Screamin` Eagle® Street Cannon Slip
Contents
1. MOTOR HARLEY DAVIDSON WY J06095 INSTRUCTIONS REV 2015 02 18 SHORTY DUAL ACCESSORY SLIP ON MUFFLER KITS GENERAL Kit Numbers 64900342 64900343 Models For model fitment information see the P amp A retail catalog or the Parts and Accessories section of www harley davidson com English only Installation Requirements Proper installation of these kits requires separate purchase of two muffler clamps H D Part No 65296 95A IWIN NIN The rider s safety depends upon the correct installation of this kit Use the appropriate service manual procedures If the procedure is not within your capabilities or you do not have the correct tools have a Harley Davidson dealer perform the installation Improper installation of this kit could result in death or serious injury 00333a NOTE This instruction sheet refers to service manual information A service manual for this year model motorcycle is required for this installation One is available from a Harley Davidson dealer Kit Contents See Figure 1 and Table 1 PRODUCT INFORMATION Tampering Prohibition Federal law prohibits any modifications to this exhaust system which cause the motorcycle to exceed Federal noise standards Use of a motorcycle with such a modified exhaust system is also prohibited Noise Emission Warranty Harley Davidson warrants that these mufflers at the time of sale meet all applicable United States E PA Federal Noise and Emissio2. OE interconnect tube assembly Part No 66737 10A D OE muffler fastener screw 4 Part No 3391 E OE interconnect tube fastener 2 F OE interconnect gasket 2 Part No 65830 10 G OE exhaust shield 2 J06095 2of3 SERVICE PARTS is05078c Figure 1 Service Parts Shorty Dual Style Accessory Slip On Mufler Kits J06095 30f3
3. er fasteners D Tighten to 96 120 in Ibs 10 9 13 6 Nm 4 Tighten muffler clamps A to 38 43 ft lbs 51 6 58 4 Nm NOTICE Wipe all fingerprints off of exhaust system components after installation and before starting engine Oil from hands can leave permanent marks on exhaust system finish 00346a 5 Wipe exhaust system clean 6 Black exhaust system Open muffler shield clamps B Install the muffler shields 3 Position clamps so the screws are on the outboard side in the most accessible position 1 of 3 Please dispose of materials responsibly COMPLETION NOTE Verify that the ignition is OFF before installing the main fuse 1 See the service manual Install main fuse IWIN NIN After installing seat pull upward on seat to be sure it is locked in position While riding a loose seat can shift causing loss of control which could result in death or serious injury 00070b 2 See the service manual Install seat SERVICE PARTS Table 1 Service Parts Item Description Quantity Part Number 1 Muffler assembly front Not sold separately 2 Muffler assembly rear Not sold separately 3 Muffler shield black front rear 2 for black mufflers 65400078 Items mentioned in text but not included in kit A Muffler clamp 2 Part No 65296 95A Purchase separately B Original equipment OE hose clamp black 4 Part No 10800010 for black mufflers C
4. ns standards This warranty extends to the original purchaser for purposes other than resale and to all subsequent buyers Direct warranty claims to an authorized Harley Dav idson dealer NOTE To avoid penalties under state and local ordinances repair or replace this product if motorcycle noise increases significantly through use J06095 Many Harley Davidson Parts amp Accessories are made of plastics and metals which can be recycled PREPARATION IWIN NIN To prevent accidental vehicle start up which could cause death or serious injury remove main fuse before pro ceeding 00251b NOTE WITH security siren With security fob present turn ignition switch ON See the service manual After system is disarmed turn ignition switch OFF IMMEDIATELY remove the main fuse e WITHOUT security siren See the service manual Remove main fuse REMOVAL 1 See Figure 1 Loosen muffler clamps A 2 Apply penetrating oil to seams of mufflers 1 2 and exhaust pipes 3 Black exhaust system Remove muffler shield clamps B to detach muffler shields 3 from mufflers 4 ALL exhaust systems Remove muffler fasteners D to detach mufflers from muffler support C 5 Slide mufflers rearward off pipes Discard clamps A INSTALLATION 1 See Figure 1 Place new muffler clamps A over exhaust pipes 2 Slide mufflers 1 2 onto exhaust pipes 3 Align mufflers to tabs on muffler support C Install muffl
Download Pdf Manuals
Related Search