Trophy and Trophy SE A9708259, A9708276, A9708350, A9708351
Contents
1. f a NANIA 1 Sub harness 2 Power connector 3 Motorcycle frame JAA Ly A T1239 23 Route the sub harness up into the rear undertray be ae pone 2 Fir tree clip round the under w xX around the under seat stowage bo 3 Location hole 25 Press the fir tree clip in to the hole to secure the heated seat power socket to the mudguard undertray 26 Secure the sub harness to the rear undertray with the cable clips from the kit T1254a a 2 a TT oe 1 Sub harness 2 Rear undertray 3 Under seat stowage box o o SS T1238 1 Sub harness 2 Rear undertray 3 Cable clip 13 of 15 27 Locate the rider seat connection on the pillion seat sub harness situated next to the main wiring harness connector Remove the blanking plug and connect the rider seat sub harness to the socket Retain the blanking plug for re use if the motorcycle is returned to original condition 1 Rider seat connection pillion seat sub harness 2 Rider seat sub harness connector 28 Route the rider heated seat switch connector on the sub harness back behind the frame towards the rear of the motorcycle up to the rear left hand side of the rear undertray 1 Heated seat switch connector 2 Motorcycle frame 29 30 Refit the left hand side pan2. 1 Sub harness 1 Sub harness 2 Power connector with fir tree clip 2 Rear undertray 3 Motorcycle frame 3 Under seat stowage box 3 of 15 9 Keeping the sub harness above any existing wiring harnesses route around the right hand side of the rear undertray until the fir tree clip on the power connector is aligned with the front location hole 3 in the rear undertray T1239 E ee l 1 Power connector 2 Fir tree clip 3 Location hole 10 Press the fir tree clip into the hole to secure the heated seat power socket to the mudguard undertray 11 Secure the sub harness to the rear undertray with the cable clips from the kit Le Z SN 1 Sub harness 2 Rear undertray 3 Cable clip Note e Ifa heated pillion seat is not fitted continue from step 14 12 If a heated pillion seat is fitted locate the rider seat connection on the pillion seat sub harness situated next to the main wiring harness connector 13 Remove the blanking plug and connect the rider seat sub harness to the socket Retain the blanking plug for re use if the motorcycle is returned to original condition Continue from step 16 D 1 Rider seat connection pillion seat sub harness 2 Rider seat sub harness connector 14 Locate the heated seat connection on the main harness situated next to the fuse block The connector will be fitted with a blank
3. English TRIUMPH Fitting Instructions Trophy and Trophy SE A9708259 A9708276 A9708350 A9708351 and A9708260 Thank you for choosing this Triumph genuine accessory kit This accessory kit is the product of Triumph s use of proven engineering exhaustive testing and continuous striving for superior reliability safety and performance Completely read all of these instructions before commencing the installation of the accessory kit in order to become thoroughly familiar with the kit s features and the installation process These instructions should be considered a permanent part of your accessory kit and should remain with it even if your accessory equipped motorcycle is subsequently sold 1 NJ 4 4 1 Rider seat heated 1 off 3 Switch 1 off 2 Sub harness 1 off 4 Cable clip 2 off Parts Supplied A9708259 A9708276 A9708350 and A9708351 3 18 Ss Parts Supplied A9708260 1 Pillion seat heated 1 off 3 Switch 1 off 2 Sub harness 1 off 4 Cable clip 2 off Publication part number A9900623 issue 2 DC 66511 1 of 15 Triumph Designs Ltd 2014 This accessory kit is designed for use on Triumph Trophy and Trophy SE motorcycles only and should not be fitted to any other Triumph model or any other manufacturer s motorcycle Fitting this accessory kit to any other Triumph model or any other manufacturer s motorcycle will affect the performance stabi
4. Heated Pillion Seat on page 6 e f fitting the heated rider and pillion seats continue from Heated Rider and Pillion Seats on page 9 After fitting any seat combination carry out the Heated Seat System Testing on page 75 Heated Rider Seat 1 Remove the rider seat as described in the owner s handbook Retain the rider seat for re use if the motorcycle is returned to original condition Retain the pillion seat for re use 2 Disconnect the battery as described in the service manual 3 Remove the left hand side panel as described in the service manual 4 Remove the switch blanking plug carefully pressing the plug out from the underside of the panel to prevent damage Retain the blanking plug for re use if the motorcycle is to be returned to its original condition 1 Side panel 2 Blanking plug 2 of 15 5 Fit the heated seat switch provided to the side panel in 7 Route the sub harness power connector back up the orientation shown below behind the frame into the rear undertray area T1241 1 Side panel 1 Sub harness 2 Heated seat switch 2 Power connector Mot le fi 6 Feed the sub harness power connector with fir tree 3a Motoreye mame clip first down past the fuse box and behind the frame 8 Route the sub harness up into the rear undertray as shown around the under seat stowage box Ps T1245 LA PEA
5. an accident Remember that the 80 mph 130 km h limit will be reduced by the fitting of non approved accessories incorrect loading worn tyres overall motorcycle condition and poor road or weather conditions 15 of 15
6. ce manual Ensure the harness for the heated seat does not become trapped between the seat and the motorcycle frame Refer to the owners handbook for details regarding the operation of the heated seats 5 of 15 Heated Pillion Seat When removing the seats for any reason always disconnect the heated seat harness Do not allow the heated seats to hang freely on the sub harness as this would result in irreparable damage to the heated seat 1 Remove the pillion seat as described in the owner s handbook Retain the pillion seat for re use if the motorcycle is returned to original condition Retain the rider seat for re use 2 Disconnect the battery as described in the service manual Note e Ifa heated rider seat is fitted disconnect the heated seat switch before removing the left hand side body panel 3 Remove the luggage rack as described in the service manual 4 Remove the left hand side panel and right hand rear panel as described in the service manual 5 Remove the switch blanking plug carefully pressing the plug out from the underside of the panel to prevent damage Retain the blanking plug for re use if the motorcycle is returned to original condition 1 2 o J 1 Rear panel 2 Blanking plug 6 Fit the heated seat switch provided in to the rear panel in the orientation shown below 1 Rear panel 2 Heated seat switch 7 Feed the sub harness seat switch connector and power c
7. ed to original condition 2 Disconnect the battery as described in the service manual 3 Remove the luggage rack as described in the service manual 4 Remove the left hand side panel and right hand rear panel as described in the service manual 5 Remove the switch blanking plug from the left hand side panel carefully pressing the plug out from the underside of the panel to prevent damage Retain the blanking plug for re use if the motorcycle is returned to original condition E D EF r T1240 1 Side panel 2 Blanking plug 9 of 15 6 Fit the one of the heated seat switches provided in to 8 Fit the second heated seat switch provided in to the the left hand side panel in the orientation shown right hand rear panel in the orientation shown below below Ti 1 Rear panel 1 Side panel 2 Heated seat switch 2 Heated seat switch Pillion Seat Sub Harness Installation 9 Feed the sub harness seat switch connector and power connector with fir tree clip first down past the fuse box and behind the frame as shown N Remove the switch blanking plug from the right hand rear panel carefully pressing the plug out from the underside of the panel to prevent damage Retain the blanking plug for re use if the motorcycle is returned to original condition j J AA 4 CK a TTA A CLANN Y io Y VSIA 1 Sub harness T1240a 1 Rear panel 2 Power connector with fir tree clip 2 Blanking plug 3 Seat
8. el as described in the service manual ensuring the heated seat switch connector is routed behind the frame in to the rear undertray area Connect the rider heated seat switch connector to the heated seat sub harness Note ae LLON o a Ea Hh Tiner fom T H7 The heated rider seat power socket can be identified by red tape on the harness am N a s EN es 3 7S aia N TN TK oes LMA 2 iS ee TH aaa Dum int zane Loe 1 Pillion seat power socket 2 Rider seat power socket 3 Red identification tape 31 32 33 34 35 Connect the heated pillion seat connector to the pillion seat power socket Connect the rider seat connector to the rider seat power socket Reconnect the battery as described in the service manual Refit the rider and pillion seats as described in the owner s handbook Ensure the harnesses for the heated seats do not become trapped between the seat and the motorcycle frame Refer to the owner s handbook for details regarding the operation of the heated seats 14 of 15 Heated Seat System Testing The motorcycle must not be operated above the legal road speed limit except in closed course conditions Never start the engine or let it run for any length of time in a closed area The exhaust fumes are poisonous and may cause loss of consciousness and death within a short time Always operate the mo
9. ing plug S 4 XK 1 Blanking plug heated seat connector 4 of 15 15 Remove the blanking plug from the heated seat connection on the main wiring harness and connect the rider seat sub harness Retain the blanking plug for re use if the motorcycle is returned to original condition 1 Sub harness connector 2 Heated seat connection 16 Note e If a heated pillion seat is fitted the rider seat power socket can be identified by red tape on the harness ise ZI AS J Ti 2 TR ea ae Pst es Se paame J L WS cd WL e a LN o gt o Sa uy iN 1 Pillion seat power socket 2 Rider seat power socket 3 Red identification tape Route the rider heated seat switch connector on the 19 sub harness back behind the frame towards the rear i of the motorcycle up to the left hand side rear of the rear undertray 20 21 22 1 Heated seat switch connector 2 Motorcycle frame 17 Refit the left hand side panel as described in the service manual ensuring the heated seat switch connector is routed behind the frame in to the rear undertray area 18 Connect the rider heated seat switch connector to the heated seat sub harness Connect the heated rider seat connector to the rider seat power socket Reconnect the battery as described in the service manual Refit the rider and pillion seats as described in the servi
10. is to be returned to its original condition 1 Sub harness connector 2 Heated seat connection 16 Refit the right hand rear panel as described in the service manual 17 Refit the luggage rack as described in the service manual 18 Route the heated seat switch wiring on the sub harness along the right hand side of the frame over the luggage rack towards the rear of the motorcycle 19 Connect the pillion heated seat switch connector to the heated seat sub harness 1 Heated seat switch connector 2 Sub harness switch connector 20 Ensure the switch connector wiring is retained to the luggage rack as shown below 1 Luggage rack 2 Heated seat switch wiring Rider Seat Sub Harness Installation 21 Feed the sub harness power connector with fir tree clip first down past the fuse box and behind the frame as shown 1 Sub harness 2 Power connector with fir tree clip 3 Motorcycle frame 12 of 15 24 Keeping the sub harness above any existing wiring harnesses route around the right hand side of the rear undertray until the fir tree clip on the power connector is aligned with the front location hole 3 in the rear undertray 22 Route the sub harness power connector back up behind the frame into the rear undertray area a 7 ry N a i f by OY i K av ITH Q Soc 37 TW VACA N GA AS aN ay S AA a
11. lion seat sub harness connector 13 Locate the rider seat connection on the pillion seat sub harness Remove the blanking plug and connect the rider seat sub harness to the socket Retain the blanking plug for re use if the motorcycle is returned to original condition Continue from step 16 Bal lt gt 2 d e2 Dor 1 Rider seat connection pillion seat sub harness 2 Rider seat sub harness connector 3 Sub harness connector pillion seat 4 Heated seat connection A N iN 7 of 15 14 Locate the heated seat connection on the main harness situated next to the fuse block The connector will be fitted with a blanking plug se ae A Ss 1 Blanking plug heated seat connection s 5 Remove the blanking plug from the heated seat connector on the main wiring harness and connect the pillion seat sub harness Retain the blanking plug for re use if the motorcycle is returned to original condition 1 Sub harness connector 2 Heated seat connection 16 Refit the left hand panel as described in the service manual 17 Refit the right hand rear panel as described in the service manual 18 Refit the luggage rack as described in the service manual 19 Route the heated seat switch wiring on the sub harness along the right hand side of the frame over the luggage rack towards the rear of the motorcycle 20 Connect the pillion heated seat switch connector to the heated seat sub har
12. lity and handling of the motorcycle This may affect the rider s ability to control the motorcycle and could cause an accident Always have Triumph approved parts accessories and conversions fitted by a trained technician of an authorised Triumph dealer The fitment of parts accessories and conversions by a technician who is not of an authorised Triumph dealer may affect the handling stability or other aspects of the motorcycle s operation which may result in loss of motorcycle control and an accident Always ensure that the newly installed wiring does not chafe against other parts of the motorcycle such that it may be rubbed through and cause an electrical problem In addition always ensure that the newly installed wiring will not restrict steering movement Both conditions are hazardous and could give rise to a dangerous riding condition resulting in a fire loss of motorcycle control and an accident Throughout this operation ensure that the motorcycle is stabilised and adequately supported to prevent risk of injury from the motorcycle falling When removing the seats for any reason always disconnect the heated seat harness Do not allow the heated seats to hang freely on the sub harness as this would result in irreparable damage to the heated seat Note e If fitting the heated rider seat only continue as described below e If fitting the heated pillion seat only continue from
13. ness 1 Heated seat switch connector 2 Sub harness switch connector 21 Ensure the switch connector wiring is retained to the luggage rack as shown below 1 Luggage rack 2 Heated seat switch wiring 8 of 15 Note e If a heated rider seat is fitted the rider seat power socket can be identified by red tape on the harness L N 1 Pillion seat power socket 2 Rider seat power socket 3 Red identification tape 22 Connect the heated pillion seat connector to the pillion seat power socket 23 If a heated rider seat is fitted connect the rider seat connector to the rider seat power socket 24 Reconnect the battery as described in the service manual 25 Refit the rider and pillion seats as described in the owner s handbook Ensure the harness for the heated seat does not become trapped between the seat and the motorcycle frame 26 Refer to the owner s handbook for details regarding the operation of the heated seats Heated Rider and Pillion Seats When removing the seats for any reason always disconnect the heated seat harness Do not allow the heated seats to hang freely on the sub harness as this would result in irreparable damage to the heated seat a Remove the rider and pillion seats as described in the owner s handbook Retain the rider and pillion seats for re use if the motorcycle is return
14. onnector with fir tree clip first down past the fuse box and behind the frame as shown 1 Sub harness 2 Power connector with fir tree clip 3 Seat switch connector 4 Motorcycle frame 6 of 15 8 Route the sub harness seat switch harness and power connector back up behind the frame into the rear undertray area TA 1 Sub harness 2 Power connector 3 Seat switch 4 Motorcycle frame 9 Keeping the sub harness above any existing wiring harnesses route the sub harness including the switch connector around the under seat stowage box to the right hand side of the rear undertray until the fir tree clip on the power connector is aligned with the rear location hole 3 in the rear undertray 71254 a 1 Sub harness 2 Power connector 3 Location hole 4 Rear undertray 5 Under seat stowage box 10 Press the fir tree clip in to the hole to secure the heated seat power socket to the rear undertray 11 Secure the sub harness to the rear undertray with the cable clips from the kit aa 1 Sub harness 2 Rear undertray 3 Cable clip Note If a heated rider seat is not fitted continue from step 14 12 If a heated rider seat is fitted remove the rider seat sub harness connector from the main wiring harness heated seat connection and replace with the pil
15. switch connector 4 Motorcycle frame 10 of 15 10 Route the sub harness seat switch harness and power 13 Secure the sub harness to the rear undertray with the connector back up behind the frame into the rear cable clips from the kit undertray area DA LS 5 1 Sub harness 1 Sub harness 2 Rear undertray 2 Power connector 3 Cable clip 3 Seat switch 14 Locate the heated seat connection on the main 4 Motorcycle frame harness situated next to the fuse block The connector 11 Keeping the sub harness above any existing wiring will be fitted with a blanking plug harnesses route the sub harness including the switch connector around the under seat stowage box to the right hand side of the rear undertray until the fir tree clip on the power connector is aligned with the rear location hole 3 in the rear undertray 1 Blanking plug heated seat connector 1 Sub harness 2 Power connector 3 Location hole 4 Rear undertray 5 Under seat stowage box 12 Press the fir tree clip in to the hole to secure the heated seat power socket to the rear undertray 11 of 15 15 Remove the blanking plug from the heated seat connector on the main wiring harness and connect the pillion seat sub harness Retain the blanking plug for re use if the motorcycle
16. torcycle in the open air or in an area with adequate ventilation Only operate this Triumph motorcycle at high speed in closed course on road competitions or on closed course 1 Run the engine to avoid draining the battery racetracks High speed operation should only be 2 Operate the switch at both positions and check that the attempted by riders who have been instructed in the heated seat s warm up techniques necessary for high speed riding and are 3 The fuse number 1 of the front fuse box protects the familiar with the motorcycles characteristics in all heated seat circuit Refer to the label in the fuse box lid conditions for fuse amperage High speed operation in any other circumstances is dangerous and will lead to loss of motorcycle control and an accident If after fitment of this accessory kit you have any doubt about the performance of any aspect of the motorcycle contact an authorised Triumph dealer and do not ride the motorcycle until the authorised dealer has declared it fit for use Riding a motorcycle when there is any doubt as to any aspect of the performance of the motorcycle may result in loss of control of the motorcycle leading to an accident Never ride an accessory equipped motorcycle at speeds above 80 mph 130 km h The presence of accessories will cause changes in the stability and handling of the motorcycle Failure to allow for changes in motorcycle stability may lead to loss of control or
Download Pdf Manuals
Related Search