System Board D2352 for TX600 S3/RX600 S3
Contents
1. Kontakt und Supportadressen werden nun von Fujitsu Technology Solutions angeboten und haben die Form ts fujitsu com Die Internetseiten von Fujitsu Technology Solutions finden Sie unter http de ts fujitsu com und Unter http manuals ts fujitsu com finden Sie die Benutzerdokumentation Copyright Fujitsu Technology Solutions 20092. 14 D2352 TX600 S3 RX600 S3 Features PCI bus 3 3 PCI bus i a as ae Es pas m z L i gt 4 Eia o o open re yy 3 ES Lt ean a oO oO H 5 ze geh eet y 6 El E O O 7 A da m opo e Etoo gt o O AAA P Cc Zz cc IS Co E Figure 5 PCI slots PCI slots The following table shows an overview of the PCI slots PCI slot Transfer rate Description Hot plug 1 2500 Mbyte s PCI Express x8 slot yes 2 1064 Mbyte s PCI X bus slot 133 MHz yes 3 1250 Mbyte s PCI Express x4 slot yes 4 1250 Mbyte s PCI Express x4 slot yes 5 1250 Mbyte s PCI Express x4 slot yes 6 800 Mbyte s PCI X bus slot 100MHz no 7 800 Mbyte s PCI X bus slot 100MHz no Assignment of the PCI interrupts The PCI interrupts are assigned automatically by the BIOS and no further settings are possible D2352 TX600 S3 RX600 S3 15 Screen resolution Features 3 4 Screen resolution Depending on the operating system used the screen resolutions in the following table refer to the screen controller on the system board If you are using an external screen controller you will find details of supported screen resolutions in the operating manual or technical manual supplied with the
3. PIO Programmed Input Output PDB Power Distribution Board PLD Programmable Logic Device PS U Power Supply Unit PWM Pulse Wide Modulation PXE Preboot eXecution Environment 28 D2352 TX600 S3 RX600 S3 Abbreviations RAID Redundant Array of Inexpensive Disks RoHS Restriction of the Use of Certain Hazardous Substances Waste from Electric and Electronic Equipment EU Directive RoMB RAID on Motherboard RSB Remote Service Board RST ReSeT RTC Real Time Clock SCSI Small Computer Systems Interface SATA Serial Advanced Technology Attachment SDDC Single Device Data Correction SDRAM Synchronous Dynamic Random Access Memory SEL System Event Log SHDG Server Hardware Design Guide SMB System Management Bus SMM Server Management Mode D2352 TX600 S3 RX600 S3 29 Abbreviations SMP Symmetrical Multi Processing UHCI Unified Host Controller Interface USB Universal Serial Bus VGA Video Graphics Adapter VRD Voltage Regulator Down VRM Voltage Regulator Module WEEE Waste from Electric and Electronic Equipment EU Directive WfM Wired for Management WOL Wake up On LAN 30 D2352 TX600 S3 RX600 S3 ps a es ee e e eee ee Fujitsu Siemens Computers GmbH User Documentation 33094 Paderborn Germany Fax 49 700 372 00001 e mail manuals fujitsu siemens com http manuals fujitsu siemens com Comments Suggestions Corrections Subm
4. Do not throw lithium batteries into the trashcan It must be disposed of in accordance with local regulations concerning special waste Make sure that you insert the battery the right way round The plus pole must be on the top Figure 11 Replacing the lithium battery holder is similar Remove the memory board in connector A for description see the Operating Manual of your server chapter Hot plug Components gt Press the locking spring into direction of of the arrow 1 so that the lithium battery jumps out of its socket Remove the battery 2 gt Insert a new lithium battery of the same type into the socket 3 and 4 gt Reinstall the memory board in connector A D2352 TX600 S3 RX600 S3 23 Abbreviations The technical terms and abbreviations given below represent only a selection of the full list of common technical terms and abbreviations Not all technical terms and abbreviations listed here are valid for the described system board AC Alternating Current ACPI Advanced Configuration and Power management Interface ANSI American National Standards Institute ASR amp R Automatic Server Recovery and Restart ATA Advanced Technology Attachment BBU Battery Backup Unit BIOS Basic Input Output System BMC Baseboard Management Controller CMOS Complementary Metal Oxide Semiconductor COM COMmunication port CPU Central Processing Unit D2352 TX600 S3 RX60
5. LAN 2 bottom 26 J4A1 jumper 32 Dual USB connector 27 J4A2 jumper 33 Serial connector top 28 J4A3 jumper 34 Video connector bottom Settings with jumpers The system board is supplied with all jumpers set on the following positions 1 3 ONO J4A1 Password Clear EXO J4A2 BIOS Write Protect OJO J4A3 BIOS Recovery QO J4A4 NVRAM Clear ZJO J8C2 BMC Reset Figure 7 Jumper default settings J4A1 26 Password Clear 1 2 Password enabled 2 3 Password disabled cleared J4A2 27 BIOS Write Protect 1 2 BIOS unprotected 2 3 BIOS write protected J4A3 28 BIOS Recovery 1 2 Normal boot 2 3 BIOS recovery D2352 TX600 S3 RX600 S3 19 Connectors and jumpers Features J4A4 29 NVRAM Clear 1 2 NVRAM settings are not cleared 2 3 NVRAM settings cleared J8C2 1 BMC Reset 1 2 BMC enabled 2 3 BMC disabled 3 6 1 External connectors 1 2 3 5 6 AS EM ER e9 lol 4 Figure 8 External connectors I O shield 1 Video connector 4 LAN 1 2 Serial connector 5 LAN2 3 Dual USB connector LAN connectors 6 GCM connector not used On this system board you will find one GbE Broadcom LAN controller 5704C This LAN controller supports the transfer
6. the heavy metal decisive for the classification as a pollutant Cd Cadmium Hg Mercury Pb Lead D2352 TX600 S3 RX600 S3 Important notes Notes on safety Modules with electrostatic sensitive components Systems and components that might be damaged by electrostatic discharge ESD are marked with the following label A AteS When you handle components fitted with ESDs you must observe the following points under all circumstances Figure 1 ESD label e You must always discharge yourself of static charges e g by touching a grounded object before working e The equipment and tools you use must be free of static charges e Remove the power plug from the power socket before inserting or removing boards containing ESDs e Always hold boards with ESDs by their edges e Never touch pins or conductors on boards fitted with ESDs e Use a grounding cable designed for this purpose to connect yourself to the system unit as you install deinstall the board e Place all components on a static safe base You will find a detailed description for handling ESD components in the relevant European or international standards EN 61340 5 1 ANSI ESD 20 20 D2352 TX600 S3 RX600 S3 5 CE Certificate Important notes Notes about boards During installation deinstallation of the system board observe the specific instructions described in the service manual for the server Remove the plug from the mains out
7. tips Table 1 Notational conventions D2352 TX600 S3 RX600 S3 2 Important notes In this chapter you will find essential information regarding safety when working with the system board CAUTION With the system board installed you must open the system to access the system board How to dismantle and reassemble the system is described in the Options Guide accompanying your system 2 1 Notes on safety CAUTION e The actions described in these instructions should only be performed by authorized qualified personnel Equipment repairs should only be performed by qualified staff Any failure to observe the guidelines in this manual and any unauthorized openings and improper repairs could expose the user to risks electric shock fire hazards and could also damage the equipment Please note that any unauthorized openings of the device will result in the invalidation of the warranty and exclusion from all liability e Transport the device only in the antistatic original packaging or in packaging that protects it from knocks and jolts e Only install expansions that are allowed for the system board If you install other expansions you may damage the requirements and rules governing safety and electromagnetic compatibility or your system Information on which system expansions are suitable can be obtained from the customer service centre or your sales outlet e The warranty expires ifthe device is damaged during the in
8. 0 S3 25 Abbreviations DDR Double Data Rate DIMM Dual In line Memory Module DIP Dual In line Package DMI Desktop Management Interface DRAM Dynamic Random Access Memory ECC Error Correction Code EEPROM Electrical Erasable Programmable Read Only Memory EFI Extensible Firmware Interface EGB Elektrostatisch gefahrdete Bauteile EMI Electromagnetic interference EMRL Embedded RAID Logic EMV Elektromagnetische Vertraglichkeit electromagnetic compatibility EPROM Erasable Programmable Read Only Memory ESD ElectroStatic Discharge 26 D2352 TX600 S3 RX600 S3 Abbreviations EVRD Enterprise VRD HPC Hotplug Controller FPC Front Panel Controller FRU Field Replaceable Unit FSB Front Side Bus ICE In Circuit Emulation IDE Integrated intelligent Drive Electronics IEC International Electrotechnical Commission IME Integrated Mirroring Enhanced IOOP Intelligent Organisation Of PCI IPMB Intelligent Platform Management Bus IPMI Intelligent Platform Management Interface ISO International Organisation for Standardisation LAN Local Area Network D2352 TX600 S3 RX600 S3 27 Abbreviations LED Light Emitting Diode MPS Multi Processor Specification NMI Non Maskable Interrupt OEM Original Equipment Manufacturer OHCI Open Host Controller Interface OS Operating System PCI Peripheral Components Interconnect PDA Prefailure Detection and Analyzing
9. B keyboard mouse boot possible from CD DVD ROM USB drive LAN hard disk console redirection support OEM logo CPU Memory disable memory mirroring RAID spare support Environmental protection Battery in holder Form factor 16 4 x 18 3 D2352 TX600 S3 RX600 S3 13 Main memory Features 3 2 Main memory The system board offers four slots for hot plug memory boards Each memory board can be equipped with up to four memory modules in two memory banks The slots for main memory can be populated with 1 Gbyte 2 Gbyte or 4 Gbyte DDR 11 400 MHz DIMM memory modules The maximum memory is 64 Gbyte ECC with memory scrubbing and with the Single Device Data Correction SDDC function is supported You will find the descriptions how to install a memory board in the Operating Manual of your server and how to install memory modules in the Opttion Guide of your server Memory board population o AA aoc DIMM 1B fl ag ol DIMM 1A DIMM 2B E DIMM 2A Figure 4 Memory board population Start with memory bank 1 DIMM1A DIMM1B Install the memory modules in pairs All DIMMs in a pair must be of the same type and size The module capacity between pairs can differ pair 2A 2B can be populated with two 1 Gbyte modules and pair 1A 1B with two 2 Gbyte modules
10. Lead The following applies to Germany Private consumers can return batteries at the point of sale or the immediate vicinity thereof free of charge exception starter batteries The final consumer is obligated to return defective or used batteries to the seller or to the return points established for this purpose Local contacts For details on take back and reuse of devices and consumables within Europe contact your Fujitsu Siemens Computers branch office subsidiary or our recycling center in Paderborn Fujitsu Siemens Computers Recycling Center D 33106 Paderborn Germany Tel 49 5251 8 18010 Fax 49 5251 8 18015 Internet www fujitsu siemens com recycling D2352 TX600 S3 RX600 S3 9 3 Features 3 1 Overview System board e Up to four Intel XEON MP dual core processors e Intel E8501 chipset Intel E8501 chipset Northbridge TNB has two shared 64 bit FSB interfaces configured for symmetric multiprocessing External Memory Board XMB provides support for DDR 2 memory PXH provides support for PCI X Intel 1IOP332 1 0 processor with Intel XScale Microarchitecture provides support for PCI X and contains Intel XScale technology to support RoMB RAID on Motherboard Intel 82801EB I O controller Hub 5 Southbridge provides support for system BIOS USB 2 0 and SATA e Advanced I O architecture One hot plug x8 PCI Express slot Three hot plug x4 PCI Expres
11. ave to be on permanently should not be switched on until they need to be used and should be switched off during long breaks and on completion of work Notes on packaging Please do not throw away the packaging You may need it later for transporting your system unit If possible the device should only be transported in its original packaging Notes on dealing with consumables Please dispose batteries in accordance with local government regulations Do not throw lithium batteries into the household waste They must be disposed of in accordance with local regulations concerning special waste Notes on labeling plastic housing parts Please avoid attaching your own labels to plastic housing parts wherever possible since this makes it difficult to recycle them D2352 TX600 S3 RX600 S3 7 Environment Protection Important notes Returning used electrical and electronic devices in EU countries Separate collection Users of electrical and electronic devices are obligated to collect used devices separately Electrical electronic used devices may not be disposed of together with unsorted household refuse The separate collection is a condition for reuse recycling and utilisation of used electrical electronic devices which ensures the protection of resources Return and collection systems Electrical electronic used devices from private households can be returned free of charge To return your used device please use the count
12. controller Screen resolution Refresh rate Digital Display Max number of colours Hz Hz 640x480 200 75 16 7 Mio 800x600 200 75 16 7 Mio 1024x768 200 75 16 7 Mio 1152x864 150 16 7 Mio 1280x1024 130 75 16 7 Mio 1600x1200 90 60 16 7 Mio 3 5 Temperature system monitoring Temperature and system monitoring aim to reliably protect the computer hardware against damage caused by overheating In addition any unnecessary noise is also prevented by reducing the fan speed and information is provided about the system status The temperature and system monitoring are controlled by an onboard controller The following functions are supported Temperature monitoring Measurement of the processor temperature measurement of the ambient temperature by a temperature sensor on the LED board 16 D2352 TX600 S3 RX600 S3 Features Temperature system monitoring Fan monitoring Fans that are no longer available blocked or sticky fans are detected Fan control The fans are regulated according to temperature Maximum speed if the housing cover has been opened Sensor monitoring The removal of or a fault in a temperature sensor is detected Should this happen all fans monitored by this sensor run at maximum speed to achieve the greatest possible protection of the hardware Voltage monitoring When voltage exceeds warning level high or falls below warning level low an aler
13. itted by Comments on System Board D2352 for TX600 S3 RX600 S3 D2352 TX600 S3 RX600 S3 O FUJITSU Information on this document On April 1 2009 Fujitsu became the sole owner of Fujitsu Siemens Compu ters This new subsidiary of Fujitsu has been renamed Fujitsu Technology So lutions This document from the document archive refers to a product version which was released a considerable time ago or which is no longer marketed Please note that all company references and copyrights in this document have been legally transferred to Fujitsu Technology Solutions Contact and support addresses will now be offered by Fujitsu Technology So lutions and have the format ts fujitsu com The Internet pages of Fujitsu Technology Solutions are available at http ts fujitsu com and the user documentation at http manuals ts fujitsu com Copyright Fujitsu Technology Solutions 2009 Hinweise zum vorliegenden Dokument Zum 1 April 2009 ist Fujitsu Siemens Computers in den alleinigen Besitz von Fujitsu Ubergegangen Diese neue Tochtergesellschaft von Fujitsu tr gt seit dem den Namen Fujitsu Technology Solutions Das vorliegende Dokument aus dem Dokumentenarchiv bezieht sich auf eine bereits vor langerer Zeit freigegebene oder nicht mehr im Vertrieb befindliche Produktversion Bitte beachten Sie dass alle Firmenbez ge und Copyrights im vorliegenden Dokument rechtlich auf Fujitsu Technology Solutions bergegangen sind
14. let so that system and system board are totally disconnected from the mains voltage To prevent damage to the system board the components and conductors on it please take great care when you insert or remove boards Take great care to ensure that extension boards are slotted in straight without damaging components or conductors on the system board or any other components for example EMI spring contacts Be careful with the locking mechanisms catches centring pins etc when you replace the system board or components on it for example memory modules or processors Never use sharp objects screwdrivers for leverage 2 2 CE Certificate The shipped version of this board complies with the requirements of the EEC directive 89 336 EEC Electromagnetic compatibility Compliance was tested in a typical PRIMERGY configuration D2352 TX600 S3 RX600 S3 Important notes Environment Protection 2 3 Environment Protection Environmentally friendly product design and development This product has been designed in accordance with the Fujitsu Siemens Computers standard for environmentally friendly product design and devel opment This means that key factors such as durability selection and labeling of materials emissions packaging ease of disassembly and recycling have been taken into account This saves resources and thus reduces the harm done to the environment Notes on saving energy Devices that do not h
15. rates of 10 Mbit s 100 Mbit s and 1 Gbit s The LAN controller supports WOL function through Magic Packet It is also possible to boot a device without its own boot hard disk via LAN Here Intel PXE is supported 20 D2352 TX600 S3 RX600 S3 Features RoMB The LAN controller connectors are equipped with two LEDs light emitting diode indicating the transfer rate and the activity 1 2 Figure 9 LAN connectors 1 LAN link aktivity green on LAN connection off no LAN connection flashing LAN transfer 2 LAN transfer rate off transfer rate 10 Mbit s or no connection green on transfer rate 100 Mbit s orange on transfer rate 1000 Mbit s 3 7 RoMB The onboard Intel IOP332 I O processor becomes a RAID5 RAID O 1 5 10 50 controller by using a RAID activation key and a cache module The following figure shows the installed components Figure 10 e 1 RAID activation key 2 cache module D2352 TX600 S3 RX600 3 21 4 Replacing the lithium battery In order to save the system information permanently a lithium battery is installed to provide the CMOS memory with a current When the charge is too low or the battery is empty a corresponding error message is provided The lithium battery must then be replaced The lithium battery must be replaced with an identical battery or a battery type recommended by the manufacturer CR2032
16. ry specific return and collection systems available to you see Local contacts on page 9 The return of used devices which pose a health or safety risk for human beings due to soiling during use may be refused Reuse recycling and utilisation By actively using the offered return and collection systems you make your contribution to the reuse recycling and utilisation of electrical electronic devices Effects on the environment and human health Electrical electronic used devices contain parts which must be handled selectively according to the EU directive Separate collection and selective treatment are the basis for environment friendly disposal and the protection of human health Meaning of the symbol Crossed out rubbish bin on wheels Electrical electronic devices which are marked with one of the following symbols may not be disposed of with household refuse in accordance with the EU directive Figure 2 Symbols for electrical electronic devices D2352 TX600 S3 RX600 S3 Important notes Environment Protection Returning batteries Batteries which are marked with one of the following symbols may not be disposed of together with household refuse according to the applicable EU directive Figure 3 Symbols for batteries With batteries containing harmful substances the chemical symbol for the heavy metal contained is indicated below the waste bin Cd Cadmium Hg Mercury Pb
17. s slots One hot plug 133 MHz 64 bit PCI X slot Two 100 MHz 64 bit PCI X slots not hot plug e LSI Logic 53C1030 LVD SCSI controller Dual independent U320 SCSI interfaces 64 bit PCI X 100 Mhz interface e Integrated ATI Technologies Inc Radeon 7000M with 16 MB embedded SDRAM D2352 TX600 S3 RX600 S3 11 Overview Features e USB 2 0 support Two ports at the rear of the chassis Three ports at the front of the chassis One port onboard Main memory Up to 4 hot plug memory boards with each 4 slots for main memory PC2 3200 DDRII 400 MHz DIMM memory modules with 1 Gbyte 2 Gbyte and 4 Gbyte Maximum 64 Gbyte of memory Memory mirroring function or memory RAID Optional hot spare memory function Single Device Data Correction SDDC function Chipkill External connectors Front side front panel 3x USB 2 0 ports 1x VGA port 15 pin Rear side I O shield 2x USB 2 0 ports 1x VGA port 15 pin 1x RS 232 C interface serial 9 pin 2x RJ45 LAN ports onboard LAN 1x RJ45 LAN port presently not used reserved for future development BIOS features Intel Platform Innovation Framework EFI BIOS MultiProcessor Specification 1 4 Server Hardware Design Guide 3 0 WfM 2 0 IPMI V1 5 ACPI 1 0b support 12 D2352 TX600 S3 RX600 S3 Features Overview Intel RoMB BIOS LSI SCSI BIOS SATA support US
18. stallation or replacement of system expansions D2352 TX600 S3 RX600 S3 3 Notes on safety Important notes N Batteries Components can become very hot during operation Ensure you do not touch components when making extensions to the system board There is a danger of burns Transmisson lines to peripheral devices must be adequately shielded To the LAN wiring the requirements apply in accordance with the standards EN 50173 and EN 50174 1 2 As minimum requirement the use of a protected LAN line of category 5 for 10 100 MBps Ethernet and or of category 5e for Gigabit Ethernet is considered The requirements of the specification ISO IEC 11801 are to be considered Never connect or disconnect data transmission lines during a storm lightning hazard CAUTION Incorrect replacement of lithium battery may lead to a risk of explosion The batteries may only be replaced with identical batteries or with a type recommended by the manufacturer It is essential to observe the instructions in chapter Replacing the lithium battery on page 23 Do not throw batteries into the trash can They must be disposed of in accordance with local regulations concerning special waste The battery must be disposed of in accordance with local regulations concerning special waste All batteries containing pollutants are marked with a symbol a crossed out garbage can In addition the marking is provided with the chemical symbol of
19. system Board D2352 for TX600 S3 RX600 S3 Technical manual Edition December 2006 Comments Suggestions Corrections The User Documentation Department would like to know your opinion of this manual Your feedback helps us optimize our documentation to suit your individual needs Fax forms for sending us your comments are included in the back of the manual There you will also find the addresses of the relevant User Documentation Department Certified documentation according to DIN EN ISO 9001 2000 To ensure a consistently high quality standard and user friendliness this documentation was created to meet the regulations of a quality management system which complies with the requirements of the standard DIN EN ISO 9001 2000 cognitas Gesellschaft f r Technik Dokumentation mbH www cognitas de Copyright and Trademarks Copyright 2006 Fujitsu Siemens Computers GmbH All rights reserved Delivery subject to availability right of technical modifications reserved All hardware and software names used are trademarks of their respective manufacturers Contents 1 Introduction 2 Important notes 2 1 Notes on safety 2 2 CE Certificate 2 3 Environment Protection 3 Features 22222000 3 1 Overview 3 2 Main memory 3 3 PCI DUS 2628 ea 0 40 4 3 4 Screen resolution 3 5 Temperature system monitoring 3 6 Connectors and j
20. t will be generated System Event Log SEL All monitored events of the system board are recorded in the System Event Log They could be retrieved after a system reboot via ServerView D2352 TX600 S3 RX600 3 17 Connectors and jumpers Features 3 6 Connectors and jumpers 8 9 ae O O me i me O o Oo o a Hi 11 O o H o O a 12 O O o O Ba 13 O O De 23 22 21 20 19 18 17 16 15 14 Figure 6 Schematic overview of the system board D2352 1 J8C2 jumper 2 Memory board connector B 3 Memory board connector A 4 Battery 5 SATA connector 6 BMC connector 7 Front panel connector 8 PDB signal connector 9 DC power connectors 10 Processor socket 1 11 Processor socket 2 12 Processor socket 4 13 Processor socket 3 14 SCSI connector channel A 15 VRM 9 1 connector for future use 16 VRM 10 2 connector CPU 4 17 VRM 10 2 connector CPU 3 18 SCSI connector channel B 19 RAID DDR2 DIMM connector RoMB 20 Memory board connector D 21 Memory board connector C 22 USB onboard connector 18 D2352 TX600 S3 RX600 S3 Features Connectors and jumpers 23 IPMI connector 29 J4A4 jumper 24 GCM connector not used 30 LAN 1 top 25 RAID Activation Key RoMB 31
21. umpers 3 6 1 External connectors 3 7 RoMB osos 4 Replacing the lithium battery Abbreviations D2352 TX600 S3 RX600 S3 1 Introduction This technical manual describes the system board D2352 which can be equipped with up to four Intel processors Further information about drivers is provided in the readme files on the supplied ServerSupport or ServerStart CDs You will find further information in the manual D2352 Setup Utility Notational conventions The meanings of the symbols and fonts used in this manual are as follows italics indicates commands menu items file and path names or software programs fixed font indicate system output on the monitor semi bold fixed indicates values to be entered through the keyboard font Key symbol indicates keys according to their representation on the keyboard If capital letters are to be entered explicitly then the Shift key is shown e g SHIFT A for A If two keys need to be pressed at the same time then this is shown by placing a hyphen between the two key symbols quotation marks indicates names and terms that are being empha sized indicates an operation that to be performed gt A CAUTION indicates warnings which if ignored will endanger your health destroy the system or lead to the loss of data il indicates additional information notes and
Download Pdf Manuals
Related Search