311304J GTP10 Fuel Transfer Pump, Instructions-Parts
Contents
1. Ensure the tank is vented to allow air into the tank FIG 2 as the fuel is being pumped out Failure to provide a vent will cause priming problems 1 Apply PTFE thread tape provided with the pump to large thread of bung adapter 9 2 in X 1 in reducer fitting Install bung adapter to fuel tank 2 Assemble suction tube sections by applying 1 4 in to in wide bead of PVC cement PN 260086 white tube provided with the pump around the entire inside diameter of the coupler see FIG 1 While sliding the tube into the couplers turn the tube at least one full revolution until the tube bottoms out on FIG 3 the coupler see FIG 2 FIG 3 and FIG 4 This will allow the cement to coat the entire surface for the best possible seal Allow cement to set for 5 min utes minimum before installing pump into tank For tanks deeper than 36 in 914 mm you will need a standard 1 in 25 mm pipe with 1 in npt threads on one end Suction tubes longer than 60 in 1 52 m require a foot valve Graco Part No 260217 at the bottom of the tube to prevent loss of prime FIG 4 6 311304J Installation 3 Cut the suction tube so that it is 2 in 55 mm from Mou nting Hose and Nozzle the bottom of the tank when installed in the tank 1 Apply thread tape provided with pump to both ends 4 Insert gasket 7f into union nut 1k If using Graco of hose assembly Screw 34 NPT end of 90 union supplied PVC suction tube2. 24 VDC blue includes items 2a 2i KIT motor 115 VAC blue includes items 2a 2i KIT motor 230 VAC blue includes items 2a 2i KIT motor 12 VDC black includes items 2a 2i KIT motor 24 VDC black includes items 2a 2i KIT motor 115 VAC black includes items 2a 2i KIT motor 230 VAC black includes items 2a 2i COVER electrical HOUSING electrical 12 V BOLT hex 1 4 20 x 3 4 in NUT 10 32 WIRE NUT 260450 and 260451 WIRE NUT 260452 and 260453 FLAG TERMINAL MOTOR electric COVER nozzle GUIDE nozzle Qty NR NO m JA 3A pwnnoA Ref No 3 5 6 260456 3a 3b 3C 3d 7e 260457 4a 4c 7a 260300 5a 5b 5c 5d 260454 6a 6b 6c 260434 7a 4c 7b 1e 10c 7C 1f 10b 7d 1g 7e 3d 7f Description KIT filter universal includes items 3a 3d COVER strainer SCREEN SCREW hex head 10 24 x 3 8 in SEAL strainer cover KIT popoff includes items 4a 4c POPPET relief valve SPRING relief valve SEAL relief valve KIT suction pipe includes items 5a 5c PIPE PVC COUPLER PVC female ADAPTER PVC male CEMENT PVC not shown KIT cable 12 V and 24 V only includes items 6a 6c CLAMP battery BLACK SLEEVE RED SLEEVE STRAIN RELIEF ASSEMBLY power cable 18 ft 5 5 m fuse holder 20 amp fuse KIT packing includes items 7a 7f SEAL relief valve SEAL gear cover KEY drive
3. Troubleshooting Problem ae Soter Motor stalls when nozzle is closed _ Bypass relief valve 4a stuck Inspect relief valve making sure poppet is free Replace if damaged Low supply voltage Check supply voltage Gears 1c 10a damaged and Inspect gears Gears should turn binding freely Replace if damaged Faulty motor Replace motor Fuel leaking in motor mount Faulty or damaged motor shaft seal Replace shaft seal 19 7d Operating pump extended time with Do not exceed 5 minutes of operation nozzle closed with nozzle closed Motor shaft worn Replace motor if shaft has groove worn in seal area Motor overheating Gears 1c 10a binding Check to make sure gears turn freely on shaft Operating pump extended time with Do not exceed 5 minutes of operation nozzle closed with nozzle closed Clogged inlet strainer 3b Clean or replace see Maintenance page 9 Clogged suction tube hose or Inspect and clean if required nozzle Operating pump more than 30 min Limit operation to 30 minutes per utes continuous duty hour Switch will not turn pump on Blown fuse Replace fuse 20 amp automotive fuse Littelfuse ATO 257020 or Bussman ATC 20 Electrical problem Check that supply voltage is proper and getting to pa Check switch actuator cam 8c Cam should be actuating the switch 8e defective 311304J 11 Parts Drawing Parts Drawing Models 260000 through 260017 260019 260024 2
4. Warnings Warnings The following general warnings are for the setup use grounding maintenance and repair of this equipment Addi tional more specific warnings may be found throughout the body of this manual where applicable Symbols appear ing in the body of the manual refer to these general warnings When these symbols appear throughout the manual refer back to these pages for a description of the specific hazard IN FIRE AND EXPLOSION HAZARD When flammable fluids are present in the work area such as gasoline and windshield wiper fluid be aware that flammable fumes can ignite or explode To help prevent fire and explosion Use equipment only in well ventilated area Eliminate all ignition sources such as cigarettes and portable electric lamps Keep work area free of debris including rags and spilled or open containers of solvent and gasoline Do not plug or unplug power cords or turn lights on or off when flammable fumes are present Ground all equipment in the work area Use only grounded hoses If there is static sparking or you feel a shock stop operation immediately Do not use equipment until you identify and correct the problem Keep a fire extinguisher in the work area ELECTRIC SHOCK HAZARD Improper grounding setup or usage of the system can cause electric shock Turn off and disconnect power at main switch before disconnecting any cables and before servicing equipment Connect only to grounded power source All e
5. 60580 and 260581 12 VDC Models 260020 and 260021 24 VDC Models 260022 and 260023 230 VAC re Models 260025 through 260028 115 VAC ae meeen ae 260456 hey SEERE I o 7 r Packing Kit 260434 includes items 7a 7f 1b 260458 which are also included in other kits 1e 7b 10c es 260459 253723 1f 7c 10b gt 260457 r This end to hose 11 e a 260300 260450 oaf 260451 260452 z 260453 5a 253719 i 253720 253721 253722 e 83 eof gq BS 260433 f 253718 260454 ar gd be a a a M RR 12 311304J Parts List Parts List Models 260000 through 260017 260019 260024 260580 and 260581 12 VDC Models 260020 and 260021 24 VDC Models 260022 and 260023 230 VAC Models 260025 through 260028 115 VAC Ref No 260458 260459 253723 la 1b 1c 10a 1d le 7b 10c 1f 7c 10b 260450 260451 260452 260453 253719 253720 253721 253722 311304J Description KIT pump with swivel blue includes items 1a 1k KIT pump without swivel blue includes items 1a 1j KIT pump with swivel black includes items 1a 1k BODY assembly COVER gear GEAR SHAFT gear SEAL gear cover KEY drive SEAL shaft BOLT hex 5 16 18 x 3 4 in FITTING inlet NUT union 260458 and 253723 KIT motor 12 VDC blue includes items 2a 2i KIT motor
6. Instructions Parts List gt g GRACO GTP10 Pump For pumping gasoline diesel fuel and kerosene Do not use to pump other fluids including water Models 260000 through 260017 260019 260024 260580 and 260581 10 gpm 38 Ipm 12 VDC CSA C US listed motor Models 260020 and 260021 10 gpm 38 Ipm 24 VDC Models 260022 and 260023 12 gpm 45 Ipm 230 VAC Models 260025 through 260028 12 gpm 45 Ipm 115 VAC CSA C US listed motor 10 psi 0 07 MPa 0 7 bar Maximum Working Pressure 311304J EN Important Safety Instructions Read all warnings and instructions in this manual Save these instructions CSA mark applies only to 12 VDC DE and 115 VAC motors for Class I Div C US Group D Hazardous Locations PROVEN QUALITY LEADING TECHNOLOGY Models Models 12 VDC 10 gpm 38 Ipm 12 5 amps 260000 260069 12 ft 3 66 m grounded 260079 manual leaded diesel 260001 260069 12 ft 3 66 m grounded 260082 automatic regular diesel 260002 260069 12 ft 3 66 m grounded 260078 manual unleaded 260003 260069 12 ft 3 66 m grounded 260083 automatic unleaded 260526 4 ft 1 22 m UL listed assembly 260004 260523 8 ft 2 44 m UL listed assembly 260078 manual unleaded wi 260005 260525 5 ft 1 52 m UL listed assembly 260078 manual unleaded 260006 260078 manual unleaded 260007 260078 manual unleaded 260008 260524 6 ft 1 83 m UL listed assembly 260078 manu
7. SEAL shaft SEAL strainer cover GASKET inlet Qty lt NS m fA 13 Parts List continued Parts List continued Models 260000 through 260017 260019 and 260024 12 VDC Models 260020 and 260021 24 VDC Models 260022 and 260023 230 VAC Models 260025 through 260028 115 VAC Qty Ref No Description 8 260433 KIT switch blue includes items 8a 8g 253718 KIT switch black includes items 8a 8g 8a COVER switch 1 8b BRACKET switch 1 8c CAM actuator switch 1 8d SWITCH actuator assy 1 8e SWITCH 1 Sf SCREW phillips 8 32 x 3 8 in 2 8g SCREW phillips 6 32 x 1 4 in 1 9 260061 ADAPTER bung 1 10 260277 KIT gear includes 10a 10c 1 10a 1c GEAR 10b KEY drive 1 1f 7c 10c SEAL gear cover 1 1e 7b 11 see pg 2 ASSEMBLY hose 3 4 in not shown 12 seepg 2 ASSEMBLY nozzle not shown 138415G901 LABEL warning not shown 14 15F074 NIPPLE 3 4 in x 3 4 in 1 15 156589 ADAPTER 90 swivel 1 A Replacement Danger and Warning labels tags and cards are available at no cost Not used on models 260004 260006 260008 260009 260010 260013 260014 260015 260017 260019 260024 260580 and 260581 Used on 12 VDC and 24 VDC models only 14 311304J Technical Data Technical Data Power cable 18 ft 5 5 m 14 AWG 12 VDC and 24 VDC models only 12 VDC models 12 5 amps 24 VDC models 7 amps 115 VAC models 2 amps 230 VAC models 1 amps Duty cycle 30 m
8. al unleaded 260009 260525 5 ft 1 52 m UL listed assembly 260078 manual unleaded 260010 260522 10 ft 3 05 m UL listed assembly 260078 manual unleaded 260525 5 ft 1 52 m UL listed assembly 260528 8 ft 2 44 m UL listed assembly 260078 manual unleaded 260525 5 ft 1 52 m UL listed assembly 260078 manual unleaded 260014 260525 5 ft 1 52 m UL listed assembly 260078 manual unleaded 260523 8 ft 2 44 m UL listed assembly 260078 manual unleaded 270521 12 ft 3 66 m UL listed assembly 260525 5 ft 1 52 m UL listed assembly 260525 5 ft 1 52 m UL listed assembly None 260078 manual unleaded a x xo 260016 260078 manual unleaded 260017 260019 260024 None None 260580 260573 12 ft 3 66 m grounded 260079 manual leaded diesel 260581 260573 12 ft 3 66 m grounded 260082 automatic regular diesel 24 VDC 10 gpm 38 Ipm 7 amps 260020 260069 12 ft 3 66 m grounded 260079 manual leaded diesel 260069 12 ft 3 66 m grounded 260082 automatic regular diesel 230 VAC 12 gpm 45 Ipm 1 amps 260069 12 ft 3 66 m grounded 260078 manual unleaded 260069 12 ft 3 66 m grounded 260083 automatic unleaded 115 VAC 12 gpm 45 Ipm 2 amps 260078 manual unleaded None 260069 12 ft 3 66 m grounded 260026 260069 12 ft 3 66 m grounded 260027 260069 12 ft 3 66 m grounded 260028 260069 12 ft 3 66 m grounded 311304J Models 311304J 3
9. ble lift 311304J Operation Operation Before servicing turn pump off and open the nozzle to relieve pressure CAUTION Do not operate pump dry Do not run pump for more than 5 minutes with nozzle closed Do not operate pump for more than 30 minutes continuously in 1 hour On Off switch lever 8d is located under nozzle holder Remove nozzle before turning pump on 1 Move switch lever 8d on 2 Insert nozzle into tank and actuate nozzle lever to dispense fuel 3 Immediately after fueling turn switch lever 8d off Maintenance 1 Clean inlet strainer 8b after every 50 hours of operation 2 Toremove inlet strainer 3b remove four screws 3c and strainer cover 8a Remove and clean strainer 3 If strainer is excessively dirty clean tank to protect pump and the equipment being fueled 4 After cleaning strainer replace strainer and cover Make sure cover seal 3d 7e is in place Troubleshooting Troubleshooting Problem ae Soter Motor runs but pump will not prime Motor rotation wrong 12 Motor rotation wrong 12 VDC and and Check wiring instructions for possible wiring instructions for possible 24 VDC units only problems Missing relief valve o ring seal Remove gear cover 1b inspect seal 4c 7a 4c 7a replace if missing or damaged Sheared drive key 1f 7c Remove cover 1b and inspect key 1f 7c 10b replace if worn or sheared Dirt under relief poppet 4a o
10. c les proc dures concern es Graco Information For the latest information about Graco products visit www graco com For patent information see www graco com patents TO PLACE AN ORDER contact your Graco distributor or call to identify the nearest distributor Phone 612 623 6928 or Toll Free 1 800 533 9655 Fax 612 378 3590 All written and visual data contained in this document reflects the latest product information available at the time of publication Graco reserves the right to make changes at any time without notice This manual contains English MM 311304 Graco Headquarters Minneapolis International Offices Belgium China Japan Korea GRACO INC P O BOX 1441 MINNEAPOLIS MN 55440 1441 Copyright 2005 Graco Inc is registered to ISO 9001 www graco com Revised March 2015
11. cidental or consequential loss shall be available Any action for breach of warranty must be brought within two 2 years of the date of sale GRACO MAKES NO WARRANTY AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES EQUIPMENT MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO These items sold but not manufactured by Graco such as electric motors switches hose etc are subject to the warranty if any of their manufacturer Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties In no event will Graco be liable for indirect incidental special or consequential damages resulting from Graco supplying equipment hereunder or the furnishing performance or use of any products or other goods sold hereto whether due to a breach of contract breach of warranty the negligence of Graco or otherwise FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document as well as all documents notices and legal proceedings entered into given or instituted pursuant hereto or relating directly or indirectly hereto be drawn up in English Les parties reconnaissent avoir convenu que la r daction du pr sente document sera en Anglais ainsi que tous documents avis et procedures judiciaires ex cut s donn s ou intent s a la suite de ou en rapport directement ou indirectement ave
12. e 14 2 Pour fluid being pumped into pump outlet until com pletely filled 3 Re assemble Union Swivel 15 back onto nipple 14 Turn pump on The pump should gain prime in under 5 seconds 4 If pump still does not gain prime check for any major leaks in the system If no leaks are found then the pump is mechanically defective and should be reported to Graco Product Service for disposition It is important that the swivel end of the 90 union swivel 15 is assembled to the 3 outlet nipple 14 for proper sealing see fig 6 Also if the pump has difficulty priming it is easy to remove the swivel and pour fluid into the pump outlet cavity when assem bled this way If prime is lost 1 First make sure there are no fluid leaks from the pump outlet out to the fuel nozzle Any leaks after the outlet will allow air to push the fluid column back to the tank and prime will be lost 2 If no leaks are detected on the outlet side of the pump remove the pump from the tank and inspect the suction tube and pump inlet for leaks 3 If the system is leak free and the suction height guidelines are followed the pumping system should not lose prime All guidelines and procedures are based on pump ing diesel fuel If pumping gasoline priming may be more difficult due to the lift of gasoline dependent on Reid s vapor pressure of the gasoline and it s temperature The lower the vapor pressure and temperature the higher the possi
13. equate or improper maintenance negligence accident tampering or substitution of non Graco component parts Nor shall Graco be liable for malfunction damage or wear caused by the incompatibility of Graco equipment with structures accessories equipment or materials not supplied by Graco or the improper design manufacture installation operation or maintenance of structures accessories equipment or materials not supplied by Graco This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect If the claimed defect is verified Graco will repair or replace free of charge any defective parts The equipment will be returned to the original purchaser transportation prepaid If inspection of the equipment does not disclose any defect in material or workmanship repairs will be made at a reasonable charge which charges may include the costs of parts labor and transportation THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE Graco s sole obligation and buyer s sole remedy for any breach of warranty shall be as set forth above The buyer agrees that no other remedy including but not limited to incidental or consequential damages for lost profits lost sales injury to person or property or any other in
14. in hour uction tube 1 in x 34 in 25 4 mm x 864 mm carbon steel with zinc plating 416 and 302 stainless steel fluoroelastomer Buna N Aluminum Valox Nylon Nitrile PVC Vellumoid Valox is a registered trademark of the General Electric Company Performance Chart 14 95 0 095 12 81 0 081 10 68 0 068 8 54 0 054 6 41 0 041 4 27 0 027 2 0 14 0 014 0 gpm 0 2 4 6 8 10 12 14 lpm 7 6 15 1 22 7 30 3 37 9 45 4 53 0 OUTLET PRESSURE psi bar MPa S54 z msaa FLOW RATE PART NUMBERS LEGEND A 12VDC amp 24VDC Pressure B 1I5VAC amp 230VAC relief opens C 311304J 15 Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use With the exception of any special extended or limited warranty published by Graco Graco will for a period of twelve months from the date of sale repair or replace any part of the equipment determined by Graco to be defective This warranty applies only when the equipment is installed operated and maintained in accordance with Graco s written recommendations This warranty does not cover and Graco shall not be liable for general wear and tear or any malfunction damage or wear caused by faulty installation misapplication abrasion corrosion inad
15. ion from power cable 6c from end opposite of fuse 4 Strip 3 8 in 10 mm of insulation from red and black wires 5 Slide strain relief 6b over end of power cable 6c on the end just stripped Male thread of strain relief should be toward stripped end 6 Insert power cable through conduit thread in electri cal cover 2a Connect wires from power cable to wires from the motor using wire nuts 2e red to red and black to black 7 Screw strain relief 6b into electrical cover 2a 8 Position power cable 6c so the large diameter of power cable extends through strain relief 6b 9 Tighten nut on strain relief to form a seal around the power cable 10 Reinstall electrical cover 2a on the pump 11 Remove 1 2 in 13 mm of insulation from wires on the fuse holder end of the power cable 12 Attach battery clamps 6a with red sleeve to red wire and black sleeve to black wire Wire must be crimped to the battery clamp firmly to get a good electrical connection 13 Connect red wire with fuse holder inline to positive battery terminal Connect black wire to negative bat tery terminal Electrical Installation 115 VAC and 230 VAC On 115 VAC and 230 VAC pumps electrical con nections must be made by a licensed electrician per requirements of local state and national codes regarding class 1 group D installations Only rigid conduit with threaded connections or other approved wiring methods for Class 1
16. it is not necessary to swivel 15 to one end of hose see fig 5 apply thread tape before assembly just screw into pump inlet 1j If using metal suction tube not sup 2 Screw nozzle onto other end of hose and tighten plied with pump then apply thread tape provided with pump to NPT threads before assembling to 3 Start swivel end of 90 union swivel 15 onto 34 pump inlet 1j nipple 14 on pump outlet see FIG 5 Orient the hose nozzle assembly to desired position and 5 Insert suction tube attached to pump through bung tighten swivel fitting adapter 9 into tank Position pump as desired and tighten union nut 1k on bung adapter 9 It is important that the swivel end of the 90 union swivel 15 is assembled to the 3 outlet nipple 14 for proper sealing see FIG 6 If the pump has diffi culty priming it is easy to remove the swivel and pour fluid into the pump outlet cavity when assem bled this way FIG 5 FIG 6 311304J 7 Installation Electrical Installation 12 VDC and 24 VDC If you are installing models 260580 or 260581 skip this section These pumps have been factory wired To install wiring for a negative ground system 1 Ensure pump switch is OFF 2 To remove electrical cover 2a remove four bolts 2c Power cable can be cut to shorter length if 18 feet 5 5 m is not required Cut to proper length and proceed with steps 3 and 4 3 Strip 3 in 76 mm of outside insulat
17. lectrical wiring must be done by a qualified electrician and comply with all local codes and regulations PERSONAL PROTECTIVE EQUIPMENT You must wear appropriate protective equipment when operating servicing or when in the operating area of the equipment to help protect you from serious injury including eye injury inhalation of toxic fumes burns and hearing loss This equipment includes but is not limited to e Protective eyewear e Clothing and respirator as recommended by the fluid and solvent manufacturer e Gloves e Hearing protection PRESSURIZED EQUIPMENT HAZARD Fluid from the gun dispense valve leaks or ruptured components can splash in the eyes or on skin and Cause serious injury e Follow Pressure Relief Procedure in this manual when you stop dispensing and before cleaning checking or servicing equipment e Tighten all fluid connections before operating the equipment Check hoses tubes and couplings daily Replace worn or damaged parts immediately 4 311304J Warnings EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury e Do not operate the unit when fatigued or under the influence of drugs or alcohol e Do not exceed the maximum working pressure or temperature rating of the lowest rated system component See Technical Data in all equipment manuals Use fluids and solvents that are compatible with equipment wetted parts See Technical Data in all equipment manuals Read fluid and solvent manufactu
18. or Division 1 installations should be used Conduit opening in pump must be sealed with waterproof fuel resistant sealant Failure to comply with this warning could result in injury from electrical shock fire or explo sion 1 Ensure pump switch is OFF and electrical power is disconnected 2 Install conduit and user supplied power cord to pump 3 Strip 3 in 76 mm from power cord jacket and 1 2 in 13 mm from individual conductor insulation 4 Toremove electrical cover 2a remove four bolts 2c 5 Remove 1 2 in 13 mm of insulation from power wires inside pump electrical terminal cavity 6 Insert electrical power wire through conduit opening in back of pump 7 Using wire nuts 2e connect wires green to green white to white and black to black 8 Replace electrical cover 311304J Priming Pump All pump models should prime within 5 seconds after pump is turned on up to a height of 36 in 91 mm Pumps installed at height up to 5 ft 1 52 m may have difficulty priming Follow procedure below to initiate prime Pumps installed at suction height above 5 ft 1 52 m will have difficulty in holding prime It is recom mended that check valve Graco part no 260217 be added to the bottom of the suction tube to help maintain prime If prime in not achieved in 30 seconds after turning the pump on use the following procedure to initiate prime 1 Remove 90 Union Swivel 15 from 34 Inlet Nippl
19. r seal Remove cover 1b and inspect 4c 7a clean or replace if damaged Strainer seal 3d 7e leaking Inspect and replace if damaged Suction height too high to prime See Priming Pump page 9 Worn or damaged gears Remove cover 1b and inspect gears Replace if worn or damaged Fuel level low Refill tank Cover seal 1e7b 10c damaged Replace if worn or damaged Inlet strainer 3b clogged Remove and clean or replace Air leak in suction tube Inspect all joints in suction tube Make sure all joints in suction tube are sealed and that there are no cracks from over tightening Air lock in system This may occur if filter or meter or automatic shut off nozzle is used If this occurs fill pump and meter with fuel through top of pump Motor does not run at proper speed Check electric connections Check supply voltage for proper voltage level Unit pumps but output flow is low Clogged inlet strainer 3b Clean or replace Air leak in suction tube Check to make sure all joints in suc tion tube are sealed and that there are no cracks Suction tube too close to tank Suction tube must have a 2 in bottom 51 mm minimum clearance Tank empty Refill tank Tank not vented Tank must be vented to atmosphere Worn or damaged gears Remove cover 1b and inspect gears Replace if worn or damaged Damaged motor Replace motor Clogged suction tube hose or Inspect and clean nozzle 10 311304J
20. rer s warnings For complete information about your material request MSDS forms from distributor or retailer Check equipment daily Repair or replace worn or damaged parts immediately with genuine Graco replacement parts only Do not alter or modify equipment Use equipment only for its intended purpose Call your Graco distributor for information Route hoses and cables away from traffic areas sharp edges moving parts and hot surfaces Do not kink or over bend hoses or use hoses to pull equipment Keep children and animals away from work area Comply with all applicable safety regulations BURN HAZARD z Equipment surfaces and fluid that s heated can become very hot during operation To avoid severe burns do not touch hot fluid or equipment Wait until equipment fluid has cooled completely 311304J 5 Installation Installation A W A N ome Ko Le RM When unpacking pump check for shipping damage Report any shipping damage to delivering carrier imme diately CAUTION Do not use a curb pump automatic shut off nozzle with this pump Use of a curb pump automatic nozzle may cause priming problems reduced output flow FIG 1 and motor overheating If an automatic shut off nozzle is required use Graco part number 260082 regular or 260083 unleaded or Catlow Inc part number NCLF 1 regular or NCNLF 1 unleaded Mounting Pump Ensure tank being used is clean and free of welding slag
Download Pdf Manuals
Related Search