AWG5012B Option 09 and AWG50BUP Option S39 User Manual
Contents
1. Description Part number Quantity Converter Box TTL Event to LVDS TekLink 850 0108 xx 1 each Connector Adapter AWG5000B and AWG7000B Series Product 020 2945 xx 1 each Software CD TekLink Cable 200 cm 174 5019 xx 1 each User Manual printed 071 2674 xx 1 each Controls and Connectors 1 Table Event Input connector See page 3 Table Event Input Connector 2 TekLink connector 2 TTL Event to TekLink LVDS Connector Adapter User Manual Table Event Input Connector Connect an event signal to the Table Event Input connector The Table Event Input connector Table Event Input accepts TTL level signals from 0 0 V to 5 0 V DC Peak AC The can accept four bit Table Jump 012 3 Strobe connector is a standard 9 pin D type oo ER oo By connecting the connector adapter OE 0000 to your AWG5012B the instrument 9 signals The Table Jump can define up to 16 possible logic levels of the Event Input lines Strobe Signal Pin NO OMAN DOF WY Signal STROBE EVENT Bit3 EVENT Bit2 EVENT Bit1 EVENT Bit0 GND GND GND GND Installation Direction INPUT INPUT INPUT INPUT INPUT You can input one strobe signal in addition to the four event signals The strobe signal controls the timing of reading the event signals m When Strobe is set to Off the instrument reads the event signals at the timing of every two internal clock cycles and updates the event value if a state t2. AWG5012B Option 09 and AWG50BUP Option 39 TTL Event to TekLink LVDS Connector Adapter User Manual DULL TTD Tektronix 071 2674 00 7 AWG5012B Option 09 and AWG50BUP Option S39 TTL Event to TekLink LVDS Connector Adapter User Manual www tektronix com Tektronix 071 2674 00 4 Copyright O Tektronix All rights reserved Licensed software products are owned by Tektronix or its subsidiaries or suppliers and are protected by national copyright laws and international treaty provisions Tektronix products are covered by U S and foreign patents issued and pending Information in this publication supersedes that in all previously published material Specifications and price change privileges reserved TEKTRONIX and TEK are registered trademarks of Tektronix Inc TekLink is a registered trademark of Tektronix Inc Contacting Tektronix Tektronix Inc 14200 SW Karl Braun Drive P O Box 500 Beaverton OR 97077 USA For product information sales service and technical support In North America call 1 800 833 9200 Worldwide visit www tektronix com to find contacts in your area Warranty Tektronix warrants that this product will be free from defects in materials and workmanship for a period of one 1 year from the date of shipment If any such product proves defective during this warranty period Tektronix at its option either will repair the defective product without charge for parts and labor or will provide a re
3. Compliance EC Declaration of Conformity EMC Meets intent of Directive 2004 108 EC for Electromagnetic Compatibility Compliance was demonstrated to the following specifications as listed in the Official Journal of the European Communities EN 61326 1 2006 EMC requirements for electrical equipment for measurement control and laboratory use 1 CISPR 11 2003 Radiated and conducted emissions Group 1 Class A IEC 61000 4 2 2001 Electrostatic discharge immunity IEC 61000 4 3 2002 RF electromagnetic field immunity IEC 61000 4 4 2004 Electrical fast transient burst immunity IEC 61000 4 5 2001 Power line surge immunity IEC 61000 4 6 2003 Conducted RF immunity IEC 61000 4 11 2004 Voltage dips and interruptions immunity 3 EN 61000 3 2 2006 AC power line harmonic emissions EN 61000 3 3 1995 Voltage changes fluctuations and flicker TTL Event to TekLink LVDS Connector Adapter User Manual V Compliance Information vi European Contact Tektronix UK Ltd Western Peninsula Western Road Bracknell RG12 1RF United Kingdom 1 This product is intended for use in nonresidential areas only Use in residential areas may cause electromagnetic interference 2 Toensure compliance with the EMC standards listed here high quality shielded interface cables should be used 3 Performance Criterion C applied at the 7090 25 cycle Voltage Dip and the 096 250 cycle Voltage Interruption test levels IEC 61000 4 11 Australia New Zeala
4. fied or integrated with other products when the effect of such modification or integration increases the time or difficulty of servicing the product THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCT IN LIEU OF ANY OTHER WARRANTIES EXPRESS OR IMPLIED TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE TEKTRONIX RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES W2 15AUG04 Table of Contents Table of Contents General Safety SUMMAI scenes chee ene tala te reti de externen ne sand ETDn KAANE DE sue ENTE densa raise ME Mm iii Compliance Information HTTP V EMG Compliance ani IP MTM V Environmental Considerations 3s epe ree erect bake a mE ES vende cides vu ee radi reu Re rd DRS vii uc MTM viii Mods p c E A E T E E E EE A E viii Software Upgrades ss daca ver iden Ee eL RR ERRHN HERO RAIFERXRY ERR aang ERRARE canine Eee viii Related DOCUMENTS sinc EET viii WAST AMON cash tena ca T m 1 Producis oot taie dtes ete ya tee eerie Maca HUM LU US E E ERE UEM soon gad 1 GE INC T TEUPES 1 Controls and Connectors 2 tdeo
5. ied as Monitoring and Control equipment and is outside the scope of the 2002 95 EC RoHS Directive TTL Event to TekLink LVDS Connector Adapter User Manual vii Preface Preface This manual describes the installation and operation of the TTL Event to TekLink LVDS Connector Adapter The connector adapter converts a TTL signal to an event signal for the AWG5012B arbitrary waveform generator AWG5012B TekLink connector TTL to LVDS Generator TTL signal converter box Key Features The AWG5012B Option 09 supports the following features W Subsequence m Table jump NOTE The AWG software must be version 3 3 or later to enable the Option 09 features To check the software version of your AWG5012B select Help gt About Tektronix AWG from the menu bar Software Upgrades Software upgrades are available Occasionally new versions of software for your instrument may become available on the Tektronix Web site To check for upgrades 1 Use your Web browser to go to www tektronix com software 2 Enter the product name AWG5012B to find available software upgrades If you purchased the AWG50BUP Option S39 Field Upgrade Kit you can use the Product SW CD that came with the kit to upgrade your AWG5012B Related Documents Review the following for the location of related information for your instrument To read about Use these documents Installation and operation Quick Start User Manual Provides general
6. nd Declaration of Conformity EMC Complies with the EMC provision of the Radiocommunications Act per the following standard in accordance with ACMA m CISPR 11 2003 Radiated and Conducted Emissions Group 1 Class A in accordance with EN 61326 1 2006 TTL Event to TekLink LVDS Connector Adapter User Manual Compliance Information Environmental Considerations This section provides information about the environmental impact of the product Product End of Life Handling Observe the following guidelines when recycling an instrument or component Equipment Recycling Production of this equipment required the extraction and use of natural resources The equipment may contain substances that could be harmful to the environment or human health if improperly handled at the product s end of life In order to avoid release of such substances into the environment and to reduce the use of natural resources we encourage you to recycle this product in an appropriate system that will ensure that most of the materials are reused or recycled appropriately This symbol indicates that this product complies with the applicable European Union requirements according to Directives 2002 96 EC and 2006 66 EC on waste electrical and electronic equipment WEEE and batteries For information about recycling options check the Support Service section of the Tektronix Web site www tektronix com Restriction of Hazardous Substances This product has been classif
7. nput impedance Pull up to 4 5 V by 2 2 kO register Output connector type 40 pin TekLink connector Output level LVDS Atmospherics Characteristic Description Temperature Operating 10 C to 40 C Nonoperating 20 C to 60 C TTL Event to TekLink LVDS Connector Adapter User Manual 7 Specifications Atmospherics cont Characteristic Description Relative humidity Operating 5 to 80 no condensation maximum wet bulb temperature 29 C Nonoperating 5 to 90 no condensation maximum wet bulb temperature 29 C Altitude Operating Up to 3 000 m approximately 10 000 feet Maximum operating temperature decreases 1 C each 300 m above 1 5 km Nonoperating Up to 12 000 m approximately 40 000 feet Physical characteristics Characteristic Description Height typical 47 8 mm 1 882 in Width typical 134 4 mm 5 291 in Depth typical 134 0 mm 5 275 in Weight typical 600 g 1 32 Ib 8 TTL Event to TekLink LVDS Connector Adapter User Manual
8. nternal circuitry Screws should enter the chassis 0 4 in 1 03 cm 3 Mount the connector adapter using two 88 90 mm 6 32 screws of appropriate length 3 500 in SUM NOTE Some rackmount kits have gt aaa provisions for mounting accessories such as ail 8 700 in s the connector adapter TTL Event to TekLink LVDS Connector Adapter User Manual 5 Installation 6 TTL Event to TekLink LVDS Connector Adapter User Manual Specifications Specifications Table Event Input AWG5012B option 09 Characteristic Description Number of Event Jump Up to 16 destination Strobe On Off selectable Minimum pulse width 64 ns Latency to analog output Max 650 ns 1 2 Gsps typical Max 1300 ns 650 Msps From D type connector on the TTL to LVDS converter to Analog output when Asynchronous Jump is selected Hold off time typical Maximum 500 sample clock cycles when Asynchronous Jump is selected TTL Event to LVDS TekLink Converter Characteristic Description Input connector type 9 pin D sub female Input signals and pin 54321 1 STROBE assignment 2 3 Event signal O00O0 0 3 2 Event signal 0000 4 1 Event signal 5 0 Event signal 9 8 7 6 6 Signal ground GND 7 Signal ground GND 8 Signal ground GND 9 Signal ground GND Input level TTL level m Input voltage range 0 V to 5 V High level input voltage 2 V to 5 V m Low level input voltage 0 V to 0 8 V I
9. operating information overviews In depth operation and User online help Provides detailed instructions for using instrument functions Access the user interface help user online help from the Help button or Help menu for information on controls and elements on screen Programmer commands Programmer online help Includes the syntax of GPIB commands Access the programmer online help from the Help menu The programmer PDF manual is also available on the document CD Service information Service manual The service manual is a PDF only manual and it is available on the Tektronix Web site at www tektronix com manuals viii TTL Event to TekLink LVDS Connector Adapter User Manual Installation Installation Unpack the connector adapter and check that you received all of the items listed below as parts list Check the Tektronix Web site www tektronix com for the most current information Products The TTL Event to LVDS Connector Adapter can be used only with the AWG5012B m AWG5012B Option 09 Subsequence and Table Jump AWG50BUP Option S39 Upgrade to Option 09 for the AWG5012B Parts List Table 1 AWG5012B Option 09 Description Part number Quantity Converter Box TTL Event to LVDS TekLink 850 0108 xx 1 each Connector Adapter TekLink Cable 200 cm 174 5019 xx 1 each User Manual printed 071 2674 xx 1 each TTL Event to TekLink LVDS Connector Adapter User Manual Installation Table 2 AWGS0BUP Option S39
10. placement in exchange for the defective product Parts modules and replacement products used by Tektronix for warranty work may be new or reconditioned to like new performance All replaced parts modules and products become the property of Tektronix In order to obtain service under this warranty Customer must notify Tektronix of the defect before the expiration of the warranty period and make suitable arrangements for the performance of service Customer shall be responsible for packaging and shipping the defective product to the service center designated by Tektronix with shipping charges prepaid Tektronix shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Tektronix service center is located Customer shall be responsible for paying all shipping charges duties taxes and any other charges for products returned to any other locations This warranty shall not apply to any defect failure or damage caused by improper use or improper or inadequate maintenance and care Tektronix shall not be obligated to furnish service under this warranty a to repair damage resulting from attempts by personnel other than Tektronix representatives to install repair or service the product b to repair damage resulting from improper use or connection to incompatible equipment c to repair any damage or malfunction caused by the use of non Tektronix supplies or d to service a product that has been modi
11. ransition in the event signals are found m When Strobe is set to On the instrument reads the event signals when the strobe signal goes to low state Enable and updates the event value if a state transition in the event signals are found NOTE You cannot toggle the Strobe signal on and off using the screen interface or remote commands The Strobe definition in the sequence file can control the strobe signal input For more information about Strobe Signal and Sequence file refer to the user online help TTL Event to TekLink LVDS Connector Adapter User Manual Installation Connecting Cables NOTE Before connecting the following cables power off your instrument The power is supplied from your AWG5012B through a TekLink cable 1 Connect a TTL level signal to the Table Event Input connector x Ji l H 2 Use a TekLink cable to connect the 28 connector adapter and your AWG5012B if 0 0 al Y IC 4 TTL Event to TekLink LVDS Connector Adapter User Manual Installation Mounting the Connector Adapter You can mount the connector adapter to a surface such as an existing rackmount tray or to a bracket of your design by doing the following 1 Remove the four adhesive backed plastic feet from the connector adapter 2 Referto the dimensions shown in the illustration and drill holes in the mounting surface for two screws CAUTION Using screws that are too long will damage the i
12. rape edad rede lb eee es PER RE Aaa aE en PEE E E MERE bs odes sneaks 2 Table Event Input Connector 52e rebos eese etir o o ele er n Fan edge ehe ee bre SFr ed atout 3 Connecting eu c neneem 4 Mounting the Connector Adapter 52e eiiii ese eere eese cere dias rede ierra pd reed uin d d Re ES 5 SPECHCALIONS lE REUUm MMUUU T T 7 TTL Event to TekLink LVDS Connector Adapter User Manual i Table of Contents ii TTL Event to TekLink LVDS Connector Adapter User Manual General Safety Summary General Safety Summary Review the following safety precautions to avoid injury and prevent damage to this product or any products connected to it To avoid potential hazards use this product only as specified Only qualified personnel should perform service procedures While using this product you may need to access other parts of a larger system Read the safety sections of the other component manuals for warnings and cautions related to operating the system To Avoid Fire or Personal Injury Observe All Terminal Ratings To avoid fire or shock hazard observe all ratings and markings on the product Consult the product manual for further ratings information before making connections to the product The inputs are not rated for connection to mains or Category II Ill or IV circuits Do not apply a potential to any terminal including the common terminal that exceeds the maximum rating of that terminal Do Not Operate Without Cover
13. s Do not operate this product with covers or panels removed Do Not Operate With Suspected Failures If you suspect that there is damage to this product have it inspected by qualified service personnel Avoid Exposed Circuitry Do not touch exposed connections and components when power is present Do Not Operate in Wet Damp Conditions Do Not Operate in an Explosive Atmosphere Keep Product Surfaces Clean and Dry TTL Event to TekLink LVDS Connector Adapter User Manual iii General Safety Summary Terms in this Manual These terms may appear in this manual WARNING Warning statements identify conditions or practices that could result in injury or loss of life CAUTION Caution statements identify conditions or practices that could result in damage to this product or other property Symbols and Terms on the Product These terms may appear on the product m DANGER indicates an injury hazard immediately accessible as you read the marking amp WARNING indicates an injury hazard not immediately accessible as you read the marking m CAUTION indicates a hazard to property including the product The following symbol s may appear on the product A CAUTION Refer to Manual TTL Event to TekLink LVDS Connector Adapter User Manual Compliance Information Compliance Information This section lists the EMC electromagnetic compliance safety and environmental standards with which the instrument complies EMC
Download Pdf Manuals
Related Search