VOLUNTARY SERVICE CAMPAIGN BODY CONTROL MODULE
Contents
1. CLAIMS INFORMATION Submit a Campaign CM line claim using the following claims coding CM I D P5234 Titan A60 amp Armada TA60 DESCRIPTION OP CODE FRT Install BCM Sub Harness P52340 0 4 hrs Xterra N50 Pathfinder R51 amp Frontier D40 DESCRIPTION OP CODE FRT Install BCM Sub Harness P52342 0 5 hrs OR Titan A60 amp Armada TA60 DESCRIPTION OP CODE Install BCM Sub Harness amp RPL BCM Controller P52341 0 9 hrs Xterra N50 Pathfinder R51 amp Frontier D40 DESCRIPTION OP CODE FRT Install BCM Sub Harness amp RPL BCM Controller P52343 1 0 hrs 15 16 OWNER S LETTER Dear Nissan Owner Nissan is committed to providing the highest levels of product quality and customer satisfaction We know that towing a trailer may have been an important consideration in your vehicle s purchase In new Titan Armada Pathfinder Frontier and Xterra vehicles Nissan recently introduced enhanced electronic circuitry which may help further protect your vehicle from damage or fire caused by a short circuit in the electrical system of a towed trailer due to problems with the trailer s wiring or mis installation of trailer lighting or electrical accessories This is to advise you that Nissan is making this production enhancement available to you free of charge so that you will have the same protection should you ever tow a trailer with a defective electrical system What You Should Do To take advantage o2. Steering Shaft only for BCM Coupling N replacement Mounting B Body Control Module BCM BCM Harness Connectors Disconnect for installing BCM sub harness TPO50654 8 Connect the fuse end of the BCM Sub Harness to the BCM as shown in Figure 7 e Make sure the connectors are securely connected snapped in place to the BCM CO is Mi ie A TP050655 Figure 7 7 16 9 At the other end of the BCM Sub Harness e Connect the White Connector to the vehicle side harness white connector see Figure 8a e Then connect the Black Connector to the vehicle side harness black connector see Figure 8b Harness Black BCM Sub Connector Harness White Vehicle Side Connector BCM White Connector TPO50656 TPO50657 Figure 8a Figure 8b 10 Secure the new BCM Sub Harness to the Existing Vehicle Harness see Figure 9 e Use the Tie Wrap that comes already attached to the new Sub Harness Figure 9 11 Re connect the negative battery cable 12 Confirm the installed BCM Sub Harness does not interfere with the operation of the adjustable pedal assembly NOTE It is okay if the BCM Sub Harness has slight contact with the adjustable pedal assembly when the pedal assembly is adjusted to the end of its upward travel closest to the driver 8 16 13 For vehicles without a trailer lights wiring connector confirm BCM operation as follows a b C Turn the ignition switch O
3. Panel Lower Cover see Figure 13 e Carefully pull the Cover rearward to release the Securing Clips e Disconnect all Harness Connectors from the Lower Cover Ke U aS Driver s Side Instrument Panel Lower Cover Remove TP050642 Figure 13 11 16 7 Remove two Bolts and remove the Knee Protector Brace see Figure 14 Knee Protector Brace TP050643 Figure 14 8 If the BCM needs to be replaced as confirmed by Procedure A Terminal Check go ahead and replace the BCM now Then continue with step 10 next page e Remove all three Harness Connectors from the BCM see Figure 15 e Remove the two BCM Mounting Bolts and remove BCM see Figure 15 e Install the new BCM e Reconnect the RH connector ONLY as viewed in Figure 15 9 If the BCM does not need to be replaced e Install the new Sub Harness e Start by disconnecting ONLY the two horizontal Connectors at the BCM see Figure 15 BCM Connector Disconnect ONLY When Replacing BCM VETE NAY Shaft 8 Ye 4 Coupling XS AL Nat Ve BCM Mounting D AD Q4 f VAS Bolts Remove ONLY when replacing BCM Disconnect for BCM Sub Harness Installation N e ar AB Front O Body Control OW Module BCM TP050644 Figure 15 12 16 10 Connect the fuse end of the BCM Sub Harness to the BCM as shown in Figure 16 e Make sure the connectors are securely connected Snapped in place to the BCM 1 Ke PRS VOM La N
4. F 3 Using a Test Light check for power at terminals 2 and 5 see Figure 2 e If there is power at either terminal replace the BCM Return to the Repair Flow Chart for further instructions e If there is NO power at either terminal the circuit is OK Return to the Repair Flow Chart for further instructions Test Light Comes ON When Touching 2 or 5 7 Terminal Trailer Lights Wiring Connector Trailer Hitch Test Light Does Not Come ON When Touching 2 or 5 TP050659a Figure 2 4 Turn the ignition switch OFF 4 16 PROCEDURE B BCM SUB HARNESS INSTALLATION amp BCM REPLACEMENT NOTE Procedure B Sub Harness Install BCM Replace is split up into two sections e Section 1 For Titan Armada vehicles e Section 2 For Pathfinder Frontier Xterra vehicles CAUTION Use suitable covers to protect upholstery carpet trim etc when performing this procedure Section 1 Titan Armada Procedure 1 If you determined the BCM needs to be replaced from Procedure A Terminal Check e First perform BCM Read Configuration using CONSULT II e Todo this refer to READ CONFIGURATION PROCEDURE in section BCS in the applicable service manual 2 Record all radio station presets and then disconnect the negative battery cable CAUTION The complete repair needs to be conducted within one hour of disconnection of the battery If the battery is left disconnected for longer than one hour the idle setting m
5. N Place your hand on the new BCM Sub Harness Activate the left turn indicator blinker and confirm a click is felt heard each time the left turn indicator light flashes Activate the right turn indicator blinker and confirm a click is felt heard each time the right turn indicator light flashes Apply the brake pedal and confirm a click is felt heard when the brake lights come on If you feel hear a clicking noise when performing steps c d and e go to the next step If you do not feel hear a clicking noise when performing steps c d and e replace the BCM then go to the next step 14 Re install all components in reverse order of removal 15 Re program all radio station presets 16 If the BCM was replaced you ll need to do the following IMPORTANT You MUST perform the following steps according to the applicable service manual to ensure the new BCM is properly programmed to the original vehicle settings BCM Write Configuration using CONSULT II Refer to WRITE CONFIGURATION PROCEDURE in section BCS of the applicable service manual Initialization of NATS System and Registration of all NATS Ignition Key I D s Refer to Nissan Technical Bulletin NTBO3 031b I D Registration Procedure of the Low Tire Pressure Warning System Refer to I D REGISTRATION PROCEDURE in section WT of the applicable service manual Register I D Code for
6. NISSAN NORTH AMERICA INC Technical Bulletin Sane SERVICE CAMPAIGN BULLETIN Reference Date NTBO5 086 September 22 2005 VOLUNTARY SERVICE CAMPAIGN BODY CONTROL MODULE SUB HARNESS CAMPAIGN I D P5234 APPLIED VEHICLES 2004 05 Titan A60 2004 05 Armada TA60 2005 Frontier D40 2005 Pathfinder R51 2005 Xterra N50 APPLIED VINS Titan King Cab 1N6 A06 4N50001 4 59347 1 Titan King Cab 1N6 A06 5N500006 547508 Titan Crew Cab 1N6 A07 4N055132 593472 Titan Crew Cab 1N6 A07 5N500000 547507 Armada 5N1 A08 4N057073 747082 Armada 5N1 A08 5N700000 725222 Frontier King Cab 1N6 D06 5C400026 437197 Frontier Crew Cab 1N6 D07 5C 40001 2 437203 Pathfinder 5N1 R18 5C700001 748937 Xterra 5N1 NO08 5C600000 621507 NOTE Use Service Comm to confirm campaign eligibility INTRODUCTION Nissan is committed to providing the highest levels of product quality and customer satisfaction We know that towing a trailer may have been an important consideration in the customer s purchase decision In new Titan Armada Frontier Pathfinder and Xterra vehicles Nissan recently introduced enhanced electronic circuitry which may help further protect a vehicle from damage or fire caused by a short circuit in the electrical system of a towed trailer due to problems with the trailer s wiring or mis installation of trailer lighting or electrical accessories Nissan is making this production enhancement available to owners of previ
7. RMINAL CHECK Check the condition of the BCM by performing a terminal check at the Trailer Lights Wiring Connector near the trailer hitch as follows Procedure A Terminal Check is split up into two sections e Section 1 For vehicles with a 4 terminal Trailer Lights Wiring Connector e Section 2 For vehicles with a 7 terminal Trailer Lights Wiring Connector NOTE For vehicles without a trailer lights wiring connector the BCM condition will be checked later in Procedure B Section 1 Vehicles Equipped With 4 terminal Trailer Lights Wiring Connector 1 Turn the ignition switch to the ON position 2 Make sure the combination switch and hazard switch are OFF 3 Using a Test Light check for power at terminals 3 and 4 see Figure 1 e If there is power at either terminal replace the BCM Return to the Repair Flow Chart for further instructions e If there is NO power at either terminal the circuit is OK Return to the Repair Flow Chart for further instructions a Test Light Comes ON Wi Lights Wiring Connector When Touching 3 or 4 4 Terminal Trailer NE a iin Trailer Hitch 12 3 4 Test Light Does Not Come ON When Touching 3 or 4 TP050650a Figure 1 4 Turn the ignition switch OFF 3 16 Section 2 Vehicles Equipped With 7 terminal Trailer Lights Wiring Connector 1 Turn the ignition switch to the ON position 2 Make sure the combination switch and hazard switch are OF
8. Remote Keyless Entry Keyfobs Refer to section BL of the applicable service manual BCM Headlamp Configuration Refer to HEADLAMP information in section LT of the applicable service manual 9 16 Section 2 Pathfinder Frontier Xterra Procedure 1 If you determined the BCM needs to be replaced from Procedure A Terminal Check e First perform BCM Read Configuration using CONSULT II e Todo this refer to READ CONFIGURATION PROCEDURE in section BCS in the applicable service manual 2 Record all radio station presets and then disconnect the negative battery cable CAUTION The complete repair needs to be conducted within one hour of disconnection of the battery If the battery is left disconnected for longer than one hour the idle setting may be lost and the vehicle may have difficulty starting FM1 FM2 AM 3 Remove the Driver s Front Kick Plate see Figure 10 e Carefully lift upward to release the securing clips Driver s Front Kick Plate Remove 4 Carefully reposition the Driver s Door Rubber Welt away from the Instrument Panel Side Trim see Figure 11 Driver s Door Rubber Welt TP050640 Figure 11 10 16 5 Carefully remove the Front Pillar Lower Finisher by pulling it rearward to release the Securing Clips see Figure 12 TPO50641 Figure 12 6 Remove two Screws and remove the Driver s Side Instrument
9. ay be lost and the vehicle may have difficulty starting AM FM1 FM2 3 Remove the Driver s Side Instrument Panel Lower Cover see Figure 3 e Remove two Screws at the lower corners of the Lower Cover e Carefully pull the cover rearward to release the securing clips e Disconnect all wire harness connectors from the panel Driver s Side Instrument Panel Lower Cover Remove TPO50651 Figure 3 5 16 4 Remove four Bolts and remove the Driver s Side Lower Knee Protector see Figure 4 Driver s Side Lower Knee Protector Remove Bolts Remove Figure 4 5 Remove the LH Instrument Lower Cover next to the Accelerator Pedal see Figure 5 e Carefully pull outward to release the Securing Clips LH Instrument Lower Cover Remove TP050653 Figure 5 6 16 6 If the BCM needs to be replaced as confirmed by Procedure A Terminal Check go ahead and replace the BCM now Then continue with step 8 below e Remove all three Harness Connectors from the BCM see Figure 6 e Remove the two BCM Mounting Bolts and remove BCM see Figure 6 e Install new BCM e Reconnect the top connector ONLY as viewed in Figure 6 7 If the BCM does not need to be replaced e Install the new Sub Harness e Start by disconnecting ONLY the two vertical Connectors at the BCM see Figure 6 wv g A BCM Mounting Bolt 2 BCM Harness Connector 7 Disconnect
10. eard when the brake lights come on e f you feel hear a clicking noise when performing steps c d and e go to the next step e f you do not feel hear a clicking noise when performing steps c d and e replace the BCM then go to the next step 15 Re install all components in reverse order of removal 16 Re program all radio station presets 17 If the BCM was replaced you ll need to do the following IMPORTANT You MUST perform the following steps according to the applicable service manual to ensure the new BCM is properly programmed to the original vehicle settings e BCM Write Configuration using CONSULT II Refer to WRITE CONFIGURATION PROCEDURE in section BCS of the applicable service manual e Initialization of NATS System and Registration of all NATS Ignition Key D s Refer to Nissan Technical Bulletin NTBO3 031b e 1 D Registration Procedure of the Low Tire Pressure Warning System Refer to I D REGISTRATION PROCEDURE in section WT of the applicable service manual e Register I D Code for Remote Keyless Entry Keyfobs Refer to section BL of the applicable service manual e BCM Headlamp Configuration Refer to HEADLAMP information in section LT of the applicable service manual 14 16 PARTS INFORMATION DESCRIPTION PART NUMBER QUANTITY BCM Sub Harness Titan Armada 24167 ZHOOA BCM Sub Harness Pathfinder Frontier Xterra 24167 ZH02A
11. f this offer please contact your Nissan dealer at your earliest convenience to arrange an appointment to have this new circuit installed on your vehicle at no cost to you This service should take about two hours to complete but you should plan to leave your vehicle at the dealership for a full day Please bring this notice with you when you keep your service appointment Important When towing always be sure to use a good quality trailer and other towing equipment Always check your trailer for proper operation of lights and electrical accessories after connecting it to your vehicle Thank you for choosing Nissan Nissan Division Nissan North America Inc 16 16
12. ously purchased vehicles so that they will have the same protection should they ever tow a trailer with a defective electrical system IDENTIFICATION NUMBER Nissan has assigned identification number P5234 to this campaign This number must appear on all communications and documentation of any nature dealing with this campaign NUMBER OF VEHICLES IN THIS CAMPAIGN The number of vehicles in this campaign is 304 000 DEALER RESPONSIBILITY It is the Nissan dealer s responsibility to check Service Comm for the campaign status on each vehicle falling within the range of this Voluntary Service Campaign P5234 that enters the service department This includes vehicles purchased from private parties or presented by transient tourist owners and vehicles in a Nissan dealer s inventory 1 16 REPAIR FLOW CHART Confirm the vehicle you are working on is part of this campaign Does the vehicle have a Trailer Lights Wiring Connector at the Trailer Hitch location Refer to Figures 1 and 2 in this bulletin Perform Terminal Check on Trailer Lights Wiring Connector See Procedure A Terminal Check OK Replace Body Control Module BCM See Procedure B You ll need all ignition keys from the customer to perform NATS registration Also you ll need all Remote Keyless Entry Keyfobs so you can re register them to the vehicle Install BCM Sub Harness See Procedure B END 2 16 PROCEDURE A TRAILER LIGHTS WIRING CONNECTOR TE
13. y i Y 4 me x A KNIT We y y es a AN 3 fps Ziel Steering q S ae AZ Shaft Coupling TP050645 Figure 16 11 At the other end of the BCM Sub Harness Connect the White Connector to the vehicle side harness white connector see Figure 17a Then connect the Black Connector to the vehicle side harness black connector see Figure 17b e Make sure the connectors are securely connected snapped in place BCM Sub Harness BCM Sub Harness White Connector BCM Sub Harness Vehicle Side BCM Black Connector BCM Vehicle Side BCM Sub Harness White Connector Black Connector TP050647 TP050646 Figure 17a Figure 17b 13 16 12 Secure the new BCM Sub Harness by snapping the Attachment Clip into the Instrument Panel Bracket Hole see Figure 18 Instrument Panel Bracket Hole BCM Sub Harness Attachement Clip TP050648 Figure 18 13 Re connect the negative battery cable 14 For vehicles without a trailer lights wiring connector confirm BCM operation as follows a Turn the ignition switch ON b Place your hand on the new BCM Sub Harness c Activate the left turn indicator blinker and confirm a click is felt heard each time the left turn indicator light flashes d Activate the right turn indicator blinker and confirm a click is felt heard each time the right turn indicator light flashes e Apply the brake pedal and confirm a click is felt h
Download Pdf Manuals
Related Search