pro edger - littlewonder.uk.com
Contents
1. Never leave a machine unattended Turn off blade and stop engine before leaving the machine Use extreme caution when pulling machine towards you Stop operation if someone approaches STARTING Start according to instructions in this manual or on the machine Before attempting to start the engine make sure the blade is disengaged When starting the engine make sure hands and feet are clear of the blade Do not engage blade at full throttle Throttle to idle or lowest possible engine speed Do not change engine governor settings or overspeed the engine Operating the engine at excessive speed can increase the hazard of personal injury A INTERRUPTING OPERATION Before leaving the operator s position shut off engine Stop the engine disengage the blade and wait until the blade stops rotating before refueling before making height adjustment unless the adjustment can be made from the operator s position Stop the engine disengage the blade and disconnect the spark plug wire before clearing blockages or unclogging before checking cleaning or working on the machine after striking a foreign object Inspect the machine for damage and have repairs made as needed before restarting if the machine begins to vibrate abnormally shut off machine immediately Inspect and have repairs made as needed before restarting PRO EDGER except for repairs or adjustments as specifically noted such as f2. blade Pushing the lever forward makes the engine speed go faster while pulling the lever back slows down the speed of the engine BELT SLACKENER LEVER C Rotate the lever towards the operator to disengage the blade Rotate the lever away from the operator to engage the blade ENGINE START STOP SWITCH D Move to the OFF position to stop the engine Move to the ON position before starting the engine CONTROLS FUEL VALVE F Move to the OFF position to shut off the fuel whenever transporting the machine by trailer or truck or during storage Move to the ON position before starting the engine CHOKE G Move to the CHOKE position to apply the choke Move to the RUN position to remove the choke OPERATION PRE OPERATION CHECK LIST OWNER S RESPONSIBILITY e Review and follow all safety rules and safety decal instructions e Check that all safety decals are installed and in good condition Replace if damaged e Check to make sure all shields and guards are properly installed and in good condition e Check that all hardware is properly installed and secured e Check to be sure engine is free of dirt and debris Pay particular attention to the cooling fins governor parts and muffler Clean air intake screen Check air cleaner service as necessary e Check all lubrication points and grease as instructed in manual e Inspect area and remove stones branches or other
3. but we also rely on your good sense and care to achieve accident free operation For best protection study the manuals thoroughly Learn the proper operation of all controls Observe all safety precautions Follow all instructions and warnings completely Do not remove or defeat any safety features Make sure those who operate this machine are as well informed and careful in its use as you are See a Little Wonder dealer for any service or parts needed Little Wonder service ensures that you continue to receive the best results possible from Little Wonder products You can trust Little Wonder replacement parts because they are manufactured with the same high precision and quality as the original parts Little Wonder designs and builds its equipment to serve many years in a safe and productive manner For longest life use this machine only as directed in the manuals keep it in good repair and follow safety warnings and instructions You ll always be glad you did Little Wonder Schiller Grounds Care Inc 1028 Street Road Southampton PA 18966 4217 TABLE OF CONTENTS FIGURES SAFETY LABELS CONTROLS OPERATION MAINTENANCE STORAGE TROUBLESHOOTING DECLARATION OF CONFORMITY WARRANTY This Operator Manual is part of the machine Suppliers of both new and second hand machines must make sure that this manual is provided with the machine 01 2013 SAFETY NOTICE Unauthorized modifications may present extreme safety hazards
4. condition of belts for damage or wear e Replace broken worn or damaged belts Belt Replacement e Stop the engine and disconnect the spark plug wire before attempting to replace any belt Lubrication e Lubricate cutter head shaft P N 131A cutter head bracket P N 100C and key P N 138 at slip rotation points every 8 hours 11 STORAGE STORAGE To prevent possible explosion or ignition of vaporized fuel do not store equipment with fuel in tank or carburetor in an enclosure with open flame for example a furnace or water heater pilot Before the equipment is put into storage for any period exceeding 30 days Drain all fuel from the fuel tank and fuel lines Start the engine and run until all the fuel is used from the carburetor float bowl and the engine stops While the engine is still warm drain the crankcase oil and replace with the proper weight oil corresponding to the season the equipment will be next used Remove the spark plug and squirt a small amount of engine oil into the cylinder Slowly pull the starter a few times to distribute oil in the cylinder and reinstall the spark plug Top off if necessary See engine manual for details 12 PRO EDGER To put the equipment into service after an extended period of storage 1 Check for loose parts and tighten if necessary 2 Fill the fuel tank and then check the engine oil level 3 Start the engine and check for fuel leaks Repair
5. container opening until fueling is complete Do not use a nozzle lock open device If fuel is spilled on clothing change it immediately SAFETY STORAGE SAFETY Stop the engine and allow to cool before storing Drain the fuel tank outdoors only Store fuel in an approved container in a cool dry place Keep the machine and fuel containers in a locked storage place to prevent tampering and to keep children from playing with them Do not store the fuel container or equipment with gasoline in the tank inside a building where fumes may reach an open flame or spark Appliances such as furnaces and water heaters with a pilot light have an open flame Keep gasoline storage area free of grass leaves and excessive grease to reduce fire hazard Clean debris from cutting units drives mufflers and engine to help prevent fires Clean up any spilled gasoline or oil in the storage area LABELS CRO EDGER WARNING LABELS Warning labels are an important part of the safety system incorporated in this machine Replace labels if damaged or illegible Key C P N 4168758 A 4168758 Key B P N 4168759 Key A P N 4168356 kde 2 a C som PRO EDGER CONTROLS BLADE HEIGHT ADJUSTMENT LEVER A Rotate the lever away from the operator to raise the blade Rotate the lever toward the operator to lower the blade THROTTLE CONTROL B Controls engine speed and controls speed of the
6. debris buildup or grease Never attempt to make adjustments while the engine is running except for repairs or adjustments as specifically noted such as for carburetor adjustment where the engine must be running Keep hands and feet clear of moving parts in these circumstances FUEL SAFETY PRO EDGER A WARNING Lh Gasoline petrol is flammable gas oline petrol vapors are explosive Use extra care when handling Store only in containers specifically designed for fuel When refueling or checking fuel level Stop the engine and allow to cool Do not smoke Refuel outdoors only Use a funnel Do not overfill If fuel is spilled do not attempt to start the engine until the spill is cleaned up and vapors have cleared Replace caps on fuel containers and tanks securely Sparks from static electricity can start fires or cause explosions Flowing fuel can generate static electricity To prevent static electricity sparks Keep containers electrically grounded Do not fill containers in a vehicle or on a truck or trailer bed with a plastic liner Fill containers on the ground away from the vehicle When practical remove gasoline petrol powered equipment from the truck or trailer and refuel it on the ground If equipment must be refueled on the truck or trailer refuel from a portable container rather than a dispenser nozzle Keep the dispenser nozzle in contact with the rim of the fuel tank or
7. to operators and bystanders and could also result in product damage Schiller Grounds Care Inc strongly warns against rejects and disclaims any modifications add on accessories or product alterations that are not designed developed tested and approved by Schiller Grounds Care Inc Engineering Department Any Schiller Grounds Care Inc product that is altered modified or changed in any manner not specifically authorized after original manufacture including the addition of after market accessories or component parts not specifically approved by Schiller Grounds Care Inc will result in the Schiller Grounds Care Inc Warranty being voided Any and all liability for personal injury and or property damage caused by any unauthorized modifications add on accessories or products not approved by Schiller Grounds Care Inc will be considered the responsibility of the individual s or company designing and or making such changes Schiller Grounds Care Inc will vigorously pursue full indemnification and costs from any party responsible for such unauthorized post manufacture modifications and or accessories should personal injury and or property damage result G SCHILLER tp ih 1028 STREET ROAD SOUTHHAMPTON PA 18966 U S A 2010 xxxKG xx xKW I Ln MODEL DESCRIPTION MODEL NUMBER SERIAL NUMBER PRO EDGER This symbol means ATTENTION BECOME ALERT Your safety and the safety of others is involved Signal word de
8. LITTLE WONDER PRO EDGER 6232 00 59 Owners Manual and Safety Instructions for LITTLE WONDER Pro Edger MAN 4168761 Rev A 01 2013 Original Language Instructions OPERATOR S MANUAL CALIFORNIA Proposition 65 Warning A WARNING Diesel engine exhaust and some The engine exhaust from this product of its constituents are known to the contains chemicals known to the State State of California to cause cancer of California to cause cancer birth A and other reproductive defects or other reproductive harm CALIFORNIA Proposition 65 Warning Battery posts terminals wiring insulation and related accessories contain lead and lead compounds chemicals known to the State of California to cause cancer and birth defects or other reproductive harm WASH HANDS AFTER HANDLING PRO EDGER IMPORTANT MESSAGE Thank you for purchasing this Little Wonder product You have purchased a world class product one of the best designed and built anywhere This machine comes with an Operation and Safety Manual Parts and Service Manual and Engine Manual The useful life and good service you receive from this machine depends to a large extent on how well you read and understand these manuals Treat your machine properly lubricate and adjust it as instructed and it will give you many years of reliable service Your safe use of this Little Wonder product is one of our prime design objectives Many safety features are built in
9. aintenance whether performed by you or a registered dealer is at your expense LITTLE WONDER MAKES NO EXPRESS OR IMPLIED WARRANTIES REPRESENTATIONS OR PROMISES EXCEPT THOSE CONTAINED HEREIN THERE ARE NO OTHER WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ALL WARRANTIES OTHER THAN THE EXPRESS WARRANTY SET FORTH ABOVE ARE SPECIFICALLY DISCLAIMED THE DURATION OF ANY IMPLIED WARRANTY INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IS LIMITED TO THE DURATION OF THIS WRITTEN LIMITED WARRANTY LITTLE WONDER DISCLAIMS ALL LIABILITY FOR INDIRECT INCIDENTAL AND OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE USE OF THE LITTLE WONDER PRO EDGER PRODUCTS COVERED BY THIS WARRANTY SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND OR DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THAT ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE LITTLE WONDER SCHILLER GROUNDS CARE INC 1028 STREET ROAD P O BOX 38 SOUTHAMPTON PA 18966 PHONE 877 596 6337 FAX 215 357 8045 www littlewonder com 2013 Schiller Grounds Care Inc All Rights Reserved
10. anders Carbon monoxide present in the exhaust is an odorless and deadly gas Never start or run the engine where exhaust fumes can collect Provide enough fresh air to keep fumes from getting too strong Replace any warning decals that become illegible immediately DAILY MAINTENANCE Hardware e Tighten any hardware nuts bolts etc that are found loose e Replace any broken or missing hardware nuts bolts cotter pins etc e Check to see that set screws on pulley are tight Engine See engine manual for air cleaner service intervals and servicing procedure Oil Check oil level daily Top off as needed Change engine oil after the first 5 hours of operation Then change as recommended by the engine manufacturer 1 Remove the drain plug and drain oil while engine is warm 2 Replace the drain plug remove dipstick and fill with new oil See engine manual for oil specifications 3 Wipe off any oil on unit 4 Start and run engine for 30 seconds Stop engine 5 Wait 30 seconds then re check oil level 6 Top off as necessary See engine manual for details MAINTENANCE Blade Service Stop engine and remove spark plug wire before servicing blade e Check tightness of the blade nut prior to each use Guards e Check condition of guards for damage or wear e Replace broken worn or damaged shield plates 27 BELT GUARD MUST BE PARALLEL FOR THE EDGER TO DISENGAGE PROPERLY Belts e Check
11. any leaks before operating the unit PRO EDGER TROUBLESHOOTING GUIDE TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION A B Engine will not start Loss of power hard starting Engine will not idle properly Engine runs hot or overheats Control mechanisms for depth blade will not function 13 Out of gasoline il Spark plug lead wire loose or 2 disconnected Defective spark plug Throttle control lever not in proper position Engine flooded or flooding Stale or contaminated gasoline Engine switch off Oil level low Spark plug lead wire loose Defective spark plug Carburetor out of adjustment Air cleaner dirty Air vents clogged or plugged Idle speed too slow Spark plug gap incorrect Air cleaner dirty Oil level low Engine cooling fins or baffles clogged with dirt and debris Carburetor out of adjustment Parts bent distorted worn out or missing Fill gasoline tank Reconnect spark plug lead wire Replace spark plug Move throttle control lever to start position Start engine with choke fully open Drain clean tank and system and refill with fresh gasoline Turn engine switch to ON position Fill crankcase to proper oil level Tighten spark plug lead wire Replace spark plug Properly adjust carburetor Clean and service air cleaner See the engine Operation and Maintenance illustrations Clean vent in gas
12. arting the engine secure and hold the edger handle with your left hand 3 Refer to your Engine Operator Owner Manual for Engine Starting Instructions 4 Once the engine starts slowly move the choke to the run position and set the throttle control lever to desired speed NOTE A warm engine requires less choking than a cold engine The engine speed should be kept to the minimum consistent with the job at hand Speeds higher than necessary will only cause undue wear and tear A speed half way between fast and slow is normally adequate Tougher jobs may require higher speed STOPPING OPERATION 1 Pull throttle lever towards you to STOP position 2 Turn engine switch to OFF position SETTING DEPTH OF BLADE 1 Place left hand on upper handle 2 Grasp lever P N 228 with right hand and pull to the right which disengages lever from ratchet segment on handle Move lever forward or backward along ratchet segment and insert key on lever into notch on ratchet at the desired depth Moving lever forward decreases depth moving lever backward increases depth PRO EDGER MAINTENANCE WARNING Stop the engine and remove spark plug wire before performing any maintenance When replacement parts are required use genuine Little Wonder parts or parts with equivalent characteristics including type strength and material Failure to do so may result in product malfunction and possible injury to the operator and or byst
13. by the manufacturer e Ifan operator or mechanic cannot read English it is the owner s responsibility to explain this material to them If any portion of this material is unclear contact your factory representative for clarification e Be sure the area is clear of pets and people especially young children Never assume they will remain where you last saw them Stop the machine if any enter the area e Clear the area of objects such as rocks toys wire or any other debris that may be thrown or get tangled in the blade e Become familiar with the safe operation of the equipment operator controls and safety signs Be prepared to stop the engine quickly in an emergency Do not operate or allow another e Only use in daylight or in good artificial light person to operate this machine if there are any e Keep in mind that the operator or user is respon questions about safety sible for accidents or hazards occurring to other All operators and mechanics should be trained The people or their property owner is responsible for training the users e Wear appropriate clothing including safety goggles or safety glasses with side shields when operating MULTIPLE OPERATORS Wear substantial footwear and long pants Do not operate barefoot or wearing open sandals Long e Keep a safe distance between operators when hair loose clothing or jewelry may get tangled in working together moving parts e Wear appropriate hearing prot
14. ection MACHINE PREPARATION e Never allow children unskilled or improperly trained people to operate this equipment Local regulations can restrict the age of the operator Read engine manual e Do not tamper with or defeat safety devices Keep guards shields and interlock safety devices in place Do not put hands or feet near or under rotating and in proper working condition They are for your parts protection Never pick up or carry the unit while the engine Is Keep all fasteners such as nuts bolts and pins well PUNUNG secured e Keep warning labels and this operator s manual Visually inspect blade and the assembly for wear or legible and intact Replacement labels and manuals damage Replace worn or damaged parts are available from the factory e Verify that machine and attachments if any are in e Do not operate machine while under the influence good operating condition of drugs or alcohol or any other condition of impairment e Do not engage blade until ready to use e The owner user can prevent and is responsible for accidents or injuries occurring to themselves other people or property SAFETY OPERATING SAFELY IN GENERAL Use extra care when loading or unloading the machine into a trailer or truck Never operate without guards plates or other safety protective devices in place Do not run the engine in an enclosed area where dangerous carbon monoxide fumes can collect
15. finitions The signal words below are used to identify levels of hazard seriousness These words appear in this manual and on the safety labels attached to Schiller Grounds Care Inc machines For your safety and the safety of others read and follow the information given with these signal words and or the symbol shown above DANGER indicates an imminently hazardous situation which if not avoided WILL result in death or serious injury WARNING indicates a potentially hazardous situation which if not avoided COULD result in death or serious injury CAUTION indicates a potentially hazardous situation which if not avoided MAY result in minor or moderate injury It may also be used to alert against unsafe practices or property damage CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided MAY result in property damage MODEL NUMBER This number appears on sales literature technical manuals and price lists and serial tag SERIAL NUMBER This number appears only on your unit It contains the model number fol lowed consecutively by the serial number Use this number when ordering parts or seeking war ranty information PRO EDGER SAFETY OPERATOR PREPARATION amp TRAINING READ THE OPERATION amp SAFETY MANUAL SITE PREPARATION amp CIRCUMSTANCES e Evaluate the terrain to determine how to safely perform the job Only use accessories and attachments approved
16. hard objects that might be thrown causing injury or damage e Check that there are no exposed underground utilities in the work area FUELING Gasoline petrol is extremely flammable and highly explosive under certain conditions BE SURE to install fuel cap after fueling e Fill fuel tank with good quality clean unleaded regu lar petrol gasoline to the level recommended by the engine manufacturer e Use a funnel to avoid spilling lA ih Do it outdoors Do not smoke Stop engine allow to cool Do not overfill Clean up spilled fuel 10 PRO EDGER BEFORE STARTING THE ENGINE e Read the operator manual and engine manual e Be familiar with all controls how each functions and what each operates e Check the engine oil level and add if necessary Follow the engine manufacturers recommendations per the engine manual supplied with the machine e Open the fuel valve e Choke For cold starts set the choke lever to the CHOKE position For warm starts attempt to start without the choke first to avoid flooding If the engine does not start then use the choke STARTING THE ENGINE A WARNING ALL LITTLE WONDER EDGERS ARE SHIPPED WITHOUT OIL WHEN FILLING OIL USE SAE 30 OIL REFER TO THE ENGINE MANUFACTURER S INSTRUCTION MANUAL FOR PROPER ENGINE OPERATION INSTRUCTIONS 1 For easier starting remove belt tension by pulling up the belt slackener lever P N 167 2 2 Prior to st
17. inal product and any warranty on the replaced parts will expire coincident with the original product warranty If you think your LITTLE WONDER PRO EDGER is defective in material or workmanship you must return it to a registered dealer with a valid sales receipt or to our factory at 1028 Street Rd Southampton PA 18966 Transportation charges to ship your product to us or a registered dealer must be borne by you Engines for all gasoline powered products are warranted separately by the engine manufacturer Therefore there are no warranties made expressed or implied for engines for gasoline powered products by Little Wonder LITTLE WONDER assumes no responsibility in the event that the product was not assembled or used in compli ance with any assembly care safety or operating instructions contained in the Owner s Manual or information accompanying the product This limited warranty does not cover damages or defects due to normal wear and tear lack of reasonable and proper maintenance failure to follow operating instructions or Owner s Manual misuse lack of proper storage or accidents nor does it cover routine maintenance parts and service This limited warranty does not cover any defects due to repairs or alterations made to the product made by anyone other than LITTLE WONDER or its registered dealers You must maintain your LITTLE WONDER PRO EDGER by following the maintenance procedures described in the owner s manual Such routine m
18. nment Directive 2000 14 EC Vibration DINECIIVG xidscincconacsansaneawndensntersearedenunts 2002 44 EC Non Road EMISSIONS siascawsesdccucedvasiswmadeawenrmarewt aa 2004 26 EC Sound Sound levels were determined in accordance with Directives 2000 14 EC and EN ISO 3744 2010 Guaranteed Sound Power Level 101 dB Model 6232 00 59 Sound PrESSUN Ci diccswctrenntciuneduaaberensannsmonnden 8 7 dB Model 6232 00 59 Vibration Hand arm vibration was measured at the right and left operator handles as per ISO 5349 1 2001 and ISO 5349 2 2001 Only the highest of the left and right readings is given Levels were calculated using ISO DIS 5395 1 in accordance with 2002 44 EC Guaranteed Vibration Level 5 5 m s Model 6232 00 59 Intended Use and Limits This machine is intended for edging of grass around driveways walkways and path edges 14 LITTLE 1 YEAR LIMITED SERVICE AND WONDER TORETE EEA pee ences All LITTLE WONDER PRO EDGERS are warranted against defects in material and workmanship for a period of one 1 year from the date of purchase under the following terms and conditions LITTLE WONDER will repair or replace at its option any part or parts of the product found to be defective in ma terial or workmanship during the warranty period Warranty repairs and replacements will be made without charge for parts or labor All parts replaced under warranty will be considered as part of the orig
19. oline tank cap and carburetor Adjust carburetor idle speed or idle mixture Set spark plug gap see your Engine Manual Clean and service air cleaner See the engine Operation and Maintenance illustrations Fill crankcase to proper oil level Clean and remove obstructions Readjust carburetor Inspect control mechanism and re pair or replace damaged worn out or missing components 13 EC Declaration of Conformity 4168674 REVA The Undersigned Manufacturer Schiller Grounds Care Inc 1028 Street Road Southampton PA 18966 Kurt Knudsen Director of Operations Date 7th February 2013 EU Authorized Representative Earlsmere Limited Unit 18 Valley Road Station Road Industrial Estate Wombwell Barnsley South Yorkshire S73 OBS UK Jim White Managing Director Date 7th February 2013 Declare that the machine described below Make amp IOC ctecactanasctatenbdecedatcconcsancsect Little Wonder Pro Edger ONC O ONY cctctawacsuruinea siinon riie Dia Lawn Edger OS che see EE E E E A 6232 00 59 OWING E A Honda GX120 SC tet E E E AE 3600 rpm Net installed powef ccceeeeeeeeeeeeens 2 6kKW 3 5 HP Complies with the provisions of the following European directives and Amendments and the Regulations transposing it into national law Machinery Directive ccccceeeeeeeeeeeneeenes 2006 42 EC EMC Directv aecasscsannretindaraeatnicenmuinsenararades 2004 108 EC Noise in the Enviro
20. or carburetor adjustment where the engine must be running Keep hands and feet clear of moving parts in these circumstances Allow the blade to come to a complete stop when stopping operation to clear blockages unclog inspect the machine do maintenance or repair Reduce the throttle setting during engine shutdown and if the engine is provided with a shutoff valve turn the fuel off at the conclusion of operation MAINTENANCE SAFETY IN GENERAL Maintain machine according to manufacturer s schedule and instructions for maximum safety and best results Park machine on level ground Never allow untrained personnel to service machine Guards should only be removed by a qualified technician for maintenance or service Replace when work is completed Adjust or repair only after the engine has been stopped and the blade has stopped moving Disconnect spark plug wire before doing any maintenance Replace parts if worn damaged or faulty For best results always replace with parts recommended by the manufacturer Do not dismantle the machine without releasing or restraining forces which may cause parts to move suddenly Provide adequate support e g jack stands for lifted machine or parts if working beneath Do not put hands or feet near or under rotating parts Clean up spilled oil or fuel thoroughly Replace faulty mufflers To reduce fire hazards keep the engine muffler and fuel storage area free of grass leaves
Download Pdf Manuals
Related Search