1-800-345-4545 jegs.com
Contents
1. After pumping lower the lift arm to its full rest position 4 Install the oil fill plug Rotate the 62 handle in a clockwise direction until tight and pump the lift arm to maximum height without a load If the pumping condition has improved repeat steps 3 through 4 until all the air has been purged from the system Reinstall the cover plate OPERATING INSTRUCTIONS This is the safety alert symbol used for the OPERATING INSTRUCTIONS section of this manual to alert you to potential personal injury hazards Obey all instructions to avoid possible injury or death IMPORTANT Before attempting to raise any vehicle check vehicle service manual for recommended lifting surfaces OPERATION 1 To raise load Turn the handle in a clockwise direction until tight Position the jack under the load Proceed to pump the handle in order to raise the lift arm to the load As the saddle at the end of the lift arm gets closer to the load reposition the jack so the saddle will contact the load firmly and the load is centered on the saddle Make sure the saddle is correctly positioned Raise the load to the desired work height Place jack stands of appropriate capacity at the vehicle manufacturers s recommended support areas that provide stable support for the raised vehicle DO NOT CRAWL UNDER VEHICLE WHILE LIFTING VEHICLE OR PLACING OR REMOVING THE JACK STANDS Once jack stands are positioned turn the handle VERY SLOWLY Lower the load to rest on the jac2. an abnormal load or shock Any jack which appears to be damaged in any way is found to be badly worn or operates abnormally MUST BE REMOVED FROM SERVICE until necessary repairs are made by a manufacturer s authorized repair facility It is recommended that an annual inspection of the jack be made by a manufacturer s authorized repair facility and that any defective parts decals or warning labels be replaced with manufacturer s specified parts A list of authorized repair facilities is available from the manufacturer PROPER STORAGE It is recommended that the jack be stored in a dry location with all wheels touching the ground on a relatively level surface TROUBLESHOOTING Important Service jacks are self contained devices used for lifting but not Sustaining a partial vehicular load In accordance with ASME PALD Load Sustaining Test A load not less than the rated capacity shall not lower more than 1 8 3 18mm in the first minute nor a total of 1875 4 76mm in 10 minutes Lowering within this range is considered normal operation and is NOT a warrantable defect PROBIEM ACTION i Unitwiinotliitioad Purge air from hydraulic system by following procedure under SETUP 2 Unit will not sustain load or feels spongy under load Purge air from hydraulic system as above 3 Unit will not lift to full height Purge air from hydraulic system as above Pump the handle rapidly several times to push oil past ball valv
3. 6603ASJS50 power unit assembly 1 apo Jpumprolerade 4 2 pump roller 1 LE MEA 54 RSG603ASJ54 handle setscrew E ade o o 56 iiftarm right side plate a C me O 58 Jiftamade 1 5 pp fra Bo RS6603ASJ60 lowerhandle section 4 1 800 345 4545 jegs com Performance Products
4. Installation Instructions for 80077 3 Ton Aluminum Floor Jack Contents e Specifications Warning Information Setup and Operating Instructions Preventive Maintenance and Troubleshooting Hydraulic Maintenance Guide Exploded View Drawing and Replacement Parts Specifications Maximum Capacity aaneen 3 TON Minimum Height annen ennen 3 82 Maximum Height aaneen 19 3 Chassis Length ennen eenn 26 37 Overall Width nennen eenen 13 Handle Length annen ennen 47 6 Saddle Diameter unne ennen 4 52 1 800 345 4545 jegs com Performance Products SAMEN INFORMATION This is the safety alert symbol It is used to FE WARNING Indicates a alert you to potential personal injury AWAR N IN G hazardous situation which if hazards Obey all safety messages that not avoided could result in follow this symbol to avoid possible injury or death or serious injury death IMPORTANT READ THESE INSTRUCTIONS BEFORE OPERATING BEFORE USING THIS DEVICE READ THIS MANUAL COMPLETELY AND THOROUGHLY UNDERSTAND ITS OPERATING PROCEDURES SAFETY WARNINGS AND MAINTENANCE REQUIREMENTS It is the responsibility of the owner to make sure all personnel read this manual prior to using the device It is also the responsibility of the device owner to keep this manual intact and in a convenient location for all to see and read If the manual or product labels are lost or not legible contact Sunex for replacements If the operator is not fluent
5. es in power unit 5 Unit still does not operate Contact Sunex authorized hydraulic service center 4 Handle tends to rise up while the unit is under load OWNER USER RESPONSIBILITY The owner and or user must have an understanding of the manufacturer s operating instructions and warnings before using this jack Personnel involved in the use and operation of equipment shall be careful competent trained and qualified in the safe operation of the equipment and its proper use when servicing motor vehicles and their components Warning information should be emphasized and understood If the operator is not fluent in English the manufacturer s instructions and warning shall be read to and discussed with the operator in the operator s native language by the purchaser owner making sure that the operator comprehends its contents Owner and or user must study and maintain for future reference the manufacturers instructions Owner and or user is responsible for keeping all warning labels and instruction manuals legible and intact Replacement labels and literature are available from the manufacturer 1 800 345 4545 jegs com Performance Products HYDRAULIC MAINTENANCE GUIDE IMPORTANT Service jacks are designed for lifting purposes only always support raised load with jack stands REGULAR MAINTENANCE e MONTHLY or as necessary depending on usage 1 Using a grease gun add grease to grease fitting in the lift arm piv
6. es the jack should work normally right out of the box but it is not unusual for air to get trapped in the jack s hydraulic system during shipping and handling There are several symptoms of an air trapped hydraulic system which include only partial incremental pump stroke jack will not lift load jack will not sustain load or pumping feels spongy under load The following procedure will purge air from the hydraulic system and only needs to be done if experiencing the above mentioned conditions 1 The 36 saddle should be in its lowest position Remove the oil filler plug in the reservoir of the 50 hydraulic power unit 2 Look inside the oil fill plug hole You should be able to see the top of the power unit s cylinder The hydraulic fluid level should be no higher than the top of the cylinder Correct the fluid level if it is not at the proper height CAUTION In order to prevent seal damage and jack failure never use alcohol hydraulic brake fluid or transmission oil in the jack Use hydraulic jack oil a light turbine oil Chevron Hydraulic Oil AW ISO 32 or Unocal Unax AW 150 3 Close the release valve by turning the 62 handle clockwise until it stops Pump the jack against a load of at least 500 pounds 225 Kgs After the load is raised to maximum height slightly turn the 62 handle ina counterclockwise direction so the load is very slowly lowered while simultaneously and quickly pumping the handle 5 or 6 full incremental pump strokes
7. fting device only Immediately after lifting support the vehicle with jack stands capable of sustaining the load before working on the vehicle e Use only on a hard level surface free from obstructions so the jack is free to reposition itself during lifting and lowering operations e Center load on saddle Be sure setup is stable before working on vehicle e Do not move or dolly the vehicle while on the jack e Do not use saddle adapters or saddle extenders between the stock lifting saddle and the load e Do not use any adapters unless approved or supplied by JEGS e Always lower the jack slowly and carefully e This product contains one or more chemicals known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands thoroughly after handling Failure to heed these warnings may result in serious or fatal personal injury and or property damage CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS A WARNING Failure to read this manual completely and thoroughly failure to understand its OPERATING INSTRUCTIONS SAFETY WARNINGS MAINTENANCE INSTRUCTIONS and comply with them and failure to comply with the METHODS TO AVOID HAZARDOUS SITUATIONS could cause accidents resulting in serious or fatal personal injury and or property damage 1 800 345 4545 jegs com Performance Products PLEASE REFER TO THE EXPLODED VIEW DRAWING IN THIS MANUAL IN ORDER TO IDENTIFY PARTS IMPORTANT In most cas
8. in English the product and safety instructions shall be read to and discussed with the operator in the operator s native language by the purchaser owner or his designee making sure that the operator comprehends its contents THE NATURE OF HAZARDOUS SITUATIONS A WARNING The use of portable automotive lifting devices is subject to certain hazards that cannot be prevented by mechanical means but only by the exercise of intelligence care and common sense It is therefore essential to have owners and personnel involved in the use and operation of the equipment who are careful competent trained and qualified in the safe operation of the equipment and its proper use Examples of hazards are dropping tipping or slipping of loads caused primarily by improperly securing loads overloading off centered loads use on other than hard level surfaces and using equipment for a purpose for which it was not designed METHODS TO AVOID HAZARDOUS SITUATIONS AWARNING Read study understand and follow all instructions before operating this device Inspect the jack before each use Do not use jack if damaged altered modified in poor condition leaking hydraulic fluid or unstable due to loose or missing components Make corrections before using e Lift only on areas of the vehicle as specified by the vehicle manufacturer e Wear eye protection that meets ANSI Z87 1 and OSHA standards e Do not use jack beyond its rated capacity e This is a li
9. k stands Inspect the relationship between the jack stands and load to make sure the setup is stable and safe If the setup is not stable or safe follow the preceding steps until corrected 2 To lower load Follow the procedures mentioned in To raise load section of the OPERATING INSTRUCTIONS in order to raise the load off the jack stands Once the load has cleared the jack stands remove the jack stands from under the load and away from the work area Turn handle very slowly in a counterclockwise direction until the load is completely lowered to the ground Once the jack s lifting saddle has cleared the load remove the jack from under the load CAUTION Keep hands and feet away from the hinge mechanism of the jack PREVENTATIVE MAINTENANCE This is the safety alert symbol used for the PREVENTATIVE MAINTENANCE section of this manual to alert you to potential personal injury hazards Obey all instructions to avoid possible injury or death 1 Always store the jack in a well protected area where it will not be exposed to inclement weather corrosive vapors abrasive dust or any other harmful elements The jack must be cleared of water snow sand or grit before using 2 The jack must be lubricated periodically in order to prevent premature wearing of parts General purpose grease must be applied to all zerk grease fittings caster wheels front axle elevator arm handle base pivot bolts release mechanism and all other bearing surfaces Worn pa
10. ot shaft Use multi purpose NLGI type grease only Lubricate all linkages and pivot points Use white lithium spray grease only Remove handle lubricate handle receptacle and handle end Use white lithium spray grease only Lubricate both rear casters bearing and both front wheels Use white lithium spray grease only Tighten all accessible hardware Fy 1 800 345 4545 jegs com Performance Products REF NO PARTNO DESCRIPTION QTY a RS6603ASI01 rearcaster f2 2 po frearcaster bracket 2 a R56603A5J03 locking nutMi2 J4 4 taser S tooth washer tO 10 68 bamos OOOH gt othwashert2 J8 Boo bitmas gt ______ 38_ EOS MES PJ 0 ftootiwasherB 2 flokingmut 2 12 o fase A A A e AAA ng a ee a S o ee so radius linkage axle bot peaje Only reference numbers identified by part number are available individually an co Ge d hi a co cD EN Das Oa Pd PP Ro Pd Pd mo mo oy PD tf tj o AAL en eta AA A eae ata oe y atada de e e dl 4 a EE A ey es P F mn e ring 16 ro 34 sade base asp gasketofsaddie 4 38 RS6603ASJ36 sadde ____________ 4 37 o poo fsaddebot OST 38 RS6603ASJ38 saddlepad Sunex 4 C 40 saddebaseae 1 ECT TT A apo fiftarmmountingpiate 1 ap irkage ph 2 a o po inkage block 45 retamingrima22 2 48 pin gt C 2 48 po JbolMB5 2 49 iftarmretumsping 2 50 RS
11. rts resulting from inadequate or no lubrication are not eligible for warranty consideration See page 6 for lubrication instructions 3 It should not be necessary to refill or top off the reservoir with hydraulic fluid unless there is an external leak An external leak requires immediate repair which must be performed in a dirt free environment by an authorized service center 1 800 345 4545 jegs com Performance Products IMPORTANT In order to prevent seal damage and jack failure never use alcohol hydraulic brake fluid or transmission oil in the jack Use Chevron Hydraulic Oil AW ISO 32 or its equivalent Unocal Unax AW 150 4 Every jack owner is responsible for keeping the jack labels clean and readable Use a mild soap solution to wash external surfaces of the jack but not any moving hydraulic components 5 Inspect the jack before each use Do not use the jack if any component is cracked broken bent shows sign of damage or leaks hydraulic fluid Do not use the jack if it has loose or missing hardware or components or is modified in any way Take corrective action before using the jack again 6 Any hydraulic repairs within the warranty period must be performed by an authorized service center INSPECTION Visual inspection should be made before each use of the jack checking for leaking hydraulic fluid and damaged loose or missing parts Each jack must be inspected by a manufacturer s repair facility immediately if subjected to
Download Pdf Manuals
Related Search