Repeaters/Consoles Catalog
Contents
1. 380 512 MHz X182BZ provides the option of using the same antenna for receive and transmit in the UHF standalone base radio configuration If the X182BZ is ordered X265AP ADD NARROW PRESELECTOR 380 512 MHz is required The transmit frequencies must fall within one of the following subbands 380 403 403 435 435 470 470 494 and 494 512 MHz Also above 470 MHz the Tx and Rx frequency separation should be at least 3 0 MHz for best performance Below 470 MHz the Tx and Rx frequency separation should be at least 5 0 MHz for best performance X182CC ADD DUPLEXER 136 146 MHZ X182CC provides the option of using the same antenna for receive and transmit in the VHF 136 146 MHz standalone base radio configuration If the X182CC is ordered the X265AN ADD NARROW PRESELECTOR 136 154 is required The Tx and Rx frequency separation must be at least 1 5 MHz for best performance X182CB ADD DUPLEXER 144 160 MHZ X182CB provides the option of using the same antenna for receive and transmit in the VHF 144 160 MHz standalone base radio configuration If the X182CB is ordered the X265AN ADD NARROW PRESELECTOR 136 154 or X265AM ADD NARROW PRESELECTOR 150 174 are required The Tx and Rx frequency separation must be at least 1 5 MHz for best performance X182CA ADD DUPLEXER 158 174 MHZ X182CA provides the option of using the same antenna for receive and transmit in the VHF 158 174 MHz standalone base radio configuration If the X182C2. 99 00 RMN5068 Desk Microphone Black 120 00 HKKN4000 Power Sense Cable in the event of a power loss this cable will allow the repeater to power up automatically once A C is restored 25 00 HLN9457 Hardware Kit for use with the Expanded Accessory Connector includes 16 connector pins five 5 8 wires with pins attached and 6 95 an extra housing 6864110R66 CDR700 amp CDR500 Service Manual 15 00 Preselectors To order these Preselectors TUNED call Dealer Support Services to place your order at 800 927 2744 Prompt 1 1 To order these Preselectors UN TUNED order directly through RPSD The CDR700 allows for the internal installation of either a duplexer or a preselector The CDR500 allows for internal mounting of a duplexer and a preselector All preselectors have female type N connector A dealer supplied type N male to male connector is required for proper operation The length of the cable depends on your application Call Motorola RPSD Parts ID at 800 422 4210 to find a cable for your individual application or for additional preselector options HFD8461 VHF Preselector 144 160 MHz 336 00 HFD8462 VHF Preselector 160 174 MHz 336 00 HFE8459 UHF Preselector 440 474 MHz 450 00 Lightning Protection Recommendation Accessories Phone Remote Line Suppressors RRX4021 Single Line Suppressor 50 00 Coaxial Cable In Line Arrestors DSISBSOLNC2 Coax Protector Available to order via MOL only 66 00
3. VHF amp UHF VXR 7000 Desktop Repeater Features 12 5 25 kHz Switchable Channel Spacing 16 Channels Output Power 10 50 Watts Adjustable Programmable Busy Channel Lock Out Programmable Busy Timer Lock Out CWID CTCSS DCS Codes Automatic DC Power Supply Back Up 100 Continuous Duty Cycle The available channel stepping frequency ranges for the VXR 7000 are 2 5kHz 5kHz 6 25kHz 10kHz and 12 5kHz Repeater Package Items Untuned duplexers for the VXR 7000 are available The duplexers must be order separately The desktop microphone must be ordered separately Repeater CPS is downloadable from MOL Warranty Policy Repeater warranty is 3 Years For warranty repair repeater must be sent to Vertex Standard directly Please contact Vertex Standard at 1 800 2Vertex Vertex Accessory warranty is 1 year For warranty please contact Motorola Customer Service at 1 800 927 2744 for a warranty replacement order Service Repair Policy VXR 7000 repeaters are supported by Motorola s 45 Day DOA Policy For 45 day DOA radios please contact Motorola s Customer Service at 1 800 927 2744 After 45 days please contact Vertex Standard directly for all repair services at 1 800 2Vertex for the required repair request form All service charges will require credit card payment Return Policy These products are supported by the Motorola Return Policy All product must be returned with factory box packing materials owner
4. VHF or UHF models can be utilized Select Repeater Controller s HLN3948 Basic Interface Repeater Controller Provides repeater functionality remote knock down set up in crossband and uni bi 288 00 directional capabilities B version includes a mounting shroud which is required for proper installation within the CDR700 repeater housing HLN9119 ZR340 Advanced Interconnect Controller Provides advanced interconnect capabilities including password driven access and 803 25 disconnect codes customized toll restrict and toll restrict bypass Does not use RSS Programming done via DTMF parameters For technical training of Motorola products please visit https learning motorolasolutions com U S Professional Price Pages Conventional Fixed Page 2 CDR700 amp CDR500 Date 6 5 15 REPEATER HOUSINGS SUGGESTED RETAIL ACCESSORIES MODEL NUMBER DESCRIPTION MSRP Duplexer Accessories All duplexers have female type N connectors Select One 1 Tuned Duplexer 5 Days ARO Specify frequency for tuning HFD8465 VHF Duplexer 150 160 MHz requires Internal Duplexer amp Antenna Cable Kit minimum amp maximum freq separation is 4 5 MHz 6 MHz 611 00 Note To order this Duplexer TUNED call Dealer Support Services to place your order at 800 927 2744 Prompt 1 1 OR Select One 1 Untuned Duplexer Requires tuning in the field VHF Duplexers HFD8188 VHF Duplexer 144 155 MHz minimum amp maximum freq separa
5. X530BG ADD VHF 136 174 MHZ X448AA ADD UHF R1 380 435 MHZ 150W High Power 800MHz PA CA02478AA ADD 800MHZ 150W HI POWER Base Radio Software CA01949AA ADD ANALOG CONVENTIONAL SOFTWARE Energy Efficiency CA01953AA ADD POWER EFFICIENCY PACKAGE Conventional Software System Configuration CA01952AA ADD ANALOG CONVENTIONAL SIMULCAST SOFTWARE CA01951AA ADD ANALOG CONVENTIONAL VOTING SOFTWARE Conventional Features CA01504AA ADD ANTENNA RELAY CA01503AA ADD FALL BACK IN SIMULCAST CABINET REPEAT CA01947AA ADD RECEIVER SCAN OPERATION CA01950AA ADD CONVENTIONAL MULTI NAC MULTI PL CA01954AA ADD WILDCARD W GPIO CA01955AA ADD MAIN STANDBY OPERATION Peripherals X182BW ADD DUPLEXER 700 MHZ X182BX ADD DUPLEXER 800 MHZ X182BZ ADD DUPLEXER UHF X182CC ADD DUPLEXER 136 146 MHZ THEN TX AND RX MUST BE 136 146 X182CB ADD DUPLEXER 144 160 MHZ THEN TX AND RX MUST BE 144 160 X182CA ADD DUPLEXER 158 174 MHZ CA00882AA ADD 700 MHZ TX FILTER W PMU CA00883AA ADD 800 MHZ TX FILTER W PMU X265AJ ADD BASE RADIO PRESELECTOR 700 MHZ X265AH ADD BR PRESELECTOR 800 MHZ 6 300 00 6 300 00 6 300 00 6 300 00 12 500 00 N C 500 00 N C N C 350 00 600 00 400 00 500 00 1 200 00 450 00 1 380 00 1 380 00 1 380 00 1 380 00 1 380 00 1 380 00 1 000 00 1 000 00 500 00 500 00 U S Professional Price Pages Conventional Fixed Page 9 GTR 8000 Date 1 5 15 GTR 8000 AN
6. be used Order 2 Network Terminator s CDN6115 for every HIB DDN1388 ordered in Step 1 Order appropriate cabling for modules For each GPIO and CIB module ordered in Step 3 order e 1 PUNCH BLOCK DUAL 25 PAIR CDN6118 e 1 CABLE ASSY 25 PR M NONE 25FT CDN6135 And 1 of the cables below e CBL ASSY 25 PR MALE MALE 10 FT CDN6129 OR e CBL ASSY 25 PR MALE MALE 25 FT CDN6130 For each AIB module ordered in Step 3 order CBL ASSY AIB COMPARATOR 10 FT CDN6131 Order 1 CABLE KIT HIB PC AT XT 6 FT DDN6132 for every system U S Professional Price Pages Trunking Fixed Page 10 Date 1 5 15 MONITORING amp CONTROL NETWORK MCN FOR MIP 5000 CONSOLE SUGGESTED RETAIL Ordering Requirements Continued It s recommended to order the appropriate manual for modules ordered in Step 1 and Step 3 manuals are not included with Modules Manuals for Modules in Step 1 Both manuals are needed for DDN1388 e HIB HARDWARE GUIDE CDN6110 e MCN SERVER SOFTWARE MANUAL DDN1402 Manuals for Modules in Step 3 e GPIO HARDWARE GUIDE DDN1386 e AIB HARDWARE GUIDE CDN6107 e CIB HARDWARE GUIDE CDN6109 STEP 9 Optional Order the appropriate quantity of rackmount shelves for modules ordered in Step 1 and Step 3 e DDN1387 is available to rackmount the MCN RCD HIB MODULE Each rackmount will support 1 DDN1388 Step 1 and two additional GPIO AIB or CIB modules Step 3 e Additional rackmount shelves for the GPIO AIB or CIB modules ordered i
7. is attached to the back side of the base radio When ordering this option the frequency separation between the highest Rx frequency and the lowest Rx frequency can be no more than 4 MHz X265AM ADD BASE RADIO PRESELECTOR 150 174 MHZ X265AM provides RX filtering in the VHF subband 150 174 MHz for the standalone base radio configuration and is attached to the back side of the base radio When ordering this option the frequency separation between the highest Rx frequency and the lowest Rx frequency can be no more than 4 MHz X265AP ADD BASE RADIO PRESELECTOR 380 512 MHZ X265AP provides RX filtering in the UHF subband 380 512 MHz for the standalone base radio configuration and is attached to the back side of the base radio When ordering this option the frequency separation between the highest Rx frequency and the lowest Rx frequency can be no more than 4 MHz 7 3 Dual Circulator If an external dual circulator is needed order quantity one of X676BF X676BG X676BJ X676BI or X676BH based on the frequency of the system NOTE The dual circulator is not compatible when the base radio ordered is using Linear Simulcast Modulation LSM in the UHF X640AL or X448AA or the VHF frequency band X530BG X676BF ADD 700 800 MHZ EXTERNAL DUAL CIRCULATOR X676BF adds 2 circulators and a low pass filter that are mounted on a 2 rack unit tray for the 700 800 MHz band Since the power amplifier has one circulator this o
8. s manual amp warranty cards Contact Motorola Customer Service at 1 800 927 2744 for return Post Sales Support For post sales technical inquiries and support needs please contact Vertex Standard directly at 1 800 2Vertex MODEL DESCRIPTION MSRP Options TO COMPLETE AN ORDER YOU MUST MAKE ONE 1 CHOICE FOR STEP 1 Select One 1 of the following Desktop Repeater Models A13670010 VXR 7000VC PKG 1 SOW 150 174 Mhz 16 Ch 1 650 00 A13680014 VXR 7000UD PKG 1 SOW 450 480 Mhz 16 Ch 1 650 00 Select microphone option AAF13X001 MD 12A8J Mobile Desktop Microphone 102 00 Optional All duplexers have female type N connectors Select One 1 Untuned Duplexer XUFIP0002 Untuned VHF Duplexer for VXR 7000 148 160 MHz 410 00 XUFIPO001 Untuned UHF Duplexer for VXR 7000 440 480 MHz 410 00 Optional Required See Below Select cable option if duplexer was ordered above AAA21X001 CT 68 Duplexer Installation Cable Kit 63 00 MODEL DESCRIPTION MSRP AAF13X001 MD 12A8J Mobile Desktop Microphone 102 00 AAA21X001 CT 68 Duplexer Installation Cable Kit 63 00 XUFIP0002 Untuned VHF Duplexer for VXR 7000 148 160 MHz 410 00 XUFIPO001 Untuned UHF Duplexer for VXR 7000 440 480 MHz 410 00 A06420002 VPL 1 Programming Cable 87 00 U S Professional Price Pages Trunking Fixed Page 2 MC1000 MC2000 amp MC2500 Date 1 5 15 DESKTOP CONTROLLERS SUGGESTED RETAIL Models All MC1000 MC2000 and MC2500 Models Include 4 Frequency
9. with L3217 50 00 Field Install Kits DDN6481 Punch Block with Spark Gap recommended 405 00 DDN6516 Headset Jackbox adds headset capacity See MC3000 pages for compatible headsets 110 00 DDN6668 Single Footswitch 94 00 DDN6341 110VAC Transformer for MC1000 models 69 00 DDN6342 110 220VAC 50 60 Hz Power Supply for MC2000 and MC3000 models 219 00 DDN6339 110 220VAC 50 60 Hz Power Supply for MC2500 models 198 00 DDN7066 110 220VAC 50 60 Hz Power Supply for L3276 amp L3277 Remote Adapters 195 00 Programming MC2000 and MC2500 Models Only RVN4178 Radio Service Software includes CD ROM 265 00 DDN6367 Radio Service Software Cable AT DB9 35 00 U S Professional Price Pages Trunking Fixed Page 4 MIP 5000 VoIP RADIO CONSOLE Date 1 5 15 SUGGESTED RETAIL MIP 5000 Release 4 2 Now Shipping MIP 500 Release 4 2 New Features e Support for XPR 5550 MOTOTRBO Mobile e 48 Channel Support 2m e Microsoft Windows 8 1 64 Bit e Multi Touch Monitor Support e Dual Channel IRR Support g a A MIP 5000 Console General Information The MIP 5000 VoIP Radio console is designed to provide customers an affordable solution to transmit dispatch quality voice over their existing Multicast enabled Ethernet network The MIP 5000 radio console connects up to 100 users with flexible licensing that is available with 1 4 8 12 24 and 48 channel software options In addition up to 128 radio resources can be connected to
10. 00 Tuner Repeater Diagnostic Control and the MOTOTRBO System Planner 3 Year Subscription Package Software is compatible with Windows XP amp Windows Vista Home and Professional versions and Windows 7 support for Windows 2000 ended 6 30 09 Note Software requires a license agreement and is not intended for resale DDN9957 HI SPEED USB CABLE 6FT TYPE A B 20 00 Power Cable CA01520AA ADD POWER CABLE DC 25 00 Misc X269AC ENH SPECTRA TAC 150 00 X699BA ADD MTR3000 FACTORY TEST REPORT N C Peripherals X265UL ADD PRESELECTOR UHF 380 435 MHZ 500 00 X265UM ADD PRESELECTOR UHF 435 470 MHZ 500 00 X265UH ADD PRESELECTOR UHF 470 524 MHZ 500 00 X265VL ADD PRESELECTOR VHF 136 154 MHZ 500 00 X265VH ADD PRESELECTOR VHF 150 174MHZ 500 00 Kits amp Accessories MTR3000 Field Replaceable Units FRUs All Field Replacement Units FRUs are available through Customer Care and Service Division RPSD 1 800 927 2744 FRU MTR3000 Satellite Receivers DLN6776 FRU MTR3000 RECEIVER EXCITER FRU 100 00 DLN6777 FRU MTR3000 RECEIVER PA FRU 100 00 SPEAKERS TEST CABLE HSN1006 EXTERNAL SPEAKER 104 00 0185180U01 CABLE FOR EXTERNAL SPEAKER 18 25 30009493001 RECEIVER AUDIO TEST CABLE 65 25 For technical training of Motorola products please visit https learning motorolasolutions com U S Professional Price Pages Trunking Fixed Page 1 VXR 7000 DESKTOP REPEATER Date 1 5 15 VERTEX STANDARD SUGGESTED RETAIL
11. 5 Expansion software from 4 channel to 48 channel capability 23 000 00 112746 Expansion software from 8 channel to 48 channel capability 19 000 00 112747 Expansion software from 12 channel to 48 channel capability 15 000 00 T2748 Expansion software from 24 channel to 48 channel capability 10 000 00 Note Orders place for Expansion Software must be accompanied by telephone call to System Support Center SSC to open an entitlement case Before your MIP 5000 Expansion Software order can ship you must call Support Center at 800 221 7144 option 4on the call tree and request a software case be opened Be prepared to provide the Factory Order FO and the Serial number of currently installed software as well as the new FO for Expansion SW Demo Equipment L3544 MIP5000 4 Ch Demo Software 750 00 The 4 channel MIP 5000 Demo Software provides software to dealers at a significant discount This discount is made available to dealers who want to set up a working MIP 5000 system for Customer demo purposes The offer is limited by the number of dealership offices To complete the demo system the following components need to be ordered 1 Up to 4 MIP 5000 Gateways L3482 local L3483 tone L3484 digital L3598 MOTOTRBO 2 DDN8671 Null Modem cable for programming the gateway 3 DDN9492 USB Headset Jackbox 4 B1914 Desktop Gooseneck Microphone 5 Mobile radio with radio interface cables to connect the gateway to the radio 6 7 a set of PC Spea
12. 7 4 Optional Conventional Hardware Kits The following kits provide add on hardware including associated cables and fasteners with installation instructions for specialized Conventional base radio solutions CA01958AA ADD T2 2R RECEIVER MUTE CA01959AA ADD T3 3R RECEIVER MUTE CA01960AA ADD T4 4R RECEIVER MUTE CA01961AA ADD RCVR SOFT NO SPLITTER CA01957AA ADD T1 2R W TALKAROUND CA01962AA ADD T2 2R DUPLEXER amp TRPL RELAY 8 Cables CA01400AA ADD POWER CABLE DC A 12 foot AC power cable will come standard with the base radio If a DC power cable is required order option CAO1400AA and a DC cable will be shipped in addition to the AC cable A Battery Temperature Sensor and a 40 foot long cable are included when CAO1400AA option is ordered CA00975AA ADD BATTERY TEMPERATURE SENSOR EXTENSION CABLE The CA00975AA option offers an extension cable that provides a 50 foot extension Up to 3 extensions can be ordered 9 Rack Mount Hardware Choose rack mount hardware if required X153AW ADD RACK MOUNT HARDWARE X153AW provides rack mount hardware for the base radio as well as any associated optional peripheral equipment It should be selected if the base radio will be installed in standard 19 inch relay racks or if it is being installed into an existing Quantar rack Model Number Description MSRP T7039 GTR 8000 BASE RADIO 6 000 00 Frequency Band CA00855AA ADD 700 800 MHZ X640AL ADD UHF R2 435 524 MHZ
13. 9 99375 MHz If Freq TX is 764 00625 775 99375 MHz then Freq Rx TX 30 If Freq TX is 851 00625 869 99375 MHz then Freq Rx TX 45 All frequencies must be divisible by 2 5 or 3 125 kHz Note Currently 796 09375 806 88125 808 31875 and 822 375 are not supported for Rx UHF R2 Frequency Rules for X640AL RX Range 435 0000 524 0000 MHz TX Range 435 0000 524 0000 MHz If Freq TX is 435 524 MHz then Freq Rx gt 25 MHz TX All frequencies must be divisible by 2 5 or 3 125 kHz Note Currently 454 500 474 6375 494 05625 and 511 3125 are not supported for Rx UHF R1 Frequency Rules for X448AA RX Range 380 0000 435 0000 MHz TX Range 380 0000 435 0000 MHz If Freq TX is 380 435 MHz then Freq Rx gt 25 MHz TX All frequencies must be divisible by 2 5 or 3 125 kHz Note Currently 380 250 and 416 925 MHz are not supported for Rx U S Professional Price Pages Conventional Fixed Page 6 GTR 8000 Date 1 5 15 GTR 8000 ANALOG CONVENTIONAL BASE RADIO SUGGESTED RETAIL GENERAL INFORMATION VHF Frequency Rules for X530BG RX Range 136 0000 174 0000 MHz TX Range 136 0000 174 0000 MHz If Freq TX is 136 174 MHz then Freq Rx gt 25 MHz TX All frequencies must be divisible by 2 5 or 3 125 kHz 150W High Power 800MHz PA CA02478AA ADD 800MHZ 150W HI POWER CA02478AA provides high power transmission in the 800MHz frequency It s compati
14. A is ordered the X265AM ADD NARROW PRESELECTOR 150 174 is required The Tx and Rx frequency separation must be at least 1 5 MHz for best performance CA00882AA ADD 700 MHz TX FILTER w PMU CA00882AA provides the TX filtering of up to 12 combined 700 MHz transmitters The Tx filter can be added after the cavity combiner CA00883AA ADD 800 MHz TX FILTER w PMU CA00883AA provides the required TX filtering of up to 12 combined 800 MHz transmitters The Tx filter can be added after the cavity combiner 7 2 Narrow Preselector The Base Radio Preselector rejects unwanted signals including the transmitter signals from overloading the receiver If TIA102 CAAB Class A spurious response rejection 90 dB specification is required the Base Radio Preselector must be ordered The Narrow Preselector is optional If a Duplexer is to be ordered also a Narrow Preselector is required for UHF X448AA or X640AL or VHF X530BG systems X265AJ ADD BASE RADIO PRESELECTOR 700 MHz X265AJ provides RX filtering in the 700 MHz standalone base radio configuration and is attached to the back side of the base radio X265AH ADD BASE RADIO PRESELECTOR 800 MHz X265AH provides RX filtering in the 800 MHz standalone base radio configuration and is attached to the back side of the base radio X265AN ADD BASE RADIO PRESELECTOR 136 154 MHZ X265AN provides RX filtering in the VHF subband 136 154 MHz for the standalone base radio configuration and
15. ALOG CONVENTIONAL BASE RADIO SUGGESTED RETAIL GENERAL INFORMATION Model Number Description MSRP Peripherals continued X265AN ADD NARROW PRESELCTOR 136 154 MHZ 500 00 X265AM BR PRESELCTOR 150 174 MHZ 500 00 X265AP ADD BR PRESELECTOR 380 512 MHZ 500 00 X676BF ADD 700 800 MHZ EXTERNAL DUAL CIRCULATOR 1 000 00 X676BG UHF EXTERNAL DUAL CIRCULATOR 435 494 MHZ 1 500 00 X676BJ ADD EXT DUAL CIRCULATOR 136 146 MHZ 1 500 00 X676BI ADD EXT DUAL CIRCULATOR 144 160 MHZ 1 500 00 X676BH ADD EXT DUAL CIRCULATOR 158 174 MHZ 1 500 00 Conventional Hardware CA01958AA T2 2R RECEIVER MUTE 2 000 00 CA01959AA T3 3R RECEIVE MUTE 2 000 00 CA01960AA T4 4R RECEIVER MUTE 2 000 00 CA01961AA RCVR SOFT NO SPLITTER 400 00 CA01957AA T1 2R W TALKAROUND 1 200 00 CA01962AA T2 2R DUPLXR amp TRPL RELAY 4 000 00 Cables CA01400AA ADD POWER CABLE DC N C Rack Mount Hardware X153AW ADD RACK MOUNT HARDWARE 50 00 Nomenclature Description MSRP DLN6895 FRU PA 7 800 MHz 1 200 00 DLN6896 FRU PA UHF R2 2 221 00 DLN6891 FRU PA UHF R1 1 200 00 DLN6897 FRU PA VHF 2 416 00 DLN6935A FRU 150W PA 800MHZ 12 500 00 DLN6883 FRU XCVR 7 800 MHZ V2 W OPT CARD 4 000 00 DLN6886 FRU XCVR UHF R2 V2 W OPTION CARD 4 000 00 DLN6887 FRU XCVR UHF R2 V2 PWR EFF OPT CRD 4 000 00 DLN6889 FRU XCVR UHF R1 V2 W OPTION CARD 4 000 00 DLN6890 FRU XCVR UHF R1 V2 PWR EFF OPT CRD 4 000 00 DLN6893 FRU XCVR VHF V2 W OPTION CARD 4 000 00 DLN6781 FRU P
16. DDN8671 15 Ft Null Modem Cable DB9 F F 13 00 1 cable required per system to configure the gateway DDN8672AC Spare Power Supply for MIP 5000 Gateway w Power Cable California Compliant 146 00 MIP 5000 Software Channels L3485 MIP5000 VoIP Dispatch SW 1 Ch Provides the software application and licenses for one MIP 5000 1 Ch Dispatch 1 500 00 console Allows a dispatcher to access and control one MIP 5000 Local Tone Digital or MOTOTRBO Gateway The PC microphone speakers and headset are not included and must be provided separately L3486 MIP5000 VoIP Dispatch SW 4 Ch Provides the software application and licenses for one MIP 5000 4 Ch Dispatch 2 500 00 console Allows a dispatcher to access and control up to four MIP 5000 Local Tone Digital or MOTOTRBO Gateways The PC microphone speakers and headset are not included and must be provided separately L3487 MIP5000 VoIP Dispatch SW 8 Ch Provides the software application and licenses for one MIP 5000 8 Ch Dispatch 6 500 00 console Allows a dispatcher to access and control up to eight MIP 5000 Local Tone Digital or MOTOTRBO Gateways The PC microphone speakers and headset are not included and must be provided separately L3499 MIP5000 VoIP Dispatch SW 12 Ch Provides the software application and license for one MIP 5000 12 Ch Dispatch 10 500 00 console Allows a dispatcher to access and control up to 12 MIP 5000 Local Tone Digital or MOTOTRBO Gateways The PC microphon
17. OWER SUPPLY 2 200 00 DLN6793 FRU PWR EFF POWER SUPPLY AC 48VDC 1 425 00 DLN6795 FRU T2 2R RECEIVER MUTE 2 000 00 DLN6796 FRU T3 3R RECEIVE MUTE 2 000 00 DLN6797 FRU T4 4R RECEIVER MUTE 2 000 00 DLN6798 FRU RCVR SOFT NO SPLITTER 400 00 DLN6799 FRU T1 2R W TALKAROUND 1 200 00 DLN6800 FRU T2 2R DUPLXR amp TRPL RELAY 4 000 00 DLN6821 FRU GTR ANALOG 4W E amp M SIMULCST KIT 250 00 DLN6898 FRU FAN MODULE 206 00 DLN6455 CONFIGURATION SERVICE SOFTWARE 25 00 DLN6836 FRU GTR 136 146MHz EXT DUAL CIRCULATOR KIT 1 500 00 DLN6837 FRU GTR 144 160MHz EXT DUAL CIRCULATOR KIT 1 500 00 DLN6838 FRU GTR 158 174MHz EXT DUAL CIRCULATOR KIT 1 500 00 DLN6839 FRU GTR 380 403MHz EXT DUAL CIRCULATOR KIT 1 500 00 DLN6840 FRU GTR 403 470MHz EXT DUAL CIRCULATOR KIT 1 500 00 DLN6841 FRU GTR 470 512MHz EXT DUAL CIRCULATOR KIT 1 500 00 DLN6842 FRU GTR 764 870MHz EXT DUAL CIRCULATOR KIT 1 500 00 U S Professional Price Pages Conventional Fixed Page 10 MTR3000 SATELLITE RECEIVER Date 1 5 15 VHF amp UHF 800 900 MHz SUGGESTED RETAIL MODELS amp OPTIONS GENERAL INFORMATION MTR3000 Satellite Receiver operates in Analog Conventional operation only MTR3000 Satellite Receiver can also be used as Digital Voting Satellite Receiver RoHS Restriction of Hazardous Substances Compliant Come standard with a basic install service and user manual Come standard with a wireline board Switching power supply functions for over a
18. Professional Price Pages Trunking Fixed Page 6 MIP 5000 VoIP RADIO CONSOLE Date 1 5 15 Models amp Accessories SUGGESTED RETAIL Model Number Description MSRP L3482AC MIP5000 VoIP Local Gateway PS California Compliant Provides one MIP 5000 Local Gateway Each gateway is 798 00 capable of supporting one local control radio Punch blocks and cabling for connecting to the radio are not included in the L3482AC An Ethernet cable not included is also required for each L3482AC L3483AC MIP 5000 VoIP Tone Gateway PS California Compliant Provides one MIP 5000 Tone Gateway Each gateway is 798 00 capable of supporting one tone remote controlled base station Punch blocks and cabling for connecting to the station are not included in the L3483AC An Ethernet cable not included is also required for each L3483AC L3484AC MIP 5000 VoIP Digital Gateway PS California Compliant Provides one MIP 5000 Digital Gateway Each gateway is 798 00 capable of supporting one SB9600 capable radio Punch blocks and cabling for connecting to the radio are not included in the L3484AC An Ethernet cable not included is also required for each L3484AC L3598AC MIP5000 VoIP MOTOTRBO Gateway Provides one MIP 5000 MOTOTRBO Gateway Each gateway is capable of 798 00 supporting one XPR4550 or XPR 5550 radio Punch blocks and cabling for connecting to the radio are not included in the L3598AC An Ethernet cable not included is also required for each L3598AC
19. RRX4032 Tower Mounting Hardware for Lightning Arrestor 15 00 Desktop Controllers and Remote Adapters See Desktop Controllers and Remote Adapters for pricing and ordering information within this section U S Professional Price Pages Conventional Fixed Page 3 Date 1 5 15 REPEATER INTERFACE SUGGESTED RETAIL COMMUNICATIONS KIT The Repeater Interface Communications Kit Model Includes For use with CDM750 CDM1250 amp CDM1550 Selectable Hang Time PL DPL CSQ Uni Directional or Bi Directional Repeater Operation Singleband and Crossband Operation Transparent Operation Remote Repeater Set Up and Knock Down LED Indicators for Repeater Enable COR and Repeater Set Up Front Panel Control for Repeater Enable and Set Up Interface Box Mounting Bracket and all required Cables MODEL DESCRIPTION HLN3333 Repeater Interface Communications Kit includes manual General Accessories HKN9019 16 Pin Conductor Cable same as HKN9969 3 Ft long enhanced connectors 14 44 HKN9969_R Accessory for Repeater Interface Communications Kit additional 16 conductor cable 3 Ft long for connection to other accessories 35 50 6880901Z79 B R 1 C K Service amp Programming Manual most current issue includes MMR 062 5 67 MOTOROLA Repeater Interface REPEATER C ENABLE For technical training of Motorola products please visit https learning motorolasolutions com U S Professi
20. Station Control Push to Talk Handset 2o0r4 Wire LOTL LOBL Black Color Volume Control Transmit LED Monitor Switch 120V AC 60 Hz Power Supply The MC2000 is going EOL with a last order date of September 30 2014 MC2500 Supervisory Takeover or Line Select MC2000 MC1000 Operator Cross Mute MC2000 MC2500 Additional Features Intercom 18 Programmable Buttons LTR Compatible 2 Line x 20 Character Backlit Display Service Manual Multi Frequency Capability up to 16 frequencies on Tone One Year Warranty 110V 220V AC 50 60 Hz Power Supply MDC Features MC2500 Only Additional Features PTT Unit ID Encode Decode 4 Base Station Control Capable of controlling 4 Tone Voice Selective Call Encode Decode channels or 3 Tone channels and 1 DC channel Call Alert Short Call Alert Encode Decode Also capable of E amp M control on all channels Use Status Message Decode of a Tone or DC Remote Adapter is required when Radio Enable Disable Encode connected to a mobile in a tray Radio Check Encode Connector for Unselect Speaker Emergency Alarm Decode Individual Volume Control Recent User Stack Last nine records are stored for review at any time Dedicated Logging Recorder Output RS232 Port Allows RSS programming via computer or the logging of MDC1200 inbound Radio Patch outbound Serial Printer Port activity for permanent record keeping on a serial pri
21. TANDBY OPERATION CA01955AA provides WildCard programming presets and cabling for a side by side base radio main standby configuration 7 Peripherals 7 1 Tx Filters and Duplexers Tx Filters are not compatible with Duplexers In circuit or IP simulcast configurations the PMU on the TX filters are not functional 700 800 MHz If the customer frequencies are in the 700 MHz frequency range Tx 764 00625 775 99375 MHz the customer must order X182BW or CA00882AA per FCC licensing rules If the customer frequencies are in the 800 MHz frequency range Tx 851 00625 869 99375 MHz the following peripherals are optional UHF R1 380 435 MHz R2 435 524 MHz The following peripherals are optional VHF 136 174 MHz The following peripherals are optional TX and RX frequencies must be at least 1 5 MHz apart if peripherals are desired X182BW ADD DUPLEXER 700 MHZ X182BW provides the option of using the same antenna for receive and transmit in the 700 MHz standalone base radio configuration This option provides the filtering required by the FCC for 700 MHz X182BX ADD DUPLEXER 800 MHZ X182BX provides the option of using the same antenna for receive and transmit in the 800 MHz standalone base radio configuration U S Professional Price Pages Conventional Fixed Page 7 GTR 8000 Date 1 5 15 GTR 8000 ANALOG CONVENTIONAL BASE RADIO SUGGESTED RETAIL GENERAL INFORMATION 7 Peripherals continued X182BZ ADD DUPLEXER UHF
22. U S Professional Price Pages Conventional Fixed Page 1 Date 1 5 15 CDR700 amp CDR500 SUGGESTED RETAIL REPEATER HOUSINGS CDR Repeater Housings CDR700 Desktop Mount CDR500 Wall Mount Each CDR700 CDR500 Housing Includes Power Supply Fan Kit Repeater Interface Cables Service Manual 2 Year Warranty CDR700 Notes CDR500 1 Each repeater housing utlizes two 2 CDM Series mobiles 2 All CDM Series LowBand VHF amp UHF models are compatible 3 FCC Frequency Stability requirements for repeater applications have been met for UHF 450 512 MHz operating at 12 5 kHz channel spacing See the Mobile price pages for new CDM750 CDM1250 amp CDM1550 models MODEL NUMBER DESCRIPTION MSRP CDR500 700 Repeater Housing Select One 1 CDR Repeater Housing These housings are compatible only with CDM Series Mobiles NOTE HKKN4000 Power Sense Cable In the event of a power loss this cable will allow the repeater to power up automatically once A C is restored HKLN4056 CDR700 Desktop Repeater Housing 666 00 This housing contains one controller slot which accommodates 7 wide repeater controllers HKLN4060 CDR500 Wall Mount Repeater Housing 799 00 This housing contains one controller slot which accommodates 7 wide repeater controllers Purchase Separately Required Select Two 2 CDM Series Mobiles See CDM Series price pages for model availability and pricing Any two 2 CDM LowBand
23. ble with anolog simulcast amp non simulcast 3 Base Radio Software CA01949AA ADD ANALOG CONVENTIONAL SOFTWARE CA01949AA provides a circuit analog conventional base radio This base radio software supports 2wire 4wire and 8wire circuit analog wireline links 16 programmable channel personalities Each channel personality can be configured for base station repeater simplex or receive only operation TRC wireline keying is supported with a full complement of programmable function tones The CSS Configuration Service Software install disc is included with this option 4 Energy Efficiency Options CA01953AA ADD POWER EFFICIENCY PACKAGE This optional feature provides hardware and software for reduced power consumption to accommodate needs at sites without grid power or that are driven off alternative energy sources Only available with UHF R2 X640AL UHF R1 X448AA amp VHF X530BG 5 Conventional Software System Configuration Choose the appropriate optional conventional software system configuration if required CA01952AA ADD ANALOG CONVENTIONAL SIMULCAST SOFTWARE CA01952AA provides the analog conventional base radio with the Gen Tx Data and E amp M keying interface to a DSM channel bank card The base radio must be provided with a 5MHZ 1PPS composite reference to ensure the timing and signal integrity required for analog simulcast The GTR 8000 base radio cannot be mixed with QUANTAR analog simulcast stations on the sa
24. e speakers and headset are not included and must be provided separately 13567 MIP5000 VoIP Dispatch SW 24 Ch Provides the software application and USB Hasp Key for one MIP5000 24 15 500 00 Channel dispatch console Allows a dispatcher to access and control up to 24 MIP5000 Local Tone Digital or MOTOTRBO Gateways The PC microphone speakers and headset are not included and must be provided separately 13630 MIP5000 VoIP Dispatch SW 48 Ch Provides the software application and USB Hasp Key for one MIP5000 48 25 000 00 Channel dispatch console Allows a dispatcher to access and control up to 48 MIP5000 Local Tone Digital or MOTOTRBO Gateways The PC microphone speakers and headset are not included and must be provided separately MIP 5000 Options for Software 7705515 MIPSOOO Basic Model USB Headset Jackbox 500 00 TT05522 MIP5000 Enhanced Model USB Headset Jackbox 575 00 U S Professional Price Pages Trunking Fixed Page 7 MIP 5000 VoIP RADIO CONSOLE Date 1 5 15 Models amp Accessories SUGGESTED RETAIL Model Number Description MSRP 1712194 Expansion software from 12 channel to 24 channel capability 5 500 00 T2193 Expansion software from 8 channel to 24 channel capability 9 500 00 T2192 Expansion software from 4 channel to 12 channel capability 8 500 00 72191 Expansion software from 4 channel to 24 channel capability 13 000 00 712225 Expansion software from 8 channel to 12 channel capability 4 500 00 1274
25. e radio that offers high reliability future expandability and excellent coverage The GTR 8000 Base Radio deployed as an analog conventional repeater can be upgraded to simulcast digital trunking and other configurations including P25 TDMA with software upgrades only no hardware changes Its high performing analog capabilities enable narrow banding migrations that maximize audio performance With its compact design and superior hardware the GTR 8000 surpasses the bar previously set by QUANTAR GENERAL INFORMATION High Powered Performance 100 ppb frequency stability directly enhances analog audio performance Supports optional analog features including sumulcast repeater access setup knockdown scanning receiver multi PL and WildCard with GPIO General Purpose Inputs Outputs Optional preselector achieves 95dB spurious and image response rejection to block out transmitters at crowded sites Standard 48V battery revert and charging capability eliminates the need for an uninterruptible power supply UPS in many installations Installation amp serviceability Compact hardware utilizes a 3 rack unit chassis Ships factory aligned ready for installation Hot Swap hardware enables service and hardware replacement without system down time Software download can be managed while online and fully operational All servicing can be performed from the front of the station High reliability fans are rated for 10 years of contin
26. ion RO3 00 00 1 7 x N A RO3 00 01 1 7 x N A RO4 00 00 1 8 x N A RO4 01 00 1 9 x N A RO4 01 01 1 11 x N A R04 02 00 1 12 x R02 30 01 Network It is highly recommended that customers intending to use MIP 5000 in Public Safety situations use a dedicated network for dispatching For non public safety situations a MIP 5000 can be placed on an existing customer network Network must support multicast addressing and be QoS enabled For complete network requirements see Specification Sheet on MOL or EYES U S Professional Price Pages Trunking Fixed Page 5 MIP 5000 VoIP RADIO CONSOLE Date 1 5 15 Models SUGGESTED RETAIL Personal Computer PC It is highly recommended that customers intending to use MIP 5000 in Public Safety situations purchase the 112538 Motorola certified HP desktop computer If not purchasing Motorola computers see Specification Sheet on MOL for Recommended Minimum Computer Specifications RO4 02 00 supports Windows 7 Professional Service Pack 1 32or 64 bit and Windows 8 1 Professional 64 Bit For Information Assurance Customers the TT2538 is still the only certified solution ORDERING REQUIREMENTS You must also order a DDN9867 MOTOTRBO Direct Connect Cable to connect the MOTOTRBO Gateway to the XPR 4550 or XPR 5550 Mobile The MIP 5000 gateways do not ship with punch blocks or cables for connecting to base stations or radios These must be ordered separately or provided by the customer See the Accessories sectio
27. ional or LTR Trunking Systems MODEL DESCRIPTION MSRP L3213 MC1000 Tone Remote Control 4 Frequency Maximum 2 Wire or 4 Wire 545 00 L3216 MC2000 Tone Remote Control 16 Frequency Maximum 2 Wire or 4 Wire Parallel Status Updating 1 300 00 13217 MC2500 Multi Channel Remote Control 2 482 00 For technical training of Motorola products please visit https learning motorolasolutions com U S Professional Price Pages Trunking Fixed Page 3 Mc1000 MC2000 amp MC2500 Date 1 5 15 DESKTOP CONTROLLERS SUGGESTED RETAIL ACCESSORIES MODEL DESCRIPTION MSRP Tone amp DC Remote Adapters includes AC Power Supply DDN7066 and Install Service Manual L3276 Tone Remote Adapter 695 00 L3277 DC Remote Adapter 552 00 General Accessories HLN9457 Hardware Kit for use with the Expanded Accessory Connector includes 6 95 16 connector pins five 5 8 wires with pins attached and an extra housing Extended Local Control Accessories for use with L3211 and L3214 DDN6337 Junction Box order appropriate cable below 399 00 For connecting up to 6 local control desksets to the station Radio Interface Cables for use with DDN6337 L3276 and L3277 DDN6338 Radio Interface Cable 10 Ft for use with MaxTrac 16 pin accessory connector required SM120 M1225 CDM750 CDM1250 72 00 CDM1550 amp CDM1550eLS DDN6340 Generic Radio Cable 10 Ft unterminated bare leads can also be used
28. kers 8 Subscriber to demonstrate RX and TX audio L3615 MIP 5000 1 Channel MOTOTRBO Demo Kit 750 00 Kit Includes 1 1 Channel MIP 5000 Software 2 1 MIP 5000 MOTOTRBO Gateway 3 1 MIP 5000 MOTOTRBO Direct Connect Cable Limited to 1 Kit Per Dealer Site Location 712538 Z420 Low Tier Workstation with Windows 7 Pro 64 Bit SP1 2 550 00 A desktop or laptop computer meeting MIP 5000 specifications DDN1612 SW Based IRR USB HASP with License Sound Card and Speakers for Windows 7 Kit includes software based 2 935 00 Instant Recall Recorder IRR CD USB HASP protection key Sound Blaster XFI Xtreme sound and a Set of PC speakers A set of PC speakers are included to facilitate the playback audio from the telephone and radio lines CDN6673 Set of 2 PC Speakers 46 00 DSO17BLK 17 INCH NON TOUCH MONITOR BLACK 1 180 00 DSO19BLK 19 LCD Black No Touch 1 520 00 DSO17BLKTS 17 LCD Black with Touch 2 134 00 Audio DDN9492 MIPSOOO Basic Model USB Headset Jackbox 500 00 Supports 1 Plantronics two prong headset base and quick disconnect top 1 footswitch BLN6732 and 1 gooseneck Microphone B1914 DDN9493 MIP5000 Enhanced Model USB Headset Jackbox 575 00 Supports 1 Plantronics two prong headset base and quick disconnect top 1 footswitch BLN6732 and 1 gooseneck Microphone B1914 also provides port for Call Director logging Recorder or External Pager port B1914 MCC Series Desktop Gooseneck Microphone 250 00 Provides one desktop style
29. me simulcast channel frequency CA01951AA ADD ANALOG CONVENTIONAL VOTING SOFTWARE CA01951AA supports analog transmit and receive operation when connected to SpectraTAC DIGITAC and other TRC comparators in a voting channel configuration 6 Conventional Features Choose the appropriate optional system feature options if required CA01504AA ADD ANTENNA RELAY CA01504AA required for base stations with a single antenna and allows one antenna to be used for both transmit and receive signals CA01503AA ADD FALL BACK IN CABINET REPEAT SIMULCAST CA01503AA enables the station to continue to receive and transmit when communication with the comparator is lost CA01947AA ADD RECEIVER SCAN OPERATION CA01947AA provides the ability to scan for qualified activity on up to 16 receive frequencies The receive frequencies are assigned in the 16 programmable channel personalities Scan operation can be suspended and resumed by TRC WildCard progamming CA01950AA ADD CONV MULTI NAC MULTI PL CA01950AA enables multiple PL tones analog or multiple NACs digital P25 Network Access Codes to be detected on a single channel Each of the 16 channel personalities can be configured with a list of PL tones and NACs to use for receiver qualifiers CA01954AA ADD WILDCARD w GPIO CA01954AA provides configurable inputs and outputs with a programmable set of event action tables for implementing custom base radio interface applications CA01955AA ADD MAIN S
30. microphone Includes transmit and monitor buttons an 18 gooseneck shaft and a 10 foot cable Compatible for use near CRT monitors BLN6732 Foot Switch Tradition 106 00 For technical training of Motorola products please visit https learning motorolasolutions com U S Professional Price Pages Trunking Fixed Page 8 MIP 5000 VoIP RADIO CONSOLE Date 1 5 15 Accessories SUGGESTED RETAIL Model Number Description MSRP MOTOTRBO Gateway Radio Interface Cable DDN9867 MOTOTRBO XPR4550 and XPR 5550 Direct Connect Cable 159 00 Digital GW Radio Interface Cables DDN1463 APX 7500 Mobile Direct Connect Cable 230 00 DDN8350 MCS2000 III Direct Connect Cable 200 00 DDN8351 Consolette W9 Direct Connect Cable 100 00 DDN8352 CDM1550 Series Direct Connect Cable 100 00 Local GW Radio Interface Cables DDN6338 Radio Interface Cable 4 Use with MAXTRAC M1225 SM50 SM120 CDM1550 For connecting MAXTRAC M1225 72 00 SMSO SM120 CDM750 CDM1250 and CDM1550 family radios with Local Junction Box DDN6337 and TRC DC Remote Adapters L3276 L3277 DDN6340 Generic Radio Cable with Unterminated Bare Leads For use with Local Junction Box DDN6337 and TRC DC 50 00 Remote Adapters L3276 L3277 DDN6699 Radio Interface Cable For the MCS2000 138 00 Headset Tops pick at least 1 headset top RMN5077 Supraplus Single Muff Headset 110 00 RMN5078 Supraplus NC Single Muff Headset 149 00 RMN5079 Supraplus Dual Muff Headse
31. n Step 3 can be purchased with part number CDN6112 Each CDN6112 can support up to 4 modules MODEL NUMBER DESCRIPTION MCN Modules DDN1388 MCN RCD Software and HIB IP Module DDN1385 MCN GPIO 1208C Input Output Module CDN6119 AIB ASTROTAC Interface Module CDN6121 CIB Comparator Interface Module Software Expansion DDN1295 MCN SW LIC OPT Client Expansion for 4 Additional Clients Power Supply CDN6116 Power Supply MCN120 VAC Network Cables and Terminators CDN6123 Cable Accessory Network 9 IN CDN6124 Cable Accessory Network 3 FT CDN6125 Cable Accessory Network 10 FT CDN6126 Cable Accessory Network 25 FT CDN6127 Cable Accessory Network 100 FT CDN6115 Network Terminator Standard 78K Systems Parallel Input Output Cables CDN6129 Cable Accessory 25 PR Male Male 10 FT CDN6130 Cable Accessory 25 PR Male Male 25 FT Serial Cables CDN6132 Cable Kit HIB PC AT XT 6 FT CDN6131 Cable Accessory AIB Comparator 10 FT Manuals CDN6110 HIB Hardware Guide DDN1402 MCN Server Software Manual DDN1386 GPIO Hardware Guide CDN6107 AIB Hardware Guide CDN6109 CIB Hardware Guide Rack Mounting DDN1387 MCN Accessory Rack Mount Kit Dual A B CDN6112 Rack Mount Quad Size A MSRP 7 000 00 1 075 00 1 900 00 775 00 2 765 00 84 00 21 00 21 00 21 00 38 00 92 00 10 00 36 00 55 00 30 00 55 00 20 00 28 00 20 00 20 00 20 00 75 00 78 00
32. n below for cables that can be used for connecting to various radios Headset Jackbox Every MIP 5000 operator position requires either a Basic or an Enhanced headset Jackbox The Jackbox is needed for all standard non USB accessories Each position requires a minimum of 1 and can support a maximum of 3 of any combination of Jackboxes TT05515AA is the option for the Basic Headset Jackbox and TT05522AA is the option for the Enhanced headset Jackbox A headset s may be used with the MIP 5000 Console Each headset must be connected to a MIP 5000 USB Basic or Enhanced Jackbox A headset consists of two parts a base and a top A choice of two bases CDN6281 and CDN6282 and several tops is provided The MIP 5000 supports a maximum of two headsets per operator position Upgrades Upgrades to RO4 02 00 are available at no charge Labor for upgrade installation is not reimbursable To order contact System Support Center at 800 221 7144 option 4 on the call tree and request that a software case be opened Existing System Expansion All new orders for Software and Gateways will ship with the latest release software RO4 02 00 Adding Gateways If adding gateways onto an existing RO4 01 01 system or earlier gateways will automatically downgrade during the installation process to match the software release running in the system Adding Operator Positions If adding new operator positions to an existing RO4 01 01 system or earlier you will be required t
33. n the MIP 5000 console and the MCN RCD Client Server Software can support up to 192 inputs and 128 outputs Ordering Requirements Order the MCN RCD Software with HIB IP DDN1388 this will allow up to 4 MIP 5000 operator positions clients to share the I O module status If more than 4 operator positions are required than the MCN SW Lic Opt Client Expansion for 4 STEP 2 Order 1 power supply CDN6116 with every HIB IP Module STEP 3 Order the appropriate modules for the application A maximum of 16 modules can be supported per HIB IP e For General Purpose Aux I Os order DDN1385 GPIO Each DDN1385A can control 12 inputs and 8 outputs e For interfacing to ASTRO TAC Comparators order CDN6119 AIB e For interfacing to SPECTRA TAC Comparator order CDN6121 CIB Order 1 power supply CDN6116 for eve ry 4 modules ordered in Step 3 e Example 1 If you order 2 DDN1385 and 2 CDN6119 then order 1 CDN6116 e Example 2 If you order 3 DDN1385 and 2 CDN6121 then order 2 CDN6116 Order the same number of network cables as the Quantity of modules ordered in Step 3 The following Network cable lengths are available e CABLE ASSY NETWORK 9 INCHES CDN6123 e CABLE ASSY NETWORK 3 FT CDN6124 e CABLE ASSY NETWORK 10 FT CDN6125 e CABLE ASSY NETWORK 25 FT CDN6126 e CABLE ASSY NETWORK 100 FT CDN6127 Note If rack mounting the 9 inch cable should be used from module to module To connect between rackmount shelves the 3 FT cable should
34. nter Multi Select Paging Encode Allows you to selectively call a pager portable or mobile unit and Multi Tasking eliminate the need to purchase a stand alone encoder The following schemes are All Mute supported QC II 2 Tone 5 Tone 6 Tone Digital Dial Reach 1 1 GE 99 NEC 5 amp 6 DTMF or Custom A and B tones Aux I O s Securenet Coded Clear Operation Supports positive mode control Tone Notes 1 Intercom Allows communication between desksets without accessing the radio frequency 2 Up to 10 remotes can be used in parallel 3 MC Series remotes are not compatible with 900 MHz MaxTrac Mobiles 4 MC2000 and MC2500 units require RSS programming software 5 MC2500 unselect speaker port supports a passive speaker only 6 For unexpected out of box failures or quality issues the MC Series and MC3000 must be returned for warranty repair Please refer to the user s manual Units will be replaced if they are sent in a total of 3 times and continue to exhibit the same problem 7 For L3276 amp L3277 radio interface cable not included Must be ordered separately DC and Tone Remote Control Models Only For DC and Tone Remote Control If base is not remote capable a Remote Adapter is required see L3276 amp L3277 The L3213 Desksets support channel steering between 4 talkgroups over conventional or LTR Trunking Systems The L3216 and L3217 Desksets support channel steering between 15 talkgroups over convent
35. o upgrade the entire system all Operator positions CSDM and gateways to RO4 02 00 All operator positions and gateways in a MIP 5000 system must run the same version of software Instant Recall Recorder IRR The Instant Recall Recorder IRR software with MIP 5000 allows users to record audio digitally on the MIP 5000 Operator position Operator TX audio Select and Unselect RX audio Telephone Call Director Audio or any combination may be recorded If PC is Order Includes 1T2538A MIP 5000 Certified PC DDN1612 IRR Software amp License Soundcard and PC Speakers Customer PC w o Speakers DDN1612 IRR Software amp License Soundcard and PC Speakers DDN1611 Customer PC with Speakers amp IRR Software amp License Soundcard DDN1118 Note MIP 5000 with IRR on a laptop is not a supported configuration Link to price pages Dual Instant Recall Recorder Pre Install Support Motorola now offers MIP 5000 Installers an exclusive conference call with a knowledgeable Technical Support consultant prior to going on site If you previously have not installed a MIP 5000 system we highly recommend this call at no charge to you to ensure a successful install Motorola will cover the first 30 Minutes of the call any additional support beyond the 30 Minutes will follow the standard MIP 5000 support process Call 1 800 221 7144 option 2 3 3 Network Equipment Model Number Description CLN1836 HP Switch 2610 24 2 250 00 U S
36. onal Price Pages Conventional Fixed Page 4 BATTERY REVERTING CHARGER Date 8 3 15 FOR USE WITH MOTOROLA SUGGESTED RETAIL MTR2000 BASE STATIONS These battery reverting charger units charge and maintain the radio battery bank in a float type application The system provides automatic reverting to a battery bank when main AC power fails and also provides separate charging capability BASIC PACKAGE INCLUDES Auto Transfer Circuit Float and Automatic Equalize Circuitry Low Voltage Disconnect Output Current Indicator Stand Alone Box Temperature Compensation Capability optional Auto Equalize Charger Failure Indicator Battery On Indicator Rack Mountable Overvoltage Protection amp Indicator MODEL DESCRIPTION MSRP L1883 Battery Reverting Charger 14 volt 12 volt nominal for 30 Watt 40 Watt and Receive Only models 1 619 00 L18384 Battery Reverting Charger 28 volt 24 volt nominal 25 100 Watt 1 619 00 Periferals CDN6226A Cable Interface Station to Charger 66 15 CDN6227A Cable Interface Battery to Charger 85 70 TDN9879A Temperature Sensor 40 00 For technical training of Motorola products please visit https learning motorolasolutions com U S Professional Price Pages Conventional Fixed Page 5 GTR 8000 Date 1 5 15 GTR 8000 ANALOG CONVENTIONAL BASE RADIO SUGGESTED RETAIL GENERAL INFORMATION The GTR 8000 Base Radio orderable model T7039 is a future ready bas
37. ption brings the total number of circulators to three X676BG ADD UHF EXTERNAL DUAL CIRCULATOR 380 512 MHZ X676BG adds 2 circulators and a low pass filter that are mounted on a 2 rack unit tray for the UHF band 380 524 MHz Since the power amplifier has one circulator this option brings the total number of circulators to three All Tx frequencies must fall within one of the following subbands 380 403 403 470 or X676B ADD EXT DUAL CIRCULATOR 136 146 MHZ X676BJ adds 2 circulators and a low pass filter that are mounted on a 2 rack unit tray for the VHF band 136 146 MHz Since the power amplifier has one circulator this option brings the total number of circulators to three X676BI ADD EXT DUAL CIRCULATOR 144 160 MHZ X676BI adds 2 circulators and a low pass filter that are mounted on a 2 rack unit tray for the VHF band 144 160 MHz Since the power amplifier has one circulator this option brings the total number of circulators to three X676BH ADD EXT DUAL CIRCULATOR 158 174 MHZ X676BH adds 2 circulators and a low pass filter that are mounted on a 2 rack unit tray for the VHF band 158 174 MHz Since the power amplifier has one circulator this option brings the total number of circulators to three U S Professional Price Pages Conventional Fixed Page 8 GTR 8000 Date 1 5 15 GTR 8000 ANALOG CONVENTIONAL BASE RADIO SUGGESTED RETAIL GENERAL INFORMATION 7 Peripherals continued
38. t 117 00 RMN5080 Supraplus NC Dual Muff Headset 139 00 RLN6098 HDST Module Base w PTT 15 Cbl 210 00 RLN6099 HDST Module Base w PTT 25 Cbl 242 00 RackMount Kit DDN8900 MIP5000 Rackmount Kit Holds maximum of 2 gateways 225 00 Information Assurance to be used with TT2538 computer TT2134 MIP5000 Information Assurance Transparent Hardening Kit CD 50 00 TT2135 MIP5000 Information Assurance Fully Hardened Kit CD 50 00 U S Professional Price Pages Trunking Fixed Page 9 Date 1 5 15 MONITORING amp CONTROL NETWORK MCN FOR MIP 5000 CONSOLE SUGGESTED RETAIL The MIP 5000 console system now supports Auxiliary I Os via CTI s Monitoring ControlNetwork Remote Comparator Display MCN RCD Client Server Software This gt software provides real time monitoring and control for a wide range of devices including doors alarms light switches and other general purpose Auxiliary I O applications In addition the MCN RCD system supports comparator voting displays at the MIP 5000 P console operator position The MCN RCD Client Server Software is an IP based solution and can run on the same network as the MIP 5000 console The MCN RCD system consists of two parts The MCN RCD Server Software with HIB IP Module and the specific interface module for the application The interface module s can be General Purpose I Os Comparator module or a combination of the two The paired solution betwee
39. the 4 wire interface on a DIU the MIP 5000 can talk listen change frequency and select coded clear However MIP 5000 does not support the ACIM link functionality of the DIU Digital Gateway L3484 acts as a virtual control head for specific Motorola radios or Consolettes via the SB9600 protocol MIP 5000 will display the Alias ID if the individual Subscriber is configured to send it MIP 5000 will provide the dispatcher access to the same number of frequencies the radio is capable of Mobiles supported are e APX 7500 Mobile in a tray 05 Control Head Remote Mount e MCS2000 Model III e Spectra Spectra Plus Consolette W9 e ASTRO XTL5000 Consolette W9 e CDM1550 LS LS Requires Remote Kit RLN4802 and Remote Cable Kit RKN4077 MIP 5000 Release APX 7500 Firmware Version R04 01 00 R09 00 00 or later R04 01 01 R09 00 00 or later R04 02 00 R10 00 00 or later MOTOTRBO Gateway L3598 acts as a virtual control head for the MOTOTRBO XPR4550 control station via the XCMP protocol MIP5000 will display the Alias ID when in analog or TRBO digital mode MIP5000 will provide the dispatcher access to the same number of frequencies the radio is capable of MOTOTRBO system types supported are e Conventional e IP Site Connect e Linked Capacity Plus e Capacity Plus e Connect Plus Requires Connect Plus System Release 1 4b MIP 5000 Release XPR 4550 Firmware Version XPR 5550 Firmware Vers
40. the network and configured in the Console System Database Manager CSDM These configuration files can be saved on each operator position to allow the dispatcher to access and control different combinations of radio resources up to 48 at a time MIP 5000 consists of Gateways which connect the radios to the Network and Operator Position components including MIP 5000 application software Personal Computer PC and Audio accessories Gateways There are 4 types of gateways available in a MIP 5000 system to interface to radios Local Tone Digital and MOTOTRBO Gateways have a one to one relationship to radios One gateway is required for each radio controlled Local Gateway L3482 controls radios typically Mobiles in a Tray via Microphone and Speaker connection and will support up to 16 frequency select depending on radio capability Radio Interface Cables e Prewired cable for CDM Family DDN6338 e Prewired cable for MCS2000 DDN6699 e Generic radio cable for use with XTL family DDN6340 Requires field install of XTL accessory connector e Map universal cable for use with MOTOTRBO XPR family PMKN4018 Requires field install of DB25 for local gateway Tone Gateway L3483 controls base stations or repeaters with tone control signaling which will support up to 16 frequency select depending on radio capability via 600 Ohm lease lines In addition the tone gateway will also support E amp M signaling DIU With a tone gateway connected to
41. tion 4 5 MHz 6 MHz 433 00 HFD8189 VHF Duplexer 155 162 MHz minimum amp maximum freq separation 4 5 MHz 6 MHz 486 00 HFD8190 VHF Duplexer 162 174 MHz minimum amp maximum freq separation 4 5 MHz 6 MHz 478 00 UHF Duplexers HFE8400 UHF Duplexer 406 450 MHz minimum amp maximum freq separation 5 MHz 390 00 HFE8401 UHF Duplexer 470 490 MHz minimum amp maximum freq separation 3 MHz 438 00 Only required if using a Duplexer HKKN4002 CDR700 amp CDR500 Internal Duplexer amp Antenna Cable 85 00 HKKN4001 CDR700 amp CDR500 External Duplexer amp Antenna Cable required when using separate 80 00 transmit and receive antennas or duplexers that do not fit into CDR500 amp CDR700 housings Antenna Accessories RDD4527 VHF 3dB Gain Antenna 150 158 MHz 361 00 RDE4556 UHF 3 8dB Gain Antenna 450 470 MHz 421 00 Contact RPSD for additional antennas Mounting Accessories HLN9169 CDR500 amp GR500 Wall amp 19 Panel Mount 100 00 HKLN4117 CDR500 Radio amp Duplexer Mounting Bracket Retrofit Kit This bracket allows the installation 110 00 of CDM Series mobiles within a GR500 repeater housing General Accessories HLN9455 CDR700 GR1225 RKR1225 amp GR400 X Pand Battery Revert amp Float Maintenance Charger 155 00 HPN9033 CDR700 GR1225 amp RKR1225 Power Supply 201 60 HPN9005 CDR500 amp GR500 Power Supply 492 00 AARMN4026 Enhanced Keypad Microphone Supports Remote Monitor
42. uous use will alarm 7 days prior to failure decreasing maintenance costs and minimizing downtime RESOURCES GTR 8000 Base Radio Manual https motonline mot solutions com Member ContentManagement resourcecenter asp 6871023P25 A Quick Guide for Replacing a Conventional QUANTAR with a GTR 8000 Base Radio https motonline mot solutions com Member ContentManagement resourcecenter asp ORDERING REQUIREMENTS NOTE All stations on a Simulcast channel should be of the same station type 1 Main Model The following main model must be ordered for a GTR 8000 Base Radio T7039A GTR 8000 BASE RADIO Ordering Note Only order a quantity of one of the T7039A per line item This model number will automatically generate internally added options for all hardware components that are not part of an orderable option such as cabling 2 Frequency Band and Power Level Enter the Frequency Band option CA00855AA ADD 700 800 MHZ MID POWER X640AL ADD UHF R2 MID POWER 435 524 X530BG ADD VHF MID POWER 136 174 X448AA ADD UHF R1 MID POWER 380 435 Ordering Note One TX and one RX frequency must be specified and will be collected at the main model level When ordering analog conventional software option CA01949AA TX and RX frequencies can be equal when the antenna relay option CA01504A lt A is ordered 700 800 MHz Frequency Rules for CA00855AA RX Range 794 00625 824 99375 MHz TX Range 764 00625 775 99375 MHz and 851 00625 86
43. wide range of voltages and frequencies NEW IMPROVED WARRANTY TWO Year Motorola Standard Warranty Please refer to Motorola Online Resource Center for further product level information and technical configuration Ordering requirements MTR3000 Base Station Repeater Satellite Receiver Product Planner amp Sales Ordering Guide ORDERING REQUIREMENTS 1 Order a quantity of one T7713A per line item 2 You must enter the exact customer frequencies at the time order is placed Frequency selection option also mandatory 3 Customer Programming Software CPS is required to program 4 Preselector is optional for the MTR3000 Satellite Receiver Refer to the Product Planner Sales Ordering Guide for Further rules 5 AC cable comes standard The DC cable is optional DUE TO THE COMPLEX NATURE OF CERTAIN ORDERABLE OPTION CONFIGURATIONS WE STRONGLY RECOMMEND REVIEW OF THE PRODUCT PLANNER AND SALES amp ORDERING GUIDE MODEL DESCRIPTION MSRP T7713 MTR3000 RECEIVER 1 400 00 MODEL DESCRIPTION MSRP e SELECT FREQUENCY OPTION XA00045AA ADD UHF 403 470 MHz 3 400 00 XA00046AA ADD UHF 470 524MHz 3 400 00 XA00047AA ADD VHF 136 174MHZ 3 400 00 XA00048AA ADD 800MHz 806 870 3 600 00 XA00049AA ADD 900MHz 896 941 3 600 00 MODEL DESCRIPTION MSRP Software RVN5115 Portable Mobile and Repeater Customer Programming Software CPS Package Software package includes CPS Air Tracer 265
Download Pdf Manuals
Related Search