stop or park the vehicle over flammable materials such as dry grass waste paper or rags They may ignite and cause a fire AA CAUTION e Do not use leaded gasoline Deposits from leaded gasoline seriously re duce the three way catalyst s ability to help reduce exhaust pollutants Keep your engine tuned up Malfunc tions in the ignition fuel injection or electrical systems can cause over rich fuel flow into the three way cata lyst causing it to overheat Do not keep driving if the engine misfires or if noticeable loss of performance or other unusual operating conditions are detected Have the vehicle in spected promptly by an authorized NISSAN dealer Avoid driving with an extremely low fuel level Running out of fuel could cause the engine to misfire damag ing the three way catalyst Do not race the engine while warming it up Do not push or tow your vehicle to start the engine AVOIDING COLLISION AND ROLLOVER WARNING Failure to operate this vehicle in a safe and prudent manner may result in loss of control or an accide
234. tion ings When the ignition key is turned to the OFF position the light will turn off automati When the ignition key is in the ON or ACC cally When the light switch is turned to the paz position the headlight low or high beam will turn off Turn the switch to the paz position The front clearance side marker tail license plate and instrument lights will come on Turn the switch to the 2 position Headlights will come on and all the other lights remain on Instruments and controls 2 17 Photo sensor for autolamp IC1230 Be sure not to put anything on top of the photo sensor located on the top left hand side of the instrument panel The photo sensor controls the autolamp if it is cov ered the photo sensor reacts as if it is dark and the headlights will illuminate Battery saver system e When the headlight switch is in the paz or gD position while the ignition switch is in the ON position the lights including the front fog light will automatically turn off 45 seconds after the ignition switch has been turned to the OFF position However the lights will turn off if the drivers or front 2 18 Instruments and controls passenger s door is opened in this condi tion When the headlight switch remains in the spa OF g position after the lights auto matically turn off the lights will turn on when the ignition switch is turned to the ON position from the OFF position AA CAUTION e When you t
235. tion properly When selling your vehicle we request that you inform the buyer about the pre tensioner seat belt system and guide the buyer to the appro priate sections in this Owners Manual WARNING SRS AIR BAG The warning labels are located on the surface of the sunvisors WARNING SRS SIDE AIR BAG The warning labels are located on both the driver side and passenger side center pillars if so equipped SPA0945A SUPPLEMENTAL AIR BAG WARNING LABELS Warning labels about the supplemental air bag system are placed in the vehicle as shown in the illustration 1 18 Seats restraints and supplemental air bag systems Qo SPA1097 SUPPLEMENTAL AIR BAG WARNING LIGHT The supplemental air bag warning light dis playing inthe instrument panel monitors the circuits of the supplemental front air bag and supplemental side air bag systems and pre tensioner seat belt The circuits monitored by the air bag warning light are the diagnosis sensor unit satellite sensors front air bag modules side air bag modules and all related wiring and pre tensioner seat belt After turning the ignition key to the ON posi tion the supplemental air bag warning light illuminates The supplemental air bag warning light will turn off after about 7 seconds if the system is operational If any of the following conditions occur the supplemental front air bag system supple mental side air bag system and pre tensioner
236. to pull more belt out of the retractor If you cannot pull any more belt webbing out of the retractor the belt is in the automatic locking mode Check to make sure that the child restraint is properly secured prior to each use If the belt is not locked repeat steps 3 through 6 retractor the automatic locking mode child Rear facing restraint mode is canceled the seat belt only Outboard locks during a sudden stop or impact Front Rear facing When you install a child restraint in a rear outboard or center seat follow these steps 1 Position the child restraint on the seat The direction of the child restraint depends on the type of the child restraint and the size of the child Always follow the restraint manu facturer s instructions After the child restraint is removed and the seat belt is allowed to wind back into the 1 32 Seats restraints and supplemental air bag systems Rear facing Center l INSERT to fasten SSS0046 A Rear facing an Pull to engage automatic locking mode SSS0045A 2 Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage Be sure to follow the child restraint manu facturer s instructions for belt routing 3 Pull on the shoulder belt until all of the belt is fully extended At this time the belt retractor is in the automatic locking mode child restraint mode
237. tomated pay ment device on the key ring Restart the en gine using the following procedures 1 Leave the ignition switch in the ON position for approximately 5 seconds 2 Turn the ignition switch to the OFF or LOCK position and wait approximately 5 seconds 3 Repeat step 1 and 2 again 4 Restart the engine while holding the device which may have caused the interference separate from the registered Nissan Ve hicle Immobilizer System key If this procedure allows the engine to start NISSAN recommends placing the registered Nissan Vehicle Immobilizer System key on a separate key ring to avoid interference from other devices BEFORE STARTING THE ENGINE Make sure the area around the vehicle is clear Maintenance items listed here should be checked periodically e g each time you check engine oil Check that all windows and lights are clean Visually inspect tires for their appearance and condition Also check tires for proper inflation Lock all doors Position seat and adjust head restraints Adjust inside and outside mirrors Fasten seat belts and ask all passengers to do likewise Check the operation of warning lights when key is turned to the ON 3 position STARTING THE ENGINE 1 Apply the parking brake 2 Automatic transmission Move the selector lever to P Park or N Neutral P preferred The selector lever cannot be moved out of P Park position and into any of the other gear p
238. u must choose not to drive under the influence of alcohol Every year thousands of people are injured or killed in alcohol related accidents Although the local laws vary on what is con sidered to be legally intoxicated the fact is that alcohol affects all people differently and most people underestimate the effects of alcohol Remember drinking and driving don t mix And that s true for drugs too over the counter prescription and illegal drugs Don t drive if 5 4 Starting and driving SSD0083 AUTOMATIC TRANSMISSION On automatic transmission models the igni tion lock is designed so that the key cannot be turned to LOCK and removed until the selector lever is moved to the P Park position When removing the key from the ignition make sure the selector lever is in the P Park position If the selector lever is not returned to P Park position the key cannot be moved toward LOCK When the key cannot be turned toward the LOCK position proceed as follows to remove the key 1 Move the selector lever into the P Park position 2 Turn the ignition key slightly in the ON direction 3 Turn the key toward the LOCK position 4 Remove the key If the key is removed from the ignition switch the selector lever cannot be moved from P Park position The selector lever can be moved if the ignition switch is in the ACC position This allows the vehicle to be moved if the battery is discharged The
239. ubricants in the 10 Technical and consumer information section for engine oil and oil filter recommendation COLD TIRE PRESSURES See tire placard affixed to the center console lid NEW VEHICLE BREAK IN PROCEDURES RECOMMENDATION During the first 1 000 miles 1 600 km of vehicle use follow the recommendations out lined in the Break in schedule Information found in the 5 Starting and driving section of this Owner s Manual Follow these recommen dations for the future reliability and economy of your new vehicle Failure to follow these rec ommendations may result in vehicle damage or shortened engine life Meters and gauges 2 3 Hood release N Seat 1 2 Trunk release 3 9 Seat belt 1 20 Key 3 2 Fuel 3 10 10 2 Sees Windshield washer fluid 8 12 Engine coolant 8 5 Engine oil 8 7 Audio system 4 12 Air conditioner 4 3 Spare tire 6 3 8 35 ST10205
240. ure erases the factory set default codes and does not have to be followed when programming additional hand held trans mitters 2 Hold the end of the hand held transmitter from the device you wish to train approxi mately 2 to 5 inches 50 to 127 mm away from the surface of HomeLink keeping the indicator light in view 3 Using both hands simultaneously push the hand held transmitter button and the de sired HomeLink button Do not release the buttons until step 4 has been completed NOTE Some garage door openers may require the procedures noted under Canadian Programming 4 The HomeLink indicator light will flash first slowly and then rapidly When the indicator light flashes rapidly both buttons may be released The rapid flashing light indicates the Integrated HomeLink Univer sal Transceiver has been successfully pro grammed To program the remaining two buttons follow steps 2 through 4 If after repeated attempts you do not suc cessfully program the Integrated HomeLink Universal Transceiver to learn the signal of the hand held transmitter refer to Rolling Code Programming later in this section PROGRAMMING HomeLink FOR CANADIAN CUSTOMERS Prior to 1992 D O C regulations required hand held transmitters to stop transmitting af ter 2 seconds To program your hand held transmitter to HomeLink continue to press and hold the HomeLink button note steps 2 through 4 under
241. urn on the headlight switch after the lights automatically turn off the lights will not turn off automatically Be sure to turn the light switch to the OFF position when you leave the vehicle for extended periods of time otherwise the battery will go dead e Never leave the light switch on when the engine is not running for ex tended periods of time iD Brighten Darken IC1284MA Instrument brightness control The instrument brightness control operates when the light switch is in the ZD position spa Or Turn the control to adjust the brightness of instrument panel lights except clock and power window switch lights When the control is turned to the right until a click sound is heard the light intensity will be at maximum When the control is turned to the left until a click sound is heard the light will be turned off Headlight beam select To select the high beam push the lever for ward Pull it back to select the low beam Passing signal Pulling the lever toward you will flash the headlight high beam Daytime running light system Canada only The headlights automatically illuminate at a reduced intensity when the engine is started with the parking brake released The daytime running lights operate with the headlight switch in the OFF position or in the pa position Turn the headlight switch to the 22 position for full illumination when driving at night If the parking brake is applie
242. uts securely in the sequence as illustrated 6 6 In case of emergency A WARNING e Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose or come off This could cause an accident e Do not use oil or grease on the wheel studs or nuts This could cause the nuts to become loose As soon as possible tighten the wheel nuts to the specified torque with a torque wrench Wheel nut tightening torque 72 to 87 ft lb 98 to 118 N m Adjust tire pressure to the COLD pressure COLD pressure After vehicle has been parked for three hours or more or driven less than 1 mile 1 6 km COLD tire pressures are shown on the tire placard affixed to the center console lid WARNING Retighten the wheel nuts when the ve hicle has been driven for 600 miles 1 000 km also in cases of a flat tire etc TURN to tighten Stowing the damaged tire and tools Securely store the spare tire and jacking equipment in the vehicle WARNING e Always make sure that the spare tire and jacking equipment are properly secured after use Such items can become dangerous projectiles in an accident or sudden stop e The T type spare tire and small size spare tire are designed for emer gency use See Tires and wheels in the 8 Do it yourself section JUMP STARTING To start your engine with a booster battery the instructions and precautions below must be followed
243. vailable in mainland US through your NISSAN dealer For additional information see Engine oil in the 8 Do it yourself section for changing engine oil For additional information see Vehicle identification in this section for air conditioner specification label Genuine Nissan PSFIl Canada Nissan Automatic Transmission fluid Dexron III Mercon or equivalent ATF may also be used 10 2 Technical and consumer information FUEL RECOMMENDATION Unleaded premium gasoline with an octane rating of at least 91 AKI Anti Knock Index number Research octane number 96 If unleaded premium gasoline is not avail able unleaded regular gasoline with an octane rating of at least 87 AKI Research octane number 91 can be used However for maximum vehicle perfor mance the use of unleaded premium gaso line is recommended AA CAUTION Using a fuel other than that specified could adversely affect the emission con trol devices and systems and could also affect the warranty coverage Under no circumstances should a leaded gasoline be used since this will damage the three way catalyst Reformulated gasoline Some fuel suppliers are now producing refor mulated gasolines These gasolines are spe cially designed to reduce vehicle emissions NISSAN supports efforts towards cleaner air and suggests that you use reformulated gaso line when available Gasoline containing oxygenates Some fuel suppliers sell gasol
244. veling or registering your vehicle in another COUNMY P E T TE 10 10 Trunk access through rear seat we 1 6 Trunk lid lock opener lever cee 3 9 11 6 Trunk light we 2 33 Turn Signal SwitCh c0c0 cscs cs ascststa een 2 19 U Underbody cleanings see ieee 7 3 Uniform tire quality grading 10 19 V Vanity miror ligt sssusa ald 2 32 Vehicle Dimensions and weights cee 10 9 Identification number VIN 0 10 10 Loading information 10 14 Recovery freeing a stuck vehicle 6 12 A T 1 Fz 0 fn nn a 42 Ww Warning Hazard warning flasher switch 0 00 2 20 Theft Wari sis 0 c0 forcast eres fesctaterictenaatents 2 12 Warning labels Air bag warning labels 1 18 Warning light Air bag warning light 1 19 2 8 Brake warning light c cceeee eee 2 9 Door open 0 28 Low fuel warning light we 229 Seat belt warning light and chime 2 8 Warning indicator lights and chimes 2 7 Warranty Emission control system WAITAINY cecciccecvcncseasnssesiaciinaaccnaancseaansaasazsvadns 10 20 Washer switch Windshield wiper and washer SWATCH E A T E ede Washing a WAXING ereot erea E Ea EE EnC EEEE EEEN EE Weights See dimensions and weights 10 9 Wheels and tires Cleaning aluminum alloy WHOGIS is tse scceesbedvnnecainiccaranczinnczaigncgarnaczarnaczatne 7 4 Window washer fluid 00 0 c
245. y concerns Your NISSAN dealer is always available to assist you with all your automobile sales and service needs However if there is something that your NISSAN dealer cannot assist you with or you would like to provide NISSAN directly with comments or questions please contact our NISSAN s Consumer Affairs Department us ing our toll free number For U S mainland customers 1 800 NISSAN 1 1 800 647 7261 For Hawaii customers 808 836 0888 Oahu Number For Canadian customers 1 800 387 0122 The Consumer Affairs Department will ask for the following information Your name address and telephone number Vehicle identification number on dash board Date of purchase Current odometer reading Your NISSAN dealer s name Your comments or questions OR You can write to NISSAN with the information on the left at For U S mainland and Alaska customers Nissan North America Inc Consumer Affairs Department P O Box 191 Gardena California 90248 0191 For Hawaii customers Nissan Motor Corporation in Hawaii 2880 Kilihau St Honolulu Hawaii 96819 For Canada customers Nissan Canada Inc 5290 Orbitor Drive Mississauga Ontario L4W 4Z5 We appreciate your interest in NISSAN and thank you for buying a quality NISSAN vehicle Table of Contents Seats restraints and supplemental air bag systems Instruments and controls Pre driving checks and adjustments Heater air conditioner and audio s
246. y not cause harmful interference and 2 this device must accept any inter ference received including interference that may cause undesired operation of the device LIGHTS Front turn signal clearance light Trunk light Front personal tight High mounted stop light if so equipped Interior light 2 Rear side marker light late light Front fog light License plate lig if so equipped Rear combination light Stop Tail Turn and Back up lights Front side marker light SD10976 Do it yourself 8 25 HEADLIGHTS The headlight is a semi sealed beam type which uses a replaceable headlight halogen bulb A bulb can be replaced from inside the engine compartment without removing the headlight assembly AA CAUTION High pressure halogen gas is sealed inside the halogen bulb The bulb may break if the glass envelope is scratched or the bulb is dropped When handling the bulb do not touch the glass envelope 8 26 Do it yourself a Rubber cap PUSH Electrical connector SDI0967 Replacing the headlight bulb 1 Disconnect the battery negative cable 2 Disconnect the electrical connector from the rear end of the bulb 3 Pull off the rubber cap 4 Push and turn the retaining pin to loosen it 5 Remove the headlight bulb Do not shake or rotate the bulb when removing it 6 Install the new bulb in the reverse order of removal Aiming is not necessary after replacing the bulb When aim
247. ynthetic materials to reduce vehicle weight The company has also developed ways to build quality into its vehicles at each stage of the production process both through extensive use of automation and most importantly through an awareness that people are the cen tral element in quality control From the time the parts arrived from our suppli ers until you took delivery of your new Nissan dozens of checks were made to ensure that only the best job was being done in producing and delivering your vehicle NISSAN also takes great care to ensure that when you take your NISSAN to your dealer for maintenance the service tech nician will perform his work according to the quality standards that have been established by the factory Safety has also been built into your NISSAN As you know seat belts are an integral part of the safety systems that will help protect you and your passengers in the event of a sudden stop or an accident We urge you to use the seat belts every time you drive the vehicle The NISSAN story of growth and achievement reflects our major goal to provide you our customer with a vehicle that is built with quality and craftsmanship a product that we can be proud to build and you can be proud to own NISSAN CUSTOMER CARE PROGRAM NISSAN CARES Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs Your satisfaction with your vehicle and your NISSAN dealer are our primar
248. you or others to be burned The air cleaner Do it yourself 8 17 not only cleans the air it stops flame if the engine backfires If it is not there and the engine backfires you could be burned Do not drive with the air cleaner removed and be care ful when working on the engine with the air cleaner removed e Never pour fuel into the throttle body or attempt to start the engine with the air cleaner removed Doing so could result in serious injury 8 18 Do it yourself WINDSHIELD WIPER BLADES CLEANING If your windshield is not clear after using the windshield washer or if a wiper blade chatters when running wax or other material may be on the blade or windshield Clean the outside of the windshield with a washer solution or a mild detergent Your windshield is clean if beads do not form when rinsing with clear water Clean the blade by wiping it with a cloth soaked in a washer solution or a mild deter gent Then rinse the blade with clear water If your windshield is still not clear after cleaning the blades and using the wiper replace the blades PUSH to remove Lock pin REMOVE the wiper blade DI1018M REPLACEMENT 1 Pull the wiper arm 2 Push the lock pin then remove the wiper blade 3 Insert the new wiper blade to the wiper arm until a click sounds CAUTION After wiper blade replacement return the wiper arm to its original position Otherwise it may be damaged
249. yourself section AA WARNING e Your brake system may not be work ing properly if the warning light is on Driving could be dangerous If you judge it to be safe drive carefully to the nearest service station for re pairs Otherwise have your vehicle towed because driving it could be dangerous e Pressing the brake pedal with the engine stopped and or low brake fluid level may increase your stopping dis tance and braking will require greater pedal effort as well as greater pedal travel e lf the brake fluid level is below the MIN mark on the brake fluid reservoir do not drive until the brake system has been checked at a NISSAN dealer 2 If the brake fluid level is correct have the warning system checked by a NISSAN dealer ABS or Anti lock brake warning light if so equipped After turning the ignition key to the ON posi tion the light will illuminate The light will turn off after about 2 seconds if the system is operational If the light comes on while the engine is running it may indicate there is something wrong with the anti lock portion of the brake system Have the system checked by your NISSAN dealer However if the light illumi nates while starting the engine it does not indicate a system malfunction If an abnormality occurs in the system the anti lock function will cease but the ordinary brakes will continue to operate normally If the light comes on while y
250. ystems Starting and driving In case of emergency Appearance and care Do it yourself Maintenance Technical and consumer information 1 Seats restraints and supplemental air bag systems Front manual seat adjustment eee 1 2 Front power seat adjustment Folding rear Seat cieri cnisia Head restraint adjustment Are Siisera a Supplemental restraint system Precautions on supplemental restraint system 1 8 Supplemental air bag warning labels Supplemental air bag warning light Seal beltS earraun is Precautions on seat belt usage eee Child Satety crnan 1 22 Pregnant WOMEN c cccccceeseeeeeeeeseeeeteaeeteaeeteeeeeaes 1 23 Injured persons Three point type seat belt with retractor 1 24 Seat belt extenders cccceeeeeseeeeseeeeeeeeeeeteeeeee 1 27 Seat belt Maintenance eeeeceeeeeeeteeeteteeteeeee 1 27 Ghild FEStAINIS iescesisccccsscerssteeesdensssepesiecststapeciersecctess 1 28 Precautions on child restraints 1 28 Installation on rear seat outboard or center DOSIOMS 4525 22 ef ca ccc 53sec a A E E 1 30 Top tether strap child restraint if so equipped 1 35 Installation on front passenger seat 1 36 SEATS FRONT MANUAL SEAT ADJUSTMENT WARNING e Do not adjust the driver s seat while driving so full attention may be given to vehicle operation The seat may move suddenly and could cause loss of control of the v

Foreword - Nissan Extended Warranty

Contents

Download Pdf Manuals

Related Search

Related Contents