Home

Signed the Terms and Conditions and included it in

Contents

1. 40 Outlet Location s NEMA L5 20R 20 amp twist lock receptacles shall be provided in the following locations 220 VOLT RECEPTACLE S There shall be two 2 220 volt receptacles provided Wet Location All wet location receptacle outlets shall be of the grounding type with a wet location cover and installed in accordance with Section 210 7 Receptacles and Cord Connections of the NEC All wet location receptacles shall be installed not less than 24 from the ground Receptacles on off road vehicles shal be a minimum of 30 from the ground The face of any wet location receptacles shall be installed in a plane from vertical to not more than 45 degrees off vertical No receptacle shall be installed in a face up position Dry Location All receptacles located in a dry location shall be of the grounding type Receptacles shall not be less than 30 inches above the interior floor height Receptacle Wiring All wiring for both wet and dry locations shall be routed through liquid tight flexible conduit rated at not less than 194 degrees Each receptacle shall be wired to the panel board which shall have separate breakers for each receptacle Outlet Location s 220 volt receptacles shall be provided in the following locations D1 next to breaker panel and D3 110 220 VOLT OUTLET LOCATIONS The 110 220 volt outlets shall be located as follows 2 on rear of body one each side and 1 each side of pump compartment HANNAY ELE
2. ENGINE HIGH IDLE CONTROL The vehicle shall be equipped with an automatic high idle speed control which shall be pre set to operate when the engine is at a specified RPM to increase alternator output This device shall operate only when the master switch is activated and the transmission is in neutral with the parking brake set The device shall disengage when the operator depresses the brake pedal or the transmission is placed in gear and shall automatically re engage when the brake is released or when the transmission is placed in neutral ENGINE PROGRAMMING ROAD SPEED GOVERNOR The engine shall include programming which will govern the top speed of the vehicle AUXILIARY ENGINE BRAKE A Jacobs engine compression brake for the six 6 cylinder engine shall be provided The engine compression brake shall actuate the vehicle s brake lights when engaged A cutout relay shall be installed to disable the compression brake when in pump mode or when an ABS event occurs The engine brake shall activate upon 0 accelerator when in operation mode AUXILIARY ENGINE BRAKE CONTROL An engine compression brake control device shall be included The electronic control device shall monitor various conditions and shall activate the engine brake only if all of the following conditions are simultaneously detected e A valid gear ratio is detected e The driver has requested or enabled engine compression brake operation e The throttle is a
3. Installation of any portion of the 120 240 system by a dealer or service center will not be acceptable There shall be no exception to this requirement BREAKER PANEL BOARD Each individual circuit that is to be powered by the generator shall have a Branch Circuit Overcurrent Protection device circuit breaker The device shall be sized at not less than 15 amps in accordance with Section 240 3 Protection of Conductors of the NEC If more than 6 individual branch circuits are required on the apparatus the panelboard shall have a main breaker The panelboard shall be readily visible and located so that there is unimpeded access to the panelboard controls All line voltage conductors located in the main panelboard shall be individually and permanently identified The identification shall reference the wiring schematic or indicate the final termination point When pre wiring for future power sources or devices the unterminated ends shall be labeled showing function and wire size LOAD BALANCING The breaker panel shall be load balanced to allow the most efficient distribution of the AC load as possible BREAKER PANEL LOCATION The breaker panel shall be located on the front wall of the driver front compartment FROG DISPLAY There shall be a FROG D provided with the generator The FROG D shall automatically sense a generator signal and begin displaying information The digital meter display shall constantly monitor and display Voltage Freq
4. PUMP COMPARTMENT LIGHTS 2 Two Weldon 2025 compartment lights shall be provided to illuminate the iinterior of the pump compartment The lights shall function with the pump operators gauge panel lights ENGINE COMPARTMENT LIGHT A Weldon model 2025 light shall be provided and mounted over the engine on the engine compartment wall An on off switch shall be provided on the light to activate it DUAL ILI LED COMPARTMENT LIGHTING Each apparatus body compartment shall have two ILI track type L E D lights vertically mounted in the compartment The lights shall be constructed of an unbreakable type clear poly type flexible material housed in an aluminum extrusion A compartment that is considered a full height compartment shall each have two 48 long light sections and a low height or above wheel compartment shall each have two 18 long sections The lights shall function automatically and independently of other compartments when the compartment door is opened Compartment lighting systems that are controlled by a single dash mounted switch are not acceptable COMPARTMENT LIGHT SWITCHES Each hinged apparatus body door compartment shall have a magnetic style reed indicator switch Each switch shall be hermetically sealed rated to 10 000 000 cycles The reed shall be potted in the contact housing with polyurethane and the housings shall be molded fire retardant ABS plast ic The contact and magnetic housing shall snap lock in the bod
5. An auxiliary set of power and ground studs shall be provided and installed behind the electrical center cover with a 40 amp breaker The studs shall be 0 38 inch diameter and capable of carrying up to a 40 amp load switched with the master power switch ADDITIONAL POWER amp GROUND STUD An additional set of power and ground studs shall be provided and installed behind the electrical center cover with a 40 amp breaker The studs shall be 375 inch diameter and capable of carrying up to a 40 amp load switched with the master power switch EXTERIOR ELECTRICAL TERMINAL COATING All terminals exposed to the elements will be sprayed with a yellow protective rubberized coating to prevent corrosion ENGINE A 2007 FEDERAL EPA EMISSION COMPLIANT ENGINE HAS BEEN SELECTED THIS ENGINE IS SUBJECT TO AVAILABILITY ON HAND AT TIME OF PURCHASE AT SPARTAN CHASSIS TIME OF PURCHASE SIGNIFIES ACCEPTANCE BY SPARTAN CHASSIS OF A VALID PURCHASE ORDER WITH A FULLY COMPLETED ORDER FILE AND THE RETURN BY SPARTAN CHASSIS OF A WRITTEN CONFIRMATION TO PURCHASER WHICH INCLUDES AN ASSIGNED SALES ORDER NUMBER THIS CONFIRMATION MUST EXPRESSLY STATE THAT THE ENGINE SELECTION IS CONFIRMED AND WILL BE INCLUDED IN YOUR ORDER BASED ON UPCOMING 2010 FEDERAL EPA EMISSION CHANGES 2007 FEDERAL EPA EMISSION COMPLIANT ENGINES ARE IN LIMITED SUPPLY AND INVENTORIES COULD BE DEPLETED AT ANY MOMENT IF AT TIME OF PURCHASE AT SPARTAN CHASSIS THE SELECTED ENGINE IS NO LONGER A
6. GEARBOX MIDSHIP PUMP GEARBOX MODEL MIDSHIP PUMP RATIO Addl Pwr amp Gnd Stud Bhd Sw Pnl 40A Mstr Sw Exterior Electrical Terminal Coating Spray On Plasti Dip Engine Diesel 425HP Cummins ISL must be pre 2010 year Cab Engine Tunnel Small Medium DPF Ctrl Regeneration Sw amp Inhibit Sw Engine Programming High Idle Speed 1250 RPM Engine High Idle Ctrl Automatic Engine Programming Road Speed Governor Enabled Aux Engine Brake Jacobs Aux Engine Brake Ctrl Off Low High Sw Pnl Fluid Fills Fwd For Med Displacement Cap Elec Engine Oil Level Indicator Engine Warranty Cummins 5 Year 100 000 Miles Rmt Throttle Harness PSG Fire Rsrch In Control 300 400 Side Mnt Engine Program Rmt Throttle Off Engine Programming Idle Speed 700 RPM Engine Fan Drive Clutch Engine Cooling Sys Medium Disp Cap Engine Coolant Extended Life Elec Low Coolant Level Indicator Engine Pump Heat Exchanger Coolant Hoses Silicone Engine Air Intake Filtration and Restriction Eng Exhaust Sys Under Frm RH Outboard Engine Exh Acc Exh Temp Mitigation Transmission GEN IV E Allison 3000 EVS Transmission Mode Programming 4th Startup Sth Mode Transmission Feature Programming I O Package 198 Pumper Elec Transmission Oil Level Indicator Transmission GEN IV E Shift Sel Key Pad Push Button 2nd Gear Pre Select Transmission Cooling System Transmission Warranty Allison 5 Year Driveline Spicer 1710 HD Midship Pump Jackshaft Only Midship Pump Gearbox
7. The crosslay compartment shall be constructed of 5052 smooth aluminum sheet material with a random brushed finish applied after fabrication Each crosslay shall be piped using 2 piping or high pressure hose incorporating a 2 ball valve with the control on the side mount pump operators panel 2 1 2 CROSSLAY PRECONNECT One 2 1 2 preconnected crosslays shall be provided and located above the side mount pump panel 10 The crosslay compartment shall be constructed of 5052 smooth aluminum sheet material with a random brushed finish applied after fabrication Each crosslay shall be piped using 2 1 2 piping or high pressure hose incorporating a 2 1 2 ball valve with the control on the side mount pump operators panel 1 1 3 4 CROSSLAY CAPACITY 200 FEET The 1 1 3 4 crosslay shall have the capacity to hold 200 feet of 1 3 4 fire hose and nozzle 2 1 3 4 CROSSLAY CAPACITY 200 FEET The 2 1 3 4 crosslay shall have the capacity to hold 200 feet of 1 3 4 fire hose and nozzle 1 2 1 2 CROSSLAY CAPACITY 150 FEET The 1 2 1 2 crosslay shall have the capacity to hold 150 feet of 2 1 2 fire hose and nozzle Two 2 Akron 8820 series discharge valves shall be utilized to control the 1 3 4 cross lay hose beds and shall be manually controlled from the pump operator s position The valves and piping shall be 2 One 1 Akron 8825 series discharge valve s shall be utilized on the 2 1 2 crosslay discharge s The valve
8. The warning system shall activate when any seat is occupied with a minimum of 60 pounds the corresponding seat belt remains unfastened and the park brake is released The warning system shall also activate when any seat is occupied the corresponding seat belt was fastened in an incorrect sequence and the park brake is released Once activated the visual indicators and audible alarm shall remain active until all occupied seats have the seat belts fastened OCCUPANCY ROLLOVER PROTECTION The vehicle shall include the Spartan Chassis RollTek rollover occupant protection system which shall secure occupants increase the survivable space within the cab and protect against head neck injuries in the event of a roll over accident The system shall function using a microprocessor controlled solid state sensing device which when the system detects a side roll shall provide instantaneous occupant protection less than 0 3 seconds from trigger to total deployment by automatically initiating the following sequence 1 The seat belt shall tighten around the occupant on all seats excluding theatre flip up style seating 2 The air suspension on each seat shall be reduced to its lowest position tightens belt around occupant and locking the seat in this position thereby providing more survivable space and minimizing head contact with the interior roof available when air suspension seats are specified 3 An inflatable curtain shall deploy which inc
9. The winch shall be equipped with 125 00 feet of 0 38 inch cable clevis hook and a 4 way roller fairlead The winch shall be operated through a 25 00 foot pendant with a hand held control The winch shall include a spring applied hydraulic released disc brake and counterbalance valve It shall feature an easy to use spring loaded clutch with clutch engagement indicator light AIR HORN The chassis shall include two 2 Hadley brand E Tone air horns which shall measure 24 00 inches long with a 6 00 inch round flare The air horns shall be trumpet style with a chrome finish on the exterior and a painted finish deep inside the trumpet AIR HORN LOCATION The air horns shall be recess mounted in the front bumper face on the left side of the bumper in the inboard and outboard positions relative to the left hand frame rail AIR HORN RESERVOIR One 1 air tank with a 1200 cubic inch reservoir shall be installed on the chassis to act as a supply tank for operating air horns The reservoir shall be isolated with a 90 PSI pressure protection valve on the reservoir supply side to prevent depletion of the air to the air brake system ELECTRONIC SIREN SPEAKER The bumper shall include one 1 Cast Products Inc model SA4301 100 watt speaker which shall be recess mounted within the bumper fascia The speaker shall include a flat mounting flange and be chrome in color ELECTRONIC SIREN SPEAKER LOCATION The electronic siren speaker shall
10. cold start system automatic load and temperature compensation integrated diagnostics system and other automated control features to protect system vehicle and operator The generator tray assembly shall be delivered with the cooler fan assembly mounted such that the hot air is exhausted straight up through an NFPA approved walking grate The body of the generator tray assembly including reservoir shall be 32 long x 13 5 wide x 17 high weighing approximately 185 pounds The hydraulic pump shall be driven by a chassis transmission mounted power take off PTO Ratings and Capacity Rating 12 000 watts peak 9 000 watts continuous Volts 120 240 volts Phase Single 4 wire Frequency 60 Hz Amperage 83 amps 120 volts or 42 amps 240 volts Engine speed at engagement Standard soft start feature allows for any 36 speed engagement Operation range 880 to 3120 RPM Testing The generator shall be tested in accordance with all current N F P A 1901 standards Notes All ratings and capacities shall be derived utilizing current NFPA 1901 test parameters HYDRAULIC GENERATOR START SWITCH CAB CONSOLE The hydraulic generator shall be located on the cab console There shall be an indicator light on the cab console that illuminates when the generator is running HYDRAULIC GENERATOR PTO HOT SHIFT TYPE The generator shall be powered by a Chelsea or Muncie Hot Shift Power Take Off A lighted and guarded switch shall
11. style of safety restraint The ABTS feature shall include a three point shoulder harness with the lap belt and automatic retractor as an integral part of the seat assembly The buckle portion of the seat belt shall extend from the seat base towards the driver position within easy reach of the occupant The minimum vertical dimension from the seat H point to the ceiling for this belted seating position shall be 35 00 inches This model of seat shall have successfully completed the static load tests by FMVSS 207 210 This testing shall include a simultaneous forward load of 3000 pounds each on the lap and shoulder belts and twenty 20 times the weight through the center of gravity This model of seat installed in the cab model as specified shall have successfully completed the dynamic sled testing using FMVSS 208 as a guide with the following accommodations In order to reflect the larger size outfitted firefighters the test dummy used shall be a 95th percentile hybrid III male weighing 225 pounds rather than the 50th percentile male dummy weighing 165 pounds as referenced in FMVSS 208 The model of seats shall also have successfully completed the flammability of materials used in the occupant compartments of motor vehicles as outlined in FMVSS 302 of which decides the burning rate of materials in the occupant compartments of motor vehicles SEAT BACK OFFICER The officer seat back shall include a Ziamatic brand Rol Loc mechanical self contai
12. the apparatus shall be fully disassembled for the paint process The apparatus body shall not be mounted on the chassis during the paint process Masking or taping off of any portion of the apparatus during the paint process shall not be acceptable All compartment doors shall be painted separate from the apparatus body All seams or flanges on the apparatus body shall be caulked or properly sealed to prevent moist ure accumulation in flanged areas PAINT PROCESS The apparatus body paint procedure shall consist of an eight 8 step finishing process as follows 1 Manual Surface Preparation All exposed metal surfaces on the apparatus exterior shall be thoroughly cleaned as per SSPC SP1 All imperfections on the exterior metal surface shall be removed or filled prior to the priming process All exposed metal shall be thoroughly abraded using a dual orbital air power sander as per SSPC SP3 2 Cleaning and Treatment All surfaces shall be chemically cleaned using PPG DX436 was and grease remover cleaning agent to remove all dirt Oil grease and metal oxides to ensure proper adhesion as per SSPC SP 1 3 Self etching Primer Application PPG Delfleet F3960 two component acid etching primer shall be applied to the bare metal as per bulletin DFT 041 4 Primer Surfacer Application PPG K36 two component urethane primer surfacer shall be applied to the acid etching primer 5 Dual Orbital Sanding The primer surfacer shall be thoroughly sanded
13. to allow individual removal of each ladder without disturbing any other ladder Pike Poles Storage for two straight handle pike poles shall be provided in the compartment ILI strip light DUO SAFETY 24 2 SECTION ALUMINUM LADDER There shall be one 1 Duo Safety model 900A 24 NFPA compliant 2 section aluminum extension ladder provided and mounted by the manufacturer DUO SAFETY 14 ALUMINUM ROOF LADDER There shall be one 1 Duo Safety model 775A 14 NFPA compliant aluminum roof ladder with folding hooks provided and mounted by the manufacturer DUO SAFETY 10 ALUMINUM FOLDING ATTIC LADDER There shall be one 1 Duo Safety model 585A 10 NFPA compliant aluminum folding attic ladder provided and mounted by the manufacturer HARD SUCTION COMPARTMENT IN HOSEBED ose bed for two 2 10 lengths of hard suction hose stacked one above the other The hose bed height shall be a minimum of 18 from the hose bed floor to the top of the hose bed to accommodate the suction hose mounts The rack shall be mounted to the hose bed divider brackets and shall be fully adjustable The hard suction mounts shall be constructed of minimum 1 8 smooth aluminum with brushed finish The upper and lower compartments shall be 9 x 9 x the depth of the hose bed The upper compartment shall be open on top Both compartments shall be open to the rear with no door HARD SUCTION HOSE FIRE DEPARTMENT PROVIDED The hard suction hose shall be prov
14. to be removed from the apparatus in a one piece modular section while leaving the body intact and without having to cut any sheet metal or welds HYPER FLEX PUMP MOUNTING The independent pump module assembly shall be mounted to the chassis frame rails with Hyper Flex vibration and shock isolators using a four 4 point mounting system Flexible neoprene pads especially engineered for the expected weight and torsional flexing of the pump module shall be incorporated into the system to eliminate chassis framerail flexing from transmitting harmful loads and twisting into the pump module STAINLESS STEEL PUMP COMPARTMENT CONSTRUCTION The entire pump compartment shall be constructed using only 304 marine grade stainless steel fabricated sheeting with a 4 annealed and polished finish on all exterior surfaces The pump compartment shall not require any finish painting Due to the extreme twisting and flexing that all fire apparatus are sub jected to aluminum shall not be used in any portion of the pump compartment structural support The use of any type of enclosed tubing that requires the use of self tapping or any other type of machine screw shall not be acceptable PUMP COMPARTMENT RUNNINGBOARDS The pump compartment side runningboards shall be constructed of NFPA compliant slip resistant aluminum treadbrite on stepping surfaces PUMP COMPARTMENT RIGHT SIDE ACCESS DOOR SIDE MOUNT A brushed stainless steel hinged access door shall be
15. wide x 26 usable depth the full height of the compartment The compartment shall have a roll up door with an opening 58 high x 63 wide The roll up door shall have a brushed satin finish PASSENGER S SIDE COMPARTMENT IN FRONT OF THE REAR WHEELS A compartment shall be provided in front of the rear wheels The compartment shall be 64 high x 48 75 wide x 26 usable depth the full height of the compartment The compartment shall have a roll up door with an opening 58 high x 42 wide The roll up door shall have a brushed satin finish PASSENGER S SIDE ABOVE WHEEL COMPARTMENT A compartment shall be provided above the rear wheels The compartment shall be 33 high x 62 wide x 26 usable depth The compartment shall have a roll up door with a door opening 30 high x 54 wide The roll up door shall have a brushed satin finish PASSENGER S SIDE COMPARTMENT BEHIND REAR WHEELS A compartment shall be provided behind the rear wheels The compartment shall be 64 high x 65 wide x 26 usable depth The compartment shall have a roll up door with an opening 58 high x 61 wide The roll up door shall have a brushed satin finish REAR FACE COMPARTMENT A rear compartment shall be provided on the apparatus just ahead of the rear step The compartment shall be a minimum of 30 useable depth The compartment shall have maximum height with selected apparatus options 23 REAR FACE COMPARTMENT DOOR ROLL UP The rear compartment shall have
16. 002 1514 002 1526 004 1502 019 5109 001 5101 002 5106 003 5102 001 5108 002 5104 002 5202 004 5203 002 5204 055 5209 002 SEAT CREW REAR FACING OUTER SEAT BACK REAR FACING OUTER SEAT MOUNTING REAR FACING OUTER OCCUPANCY ROLLOVER PROTECTION RFO SEAT BELT ORIENTATION CREW SEAT FORWARD FACING CENTER LOCATION SEAT CREW FORWARD FACING CENTER SEAT BACK FORWARD FACING CENTER SEAT MOUNTING FORWARD FACING CENTER OCCUPANCY ROLLOVER PROTECTION FFC SEAT FRAME FORWARD FACING SEAT FRAME FORWARD FACING STORAGE ACCESS CAB FRONT UNDERSEAT STORAGE ACCESS DOOR SEAT COMPARTMENT DOOR FINISH WINDSHIELD WIPER SYSTEM ELECTRONIC WINDSHIELD FLUID LEVEL INDICATOR CAB DOOR HARDWARE DOOR LOCKS DOOR LOCK LH REAR CAB COMPARTMENT DOOR LOCK RH REAR CAB COMPARTMENT GRAB HANDLES REARVIEW MIRRORS REARVIEW MIRROR HEAT SWITCH CAB FENDER MUD FLAPS FRONT CAB EXTERIOR FRONT amp SIDE EMBLEMS CAB EXTERIOR MODEL NAMEPLATE IGNITION BATTERY BATTERY TRAY BATTERY CABLE BATTERY JUMPER STUD ALTERNATOR BATTERY CONDITIONER BATTERY CONDITIONER DISPLAY ELECTRICAL INLET ELECTRICAL INLET LOCATION Seat Crew RFO Seats Inc Fixed Seat Back RFO SCBA Zico Rol Loc Seat Mounting RFO Rwd 2 Occupancy Rollover Protection RFO RollTek Seat Belt Orientation Crew Outboard Shoulder To Inboard Hip Seat FFC Location 2 Ctr Seat Crew FFC Seats Inc Flip up Seat Back FFC SCBA Zico Rol Loc Seat Mounting Forward Facing
17. 15 outlet with springloaded weatherproof covers The first wired outlet shall be a GFI type outlet with all downstream outlets being GFI protected A large handle shall be provided on the top of the box to allow a gloved firefighter to carry the box with ease The lighted box shall provide 360 degree lighting around the box which is capable of being seen from a minimum of 200 feet in complete darkness as per NFPA 1901 The box shall be designed to keep the exterior electrical components above 2 of standing water The box shall be listed for use in wet locations JUNCTION BOX HOLDER An aluminum treadbrite bracket shall be provided to hold the cord reel junction box 42 CORD REEL ROLLER ASSEMBLY WITH BALL STOP A roller assembly with ball stop shall be provided each cord reel reel The assembly shall be mounted in a location that will help deflect the cable hose from the surfaces adjacent to the reel FLUID CAPACITY LABEL A permanent plate shall be mounted in the driver s compartment specifying the quantity and type of the following fluids used in the apparatus if applicable for normal maintenance Engine Oil Engine Coolant Transmission Fluid Pump Transmission Fluid Pump Primer Fluid if applicable Drive Axle Fluid Air Conditioning Refrigerant Air Conditioning Lubrication Oil Power Steering Fluid 10 Cab Tilt Mechanism Fluid if applicable 11 Transfer Case Fluid 12 Equipment Rack Fluid if
18. 3 SCBA bottles with maximum dimensions of 6 75 diameter x 24 50 long A 1 wide loop of high visibility yellow webbing shall be installed in each compartment for each cylinder to be stored in the compartment The loop shall be designed to loop around the cylinder valve and prevent the cylinder from sliding out of the compartment if the door is not latched or fails PASSENGER FRONT WHEELWELL COMPARTMENT There shall be a compartment located in the passenger s side wheel well ahead of the rear axle to hold three 3 SCBA bottles with maximum dimensions of 6 75 diameter x 24 50 long A 1 wide loop of high visibility yellow webbing shall be installed in each compartment for each cylinder to be stored in the compartment The loop shall be designed to loop around the cylinder valve and prevent the cylinder from sliding out of the compartment if the door is not latched or fails 28 PASSENGER REAR WHEELWELL COMPARTMENT There shall be a compartment located in the passenger s side wheel well behind the rear axle to hold one set of Zico folding wheel chocks A safety chain shall be provided across the door opening The safety chain shall be designed to prevent the chocks from sliding out of the compartment if the door is not latched or fails DRIVER REAR WHEELWELL COMPARTMENT There shall be a compartment located in the driver s side wheel well behind the rear axle to hold up to 20 Ibs Of floor dry material A chute will be installed
19. ALUMINUM Extruded aluminum rubrails shall be provided on the apparatus body sides The rubrails shall have a brite finish with annodized coating to protect the finish The rubrails shall provide an integrated mounting location for the L E D side marker lights as well as the reflectors The rubrails shall be spaced from the apparatus body a minimum of 1 4 with poly spacers The rubrails must be bolted on to the apparatus body to allow easy replacement if damaged Rubrails that are permanently fastened to the apparatus body by welding or any other permanent method will not be acceptable NO EXCEPTION WILL BE ALLOWED TO THIS REQUIREMENT RUBRAIL ENDS The rubrail ends shall be capped with a high impact resistant black EPDM contoured block HOSEBED FLOORING The floor of the hose bed shall be constructed of fiber reinforced material The flooring shall be fabricated of T beam pultrusions in parallel connected with cross slats that are first mechanically bonded and then epoxied forming a large sheet The top portion of each T cross section shall measure 1 5 8 wide and 3 16 thick with beaded ends The vertical portion shall be 3 16 thick beading out at the bottom to a thickness of 1 2 and tall enough to result in an overall height of 1 The T sections shall be spaced 3 4 apart to allow for drainage and ventilation Each T beam shall be constructed utilizing a core of 250 000 continuous glass fiber strands that are high in resistan
20. ATC system shall apply the ABS when the drive wheels loose traction The system shall scale the electronic engine throttle back to prevent wheel spin while accelerating on ice or wet surfaces Additional handling capabilities shall include Roll Stability Control RSC which shall monitor the vehicles rollover threshold based on the lateral acceleration The system shall activate a computerized device which shall slow the vehicle when the threshold is exceeded in either direction Normal vehicle operation shall resume once the problematic conditions cease The RSC system shall be integral with the ABS and ATC systems A momentary rocker style switch shall be provided and properly labeled mud snow When the switch is pressed once the system shall allow a momentary wheel slip to obtain traction under extreme mud and snow conditions During this condition the ATC light and the light on the rocker switch shall blink continuously notifying the driver of activation Pressing the switch again shall deactivate the mud snow feature The Electronic Stability Control ESC unit is a functional extension of the electronic braking system It is able to detect any skidding of the vehicle about its vertical axis as well as any rollover tendency The control unit comprises an angular speed sensor that measures the vehicle s motion about the vertical axis caused for instance by cornering or by skidding on a slippery road surface An acceleration sensor measu
21. Alarm Ecco 575 Instrumentation Standard Cam Rr Box amp RH Teardrop w Mon Comm Ant Base RH Fwd Cab Rf Spartan Sply Comm Ant Cable Routing Behind LH Frt Seat Panel Layout Cab Exterior Protection Front Fire Extinguisher Ship Loose Road Safety Kit Ship Loose Door Keys for Manual Locks 4 Diagnostic Software RollTek w Interface Module Warranty Cab and Chassis 2011 1 Year Operation Manual Hard Copy Engine amp Transmission Operation Manual Hard Copy 2 Engine Service Manual Hard Copy Cummins ISC ISL 2 Transmission Service Manual Hard Copy Allison 3000 EVS 2 As Built Wiring Diagrams Hard Copy Customer Inspection End of Frame Cross Member Panel Visual Layout 5020 001 Panel Layout 1312A 005 SWITCH PANEL CENTER 18 12 6 SWITCHES LH 94 Label Connected From M en ee ee 2933 NN2 001 MASTER 1312A 005 5020PRT 002 2933 NN2 026 WARNING SIDE 2933 NN2 024 WARNING FRONT 2933 NN2 059 LIGHT BAR 1312A 005 5020PRT 006 1312A 005 5020PRT 007 1312A 005 5020PRT 008 1312A 005 5020PRT 009 1312A 005 5020PRT 010 1312A 005 5020PRT 01 1 1312A 005 5020PRT 012 5422 001 5020PRT 025 5424A 001 5020PRT 025 5423A 001 5020PRT 025 5426 002 5020PRT 025 2933 NN2 148 REAR DC SCENE 2933 NN2 146 LEFT DC SCENE 2933 NN2 147 RIGHT DC SCENE 1312A 005 5020PRT 016 1312A 005 5020PRT 017 2933 NN2 086 LOAD MNGR 5331 002 5020PRT 025 5316
22. Dash Spotlight Handheld Optronics KB4003 Do Not Move App Lt Flashing Red w Alarm Mstr Warn Sw Pnl Headlight Flasher Alternating Headlight Flasher Sw Pnl Inboard Frt Warn Lts Whelen 600 Series Super LED Chrm Bezel Inboard Frt Warn Lts Color Red w Clr Lens Frt Warn Sw Pnl Intersection Warn Lts Whelen 600 Series Super LED Int Warn Lts Color Red w Clr Lens Intersection Warn Lts Location Bumper Tail Side Warn Lts Whelen 700 Super LED Side Warn Lts Color Red w Clr Lens Side Warn Lts Location Lwr Mid Side amp Intersection Warn Sw Pnl Lightbar Prov Wire amp Mnt Spartan Supply Cab Frt Lightbar Whelen Freedom FN72QLED Layout 2 Lightbar Sw Pnl Int Dr Open Warn Lts Red Truck Lite 4 LED Flsh Siren Ctrl Head Whelen 295HFS2 Horn Btn Sel Sw Elec Horn Air Horn 5512 003 5505 002 5601 001 5706 041 5703 010 5708 010 5020 001 8814 002 8806 001 8807 002 8810 001 8811 002 8003 022 8030 001 8031 002 8032 009 8033 010 8805 002 8034 002 2124 002 AIR HORN ACTIVATION BACK UP ALARM INSTRUMENTATION CAMERA COMMUNICATION ANTENNA COMMUNICATION ANTENNA CABLE ROUTING PANEL LAYOUT CAB EXTERIOR PROTECTION FIRE EXTINGUISHER ROAD SAFETY KIT DOOR KEYS DIAGNOSTIC SOFTWARE ROLLTEK WARRANTY OPERATION MANUAL ENGINE amp TRANSMISSION OPERATION MANUAL ENGINE SERVICE MANUAL TRANSMISSION SERVICE MANUAL AS BUILT WIRING DIAGRAMS CUSTOMER INSPECTION EFCM REAR CROSSMEMBERS Air Horn Actv Strg Whl RH Ft Sw Back Up
23. OVERHEAD LIGHTS The cab shall include a two section incandescent dome lamp with a red and clear lens located over each door The dome lamps shall be rectangular in shape and shall measure approximately 9 50 inches in length X 5 00 inches in width with a black colored bezel The clear portion of each lamp shall be activated by opening the respective door and both the red and clear portions can be activated by individual switches on each lamp An additional incandescent three 3 light module with dual map lights shall be located over the engine tunnel which can be activated by individual switches on the lamp MAP LIGHTS A Roxter gooseneck style map light shall be provided The light shall have a clear bulb and a control switch on the base The light shall be located on the right hand side of the dash SPOTLIGHT The officer position shall include a 12 volt Optronics KB 4003 hand held spotlight which shall be mounted to the right of the engine tunnel The Optronics spot light shall offer 400 000 candle power It shall have a 10 00 foot coiled cord and a momentary push button switch DO NOT MOVE APPARATUS LIGHT The front headliner of the cab shall include a red flashing light located in the center for greatest visibility The light shall be 6 00 inches long X 2 50 inches wide X 1 75 inches high and shall be clearly labeled Do Not Move Apparatus In addition to the flashing red light an audible alarm shall be included which shall so
24. Safety model 6FP 6 fiberglass pike pole s shall be provided and mounted on the apparatus DUO SAFETY 8FP 8 FIBERGLASS PIKE POLE There shall be one 1 Duo Safety model 8FP 8 fiberglass pike pole shall be provided and mounted on the apparatus ZIAMATIC SAC 44 ALUMINUM WHEEL CHOCKS One set of two Zico model SAC 44 folding wheel chocks shall be provided Two underbody horizontal brackets SQCH 44 H shall be provided and installed under the body compartments 49 Page 1 TERMS AND CONDITIONS BID FORM Bids must be submitted on this form only and bear the handwritten signature of an authorized representative of the firm to be considered valid Unless otherwise stated by the City no bidder may withdraw his bid within a period of thirty 30 days after the date set for the opening of bids BID RETURN ENVELOPE ALL bids must be sealed and returned in the official City of Athens BID RETURN ENVELOPE included in the bid package If the bid documents you are returning exceed what this envelope can hold tape the completed bid return envelope to the OUTSIDE of the envelope package that you are using ALL bids must be SEALED and properly identified with the name and address of bidder the date time bid number and project title on the OUTSIDE of the bid return envelope INSURANCE A sheet of minimum INSURANCE REQUIREMENTS shall be attached to these terms and conditions when applicable This sheet is provided for you and your in
25. a roll up door DRIVER S SIDE REAR COMPARTMENT PARTITIONED The driver s side compartment behind the rear wheels shall have a removable panel seperating it from the rear facing compartment non transverse PASSENGER S SIDE REAR COMPARTMENT PARTITIONED The passenger s side compartment behind the rear wheels shall have a removable panel seperating it from the rear facing compartment non transverse UPPER DOOR JAMB EXTENSIONS The upper door jamb of the side compartments shall be extended upward on both sides providing a mounting area for side upper warning lights scenelighting large scale lettering etc The side shall be extended up to the same hieght as the side walls of the hosebed area LEFT SIDE COFFIN COMPARTMENTS Coffin compartments shall be provided above the side compartments on the left side The length of the compartments shall be the same as the length of the side compartments The width shall be the same as the upper depth of the side access compartments Maximum depth will be provided based on design of the apparatus Two aluminum treadbrite access doors shall be provided for access The doors shall have a 1 raised lip to keep water from running into the compartment The doors shall be fully weatherstripped and shall have dual flush mounted latches A single light shall be provided and located under the door jamb between the two access doors Floor tiles shall be provided on the floor of the compartment in any area that
26. all material covered by the order contract whichever is the later date Charges for boxing or cartage will not be allowed unless previously agreed upon Default in promised delivery and failure to comply with specifications authorizes the City to purchase supplies elsewhere and charge the difference to defaulting Vendor Bidder agrees to defend and save the City of Athens from and against all demands claims suits costs expenses damages and judgments based upon infringement of any patents relating to goods specified in this order or the ordinary use or operation of such goods by the City or use or operation of such goods in accordance with bidder s direction In case of error or discrepancy in the mathematics of the bid price the unit prices shall prevail By submission of a signed bid the bidder certifies total compliance with Title VI and Title VII of the Civil Rights Act of 1964 as amended and all regulations promulgated thereunder as the City of Athens does not discriminate based on Page 3 18 19 20 21 race color or national origin in federal or state sponsored programs pursuant to Title VI of the Civil Rights Act of 1964 42 USC 2000d Contracts and purchases will be made or entered into with the lowest responsible compliant bidder meeting specifications for the particular grade or class of material work or service desired in the best interest and advantage to the City of Athens Responsible bidder
27. and a rigid differential case for high axle strength and reduced maintenance The axle shall have heavy duty Hypoid gearing for longer life greater strength and quieter operation Industry standard wheel ends for compatibility with both disc and drum brakes and unitized oil seal technology to keep lubricant in and help prevent contaminant damage will be used REAR AXLE DIFFERENTIAL LUBRICATION The rear axle differential shall be lubricated with oil REAR AXLE WARRANTY The rear axle shall be warranted by Meritor for two 2 years with unlimited miles under the general service application Details of the Meritor warranty are provided on the PDF document attached to this option REAR WHEEL BEARING LUBRICATION The rear axle wheel bearings shall be lubricated with oil VEHICLE TOP SPEED The top speed of the vehicle shall be approximately 65 MPH 2 MPH at governed engine RPM REAR SUSPENSION The single rear axle shall feature a Reyco 79KB vari rate self leveling captive slipper type conventional multi leaf spring suspension with 57 50 inch X 3 00 inch springs One 1 adjustable and one 1 fixed torque rod shall be provided The rear suspension capacity shall be rated from 21 000 to 31 500 pounds FRONT TIRE The front tires shall be Michelin 385 65R 22 5 18PR J tubeless radial XZY3 mixed service tread The front tire stamped load capacity shall be 18 740 pounds per axle with a speed rating of 65 miles
28. and videos of said test shall be available upon request ELECTRICAL SYSTEM The chassis shall include a single starting electrical system which shall include a 12 volt direct current system suppressed per SAE J551 The wiring shall be appropriate gauge cross link with 311 degree Fahrenheit insulation All SAE wires in the chassis shall be color coded and shall include the circuit number and function where possible The wiring shall be protected by 275 degree Fahrenheit minimum high temperature flame retardant loom APPARATUS WIRING PROVISION An apparatus wiring panel shall be installed on the officer side bulkhead below the dash which shall include eight 8 open circuits consisting of three 3 20 amp one 1 30 amp three 3 10 amp and one 1 15 amp circuit with relays and breakers with trigger wires which shall be routed to the rocker switch panel LOAD MANAGEMENT SYSTEM The apparatus shall be equipped with a Class 1 Total System Manager TSM for performing electrical load management The TSM shall have sixteen 16 programmable outputs to supply warning and load switching requirements Outputs one 1 through twelve 12 shall be independently programmable to activate during the scene mode the response mode or both These outputs can also be programmed to activate with the ignition or master warning switch or to sequence and shed along with the priority Output thirteen 13 shall be designated to activate a fast idle syst
29. applicable 13 Air Compressor System Lubricant 14 Generator System Lubricant 15 Front tire cold pressure 16 Rear tire cold pressue 17 Maximum tire speed ratings OMNOORWN OCCUPANCY LABEL A permanent plate or label stating the maximum number of personnel allowed to ride on the apparatus at any one time shall be provided and installed in clear view of the driver SEATED AND BELTED LABEL Permanent plate or label shall be provided stating OCCUPANTS MUST BE SEATED AND BELTED WHEN APPARATUS IS IN MOTION and visible from each seated position DO NOT RIDE LABEL A permanent plate or label shall be attached to the appropriate areas of the apparatus stating that riding on the rear step or any exterior position on the apparatus is prohibited DO NOT WEAR HELMET LABEL Permanent plate or label shall be provided stating DO NOT WEAR HELMET WHILE SEATED and visible from each 43 seated position MAXIMUM TIRE SPEED LABEL A permanent plate or label shall be provided in the cab stating the maximum tire speed rating LENGTH HEIGHT WEIGHT LABEL A permanent plate or label shall be provided in the cab stating the overall length height and the gross vehicle weight rating GVWR in tons of the completed apparatus The wording on this label shall indicate that the information on the plate lable was current at the time of manufacture and if the overall height of the apparatus changes while the vehicle is in service the pur
30. at the bottom of the compartment to dispense the material The fuel fill shall be located behind the door WHEELWELL COMPARTMENT DOORS POLISHED STAINLESS Mirror finish polished stainless steel access doors shall be provided on all rear wheel well compartments WHEELWELL COMPARTMENT DOOR AJAR SYSTEM All wheel well compartments shall be connected into the door ajar system on the apparatus POLY TOOL BINS Five 5 poly tool bins shall be provided The bins shall have slotted handles on each end 10 x 22 Shipped loose with truck ROLL OUT TRAY There shall be two 2 roll out tray s provided The tray shall be constructed of 3 16 aluminum The tray shall have a 2 upward bent lip on all four sides of the tray Grant or equal 250 Ib total capacity heavy duty ball bearing type telescoping slides shall be provided A positive latching mechanism shall be provided to hold the tray in either the fully open or fully closed position over the wheel compartments to be used like rollout drawers 29 FOLDING ACCESS STEPS chrome plated folding access steps shall be provided in areas listed in these specifications All access steps provided on the apparatus shall support a minimum static load of 500 Ibs and be mounted in accordance to recommended mounting procedures as outlined by NFPA 1901 The steps shall be minimum of 6 5 wide x 6 5 depth The steps shall be attached to the apparatus using stainless steel bolts with lockin
31. axle SIDE AND INTERSECTOR WARNING SWITCH The side and intersector warning lights shall be controlled by a rocker switch on the switch panel This switch shall be clearly labeled for identification LIGHTBAR PROVISION The light bar s installed at the front of the cab roof shall be provided and installed by Spartan Chassis The light bar installation shall include mounting and wiring to a control switch on the cab dash CAB FRONT LIGHTBAR The lightbar provisions shall be for one 1 Whelen brand Freedom FN72QLED lightbar mounted centered on the front of the cab roof The lightbar shall be 72 00 inches in length The lightbar shall feature twelve 12 red LED lights and two 2 clear LED lights The clear lights shall be disabled with park brake engaged The cable shall exit the lightbar on the right side of the cab LIGHTBAR SWITCH The light bar shall be controlled by a rocker switch located on the switch panel This switch shall be clearly labeled for identification INTERIOR DOOR OPEN WARNING LIGHTS The interior of each door shall include one 1 red 4 00 inch diameter Truck Lite LED warning light located on the door panel Each light shall activate with a flashing pattern when the door is in the open position to serve as a warning to oncoming traffic SIREN CONTROL HEAD A Whelen 295HFS2 200 watt hands free remote siren amplifier control head shall be provided and flush mounted in the switch panel with a
32. be located on the front bumper face on the right side outboard of the frame rail in the far outboard position FRONT BUMPER TOW EYES The bumper shall include two 2 chrome plated tow eyes shall be installed through the front bumper The eyes shall be fabricated from 0 75 inch thick 1020 ASTM A36 hot rolled steel The inside diameter of the eye shall be 2 00 inches and include a chamfered edge CAB TILT SYSTEM The entire cab shall be capable of tilting approximately 45 degrees to allow for easy maintenance of the engine and transmission The electric over hydraulic lift system shall include an ignition interlock and red cab lock down indicator lamp on the tilt control which shall illuminate when holding the Down button to indicate safe road operation It shall be necessary to activate the master battery switch and set the parking brake in order to tilt the cab As a third precaution the ignition switch must be turned off to complete the cab tilt interlock safety circuit Two 2 spring loaded hydraulic hold down hooks located outboard of the frame shall be installed to hold the cab securely to the frame Once the hold down hooks are set in place it shall take the application of pressure from the hydraulic cab tilt lift pump to release the hooks Two 2 cab tilt cylinders shall be provided with velocity fuses in each cylinder port The cab tilt pivots shall be 1 90 inch ball and be anchored to frame brackets with 1 25 inch dia
33. be mounted within easy access via a hinged panel behind the right hand side headlight module The air intake system shall include a restriction indicator light in the warning light cluster on the instrument panel which shall activate when the air cleaner element requires replacement ENGINE EXHAUST SYSTEM The exhaust system shall include a diesel particulate filter and a diesel oxidation catalyst to meet current EPA standards The system shall utilize 0 065 inch thick stainless steel exhaust tubing between the engine turbo and the diesel particulate filter This section of the exhaust system shall be wrapped with a thermal cover in order to retain the necessary heat for system regeneration Zero leak clamps seal all system joints between the turbo and diesel particulate filter From the diesel particulate filter to the end of the tailpipe the system shall be plumbed with 0 065 inch thick aluminized steel tubing connected with overlapping band style clamps The discharge shall terminate horizontally on the officer side of the vehicle ahead of the rear tires The exhaust system shall be mounted below the frame in the outboard position providing maximum space for frame mounted components such as midship pumps ENGINE EXHAUST ACCESSORIES An exhaust temperature mitigation device shall be shipped loose for installation by the body manufacturer on the vehicle The temperature mitigation device shall lower the temperature of the exhaust by comb
34. be provided on the control console that electrically engages disengages the power take off HYDRAULIC GENERATOR MOUNTING The generator shall be mounted with adequate ventilation to prevent overheat The generator shall be mounted in the forward area of the hosebed properly protected A front hosebed bulkhead shall also be provided GROUNDING Grounding shall be in accordance with Section 250 6 Portable and Vehicle Mounted Generators of the NEC Ungrounded systems shall not be used Only stranded or braided copper conductors shall be used for grounding and bonding An equipment grounding means shall be provided in accordance with Section 250 91 Grounding Conductor Material of the NEC The grounded current carrying conductor neutral shall be insulated from the equipment grounding conductors and from the equipment enclosures and other grounded parts The neutral conductor shall be colored white or gray in accordance with Section 200 6 Means of Identifying Grounding Conductors of the NEC In addition to the bonding required for the low voltage return current each body and driving or crew compartment enclosure shall be bonded to the vehicle frame by a copper conductor This conductor shall have a minimum amperage rating of 115 percent of the nameplate current rating of the source specification label as defined in Section 310 15 amp capacities of the NEC A single conductor properly sized to meet the low voltage and line voltage requirements sh
35. clearly state PUMP COOLER 2 TANK REFILL RECIRCULATION DISCHARGE A 2 tank refill and pump recirculation line shall be provided from the discharge side of the pump into the tank The control for the discharge shall be on the pump operators panel The discharge shall be attached to the tank using flexible hose The water tank fill gauge shall be directly in line with this discharge control TANK REFILL VALVE AARON MANUAL CONTROL An Akron 8600 series discharge valve shall be utilized on tank refill line The valve shall be manually controlled from the pump operator s position STAINLESS STEEL PIPING All piping for discharges shall be stainless steel using stainless steel fittings Victaulic couplings shall be used in all front rear and side discharges deck pipes and cross lay hose beds for quick simple removal of any pipe section or valve for maintenance High pressure flexible helix wire reinforced piping with a minimum burst pressure of 1200 PSI may be used in some areas to minimize friction losses All flexible piping couplings shall be high tensile strength stainless steel All piping shall be properly supported and braced to prevent movement of piping other than what is allowed by the Victaulic couplings to compensate for apparatus flexing Any discharge manifolds provided on the apparatus must be fabricated of minimum Schedule 10 304 marine grade piping minimum of 4 in diameter The manifold must be fabricated and warra
36. does not have permanently mounted equipment RIGHT SIDE COFFIN COMPARTMENTS Coffin compartments shall be provided above the side compartments on the right side The length of the compartments shall be the same as the length of the side compartments The width shall be the same as the upper depth of the side access compartments Maximum depth will be provided based on design of the apparatus Two aluminum treadbrite access doors shall be provided for access The doors shall have a 1 raised lip to keep water from running into the compartment The doors shall be fully weatherstripped and shall have dual flush mounted latches A single light shall be provided and located under the door jamb between the two access doors Floor tiles shall be provided on the floor of the compartment in any area that does not have permanently mounted equipment 18 REAR TAILBOARD STEP A_18 depth x 66 width rear tailboard step shall be provided on the apparatus between the side compartments The step shall be spaced from the rear face of the apparatus body a minimum of 3 4 for easy wash out 24 RECESSED STEP BODY DESIGN The rear step of the apparatus shall be recessed into the rear of the body to provide addtional side compartmentation A flatback or beavertail fin design is not acceptable REAR STEP MATERIAL NFPA ALUMINUM TREADBRITE The rear step shall be constructed of NFPA complaint bright finish aluminum treadbrite RUBRAILS BRITE ANNODIZED
37. each accident Bodily Injury by Disease 500 000 policy limit Bodily Injury by Disease 100 000 each employee NOTE WC coverage may be waived if the contractor is the sole proprietor only with no employees and can provide the City of Athens with an APPROVED I 5 form from the Department of Labor Comprehensive General Liability Insurance a 700 000 limit of liability per occurrence for bodily injury and property damage b Comprehensive form covering all owned non owned and hired vehicles Auto Liability Insurance a 1 000 000 limit of liability per occurrence for bodily injury and property damage b Comprehensive form covering all owned non owned and hired vehicles City of Athens and any applicable Authority should be shown as an additional insured on General Liability Auto Liability and Umbrella Liability policies The cancellation provision should provide 30 days notice of cancellation Certificate Holder should read City of Athens 815 N Jackson Street Athens TN 37303 Insurance company must have an A M Best Rating of A 6 or higher Insurance company must be licensed to do business by the Tennessee Secretary of State Insurance company must be authorized to do business in Tennessee by the Tennessee Insurance Department REVISED 01 28 09 FROM NAME ADDRESS OF BIDDER TO BE OPENED DATE TIME BID RFQ NO PROJECT CONTRACTOR S REQUIREMENTS NAME LICENSE NO EXPIRA
38. fluids Common trade names for this material are Imperial 1200 and Durawear SEAT COLOR All seats supplied with the chassis shall be gray in color All seats shall include red seat belts SEAT BACK LOGO The seat back shall include a black and gray diamond logo which features a capital S in red located in the middle of the diamond The logo shall be centered on the standard headrest of the seat back and on the left side of a split headrest SEAT DRIVER The driver s seat shall be a Seats Inc 911 Universal series The four way seat shall feature 3 00 inch vertical travel air suspension and manual fore and aft adjustment with 6 00 inches of travel The suspension control shall be located on the seat below the left front corner of the bottom cushion The bottom seat cushion shall include an adjustment for rake angle offering added comfort The seat position shall include a three point shoulder harness with lap belt and an automatic retractor attached to the cab The buckle portion of the seat belt shall be mounted on a semi rigid stalk extending from the seat base within easy reach of the occupant The minimum vertical dimension from the seat H point to the ceiling for this belted seating position shall be 37 00 inches measured with the seat suspension height adjusted to the upper limit of its travel This model of seat shall have successfully completed the static load tests set forth by FMVSS 207 210 This testing shall include a si
39. frame Any proposals not including additional reinforcement for each cross member shall not be considered All relief areas shall be cut in with a minimum 2 00 inch radius at intersection points with the edges ground to a smooth finish to prevent a stress concentration point The frame and cross members shall carry a lifetime warranty to the original purchaser A copy of the frame warranty shall be made available upon request Proposals offering warranties for frames not including cross members shall not be considered FRAME WARRANTY The frame and cross members shall carry a limited lifetime warranty to the original purchaser The warranty shall include conditional items listed in the detailed warranty document which shall be provided upon request FRAME CLEAR AREA The chassis frame shall be left clear of chassis mounted components inside or outside the frame rails within the first 30 00 inches behind the cab to allow space for OEM installed components Cross members may be installed in the clear area if required for proper frame or driveline configuration FRAME PAINT The frame shall be powder coated black prior to any attachment of components All powder coatings primers and paint shall be compatible with all metals pretreatments and primers used The cross hatch adhesion test per ASTM D3359 shall not have a fail of more than ten 10 squares The pencil hardness test per ASTM D3363 shall have a final post curved pencil h
40. in the attached Specifications No 12 38 Note Late bids will not be considered under any circumstances Bids will be accepted if the date time stamped by the Purchasing Department is 2 30 p m date time stamps of 2 31 or later will be rejected Price shall include complete unit delivered to the City of Athens Municipal building located at 815 North Jackson St Athens Tennessee 37303 PARTS MANUAL Bidder shall furnish complete parts service amp repair manual s to be included as a part of the bid with no additional cost to the owner Paper or DVD form is acceptable BID AMOUNT 1 Total Bid amount for the Fire Engine in accordance with Specifications No 12 38 2 Is this a Demo Fire Engine A a ea ea 3 What Discounts are available for full prepayment of the vehicle amount or percentage of total cost 4 What is the timeline from payment to delivery of the apparatus 5 If this is a Demo will this engine be ready two weeks from payment Option 1 TRADE OPTION Asset 1389 1988 Emergency One fire Truck VIN IF9BBAA86J1037548 This unit may be inspected at the City Hall Fire Station 1 815 N Jackson St Athens TN Monday through Friday at 3 00 p m For an appointment the contact number is 423 744 2760 LESS TRADE IN NET PRICE WITH TRADE IN ALL BIDS MUST BE SEALED PROPERLY IDENTIFIED AND RETURNED WITH THE BID RETURN ADDRESS SHEET INCLUDED IN THIS BID PACKAGE TAPED TO THE OUTSIDE FRONT OF TH
41. or surface debris which may hinder the paint adhesion Once the surface is machine ground a high quality acid etching of base primer shall be applied Upon the application of body fillers and their preparation the cab shall be primed with a coating designed for corrosion resistance and surface paint adhesion The maximum thickness of the primer coat shall be 2 00 mils The entire cab shall then be coated with an intermediate solid or epoxy surfacing agent that is designed to fill any minor surface defects provide an adhesive bond between the primer and the paint and improve the color and gloss retention of the color The finish to this procedure shall be a sanding of the cab with 360 grit paper the seams shall be sealed with SEM brand seam sealer and painted with two 2 to four 4 coats of an acrylic urethane type system designed to retain color and resist acid rain and most atmospheric chemicals found on the fire ground or emergency scene The cab shall then be painted with the upper and lower colors specifically designated by the customer with a minimum thickness of two 2 00 mils of paint followed by a clear top coat not to exceed 2 00 mils CAB PAINT MANUFACTURER The cab shall be painted with PPG Industries paint CAB PAINT PRIMARY LOWER COLOR The lower paint color shall be PPG FBCH 71528 Red CAB PAINT SECONDARY UPPER COLOR The secondary upper paint color shall be PPG FBCH 2185 white CAB PAINT EXTERIOR BREAKLINE
42. outer fenderette 3 50 inches wide made of 12 gauge polished aluminum MUD FLAPS FRONT The front wheel wells shall have mud flaps installed on them CAB EXTERIOR FRONT amp SIDE EMBLEMS The cab shall include three 3 Spartan emblems There shall be one 1 installed on the front air intake grille and one 1 installed on each side of the cab exterior above the wheel well CAB EXTERIOR MODEL NAMEPLATE The cab shall include custom Metro Star nameplates on the front driver and officer side doors IGNITION A master battery system with a keyless start ignition system shall be provided Each system shall be controlled by a 1 4 turn Cole Hersee switch both of which shall be mounted to the left of the steering wheel on the dash A chrome push type starter button shall be provided adjacent to the master battery and ignition switches Each switch shall illuminate a green LED indicator light on the dash when the respective switch is placed in the ON position The starter button shall only operate when both the master battery and ignition switches are in the ON position BATTERY The single start electrical system shall include 6 Harris BCI 31 950 CCA batteries with a 210 minute reserve capacity and 4 0 welding type dual path starter cables per SAE J541 The cables shall have encapsulated ends with heat shrink and sealant BATTERY TRAY The batteries shall be installed within two 2 steel battery trays lo
43. properly wired to circuit panel with individual breaker The lighthead shall be a 1000 watt 120 volt AC and shall draw a maximum of 8 3 amps creating 22 000 lumens The light s shall be electrically tested so that they are safe for their intended use The light s shall be certified by Underwriters Laboratories UL and shall meet exceed NFPA 1901 Passenger rear of body NEMA L5 20R 20 AMP TWIST LOCK RECEPTACLE S There shall be four 4 NEMA type L5 20R_ 20 amp twist lock receptacles provided Wet Location All wet location receptacle outlets shall be of the grounding type with a wet location cover and installed in accordance with Section 210 7 Receptacles and Cord Connections of the NEC All wet location receptacles shall be installed not less than 24 from the ground Receptacles on off road vehicles shall be a minimum of 30 from the ground The face of any wet location receptacles shall be installed in a plane from vertical to not more than 45 degrees off vertical No receptacle shall be installed in a face up position Dry Location All receptacles located in a dry location shall be of the grounding type Receptacles shall not be less than 30 inches above the interior floor height Receptacle Wiring All wiring for both wet and dry locations shall be routed through liquid tight flexible conduit rated at not less than 194 degrees Each receptacle shall be wired to the panel board which shall haveseparate breakers for each receptacle
44. provided on the right side of the pump compartment The doors shall have pneumatic hold open devices and push button type flush latches The door shall be a minimum of 35 wide x 20 high 13 SIDE MOUNT BRUSHED STAINLESS STEEL PUMP PANEL All controls and instruments shall be located on the left side of the apparatus All discharge and intake valve controls shall be located on the left side pump panel BRUSHED STAINLESS STEEL PUMP PANELS The left and right side pump panels shall be constructed of 304 2B marine grade brushed stainless steel with a 4 brushed and polished finish The panels shall be held into place with two latches on the top to allow for easy removal of the panels The upper section of the left side pump panel shall be constructed of the same 304 2B marine grade stainless steel The upper section shall be vertically hinged and have a chrome plated latch to secure the panel when closed SIDE MOUNT PUMP PANEL LIGHTS L E D The side mount pump panel shall be illuminated using a 36 I L I track type L E D light assembly The light shall be constructed of an unbreakable type clear poly type flexible material housed in an aluminum extrusion mounted behind a brushed stainless steel light shield provided across the top of the gauge panel RIGHT SIDE DISCHARGE INTAKE PANEL LIGHTS L E D The right side discharge and intake panels shall be illuminated using a 24 I L I track type L E D light assembly The light shall be
45. purposes WARRANTY The chassis manufacturer shall provide a limited parts and labor warranty to the original purchaser of the custom built cab and chassis for a period of twelve 12 months or the first 24 000 miles whichever occurs first The warranty period shall commence on the date the vehicle is delivered to the end user The warranty shall include conditional items listed in the detailed warranty document which shall be provided upon request OPERATION MANUAL There shall be one 1 printed hard copy of the chassis operation manual provided with the chassis The manual shall include a parts list specific to the chassis model ENGINE AND TRANSMISSION OPERATION MANUALS There shall be two 2 printed hard copy sets of the engine operation manual and two 2 printed hard copy sets of the transmission operation manual specific to the model ordered included with the chassis in the ship loose items ENGINE SERVICE MANUALS There shall be two 2 printed hard copy sets of Cummins ISC ISL engine service reference manuals which shall be provided with the chassis TRANSMISSION SERVICE MANUALS There shall be two 2 printed hard copy sets of Allison 3000 transmission service manuals included with the chassis AS BUILT WIRING DIAGRAMS The cab and chassis shall include one 1 complete hard copy set of wiring schematics and option wiring diagrams CUSTOMER INSPECTION There shall be a customer inspection of the
46. receive engine and transmission information over the J1939 data bus to reduce redundant sensors The instrument panel shall contain the following gauges One 1 electronic tachometer shall be included The scale on the tachometer shall read from 0 to 3000 RPM One 1 electronic speedometer with an integral LCD odometer trip odometer and hour meter shall be included The speedometer shall have a dual scale with miles per hour MPH as the dominant scale and kilometers per hour KPH on the minor scale The speedometer scale shall read from 0 to 90 MPH 0 to 140 KPH The odometer shall display up to 9 999 999 9 miles The trip odometer shall display up to 9 999 9 miles The LCD screen shall also be capable of displaying certain diagnostic functions The hour meter shall display engine hours of operation One 1 three function gauge with primary system secondary system and fuel level shall be included The scale on the air pressure gauges shall read from 0 to 140 pounds per square inch PSI The air pressure scales shall be non linear to expand the scales in the region of normal operation A red indictor light in the gauge shall indicate a low air pressure The scale on the fuel level gauge shall read from empty to full A yellow indicator light shall indicate low fuel at the quarter tank level One 1 four function gauge with engine oil pressure coolant temperature transmission oil temperature and a voltmeter shall be included The scale
47. shall be manually controlled from the pump operator s position There shall be two 2 2 swivel elbows with 1 1 2 Male NST hose thread connections provided on the 1 3 4 cross lay hose beds The swivels shall be mounted in a position to prevent hose pinching at the hose thread connection There shall be one 1 2 1 2 swivel elbow with a 2 1 2 Male NST hose thread connection provided on the 2 1 2 cross lay hose bed The swivel shall be mounted in a position to prevent hose pinching at the hose thread connection AUTOMATIC CROSSLAY DRAIN VALVES 3 4 automatic drain valves shall be provided for all crosslays The valves shall have an all brass body with heavy duty neoprene seal The valve shall be normally open and shall close at 6psi using an all brass check assembly with stainless steel spring CROSSLAY COMPARTMENT ENDS The crosslay compartment shall be enclosed on each end using a heavy duty webbing to prevent hose from accidently unloading A nozzle strap shall be provided for each crosslay The strap shall be designed to loop through the nozzle handle and secured to the apparatus to keep nozzle from coming out of the crossaly compartment without manually disconnecting the nozzle strap 11 HINGED ALUMINUM TREADBRITE CROSSLAY COVER over the crosslay compartment The cover shall have a full length polished stainless steel hinge A chrome plated lift handle shall be provided on each end of the cover Rubber protection blocks shal
48. shall be mounted in the cab viewable through the cab mid side window behind the left front door ELECTRICAL INLET A Kussmaul 20 amp super auto eject electrical receptacle shall be supplied It shall automatically eject the plug when the starter button is depressed A single item or an addition of multiple items must not exceed the rating of the electric inlet that it s connected to Amp Draw Reference List Kussmaul 1000 Charger 3 5 Amps Kussmaul 1200 Charger 10 Amps Kussmaul 35 10 Charger 10 Amps 1000W Engine Heater 8 33 Amps 1500W Engine Heater 12 5 Amps 120V Air Compressor 4 2 Amps ELECTRICAL INLET LOCATION An electrical inlet shall be installed on the left hand side of cab over the wheel well ELECTRICAL INLET CONNECTION The electrical inlet shall be connected to the battery conditioner ELECTRICAL INLET COLOR The Kussmaul electrical inlet connection shall include a yellow cover HEADLIGHTS The cab front shall include four 4 rectangular halogen headlamps with separate high and low beams mounted in bright chrome bezels The headlamps shall be equipped with the Daytime Running light feature which shall illuminate the headlights to 80 brilliance when the ignition switch is in the On position and the parking brake is released FRONT TURN SIGNALS The front fascia shall include two 2 Whelen model 600 4 00 inch X 6 00 inch LED programmable amber turn signals which shall be insta
49. smooth appearance and perfect fit along each side of the cab Each door hinge shall be piano style with a 0 38 inch pin and shall be constructed of stainless steel CAB ENTRY DOOR TYPE All cab entry doors shall be full length in design to fully enclose the lower cab steps LH EXTERIOR REAR COMPARTMENT The cab shall offer an exterior compartment on the left side of the cab behind the rear door The compartment opening shall be 16 00 inches wide X 83 34 inches high The compartment size shall be 17 34 inches wide X 87 00 inches high X 21 19 inches deep below the floor The compartment shall be 18 50 inches wide X 66 00 inches high and full depth above the floor The forward facing wall of the compartment shall include the complete rear wall structure to allow seat frames to be mounted forward of the compartment The compartment shall have a 16 63 inch wide X 84 00 inch high X 1 50 inch thick hinged box pan style flush mount door with a bright aluminum tread plate inner panel and a bent D ring slam latch The door shall open towards the rear of the cab There shall be a switch to activate a light inside the compartment and the open compartment warning light in the cab in the event the door is left ajar LEFT HAND EXTERIOR REAR COMPARTMENT LIGHTING There shall be one 1 SoundOff Signal brand LED strip light installed to illuminate the exterior rear compartment on the left side of the cab The strip light shall be 43 00 inches long and sh
50. tank shall have a LIFETIME warranty provided by United Plastic Fabricating Inc The tank shall be constructed of 1 2 thick PT2E polypropylene sheet stock This material shall be non corrosive stress relieved thermo plastic natural in color and U V stabilized for maximum protection The booster tank shall be of a specific configuration and is so designed to be completely independent of the body and compartments All joints and seams shall be nitrogen welded and and tested for maximum strength and integrity The top of the booster tank is fitted with removable lifting eyes designed with a 3 to 1 safety factor to facilitate easy removal The transverse swash partitions shall be manufactured of 3 8 PT2E polypropylene material The longitudinal swash partitions shall be constructed of 3 8 PT2E polypropylene and extend through the cover to allow for positive welding and maximum integrity All partitions shall be equipped with vent and air holes to permit movement of air and water between compartments The partitions shall be designed to provide maximum water flow All swash partitions shall interlock with one another and are welded to each other as well as to the walls of the tank The tank cover shall be constructed of 1 2 thick PT2E polypropylene natural in color stress relieved UV stabilized material and shall incorporate a three piece locking design which will allow for individual removal of each section of necessary The tank cover shall be recess
51. the customer NO EXCEPTIONS HYPER FLEX BODY MOUNTING The body module assembly shall be mounted to the chassis frame rails with Hyper Flex vibration and shock isolators using a forward mounting system Flexible neoprene pads or U springs especially deve loped for the expected weight and torsional flexing of the apparatus body shall be incorporated into the system to eliminate chassis framerail flexing from transmitting harmful loads and twisting into the body STAINLESS STEEL APPARATUS BODY CONSTRUCTION The entire apparatus body shall be formed by shearing and bending fire apparatus quality stainless steel sheet metal Metal tubular structures or extrusions shall not be used in the construction of the apparatus body All edges of the sheared metal shall be sanded to remove any sharp shear edges prior to bending the met al After shearing and bending the body shall be assembled on a jig table that is designed to hold all apparatus body parts securely in place to insure an accurately built apparatus body After the fabricated body parts are secured on the jig the body shall be welded together using a wire weld er to insure proper weld penetration The entire apparatus body shall be welded together using only unexposed welding methods No welds shall be visible on the exterior of the apparatus body All welds on the exterior of the body shall be ground flush and filled with automotive body filler Metal or rubber trims shall not be used to hide weld
52. the frame Apparatus refers to total combined value for cab and chassis and OEM inputs Specification MODEL The chassis shall be a Metro Star model The cab and chassis shall include design considerations for multiple emergency vehicle applications rapid transit and maneuverability The chassis shall be manufactured for heavy duty service with the strength and capacity to support a fully laden apparatus one hundred 100 percent of the time MODEL YEAR The chassis shall have a vehicle identification number that reflects a 2011 model year COUNTRY OF SERVICE The chassis shall be put in service in the country of United States of America USA The chassis will meet applicable U S A federal motor vehicle safety standards per CFR Title 49 Chapter V Part 571 as clarified in the incomplete vehicle book per CFR Title 49 Chapter V Part 568 Section 4 which accompanies each chassis Spartan Chassis is not responsible for compliance to state regional or local regulations Dealers should identify those regulations and order any necessary optional equipment from Spartan Chassis or their OEM needed to be in compliance with those regulations APPARATUS TYPE The apparatus shall be a pumper vehicle designed for emergency service use which shall be equipped with a permanently mounted fire pump which has a minimum rated capacity of 750 gallons per minute 3000 L min The apparatus shall include a water tank and hose body whose primary purp
53. to a superior smooth surface 6 Cleaning After sanding in step 5 all surfaces shall be chemically cleaned again using PPG DX436 was and grease remover to remove all oil and dirt The surface to be painted shall be clean of all oil grease and dirt to ensure proper adhesion as per SSPC SP1 7 Primer Sealer Application PPG Delfleet F3985 F3986 F3987 two component urethane primer sealer shall be applied over the thoroughly sanded and cleaned primer surfacer as per bulletin DFT 054 8 Topcoat Application Two coats of PPG Delfleet FBCH basecoat color two component polyurethane paint shall be applied to the primer sealer as per bulletin DFT 001 The base color shall be followed by two coats of PPG Delfleet F3905 two component polyurethane clearcoat finish as per bulletin DFT 055 DRY FILM TESTS The apparatus manufacturer shall perform dry film readings on the painted apparatus to insure adequate paint thickness The total dry film readings shall be a minimum of 6 4 mils average These readings must be measured with an ETG ferrous nonferrous digital dry film thickness measurement instrument Readings must be taken from a minimum of 12 separate locations on the apparatus body The apparatus manufacturer must record these tests and make them available to the purchaser upon request PAINT PROCESS SYSTEM AUDIT The apparatus manufacturer shall strictly follow the documented paint application procedure as provided by the paint manufacturer The pai
54. to be live with the battery master switch AUXILIARY POWER POINT ENGINE TUNNEL The cab interior shall include two 2 12 volt cigarette lighter type receptacles to provide power sources for 12 volt electrical equipment The receptacles shall be connected directly to the batteries The receptacles shall be located on the top of the engine tunnel near the rear one 1 at the left corner and one 1 at the right corner STEP TRIM Each cab entry door shall include a three step entry The first step closest to the ground shall be constructed of polished 5032 H32 aluminum Grip Strut grating with angled outer corners The step shall feature a splash guard to reduce water and debris from splashing in to the step The splash guard shall have an opening on the outer edge to allow debris and water to flow through rather than becoming trapped within the stepping surface The lower step shall be mounted to a frame which is integral with the construction of the cab for rigidity and strength The middle step shall be integral with the cab construction and shall be trimmed with a Flex Tred adhesive grit surface material INTERIOR DOOR TRIM The doors of the cab shall include an aluminum plate the same weight and grade as the cab on the interior of the door The aluminum shall be then painted DOOR TRIM CUSTOMER NAMEPLATE The interior door trim on the front doors shall include a customer nameplate which states the vehicle was custom built for
55. to the ceiling for each belted seating position shall be 35 00 inches This model of seat shall have successfully completed the static load tests by FMVSS 207 210 This testing shall include a simultaneous forward load of 3000 pounds each on the lap and shoulder belts and twenty 20 times the weight through the center of gravity This model of seat installed in the cab model as specified shall have successfully completed the dynamic sled testing using FMVSS 208 as a guide with the following accommodations In order to reflect the larger size outfitted firefighters the test dummy used shall be a 95th percentile hybrid III male weighing 225 pounds rather than the 50th percentile male dummy weighing 165 pounds as referenced in FMVSS 208 The model of seats shall also have successfully completed the flammability of materials used in the occupant compartments of motor vehicles as outlined in FMVSS 302 of which decides the burning rate of materials in the occupant compartments of motor vehicles SEAT BACK FORWARD FACING CENTER The forward facing center seat backs shall include a Ziamatic brand Rol Loc mechanical self contained breathing apparatus SCBA bracket The Positive Locking Mechanical walk away bracket shall meet NFPA 1901 03 9G dynamic requirements for cylinder restraint systems for use in crew compartments of fire truck cabs The bracket shall be third Party tested to ten 10 times the force of gravity The bracket shall secure a se
56. 00 RPM and shall be governed at 2200 RPM The torque rating shall feature 1200 foot pounds of torque at 1300 RPM with 543 cubic inches of displacement The Cummins ISL 425 engine shall feature an electronic governor A wiring harness shall be supplied ending at the back of the cab The harness shall include a connector which shall allow an optional harness for the pump panel The included circuits shall be provided for a tachometer oil pressure engine temperature hand throttle high idle and a PSG system A circuit for J1939 data link shall also be provided at the back of the cab The engine shall include an engine mounted combination full flow by pass oil filter with replaceable spin on cartridge for use with the engine lubrication system The engine shall include Citgo brand Citgard 500 or equivalent SAE 15W40 CJ4 low ash engine oil which shall be utilized for proper engine lubrication CAB ENGINE TUNNEL The cab interior shall include an integrated engine tunnel constructed of 5052 H32 Marine Grade 0 19 of an inch thick aluminum The tunnel shall be a maximum of 41 50 inches wide X 23 00 inches high DIESEL PARTICULATE FILTER CONTROLS There shall be two 2 controls for the diesel particulate filter One 1 control shall be for regeneration and one 1 control shall be for regeneration inhibit ENGINE PROGRAMMING HIGH IDLE SPEED The engine high idle control shall maintain the engine idle at approximately 1250 RPM when engaged
57. 003 5020PRT 025 5316A 001 5020PRT 025 5004 003 5020PRT 025 1314 005 Switches Right Pnl 8 4 4 RH Label Port Info Connected From m es ee ee ee ee ee 1314 005 5020PRT 001 1314 005 5020PRT 002 1314 005 5020PRT 003 1314 005 5020PRT 004 1314 005 5020PRT 005 1314 005 5020PRT 006 1314 005 5020PRT 007 1314 005 5020PRT 008 1313 004 Switches Left Pnl 8 6 2 Port Info Label Connected From ee ee es ee ees ees ee 2933 NN2 245 ENG AUX BRK HIGH LOW OFF 2933 NN2 020 HEADLT FLASHER 1313 004 5020PRT 003 2933 NN2 031 AIR HORN ELECTRIC 2933 NN2 141 MUD SNOW TRACTION HEADLIGHTS WIPER DIMMER 1708 005 5020PRT 025 5425 002 5020PRT 025 5514 002 5020PRT 025 3205 012 5020PRT 025 5350A 001 5020PRT 025 1511 001 5020PRT 025 5350B 001 5020PRT 025 Weight Distribution METI EEr 29 in Erra 27 in CA of Chassis me Calculated Calculated Front Axle Weight Rear Axle Weight Track Width Assum ptions 1 Full fluids and fuel Values shown are estim ates OEM is responsible for firal 2 250 Ib occupant mass per seating position analysis of weights and any data com m unicated to the end user 3 Does not include spare tires wheeb Calculated Apparatus Weight 18 654 lbs Calculated Apparatus Z CG 46 87 in Calculated Apparatus Y CG 2 02 in Note The Y CG value above is calculated from the top of
58. 200 engine RPMs The air compressor shall feature a higher delivery efficiency translating to more air delivery per horsepower absorbed The compressor shall include an aluminum cylinder head which shall improve cooling reduce weight and decrease carbon formation Superior piston and bore finishing technology shall reduce oil consumption and significantly increasing the system component life AIR GOVERNOR An air governor shall be provided to control the cut in and cut out pressures of the engine mounted air compressor The governor shall be calibrated to meet FMVSS requirements The air governor shall be located on the air cleaner bracket on the right frame rail behind the officer step MOISTURE EJECTORS An automatic moisture ejector with a manual drain provision shall be installed on the wet tank of the air supply system Manual pet cock type drain valves shall be installed on all remaining reservoirs of the air supply system AIR SUPPLY LINES A dual air system plumbed with color coded reinforced nylon tubing air lines shall be installed on the chassis The primary rear brake line shall be green the secondary front brake line red the parking brake line orange and the auxiliary outlet will be blue Brass compression type fittings shall be used on the nylon tubing All drop hoses shall include fiber reinforced neoprene covered hoses AIR HORN SHUTOFF VALVE A shut off valve located in the driver s dash shall be instal
59. 3 3349 002 3327 002 3326 002 3334 002 3338 001 2103 2040 2106 0470 2101 002 8007 005 2117 004 2110 004 2201 001 2202 006 2226 001 2221 002 5501 012 2216 004 2232 002 5504 029 2217 005 2204 006 2301 001 2305 001 1401 009 1402 002 1407 001 1419 008 1430 001 1412 008 1431 001 1410 003 1432 001 1409 003 1433 001 1614 022 1617 001 1603 003 1601 002 AIR GOVERNOR MOISTURE EJECTORS AIR SUPPLY LINES AIR HORN SHUTOFF VALVE AIR INLET CONNECTION AIR INLET LOCATION PLUMBING AIR INLET CONNECTION AIR INLET OUTLET FITTING TYPE AIR TANK SPACERS REAR AIR TANK MOUNTING WHEELBASE REAR OVERHANG FRAME FRAME WARRANTY FRAME CLEAR AREA FRAME PAINT FRONT BUMPER FRONT BUMPER EXTENSION LENGTH FRONT BUMPER EXTENSION FRAME WIDTH FRONT BUMPER WINCH AIR HORN AIR HORN LOCATION AIR HORN RESERVOIR ELECTRONIC SIREN SPEAKER ELECTRONIC SIREN SPEAKER LOCATION FRONT BUMPER TOW EYES CAB TILT SYSTEM CAB TILT CONTROL RECEPTACLE CAB WINDSHIELD GLASS FRONT DOOR GLASS TINT FRONT DOOR GLASS REAR DOOR RIGHT HAND GLASS TINT REAR DOOR RIGHT HAND GLASS REAR DOOR LEFT HAND GLASS TINT REAR DOOR LEFT HAND GLASS SIDE MID RIGHT HAND GLASS TINT SIDE MID RIGHT HAND GLASS SIDE MID LEFT HAND GLASS TINT SIDE MID LEFT HAND CLIMATE CONTROL CLIMATE CONTROL ACTIVATION A C CONDENSER LOCATION A C COMPRESSOR Air Governor Mnt on Air Cleaner Bracket Moisture Ejectors Manual Auto Wet Tank Air Sply Lines Nylon A
60. 321 001 1307 002 5040 007 5042 010 1303 017 1102 013 1323 001 1105 001 1308 001 1332 008 1345 002 1301 003 1318 003 1304 001 1335 003 1344 002 1312 006 1313 004 1314 005 1225 012 8101 002 1237 001 1243 001 1201 003 1213 015 1219 001 8102 003 1202 008 1214 026 1220 002 8103 002 1263 001 CAB INSULATION UNDER CAB INSULATION INTERIOR TRIM FLOOR INTERIOR TRIM REAR WALL INTERIOR TRIM HEADER TRIM INTERIOR TRIM SUNVISOR TRIM CENTER DASH TRIM LEFT HAND DASH TRIM RIGHT HAND DASH ENGINE TUNNEL TRIM POWER POINT DASH MOUNT AUXILIARY POWER POINT ENGINE TUNNEL STEP TRIM INTERIOR DOOR TRIM DOOR TRIM CUSTOMER NAMEPLATE CAB DOOR TRIM REFLECTIVE NTERIOR GRAB HANDLE A PILLAR NTERIOR GRAB HANDLE FRONT DOOR NTERIOR GRAB HANDLE REAR DOOR NTERIOR TRIM VINYL COLOR NTERIOR ABS TRIM COLOR NTERIOR FLOOR MAT COLOR CAB PAINT INTERIOR DOOR TRIM DASH PANEL GROUP SWITCHES CENTER PANEL SWITCHES LEFT PANEL SWITCHES RIGHT PANEL SEAT BELT WARNING OCCUPANCY ROLLOVER PROTECTION SEAT MATERIAL SEAT COLOR SEAT DRIVER SEAT BACK DRIVER SEAT MOUNTING DRIVER OCCUPANCY ROLLOVER PROTECTION DKIVEK SEAT OFFICER SEAT BACK OFFICER SEAT MOUNTING OFFICER OCCUPANCY ROLLOVER PROTECTION UP PICEK SEAT REAR FACING OUTER LOCATION I I I I I I Cab Insulation Under Cab Insulation Engine Tunnel Interior Trim Floor Interior Trim Vinyl Rear Wall Interior Trim Vinyl Header Trim ABS Interior Trim Sunvisor T
61. 5 seconds for the following situation Turn Signal Reminder turn signal left on for more than one 1 mile 1 Feature only available when optionally equipped 2 Feature only available on engines with pre heat capability 3 Feature only on vehicles with diesel particulate filter DPF 4 Warning light is present in gauge 5 A message in the LCD screen will also be displayed CAMERA An Audiovox Voyager heavy duty rearview camera system shall be supplied The system shall include one 1 box shaped camera shall be shipped loose for OEM installation in the body to afford the driver a clear view of the rear to the vehicle and one 1 teardrop shaped camera with a chrome plated plastic housing shall be mounted on the officer side of the cab below windshield ahead of the front door at approximately the same level as the cab door handle The cameras shall be wired to a 7 00 inch flip down monitor which shall include a color display and day and night brightness modes installed above the driver position The rear camera shall activate when the transmission is placed in reverse and the right camera shall activate with the right side turn signal The camera system shall include a one way communication device that shall be an integral part of the rear camera for the use of voice commands directly to the driver COMMUNICATION ANTENNA An antenna base for use with an NMO type antenna shall be mounted on the right hand front corner of th
62. 815 North Jackson Street P O Box 849 Athens Tennessee 37371 0849 www cityofathenstn com 423 744 2780 Fax 423 744 8866 mmarshall cityofathenstn com Matthew Marshall CITY OF ATHENS Purchasing Director NOTICE OF DEMO EXCEPTIONS The following exceptions will be allowed for the bidding procedure 1 No performance bond will be required if a demo vehicle is submitted 2 Delivery must be within 15 days of contract signing on all demo s 3 Mileage must be less than 15 000 thousand miles on demo units 4 All demo s must have a pre 2010 engine Bidder s company name signature and date indicate that these terms and conditions have been read understood and accepted DATE BIDDER S COMPANY NAME COMPANY REPRESENTATIVE Printed Name TELEPHONE EMAIL Written Signature FAX THIS DOCUMENT MUST BE SIGNED AND RETURNED WITH BID 815 North Jackson Street P O Box 849 Athens Tennessee 37371 0849 www cityofathenstn com Matthew Marshall Director of Purchasing 423 744 2780 Fax 423 744 8866 mmarshall cityofathenstn com CITY OF ATHENS REQUEST FOR BID NO 1561 The City of Athens will receive sealed bids at the Athens Municipal Building Purchasing Department located at 815 N Jackson Street Athens TN 37303 until 2 30 p m ET Wednesday April 25 2012 at which time and place bids will be publicly opened and read aloud for Fire Engine with Demo Option as described
63. CTRIC REWIND CORD REEL There shall be two 2 Hannay model ECR1616 17 18 electric rewind cord reel s provided and properly mounted Each reel shall be wired to the electrical panel board through flexible PVC conduit An individual breaker shall be provided at the panel for the reel 41 A momentary push button switch shall be provided mounted in close proximity to each reel for activating the electric rewind The switch shall be labeled CORD REEL REWIND A label shall be provided mounted in a readily visible area adjacent to the reel to indicate the following a Current rating b Current type Phase Voltage Total cable length c d e wa rower a CORD REEL MOUNTING LOCATION The cord reel shall be mounted in the compartment with access provided by opening the compartment doors Both in the D1 compartment 200 12 3 SEOW A ELECTRICAL CABLE A continuous 200 length of 12 3 SEOW A electrical cable shall be provided on the reel s The cable shall be rated at 600 volts at 194 degrees YELLOW ELECTRICAL CABLE The electrical cable on the cord reel s shall be yellow EXTENDA LITE LIGHTED GFI PROTECTED JUNCTION BOX S There shall be two 2 Extenda lite lighted junction box es provided and hardwired to the cable end s The cable shall have a strain relief where it enters the junction box The junction box shall have 3 individual L5 15 15 amp twist lock single receptacles and 1 household GFI protected 5
64. Center Occupancy Rollover Protection FFC RollTek Seat Frm Fwd Fcg Dual Seat Frm Fwd Feg Strg Acc Dr 2 R L Sd Cab Frt Undrst Strg Acc Panel Seat Compartment Door Finish Zolatone Onyx Black Windshield Wiper System Dual Motors Electronic Windshield Fluid Level Indicator Cab Door Hardware Chrome w Scuff Plate Door Locks Manual Door Lock LH Rear Cab Compartment Manual Door Lock RH Rear Cab Compartment Manual Grab Handles SS 18 Mirror Aerodynamic Retrac 613285 Rmt Htd Ltd Rearview Mirror Heat Sw Mirror Ctrl Pnl Cab Fender Alum Mud Flaps Frt Cab Ext Frt amp Side Emblems Cab Exterior Model Nameplate Metro Star Ign Mstr Sw w Keyless Start Batt 6 Group 31 Harris Batt Tray 2 R L Steel Batt Cables Batt Jumper Stud Frt LH Lwr Step Alternator Leece Neville 320A Batt Cond Kussmaul 1200 Batt Cond Display LH Mid Glass Elec Inlet 120V 20A Auto Eject Elec Inlet Location LH Cab Side Mid 5210 004 5206 002 5301 050 5303 004 5337 001 5336 003 5302 003 5350 001 5308 003 5309 002 5312 001 5306 002 5318 006 5316 003 5330 006 5332 003 5331 002 5305 001 5310 002 5315 002 5406 001 5422 001 5409 002 5425 002 5401 002 5413 003 5423 007 5404 002 5419 003 5420 002 5402 006 5418 003 5412 002 5424 008 5403 013 5450 004 5426 002 5407 003 5510 004 5514 002 ELECTRICAL INLET CONNECTION ELECTRICAL INLET COLOR HEADLIGHTS FRONT TURN SIGNALS HEADLIGHT LOCATION SIDE TURN MARKER LIGHTS MARKE
65. E ENVELOPE PACKAGE THAT YOU ARE RETURNING The City of Athens reserves the right to reject any and all bids or waive any informalities and to accept any proposal deemed to be in the best interest of the City Sign here COMPANY DATE BY Printed Signature PHONE FAX EMAIL Specifications for New or Demo Fire Engine 12 38 Part 1 Cab and Chassis Part 2 Fire Engine Box Part 1 0100 007 8012 019 8011 011 8001 001 8006 009 8008 001 0104 001 0101 003 0102 004 8010 002 1000 016 1501 002 1518 012 1521 002 1533 001 1522 080 1523 244 1524 002 1515 005 8013 014 1334 022 1005 001 1101 001 1540 143 5313 005 1548 005 1541 143 5345 005 1549 005 8004 007 9001 001 5000 001 5006 002 5004 003 5622 002 5031 001 5030 002 MODEL CUSTOMERS OEMS MODEL YEAR COUNTRY OF SERVICE APPARATUS TYPE VEHICLE TYPE AXLE CONFIGURATION GROSS AXLE WEIGHT RATINGS FRONT GROSS AXLE WEIGHT RATINGS REAR PUMP PROVISION CAB STYLE CAB FRONT FASCIA FRONT GRILLE CAB PAINT EXTERIOR CAB PAINT MANUFACTURER CAB PAINT PRIMARY LOWER COLOR CAB PAINT SECONDARY UPPER COLOR CAB PAINT EXTERIOR BREAKLINE CAB PAINT PINSTRIPE CAB PAINT WARRANTY CAB PAINT INTERIOR CAB ENTRY DOORS CAB ENTRY DOOR TYPE LH EXTERIOR REAR COMPARTMENT LH EXTERIOR REAR COMPARTMENT LIGHTING LH EXTERIOR COMPARTMENT INTERIOR FINISH RH EXTERIOR REAR COMPARTMENT RH EXTERIOR REAR COMPARTMENT LIGHTING RH EXTERIO
66. Model Waterous CSUC20 Midship Pump Ratio 2 27 1 3048 007 3010 1000 3109 021 3111 001 3104 003 3101 015 3102 007 2401 003 8059 007 2405 001 2502 002 2501 006 2601 001 2603 001 2609 002 2606 009 2610 003 2608 001 3401 003 3403 001 8061 004 3411 001 3408 004 3501 032 3601 014 3602 012 3413 538 3614 013 3701 016 3703 004 3702 002 3205 012 3206 001 3207 010 3208 001 3204 001 3213 001 3214 001 3202 001 3215 001 3210 015 3320 001 MIDSHIP PUMP GEARBOX DROP MIDSHIP PUMP LOCATION C L SUCTION FROM REAR AXLE FUEL FILTER WATER SEPARATOR FUEL LINES FUEL SHUTOFF VALVE FUEL TANK FUEL TANK FILL PORT FRONT AXLE FRONT AXLE WARRANTY FRONT WHEEL BEARING LUBRICATION FRONT SHOCK ABSORBERS FRONT SUSPENSION STEERING COLUMN WHEEL POWER STEERING PUMP ELECTRONIC POWER STEERING FLUID LEVEL INDICATOR FRONT AXLE CRAMP ANGLE POWER STEERING GEAR CHASSIS ALIGNMENT REAR AXLE REAR AXLE DIFFERENTIAL LUBRICATION REAR AXLE WARRANTY REAR WHEEL BEARING LUBRICATION VEHICLE TOP SPEED REAR SUSPENSION FRONT TIRE REAR TIRE REAR AXLE RATIO TIRE PRESSURE INDICATOR FRONT WHEEL REAR WHEEL WHEEL TRIM BRAKE SYSTEM FRONT BRAKES REAR BRAKES PARK BRAKE PARK BRAKE CONTROL FRONT BRAKE SLACK ADJUSTERS REAR BRAKE SLACK ADJUSTERS AIR DRYER FRONT BRAKE CHAMBERS REAR BRAKE CHAMBERS AIR COMPRESSOR Midship Pump Gearbox Drop Waterous C Midship Pump Location C L Suction 100 Fuel Filter Wtr Separa
67. NTING REAR FACING OUTER The rear facing outer seats shall offer special mounting positions which shall be 2 00 inches towards the rear wall offering additional space between the front seats and the outer rear facing seats OCCUPANCY ROLLOVER PROTECTION RFO The rear facing outboard seating position shall be equipped with the RollTek Rollover Occupant Protection System SEAT BELT ORIENTATION CREW The crew position seat belts shall follow the standard orientation which extends from the outboard shoulder extending to the inboard hip SEAT FORWARD FACING CENTER LOCATION The crew area shall include two 2 forward facing center crew seats with both located at the center of the rear wall SEAT CREW FORWARD FACING CENTER The crew area shall include a seat in the forward facing center position which shall be a Seats Inc 911 series The seat shall feature a tapered and padded seat and cushion The seat and cushion shall be hinged and compact in design for additional room and shall remain in the stored position until occupied The seat shall feature an all belts to seat ABTS style of safety restraint The ABTS feature shall include a three point shoulder harness with the lap belt and automatic retractor as an integral part of the seat assembly The buckle portion of the seat belt shall extend from the seat base towards the driver position within easy reach of the occupant The minimum vertical dimension from the seat H point
68. OR TRIM VINYL COLOR The cab interior vinyl trim surfaces shall be gray in color INTERIOR ABS TRIM COLOR The cab interior vacuum formed ABS composite trim surfaces shall be gray in color INTERIOR FLOOR MAT COLOR The cab interior floor mat shall be gray in color CAB PAINT INTERIOR DOOR TRIM The inner door panel surfaces shall be painted with Zolatone 20 71 onyx black texture finish DASH PANEL GROUP The main center dash area shall include three 3 removable panels located one 1 to the right of the driver position one 1 in the center of the dash and one 1 to the left of the officer position The center panel shall be within comfortable reach of both the driver and officer SWITCHES CENTER PANEL The center dash panel shall include eighteen 18 rocker switch positions in a twelve 12 over six 6 configuration in the left portion of the panel A rocker switch with a blank legend installed directly above shall be provided for any position without a switch and legend designated by a specific option The non specified switches shall be two position black switches with a green indicator light Each blank switch legend can be custom engraved by the body manufacturer All switch legends shall have red backlighting provided SWITCHES LEFT PANEL The left dash panel shall include eight 8 switches There shall be six 6 switches across the top of the panel and two 2 staggered on the left hand portion o
69. PLY WITH THE GUIDELINES POSTED IN SPARCON FOR THE ASSOCIATED DATABOOK DUE TO UNRESOLVED CLARIFICATIONS OR CONTENT CHANGES WILL BE CANCELED BY SPARTAN CHASSIS AND SUBJECTED TO A MINIMUM CANCELLATION FEE OF TEN THOUSAND DOLLARS 10 000 OR MORE BASED ON WHERE THE ORDER IS IN THE COMPONENT PROCUREMENT OR PRODUCTION PROCESS ANY OTHER WRITTEN OR VERBAL AGREEMENTS OR REPRESENTATIONS MADE REGARDING 2007 EPA EMISSION COMPLIANT ENGINES ARE SUPERSEDED BY THE PREVIOUS GOVERNING STATEMENTS REGARDING THE SALE AND AVAILABILITY OF 2007 FEDERAL EPA EMISSION COMPLIANT ENGINES BY SPARTAN CHASSIS The power plant for the vehicle shall offer a high pressure performance turbo charged engine which shall feature a high pressure common rail fuel system This system shall be coupled with a proven Holset turbo which delivers outstanding performance at ratings up to 425 HP The Cummins ISL engine shall include replaceable mid stop cylinder liners plus heavy duty roller followers targeted piston cooling and 30 more efficient oil cooling for improved durability and reliability The heavy duty design shall also feature stronger braking capacity The engine shall be EPA certified to meet the 2007 emissions standards without compromising performance reliability or durability The Cummins ISL 425 engine shall feature an air charge cooled engine which consists of an in line six 6 cylinder four cycle diesel powered engine The engine shall offer a rating of 425 horse power at 21
70. R amp ICC LIGHTS HEADLIGHT AND MARKER LIGHT ACTIVATION GROUND LIGHTS STEP LIGHTS ENGINE COMPARTMENT LIGHT SIDE SCENE LIGHTS SIDE SCENE LIGHT LOCATION SIDE SCENE ACTIVATION REAR SCENE LIGHTS REAR SCENE LIGHT LOCATION REAR SCENE LIGHT ACTIVATION INTERIOR OVERHEAD LIGHTS MAP LIGHTS SPOTLIGHT DO NOT MOVE APPARATUS LIGHT MASTER WARNING SWITCH HEADLIGHT FLASHER HEADLIGHT FLASHER SWITCH INBOARD FRONT WARNING LIGHTS INBOARD FRONT WARNING LIGHTS COLOR FRONT WARNING SWITCH INTERSECTION WARNING LIGHTS INTERSECTION WARNING LIGHTS COLOR INTERSECTION WARNING LIGHTS LOCATION SIDE WARNING LIGHTS SIDE WARNING LIGHTS COLOR SIDE WARNING LIGHTS LOCATION SIDE AND INTERSECTION WARNING SWITCH LIGHTBAR PROVISION CAB FRONT LIGHTBAR LIGHTBAR SWITCH INTERIOR DOOR OPEN WARNING LIGHTS SIREN CONTROL HEAD HORN BUTTON SELECTOR SWITCH Elec Inlet Conn to Batt Conditioner Elec Inlet Color Yellow Headlights DRL Frt Turn Signals Whelen 600 LED Headlights Below Frt Warn Lts Side Turn Marker Lts LED Marker amp ICC Lts Face Mnt LED Hdlt amp Mrkr Lt Actv Rkr Sw Ground Lts Resp Dr amp Prk Brk Sw Step Lts Engine Compartment Work Lt 1 Side Scene Lts Whelen 810 Series 12V QH Clear 32 Deg Side Scene Lt Loc Upper Mid Fwd 10 Roof Position Side Scene Actv Indv Sw Rear Scene Lts Whelen 810 12V QH Clear 32 Degree 2 Rr Scene Lt Loc 2 Outer Rr Wall Rear Scene Lt Actv Sgl Sw Interior Overhead Lights Map Lt Roxter RH
71. R COMPARTMENT INTERIOR FINISH CAB STRUCTURAL WARRANTY CAB TEST INFORMATION ELECTRICAL SYSTEM APPARATUS WIRING PROVISION LOAD MANAGEMENT SYSTEM DATA RECORDING SYSTEM POWER amp GROUND STUD AUXILIARY POWER amp GROUND STUD Description Metro Star Or similar Pumper or Similar Model Year 2011 Country of Service United States Of America Apparatus Type Pumper Vehicle Type Straight Truck Axle Configuration 4x2 Rear Axle Drive Only GAWR Front 20000 GAWR Rear 27000 Pump Provision Driveline Midship Cab Style ELFD 10 Raised Roof Cab Frt Fascia Classic Cab Frt Grille Classic Styled Cab Paint Exterior Two Tone Cab Paint Manufacturer PPG Cab Paint Primary Lower Color PPG Red FBCH 71528 Cab Paint Sec Upper Color PPG White FBCH 2185 Cab Paint Exterior Breakline Classic Cab Paint Pinstripe 1 2 Black Temporary Cab Paint Warranty 2011 10 Year 100 000 Miles Cab Paint Int Zolatone Onyx Blk Cab Entry Doors 4 Cab Entry Door Type Full Length LH Ext Rr Cmpt 66 H x 17 W w 84 Rev Hng Dr Fwd Rr Wall Structure LH Ext Rr Cmpt Lt LED Strip Lt SoundOff Signal 43 LH Exterior Compartment Interior Finish Zolatone Onyx Black RH Ext Rr Cmpt 66 H x 17 W w 84 Rev Hng Dr Fwd Rr Wall Structure RH Ext Rr Cmpt Lt LED Strip Lt SoundOff Signal 43 RH Exterior Compartment Interior Finish Zolatone Onyx Black Cab Structural Warranty 2011 10 Year 100 000 Miles Cab Test Information Crash Test ECE 29 Elec System 12V DC Apparat
72. RAIL A 12 NFPA compliant horizontal handrail shall be provided on on the right rear of the apparatus towards the rear of the hosebed LEFT REAR GRAB RAIL A 12 NFPA compliant horizontal handrail shall be provided on on the left rear of the apparatus towards the rear of the hosebed 48 INTERMEDIATE REAR HORIZONTAL HAND RAIL A 48 intermediate horizontal handrail shall be provided on the rear of the apparatus NFPA 1901 CERTIFIED 12 VOLT ELECTRICAL SYSTEM The 12 volt apparatus body electrical system shall be provided and shall be in compliance with NFPA 1901 testing and certification procedures as follows NFPA MINIMUM ELECTRICAL LOAD DEFINITION The NFPA 1901 defined minimum electrical load shall consist of the total amperage required to si multaneously operate the following in a stationary mode 1 Propulsion engine and transmission 2 The clearance and marker lights 3 Communication equipment 5 amp default 4 Illumination of all walking surfaces the ground at all egress points control and instrumentation panels and 50 of total compartment lighting 5 Minimum warning lights required for blocking right of way mode 6 The current to simultaneously operate and fire pump and all specified electrical devices 7 Anything defined by the purchaser in the advertised specifications to be critical to the mission of the apparatus 31 RESERVE CAPACITY TEST The first electrical test to be performed will be the Reserve Cap
73. RIOR FINISH The interior of the right hand exterior compartment shall have a Zolatone 20 71 onyx black texture finish CAB STRUCTURAL WARRANTY The cab structure shall be warranted for a period of ten 10 years or one hundred thousand 100 000 miles which ever may occur first Warranty conditions may apply and shall be listed in the detailed warranty document that shall be provided upon request CAB TEST INFORMATION The cab shall have successfully achieved survival of the International crash test ECE 29 Addendum 28 Revision as indicated below As part of the ECE regulation 29 test the frontal area of the cab is struck by a 3 700 pound pendulum weight The weight is brought back to a sixty degree angle and then the weight is released and allowed to swing forward imparting some 32 600 pounds foot of force to the cab front face The cab shall be so constructed that after the test there will be minimal intrusion of the cab structure into the passenger area The doors shall remain usable for both entry and exit Also as part of the test the cab roof must withstand a static load bearing test The cab shall withstand a weight of over 60 000 pounds without permanent damage or collapse The above tests shall be witnessed by and attested to by an independent third party The test results shall be recorded on by cameras high speed imagers accelerometers and strain gauges with notarized copies of the letters verifying the test results
74. TINT REAR DOOR LEFT HAND The window located in the left hand side rear door shall include a standard green automotive tint which shall allow seventy five percent 75 light transmittance GLASS SIDE MID RH The cab shall include a window on the officer s side behind the front and ahead of the crew doors which shall measure 16 00 inches wide X 26 00 inches high This window shall be fixed within this space and shall be rectangular in shape The window shall be mounted using self locking window rubber The glass utilized for this window shall include a green automotive tint unless otherwise noted GLASS TINT SIDE MID RIGHT HAND The window located on the right hand side of the cab between the front and rear doors shall include a standard green automotive tint which shall allow seventy five percent 75 light transmittance GLASS SIDE MID LH The cab shall include a window on the driver s side behind the front door and ahead of the crew door and above the wheel well which shall measure 16 00 inches wide X 26 00 inches high This window shall be fixed within this space and shall be rectangular in shape The window shall be mounted using self locking window rubber The glass utilized for this window shall include a green automotive tint unless otherwise noted GLASS TINT SIDE MID LEFT HAND The window located on the left hand side of the cab between the front and rear doors shall include a standard green automotive tint which s
75. TION DATE SUB REQUIREMENTS CLASSIFICATION NAME LICENSE NO EXPIRATION DATE CLASSIFICATION NAME LICENSE NO EXPIRATION DATE CLASSIFICATION NAME LICENSE NO EXPIRATION DATE CLASSIFICATION NAME LICENSE NO EXPIRATION DATE CLASSIFICATION ANY OTHER SUBS LIST ON SEPARATE PAPER AND ATTACH TO BACK OF ENVELOPE TO PURCHASING DIVISION CITY OF ATHENS 815 N Jackson Street P O Box 849 Athens TN 37371 0849 NOTICE TO BIDDERS When finalizing your bid proposal please use the following checklist to ensure that you have signed and included all necessary documents for your bid to be considered FAILURE TO INCLUDE ALL REQUESTED DOCUMENTS SHALL DISQUALIFY YOUR BID AND IT WILL NOT BE CONSIDERED Have you Ll Signed the bid request form and included it in the bid submittal L Signed the Terms and Conditions and included it in the bid submittal LJ Provided a certificate of insurance according to the City s Insurance Requirements naming the City of Athens TN as an additional insured or a letter from your insurance provider stating that insurance requirements will be met upon the bid being awarded and included it in the bid submittal LJ Completely filled out any bid cost sheets or other information stating the amount of your bid and included it in the bid submittal LJ Filled out and returned your bid in a sealed envelope and taped the bid return address sheet to t
76. The Bilstein front shocks shall include a digressive working piston assembly allowing independent tuning of the compression and rebound damping forces to provide optimum ride and comfort without compromise The working piston design shall feature fewer parts than most conventional twin tube and road sensing shock designs and shall contribute to the durability and long life of the Bilstein shock absorbers Proposals offering the use of conventional twin tube or road sensing designed shocks shall not be considered FRONT SUSPENSION The front suspension shall include a nine 9 leaf spring pack in which the longest leaf measures 54 00 inch long and 4 00 inches wide and shall include a military double wrapped front eye Both spring eyes shall have a case hardened threaded bushing installed with lubrication counter bore and lubrication land off cross bore with grease fitting The spring capacity shall be rated at 21 500 pounds STEERING COLUMN WHEEL The cab shall include a Douglas Autotech steering column shall be a seven 7 position tilt and 2 25 inch telescopic type with an 18 00 inch steering wheel located on the left side of the cab designating the driver s position The steering wheel shall be covered with black absorbite padding The steering column shall contain a horn button self canceling turn signal switch four way hazard switch and headlamp dimmer switch POWER STEERING PUMP The hydraulic power steering pump
77. The upper and lower paint shall meet at a breakline on the cab which shall be located approximately 1 00 inch below the door windows on each side of the cab The breakline shall continue in a straight line approximately 1 00 inch below the windshields on the front of the cab CAB PAINT PINSTRIPE Where the upper and lower paint colors meet a temporary 0 50 inch black pinstripe shall be applied over this break line to offer a more finished look prior to the final pinstripe being installed by the OEM CAB PAINT WARRANTY The cab and chassis shall be covered by a limited manufacturer paint warranty which shall be in effect for ten 10 years from the first owner s date of purchase or in service or the first 100 000 actual miles whichever occurs first CAB PAINT INTERIOR The visible cab structure surfaces shall be painted with a Zolatone 20 71 onyx black texture finish CAB ENTRY DOORS The cab shall include four 4 entry doors two 2 front doors and two 2 crew doors designed for ease of entering and egress when outfitted with an SCBA The doors shall be constructed of extruded aluminum with a nominal thickness of 0 13 inch The exterior skins shall be constructed of 0 13 inch aluminum plate The doors shall include a double rolled style automotive rubber seal around the perimeter of each door frame and door edge which ensures a weather tight fit All door hinges shall be hidden within flush mounted cab doors for a pleasing
78. VAILABLE SPARTAN CHASSIS CANNOT BE HELD RESPONSIBLE NOR PARTICIPATE IN ANY ADDITIONAL CHARGES TO MODIFY THE ORDER TO PROVIDE A VIABLE AND AVAILABLE ENGINE OFFERING THESE CHARGES COULD INCLUDE BUT ARE NOT LIMITED TO CHANGING ENGINE BRAND HORSEPOWER OR UPGRADING TO A 2010 FEDERAL EPA EMISSION COMPLIANT ENGINE ADDITIONAL ORDER CONTENT COULD BE AFFECTED IF THE SELECTED 2007 FEDERAL EPA COMPLIANT ENGINE IS REQUIRED TO CHANGE AS A RESULT OF AVAILABILITY SPARTAN CHASSIS CANNOT BE HELD RESPONSIBLE NOR PARTICIPATE IN ADDITIONAL CHARGES WHICH MAY OCCUR IF ASSOCIATED ORDER OPTION CONTENT CHANGES ARE REQUIRED IN THE EVENT THAT AN ALTERNATIVE ENGINE SELECTION IS REQUIRED THESE CHARGES COULD INCLUDE BUT ARE NOT LIMITED TO CHANGING TRANSMISSION MODEL OR CAB MODEL AN APPROVED QUOTE IN SPARCON IS IN NO WAY A VERIFICATION OF ENGINE AVAILABILITY ALL ORDERS REQUESTING A 2007 FEDERAL EPA EMISSION COMPLIANT ENGINE MUST COMPLY WITH ALL STANDARD PURCHASING AND REQUESTED DELIVERY DATES GUIDELINES POSTED IN SPARCON FOR THE ASSOCIATED DATABOOK FOR THE ORDER OR IT WILL BE REJECTED ANY SALES ORDER WITH A CONFIRMED 2007 FEDERAL EPA EMISSION COMPLIANT ENGINE THAT IS CANCELED WILL BE SUBJECTED TO A CANCELLATION FEE OF TEN THOUSAND DOLLARS 10 000 OR MORE BASED ON WHERE THE ORDER IS IN THE PROCUREMENT OR BUILD PROCESS ANY SALES ORDER WITH A CONFIRMED 2007 FEDERAL EPA EMISSION COMPLIANT ENGINE THAT CANNOT BE DELIVERED ON OR PRIOR TO THE REQUESTED DELIVERY DATE WHICH MUST COM
79. acity Test All items listed in NFPA Minimum Load Definition shall be activated with the engine shut off After 10 minutes of operation the items 1 7 shall be deactivated After deactivation the battery system shall have ample reserve to start the engine ALTERNATOR PERFORMANCE TEST AT IDLE The second electrical test to be performed shall be Alternator Performance Test at Full Load All electrical loads shall be activated with the engine running up to the governed rpm for two hours During the test the system voltage shall not drop below 11 7 volts or have excessive battery discharge for more than 120 seconds Any loads not defined in the NFPA Minimum Electrical Load may be load managed to pass test TEST CONDITIONS All electrical testing shall be performed with the engine compartment at approximately 200 degrees 12 VOLT WIRING SYSTEM All 12 volt electrical wiring shall be SXL cross link rated to carry 125 of the maximum current for which the circuit is protected The wire shall be of sufficient size so that voltage drop in any electrical device shall not exceed 10 All wiring shall be color number and function coded with the number and function being printed every three inches along the entire length of all apparatus body wires as required by NFPA 1901 All wiring shall be routed through heavy duty PVC split loom securely attached and protected against heat oil and physical damage All locations where the wire passes through a body pan
80. ainted with the same color as the remaining interior SEAT FRAME FORWARD FACING STORAGE ACCESS There shall be two 2 access points to the seat frame storage area one 1 on each side of the seat frame Each access point shall be covered by a hinged door which measures 15 00 inches in width X 10 63 inches in height CAB FRONT UNDERSEAT STORAGE ACCESS The left and right under seat storage areas shall have a removable aluminum cover SEAT COMPARTMENT DOOR FINISH All underseat storage compartment access doors shall have a Zolatone 20 71 onyx black texture finish WINDSHIELD WIPER SYSTEM The cab shall include a parallel arm wiper system which shall clear the windshield of water ice and debris There shall be two 2 windshield wipers one 1 for the driver and one 1 for the officer which shall be affixed to a rod style arm The system shall include dual motors which shall initiate the arms in which both the driver and officer windshield wipers are attached initiating a back and forth motion for each wiper The wiper motors shall be activated by an intermittent wiper control located within easy reach of the driver s position ELECTRONIC WINDSHIELD FLUID LEVEL INDICATOR The windshield washer fluid level shall be monitored electronically When the washer fluid level becomes low the yellow Check Message Center indicator light on the instrument panel shall illuminate and the message center in the speedometer shall d
81. all be surface mounted to the front fascia of the cab within a chrome bezel in the inboard position INBOARD FRONT WARNING LIGHTS COLOR The front warning lights mounted on the fascia in the inboard positions shall be red with a clear lens FRONT WARNING SWITCH The front warning lights shall be controlled via rocker switch on the main panel This switch shall be clearly labeled for identification INTERSECTION WARNING LIGHTS The chassis shall include two 2 Whelen series 600 Super LED 4 00 inch X 6 00 inch intersection warning lights one 1 each side which shall offer multiple flash patterns including steady burn for solid colors and multiple flash patterns for split colors INTERSECTION WARNING LIGHTS COLOR The intersection lights shall be red with a clear lens INTERSECTION WARNING LIGHTS LOCATION The intersection lights shall be mounted in the rear position on the side of the bumper SIDE WARNING LIGHTS The cab sides shall include a Whelen series 700 Super LED 3 00 inch X 7 00 inch warning light one 1 each side which shall offer multiple flash patterns including steady burn for solid colors and multiple flash patterns for split colors SIDE WARNING LIGHTS COLOR The warning lights located on the side of the cab shall be red with clear lens SIDE WARNING LIGHTS LOCATION The warning lights on the side of the cab shall be mounted over the front wheel well directly over the center of the front
82. all include twelve 12 bright white Gen3 LEDs LH EXTERIOR COMPARTMENT INTERIOR FINISH The interior of the left hand exterior compartment shall have a Zolatone 20 71 onyx black texture finish RH EXTERIOR REAR COMPARTMENT The cab shall offer an exterior compartment on the right side of the cab behind the rear door The compartment opening shall be 16 00 inches wide X 83 34 inches high The compartment size shall be 17 34 inches wide X 87 00 inches high X 21 19 inches deep below the floor The compartment shall be 18 50 inches wide X 66 00 inches high and full depth above the floor The forward facing wall of the compartment shall include the complete rear wall structure to allow seat frames to be mounted forward of the compartment The compartment shall have a 16 63 inch wide X 84 00 inch high X 1 50 inch thick hinged box pan style flush mount door with a bright aluminum tread plate inner panel and a bent D ring slam latch The door shall open towards the rear of the cab There shall be a switch to activate a light inside the compartment and the open compartment warning light in the cab in the event the door is left ajar RIGHT HAND EXTERIOR REAR COMPARTMENT LIGHTING There shall be one 1 SoundOff Signal brand LED strip light installed to illuminate the exterior rear compartment on the right side of the cab The strip light shall be 43 00 inches long and shall include twelve 12 bright white Gen3 LEDs RH EXTERIOR COMPARTMENT INTE
83. allbe permitted to be used MAIN OVERCURRENT PROTECTION DEVICE A main overcurrent protection device shall be provided on the generator The device shall be factory installed by the generator manufacturer 37 WIRING METHODS All fixed wiring systems shall be either metallic or nonmetallic liquid tight conduit rated at not less than 194 degrees fahrenheit or shall be type SO or SEO with a WA suffix rated at 600 volts at not less than 194 degrees Fahrenheit Electrical cord or conduit shall not be attached to chassis suspension components water or fuel lines air or air brake lines fire pump piping hydraulic lines exhaust system components or low voltage wiring All wiring shall be separated by a minimum of 12 or properly shielded from exhaust piping and shall be separated from any fuel lines by a minimum of 6 Electrical cord or conduit shall be supported within 6 of any junction box and at a minimum of every 24 of continous run Supports shall be made of nonmetallic materials or corrosion protected metal All supports shall be of a design that does not cut or abrade the conduit or cable and shall be mechanically fastened to the vehicle NFPA 1901 110 220 VOLT POWER SOURCE TESTING E ical S Testing ly connected devices and equipment shall be subjected to a dielectric voltage withstand test of 900 volts for one minute The test shall be conducted between live parts and the neutral conductor and between live parts and the vehi
84. and backup lights BACKUP ALARM A Code 3 or equal model DAP50 97db backup alarm shall be provided and shall automatically activate when the apparatus transmission is placed into reverse The backup alarm shall exceed all NFPA1901 and SAE J994 Type D requirements and testing EMERGENCY LIGHTING SWITCHING SYSTEM FOR CUSTOM CHASSIS The switching system shall be provided by the fire chassis manufacturer and is further described in the chassis specifications ZONE A UPPER WARNING LIGHTING The lightbar shall be provided on the chassis Specifications for the lightbar are listed in the chassis specifications ZONE C UPPER WARNING LIGHTING REAR Two Whelen model 9OROOF R red 7 x 9 LED s shall be mounted on the upper rear area of the appa ratus one each side with clear lenses 34 ZONES B amp D LOWER WARNING LIGHTING SIDES Zone B Right Side Lower Lighting Three Whelen model 60RO2FRR red LED lights shall be provided on the right side One light shall be mounted as low and as far forward on the apparatus cab as possible one shall be mount ed on the mid section and one shall be mounted as low and as far rearward as possible on the apparatus body Zone D Left Side Lower Lighting Three Whelen model GORO FRR red LED lights shall be provided on the left side One light shall be mounted as low and as far forward on the apparatus cab as possible one shall be mounted on the mid section and one shall be mounted as low and a
85. ardness of H 2H The direct impact resistance test per ASTM D2794 shall have an impact resistance of 120 00 inches per pound at 2 mils The salt spray resistance per ASTM B 117 97 shall pass 500 hours of salt spray test The applied process shall allow the application of other products over it and still maintain or exceed the 500 hours salt spray test Any proposals offering painted frame with variations from the above process shall not be accepted The film thickness of vendor supplied parts shall also be sufficient to meet the performance standards as stated above The chassis under carriage consisting of frame axles driveline running gear air tanks and other chassis mounted components shall be painted with gloss black paint Paint shall be applied prior to airline and electrical wiring installation FRONT BUMPER A one piece two 2 rib wrap around style polished stainless steel front bumper shall be provided The material shall be 10 gauge 304 stainless steel 12 00 inches high and 99 00 inches wide FRONT BUMPER EXTENSION LENGTH The front bumper shall be extended approximately 24 00 inches ahead of the cab FRONT BUMPER EXTENSION FRAME WIDTH The front bumper extension frame shall feature an overall width of 34 25 inches FRONT BUMPER WINCH The front bumper shall include a Ramsey model RE12000 electric winch with 12 000 pound rated line pull 12 volt electric winch shall be installed in the center of the front bumper
86. cated directly behind the officer seat SEAT CREW REAR FACING OUTER The crew area shall include a seat in the rear facing outboard position which shall be a Seats Inc 911 ABTS series The seat shall feature a tapered and padded seat and cushion The seat shall feature an all belts to seat ABTS style of safety restraint The ABTS feature shall include a three point shoulder harness with the lap belt and automatic retractor as an integral part of the seat assembly The buckle portion of the seat belt shall extend from the seat base towards the driver position within easy reach of the occupant The minimum vertical dimension from the seat H point to the ceiling for each belted seating position shall be 35 00 inches This model of seat shall have successfully completed the static load tests by FMVSS 207 210 This testing shall include a simultaneous forward load of 3000 pounds each on the lap and shoulder belts and twenty 20 times the weight through the center of gravity This model of seat installed in the cab model as specified shall have successfully completed the dynamic sled testing using FMVSS 208 as a guide with the following accommodations In order to reflect the larger size outfitted firefighters the test dummy used shall be a 95th percentile hybrid III male weighing 225 pounds rather than the 50th percentile male dummy weighing 165 pounds as referenced in FMVSS 208 The model of seats shall also have successfully completed the fla
87. cated on the left side and right side of the chassis securely bolted to the frame rails The battery trays shall be coated with the same material as the frame The battery trays shall include drain holes in the bottom for sufficient drainage of water A durable non conducting interlocking mat made by Dri Dek shall be installed in the bottom of the trays to allow for air flow and help prevent moisture build up The batteries shall be held in place by non conducting phenolic resin hold down boards BATTERY CABLE The starting system shall include cables which shall be protected by 275 degree F minimum high temperature flame retardant loom sealed and encapsulated at the ends with heat shrink and sealant BATTERY JUMPER STUD The starting system shall include battery jumper studs These studs shall be located in the forward most portion of the driver s side lower step The studs shall allow the vehicle to be jump started charged or the cab to be raised in an emergency in the event of battery failure ALTERNATOR The charging system shall include a 320 amp Leece Neville 12 volt alternator The alternator shall include a self exciting integral regulator BATTERY CONDITIONER A Kussmaul 1200 battery conditioner shall be supplied The battery conditioner shall be mounted in the cab behind the driver s seat BATTERY CONDITIONER DISPLAY A Kussmaul battery conditioner display shall be supplied The battery conditioner display
88. ce to tension compression and bending An outer sheath consisting of a continuous strand mat to prevent lineal splitting and shipping shall surround the core The sheath shall also serve to draw the protective resin to the bar surface Both reinforcements shall be pulled through an isophthalic polyester resin treated with antimony trioxide for fire resistance to form a solid length The flooring shall then be protected with a polyurethane coating to screen out ultraviolet rays This gray coating shall be baked on 68 WIDE HOSEBED 25 The hosebed shall be 68 wide from side to side HOSEBED CAPACITY The hosebed shall have the capacity to carry the following hoseload HOSEBED DIVIDER S There shall be one 1 hosebed divider s in the main hosebed to partition off hose The divider s shall be constructed of 3 16 thick aluminum plate material The lower edge of the divider s have a two inch 90 degree bend toward one side and a 2 x 2 x 3 16 aluminum angle welded to the other side The divider s shall be adjustable by sliding in tracks which are recessed flush into the hosebed flooring one on front and one on rear The divider shall be held in place by two bolts on each end of the divider s The upper rear corner of the divider s shall have a minimum of a 3 radius cut HOSEBED COVER WITH VELCRO FASTENERS A heavy duty vinyl coated nylon hosebed cover shall be provided to protect the hoseload from the weather The cover sha
89. chaser shall revise the height dimension on the plate UNDERWRITERS LABORATORIES TESTING The apparatus shall undergo an Underwriters Laboratories Certification Test to insure that the completed apparatus meets the requirements of NFPA 1901 The certificate shall be provided to the purchaser upon completion Underwriters Laboratories shall also perform the required testing on the entire installed electrical system Absolutely no self certification by the apparatus manufacturer shall be acceptable MANUFACTURER S RECORD CERTIFICATION The contractor shall supply at the time of delivery at least one copy of the following documents 1 The manufacturers record of apparatus construction details including the following information Owners name and address Apparatus manufacturer model and serial number Chassis make model and serial number GAWR of front and rear axles Front tire size and total rated capacity in pounds kg Rear tire size and total rated capacity in pounds kg Chassis weight distribution in pounds with water and manufacturer mounted equipment front and rear Engine make model serial number rated horsepower and related speed and governed speed Type of fuel and fuel tank capacity Electrical system voltage and alternator output in amps Battery make model and capacity in cold cranking amps CCA Chassis transmission make model and serial number and if so equipped chassis transmission PTO s make model and gear ratio Ra
90. chassis at Spartan Chassis in Charlotte Michigan The customer the dealer or the OEM shall be responsible for all travel costs and arrangements The date of the chassis inspection shall be determined based on the requested chassis completion date OEM production schedules the chassis off line date and the chassis completion date Part 2 CERTIFICATION OF NFPA 1901 COMPLIANCE As per NFPA 1901 the Purchaser shall assume the responsibility of determining prior to the purchase of the apparatus who will be responsible for ensuring that all aspects of NFPA 1901 2009 are met The manufacturer shall be responsible for providing or performing only the items requested by the purchaser in the documents provided to the manufacturer by the purchaser Written certification shall be provided by the manufacturer stating that the delivered apparatus complies with the NFPA 1901 2009 Standard If the purchaser has elected to provide perform outsource and or contract with a third party any item required by NFPA 1901 2009 per the previous paragraph the manufacturer shall provide upon delivery a Statement of Exceptions per Chapter 4 of NFPA 1901 2009 This Statement of Exceptions shall include 1 A seperate specification of the section of the NFPA Standard for which the apparatus is lacking compliance 2 A description of the particular aspect of the apparatus that is not compliant 3 A description of the further changes or modifications to
91. cle frame with any switches in the circuit closed position This test shall be conducted after all body work has been completed Electrical polarity verification shall be made of all permanently wired equipment and receptacles to determine that connections have been properly made NFPA Operational Test turer shall perform the following operational test and shall certify that the power source and any devices that are attached to the line voltage electrical system are properly connected and in working order The prime mover shall be started from a cold start condition and the line voltage electrical system loaded to 100 percent of the nameplate rating The power source shall be operated at 100 percent of its nameplate voltage for a minimum of 2 hours unless the system meets category certification as defined in NFPA 1901 120 240 VOLT ELECTRICAL EQUIPMENT INSTALLATION All 120 240 electrical equipment shall be installed by the apparatus manufacturer This shall include any item related to the system including but not limited to the following Generator All scenelighting accessories 38 All outlets and cord reels where applicable Breaker panel To maintain the integrity of the entire apparatus electrical system all 120 240 equipment must be installed by the appratus manufacturer Installation by the apparatus manufacturer will also allow the electrical system to be NFPA tested during the U L pump certification testing procedure
92. constructed of an unbreakable type clear poly type flexible material housed in an aluminum extrusion mounted behind a brushed stainless steel light shield provided across the top of the hinged access door CLASS ONE PUSH PULL VALVE CONTROL HANDLES All valve control handles shall be Class One model 100348 push pull type T handles The T handles shall be chrome plated zinc and shall have a 1 x 3 recessed area for the color coded identification label The panel mounting plate shall be chrome plated and shall be secured to the panel using four stainless steel bolts with locking type fasteners The control rod shall be 3 4 hard coated anodized aluminum with a universal ball swivel connection The control rod shall have a self aligning handle to insure smooth push pull activation DISCHARGE VALVE CONTROL HANDLE LAYOUT All discharge valve control handles shall be located in one or two horizontal lines across the mid section of the pump panel All discharge valve control handles shall be located immediately below their corresponding pressure gauge for ease of pump operation STAINLESS STEEL VALVE CONTROL LINKAGES All manual valve controls shall have control rod linkages constructed of 1 2 stainless steel rod or pipe and shall 14 implement heavy ball swivel joints and clevises for smooth valve operation Plain painted or coated control rods are not acceptable No Exception PRESSURE VACUUM TEST PLUGS Underwriter s test plug adapters s
93. d hand REARVIEW MIRRORS Retrac Aerodynamic West Coast style single vision mirror heads model 613285 shall be provided and installed on each of the front cab doors The mirrors shall be mounted via 1 00 inch diameter tubular stainless steel arms to provide a rigid mounting to reduce mirror vibration The mirrors shall measure 8 00 inches wide X 19 00 inches high and shall include an 8 00 inch convex mirrors with a stainless steel back model 980 4 installed below the flat glass to provide a wider field of vision The flat mirrors shall be motorized with remote horizontal and vertical adjustment The control switches shall be mounted within easy reach of the driver The convex mirrors shall be manually adjustable The flat mirror glass shall be heated for defrosting in severe cold weather conditions The mirror backs shall be constructed of vacuum formed chrome plated ABS plastic housings that are corrosion resistant and shall include an amber marker light The mirrors shall be manufactured with the finest quality non glare glass REARVIEW MIRROR HEAT SWITCH The heat for the rearview mirrors shall be controlled through a rocker switch in the mirror control panel on the driver s side dash CAB FENDER Full width wheel well liners shall be installed on the extruded cab to limit road splash and enable easier cleaning Each two piece liner shall consist of an inner liner 16 00 inches wide made of vacuum formed ABS composite and an
94. d on the rear of the apparatus one 1 each side The lights shall be controlled by lighthead mounted switches and shall be capable of 360 degree rotation and 90 degrees above and below horizontal tilt The lights shall be subjected to load management shedding to comply with NFPA 1901 10 KW SMART POWER HYDRAULIC GENERATOR SET A Smart Power model HR 10 10 000 watt hydraulic generator shall be provided The generator is designed specifically for mounting on top of the vehicle at the customer specified location but can also be easily separated into its three major components tray cooler fan assembly and reservoir for mounting in custom applications The generator system shall come with a standard 5 year 1 000 hour fully transferable warranty from the manufacturer The unit shall come equipped with generator tray assembly which includes the generator hydraulic motor cooler fan electronics package 10 micron spin on fluid filter and reservoir axial piston hydraulic pump with pressure compensated control and Command and Control Center CCC display with all required wiring harnesses The CCC shall be an interactive operator control center equipped with smart touch solid state buttons with displays for voltage frequency amperage hour meter service reminders operator warnings system faults and diagnostics Standard electronics package shall include smart start engagement to reduce mechanical stress precise voltage and frequency control
95. d to secure the substructure to the chassis frame rails shall be hardened steel with locking type nuts After complete assembly of the tank cradle sub structure the entire assembly shall be hot dipped galvanized for superior corrosion protection Due to the extreme duty that this apparatus will experience during its intended service life and to prevent rusting and corrosion from shortening the service life of this apparatus sub frames fabricated of painted undercoated steel or aluminum tubing shall not be acceptable 20 YEAR TANK CRADLE STRUCTURAL WARRANTY The tank cradle shall have a 20 year structural warranty NO EXCEPTIONS 20 YEAR TANK CRADLE CORROSION WARRANTY The tank cradle shall have a warranty covering structural failure due to corrosion perforation This warranty shall be in 19 effect for 20 years after delivery of the apparatus to the customer NO EXCEPTIONS 20 YEAR REAR STRUCTURAL SUPPORT WARRANTY The tank cradle shall have a warranty covering structural failure due to corrosion perforation This warranty shall be in effect for 20 years after delivery of the apparatus to the customer NO EXCEPTIONS The rear structural support shall have a 20 year structural warranty NO EXCEPTIONS 20 YEAR REAR STRUCTURAL SUPPORT CORROSION WARRANTY The rear structural support shall have a warranty covering structural failure due to corrosion perforation This warranty shall be in effect for 20 years after delivery of the apparatus to
96. e a control module intake pressure sensor discharge pressure sensor and cables The control module case shall be waterproof and have dimensions not to exceed 5 1 2 high by 10 1 2 wide by 2 deep Inputs for monitored information shall be from a J1939 databus or independent sensors Outputs for engine control shall be on the J1939 databus or engine specific wiring The following continuous displays shall be provided Pump discharge shown with four daylight bright LED digits more than 1 2 high Pump Intake shown with four daylight bright LED digits more than 1 2 high Pressure RPM setting shown on a dot matrix message display Pressure and RPM operating mode LEDs Throttle ready LED Engine RPM shown with four daylight bright LED digits more than 1 2 high Check engine and stop engine warning LEDs Oil pressure shown on a dual color green red LED bar graph display Engine coolant temperature shown on a dual color green red LED bar graph display Transmission Temperature shown on a dual color green red LED bar graph display Battery voltage shown on a dual color green red LED bar graph display The dot matrix message display shall show diagnostic and warning messages as they occur It shall show monitored apparatus information stored data and program options when selected by the operator All LED intensity shall be automatically adjusted for day and night time operation The program shall store the accumulated operating hours for the pu
97. e cab roof so not to interfere with light bars or other roof mounted equipment The antenna base shall be an Antenex model MABVTS8 made for either a 0 38 inch or 0 75 inch receiving hole in the antenna and shall include 17 00 foot of RG58 A U cable with no connector at the radio end of the cable The antenna base design provides the most corrosion resistance and best power transfer available from a high temper all brass construction and gold plated contact design The antenna base shall be provided by Spartan COMMUNICATION ANTENNA CABLE ROUTING The antenna cable shall be routed from the antenna base mounted on the roof to the area behind the left hand front seat CAB EXTERIOR PROTECTION The cab face shall have a removable plastic film installed over the painted surfaces to protect the paint finish during transport to the body manufacturer FIRE EXTINGUISHER A 2 50 pound D O T approved fire extinguisher with BC rating shall be shipped loose with the cab ROAD SAFETY KIT The cab and chassis shall include one 1 emergency road side triangle kit DOOR KEYS The cab and chassis shall include a total of four 4 door keys for the manual door locks DIAGNOSTIC SOFTWARE ROLLTEK The cab and chassis shall include diagnostic software for the RollTek system shipped loose with the vehicle The software kit number F101560 shall include an interface module with connectors to link a laptop computer to the vehicle for diagnostic
98. e cab shall be designed for heavy duty service utilizing superior strength and capacity for the application of protecting the occupants of the vehicle This style of cab shall offer up to ten 10 seating positions The cab shall incorporate a fully enclosed design with side wall roof supports allowing for a spacious cab area with no partition between the front and rear sections of the cab To provide a superior finish by reducing welds that fatigue cab metal the roof the rear wall and side wall panels shall be assembled using a combination of welds and proven industrial adhesives designed specifically for aluminum fabrication for construction The cab shall be constructed using multiple aluminum extrusions in conjunction with aluminum plate which shall provide proven strength and the truest flattest body surfaces ensuring less expensive paint repairs if needed All aluminum welding shall be completed to the American Welding Society and ANSI D1 2 96 requirements for structural welding of aluminum All interior and exterior seams shall be sealed for optimum noise reduction and to provide the most favorable efficiency for heating and cooling retention The cab shall be constructed of 5052 H32 corrosion resistant aluminum plate The cab shall incorporate tongue and groove fitted 6061 T6 0 13 amp 0 19 inch thick aluminum extrusions for extreme duty situations A single formed one 1 piece extrusion shall be used for the A pillar adding stre
99. e foam proportioning system The system shall be capable of handling Class A foam concentrates The foam proportioning operation shall be based in direct measurement of water flows and pressures and remain consistent within the specified flows and pressures The system shall be equipped with a digital electronic control display suitable for installation on the pump panel Incorporated within the motor driver shall be a microprocessor that receives input from the system flowmeter while also monitoring foam concentrate pump output comparing values to ensure that the operators preset proportional amount of foam concentrate is injected into the discharge side of the pump The digital computer display shall enable the pump operator to perform the following control and operation functions for the foam proportioning system A Provide push button control of foam proportioning rates from 0 1 to 3 0 in 0 1 increments B Show current flow per minute of water C Show total volume of water discharged during and after foam operations are completed D Show total amount of foam concentrate consumed E Simulate flow rates for manual operation F Perform setup and diagnostic functions for the computer control microprocessor G Flash a low concentrate warning when the foam concentrate tanks run low H Flash a no concentrate warning and shut the foam concentrate pump off preventing damage to the pump The foam system shall be capable of the following
100. e lid A label shall be provided on the lid that reads CLASS B FOAM TANK FILL and WARNING DO NOT MIX BRANDS AND TYPES OF FOAM 7 x 10 lid CLASS B FOAM TANK BOOSTER TANK INTEGRATION The class B foam tank shall be integrated into the apparatus booster tank The B foam tank shall not be separate from the booster tank 3 TANK TO PUMP A 3 tank to pump line shall be provided between the tank and the pump The tank valve shall be an Akron tank to pump valve with control mounted on the pump operator s panel The piping and valve arrangement shall be capable of flowing a minimum of 500 U S gallons per minute to the pump This flow must be maintained for 80 of the certified tank capacity with the apparatus positioned on level ground 18 An integral built in check assembly shall be provided on the pump The check shall be designed to be an internal part of the pump thus allowing full opening and maximum flow to the pump The check valve shall operate and shall prevent unintentional back filling of the tank through the tank to pump line Connection from the valve to the tank shall be made by using a non collapsible flexible rubber hose TANK CRADLE SUB STRUCTURE HOT DIPPED GLAVANIZED ructural steel The tank cradle substructure shall be designed to provide support to the booster tank The design of the cradle shall be approved by the tank manufacturer Approval of the design shall be provided on request by the purchaser The enti
101. e midship mounted The pump shall be mounted across the chassis frame rails and shall be mounted at the Fire Pump Manufacturer s recommended angular position with the drive shafts The pump shall be free from objectionable pulsation and vibration under all normal operating conditions The engine shall provide sufficient horsepower and revolutions per minute to allow the pump to meet or exceed its rated performance The entire pump both suction and discharge passages shall be hydrostatically tested to a pressure of 600 PSI The pump shall be fully tested at the pump manufacturer s factory to the performance spots as outlined by NFPA 1901 The pump body shall be close grained gray iron and must be horizontally split in two sections for easy removal of the entire impeller shaft assembly and designed for complete servicing from the bottom of the truck without disturbing setting of the pump in the chassis or apparatus piping which is connected to the pump The pump body halves shall be bolted together on a single horizontal face to minimize leakage and facilitate re assembly The impeller shaft shall be stainless steel accurately ground to size and supported at each end by oil or grease lubricated anti friction ball bearings for rigid and precise support The bearings shall be protected from water and sediment by suitable stuffing boxes flinger rings and oil seals The impeller shaft shall be of a two piece construction separable between the pump and pu
102. eadbrite hinged cover shall be provided to enclose the hosewell The hosewell shall have the maximum capacity of 100 of 1 3 4 firehose Passenger side FRONT DISCHARGE HOSE CONNECTION CHROME SWIVEL The hose connection for the discharge shall be located immediately adjacent to the hosewell on the driver s side A 12 chrome plated or polished stainless steel swivel shall be provided The lid for the hosewell shall be notched to allow for the hose to be preconnected Passenger side of bumper Akron 8620 series discharge valve s shall be utilized on the front bumper 1 3 4 discharge s The valve shall be manually controlled from the pump operator s position The valve and piping shall be 2 SIDE MOUNTED SELF CONTAINED MODULAR PUMP COMPARTMENT A self contained modular pump compartment designed for the integral mounting of a midship pump with side mounted pump operator s panel shall be provided The modular design of the pump compartment shall allow the compartment to be fully independent of the apparatus body or cab A minimum 75 inch gap shall be provided between the pump compartment and the apparatus body creating a flexible joint between the pump compartment assembly and the apparatus body An extruded rubber gasket shall be installed in the gap to help prevent entry of road debris snow ice etc into the pump compartment The modular design of the pump compartment shall allow the entire pump system including the pump itself
103. ed 20 foot length of hard suction hose developing a vacuum of at least 20 inches with a drop not exceeding 10 inches in 5 minutes PRIMER FUSE The primer shall be protected with a 250 amp fusable link that is designed to protect the apparatus 12 volt electrical system if the primer motor malfunctions MANIFOLD DRAIN VALVE The pump shall have a manifold type drain valve assembly consisting of a stainless steel plunger in a bronze body with multiple ports The control for the valve shall be on the left side below the left side master intake and above the side running board The valve shall be a rotary type with large easy to grip handle The valve shall be labeled PUMP DRAIN BLEEDER DRAIN VALVES A 3 4 quarter turn Class 1 model 3 4BV ball type bleeder drain valve shall be provided for each discharge and auxiliary intake A hose shall be connected to the bleeder drain that will direct water below the apparatus and away from the immediate pump operator s location 6 LEFT DRIVER SIDE MASTER INTAKE A 6 master intake shall be provided on the left driver side of the apparatus The intake shall have a 6 male National Standard Thread connection The intake shall have a removable screen to prevent the entry of large objects into the pump The screen shall be constructed of a material that will provide cathodic protection to the pump A label shall be provided above the intake that states DRIVER SIDE MASTER INTAKE The label shall be colo
104. ed 3 8 from the top of the tank and shall be welded to both sides and longitudinal partitions of maximum integrity Each of the covers shall have hold downs consisting of 2 polypropylene dowels spaced a maximum of 30 apart These dowels shall extend through the covers and will assist in keeping the covers rigid under fast filling conditions A minimum of two lifting dowels shall be drilled and tapped to accommodate the lifting eyes The sump shall be constructed of 1 2 PT2E polypropylene The sump shall have a 3 NPT threaded outlet on the bottom for a drain plug An anti swirl plate shall be located approximately 2 1 2 above the sump The tank cradle assembly shall be designed to provide support to the tank The assembly shall be approved by the manufacturer of the tank BOOSTER TANK CAPACITY 750 GALLONS The poly booster tank shall have a capacity of 750 U S Gallons BOOSTER TANK FILL TOWER LEFT SIDE FRONT The tank shall have a combination vent and manual fill tower The fill tower shall be constructed of 1 2 polypropylene and shall be a minimum dimension of 10 x 10 outer dimension The tower shall be located in the left front corner of the hosebed The tower shall have a 1 4 thick remov able polypropylene screen and polypropylene hinged type cover 4 TANK OVERFLOW A 4 diameter tank vent overflow shall be provided and integrated intot he tank The piping shall be a minimum of schedule 40 polypropylene that is designed to run thr
105. ed by the chassis manufacturer to accommodate the mid ship split shaft pump as specified by the apparatus manufacturer MIDSHIP PUMP GEARBOX MODEL The midship pump gearbox provisions shall be for a Waterous CSUC20 pump MIDSHIP PUMP RATIO The ratio for the midship pump shall be 2 27 1 MIDSHIP PUMP GEARBOX DROP The Waterous pump gearbox shall have a C medium length drop length MIDSHIP PUMP LOCATION C L SUCTION The pump driveline shall include a centerline of the rear axle to the center line of the suction dimension of 100 00 inches FUEL FILTER WATER SEPARATOR The fuel system shall have a Fleetguard FS1003 fuel filter water separator as a primary filter The fuel filter shall have a drain valve A water in fuel sensor shall be provided and wired to an instrument panel lamp and audible alarm to indicate when water is present in the fuel water separator A secondary fuel filter shall be included as approved by the engine manufacturer FUEL LINES The fuel system supply and return lines installed from the fuel tank to the engine shall be reinforced nylon tubing rated for diesel fuel The fuel lines shall be brown in color and connected with brass fittings FUEL SHUTOFF VALVE A fuel shutoff valve shall be installed in the fuel draw line at the primary fuel filter to allow the fuel filter to be changed without loss of fuel to the fuel pump A second fuel shutoff valve shall be installed in the fu
106. el draw line near the fuel tank to allow maintenance to be performed with minimal loss of fuel FUEL TANK The fuel tank shall have a capacity of sixty five 65 gallons and shall measure 35 00 inches in width X 18 50 inches in height X 24 00 inches in length The baffled tank shall be made of 14 gauge aluminized steel The exterior of the tank shall be painted with a PRP Corsol black anti corrosive exterior metal treatment finish This results in a tank which offers the internal and external corrosion resistance The tank shall have a vent port to facilitate venting to the top of the fill neck for rapid filling without blow back and a roll over ball check vent for temperature related fuel expansion and draw The tank is designed with dual draw tubes and sender flanges The tank shall have 2 00 inch NPT fill ports for right or left hand fill A 0 50 inch NPT drain plug shall be centered in the bottom of the tank The fuel tank shall be mounted below the frame behind the rear axle Two 2 three piece strap hanger assemblies with U straps bolted midway on the fuel tank front and rear shall be utilized to allow the tank to be easily lowered and removed for service purposes Rubber isolating pads shall be provided between the tank and the hanger strap assemblies Strap mounting studs through the rail hidden behind the body shall not be acceptable FUEL TANK FILL PORT The fuel tank fill ports shall be offset with the right fill port
107. el shall be protected with electrical grommets All connections shall be made using mechanical connectors and be screwed to terminal or junction box with machine screws Wire nut insulation displacement or piercing connections shall not be used All circuits shall be provided with properly rated low voltage over current protective devices of the automatic reset type A removable bulkhead shall that extends from the floor to the ceiling of both side rear compartments shall be provided to protect rear wiring HARD WIRED ELECTRICAL SYSTEM The apparatus body electrical system shall incorporate a hard wired electrical system Any type of multiplex system will not be acceptable LICENSE PLATE LIGHT BRACKET An Arrow model 437 00 332 chrome plated license plate light shall be provided on the rear of the apparatus The light shall function with the head light switch 32 A license plate mounting bracket shall be provided that spaces the license plate away from the apparatus body CLEARANCE LIGHTS REFLECTORS All apparatus body clearance lights shall be LED style All lower clearance lights and reflectors shall be mounted in a manner that provides protection from damage and shall comply with FMVSS 108 regulations MID MOUNTED SIDE TURN SIGNAL L E D A mid mounted amber LED side turn signal shall be provided in the mid section area of the apparatus on both sides The low profile signal shall be recessed into the side rubrail for protection
108. em Output fourteen 14 shall provide a low voltage warning for an isolated battery Output fifteen 15 is a user configurable output and shall be programmable for activating between 10 50 and 15 00 volts Output sixteen 16 shall provide a low voltage alarm that activates at the NFPA required 11 80 volts The TSM shall have a digital display to indicate system voltage in normal operation mode and also indicate the output configuration during programming mode The TSM shall be protected against reverse polarity and shorted outputs and be enclosed in a metal enclosure to enhance EMI RFI protection DATA RECORDING SYSTEM The chassis shall have a Class One Vehicle Data Recorder system installed The system shall be designed to meet NFPA 1901 The following information shall be recorded Vehicle Speed Acceleration Deceleration Engine Speed Engine Throttle Position ABS Event Seat Occupied Status Seat Belt Status Master Optical Warning Device Switch Position Time Date Each portion of the data shall be recorded at the specified intervals and stored for the specified length of time to meet NFPA 1901 guidelines and shall be retrievable by connecting a laptop computer to the VDR system POWER amp GROUND STUD A 40 amp battery direct power and ground stud shall be provided and installed in the electrical distribution panel The stud shall be size 10 and protected with a 40 amp circuit breaker AUXILIARY POWER amp GROUND STUD
109. f the panel Five 5 of the top row of switches shall be rocker type and the left one 1 shall be the headlight switch The remaining switches shall consist of one 1 windshield wiper washer control switch and one 1 instrument lamp dimmer switch A rocker switch with a blank legend installed directly above shall be provided for any position not designated by a specific option The non designated switches shall be two position black switches with a green indicator light Each blank switch legend can be custom engraved by the body manufacturer All switch legends shall have red backlighting provided SWITCHES RIGHT PANEL The right dash panel shall include eight 8 rocker switch positions in a four 4 over four 4 switch configuration A rocker switch with a blank legend installed directly above shall be provided for any position without a switch and legend designated by a specific option The non specified switches shall be two position black switches with a green indicator light Each blank switch legend can be custom engraved by the body manufacturer All switch legends shall have red backlighting provided SEAT BELT WARNING A Class One seat belt warning system integrated with the Vehicle Data Recorder system shall be installed for each seat within the cab The system shall activate an indicator light in the instrument panel a digital seat position indicator with a seat position legend in the switch panel and an audible alarm
110. flow rates at given foam 5 000 gpm 0 1 2 500 gpm 0 2 1 000 gom 0 5 500 gpm 1 0 166 gpm 3 0 A 12 volt electric motor driven positive displacement foam concentrate pump shall be provided The pump capacity shall be 5 0 gpm with a maximum operating pressure up to 400 psi The pump motor electronic driver which is mounted to the base of the pump shall receive signals from the computer control display and power the 3 4 hp electric motor in a variable speed duty cycle to ensure that the correct proportion of concentrate is injected into the water stream A full flow check valve shall be provided in the discharge piping to prevent foam contamination in the fire pump and water tank A 5 psi opening pressure check valve shall be provided in the concentrate line The A B foam supplies shall be provided from the integral foam tanks described later in these specifications An installation and operation manual shall be provided for the foam system A RFI EMI suppression kit shall be installed on the system PADDLEWHEEL FLOWMETER A Foam Pro 3 tee mounted model 2660 0029 flowmeter kit shall be provided and shall read total flow from all foam capable discharges A model 3430 0452 grooveless victaulic coupling kit shall be provided to allow for easy future maintenance on the system FOAM CAPABLE DICHARGES The following discharges shall be foam capable Front bumper discharge Front 1 75 cross lay Rear 2 5 cross lay Left rea
111. for Automotive Fire apparatus published by the National Fire Protection Association and printed in Pamphlet 1901 WATEROUS PUMP WARRANTY The Waterous pump and related Waterous components shall be be covered by a 5 year conditional warranty covering defects in materials and or workmanship Any component that is provided by Waterous with the pump system but not manufactured by Waterous will be covered by warranties of the respective manufacturer Part failure due to normal wear and tear or improp er use shall not be covered under this warranty UNDERWRITER S LABORATORY CERTIFICATION The completed apparatus shall be tested and approved by the independent testing company Underwriters Laboratories Inc The manufacturer of the apparatus shall be responsible for all costs involved in this test The Certification of inspection and approval shall be presented to the Fire Chief of the Department upon delivery of the completed apparatus PUMP PERFORMANCE 1 500 U S GPM The pump shall be a single stage centrifugal with a class A rated capacity of 1 500 United States gallons per minute The pump shall deliver the percentage of rated discharge pressures as indicated below 100 percent of rated capacity at 150 pounds net pressure 70 percent of rated capacity at 200 pounds net pressure 50 percent of rated capacity at 250 pounds net pressure 100 percent of rated capacity at 165 pounds net pressure PUMP CONSTRUCTION The fire pump shall b
112. formation required for inspections to comply with NFPA 1914 10 If the apparatus has a fixed line voltage power source the certification of the test for the fixed power source 11 If the apparatus is equipped with an air system test results of the air quality the SCBA fill station and the air system installation 12 Weight documents from a certified scale showing actual loading on the front axle rear axle s and overall fire apparatus with the water tank full but without personnel equipment and hose 13 Written load analysis and results of the electrical system performance tests 14 When the apparatus is equipped with a water tank the certification of water tank capacity OOND TRWN VEHICLE ROLLOVER STABILITY The apparatus chassis shall be equipped with a stability control system and shall be certified to NFPA 1901 Rollover Stabillity requirements VEHICLE DATA LOGGER CHASSIS PROVIDED The vehicle data logger shall be provided from the chassis manufacturer SEAT BELT WARNING SYSTEM CHASSIS PROVIDED The seat belt warning system shall be provided from the chassis manufacturer ZICO UHH 1 FIRE HELMET MOUNTINGS Five 5 Zico model UHH 1 fire helmet brackets shall be provided and mounted in the apparatus cab Ship loose for dealer install PAINT PROCEDURE PPG DELFLEET BASE COAT CLEAR COAT 45 After the apparatus body has been fully assembled and all mounting holes etc have been either punched machined or drilled
113. g type nuts RIGHT FRONT COMPARTMENT ACCESS STEPS Three NFPA compliant folding steps shall be provided on the right side front compartment face LEFT FRONT COMPARTMENT ACCESS STEPS Three NFPA compliant folding steps shall be provided on the left side front compartment face RIGHT REAR ACCESS STEPS Three NFPA compliant folding steps shall be provided on the rear of the apparatus on the right side LEFT REAR ACCESS STEPS Three NFPA compliant folding steps shall be provided on the rear of the apparatus on the left side NFPA KNURLED FINSH HANDRAILS All handrails shall be 1 1 4 diameter extruded aluminum knurled finish with chrome plated stanchions Rubber gaskets shall be provided between the stanchions and any painted surfaces The rails shall comply with NFPA 1901 LEFT REAR VERTICAL HAND RAILS rovided on the left rear of the apparatus for boarding the rear step and using the left rear hosebed access steps RIGHT REAR VERTICAL HAND RAILS One NFPA compliant handrail shall be provided on the right rear of the apparatus for boarding the rear step and using the right rear hosebed access steps RIGHT FRONT GRAB RAIL A12 NEPA compliant horizontal handrail shall be provided on on the right front of the apparatus towards the front of the hosebed 30 LEFT FRONT GRAB RAIL A 12 NFPA compliant horizontal handrail shall be provided on on the left front of the apparatus towards the front of the hosebed RIGHT REAR GRAB
114. hall allow seventy five percent 75 light transmittance CLIMATE CONTROL The cab shall include a 57 600 BTU 425 CFM front overhead heater defroster which shall be provided and installed above the windshield between the sun visors The cab shall also include a combination heater air conditioning unit mounted on the engine tunnel This unit shall offer eight 8 adjustable louvers 4 forward facing four rearward facing a temperature control valve and two 2 blowers offering three 3 speeds which shall be capable of circulating 550 cubic feet of air per minute The unit shall be rated for 42 500 BTU Hr of cooling and 36 000 BTU Hr of heating The temperature and blower controls shall be located on the heater air conditioning unit All defrost heating systems shall be plumbed with one 1 seasonal shut off valve at the front corner on the right side of the cab The air conditioner lines shall be a mixture of custom bent zinc coated steel fittings and Aero quip GH 134 flexible hose with Aero Quip EZ Clip fittings CLIMATE CONTROL ACTIVATION The heating controls and air conditioning if included shall be located on the climate control unit A C CONDENSER LOCATION A roof mounted A C condenser shall be installed centered on cab forward of raised roof against the slope rise A C COMPRESSOR The air conditioning compressor shall be a belt driven engine mounted open type compressor that shall be capable of producing a min
115. hall be provided for connection of pump test gauges FRC WL2000 TANKVISION TANK GAUGE A FRC model WL2000 tank gauge shall be provided on the pump panel The gauge shall feature a 180 degree highly visible wide view LED display showing the exact level of the booster tank The gauge shall provide a flashing warning whe tank volume drops below 25 and down chasing lights when tank is nearly or completely empty The gauge shall implement a self calibrating pressure sensor system to indicate the tank volume A probe type of system shall not be used FRC WL2700 TANKVISION CLASS B FOAM TANK GAUGE A FRC model WL2700 foam tank gauge shall be provided on the pump panel The gauge shall feature a 180 degree highly visible wide view LED display showing the exact level of the booster tank The gauge shall provide a flashing warning whe tank volume drops below 25 and down chasing lights when tank is nearly or completely empty The gauge shall implement a self calibrating pressure sensor system to indicate the tank volume A probe type of system shall not be used FRC WL2600 TANKVISION CLASS A FOAM TANK GAUGE A FRC model WL2600 foam tank gauge shall be provided on the pump panel The gauge shall feature a 180 degree highly visible wide view LED display showing the exact level of the booster tank The gauge shall provide a flashing warning whe tank volume drops below 25 and down chasing lights when tank is nearly or completely empty The gauge shall i
116. he outside of the bid submittal
117. he top of the door opening The cab shall also include a crew area with up to two 2 cab doors also large enough for personnel in full firefighting gear The rear doors shall offer a clear opening of 31 00 inches wide X 61 00 inches high from the cab floor to the top of the door opening The cab shall incorporate a progressive two 2 step configuration from the ground to the cab floor at each door opening The progressive steps are vertically staggered and extend the full width of each step well allowing personnel in full firefighting gear to enter and exit the cab easily and safely The first step for the driver and officer area shall measure approximately 10 88 inches deep X 31 50 inches wide The intermediate step shall measure approximately 8 63 inches deep X 33 00 inches wide The height from the first step to the intermediate step and the intermediate step to the cab floor shall not exceed 11 00 inches The first step for the crew area shall measure approximately 10 88 inches deep X 21 50 inches wide The intermediate step shall measure approximately 11 50 inches deep X 23 50 inches wide The height from the first step to the intermediate step and the intermediate step to the cab floor shall not exceed 12 50 inches CAB FRONT FASCIA The front cab fascia shall be constructed of 5052 H32 Marine Grade 0 090 of an inch thick one hundred percent primary aluminum plate which shall be an integral part of the cab The cab fascia will encom
118. ided by the Fire Department The Department shall provide the following hose 6 x 10 setup 27 COMPARTMENT SHELF TRACKS ALUMINUM Nine 9 sets consisting of four 4 heavy duty aluminum Uni Strut tracks shall be provided in specified compartments two for each end of shelf The tracks shall not be welded to the apparatus body The Uni strut tracks shall allow the shelving to be positioned at any location in the compartment by simply loosing a bolt on each end of the shelf pushing inward on the bolt and sliding the shelf to the desired location COMPARTMENT SHELVING SIDE COMPARTMENTS There shall be Two 2 shelves provided constructed of 125 smooth aluminum with a brushed finish on the outer edge The shelves shall have a 2 upward bend on the front and rear edges DAW and PAW above the rollout trays DRIVER WHEEL WELL ROLL OUT DRAWER There shall be one roll out drawer installed above the rear wheels on the driver s side of the body in the wheel well area The drawer shall be approximately 23 5 deep by 56 wide and have a 300 Ib capacity PASSENGER WHEEL WELL ROLL OUT DRAWER There shall be one roll out drawer installed above the rear wheels on the passenger s side of the body in the wheel well area The drawer shall be approximately 23 5 deep by 56 wide and have a 300 Ib capacity DRIVER FRONT WHEELWELL COMPARTMENT There shall be a compartment located in the driver s side wheel well ahead of the rear axle to hold three
119. ided in the driving compartment and shall be energized when the pump shift has been completed This light shall be labeled PUMP ENGAGED When the apparatus is equipped with an automatic transmission a green indicator light be provided in the driver compartment and at the pump operators position and shall be energized when both the pump shift has been completed and the chassis transmission is in pump gear This light shall be labeled OK TO PUMP The light on the pump panel shall be positioned adjacent to and preferably above the throttle control mechanism and shall be marked WARNING DO NOT OPEN THROTTLE UNLESS LIGHT IS ON The pump panel light shall also be energized when the chassis transmission is in the neutral position and the parking brake is engaged WATEROUS MODEL VPO OILLESS PRIMING SYSTEM A Waterous model VPO oilless priming system shall be provided The priming pump shall be an electrically driven positive displacement vane type conforming to standards outlined in National Fire Protection Association 1901 One priming control shall both open the priming valve and start the priming motor The primer shall be capable of taking suction and discharging water with a lift of 10 feet in not more than 30 seconds with the pump dry and using 20 feet of appropriately sized hard suction hose with strainer The system shall develop a vacuum of 22 inches at an altitude of up to 2 000 feet above sea level The vacuum test shall be performed with a capp
120. imum of 13000 BTU at 1500 engine RPMs The compressor shall utilize R 134A refrigerant and PAG oil CAB INSULATION The cab ceiling and walls shall include 1 00 inch thick foam insulation The insulation shall act as a barrier absorbing noise as well as assisting in sustaining the desired climate within the cab interior UNDER CAB INSULATION The underside of the cab tunnel surrounding the engine shall be lined with multi layer foam insulation engineered for application inside diesel engine compartments The insulation shall act as a noise barrier absorbing noise thus keeping the decibel level in the cab well within NFPA recommendations As an additional benefit the insulation shall assist in sustaining the desired temperature within the cab interior The insulation shall measure 56 inch thick including a 1 0 sf PVC barrier and a moisture and heat reflective foil backing reinforced with fiberglass strands The foil surface acts as protection against moisture and other contaminants The insulation shall meet or exceed FMVSS 302 flammability test The insulation shall be cut precisely to fit each section and sealed for additional heat and sound deflection The insulation shall be held in place by 3 mils of acrylic pressure sensitive adhesive and aluminum pins with hard hat hold in place fastening heads INTERIOR TRIM FLOOR The floor of the cab shall be covered with a multi layer mat consisting of 0 25 inch thick sound absorbi
121. ing possible damage The radiator shall be a cross flow design constructed completely of aluminum with welded side tanks The radiator shall include a minimum of a 627 square inch core and shall be bolted to the bottom of the charge air cooler to allow a single depth core thus allowing a more efficient and serviceable cooling system The radiator shall be equipped with a drain cock to drain the coolant for serviceability The cooling system shall include a one piece injected molded Polymer fan blade designed to provide long life in harsh environments Polymer fans provide a significant weight reduction over metal fans providing longer life for fan clutch linings and bearings along with increased fan belt life The cooling system shall be equipped with a surge tank that is capable of removing entrained air from the system The surge tank shall be equipped with a low coolant probe and sight glass to monitor the level of the coolant The surge tank shall have a cap that meets the engine manufactures pressure requirements as well as the system design requirements All radiator tubes shall be formed from aluminized steel tubing Recirculation shields shall be installed where required to prevent heated air from reentering the cooling package and affecting performance When a center bumper compartment is installed an additional shield may be required to redirect the airflow into the coolers The charge air cooler shall be a cross flow design constructed co
122. ining ambient air with the exhaust gasses at the exhaust outlet TRANSMISSION The drive train shall include an Allison Gen IV E model EVS 3000 torque converting automatic transmission which shall include electronic controls The transmission shall feature two 2 10 bolt PTO pads located on the converter housing The transmission shall include two 2 internal oil filters and Castrol TranSynd synthetic TES 295 transmission fluid which shall be utilized in the lubrication of the EVS transmission An electronic oil level sensor shall be included with the readout located in the shift selector The Gen IV E transmission shall include prognostic diagnostic capabilities These capabilities shall include the monitoring of the fluid life filter change indication and transmission clutch maintenance The transmission gear ratios shall be Ist 3 49 1 2nd 1 86 1 3rd 1 41 1 4th 1 00 1 Sth 0 75 1 6th 0 65 1 if applicable Rev 5 03 1 TRANSMISSION MODE PROGRAMMING The transmission upon start up will automatically select a four 4 speed operation The fifth speed over drive shall be available with the activation of the mode button on the shifting pad TRANSMISSION FEATURE PROGRAMMING The EVS group package number 127 shall contain the 198 vocational package in consideration of the duty of this apparatus as a Pumper This package shall incorporate an automatic neutral with selector override This feature commands the transmissi
123. inted Trim Center Dash ABS Trim LH Dash ABS Trim RH Dash ABS Glove Cmpt MDT Prov Eng Tnl Trim Flr Mat Pwr Pnt Dash Mnt Mstr Sw 2 Aux Pwr Pnt Eng Tnl Batt Dir 2 Rr R L Step Trim Grip Strut Lwr Flex Tred Mid Interior Door Trim Painted Door Trim Customer Nameplate Cab Dr Trim Reflective 1 Vert 6 Chevron w Logo Interior Grab Handle A Pillar 11 Molded Interior Grab Handle Frt Door Horiz 9 Int Grab Handle Rr Dr Alum Window Span 30 Black Powder Coat Interior Trim Vinyl Color Gray Interior ABS Trim Color Gray Interior Floor Mat Color Gray Cab Paint Int Dr Trim Zolatone Onyx Black Dash Pnl Group 3 Pnl Switches Ctr Pnl 18 12 6 LH Switches Left Pnl 8 6 2 Switches Right Pnl 8 4 4 RH Seat Belt Warn Indv Seat Loc amp LED Display w VDR Occupancy Rollover Protection RollTek Seat Material Ballistic Seat Color Gray Red Seat Belts Seat Driver Seats Inc 4 Way Air Non ABTS Seat Back Driver Non SCBA Non ABTS Seat Mounting Driver Occupancy Rollover Protection Driver Air Susp RollTek Seat Officer Seats Inc Fixed ABTS Seat Back Officer SCBA Zico Rol Loc Seat Mounting Officer Occupancy Rollover Protection Officer Mech Elec Susp RollTek Seat RFO Location 2 R L 1203 008 1215 023 1221 009 8104 002 1273 001 1266 001 1206 011 1218 026 1224 002 8107 002 1269 101 1281 101 1311 110 1355 009 1511 001 1534 002 1103 004 1111 001 1115 002 1116 002 1503 002 1504 015 1529 004 1513
124. ir Horn Shutoff Valve Air Inlet Connection Air Inlet Location LH Lwr Frt Step Fwd Plumbing Air Inlet Conn Air Inlet Outlet Manual Conn Tru Flate Interchange 1 4 Air Tank Spacers Inboard 1 5 Rear Air Tank Mnt Any Bhd Rear Axle Parallel w Frame Wheelbase 204 0 Rear Overhang 47 0 Frame Double Channel 35 00 Width Frame Warranty Lifetime 2011 Frame Clear Area Inside Outside Rail 30 Rwd Back of Cab Frame Paint Gloss Black Frt Bumper Stainless Steel Flat Frt Bumper Extension Length 24 Frt Bumper Extension Frame Width 34 25 Frt Bumper Winch Ramsey 12 000 Ibs Air Horn 2 24 Round Hadley E Tone Air Horn Location 2 Frt Bmpr Face LH Air Horn Reservoir 1 1200 Cu In Elect Siren Speaker 1 100W Cast Products SA4301 Elec Siren Speaker Location Frt Bmpr Face RH OB Frt Bumper Tow Eyes 2 Chrome Through Cab Tilt System Cab Tilt Ctrl Receptacle Temp Cab Windshield Glass Frt Dr Pwr Glass Tint Frt Dr Automotive Green Glass Rr Dr RH Pwr Glass Tint Rr Door RH Automotive Green Glass Rr Dr LH Pwr Glass Tint Rr Door LH Automotive Green Glass Side Mid RH Fxd 16 W x 26 H Glass Tint Side Mid RH Automotive Green Glass Side Mid LH Fxd 16 W x 26 H Glass Tint Side Mid LH Automotive Green Climate Ctrl Htr Defroster Ovrhd Htr A C Tunnel Mnt Climate Ctrl Actv Device Mnt A C Condenser Location Roof Mnt Fwd Ctr A C Compressor Small Capacity 1322 002 1530 001 1327 001 1302 001 1368 002 1306 001 1337 002 1305 001 1339 001 1
125. is defined as a bidder whose reputation past performance and business and financial capabilities are such that he would be judged by the appropriate City authority to be capable of satisfying the City s needs for a specific contract or purchase order The City reserves the right to determine the low bidder either on the basis of the individual items or on the basis of all items included in its INVITATION TO BID unless otherwise expressly provided in the INVITATION TO BID The City reserves the right to accept any item or group of items of any kind and to modify or cancel in whole or in part its INVITATION TO BID The City reserves the right to determine the low bidder by durability and maintenance cost over the life of the vehicle or equipment This may be done by means of past experience or research Initial cost may not determine low bid All contracts or purchase orders issued for this award will be governed by the laws of the State of Tennessee Bidder s company name signature and date indicate that these terms and conditions have been read understood and accepted DATE BIDDER S COMPANY NAME COMPANY REPRESENTATIVE Printed Name Written Signature TELEPHONE FAX EMAIL THIS DOCUMENT MUST BE SIGNED AND RETURNED WITH BID REVISED 11 06 CITY OF ATHENS STANDARD INSURANCE REQUIREMENTS Statutory Workers Compensation Insurance a Employers Liability Bodily Injury by Accident 100 000
126. isplay a Check Washer Fluid Level message CAB DOOR HARDWARE The cab entry doors shall be equipped with exterior pull handles suitable for use while wearing firefighter gloves The handles shall be made of aluminum with a chrome plated finish The interior exit door handles shall be flush paddle type with a black finish which are incorporated into the upper door panel All cab entry doors shall include locks which are keyed alike The door locks shall be designed to prevent accidental lockout The exterior pull handles shall include a scuff plate behind the handle constructed of polished stainless steel to help protect the cab finish DOOR LOCKS Each cab entry door shall include a manually operated door lock The each door lock may be actuated from the inside of the cab by means of a red knob located on the paddle handle of the respective door or by using a TriMark key from the exterior The door locks are designed to prevent accidental lock out DOOR LOCK LH REAR CAB COMPARTMENT The left hand side rear compartment shall feature a manual door lock DOOR LOCK RH REAR CAB COMPARTMENT The right hand side rear compartment shall feature a manual door lock GRAB HANDLES The cab shall include one 1 18 00 inch knurled anti slip one piece exterior assist handle behind each cab door The grab handle shall be made of 14 gauge 304 stainless steel and be 1 25 inch diameter to enable non slip assistance with a glove
127. ive door ENGINE COMPARTMENT LIGHT There shall be an incandescent NFPA compliant light mounted under the engine tunnel for area work lighting on the engine The light shall include a polycarbonate lens a housing which is vibration welded and a bulb which shall be shock mounted for extended life The light shall activate automatically when the cab is tilted SIDE SCENE LIGHTS The side of the cab shall include two 2 Whelen model 810 scene lights one 1 each side which shall be surface mounted The Whelen lights shall offer halogen lighting with 8 to 32 degree internal optics SIDE SCENE LIGHT LOCATION The scene lighting located on the driver and officer sides of the cab shall be mounted in the upper mid forward portion of the 10 00 inch raised roof of the cab between the front and rear crew doors SIDE SCENE ACTIVATION The scene lights shall be activated by two 2 rocker switches located in the switch panel one 1 for each light REAR SCENE LIGHTS The rear of the cab shall include two 2 Whelen model 810 scene lights The Whelen lights shall be surface mounted and shall offer halogen lighting at a 32 degree angle REAR SCENE LIGHT LOCATION The rear scene lights shall be located at the top of the rear wall on both the left and right outer positions REAR SCENE LIGHT ACTIVATION The rear scene lighting shall be activated via a single rocker switch located inside the cab on the switch panel INTERIOR
128. l be provided in any area where the cover may come into contact with a painted surface The crosslay compartment shall be left open on each end 3 MONITOR DISCHARGE CENTER A 3 monitor discharge shall be provided above the pump compartment in the center The discharge piping shall extend above the pump compartment a sufficient distance to allow use of the deck gun Akron 7640 discharge valve s shall be utilized on the monitor discharge s The valve shall be manually controlled from the pump operator s position with a gear actuated handwheel control with Gear Position Indicator Kit The GPI kit shall consist of a visual indicator adjacent to the handwheel indicating the position of the valve CAPPED MONITOR DISCHARGE The monitor discharge shall be capped with a female National Pipe Thread cap for future installation of monitor assembly 1 3 4 FRONT BUMPER DISCHARGE S There shall be one 1 1 3 4 discharge s provided on the front of the apparatus BUMPER EXTENSION APRON An aluminum treadbrite apron gravelshield shall be provided in the area between the extended bumper and the chassis cab BUMPER EXTENSION HOSEWELL WITH COVER A hosewell shall be provided in the bumper extension The hosewell shall be designed to fit between the front bumper framerail extensions shall have a raised lip to help prevent water entry into the compartment The hosewell shall be maximum size using all useable space between the framerails An aluminum tr
129. l of applying and releasing the brakes An inversion valve shall be installed to provide a service brake application in the unlikely event of primary air supply loss All air reservoirs provided on the chassis shall be labeled for identification The rear axle spring brakes shall automatically apply in any situation when the air pressure falls below 25 PSI and shall include a mechanical means for releasing the spring brakes when necessary An audible alarm shall designate when the system air pressure is below 60 PSI A four 4 sensor four 4 modulator anti lock braking system ABS shall be installed on the front and rear axles in order to prevent the brakes from locking or skidding while braking during hard stops or on icy or wet surfaces This in turn shall allow the driver to maintain steering control under heavy braking and in most instances shorten the braking distance The electronic monitoring system shall incorporate diagonal circuitry which shall monitor wheel speed during braking through a sensor and tone ring on each wheel A dash mounted ABS lamp shall be provided to notify the driver of a system malfunction The ABS system shall automatically disengage the auxiliary braking system device when required The speedometer screen shall be capable of reporting all active defaults using PID SID and FMI standards Additional safety shall be accommodated through Automatic Traction Control ATC which shall be installed on the tandem rear axle The
130. lack adjusters installed on the axle which features a simple durable design offering reduced weight The automatic slack adjusters shall feature a manual adjusting nut which cannot inadvertently be backed off and threaded grease fittings for easy serviceability AIR DRYER The brake system shall include a Wabco System Saver 1200 air dryer with an integral 100 watt heater with a Metri Pack sealed connector The air dryer incorporates an internal turbo cutoff valve that closes the path between the air compressor and air dryer purge valve during the compressor unload cycle The turbo cutoff valve allows purging of moisture and contaminants without the loss of turbo boost pressure The air dryer shall be located on the right hand frame rail forward of the front wheel behind the right hand cab step FRONT BRAKE CHAMBERS The front brakes shall be provided with MGM type 30 brake chambers REAR BRAKE CHAMBERS The rear axle shall include TSE 30 36 brake chambers which shall convert the energy of compressed air into mechanical force and motion This shall actuate the brake camshaft which in turn shall operate the foundational brake mechanism forcing the brake shoes against the brake drum The TSE Type 36 brake chamber has a 36 00 square inch effective area AIR COMPRESSOR The air compressor provided for the engine shall be a Wabco SS318 single cylinder pass through drive type compressor which shall be capable of producing 18 7 CFM at 1
131. led in the air horn supply line AIR INLET CONNECTION An air connection for the shoreline air inlet shall be supplied AIR INLET LOCATION The air inlet shall be installed in the left hand side lower front step in the forward position PLUMBING AIR INLET CONNECTION The air inlet connector shall be plumbed to the air system with a check valve to prevent air from escaping through the inlet connector AIR INLET OUTLET FITTING TYPE The air connector supplied shall be a 0 25 inch size Tru Flate Interchange style manual connection which is compatible with Milton T style Myers 0 25 inch Automotive style and Parker 0 25 inch 10 Series connectors AIR TANK SPACERS There shall be spacers included with the air tank mounting The spacers shall move the air tanks 1 50 inches inward towards the center of the chassis This shall provide clearance between the air tanks and the frame for body U bolt clearance REAR AIR TANK MOUNTING If a combination of wheel base air tank quantity or other requirements necessitate the location of one or more air tanks to be mounted rear of the fuel tank these tank s will be mounted parallel to frame WHEELBASE The chassis wheelbase shall be 204 00 inches REAR OVERHANG The chassis rear overhang shall be 47 00 inches FRAME The frame shall consist of double rails running parallel to each other with cross members forming a ladder style frame The frame rails shall be f
132. lf contained breathing apparatus with all sizes of cylinders The bracket shall include four PVC coated clamping arms which securely lock the SCBA in place without damaging the cylinder wall The bracket shall also include a pull release strap which shall include a 30 00 inch nylon lanyard which activates the lever on the bracket saving the occupant from reaching behind the SCBA in order to release the bracket The nylon strap shall be located on the right side of the seat The basic bracket and clamp arms shall be made of strong yet light weight aluminum alloys Hex arms and operating levers shall be plated steel to withstand years of constant use The bracket shall allow donning of the SCBA in a fast and easy manner The seat back shall include a removable padded cover which shall be provided over the SCBA cavity SEAT MOUNTING FORWARD FACING CENTER The forward facing center seats shall be installed facing the front of the cab OCCUPANCY ROLLOVER PROTECTION FFC The forward facing center seating position shall be equipped with the RollTek Rollover Occupant Protection System SEAT FRAME FORWARD FACING The forward facing center seating positions shall include an enclosed seat frame which is located and installed on the rear wall The seat frame shall measure 42 38 inches wide X 12 38 inches high X 22 00 inches deep The seat frame shall be constructed of 5052 H32 Marine Grade 0 19 inch thick aluminum plate The seat box shall be p
133. ll extend from the front of the hosebed to the rear and then extend downward to cover the exposed rear of the bed and from the left side to the right side of the hosebed The cover shall have a double reinforced area where the cover comes into contact with the upper rear corners of the hosebed dividers The cover shall be secured to the apparatus using velcro on the sides and lift dots on front The rear of the cover shall be secured to the apparatus using positive mechanical latches BULKHEAD HOSEBED DIVIDER DUNNAGE COMPARTMENT A bulkhead divider shall be provided in the front area of the hosebed separating the hosebed from the tank fill tower s The balance of this area that is not occupied by fill tower or other mounted equipment shall be used as a dunnage compartment HOSEBED COVER RED The hosebed cover shall be red LADDER COMPARTMENT ABOVE TANK BELOW HOSEBED A compartment shall be provided above the tank and below the hosebed for storing ladders and pike poles A full width drop down hinged aluminum treadbrite door shall be provided on the rear The pike pole storage shall be to the left of the ladder area 26 The compartment shall ave a single 5 diameter Signal Stat model 77 570 light mounted on the left wall of the compartment with automatic door switch The light shall be incorporated into the Door Ajar warning system in the cab Ladders All ladders shall have individual 1 8 aluminum slides lined with Rodex slip blocks
134. lled in a chrome bezel outboard of the front warning and headlamps HEADLIGHT LOCATION The headlights shall be located on the front fascia of the cab directly below the front warning lights SIDE TURN MARKER LIGHTS The sides of the cab shall include 2 LED round side marker lights which shall be provided just behind the front cab radius corners MARKER AND ICC LIGHTS In accordance with FMVSS there shall be five 5 cab LED marker lamps designating identification center and clearance provided These lights shall be installed on the face of the cab within full view of other vehicles from ground level HEADLIGHT AND MARKER LIGHT ACTIVATION The headlights and marker lights shall be controlled through a rocker switch within easy reach of the driver There shall be a dimmer switch within easy reach of the driver to adjust the brightness of the dash lights GROUND LIGHTS Each door shall include an incandescent NFPA compliant ground light mounted to the under side of the cab step below each door Each light shall include a polycarbonate lens a housing which is vibration welded and a bulb which shall be shock mounted for extended life The ground lighting shall be activated by the opening of the respective door as well as being activated when the parking brake is set STEP LIGHTS The middle step located at each door shall include a 4 00 inch round incandescent light which shall activate with the opening of the respect
135. located in the middle position and the left fill port located in the rearward position on the fuel tank FRONT AXLE The front axle shall be a Meritor Easy Steer Non drive front axle model number MFS 20 The axle shall include a 3 74 inch drop and a 71 00 inch king pin intersection KPI The axle shall include a conventional style hub with a standard knuckle FRONT AXLE WARRANTY The front axle shall be warranted by Meritor for two 2 years with unlimited miles under the general service application Details of the Meritor warranty are provided on the PDF document attached to this option FRONT WHEEL BEARING LUBRICATION The front axle wheel bearings shall be lubricated with oil The oil level can be visually checked via clear inspection windows in the front axle hubs FRONT SHOCK ABSORBERS Two 2 Bilstein inert nitrogen gas filled shock absorbers shall be provided and installed as part of the front suspension system The shocks shall be a monotubular design and fabricated using a special extrusion method utilizing a single blank of steel without a welded seam achieving an extremely tight peak to valley tolerance and maintains consistent wall thickness The monotubular design shall provide superior strength while maximizing heat dissipation and shock life The ride afforded through the use of a gas shock is more consistent and shall not deteriorate with heat the same way a conventional oil filled hydraulic shock would
136. location specific to the customer s needs The siren shall feature hands free mode and will be in standby mode awaiting instruction The siren shall offer radio broadcast public address wail yelp or piercer tones and hands free operation which shall allow the operator to turn the siren on and off from the horn ring if a horn siren selector switch option is also selected HORN BUTTON SELECTOR SWITCH A rocker switch shall be installed in the switch panel between the driver and officer to allow control of either the electric horn or the air horn from the steering wheel horn button The electric horn shall sound by default when the selector switch is in either position to meet FMCSA requirements AIR HORN ACTIVATION The air horn activation shall be accomplished by the steering wheel horn button for the driver and a right hand side Linemaster model SP491 S81 foot switch for the officer An air horn activation circuit shall be provided to the chassis harness pump panel harness connector BACK UP ALARM An ECCO model 575 backup alarm shall be installed at the rear of the chassis with an output level of 107 dB The alarm shall automatically activate when the transmission is placed in reverse INSTRUMENTATION An ergonomically designed instrument panel shall be provided The gauges shall be backlit with red LED lamps All gauges shall be driven by stepper motor movements The instrumentation system shall be multiplexed and shall
137. low the use of water from the discharge side of the pump to assist in cooling the engine COOLANT HOSES The cooling systems hose shall be formed silicone hose and formed aluminized steel tubing and include stainless steel constant torque band clamps ENGINE AIR INTAKE The engine air intake system shall include an ember separator air intake filter which shall be located in the front of the cab behind the right hand side fascia This filter shall protect the downstream air filter from embers using a combination of unique flat and crimped metal screens constructed into a corrosion resistant steel frame This multilayered screen shall be designed to trap embers or allow them to burn out before passing through the pack while creating only minimal air flow restriction through the system Periodic cleaning or replacement of the screen shall be all that is required after installation The engine shall also include an air intake filter which shall be bolted to the frame and located under the front of the cab on the right hand side The dry type filter shall ensure dust and debris safely contained inside the disposable housing eliminating the chance of contaminating the air intake system during air filter service via a leak tight seal The air flow distribution and dust loading shall be uniform throughout the high performance filter cone pack which shall result in pressure differential for improved horsepower and fuel economy The air intake shall
138. lted to the top of the compartments and masked off during the paint process is not acceptable The back side of the aluminum treadbrite shall be fully covered with a high temperature polyurethane based sealer to prevent dis similiar metal oxidation ROLL UP COMPARTMENT DOORS For all compartments requiring roll up doors The doors shall be constructed of auminum extrusion slats All doors shall be fitted with a flexible watertight seal between the slats at pivoting joints Each slat shall be individually removable for replacement in the event of damage The endcaps and rollers shall be manufactured of type 6 nylon The doors shall have a pre tension operator in a sealed alloy drum that is positioned in the upper front portion of the compartment providing maximum clearance and head room in the upper portion of the compartment Each door shall have a full door width lift bar latching handle which shall be spring loaded with two 2 surface mounted latch points mounted one 1 on each end The door shall be reinforced and the latch point with a ledge surface above the lift bar designed to provide a push surface when closing Each door shall be provided with seals made of extruded neoprene which are shaped to readily shed water The side seals are mounted in a special extrusion forward of the curtain track Driprails shall be provided above all doors STAINLESS STEEL COATED FASTENERS All fasteners used in the finish construction of the apparatu
139. ludes an air filled bag across the driver s and passenger s side windows which shall protect and cushion the head and neck of the occupant thereby reducing movement and the chance of head contact with the side of the vehicle The inflatable curtain shall be applicable on all seats adjacent to the cab side excluding theatre flip up style seating System Components Shall Include Integrated Roll Sensor IRS detects an imminent rollover activates protective devices and records crash events Integrated Belt Pretension IBP device not available with air suspension seats tightens the seat belt around occupant securing occupant in seat and positions occupant for contact with integrated head cushion Seat Pull down System S48 air suspension seats only locks seat to lowest position increases survivable space tightens belt around occupant secures occupant in seat and positions occupant for contact with integrated head cushion Inflatable Head Cushion IHC protects head neck and shields occupant from dangerous surfaces Remains inflated for 8 10 seconds This device shall affect the driver officer and adjacent seats to cab side excluding theatre flip up style seating SEAT MATERIAL The seats shall include a covering of high strength wear resistant fabric made of durable ballistic polyester A PVC coating shall be bonded to the back side of the material to help protect the seats from UV rays and from being saturated or contaminated by
140. lush latch The fuel fill shall be properly vented FRONT REAR MUDFLAPS Heavy duty black rubber mudflaps shall be provided on the front and rear wheels The mudflaps shall be attached to the apparatus in the front and the rear wheel well area using heavy duty stainless steel retention straps that are secured into place using stainless steel fasteners FRONT REAR AXLE NUT COVERS AND BABY MOONS The front and rear axle shall have stainless steel nut covers and baby moons REAR PULLING EYES Two rear 3 4 CRS pulling eyes shall be provided under the rear tailboard The eyes shall have a minimum of a 3 clear opening for passing chains through the eye AS BUILT APPARATUS BODY OWNERS MANUAL CD 2 Two as built apparatus body owners manual CD s compact disc shall be provided with the apparatus All apparatus body electrical schematics shall be provided as well as all instructional and maintenance manuals on components provided and permanently mounted on the apparatus A copy of the final apparatus body build specifications shall also be included on the CD The CD s shall be read only and shall not allow modification To eliminate component confusion generic CD s with equipment that is not provided on the apparatus body shall not be acceptable 2 LB BAG OF FASTENERS A 2 lb bag of fasteners as used in the final assembly of the apparatus shall be provided 48 DUO SAFETY 6FP 6 FIBERGLASS PIKE POLE There shall be one 1 Duo
141. meter studs A steel safety channel assembly shall be installed on the right side cab lift cylinder to prevent accidental cab lowering The safety channel assembly shall fall over the lift cylinder when the cab is in the fully tilted position A cable release system shall also be provided to retract the safety channel assembly from the lift cylinder to allow the lowering of the cab CAB TILT CONTROL RECEPTACLE The cab tilt control cable shall include a receptacle which shall be temporarily located on the right hand chassis rail rear of the cab to provide a place to plug in the cab tilt remote control pendant The tilt pump shall include 8 00 feet of cable with a six 6 pin Deutsch receptacle with a cap The remote control pendant shall include 20 00 feet of cable with a mating Deutsch connector The remote control pendant shall be shipped loose with the chassis CAB WINDSHIELD The cab windshield shall have a surface area of 2825 00 square inches and be of a two 2 piece wraparound design for maximum visibility The glass utilized for the windshield shall include standard automotive tint The left and right windshield shall be fully interchangeable thereby minimizing stocking and replacement costs Each windshield shall be installed using black self locking window rubber GLASS FRONT DOOR The front cab doors shall include a window which is 27 00 inches in width X 26 00 inches in height These windows shall have the capability t
142. mmability of materials used in the occupant compartments of motor vehicles as outlined in FMVSS 302 of which decides the burning rate of materials in the occupant compartments of motor vehicles SEAT BACK REAR FACING OUTER The rear facing outboard seat back shall include a Ziamatic brand Rol Loc mechanical self contained breathing apparatus SCBA bracket The Positive Locking Mechanical walk away bracket shall meet NFPA 1901 03 9G dynamic requirements for cylinder restraint systems for use in crew compartments of fire truck cabs The bracket shall be third Party tested to ten 10 times the force of gravity The bracket shall secure a self contained breathing apparatus with all sizes of cylinders The bracket shall include four PVC coated clamping arms which securely lock the SCBA in place without damaging the cylinder wall The bracket shall also include a pull release strap with a T handle which activates the lever on the bracket saving the occupant from reaching behind the SCBA in order to release the bracket The handle shall be located on the front of the seat in the center The basic bracket and clamp arms shall be made of strong yet light weight aluminum alloys Hex arms and operating levers shall be plated steel to withstand years of constant use The bracket shall allow donning of the SCBA in a fast and easy manner The seat back shall include a removable padded cover which shall be provided over the SCBA cavity SEAT MOU
143. mp and engine to be displayed with the push of a button It shall monitor inputs and support audible and visual warning alarms for the following conditions High Battery Voltage Low Battery Voltage Engine Off Low Battery Voltage Engine Running High Transmission Temperature Low Engine Oil Pressure High Engine Coolant Temperature Out of Water visual alarm only No Engine Response visual alarm only The program features shall be accessed via push buttons located on the front of the control panel There shall be an USB port located at the rear of the control module to upload future firmware enhancements Inputs to the control panel from the pump discharge and intake pressure sensors shall be electrical The discharge pressure display shall show pressures from 0 to 600 psi The intake pressure display shall show pressures from 30 in Hg to 600 psi The governor shall operate in two control modes pressure and RPM No discharge pressure or engine RPM variation shall occur when switching between modes A throttle ready LED shall light when the interlock signal is recognized The governor shall start in pressure mode and set the engine RPM to idle In pressure mode the governor shall automatically regulate the discharge pressure at the level set by the operator In RPM mode the governor shall maintain the engine RPM at the level set by the operator except in the event of a discharge pressure increase The governor shall limit a discharge pres
144. mp transmission to allow true separation of the transmission from the pump without disassembly of either component No sleeve type bearings shall be used The pump transmission shall be rigidly attached to the pump body assembly and be of the latest design incorporating a high strength involute tooth form Hy Vo chain drive and driven sprockets capable of operating at high speeds to provide smooth quiet transfer of power The pump gear ratio shall be selected by the apparatus manufacturer to give the maximum performance with the engine and transmission selected IMPELLER FLAME PLATE The impeller shall be bronze with double suction inlets accurately balances mechanically and hydraulically of the mixed flow design with reverse flow labyrinth type wear rings that resist water bypass and loss of efficiency due to wear The impeller shall have a Flame Plated Hub to assure maximum pump life and efficiency despite the presence of abrasive particles such as fine sand in the water being pumped Wear rings to be bronze and shall be easily replaceable to restore pump efficiency and eliminate the need to replace the entire pump casing due to wear MECHANICAL SEAL The pump shaft shall have face type self adjusting corrosion and wear resistant mechanical seals PRESSURE GOVERNOR MONITORING and MASTER PRESSURE DISPLAY Fire Research InControl series TGA300 pressure governor and monitoring display kit shall be installed The kit shall includ
145. mplement a self calibrating pressure sensor system to indicate the tank volume A probe type of system shall not be used DISCHARGE PRESSURE GAUGES SPAN THUEMLING Unless otherwise specified each 1 1 2 or larger discharge shall have a SPAN THUEMLING model FA fire apparaus quality pressure gauge The guage shall be glycerin filled 40F to 150F read from O 400 psi be accurate within 1 and havea high impact resistant clear acrylic The gauges shall be equipped a KEM X freezeproof isolator protection 2 1 2 DIAMETER DISCHARGE PRESSURE GAUGES The individual discharge pressure gauges shall have a 2 1 2 diameter dial COLOR CODED DISCHARGE PRESSURE GAUGE BEZELS 15 The discharge pressure gauges shall have color coded bezels matching their identification labels DISCHARGE PRESSURE GAUGE DIALS WHITE FACE The discharge pressure gauge dials shall be white with black markings The needle shall match the color of the markings with a bright colored tip DISCHARGE PRESSURE GAUGES CONTROL HANDLE ALIGNMENT The pressure gauge shall be directly in line with the discharge control handle for the discharge that they provide pressure readout for For ease of operation this requirement must be strictly adhered to There shall be no exception to this requirement DISCHARGE PRESSURE GAUGE LABELING The gauges shall be clearly labeled with permanent color coded labels PRESSURE GAUGE WARRANTY The discharge pressure gauges shall ha
146. mpletely of aluminum with welded side tanks The charge air cooler shall have a minimum of a 390 square inch core and be bolted to the top of the radiator to allow a single depth core thus allowing a more efficient and serviceable cooling system All charge air cooler tubes shall be formed from aluminized steel tubing and installed with silicone hump hoses and stainless steel constant torque style clamps meeting the engine manufactures requirements ENGINE COOLANT The cooling package shall include Extended Life Coolant ELC The use of ELC provides longer intervals between coolant changes over standard coolants providing improved performance The coolant shall contain a 50 50 mix of ethylene glycol and de ionized water to keep the coolant from freezing to a temperature of 34 degrees F Proposals offering supplemental coolant additives SCA shall not be considered as this is part of the extended life coolant makeup ELECTRONIC COOLANT LEVEL INDICATOR The instrument panel shall feature a low engine coolant indicator light which shall be located in the center of the instrument panel An audible tone alarm shall also be provided to warn of a low coolant incident ENGINE PUMP HEAT EXCHANGER A single bundle type coolant to water heat exchanger shall be installed between the engine and the radiator The heat exchanger shall be designed to prohibit water from the pump from coming in contact with the engine coolant This shall al
147. multaneous forward load of 3000 pounds each on the lap and shoulder belts and twenty 20 times the weight through the center of gravity This model of seat installed in the cab model as specified shall have successfully completed the dynamic sled testing using FMVSS 208 as a guide with the following accommodations In order to reflect the larger size outfitted firefighters the test dummy used shall be a 95th percentile hybrid HI male weighing 225 pounds rather than the 50th percentile male dummy weighing 165 pounds as referenced in FMVSS 208 The materials used in construction of the seat shall also have successfully completed testing with regard to the flammability of materials used in the occupant compartments of motor vehicles as outlined in FMVSS 302 of which dictates the allowable burning rate of materials in the occupant compartments of motor vehicles SEAT BACK DRIVER The driver s seat shall feature a two 2 way adjustable lumbar support and offer an infinite fully reclining adjustable titling seat back The seat back shall also feature a contoured head rest OCCUPANCY ROLLOVER PROTECTION DRIVER The driver s position shall be equipped with the RollTek Rollover Occupant Protection System SEAT OFFICER The officer s seat shall be a Seats Inc 911 ABTS series The seat shall feature a tapered and padded seat and cushion The seat shall be a non adjustable type seat The seat shall feature an all belts to seat ABTS
148. ndicator wrench symbol on the digital display between the selected and attained indicators The prognostics monitor various operating parameters to determine and shall alert you when a specific maintenance function is required TRANSMISSION PRE SELECT WITH AUXILIARY BRAKE When the auxiliary brake is engaged the transmission shall automatically shift to second gear to decrease the rate of speed assisting the secondary braking system and slowing the vehicle TRANSMISSION COOLING SYSTEM The transmission shall include an air to oil cooler integrated into the lower portion of cooling package The transmission cooling system shall meet all transmission manufacturer requirements The cooling system shall feature a circuit provision located within the hydraulic transmission oil which shall provide for rapid warm up to the optimum transmission operating temperature TRANSMISSION WARRANTY The Allison EVS series transmission shall be warranted for a period of five 5 years with unlimited mileage Parts and labor shall be included in the warranty DRIVELINE All drivelines shall be heavy duty metal tube and equipped with Spicer 1710 series universal joints The shafts shall be dynamically balanced prior to installation to alleviate future vibration In areas of the driveline where a slip shaft is required the splined slip joint shall be coated with Glide Coat MIDSHIP PUMP GEARBOX A temporary jackshaft driveline shall be install
149. nditions ALL GREEN Tire is properly inflated HALF GREEN HALF RED Tire is approximately 10 under inflated ALL RED Tire is 20 or more under inflated LETTERING The Apparatus Dealer shall provide and apply all vehicle lettering and numbering NFPA REFLECTIVE STRIPE DEALER SUPPLIED INSTALLED The reflective stripe necessary on the sides front and rear of the apparatus shall be provided and applied by the Apparatus Dealer REAR CHEVRON STRIPING DIAMOND GRADE A minimum of 50 percent of the rear vertical surface of the apparatus shall be be covered with 6 inch alternating 983 71 47 red and 983 23 fluorescent yellow green Diamond grade retroreflective striping The striping shall slop downward away from the centerline of the apparatus at a 45 degree angle The retroreflective material shall conform to the requirements of ASTM D 4956 Standard Specification for Retroreflective Sheeting for Traffic Control Type or better ENGINE EXHAUST The exhaust pipe from the engine shall be ahead of the rear wheels A shield shall be provided between the apparatus body and the exhaust pipe if necessary to deflect heat away from the body The exhaust system shall be designed and installed by the chassis manufacturer to comply with EPA equipment requirements FUEL FILL The chassis fuel fill shall be located in the driver s side rear wheel cowel The fill shall be located behind a highly polished stainless steel hinged door with f
150. ned breathing apparatus SCBA bracket The Positive Locking Mechanical walk away bracket shall meet NFPA 1901 03 9G dynamic requirements for cylinder restraint systems for use in crew compartments of fire truck cabs The bracket shall be third Party tested to ten 10 times the force of gravity The bracket shall secure a self contained breathing apparatus with all sizes of cylinders The bracket shall include four PVC coated clamping arms which securely lock the SCBA in place without damaging the cylinder wall The bracket shall also include a pull release strap which shall include a 30 00 inch nylon lanyard which activates the lever on the bracket saving the occupant from reaching behind the SCBA in order to release the bracket The nylon strap shall be located on the right side of the seat The basic bracket and clamp arms shall be made of strong yet light weight aluminum alloys Hex arms and operating levers shall be plated steel to withstand years of constant use The bracket shall allow donning of the SCBA in a fast and easy manner The seat back shall include a removable padded cover which shall be provided over the SCBA cavity OCCUPANCY ROLLOVER PROTECTION OFFICER The officer s position shall be equipped with the RollTek Rollover Occupant Protection System SEAT REAR FACING OUTER LOCATION The crew area shall include two 2 rear facing crew seats which include one 1 located directly behind the driver seat and one 1 lo
151. neered for a long life REAR WHEEL The rear wheels shall be Accuride hub piloted heavy duty 22 50 inch x 8 25 inch aluminum wheels Each outer wheel shall have a polished aluminum finish on the exterior surface and each inner wheel shall have a machine finish The wheels shall be forged from a single piece of aluminum which shall be corrosion resistant engineered to be lightweight and provide exceptional performance The hub piloted mounting system shall provide easy installation and shall include two piece flange nuts WHEEL TRIM The front wheels shall include stainless steel lug nut covers and stainless steel baby moons shipped loose with the chassis for installation by the apparatus builder The baby moons shall have cutouts for oil seal viewing when applicable The rear wheels shall include stainless steel lug nut covers and band mounted spring clip stainless steel high hats shipped loose with the chassis for installation by the apparatus builder The lug nut covers baby moons and high hats shall be RealWheels brand constructed of 304L grade non corrosive stainless steel with a mirror finish Each wheel trim component shall meet D O T certification BRAKE SYSTEM A rapid build up air brake system shall be provided The air brakes shall include a two 2 air tank three 3 reservoir system with a total of 4152 cubic inch of air capacity A floor mounted treadle valve shall be mounted inside the cab for graduated contro
152. ng closed cell foam with a 0 06 inch thick non slip vinyl surface with a pebble grain finish The covering shall be held in place by a pressure sensitive adhesive and aluminum trim molding All exposed seams shall be sealed with silicone caulk matching the color of the floor mat to reduce the chance of moisture and debris retention INTERIOR TRIM VINYL The cab interior shall include trim on the front and rear crew ceiling the cab walls and the rear wall of the cab The trim shall be constructed of insulated vinyl over a hard board backing The trim shall be securely fastened to the interior of the cab utilizing snap style fasteners with a decorative cover for a more appealing appearance REAR WALL INTERIOR TRIM The rear wall of the cab shall be trimmed with vinyl HEADER TRIM The cab interior shall include the header above the driver and officer positions which shall be constructed of vacuum formed ABS panel INTERIOR TRIM SUN VISOR The header shall include two 2 7 00 inches high X 18 00 inches wide impact resistant transparent acrylic polycarbonate sun visors with a smoke gray tint shall be provided and installed on the header above the driver and officer The see thru visors are designed for maximum flexibility of positioning utilizing an arm with virtually unlimited adjustability with 13 50 inch long lateral travel of the tinted visor at the end of the arm which can be locked in place by a thumbscrew The visors a
153. ngth and rigidity to the cab as well as additional roll over protection The cab side walls and lower roof skin shall be 0 13 inch thick the rear wall and raised roof skins shall be 0 09 inch thick the front cab structure shall be 0 19 inch thick The exterior width of the cab shall be 94 00 inches wide with a minimum interior width of 88 00 inches The overall cab length shall be 148 00 inches with 74 00 inches from the centerline of the front of the axle to the back of the cab The cab interior shall be designed to afford the maximum usable interior space and attention to ergonomics with hip and legroom while seated which exceeds industry standards The crew cab floor shall be flat across the entire walking area for ease of movement inside the cab The cab shall offer an interior height of 58 00 inches from the front floor to the headliner in the non raised roof area and a rear floor to headliner height of 65 00 inches in the raised roof area at a minimum The cab shall offer an interior measurement at the floor level from the rear of the engine tunnel to the rear wall of the cab of 58 50 inches All interior measurements shall include the area within the interior trimmed surfaces and not to any unfinished surface The cab shall include a driver and officer area with two 2 cab doors large enough for personnel in full firefighting gear The front doors shall offer a clear opening of 40 00 inches wide X 53 50 inches high from the cab floor to t
154. nt manufacturer shall also perform an annual audit of the paint process 46 PPG CERTIFIED 10 YEAR PAINT WARRANTY The apparatus body exterior finish paint shall have a 10 year warranty per the terms and conditions of the PPG written warranty The warranty shall be certified by the manufacturer of the paint Documentation of this shall be provided Any warranty that is extended by the apparatus manufacturer and not backed by the paint manufacturer will not be acceptable ELECTROLYSIS CORROSION CONTROL The apparatus shall be assembled using ECK or electrolysis corrosion control on all high corrosion potential areas such as door latches door hinges trim plates fenderettes etc This coating is a high zinc compound that shall act as a sacrificial barrier to prevent electrolysis and corrosion between dissimilar metals This shall be in addition to any other barrier material that may be used APPARATUS BODY UNDERCOATING The apparatus body shall be undercoated after assembly is completed A bituminous based automotive type undercoat shall be used Care shall be taken to avoid undercoat application to items that would hinder normal maintenance THERMOPLASTIC APPARATUS BODY COMPARTMENT INTERIOR FINISH The interior of all apparatus body compartments shall be finshed with a gray thermoplastic coating TIRE PRESSURE VISUAL INDICATOR Valve stem mounted visual indicators shall be provided on each tire The indicators shall identify the following co
155. nted by the apparatus manufacturer Use of any welded light gauge less than Schedule 10 manifolding or plumbing shall not be acceptable STAINLESS STEEL PIPING WARRANTY The stainless steel piping shall be warranted to be free from corrosion perforation for a period of 10 years following the delivery of the apparatus VENTED LUG CAPS AND PLUGS All intake and discharge plugs and caps and plugs shall be vented lug type design ed to relieve trapped pressure and help reduce possible operator injuries 2 1 2 LEFT SIDE AUXILIARY INTAKE S One 1 2 1 2 auxiliary intake s shall be provided on the left side of the apparatus pump compartment The intake s shall be controlled from the pump operator s position Akron 8825 suction valve s shall be utilized on the left side 2 1 2 intake s and shall be located within the pump compartment The valve shall be manually controlled from the pump operator s position A 2 1 2 chrome plated female National Standard Thread swivel connection with screen shall be provided on the left side 2 1 2 intake s with a chrome plated male National Standard Thread intake plug with chrome plated chain A 3 4 bleeder drain valve shall be provided on the left side auxiliary intake FOAM PRO 2002 CLASS A B FOAM SYSTEM A Foam Pro model 2002 Class A B foam system shall be provided and properly installed on the apparatus The system shall be an electronic fully automatic variable speed direct injection discharge sid
156. o Pump indicator lights open compartment ground start signal park brake ground ignition signal master power customer ignition air horn solenoid switch high idle switch and high idle indication light The harness shall be designed for a side mount pump panel An apparatus interface wiring harness shall also be included which shall be wired to the cab harness interface connectors and shall incorporate circuits with relays to control pump functions This harness shall control the inputs for the transmission lock up circuits governor hand throttle controls and dash display which shall incorporate Pump Engaged and OK to Pump indicator lights The harness shall contain circuits for the apparatus builder to wire in a pump switch ENGINE PROGRAMMING REMOTE THROTTLE The engine ECM Electronic Control Module discreet wire remote throttle circuit shall be turned off for use with a J1939 based pump controller or when the discreet wire remote throttle controls are not required ENGINE PROGRAMMING IDLE SPEED The engine low idle speed will be programmed at 700 rpm ENGINE FAN DRIVE The engine cooling system fan shall incorporate a thermostatically controlled Horton clutched type fan drive When the clutched fan is disengaged it shall facilitate improved vehicle performance cab heating in cold climates and fuel economy The fan clutch design shall be fail safe so that if the clutch drive fails the fan shall engage to
157. o roll down completely into the door housing This shall be accomplished using electric actuation The power window shall be controlled with a switch on the driver s door There shall be an irregular shaped fixed window which shall measure 2 50 inches wide at the top 8 00 inches wide at the bottom X 26 00 inches in height more commonly known as cozy glass ahead of the front door roll down windows The windows shall be mounted within the frame of the front doors trimmed with a black anodized ring on the exterior GLASS TINT FRONT DOOR The windows located in the left and right front doors shall have a standard green automotive tint which shall allow seventy five percent 75 light transmittance GLASS REAR DOOR RH The rear right hand side crew door shall include a window which is 27 00 inches in width X 26 00 inches in height The window shall be a powered type and shall be controlled by a switch on the inner door panel and on the driver s door panel GLASS TINT REAR DOOR RIGHT HAND The window located in the right hand side rear door shall include a standard green automotive tint which shall allow seventy five percent 75 light transmittance GLASS REAR DOOR LH The rear left hand side crew door shall include a window which is 27 00 inches in width X 26 00 inches in height The window shall be a powered type and shall be controlled by a switch on the inner door panel and on the driver s door panel GLASS
158. om the apparatus body a maximum of 1 The fenderette must be bolted into place and removable for replacement 100 BODY WIDTH The apparatus body shall be 100 wide from side to side measuring from the rub rail mounting surface COMPARTMENT VENTILATION Each compartment shall have a removable ventilation plate to allow for air movement inthe compartment A cleanable filter material shall be provided behind the plate 21 FRONT COMPARTMENT FACE OVERLAY The vertical surface of the front compartment face shall be overlaid with fire apparatus quality alu minum treadbrite The overlay shall be one piece construction from top to bottom The alumi num treadbrite shall be an overlay only and shall not form any structural part of the apparatus It shall be fitted on the apparatus body with all holes drilled prior to painting Aluminum treadbrite that is welded or bolted to the front face of the apparatus and masked off during the paint process is not acceptable The back side of the aluminum treadbrite shall be fully covered with a high temperature polyurethane based sealer to prevent dissimilar metal oxidation COMPARTMENT TOP OVERLAY The compartment tops shall be overlaid with fire apparatus quality aluminum treadbrite The alu minum treadbrite shall be an overlay only and shall not form any structural part of the apparatus It shall be fitted on the apparatus body with all holes drilled prior to painting Aluminum treadbrite that is welded or bo
159. on An Akron Slo Clozing mechanism shall be implemented in the control mechanism The right side 3 discharge s shall extend straight out of the apparatus with no type of elbow A 3 FNST x 5 locking Storz elbow adapter shall be provided on the right side 3 discharge s with a 5 blind cap and chain LEFT 2 1 2 DISCHARGE S Two 2 2 1 2 discharge s shall be provided on the left side of the apparatus Akron 8825 series discharge valve s shall be utilized on the left side 2 1 2 discharge s The valve shall be manually controlled from the pump operator s position The left side 2 1 2 discharge s shall have chrome discharge elbows that are cast as an integral part of the valve A 2 1 2 chrome plated National Standard Thread discharge cap shall be provided on the left side 2 1 2 discharge s with a chrome plated chain LEFT REAR 2 1 2 DISCHARGE One 1 2 1 2 discharge shall be provided on the left rear of the apparatus Akron 8825 series discharge valve s shall be utilized on the left rear 2 1 2 discharge s The valve shall be manually controlled from the pump operator s position The left rear 2 1 2 discharge s shall have chrome discharge elbow s A 2 1 2 chrome plated National Standard Thread discharge cap shall be provided on the left rear 2 1 2 discharge s with a chrome plated chain 1 3 4 CROSSLAY PRECONNECTS Two 1 3 4 preconnected crosslays shall be provided and located above the side mount pump panel
160. on the engine oil pressure gauge shall read from 0 to 140 pounds per square inch PSI The engine oil pressure scale shall be non linear to expand the scale in the region of normal operation A red indicator light in the gauge shall indicate low engine oil pressure The scale on the coolant temperature gauge shall read from 160 to 250 degrees Fahrenheit F A red indicator light in the gauge shall indicate high coolant temperature The scale on the transmission oil temperature gauge shall read from 100 to 300 degrees Fahrenheit F A red indicator light in the gauge shall indicate high transmission oil temperature The scale on the voltmeter shall read from 8 to 16 volts A red indicator light shall indicate high or low system voltage The instrument panel shall contain an Enunciator Module that contains the following indicator lights All indicator lights shall contain LED lamps RED LAMPS Stop Engine indicates critical engine fault 5 Park Brake indicates park brake is set Volts indicates high or low system voltage 4 Low Oil Press indicates low engine oil pressure 4 High Coolant Temp indicates excessive engine coolant temperature 4 High Trans Temp indicates excessive transmission oil temperature 4 Low Air indicates low air pressure in either system one or system two 4 Low Coolant Level indicates low engine coolant level 1 5 Air Filter indicates excessive engine air intake restriction 5 Brake Sy
161. on to neutral when the park brake is applied regardless of drive range requested on the shift selector This requires re selecting drive range to shift out of neutral for the override This package shall be coupled with the use of a split shaft PTO and incorporate pumping circuits These circuits shall be used allowing the vehicle to operate in the fourth range lockup while operating the pump mode due to the 1 to 1 ratio through the transmission therefore the output speed of the engine is the input speed to the pump The pump output can be easily calculated by using this input speed and the drive ratio of the pump itself to rate the gallons of water the pump can provide An eight 8 pin Delphi connector will be provided next to the steering column connector This will contain the following input output circuits to the transmission control module Function ID Description Wire assignment C PTO Request 142 J Fire Truck Pump Mode 4th Lockup 122 123 C Range Indicator 145 4th G PTO Enable Output 130 Signal Return 103 ELECTRONIC TRANSMISSION OIL LEVEL INDICATOR The transmission fluid shall be monitored electronically and shall send a signal to activate a warning in the instrument panel when levels fall below normal TRANSMISSION SHIFT SELECTOR An Allison pressure sensitive range selector touch pad shall be provided and located to the right of the driver within clear view and easy reach The shift selector shall provide a prognostic i
162. ormed in the shape of a C channel with the outer rail measuring 10 25 inches high X 3 50 inches deep upper and lower flanges X 0 38 inches thick with an inner channel of 9 44 inches high X 3 13 inches deep and 0 38 inches thick Each rail shall be constructed of 110 000 psi minimum yield high strength low alloy steel Each double rail section shall be rated by a Resistance Bending Moment RBM minimum of 3 213 100 inch pounds and have a minimum section modulus of 29 21 cubic inches The frame shall measure 35 00 inches in width Proposals calculating the frame strength using the box method shall not be considered Proposals including heat treated rails shall not be considered Heat treating frame rails produces rails that are not uniform in their mechanical properties throughout the length of the rail Rails made of high strength low alloy steel are already at the required yield strength prior to forming the rail A minimum of seven 7 fully gusseted 0 25 inch thick cross members shall be installed The inclusion of the body mounting or bumper mounting shall not be considered as a cross member The cross members shall be attached using zinc coated grade 8 fasteners The head bolts shall be flanged type with distorted threads held in place by flanged lock nuts Each cross member shall be mounted to the frame rails utilizing a minimum of 0 25 inch thick gusset reinforcement plates at all corners balancing the area of force throughout the entire
163. ose is to combat structural and associated fires VEHICLE TYPE The chassis shall be manufactured for use as a straight truck type vehicle and designed for the installation of a permanently mounted apparatus behind the cab The apparatus of the vehicle shall be supplied and installed by the apparatus manufacturer AXLE CONFIGURATION The chassis shall feature a 4 X 2 axle configuration consisting of a single rear drive axle with a single front steer axle GROSS AXLE WEIGHT RATINGS FRONT The front gross axle weight rating GAWR of the chassis shall be 20 000 pounds This front gross axle weight rating shall be adequate to carry the weight of the completed apparatus including all equipment and personnel GROSS AXLE WEIGHT RATINGS REAR The rear gross axle weight rating GAWR of the chassis shall be 27 000 pounds This rear gross axle weight rating shall be adequate to carry the weight of the completed apparatus including all equipment and personnel PUMP PROVISION The chassis shall include provisions to mount a drive line pump in the middle of the chassis behind the cab more commonly known as the midship location CAB STYLE The cab shall be a custom fully enclosed ELFD model with a 10 00 inch raised roof over the driver officer and crew area designed and built specifically for use as an emergency response vehicle by a company specializing in cab and chassis design for all emergency response applications Th
164. ough the tank and shall be piped behind the rear wheels to maximize traction 1 TANK SUMP DRAIN A 1 drain shall be provided in the bottom of the tank sump to fully drain the tank The drain shall use 1 stainless steel 17 piping with a 1 valve The control for the valve shall be remoted to the drivers side of the apparatus just under and behind the side rubrail The drain control handle shall be labeled TANK DRAIN 10 GALLON CLASS A FOAM TANK A 10 gallon Class A foam tank shall be provided The tank shall have all connections necessary to connect to the foam system and shall also have a 1 4 turn drain valve with hose attached to allow the tank to be drained The tank shall have a 8 x 8 fill tower with hinged type lid with latch A vent shall be provided in the lid A label shall be provided on the lid that reads CLASS A FOAM TANK FILL and WARNING DO NOT MIX BRANDS AND TYPES OF FOAM 7 x 10 lid CLASS A FOAM TANK BOOSTER TANK INTEGRATION The class A foam tank shall be integrated into the apparatus booster tank The A foam tank shall not be separate from the booster tank 50 GALLON CLASS B FOAM TANK A 50 gallon Class B foam tank shall be provided The tank shall have all connections necessary to connect to the foam system and shall also have a 1 4 turn drain valve with hose attached to allow the tank to be drained The tank shall have a 8 x 8 fill tower with hinged type lid with latch A vent shall be provided in th
165. pass the entire front of the aluminum cab structure from the bottom of the windshield to the bottom of the cab and shall be the Classic design The front cab fascia shall include two 2 molded plastic modules on each side accommodating a total of up to four 4 Hi Low beam headlights and two 2 turn signal lights or up to four 4 warning lights Two 2 chrome plated molded plastic bezels shall be provided on each side around each set of two lamps FRONT GRILLE The front cab fascia shall include a classic box style polished stainless steel front grille with a Spartan logo The grille shall measure approximately 40 00 inches wide at the top of tapering to 32 00 inches wide at the bottom X 33 00 inches high X 1 50 inches deep The grille shall include a minimum free air intake of 632 90 square inches shall be installed on the front of the cab The upper portion of the grille shall be hinged at the bottom so it can be opened to allow easy access for examination of the windshield wiper motor linkage and other options mounted within that area The upper portion of the grille shall be secured with two 2 flush push button latches CAB PAINT EXTERIOR The cab shall be painted prior to the installation of glass accessories and all other cab trim to ensure complete paint coverage and the maximum in corrosion protection of all metal surfaces All metal surfaces on the entire cab shall be ground by disc to remove any surface oxidation
166. per hour when properly inflated to 120 pounds per square inch The front tire US Fire Service Intermittent Usage load capacity shall be 20 000 pounds per axle with a speed rating of 65 miles per hour when properly inflated to 120 pounds per square inch REAR TIRE The rear tires shall be Michelin 12R 22 5 16PR H tubeless radial XDN2 all weather tread The rear tire stamped load capacity shall be 27 120 pounds per axle with a speed capacity of 75 miles per hour when properly inflated to 120 pounds per square inch The rear tire US Fire Service Intermittent Usage load capacity shall be 28 880 pounds per axle with a speed capacity of 75 miles per hour when properly inflated to 120 pounds per square inch REAR AXLE RATIO The rear axle ratio shall be 5 38 1 TIRE PRESSURE INDICATOR There shall be a voucher provided with the chassis for a pop up style tire pressure indicator at each tire valve stem The indicator shall provide visual indication of pressure in the specific tire The tire pressure indicators shall be redeemed upon the vehicle manufacturer s receipt of the voucher for installation by the customer FRONT WHEEL The front wheels shall be Accuride hub piloted 22 50 inch X 12 25 inch polished aluminum wheels The hub piloted mounting system shall provide easy installation and shall include two piece flange nuts The wheels shall be forged from a single piece of aluminum designed to be corrosion resistant and are engi
167. prevent engine overheating due to the fan clutch failure ENGINE COOLING SYSTEM There shall be a heavy duty aluminum cooling system designed to meet the demands of the fire industry The cooling system shall have the capacity to keep the engine properly cooled under all conditions of road and pumping operations The cooling system shall be designed and tested to meet or exceed the requirements specified by the engine and transmission manufacturer and all EPA requirements The complete cooling system shall utilize heavy duty welds and be mounted to isolate the entire system from vibration or stress The individual cores of the cooling system shall be mounted in a manner to allow expansion and contraction at various rates without inducing stress into the adjoining cores The cooling system shall be comprised of a stacked single depth package that provides the maximum cooling capacity for the specified engine as well as offers excellent serviceability The main components shall include a surge tank a charge air cooler a recirculation shield and a radiator Proposals unable to offer a stacked single depth cooling package shall not be considered There shall be a single depth core that allows greater efficiency enhanced serviceability and lighter weight with a higher ambient capability The cooling package core shall not protrude below the frame of the vehicle by more than 1 1 inch This feature shall improve the angle of approach thereby reduc
168. r 2 5 discharge FOAM PRO CLASS A B FOAM SYSTEM TANK SELECTOR VALVE There shall be a model 3435 0079 manual tank selector valve shall be provided on the side pump panel The manual valve shall have the following settings Class A foam Class B foam Off position Flush CLASS A LOW FOAM IN TANK SWITCH There shall be a Foam Pro model 2510 0032 low tank level switch provided and vertically mounted in the wall of the foam tank This switch shall provide low foam concentrate indication to the pump operator CLASS B LOW FOAM IN TANK SWITCH There shall be a Foam Pro model 2510 0032 low tank level switch provided and vertically mounted in the wall of the foam tank This switch shall provide low foam concentrate indication to the pump operator FOAM SYSTEM SCHEMATIC PLACARD FOR DUAL TANK SYSTEM There shall be a Foam Pro part number 6032 0016 foam system layout placard provided and located in close proximity to the pump operator s position as required by NFPA 1901 FOAM SYSTEM RATING PLACARD FOR FOAM PRO 2002 SYSTEM There shall be a Foam Pro part number 6032 0021 foam system rating placard be provided in close proximity to the pump operator s position as required by NFPA 1901 RIGHT 3 DISCHARGE S One 1 3 discharge shall be provided on the right side of the apparatus Akron 8630 series discharge valve s shall be utilized on the right side 3 discharge s The valve shall be manually controlled from the pump operator s positi
169. r coded burgundy LEFT SIDE INTAKE STEAMER TYPE NO VALVE The left side master intake shall be steamer type and shall not have any type of valve LEFT SIDE MASTER INTAKE CAP DELETE No type of cap shall be provided on the left side master intake 6 RIGHT PASSENGER SIDE MASTER INTAKE A 6 master intake shall be provided on the right passenger side of the apparatus The intake shall have a 6 male National Standard Thread connection The intake shall have a removable screen to prevent the entry of large objects into the pump The screen shall be constructed of a material that will provide cathodic protection to the pump A label shall be provided above the intake that states PASSENGER SIDE MASTER INTAKE The label shall be color coded burgundy RIGHT SIDE INTAKE STEAMER TYPE NO VALVE The right side master intake shall be steamer type and shall not have any type of valve RIGHT SIDE MASTER INTAKE CAP DELETE No type of cap shall be provided on the right side master intake 3 8 PUMP COOLING BYPASS LINE A 3 8 pump cooling bypass line shall be provided from the pump discharge manifold directly into the tank This discharge shall implement a Class 1 model 38BV all brass ball type 1 4 turn valve with chro me plated handle control located on the pump panel The valve control handle shall be indicate the open closed position of the valve The handle shall have a recessed area for mounting of the identification label which shall
170. re easily adjusted and can be placed into a chosen position with one hand The sun visors will help protect vehicle occupants from solar glare without obscuring their vision TRIM CENTER DASH The main center dash area shall be constructed of durable vacuum formed ABS composite TRIM LH DASH The left hand dash shall be a one 1 piece durable vacuum formed ABS composite housing which shall be custom molded for a perfect fit around the instrument panel and the lower control panels to the left and right of the steering column TRIM RH DASH The right hand dash trim shall consist of a vacuum formed ABS composite module which contains a glove compartment with a hinged locking door and a Mobile Data Terminal MDT provision The glove compartment size shall be 13 50 inches wide X 6 25 inches high X 5 50 inches deep The MDT provision shall be provided above the glove compartment ENGINE TUNNEL TRIM The cab engine tunnel shall be covered with 44 of an inch thick multi layer mat consisting of 25 inch closed cell foam 13 of an inch thick PVC acoustical barrier and 06 inch thick non slip pebble grain The engine tunnel mat shall be trimmed with anodized aluminum stair nosing trim for an aesthetically pleasing appearance POWER POINT DASH MOUNT The cab shall include two 2 12 volt cigarette lighter type receptacles in the center cab dash to provide a power source for 12 volt electrical equipment The receptacles shall be wired
171. re tank cradle sub structure shall be framed and jig welded together to insure a truly square assembly The substructure shall be fastened to the chassis rails so that it may be easily removed from the chassis for repair replacement or mounting to a new chassis After complete assembly of the tank cradle sub structure the entire assembly shall be hot dipped galvanized for superior corrosion protection Due to the extreme duty that this apparatus will experience during its intended service life and to prevent rusting and corrosion from shortening the service life of this apparatus sub frames fabricated of painted undercoated steel or aluminum tubing shall not be acceptable REAR SUPPORT STRUCTURE HOT DIPPED GALVANIZED The apparatus body substructure shall be constructed of high strength structural steel The substructure shall be designed to provide integral support of the apparatus body rear step and the tank mounting cradle system The entire sub frame shall be framed and jig welded together to insure a truly square sub frame assembly The substructure shall be fastened to the chassis rails so that the apparatus body may be easily removed from the chassis for repair replacement or mounting to a new chassis No holes shall be drilled into the top or bottom flange of the chassis frame rails The substructure shall be designed to allow for a 22 24 side running board rear step height when the apparatus is on level ground All fasteners use
172. res the vehicle s lateral acceleration The Controller Area Network CAN bus provides information on the steering angle On the basis of lateral acceleration and steering angle an integrated microcontroller calculates a theoretical angular speed for the stable vehicle condition FRONT BRAKES The front brakes shall be Meritor 16 5 x 6 S cam drum type REAR BRAKES The rear brakes shall be Meritor 16 50 inch X 7 00 inch S cam drum type The brakes shall include a cast iron shoe PARK BRAKE Upon application of the push pull valve in the cab the rear brakes will engage via mechanical spring force This is accomplished by dual chamber rear brakes satisfying the FMVSS parking brake requirements PARK BRAKE CONTROL A Meritor Wabco manual hand control push pull style valve shall operate the parking brake system The control shall be yellow in color The parking brake actuation valve shall be mounted on the left hand dash to the right of the steering column within easy reach of the driver FRONT BRAKE SLACK ADJUSTERS The front brakes shall include Meritor automatic slack adjusters shall be installed on the chassis which features a simple durable design offering reduced weight The automatic slack adjusters shall feature a manual adjusting nut which cannot inadvertently be backed off and threaded grease fittings for easy serviceability REAR BRAKE SLACK ADJUSTERS The rear brakes shall include Meritor automatic s
173. s body shall be marine grade stainless steel Fasteners that pass through an aluminum panel shall be Magna Gard or equal coated to help prevent dissimilar metal reaction and corrosion As the Magna Gard or equal coating is a baked on type coating providing for excellent adhesion to the fastener spray on type coatings may be used in conjunction with the Magna Gard or equal but not in place of it As dissimilar metal corrosion is a common occurrence on all apparatus and the Magna Gard or similiar baked on finishes coated fasteners are commercially available to all manufacturer s and is not a proprietary product there shall be no exception to this requirement DRIVER S SIDE COMPARTMENT IN FRONT OF THE REAR WHEELS A compartment shall be provided in front of the rear wheels The compartment shall be 64 high x 48 75 wide x 26 22 usable depth the full height of the compartment The compartment shall have a roll up door with an opening 58 high x 42 wide The roll up door shall have a brushed satin finish DRIVER S SIDE ABOVE WHEEL COMPARTMENT A compartment shall be provided above the rear wheels The compartment shall be 33 high x 62 wide x 26 usable depth The compartment shall have roll up door with a door opening 30 high x 54 wide The roll up door shall have a brushed satin finish DRIVER S SIDE COMPARTMENT BEHIND REAR WHEELS A compartment shall be provided behind the rear wheels The compartment shall be 64 high x 65
174. s far rearward as possible on the apparatus body Red with clear lenses ZONE C LOWER WARNING LIGHTING REAR Two Whelen model 60RO2FRR red LED s shall be mounted on the lower rear area of the appa ratus one each side red with clear lenses UPPER ZONE B D WARNING LIGHTING SIDE Two Whelen 600 Series 4 X 6 red L E D s shall be mounted on each side of the apparatus above the side compartments A chrome bezel shall be provided around the lights with clear lenses FEDERAL SIGNAL Q2B P MECHANICAL SIREN A Federal Signal model Q2B P pedestal mounted chrome plated mechanical siren shall be provided and mounted on the front bumper extension The siren shall have a maximum sound output of 123 db at 10 MECHANICAL SIREN ACTIVATION SWITCHES Two floor mounted pad switches shall be provided to operate the mechanical siren one on the right side and one on the left side MECHANICAL SIREN BRAKE A siren brake push button switch shall be provided on the dash or console 35 WHELEN 9E SCENELIGHTS Four Whelen 9E Series 9 x 7 26 degree scenelights shall be provided and mounted one on each side of the apparatus body and two on the rear The lights shall have a chrome plate trim bezel 12 VOLT SCENELIGHT ACTIVATION SWITCH 1 A single switch shall be located on the cab control console to activate the 12 volt scenelight s UNITY AG 6 DECK HOSEBED LIGHTS Two 2 Unity model AG 6 chrome plated lights shall be provided and mounte
175. s or seams COMPARTMENT FLOORS All compartment floors shall be constructed of fire apparatus quality stainless sheet steel The floors shall have a minimum 1 upward flange on the rear wall of the compartment to prevent any possible moisture accumulation in this area A drainport shall be provided in each rear corner of the compartment to allow any water that may collect on the floor to drain out The sides of the floor must be welded the full depth of the compartment to eliminate moisture accumulation These welds must be plac ed on the bottom exterior of the compartment so that they are not visible on the interior of the compartment The front edge of the compartment shall consist of a minimum of four bends to provide additional strength in the compartment floor and shall then form the lower door jamb All compartment floors shall be sweep out design This shall include the lower side compart ments any upper compartments and shall also include the rear face compartment Any exception to this requirement will cause immediate rejection of bid 20 COMPARTMENT REAR WALLS BODY SIDES The compartment rear walls and the apparatus body sides shall be constructed of fire apparatus quality stainless sheet steel The corners shall be one piece construction from top to bottom and from the inner body panel to the outer face of the compartment to provide maxi mum strength Corners using structural support channels or extrusions that require two or more piece
176. s to be welded together shall not be implemented SIDE REAR COMPARTMENT TOPS AND CEILINGS The side and rear compartment tops and ceilings shall be constructed of fire apparatus quality stainless sheet steel The ceiling of the lower side compartments in the extended depth section shall also be constructed of this material FENDERWELLS The left and right side rear fenderwells shall be constructed of fire apparatus quality stainless steel sheet steel A 1 gap shall be provided on the bottom of each side of the circular liner to allow drainage of water and for easy cleanout Sufficient clearance shall be provided for tire chains Before the booster tank is installed the fenderwells shall be throughly cleaned all seams sealed and automotive undercoated to prevent corrosion in the fenderwell area REMOVABLE INNER FENDER LINER The fenderwells shall be radius cut and shall have a circular inner liner to prevent rust pockets and for ease of cleaning The inner liner shall be constructed of high impact polyethene material and shall be fully removable for chassis suspension access STAINLESS STEEL FENDERETTE The fenderwells shall be trimmed with a polished stainless steel fenderette The stainless steel fenderette shall be secured into place with stainless steel fasteners and shall be easily removable for replacement A black rubber fender welting shall be provided between the fenderette and the inner liner surface The fenderettes shall protrude fr
177. shall be a TRW PS and shall be gear driven from the engine The pump shall be a balanced positive displacement sliding vane type ELECTRONIC POWER STEERING FLUID LEVEL INDICATOR The power steering fluid shall be monitored electronically and shall send a signal to activate an audible alarm and visual warning in the instrument panel when fluid level falls below normal FRONT AXLE CRAMP ANGLE The chassis shall have a front axle cramp angle of 48 degrees to the left and 44 degrees to the right POWER STEERING GEAR The power steering gear shall be a TRW model TAS 65 with an assist cylinder CHASSIS ALIGNMENT The chassis frame rails shall be measured to insure the length is correct and cross checked to make sure they run parallel and are square to each other The front and rear axles shall be laser aligned The front tires and wheels shall be aligned and toe in set on the front tires by the chassis manufacturer REAR AXLE The rear axle shall be a Meritor model RS 25 160 single drive axle The axle shall include precision forged single reduction differential gearing and shall have a fire service rated capacity of 27 000 pounds The axle shall be built of superior construction and quality components to provide the rugged dependability needed to stand up to the fire industry s demands The axle shall include rectangular shaped hot formed housing with a standard wall thickness of 0 63 of an inch for extra strength and rigidity
178. stem Fault indicates a failure in the brake system hydraulic brake systems only 5 Seat Belt Indicator indicates when a seat is occupied and corresponding seat belt remains unfastened YELLOW LAMPS Check Engine indicates engine fault 5 Check Trans indicates transmission fault 5 Wait to Start indicates active engine air preheat cycle 2 5 ABS indicates anti lock brake system fault 5 Water in Fuel indicates presence of water in fuel filter 7 5 Check Message Center indicates there is a fault message present in the LCD digital display SRS indicates a problem in the RollTek supplemental restraint system 1 5 DPF indicates a restriction of the diesel particulate filter 3 5 HEST indicates a high exhaust system temperature 3 5 MIL indicates an engine emission control system fault 3 5 Low Fuel indicates low fuel 4 GREEN LAMPS Left and Right turn signal indicators Aux Brake Active indicates secondary braking device is active 1 High Idle indicates engine high idle is active ATC indicates low wheel traction for automatic tractions control equipped vehicles also indicates mud snow mode is active for ATC system 5 OK to Pump indicates the pump engage conditions have been met 1 Pump Engaged indicates the pump is currently in use BLUE LAMPS High beam indicator The instrumentation system shall provide a constan
179. surance company Prices shall be quoted FOB Athens TN Delivery to City of Athens locations shall be without additional charge unless otherwise requested by the City of Athens Failure to examine any drawings specifications and instructions will be at bidder s risk If bidder is in doubt as to the true meaning of any part of the drawings specifications and instructions or other documents he should submit a written request for an interpretation to the Director of Finance An interpretation of the document will be made only by addendum issued by the Director of Finance to each firm to whom an invitation was forwarded The City will not be responsible for explanations or interpretations of bid documents except as issued in accordance herewith Where a brand or trade name appears in the specifications it is understood that the brand or trade name referred to or its approved equivalent shall be furnished If no mention is made of any exceptions it is assumed that he is bidding on the article mentioned and not an approved equivalent If a brand name is listed in the bid package and a vendor intends to bid another name it is the responsibility of the bidder to notify the Director of Finance of his intent to do so by seven 7 days prior to bid opening This is to allow time to evaluate equipment or product Failure to do so disqualifies you as a bidder An approved equivalent is defined as a bid item that meets or exceeds every specification pro
180. sure increase in RPM mode to a maximum of 30 psi Other safety features shall include recognition of no water conditions with an automatic programmed response and a push button to return the engine to idle The pressure governor monitoring and master pressure display shall be programmed to interface with a specific engine CLASS 1INTAKE RELIEF VALVE A Class 1 intake relief dump valve shall be provided in the intake side of the pump to relief excess incoming pressure The system shall be designed to self restore to a non relieving position when excessive pressure is no longer present The pressure adjustment range shall be from 50 psi to 200 psi The relief system shall be adjustable with a common type box end wrench The pressure setting shall be preset by the apparatus manufacturer at a 125 PSI position The surplus water shall discharge to the atmosphere at a location away from the pump operator s position PUMP SHIFT MECHANISM AIR ELECTRIC The pump shall be shifted from road to pump by means of a cab mounted air over electric pump shift switch The switch shall have a built in positive locking mechanism to prevent accidental movement of the switch The locking mechanism shall require operator to manually lift up on the switch lever to disengage the lock The switch shall have three positions Position 1 shall be road position position 2 shall be a neutral position and position 3 shall be pump position A green indicator light shall be prov
181. t a minimum engine speed position e The electronic controller is not presently attempting to execute an electronically controlled final drive gear shift e There is no active ABS event The compression brake shall be controlled through an off low high rocker switch on the dash FLUID FILLS The front of the chassis shall accommodate fluid fills for the engine oil and the power steering fluid through the grille This area shall also accommodate checks for the engine oil and power steering fluid ELECTRONIC ENGINE OIL LEVEL INDICATOR The engine oil shall be monitored electronically and shall send a signal to activate a warning in the instrument panel when levels fall below normal The warning shall activate in a low oil situation upon turning on the master battery and ignition switches without the engine running ENGINE WARRANTY The Cummins engine shall be warranted for a period of five 5 years or 100 000 miles whichever occurs first REMOTE THROTTLE HARNESS An apparatus interface wiring harness for the engine shall be supplied with the chassis The harness shall include a connector for connection to the chassis harness which shall terminate in the left frame rail behind the cab for reconnection by the apparatus builder The harness shall contain connectors for a Fire Research In Control 300 400 pressure governor and a multiplexed gauge Separate circuits shall be included for pump controls Pump Engaged and OK t
182. t audible alarm for the following situations Low air pressure Low engine oil pressure High engine coolant temperature High transmission oil temperature Low coolant level 1 High or low system voltage Critical engine fault Stop Engine The Check Message Center icon will illuminate and a message will be displayed in the LCD screen for the following situations Cab Ajar Low Oil Level Door Ajar Engine Communication Error Transmission Communication Error ABS Communication Error High Coolant Temp Turn Signal Reminder turn signal left on for more than one 1 mile Low Fuel Low Oil Pressure Low Coolant Level Low Battery Voltage High Battery Voltage Low Primary Air Pressure Low Secondary Air Pressure High Trans Temp The instrumentation system will provide a continuous alarm for the following situations Stop Engine Low Coolant Level 1 Brake System Fault Check Trans Check Engine ABS Engine Communications Error Transmission Communications Error ABS Communications Error Low Fuel Low Primary Air Pressure Low Secondary Air Pressure Low or High Battery Voltage High Trans Temp Low Oil Pressure High Coolant Temp The instrumentation system will provide a 160 millisecond second alarm every 880 milliseconds for the following situations Seat Belt Air Filter Water in Fuel Cab Ajar Low Oil Level Door Ajar The instrumentation system will provide a 160 millisecond second alarm every
183. the delivered apparatus which must be completed to achieve full compliance 4 An identification of the entity who will be responsible for making the necessary post delivery changes or modifications to the apparatus to achieved full compliance with the applicable standard Prior to or at the time of delivery of the apparatus the Statement of Exceptions shall be signed by an authorized agent of the entity responsible for the final assembly of the apparatus and by an authorized agent of the purchasing entity indicating a mutual understanding and agreement between the parties regarding the substance thereof The purchaser shall not place the apparatus into active emergency service until fully compliant with NFPA 1901 2009 NFPA REQUIRED EQUIPMENT The end user of this apparatus shall be providing all other equipment and accessories that is required by NFPA 1901 but not specifically listed in these specifications MAXIMUM TOP SPEED The maximum top speed of this apparatus shall be determined using the following NFPA 1901 Chapter 4 criteria Apparatus with 1250 gallon combined water tank capacity shall not exceed 60 MPH Apparatus with GVWR of over 50 000 Ibs shall not exceed 60 MPH Apparatus weighing over 26 000 Ibs shall not exceed 68 MPH WATEROUS MODEL CSU 1 500 GPM SINGLE STAGE PUMP The fire pump shall be a Waterous Fire Pump Company model CSU that complies with all applicable requirements of the latest edition of the Standard
184. their Department CAB DOOR TRIM REFLECTIVE The interior of each door shall include high visibility reflective tape A white reflective tape that measures 1 00 inch in width shall be provided vertically along the rear outer edge of the door The lowest portion of each door skin shall include a reflective tape chevron with red and white stripes and a Spartan logo The chevron tape shall measure 6 00 inches in height INTERIOR GRAB HANDLE A PILLAR There shall be two 2 rubber covered 11 00 inch grab handles installed inside the cab one on each A post at the left and right door openings The left handle shall be located 8 75 inches above the bottom of the door window opening and the right handle shall be located 1 00 inch above the bottom of the door window opening The handles shall assist personnel in entering and exiting the cab INTERIOR GRAB HANDLE FRONT DOOR Each front door shall include one 1 ergonomically contoured 9 00 inch cast aluminum handle mounted horizontally on the interior door panels The handles shall feature a textured black powder coat finish to assist personnel entering and exiting the cab INTERIOR GRAB HANDLE REAR DOOR A black powder coated cast aluminum assist handle shall be provided on the inside of each rear crew door A 30 00 inch long handle shall extend horizontally the width of the window just above the window sill The handle shall assist personnel in exiting and entering the cab INTERI
185. tios of all driving axles Maximum governed road speed Pump make model rated capacity in gallons per minute liters per minute where applicable and serial number Pump transmission make model serial number and gear ratio Auxiliary pump make model rated capacity in gallons per minute liters per minute where applicable and serial ATO Ta soa90 TD a eS 44 number Water tank certified capacity in gallons or liters if applicable Aeril device type rated in vertical height in feet rated horizontal height in feet and rated capacity in pounds Paint manufacturer and paint number s Company name and signature of responsible company representative cron Certification of slip resistance of all stepping standing and walking surfaces If the apparatus has a fire pump a copy of the pump manufacturers certification of suction capability If the apparatus has a pump a copy of the apparatus manufacturers approval for stationary pumping applications If the apparatus has a pump a copy of the engine manufacturers certified brake horsepower curve showing the maximum governed speed If the apparatus has a pump a copy of the pump manufacturers certification of the hydrostatic test If the apparatus has a pump a copy of the certification of inspection and test for the fire pump If the apparatus has an aerial device the certification of inspection and test for the aerial device If the apparatus has an aerial device all technical in
186. tor Fleetguard FS1003 w Lt amp Alarm Fuel Lines Nylon Fuel Shutoff Valve at Tank and at Primary Filter Fuel Tank 65 Gallon Fuel Tank Fill Port RH Mid LH Rwd Frt Axle Meritor MFS 20000 Beam Front Axle Warranty Meritor 2011 Frt Wheel Bearing Lube Oil Frt Shock Absorbers Bilstein Frt Suspension 9 Leaf 20000 21500 Steering Column Wheel Tilt Telescopic 18 Power Steering Pump TRW Elec Power Steering Fluid Level Indicator Front Axle Cramp Angle 48L 44R Degrees Power Steering Gear TRW TAS 65 w Assist Chassis Alignment Rear Axle 27000 Meritor RS 25 160 Rear Axle Differential Lubrication Oil Rear Axle Warranty Meritor 2011 Rear Wheel Bearing Lubrication Oil Vehicle Top Speed 65 MPH Rear Susp Reyco 79KB Spring 21000 31500 Conventional Frt Tire 385 65R 22 5 Michelin XZY3 Rear Tire 12R 22 5 Michelin XDN2 Rear Axle Ratio 5 38 Tire Pressure Ind Frt amp Rr Pop Up Voucher Frt Wheel Accuride 22 5 x 12 25 Alum Rr Whl Accuride 22 5 x 8 25 Alum Wheel Trim Hub amp Nut Covers SS Shiploose Brake System ABS ATC ESC Sgl Axle Frt Brakes S Cam Drum 16 5 x 6 Rr Brakes S Cam Drum 16 5 x 7 Cast Iron Shoe Prk Brake Rr Wheels Only Prk Brake Ctrl LH Dash Mnt Frt Brake Slack Adjusters Meritor Rr Brake Slack Adjusters Meritor Air Dryer Wabco System Saver 1200 Bhd RH Step Frt Brake Chambers MGM Type 30 Rr Brake Chambers TSE 30 36 Long Stroke Air Compressor Wabco SS318 18 7 CFM 3339 001 3303 006 3307 001 3308 002 3309 03
187. uency accurate to within 1 decimal point and Current Draw on two separate lines The display shall be capable of displaying total accumulated run time hours when the MODE button is pressed This information shall be stored in a non eraseable memory The frog display shall be located on the left side pump operators panel FRC OPTIMUM 1500 WATT TELESCOPING LIGHT Two 2 Fire Research model OPA530 M15 bottom raising telescoping light s shall be mounted on the apparatus The lighthead shall be a 1500 watt 220 volt AC and shall draw a maximum of 6 25 amps The pole shall be secured in any raised position with a non directional advanced twist lock locking device The twist lock mechanism shall have a knurled 39 positive grip The light s shall include a three wire coiled cord which is wired into the electrical distribution panel with an individual breaker for each light if more than one light The light s shall be electrically tested so that they are safe for their intended use The light s shall be certified by Underwriters Laboratories UL and shall meet exceed NFPA 1901 FIRE RESEARCH 1000 WATT TRI POD LIGHT One 1 Fire Research model OPA656 M10 ON GM tri pod telescoping light s shall be mounted on the apparatus The light shall have the following features On off switch underlighthead Wire guard to protect the lamp lens Model OP603 quick release mounting brackets 120 volt outlet located at mounting location
188. und when a door is open and the parking brake is released The light and alarm shall be interlocked for activation when a cab door is not firmly closed an apparatus cabinet door is not closed and the parking brake is released MASTER WARNING SWITCH A master switch shall be included in the main rocker switch panel The switch shall be a rocker type red in color and labeled Master for identification The switch shall feature control over all devices wired through it Any warning device switch left in the ON position shall automatically power up when the master switch is activated HEADLIGHT FLASHER An alternating high beam headlamp flashing system shall be installed into the high beam headlamp circuit which shall allow the high beams to flash alternately from left to right Deliberate operator selection of high beams will override the flashing function until low beams are again selected Per NFPA these clear flashing lights will also be disabled On Scene when the park brake is applied HEADLIGHT FLASHER SWITCH The flashing headlights shall be activated through a rocker switch on the switch panel The rocker switch shall be clearly labeled for identification INBOARD FRONT WARNING LIGHTS The cab front fascia shall include dual Whelen series 600 Super LED warning lights which shall offer multiple flash patterns including steady burn for solid colors and multiple flash patterns for split colors The lights sh
189. us Wiring Provision 8 Circuit Panel Load Management System Class Total System Manager Data Recording Sys Vehicle Data Pwr amp Gnd Stud 40A Batt Dir Aux Pwr amp Gnd Stud Bhd Sw Pnl 40A Mstr Sw 5032 002 5011 001 1701 034 1329 001 1731 002 1718 002 1719 003 1710 001 1713 002 1708 005 1715 001 1720 003 8002 001 1707 028 1721 001 1727 001 2704 002 2701 005 2708 001 2706 003 2705 002 2709 001 2801 001 2901 012 2902 010 1801 015 1806 001 1811 001 1815 002 1807 003 1814 002 1808 001 8005 001 3001 001 3005 002 3008 085 3009 007 ADDITIONAL POWER amp GROUND STUD EXTERIOR ELECTRICAL TERMINAL COATING ENGINE CAB ENGINE TUNNEL DIESEL PARTICULATE FILTER CONTROLS ENGINE PROGRAMMING HIGH IDLE SPEED ENGINE HIGH IDLE CONTROL ENGINE PROGRAMMING ROAD SPEED GOVERNOR AUXILIARY ENGINE BRAKE AUXILIARY ENGINE BRAKE CONTROL FLUID FILLS ELECTRONIC ENGINE OIL LEVEL INDICATOR ENGINE WARRANTY REMOTE THROTTLE HARNESS NGINE COOLING SYSTEM ENGINE COOLANT ELECTRONIC COOLANT LEVEL INDICATOR ENGINE PUMP HEAT EXCHANGER COOLANT HOSES ENGINE AIR INTAKE ENGINE EXHAUST SYSTEM ENGINE EXHAUST ACCESSORIES TRANSMISSION TRANSMISSION MODE PROGRAMMING TRANSMISSION FEATURE PROGRAMMING ELECTRONIC TRANSMISSION OIL LEVEL INDICATOR TRANSMISSION SHIFT SELECTOR TRANSMISSION PRE SELECT WITH AUXILIARY BRAKE TRANSMISSION COOLING SYSTEM TRANSMISSION WARRANTY DRIVELINE MIDSHIP PUMP
190. ve a lifetime non yellowing and freeze warranty The gauge shall also be warrantied for 4 years for defects in materials and workmanship including fluid leakage Warranty will not cover labor costs and or transportation costs PUMP PANEL AIR HORN BUTTON A momentary push button shall be provided on the pump panel to activate airhorns IDENTIFICATION LABELS FOR PUMP PANEL Innovative Controls verbiage label bezels shall be installed The bezel assemblies will be used to identify apparatus components These labels shall be designed and manufactured to withstand the specified apparatus service environment and shall be backed by a warranty equal to that of the exterior paint and finish The verbiage label bezel assemblies shall include a chrome plated panel mount bezel with durable easy to read UV resistant polycarbonate inserts featuring the specified verbiage and color coding These UV resistant polycarbonate verbiage and color inserts shall be sub surface screen printed to eliminate the possibility of wear and protect the inks from fading Both the insert labels and bezel shall be backed with 3M permanent adhesive 200MP which meets UL969 and NFPA standards AIR DISCHARGE CONNECTION A quick release air discharge female connector shall be installed on the pump panel The air discharge connector shall be compatible with either a Milton 787 Parker Hannifin B13 or Meyers 54 410 connector BOOSTER TANK UNITED PLASTIC FABRICATING INC 16 The
191. vided in the bid specifications and is approved by the City of Athens However the City of Athens reserves the right to choose a specific name brand if standardizing to Page 2 10 11 12 13 14 15 16 17 accommodate parts supply knowledge of maintenance and to prevent the purchase of specialty tools The bidder is requested to attach brochure type information and written specifications on the supplies furnished All guarantees and warranties should be clearly stated Prices quoted for all machinery equipment and vehicles shall include complete parts manual s maintenance manual s service manual s and operator s manual s without additional charge and are to be delivered with the unit Bids and modifications or corrections thereof received after the closing time specified will not be considered The City is not responsible for delays in delivery by mail courier etc Any exceptions to these terms or conditions or deviations from written specifications will be shown in writing and attached to the bid form Any alteration erasure additions to or omission of requested information change of the specifications or bidding schedule is made at the risk of the bidder and shall result in the rejection of the bid unless such changes are authorized by the specifications In the event cash discounts are offered by the bidder the discount date shall begin with the date of the invoice or the date of receipt of
192. y material one on the body and one in the door Each roll up door shall have an integral door open indicator magnet in the lift bar If the bar is not properly closed it shall activate the Door Open light in the cab The compartment lights shall function automatically when the door is opened A master compart ment light switch shall not be acceptable 33 DOOR AJAR INDICATOR L E D A1 X 2 RED LED flashing light shall be provided in the cab in clear view of the driver to warn of an open compartment or personnel door PERIMETER STEP LIGHTS There shall be seven Truck Lite model 40 underbody perimeter lights furnished and installed The lights shall be shock mounted and have an unbreakable polycarbonate lens and housing The light shall be sealed to help prevent moisture from entering the light The lights shall be located one under each side of the front of the body one under the chassis cab door 4 total and one under the rear step to illuminate the ground around the truck The ground lights shall be activated with the parking brake All runningboards walkways and steps shall be properly illuminated to NFPA standards WHELEN TRI CLUSTER TAILLIGHTS L E D INCANDESCENT Whelen 60ROOBRR 4 x 6 LED taillights and GOAOOTAR 4 x 6 LED turn signals shall be provided The backup lights shall be 4 x 6 clear incandescent A polished trim housing shall be provided one each side for mounting the tail lights turn signal lights

Download Pdf Manuals

Related Search

Related Contents

  PVG 32 Proportional Valves Service Manual    Olympus PT E03 User's Manual  Operating Instructions - müller co  Honeywell DN 10DY User's Manual  CHERRY MW 2300  BTG 20 LX - EOGB Energy Products  

Copyright © All rights reserved. Failed to retrieve file