Home

Row Unit 2006 and on Service Manual 1 Planting DePth “V” Closing

Contents

1. Repeat STEP on all row units STEP2 Checkrow unit drive chain alignment and routing Repeat procedure on all row units D051705103 19 Tooth Bearing Driven Sprocket Sprocket PLTR24 NOTE Make sure connector link is installed C o Eoy Closed End with closed end oriented properly as shown Direction Of Chain Travel gt STEP 3 Install seed tube not supplied as part of row unit in shank as shown Position hook on the front of the seed tube METR29ddd over lower cross pin in shank Pivot top of seed tube forward and secure with retaining pin and locking clip Repeat on all row units Refer to the instructions supplied with the electronic seed monitor installaton instructions for additional information STEP 4 If additional optional equipment is being N ia a installed on the row unit see Optional y Attachment assembly section 06 Rev 8 07 DOWN PRESSURE OPTIONS Quick Adjustable Down Force Springs Package 1 Row 700 01132 1 8216X Mechanical Down Pressure Package 1 Row 4 D8249 Spring 2 D14217 Tab Lock Pin e x 1 1 2 2 B0186 Spring Anchor With the planter raised until the bottom of the toolbar is approximately 30 above the floor Install support stands to safely hold the planter until assembly is complete Install one down force spring to the L H parallel arms and one down force spring to the R H parallel arms a Install spring onto outside of lower parallel arm
2. 11 16 GBO0366 2 Extension Bracket A G6325X U Bolt Package For 5 x 7 Toolbar Includes 2 GD1113 4 G10230 4 G10104 Rev 9 11 JBA DES 31 a OO IL 7 2 15 Seed Opener Disc Blade Bearing Assembly Service Manual and Scrapers How Unit 2006 and on IP1272 Ange 32 4 E J Rev 9 11 How Unit 2006 and on ITEM RR ON 10 11 12 13 14 15 Rev 9 11 PART NO G10213 GD11259 GA2012R GA2012L G10325 G10622 G10328 G10622 GD11845 GD11017 G10204 G10427 GD10473 GA2014 GD11306 GB0301 G10912 GA8324 QTY Per Row PO N a N S I gt r NO N NDD 15 Seed Opener Disc Blade Bearing Assembly and Scrapers Service Manual DESCRIPTION See Shank Assembly Seed Tube and Depth Adjustment on page 24 Machine Bushing 9s 030 Thick As Required Sleeve 3 1 D x O D x 122 Long Disc Scraper R H Disc Scraper L H Shown Hex Head Cap Screw 16 x 224 Serrated Flange Nut 16 Hex Head Cap Screw 16 x 9s Serrated Flange Nut 16 Dust Cap Special Hex Head Cap Screw 11 x 1 L H Threads Special Machine Bushing x 1 O D Rivet 4 x 1 2 Bearing Housing Bearing Disc Blade 3 5 mm x 15 Seed Tube Guard Inner Scraper Hex Socket Head Cap Screw 9 e 18 x 1 Grade 8 Disc Blade Bearing Assembly Less Dust Cap Items 10 13 JANE a DEE Br o 33 How Unit 2006 and on Gauge Wheels Service Manu
3. Install U boltthrough holes in shank as shown at left Secure using 4 USS washers lock nuts and spacer Place plastic spacer between bander and shank side to center the bander DO NOT over tighten lock nuts Over tightening will crush the bander NOTE Hose should be shortened as required Attach direct drop bracket to wheel arm stop as shown below and at left Insert bottom of hose through shank cover wheel arm stop and into straight drop in furrow bracket as shown Na OSs e ey NOTE Replace 1 2 x 2 1 4 closing wheel attaching carriage a bolt with 1 2 x 2 12 carriage bolt to install straight drop CTS bracket DIRECTION OF TRAVEL STEP 8 Install reflective decals on hopper panel extensions following instructions supplied with that package 13 Rev 8 07 OPTIONAL ATTACHMENTS IS619 Row Unit Mounted No Till Coulter Row Unit Mounted No Till Coulter With 1 Bubbled Blade 700 01026 Style A 1 A5641 Coulter Arm Assembly 1 D7803 1 Fluted Blade 8 Flutes Row Unit Mounted No Till Coulter With 34 Fluted Blade 700 01062 Style A 1 A5641 Coulter Arm Assembly 1 D9254 34 Fluted Blade 13 Flutes Row Unit Mounted No Till Coulter With 1 Fluted Blade 700 01022 Style A 1 A5641 Coulter Arm Assembly 1 D7804 1 Bubbled Blade Row Unit Mounted No Till Coulter With 1 Bubbled Blade 700 01125 Style B 1 A11522 Coulter Arm Assembly 1 D7803 1 Fluted Blade 8 Flutes Row
4. Install dust cap supplied in Hardware Bag Torque cap screws to 110 ft lbs Torque jam nuts to 70 ft Ibs NOTE Opening in weed guard must point down 27 Rev 8 07 OPTIONAL ATTACHMENTS IS619 Residue Wheels For Use On Frame Mounted Coulter RESIDUE WHEELS OPERATION For Use With Frame Mounted Coulter The residue wheels for use with the frame mounted coulter may be used on pull row units only RU155a The residue wheels are attached to the frame mounted coulter with two cap screws and sleeves allowing the unit to free float A 2 position spindle bolt mounting allows the tined wheels to be mounted interlocked or staggered Depth adjustment is made using a spring loaded cam and pin with 11 positions in 1 4 increments A high point on the cam allows the wheels to be locked up so they do not contact the ground A weed guard located on the inboard side of each wheel aids in the prevention of weed wrap which can cause premature bearing failure 28 RU135kk NOTE Opening in weed guard must point down Rev 8 07 IS619 FINAL INSPECTION D D DU LU Lubricate per instructions See Operator amp Parts Manual Check for loose bolts nuts etc Check all drive chains for proper alignment Make sure all drive shafts rotate freely Make sure all row units are mounted correctly properly spaced and that they are squared on the toolbar Refer to planter assembly manual for additional information and
5. Predelivery Delivery Checklist DELIVERY CHECKLIST At the time the planter is delivered the following checklist is to be used as a reminder of very important information which should be conveyed to the customer Check off each item as it is fully explained to the customer E Advise the customer that the life expectancy of this or any other machine is dependent on regular lubrication as directed in the Operator amp Parts Manual Tell the customer about all applicable safety precautions Along with the customer check to be sure the reflective decals and SMV sign are clearly visible with the planter in transport position and attached to the tractor Check to be sure safety warning lights are in working condition Tell the customer to check federal state provincial and local regulations before towing or transporting on a road or highway Give the Operator amp Parts Manual to the customer and explain all operating adjustments Read warranty to customer Complete Warranty And Delivery Report form AFTER DELIVERY CHECKLIST The following is a list of items we suggest to check during the first season of use of the equipment m d d Check with the customer as to the performance of the planter Heview with the customer the importance of proper maintenance and adherence with all safety precautions Check for parts that may need to be adjusted or replaced Check to be sure all safety warning signs decals reflective
6. 19 310597 1 Square Head Set Screw 11 x 214 20 310503 1 Hex Jam Nut 11 Grade 2 Rev 9 11 DE 57 a OO IL 7 2 Row Unit Mounted Residue Wheel Service Manual Row Unit 2006 and on RU103dd RU103d spp 58 ANI 5 Rev 9 11 How Unit 2006 and on ITEM O A 05 nm N O 11 12 13 14 15 16 1 18 19 20 Rev 9 11 PART NO GD1132 GD10552 G10006 GD9724 G10133 G10109 GD9720 GA6838 G10033 G10228 G10102 GD5857 G10045 G10228 G10102 G10348 G10111 GD9715 GA6834 GA6832 G10574 G10111 GA6833 G10371 G10501 GA5654 GA2014 GD12534 GB0387 GA7446 GA12236 QTY Per Row Po gt Ny n5nn rn rnnnn 2n o co0 l2 l ll Row Unit Mounted Residue Wheel Service Manual DESCRIPTION Dust Cap Wheel 12 Tine 3s x 12 Hex Head Cap Screw 11 x 24 Backing Plate Hex Head Cap Screw 6 18 x 17 Lock Nut 6 18 Grade 8 Spacer 1 2 x 2 34e Long Wheel Mount Hex Head Cap Screw 13 x 31 2 Lock Washer 12 Hex Nut 13 Spring Hex Head Cap Screw 72 13 x 412 Lock Washer 12 Hex Nut 13 Hex Head Cap Screw 2 13 x 5 Lockup Bolt Lock Nut 2 13 Spacer 12 x 3 Long Lower Link Mount Carriage Bolt 2 13 x 1 Lock Nut 2 13 Upper Link Hex Head Cap Screw 2 13 x 3 Full Thread Hex Jam Nut 2 13 Grade 2 Hub W Bearings Bearing Cover Wheel 12 Tine x 12 Wheel Assemb
7. 20 x 3 4 Hex Nut 20 Push Connect 1 NPT Male x 1 4 Air Cylinder Filter Pan Head Machine Screw 4 20 x 34 x 34 Air Clutch Housing Air Clutch Assembly Items 1 17 JANE LS Fra Rev 9 11 This page left blank intentionally Parallel Arms Mounting Support Plate and service Manual Quick Adjustable Down Forces Springs Option ROW Unit 2006 and on IP1277 EN ge 30 4 E J Rev 9 11 Parallel Arms Mounting Support Plate and Row Unit 2006 and on Quick Adjustable Down Forces Springs Option service Manual ITEM PART NO QTY DESCRIPTION Per Row 1 GD1113 2 U Bolt 5 x 7 x 11 310230 4 Lock Washer 5 G10104 4 Hex Nut 11 2 GD10036 1 Mounting Support Plate 3 GB0218 8 Bushing 272 1 D x 7 O D x 1 2 Long 4 GD11422 2 Upper Parallel Arm 5 G11391 8 Flat Washer SAE 6 G10732 4 Hex Head Cap Screw 18 x 2 G10412 4 Lock Nut 18 7 GB0186 2 Spring Anchor 8 GD14217 2 Tab Lock Pin 74e x 1 9 GD8249 4 Standard Down Pressure Spring GD21337 Heavy Duty Down Pressure Spring 10 310752 2 Hex Head Cap Screw 18 x 214 310412 2 Lock Nut 18 11 GA5651 1 Lower Parallel Arm 12 G10751 2 Hex Head Cap Screw 18 x 134 310412 2 Lock Nut 18 13 GA1720 1 Bearing Sprocket 7 Hex Bore 14 310004 2 Hex Head Cap Screw 16 x 114 G11091 2 Serrated Flange Nut 16 15 G10007 4 Hex Head Cap Screw 11 x 11 2 G10230 4 Lock Washer G10104 4 Hex Nut
8. AA caa PS HH HS Row Unit 2006 and on DESCRIPTION External Retaining Ring Knob Spring Pin 4 x 112 See Granular Chemical Hopper and Hopper Panel Extension on page P31 Sprocket And Bearing Drive Clutch 24 Tooth Spring Shaft Coupler Spring Pin 24e x 1 Shaft Hex Socket Head Cap Screw No 10 24 x 7s Lock Washer No 10 Feed Roller Hex Bore Bearing Hex Bushing Chain No 41 108 Pitch Including Connector Link Connector Link No 41 Wave Washer 1 2 Flat Washer 4 SAE Slotted Hex Self Tapping Screw 14 20 x 3 4 Slotted Hex Self Tapping Screw No 10 x 38 Support Strap Metering Gate Granular Housing Granular Chemical Meter Complete Items 1 9 10 12 14 And 16 22 Granular Chemcial Meter Clutch Items 1 3 and 5 9 App Hra Rev 9 11 This page left blank intentionally How Unit 2006 and on Granular Chemical Banding Options Service Manual RUA061 RUA073 RU101mm RU83m Rev 9 11 App Mirada as 50 How Unit 2006 and on ITEM O A O N 10 11 12 13 14 15 16 17 18 Rev 9 11 PART NO GD2423 G11209 GD2947 G10523 GA6907 G10864 G10757 G10758 GD10963 G11385 G10110 GD10984 GD1115L G10452 GD1115R G10310 G10227 G10103 GD1116 GA2075 G10306 G10229 G10101 GD1118 G10315 GA6741 G1K385 G10003 G11387 QTY NN NNa amp NY Granular Chemical Banding Options Service Manual DESCRIPT
9. Lubrication and Maintenance How Unit 2006 and on ROW UNIT MOUNTED DISC FURROWER Lubricate bushings in support arm mounting bracket at frequency indicated in Lubrication of this section Check each bolt for proper torque If bolt is loose it should be removed and bushing inspected for cracks and wear Replace bushings as necessary NOTE Use only hardened flat washers Replace damaged flat washers with proper part Torque bolts to 130 ft Ib 176 2 N m Blade hubs are equipped with sealed bearings Replace bearings if a bearing sounds or feels rough when wheel is rotated Heplace solid or notched 12 diameter blades when worn to 11 ROW UNIT MOUNTED BED LEVELER Lubricate bushings in mounting bracket and links at frequency indicated in Lubrication of this section Check each bolt for proper torque If bolt is loose it should be removed and bushing inspected for cracks and wear Replace bushing if necessary NOTE Use only hardened flat washers Replace damaged flat washers with proper part Torque bolts to 130 ft Ib 176 2 N m ROW UNIT MOUNTED NO TILL COULTER Check nuts and hardware periodically for proper torque Be sure coulter is positioned square with row unit and aligned in front of row unit disc opener NOTE Torque 5s spindle hardware to 120 ft lb 162 N m Coulter blade can be adjusted to one of four settings Initially blade is set in highest position As blade wears it can be adjusted to one of three lo
10. turn Rock drill shaft slightly using a amp wrench to take pressure off of spring loaded pins in clutch to allow pins to pop out disengaging drive ENGAGE Rotate knurled collar turn and turn drill shaft with a 7 O0 wrench until drive pins engage drive sprocket Interplant clutch sprocket Rev 9 11 ge Fs 7 Service Manual Row Unit Operation How Unit 2006 and on INTERPLANT PUSH ROW UNIT LOCKUPS Push row unit lockups lock interplant row units in the raised position caution Improper lifting of row units can cause serious injury An empty row unit requires minimum 90 Ib 40 8 kg lift Set down pressure springs to minimum lower planter to ground and empty seed hopper before attempting to lift with this lever j Ne vos NA LEELA AAAS it TIUS MM Cv Nl NAN LEAN LU us F Lockup released for field operation INTERPLANT PUSH ROW UNIT VACUUM HOSE SHUTOFF Push row unit locked in raised position Storage mount Interplant vacuum hose shutoff located on side of shank When push row units are not used move row unit end of 2 vacuum hose on each push row unit to storage mount 8 x d H Rev 9 11 Row Unit Operation Row Unit 2006 and on Service Manual FRAME MOUNTED COULTER PULL ROW ONLY z BEND Spring adjustment bolt I Frame mounted coulters with 1 bubbled 1 fluted 8 flutes or 3 4 fluted 13 flutes blades are used on pull
11. 2 A8760 Weed Guard W Roll Pin 2 D1132 Dust Cap 2 10010 Cap Screw 11 x 3 2 2 10503 Hex Jam Nut 11 Grade 2 D05170708a Coulter Mounted Residue Wheels Attachment 700 01127 Style B 1 A11521 Wheel Mount Assembly 1 A12236 Wheel Assembly R H 1 A12235 Wheel Assembly L H 1 A7414 Hardware Bag 4 10213 Machine Bushing 030 Thick 2 A8760 Weed Guard W Roll Pin 2 D1132 Dust Cap 2 10010 Cap Screw 11 x 3 2 10503 Hex Jam Nut 11 Grade 2 The Coulter Mounted Residue Wheel Attachment is attached to the Row Unit Mounted No Till Coulter Attachment using one 1 2 x 9 1 Style A or 3 4 x 10 7 Style B cap screw sleeve or bushings and lock nut which allows the unit to free float Two holes in each residue wheel mounting bracket arm allow the tined wheels to be mounted interlocked or staggered Depth adjustment is made using a spring loaded cam and pin with 11 positions in 1 4 increments A high point on the cam allows the wheels to be locked up so they do not contact the ground Model 3700 planters with 20 or 22 row spacings require the use of row unit extension brackets 8 each of Order Code 700 01072 for 1 row at the wing lift wheel arms when the planter is equipped with Coulter Mounted Residue Wheels Model 3800 planters have row unit extension brackets on the 6 center row units as standard equipment If equipped with Coulter Mounted Residue Wheels and Notched Single Disc Fertilizer Openers row
12. AP 11 Row Unit Operation Service Manual Row Unit 2006 and on ROW UNIT MOUNTED NO TILL COULTER How unit mounted no till coulters with 1 bubbled 1 fluted 8 flutes or 3 4 fluted 13 flutes blades may be used on pull row units and push row units 34 fluted shown Four quick adjustable down force springs are required per row when using row unit mounted no till coulters See Quick Adjustable Down Force Springs Options Align coulter blade to row unit double disc openers Adjust by loosening four attaching bolts moving coulter arm and Blade adjustment holes tightening four attaching bolts Coulter blade can be adjusted to one of four 1 2 incremental settings in the forked arm Initial Row Unit Mounted No Till Coulter location is the top hole Move blade as it wears to one of the three lower hole to maintain coulter blade at or slightly below opener discs Adjust coulter below depth of double disc opener blades in very hard soil conditions such as compacted wheel tracks to improve opener penetration and cutting of surface residue Check operating depth by setting planter down on a level concrete floor and checking relationship between coulter blade and row unit opener blade Make sure planter is level and coulter is square with planter frame and aligned with row unit disc opener NOTE Torque 5s spindle hardware to 120 ft Ib 162 7 N m COULTER MOUNTED RESIDUE WHEELS Coulter mounted residue wheels are designed f
13. Cap Screw 16 x 31 2 Flat Washer SAE Lock Nut 16 Knob Spring Pin 4 x 112 External Retaining Ring Hex Head Cap Screw 18 x 24 Flat Washer SAE Lock Nut 18 Bushing 272 1 D x 7 O D x 1 2 Long Hopper Mount Clutch Adapter Plate Serrated Flange Nut 6 18 Carriage Bolt 6 18 x 1 Service Manual Double Sprocket And Bearing Drive Clutch 11 19 Tooth Mechanical Double Sprocket And Bearing Drive Clutch 11 28 Tooth EdgeVac Spring Shaft Coupler Spring Pin 24e x 1 Meter Drive Assembly 11 28 Tooth Items 3 And 8 11 EdgeVac Shown Meter Drive Assembly Complete 11 19 Tooth Items 3 And 8 11 AE a PS 43 Service Manual 44 App H Row Unit 2006 and on Rev 9 11 How Unit 2006 and on METR12 RU87e ITEM PART NO 1 GD11279 2 GA10634 3 GA9714 Rev 9 11 QTY Seed Hopper and Lid DESCRIPTION Lid Seed Hopper EdgeVac Seed Hopper Reinforced Mechanical A PE a PS Service Manual 45 Granular Chemical Hopper and Hopper Panel Service Manual Extension Row Unit 2006 and on METR14d EN ge 46 4 E J Rev 9 11 How Unit 2006 and on ITEM OON DOO BWNDY 11 12 13 14 15 16 17 18 19 20 21 22 Rev 9 11 PART NO G11387 GD2971 10 GD11219 G1020
14. Mount Shoulder Nut 34 16 Connector 3 x 1 NPT Elbow 9 x 18 NPT Extended used on outer push units Bracket Hanger Bearing 7s Hex Bore Hex Head Cap Screw 16 x 114 Flat Washer 3s SAE Spacer 1 4 Lock Nut 16 Link not applicable with row unit extension brackets Plate Hex Head Cap Screw 13 x 1 Flat Washer 12 SAE Lower Two Holes Only Lock Washer 12 Yoke Mount Yoke Mount Hex Head Cap Screw 2 13 x 17 Flat Washer 12 SAE Lock Washer 12 Hex Nut 2 13 Plate Extension Hex Head Cap Screw 12 13 x 1 Flat Washer 12 SAE Lock Nut 2 13 Lock Clamp See Air Clutch Pull Row Unit on page 28 Square Head Machine Bolt 6 18 x 134 Flange Nut 6 18 No Serration DE rra a Service Manual IP1265 ITEM O o 10 0 fBWN NS BEEN BEEN m Jo c1 c Inm gt 28 N PART NO GD18891 G11239 GR1831 G11295 G11243 GR1894 GR1829 GR1813 GR1818 GR1830 G10023 G10103 GR1819 GR1896 GR1898 G11296 GR1895 GA12405 ze s QTY Per Row 1 o o c o c c c o o C Air Clutch Pull Row Unit How Unit 2006 and on DESCRIPTION Spacer 1 4 O D x 1 Hex Head Cap Screw 10 32 x Sprocket 19 Tooth Retaining Ring Slotted Flat Head Machine Screw No 8 32 x 12 Stainless Steel Air Housing Cover Sprocket Hub Clutch Spring Ratchet Gear Hex Bushing Hex Head Cap Screw 14
15. Unit Mounted No Till Coulter With 34 Fluted Blade 700 01124 Style B 1 A11522 Coulter Arm Assembly 1 D9254 4 Fluted Blade 13 Flutes Row Unit Mounted No Till Coulter With 1 Fluted Blade 700 01126 Style B 1 A11522 Coulter Arm Assembly 1 D7804 1 Bubbled Blade Row unit mounted no till coulters with 1 bubbled 1 fluted or 34 fluted blades may be used on pull row units and or push row units One package is required per row DANGER Always install all safety lockup devices or lower machine to the ground before working under or around the machine LF212299 19a Style A Shown With 3 4 Fluted Blade 13 Flutes Two Sleeves For Installing Coulter Mounted Residue Wheels D05170706a Style B Shown With 3 4 Fluted Blade 13 Flutes One Sleeve For Installing Coulter Mounted Residue Wheels LF02159609 1 Fluted Blade 8 Flutes 34 Fluted Blade 13 Flutes 1 Bubbled Blade Rev 8 07 OPTIONAL ATTACHMENTS IS619 Row Unit Mounted No Till Coulter STEP 1 Install coulter blade onto hub RU102d Remove 95 x 4 cap screw and remove hub from forked arm Install coulter blade onto hub using carriage bolts and lock nuts Tighten hardware alternately to avoid distorting the blade LF212299 19a STEP 2 Install hub and coulter blade assembly using the top adjustment hole in the forked arm Install hub and coulter blade assembly into the top adjustment hole in the forked arm using Ys x 4 c
16. arms on each side of the row unit as shown below Pull row unit assist springs Push row unit assist springs EN ge 6 1 E J Rev 9 11 Row Unit Operation Row Unit 2006 and on Service Manual FIELD OPERATION NOTE Adjust down pressure with planter lowered and row openers in ground for most accurate adjustment Pressure can be adjusted from tractor using control console or at planter using manual control valves on compressor assembly I Pressure gauge Ss Shutoff valve e p ar oressure ms d as Control console Air compressor assembly controls ADJUST DOWN PRESSURE FROM CAB Push toggle switch left to increase or right to decrease pressure ADJUST DOWN PRESSURE AT PLANTER Push and hold decrease or increase button on compressor assembly to decrease or increase pressure NOTE Value on the air pressure gauge is NOT down pressure force Multiply air pressure psi by four 4 to calculate down pressure LOCK UP PUSH ROW UNITS EQUIPPED WITH PNEUMATIC DOWN PRESSURE SPRINGS 1 Press and hold button on solenoid until pressure gauge reads 5 PSI 2 Lock up units See Interplant Push Unit Lockup for instructions 3 Turn shutoff valve handle perpendicular to valve body to turn off push row unit air supply INTERPLANT PUSH ROW UNIT CLUTCH SPROCKET Push row unit clutch sprocket disengages interplant drive from push row unit drill shaft when only pull row units are used DISENGAGE Rotate knurled collar
17. decals and SMV sign are correctly located and legible Replace if damaged or missing Check to be sure safety warning lights are working properly 29 Hev 8 07 NOTES IS619 KINZE the KINZE logo Twin Line and Interplant are registered trademarks of KINZE Manufacturing Inc 30 Rev 8 07
18. secure using two No 3 hair pin clips 11 Rev 8 06 OPTIONAL ATTACHMENTS IS619 Granular Chemical Hopper With Meter Hopper Panel Extension And Bander STEP 7 Install granular chemical funnel The granular chemical funnel is designed to attach to the hopper support panel directly under the granular chemical meter using two No 10 x 1 2 self tapping screws The funnel can be installed facing forward or rearward depending on application The funnel is shown in the forward configuration for installation of 4 1 slope compensating banding or straight drop in furrow placement Slide the wire hose clamp onto the end of the hose Install hose over funnel outlet and slide wire hose clamp into place over funnel outlet and hose to secure hose in place RU10100 IMPORTANT The hose should be shortened as required to eliminate bends ensuring even distribution of chemical RU143d RU143e Install 4 7 slope compensating bander or straight drop in furrow bracket as shown on next page 12 Rev 1 07 OPTIONAL ATTACHMENTS IS619 Granular Chemical Hopper With Meter Hopper Panel Extension And Bander 4 SLOPE COMPENSATING BANDING RU101kk RU140 EN e Yo Spacer DIRECTION OF TRAVEL le STRAIGHT DROP IN FURROW PLACEMENT RU101pp Yo x 2 Ye Carriage Bolt Supplied In Hardware Bag Install bottom of hose through shank cover wheel arm stop and into slope compensating bander Install clamp at top of bander
19. supplied in the Hardware Bag Torque cap screws to 110 ft lbs Tighten jam nuts securely NOTE Opening in weed guard must point down RU153aa Ad aan n yr K ax 1 A D NN IN ay N m N AY iti RM PS M l in Han STEP 2 Install wheel arm assembly on coulter arm Raise the planter to transport position except 3140 and install all safety lockup devices Attach the mount assembly onto the no till coulter arm using the 3 4 x 10 1 2 cap screw 3 4 long bushings 4 SAE washers and 3 4 lock nut supplied with the mount assembly Torque hardware to 200 ft Ibs Welded Sleeve 18 Rev 8 07 OPTIONAL ATTACHMENTS IS619 Row Unit Mounted Disc Furrower Row Unit Mounted Disc Furrower With Notched Disc Blades 700 01029 Row Unit Mounted Disc Furrower With Solid Disc Blades 700 01037 7181X 7148X 1 A5718 Support Arm 1 A5718 Support Arm 1 A5896 Mounting Bracket Assembly 1 A5896 Mounting Bracket Assembly 1 10585 Cap Screw 2 13 x 3 1 4 1 10585 Cap Screw 2 13 x 3 4 1 10536 Pin 1 10536 Pin 4 10216 Washer 4 10216 Washer 5 10111 Lock Nut 13 5 10111 Lock Nut 13 4 10017 Cap Screw 2 13 x 1 1 2 4 10017 Cap Screw 2 13 x 1 1 2 1 10503 Jam Nut 11 1 10503 Jam Nut 11 4 D7889 Bushing 4 D7889 Bushing 2 D7890 Link 2 D7890 Link 1 10597 Set Screw 11 x 2 4 1 10597 Set Screw 11 x 2 1 4 1 A5715 Anchor 1 A5715 Anchor 1 A5719 Moun
20. the row unit The initial location of the coulter blade is in the top hole The blade can be relocated to one of the lower two holes 1 increments as wear occurs or if deeper operation of the blade is desired IS619 LF083002101 Spring Adjustment Bolt Spring Anchor Bar DOWN PRESSURE ADJUSTMENT Down force adjustment is made by tightening or loosening the two spring adjustment bolts With the planter in raised position turn the bolts clockwise to increase down pressure or counterclockwise to decrease down force Set both springs equally Down force on the blade is shown below in lbs All Threads Used Maximum End Of Spring Adjustment Bolt Flush With Spring Anchor End Of Spring Adjustment Bolt Extended 15 Through Spring Anchor Bar Bar Shown Above NOTE Avoid setting down pressure higher than is required for consistent soil penetration Excessive pressure will increase the chances of damage to coulter components when the coulter strikes an obstacle 25 Rev 8 07 OPTIONAL ATTACHMENTS IS619 Residue Wheels For Use On Frame Mounted Coulter Residue Wheels 700 01089 RU155a For Use With Frame Mounted Coulter 1 A9866 Wheel Mount Assembly 1 A12236 Wheel Assembly R H 1 A12235 Wheel Assembly L H 1 A9863 Hardware Bag 4 10213 Bushing 2 10010 Cap Screw 11 x 3 2 10503 Hex Jam Nut 11 Grade 2 1 10011 Cap Screw 11 x 5 1 2 1 10005 Cap Screw 11 x 1 4 2 D1132 Dust Ca
21. till coulters and or excessive blade to blade contact Seed tube guard inner scraper increases seed tube guard wear and requires more Gauge wheel seed opener disc blade removed frequent inspection and or replacement NOTICE Over tightening hex socket head cap screws may damage shank threads and require replacement of shank An excessively worn seed tube guard may allow blades to wear into row unit shank also requiring replacement of shank Remove seed tube and two hex socket head cap screws that attach seed tube guard Hold replacement seed tube guard centered between seed opener disc blades Install hex socket head cap screws DO NOT TIGHTEN Using a clamp or vise grip squeeze opener blades together in front of seed tube guard Tighten seed tube guard retaining screws Remove clamps Distance between seed tube guard and opener blades should be equal on both sides Reinstall seed tube FRAME MOUNTED COULTER NOTE Torque 5s spindle hardware to 120 ft lb 162 7 N m See Frame Mounted Coulter in Row Unit Operation section of this manual for depth and spring adjustment Replace 16 diameter coulter blade 1 fluted 1 bubbled or 3 4 fluted when worn to 14 maximum allowable wear RESIDUE WHEELS FOR USE WITH FRAME MOUNTED COULTER Wheel hub is equipped with sealed bearings Replace bearings if a bearing sounds or feels rough when wheel is rotated Frame mounted coulter residue wheels rr Taal 18 ANI J Rev 9 11
22. 1 GD1026 GD11962 G10108 G10670 GD1059L GD1059R G10002 G10229 G10312 G10620 G10325 G10567 GD11305 A10759 GD11424 G10023 G10621 GD1060 GA8371 GA4444 GD11239 G10602 Granular Chemical Hopper and Hopper Panel QTY Per Row ND DB 4 WH 000 RA HN HH HSH C Extension Service Manual DESCRIPTION Flat Washer SAE Sleeve 6 Long Spring Special Washer 9 x 1 O D Sleeve 1 3 6 Long Idler Lock Nut 16 Hair Pin Clip No 3 Support L H Shown Support R H Hex Head Cap Screw 16 x 3 4 Lock Washer 9 Carriage Bolt 6 18 x 3 4 Serrated Flange Nut 6 18 Hex Head Cap Screw 16 x 2 94 External Retaining Ring Plate Hopper Panel Extension Non Stock Item Sub Wholegoods Order Code 700 01099 Block Hex Head Cap Screw 1 20 x 3 4 Serrated Flange Nut 20 Hinge Hopper Lid Knob Spring Pin 1 4 x 112 JANE VILL GT Be 41 Service Manual RUA051 RUB028 RU91a ITEM OON OTF WN BEEN mm 0O A O MN 16 17 18 19 20 21 22 gt 48 PART NO G10567 GD11239 G10602 GA8364 GD11413 GD11240 GB0278 G10546 GD11297 G10921 G10257 GD7148 GB0115 GD7258 G3303 108 GRO196 G10660 G11385 G10570 G11073 GD1061 GD1063 GB0116 GA8326 GA8366 Granular Chemical Meter and Meter Drive QTY Per Row 3 1 1 N S PY NY
23. 17014 G10047 G11387 G10108 GA13593 Shank Assembly Seed Tube and Depth QTY Per Row NNa WO YO NN a NY NHN SS ht S I lt N NI lll ll 1 no C2 Adjustment Service Manual DESCRIPTION Implement Switch Bracket Hex Head Cap Screw 16 x 11 Lock Nut 16 Limit Switch W Cable Hex Slotted Head Cap Screw 3110 32 x 1 Serrated Flange Nut 10 32 Hex Head Cap Screw 16 x 324 Flat Washer SAE Chain No 41 98 Pitch Including Connector Link Mechanical Chain No 41 108 Pitch Including Connector Link EdgeVac Chain No 41 16 Pitch Including Connector Link Used W Row Unit Extension Brackets Connector Link No 41 Idler Sleeve 1 6 Long Special Washer x 17 O D Idler Spring Sleeve 1 Long Sun Shade Rubber Dust Cap Stop Hex Head Cap Screw 16 x 11 2 Lock Nut 16 Clevis Pin 1 4 x 21 Hair Pin Clip No 22 Carriage Bolt 6 18 x 3 4 Serrated Flange Nut 6 18 Shield See Gauge Wheels on page 34 See KPM III Electronic Seed Monitor on page lt gt See Planter Monitor Module PMM on page lt gt Hex Head Cap Screw 24 x 212 Grade 8 Lock Nut 24 Grade C Shank W Gauge Wheel Pivot Spindle And Set Screw Hex Head Cap Screw 2 13 x 34 Pivot Link Depth Adjustment Spindle Sleeve I D x 9e O D x 122 Long Collar Depth Adjustment Washer 7 O D x 13
24. 2 1 D x 134 If Applicable Pin 6 x 12 Lever Depth Adjustment Spring Handle Depth Adjustment Cap Plug Cover Depth Adjustment Hex Washer Head Cap Screw 16 x 1 Hose Guide Hex Head Cap Screw 16 x 194 Flat Washer 38 SAE Lock Nut 16 Implement Switch Assembly Items 1 2 Items not included in Implement Switch Assembly Rev 9 11 y 3 es How Unit 2006 and on Pneumatic Down Pressure Package Option Service Manual Pull Row Unit Shown RU157c RU159a RU157d A12405 NOTE Items that are not referenced on this page may be referenced on age 30 Push Row Unit Shown Rev 9 11 26 How Unit 2006 and on ITEM N 10 11 12 13 14 15 16 17 18 19 20 21 Rev 9 11 PART NO GA11982 G10037 G10228 GB0394 G11018 G11391 GD3180 30 GB0396 GB0397 GD19092 GD18011 GB0395 GA2180 G10004 G11387 GD11963 04 G10108 GD17794 GB0393 G10037 G11389 G10228 GB0390 GB0392 GB0391 G10017 G11389 G10228 G10102 GB0389 GB0398 G10039 G11389 G10111 GD11045 G10130 G10923 Pneumatic Down Pressure Package Option QTY Per Row 1 1 a NNN NO RAH HSH KH NNNYNMP AH KH A NDN HAH HAH NNNDYD Service Manual DESCRIPTION Air Spring Assembly Hex Head Cap Screw 2 13 x 11 Lock Washer 12 Saddle Hex Head Cap Screw 18 x 11 Flat Washer SAE Sleeve 7 O D x I D x 212 Head
25. Bearing Bearing Housing Rivet 1 4 x 12 Hex Head Cap Screw 11 x 24 Dust Cap Single Press Wheel Complete W Bearing Items 17 And 20 22 Covering Disc Blade Complete W Bearing Items 16 And 23 25 Ay p rra d V Closing Wheels Service Manual Row Unit 2006 and on IP1208 EN ge 38 4 E J Rev 9 11 How Unit 2006 and on ITEM 10 11 12 13 14 15 Rev 9 11 PART NO GD9120 G10064 GD1085 GA6171 GA6597 GA6171 GB0254 G10133 G10109 GA8322 GB0268 G10001 G11387 G11419 G10315 G11387 GB0282 GB0239 G10111 GD8460 G1K345 GD14065 G10599 G10308 G10101 G10013 G11391 GD1109 G10230 G10107 GA6434 QTY Per Row 4 12 1 1 N Nea amp NN PD N NN NNNDNRDR WAN V Closing Wheels Service Manual DESCRIPTION Nylon Half Wheel Hex Head Cap Screw 4 20 x 1 Rubber Tire 1 x 12 Bearing Cast Iron Closing Wheel W Bearing Bearing Lever Hex Head Cap Screw 6 18 x 17 Lock Nut 6 18 Grade 8 Arm Wheel Arm Mount Hex Head Cap Screw 16 x 1 Flat Washer SAE Carriage Bolt 13 x 274 Carriage Bolt 13 x 2 Used W Straight Drop In Furrow Granular Chemical Bracket Flat Washer SAE Stepped Bushing Eccentric Bushing Lock Nut 2 13 Spring Closing Wheel Shield Kit W Hardware and Instruction Closing Wheel Shield Carriage Bolt 16 x 114 Carriage Bolt 16 x 3 4 Hex Nut 16 Hex Head C
26. Clutch 22200 Replace worn items worn items Dirt debris buildup inside clutch Disassemble clean as needed Reassemble CLOSING WHEEL PROBLEM POSSIBLE CAUSE SOLUTION Closing wheel s leave severe Too much closing wheel down pressure Adjust closing wheel pressure imprint in soil Closing wheel s not firming soil Not enough closing wheel down pressure Adjust closing wheel pressure Severe no till around seed conditions may require use of cast iron closing wheels V closing wheel running on top of Improper centering Align See V Closing Wheel Adjustment seed furrow Single closing wheel not directly Improper centering Align See Covering Discs Single Press Wheel over seed Adjustment Em 22 AI Rev 9 11 This page left blank intentionally Shank Assembly Seed Tube and Depth Service Manual Adjustment Row Unit 2006 and on Ange 24 1 E 5 Rev 9 11 How Unit 2006 and on ITEM ONO Ol 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 A PART NO GD19317 G10003 G10108 GA13580 G11298 G11284 G10326 G11387 G3303 98 G3303 108 G3303 16 GRO196 GD11962 GD1026 G10201 GD1065 GD7318 GD16245 GD11845 GD10867 G10003 G10108 G10551 G10669 G10312 G10620 GD1033 G11008 G11007 GA10157 G10438 GB0265 GD11001 GD11259 GB0285 G10207 GD13361 GB0267 GD10993 GB0266 GD3612 GB0274 G11015 GD
27. D12829 1 Sleeve 15 G10046 1 Hex Head Cap Screw 11 x 5 G10107 1 Lock Nut 11 16 GA9845 1 Coulter Arm W Grease Fitting G10643 Grease Fitting 45 28 17 310011 1 Hex Head Cap Screw 11 x 51 2 G10107 1 Lock Nut 11 18 GB0218 3 Bushing 272 1 D x 7 O D x 1 2 Long 19 GD1132 2 Dust Cap 20 310010 2 Hex Head Cap Screw 11 x 3 310503 2 Hex Jam Nut 11 Grade 2 21 GD10552 2 Wheel 12 Tine 3s x 12 22 GA5654 2 Hub W Bearings GA2014 Bearing 29 GD9724 2 Backing Plate 24 310133 12 Hex Head Cap Screw 6 18 x 17 310109 12 Lock Nut 54e 18 Grade 8 25 G10213 2 Machine Bushing 9s 030 Thick 26 GA9862 2 Weed Guard W Spring Pin G10765 Spring Pin 4 x 1 27 GA9865 1 Mount 28 GA9861 1 Cam 29 GD10519 1 Spring 30 310974 1 Lock Nut W Nylon Insert 7 13 31 310005 1 Hex Head Cap Screw 11 x 194 G10107 4 Lock Nut 11 32 GA9864 1 Support 33 G10014 1 Hex Head Cap Screw 2 13 x 1 310102 1 Hex Nut 1 13 34 G10011 2 Hex Head Cap Screw 11 x 51 G11391 2 Flat Washer SAE G10730 2 Lock Nut W Nylon Insert 11 35 GD14170 2 Sleeve 3 36 GB0387 2 Wheel 12 Tine x 12 A GA7446 Wheel Assembly 12 Tine R H Items 21 24 Shown GA7445 Wheel Assembly 12 Tine L H Items 21 24 B GA12236 Wheel Assembly 12 Tine R H Items 22 23 24 and 36 Shown GA12235 Wheel Assembly 12 Tine L H Items 22 23 24 and 36 Rev 9 11 MENT EIET 63 VI oe Be This pag
28. EP 3 Remove support stands and lower planter to the ground See Row Unit Mounted Residue Wheel in the row unit operation section in the Operator amp Parts Manual for additional information 22 Rev 8 07 OPTIONAL ATTACHMENTS IS619 Frame Mounted Coulter Frame Mounted Coulter Frame Mounted Coulter With 1 Bubbled Blade 700 01088 With 1 Fluted Blade 700 01087 1 A9135 Frame Mounted Coulter 1 A9135 Frame Mounted Coulter 1 D7804 1 Bubbled Blade 1 D7803 1 Fluted Blade 8 Flutes Frame Mounted Coulter With 32 Fluted Blade 700 01086 1 A9135 Frame Mounted Coulter 1 D9254 34 Fluted Blade 13 Flutes The frame mounted coulter is designed to allow necessary spring down pressure on the coulter for maximum penetration while exerting less shock load on the row unit DANGER Always install all safety lockup devices or lower machine to the ground before working 1 Bubbled Blade 34 Fluted Blade 13 Flutes under or around the machine 1 Fluted Blade 8 Flutes LF083002101 D03210204b LF02159609 Coulter Frame Attaching Plate W Angle Coulter Arm D03210207b end s E STEP 1 Raise the planter until the bottom of the toolbar is approximately 23 above the floor Hemove seed hoppers from row units to allow easier access for installation of coulters Heinstall hoppers after installation STEP 2 Install blade Remove the hub assembly from the coulter assembly and install blade 23 Re
29. ION Funnel Wire Hose Clamp 3 4 Hose Ae x 28 Slotted Pan Head Self Tapping Screw No 10 x 1 Slope Compensating Bander W Hardware 472 Band Width Uni Clamp Pan Head Screw No 10 32 x 1 Hex Nut No 10 32 U Bolt 1 x 1 6 x 1 4 20 Flat Washer 4 SAE Lock Nut 20 Grade B Spacer Hanger Bracket L H Cotter Pin s x 1 2 Hanger Bracket R H Carriage Bolt 20 x 3 4 Grade 2 Lock Washer 1 4 Hex Nut 20 Hanger Diffuser 14 Band Carriage Bolt 16 x 2 Lock Washer 3 4 Hex Nut 16 Clamp Carriage Bolt 2 13 x 2 Replaces Existing 1 2 x 2 Hardware Bracket Straight Drop In Furrow Bander Shield Kit W Hardware And Instruction Hex Head Cap Screw 16 x 11 2 Flat Washer 38 SAE y 3 9 Spring Tooth Incorporator Service Manual Row Unit 2006 and on RUA055 RU95 ITEM PART NO QTY DESCRIPTION Per Row 1 G10621 4 Serrated Flange Nut 20 2 GD2460 2 Eyebolt 20 3 G3305 01 2 Twin Loop Chain 9 Links 4 GD1143 1 Front Bracket 5 G10305 4 Carriage Bolt 16 x 1 310529 4 External Tooth Lock Washer 35 310622 4 Serrated Flange Nut 16 6 GD1145 7 Spring Tooth 7 G10305 9 Carriage Bolt 16 x 1 310622 9 Serrated Flange Nut 16 8 GD1144 1 Rear Bracket 9 GA2094 2 Cable Assembly 52 DE Rev 9 11 a ST er r How Unit 2006 and on D14398 RU102c RU152 Row Unit Mounted No Till Coulter Service Manual ITEM Re
30. Row Unit Operation Row Unit 2006 and on Service Manual PLANTING DEPTH Planting Planting depth is maintained by adjustable row unit gauge depth wheels Depth adjustment range is approximately 1 to 3 adjustment handle 1 Raise planter to remove weight from wheels y 2 Push down on depth adjustment handle and reposition it forward to decrease or rearward to increase planting depth Initially adjust all units to the same setting 3 Lower planter and check operation and planting depth of all row units Readjust individual rows as needed for uniform operation V CLOSING WHEEL ADJUSTMENT RUBBER OR CAST IRON Planting depth adjustment Eccentric bushing Down pressure adjustment lever Set closing wheels in forward hole for directly opposite installation Eccentric ZA bushing LA C V Closing wheel adjustments V closing wheels should have enough down pressure to close the seed trench and ensure good soil to seed contact Move 5 position quick adjustable down force lever on the top of closing wheel arm to the rear to increase closing wheel spring pressure Move lever forward to decrease pressure Adjust all row units to a similar setting Light soil usually requires less down force at average depth approximately 2 while heavy soil requires increased down force Eccentric bushings in the wheel arm stop allow for lateral adjustment of the V closing wheel assembly Use a 3 4 wrench to loosen hardw
31. Shown With Cast Iron Closing Wheels Installed A10949 Hardware Bag 8 Rows 12 10013 Hex Head Cap Screw 11 x 3 16 10013 Hex Head Cap Screw 11 x 3 12 10230 Lock Washer 9 16 10230 Lock Washer 12 D7805 Special Washer 3s Hardened 16 D7805 Special Washer Hardened 12 D1109 Bushing 44 I D x O D x Ys Long 16 D1109 Bushing amp 4 I D x 7 amp O D x 1 4 Long 12 10107 Lock Nut 11 16 10107 Lock Nut 11 NOTE Hardware for installing closing wheels is shipped in the bulk seed hopper STEP 1 STEP 2 PULL ROW UNIT CLOSING WHEEL INSTALLATION Install closing wheel on each side of arm using installation holes at the rear of the arm as shown Assemble x 3 Ya cap screw through lock washer through closing wheel through 1 4 bushing through hardened washer and through arm Secure with 9s lock nut on inside of arm Position eccentric bushings to align closing wheels to seed trench Tighten closing wheel attaching hardware NOTE Install cast iron closing wheel with beveled edge to inside as shown in photo above D08240701 Initial setting adjust the eccentric bushing on both sides with the long portion of the eccentric straight back as shown Rev 8 07 OPTIONAL ATTACHMENTS IS619 Granular Chemical Hopper With Meter Hopper Panel Extension And Bander Granular Chemical Hopper With Meter Hopper Panel Extension And Bander 700 01077 1 7532X Chemical Hopper W Meter An
32. TR14aa 1 6 Long Sleeve uu Special Washer Lao ON Spring e at amp op y We Long Sleeve ai 38 USS Washers 3 16 x 2 Cap Screw METR14bb 24 Tooth Sprocket And Bearing Drive Clutch Meter Drive e 18 x 34 Carriage Bolt And Flange Nut TR Plate 10 Rev 8 07 OPTIONAL ATTACHMENTS IS619 Granular Chemical Hopper With Meter Hopper Panel Extension And Bander STEP 4 STEP 5 STEP 6 Install granular chemical hopper as shown below Engage drive by rotating knob clockwise To disengage drive turn knob counterclockwise Align clutch drive coupler with meter shaft Tighten hardware METR39a No 3 Hair Pin Clip Granular Chemical Hopper With Meter Install drive chains Remove hopper Install granular chemical drive chain through idler and around 11 tooth sprocket of double sprocket in row unit drive clutch Route chain through slot in hopper support and around granular chemical clutch sprocket Use connecting link provided to couple chain D051705102 RHO004 RU57b Granular 11 Tooth Chemical Sprocket Driven On Seed Sprocket Drive PLTR24 NOTE Make sure connector link is installed O PAN Closed End with closed end properly oriented as shown DIRECTION OF CHAIN TRAVEL p Reposition granular chemical hopper on hopper support panel and
33. Wheels lt sincnssianencsbsanien sip intsung sins endures aaeadasninundasianaucveiwsaanaseiunaaianioaeansuanian 8 OPTIONAL ATTACHMENTS Coulter Mounted Residue Wheels 00 00 0c ccccssccceesscceceeesseceeeeseeecerseeeeeessssessecaeesecerteeseserneeeens 17 Frame Mounted Coulter PNE m 23 Granular Chemical Hopper With Meter Hopper Panel Per 9 Residue Wheels For Frame Mounted Cowulter esee 26 Row Unit Mounted Disc FUTONE Lauaske ane A CUN psa Tesada Ua eA SURE CUN VES 19 How Unit Mounted No Till Coulter arrrnanrrnnnnnnannnnnnnennnnnnnnnennnnnnnnnennnnennansnnnnrnnnnennnnnnnnnnen 14 Row Unit Mounted Residue Wheel iiiisssssssseesisssseseese eene eene nnne nian nnns 22 FINAL INSPECTION DELIVERY CHECKLIST AFTER DELIVERY CHECKLIST 29 05 Rev 8 07 PULL ROW UNIT IS619 Less Closing Wheels And Down Pressure Options NOTE See Closing Wheel Options section of these instructions for information on the assembly of rubber V closing wheels or cast iron V closing wheels NOTE Row units and U bolts are installed on the base machine Down pressure options seed meters seed discs or seed tubes are not supplied with base machine STEP 1 Install seed metering unit with shank cover on mini hopper Assemble selected seed disc on meter if installing brush type seed meters D041801103 RU13I RU149 DO NOT OVER TIGHTEN 716 X74 Locking Thumbscrews
34. al Rev 9 11 App Mirada as 34 How Unit 2006 and on ITEM JI CO N OA 10 11 12 13 14 15 16 Rev 9 11 PART NO GA7975 GA7976 GB0276 G10014 G10228 G10216 GD11423 GD1086 GD11453 G10924 G10620 G10338 G10620 G10010 G10018 G10109 GA6171 GD10991 G10204 G10640 G10940 GA7949 G1K296 QTY Per Row coco rmm A NN N Gauge Wheels Service Manual DESCRIPTION See Shank Assembly Seed Tube and Depth Adjustment on page 24 Wheel Arm W Grease Fitting Bushings And Seals L H Shown Includes Items 3 and 13 Wheel Arm W Grease Fitting Bushings And Seals R H Includes Items 3 and 13 Bushing 1 I D x 1 O D x 1 Long Per Arm Hex Head Cap Screw 2 13 x 1 Lock Washer 12 Washer v2 USS Half Wheel Tire Cover Carriage Bolt 6 18 x 194 Serrated Flange Nut 6 18 Carriage Bolt 6 18 x 1 Serrated Flange Nut 6 18 Hex Head Cap Screw 11 x 3 Hex Head Cap Screw 6 18 x 9e Lock Nut 6 18 Grade 8 Bearing Seal Per Arm Special Machine Bushing x 1 O D Grease Fitting 1 4 28 Per Arm Machine Bushing 1 048 Thick Gauge Wheel Complete Items 5 9 And 11 12 Gauge Wheel Arm Bushing And Seal Driver Kit Includes 1 Seal Driver 1 Bushing Driver 1 Instruction y 3 ES Covering Discs Single Press Wheel Service Manual How Unit 2006 and on RUAO54 RUBO26 RU944
35. ap Screw 11 x 31 2 Flat Washer SAE Bushing 44 I D x O D x 4 Long Lock Washer 5 Lock Nut 11 Rubber Closing Wheel Complete W Bearing Items 1 3 y 3 Service Manual IP1202 ITEM d o1 Ac 40 PART NO GD11509 G10007 G10230 G10104 GA8322 GD11313 GD11508 G10599 G10229 G11387 G10101 G7566X 9 o9 QTY Per Row 1 000 N a ma Drag Closing Attachment Row Unit 2006 and on DESCRIPTION Rear Bracket Hex Head Cap Screw 11 x 11 2 Lock Washer Hex Nut 11 Arm Blade Front Bracket Carriage Bolt 16 x 114 Lock Washer 9 Flat Washer SAE Hex Nut 16 Drag Closing Attachment Complete Items 1 6 JANE Pa Rev 9 11 This page left blank intentionally Hopper Support and Meter Drive Service Manual Row Unit 2006 and on IP1209 Ange 42 1 E 5 Rev 9 11 How Unit 2006 and on ITEM PART NO 1 GA2007 G10621 G10309 2 GA10155 G10061 G11387 G10108 3 GD11239 G10602 G10567 4 310752 311391 310412 5 GB0218 6 GB0314 7 GB0331 G10620 G10338 8 GA10137 GA12143 9 GD11413 10 GD15747 11 GB0278 G10546 A GA12144 B GA10151 Rev 9 11 QTY Per Row DDD PO PO PO PO YP NJ NY NN e Hopper Support and Meter Drive DESCRIPTION Hopper Hold Down Latch Serrated Flange Nut 20 Carriage Bolt 20 x Grade 2 Hopper Support Hex Head
36. ap screw and lock nut If bearing adapters have been removedfrom hub reinstall into hub before installing hub into forked arm Torque spindle bolt to 120 ft Ibs Comer st Depth Adjustment Holes D09070620 STEP 3 Attach coulterarm assembly to row unit face plate Raise the planter until the bottom of the toolbar is approximately 30 above the floor Install support stands to safely support the planter until assembly is complete Attach coulter arm assembly to row unit face plate using carriage bolts and lock nuts as shown 2 x 1 4 Carriage Bolts Do not tighten completely at this time And Lock Nuts Shown Installed On Push Row Unit STEP 4 Align coulter arm assembly Shift coulter arm assembly within the limits of the adjustment slots See photo in STEP 3 until coulter is aligned with row unit double disc openers Torque 1 2 bolts to 57 ft Ibs 15 Rev 8 07 OPTIONAL ATTACHMENTS IS619 Row Unit Mounted No Till Coulter Important Be sure down pressure options have been installed correctly as instructed in that section STEP 5 Remove support stands and lower planter to the ground 16 Rev 8 07 OPTIONAL ATTACHMENTS IS619 Coulter Mounted Residue Wheels LF212299 23 Coulter Mounted Residue Wheels Attachment 700 01069 Style A 1 A7413 Wheel Mount Assembly 1 A7446 Wheel Assembly R H 1 A7445 Wheel Assembly L H 1 A7414 Hardware Bag 4 10213 Machine Bushing 030 Thick 4
37. are attaching closing wheel arm to wheel arm stop Use another 34 wrench to turn eccentric bushings until closing wheels are aligned with seed trench Tighten hardware Closing wheels can be installed offset to improve residue flow or directly opposite Use forward installation holes If set directly opposite CLOSING WHEEL SHIELD RUBBER OR CAST IRON V CLOSING WHEELS Optional closing wheel shield is installed on underside of closing wheel arm to help prevent root balls and stalks from clogging closing wheels Closing wheel shield Closing wheel removed BS gem Rev 9 11 f AP 3 1 Row Unit Operation Service Manual Row Unit 2006 and on DRAG CLOSING ATTACHMENT Drag closing attachment pulls loose soil over seed trench NOTE Use of a seed firming wheel or other seed firming Eccentric device is recommended with drag closing attachment bushing Front and rear adjustment is made using slotted holes in blades Adjust all rows the same Wheel arm stop eccentric bushings provide lateral adjustment Use a 3 4 wrench to loosen closing wheel arm to wheel arm stop hardware Use another 3 4 wrench to turn eccentric bushings until drag closing attachment is aligned with seed trench Tighten hardware Drag closing attachment COVERING DISCS SINGLE PRESS WHEEL ADJUSTMENT Adjusting bolt Ld Lad Zo E y lp E v Press wheel down force adjustment Check operation of covering discs single press whe
38. at spring tab with open end of spring hook facing toward seed hopper b Position spring mount onto upper parallel arm rotate mount forward and position spring onto spring mount tab with open end of spring hook toward seed hopper c Rotate spring down until mount aligns with hole in parallel arm as shown below and install pin Repeat on all row units PLTR27e Pin Location D070799168 D070799169a IS619 NOTE If no till coulters are to be installed install all four down force springs as shown below D07010301 D062603103 Pull Row Unit Push Row Unit NOTE It is necessary for the operator to adjust springs according to field conditions If springs are adjusted for too much down pressure for field conditions it is possible for the row units to lift the planter to the extent that the drive wheels do not make sufficient contact NOTE See instructions supplied with Pneumatic Down Pressure Package for installation of that option 07 Rev 8 07 CLOSING WHEEL OPTIONS IS619 Rubber V And Cast Iron V Rubber V Closing Wheel 700 01070 7279X Cast Iron V Closing Wheel 700 01061 2 A6434 RU83d Closing Wheel Lock Washer x 3 Ya Cap Screw And Lock Nut Shown With Rubber Closing Wheel A10948 Hardware Bag 6 Rows Rubber Wheel 2 A6597 LF212299 15a Cast Iron Wheel Closing Wheel Arm Installation Hardened Washer 14 Bushing
39. d 7 d RE EN ge 36 4 E J Rev 9 11 How Unit 2006 and on ITEM 6 O ON OO oi LA 12 13 14 15 16 i7 18 19 20 21 22 23 24 25 26 27 Rev 9 11 PART NO G10001 G11387 GB0268 G10801 G10315 G10102 GA2054 GB0239 G10102 G10015 GA6619 G10463 G10171 G10232 G10106 GA6620 GA6618 G10303 G11386 G10232 G10106 G10107 GD1109 GD9290 G10018 G10109 G10152 GD3180 12 GD9562 GA6171 GD9305 GA2014 GD10473 G10427 G10006 GD11845 GA6733 GA6801 QTY Per Row MYN NNa NN DD 0 nDNDNDDDNDDAAARAN a a Na Ni Nest 4 N D Covering Discs Single Press Wheel Service Manual DESCRIPTION Hex Head Cap Screw 16 x 1 Flat Washer 3s SAE Wheel Arm Stop Carriage Bolt 12 13 x 214 Carriage Bolt 1 2 13 x 2 Used W Straight Drop In Furrow Granular Chemical Bracket Hex Nut 13 opring Eccentric Bushing Hex Nut 12 13 Adjusting Bolt 13 x 5 Mounting Arm Cotter Pin x 1 2 Hex Head Cap Screw e 18 x 1 Lock Washer 54e Hex Nut 6 18 Bracket Mount Carriage Bolt 6 18 x 1 Flat Washer 56 SAE Lock Washer 54e Hex Nut 6 18 Lock Nut 11 Bushing 64 I D x 7 amp O D x 1 4 Long Disc Blade 8 Hex Head Cap Screw 9 e 18 x 9e Lock Nut 6 18 Grade 8 Hex Head Cap Screw 11 x 9 Sleeve 5 I D x 7 O D x 2 Long Half Wheel Bearing Tire
40. d Bander 1 A8368 Hardware Bag Chain Chain Idler Meter Drive Funnel Hose 4 12 Slope Compensating Bander And Straight Drop In Furrow Placement Components 1 A8367 Hopper And Meter 1 7888X Chemical Hopper Support Package 6 10312 Carriage Bolt 6 18 x 3 4 6 10620 Flange Nut 6 18 1 A10757 Hopper Panel Extension 1 7719X Reflective Decals Package 1 Package Per 2 Rows 18490 D061099206 METR14e The Granular Chemical Hopper With Meter Hopper Panel Extension And Bander is designed for use on the KINZE Pull Row Unit This package includes parts for 4 72 slope compensating banding or straight drop in furrow placement of granular chemical DANGER Agricultural chemicals can be dangerous Improper selection or use can seriously injure A persons animals plants soil or other property BE SAFE Select the right chemical for the job Handle it with care Follow the instructions on the container label and of the equipment manufacturer D06039901 RU143c Granular Chemical Hopper e Be sure the G7100 115 warning decal is in place on the underside of each granular chemical hopper lid 09 Rev 8 07 OPTIONAL ATTACHMENTS IS619 Granular Chemical Hopper With Meter Hopper Panel Extension And Bander STEP 1 Install hopper panel extension onto hopper support as shown below METR14cc 546 18 x 3 4 Carriage Bolts And Flange Nuts STEP 2 Install idler supplied in hardware bag as shown below ME
41. d water or cleaning solution as required e Replace WARNING signs should they become damaged painted over or if they are missing e Check the reflective decals and SMV sign periodically Replace if they show loss of any of their reflective properties e When replacing decals clean the machine surface thoroughly using soap and water or cleaning solution WARNING A to remove all dirt and grease AGRICULTURAL CHEMICALS CAN BE DANGEROUS Part No G7100 115 IMPROPER SELECTION OR USE CAN SERIOUSLY i INJURE PERSONS ANIMALS PLANTS SOIL OR Located on the under side of each OTHER PROPERTY BE SAFE SELECT THE RIGHT granular chemical hopper lid CHEMICAL FOR THE JOB HANDLE WITH CARE FOLLOW THE INSTRUCTIONS ON THE CONTAINER LABEL AND OF THE EQUIPMENT MANUFACTURER 7100 115 Rev 8 07 INTRODUCTION IS619 The KINZE Pull Row Units have been assembled as completely as possible before shipment Read completely through all instructions before beginning assembly Before beginning set up using the shipping order and the contents listings in each instruction check to be sure you have all the packages needed to complete assembly GENERAL INFORMATION The information used in these instructions was current at the time of printing However due to KINZE s continual attempts to improve its product production changes may cause your machine to appear slightly different in detail KINZE Manufacturing Inc reserves the right to chan
42. e filled to prevent accumulation of dust or dirt in seed meter which can cause premature wear See Finger Pickup Seed Meter and or Brush Type Seed Meter Periodically empty hoppers completely to remove any foreign objects and to ensure proper seed meter operation Mechanical seed hopper Disengage meter drive and hopper latch and lift hopper off hopper support See Seed Meter Drive Release SEED METER DRIVE RELEASE S A clutch release mechanism disengages seed meter drive N from seed meter to remove seed hopper Disconnecting drive S n allows operator to check granular chemical application rates amp Disengage SS without dropping seed It also allows one or more rows to be CX disconnected when finishing fields 9 3 Turn knob 1 4 turn counterclockwise to disengage or turn clockwise to engage ROW UNIT EXTENSION BRACKETS How unit extension brackets extend row units rearward 4 to provide clearance for coulter mounted residue wheels and HD single disc fertilizer openers Extension Ne e bracket Extension bracket Row unit extension brackets Rev 9 11 ABA P 9 Row Unit Operation Service Manual Row Unit 2006 and on ROW UNIT CHAIN ROUTING Row unit drive chains must be properly tensioned and aligned for proper operation and to minimize wear Inspect and replace weak worn or broken springs idlers and idler bushings EdgeVac push row unit meter drive Direction of tra
43. e left blank intentionally ROW UNIT ASSEMBLY amp INSTALLATION INSTRUCTIONS SDS Planters w Mechanical Seed Metering IS619 Rev 2 08 Throughout these instructions the symbol A and or the words NOTE IMPORTANT CAUTION WARNING or DANGER are used to call your attention to important information The definition of each of these terms follows NOTE Indicates a special point of information or addresses a machine adjustment IMPORTANT Indicates an operation or maintenance condition which if not corrected could result in damage to machine property crops or the environment A CAUTION Indicates a potentially hazardous situation which if not avoided may result in minor or moderate personal injury A WARNING Indicates a potentially hazardous situation which if not avoided could result in death or serious personal injury A DANGER Indicates an imminently hazardous situation which if not avoided will result in death or serious personal injury 01 Rev 2 08 SAFETY PRECAUTIONS IS619 A Make sure there are no persons near the planter when row markers are in operation Always install all lockup devices and or lower planter to the ground before working under the unit Never clean lubricate or adjust a machine that is in motion Before applying pressure to the hydraulic system make sure all connections are tight and that hoses and fittings have not been damaged Hydraulic fluid escaping under pressure can have sufficient
44. els after adjusting planting depth Initial press wheel down force spring setting is 272 between mounting arm tab and locking nut Loosen 1 2 locking nut and turn adjusting bolt in to increase down force or out to decrease down force Tighten locking nut against spring plug Adjust all row units to a similar setting Locate for staggered or side by side operation _ Eccentric SE bushing aS N BRO Eccentric bushings in the wheel arm stop allow for lateral adjustment of covering discs single press wheel assembly Use a 3 4 wrench to loosen hardware attaching closing wheel arm to wheel arm stop Use another 3 4 wrench to turn eccentric bushings until covering discs single press wheel assembly is aligned with seed trench Tighten hardware Two sets of holes in mounting arm locate covering discs for staggered or side by side operation Five sets of holes in each disc bracket allow 1 2 incremental blade depth adjustment Slotted holes in disc mount and bracket allow for 0 15 blade angle adjustment Adjust covering discs on all row units to similar settings Covering disc adjustments Ange 2 AI 5 Rev 9 11 Row Unit Operation Row Unit 2006 and on Service Manual SEED HOPPERS Mechanical seed hopper has a capacity of 1 9 bushels EdgeVac seed hopper has a capacity of 1 75 bushels Use clean seed and make certain there are no foreign objects inside when filling seed hopper Replace hopper lids after hoppers ar
45. force to penetrate skin Causing injury or infection The seed and fertilizer metering systems of this planter are designed to be driven by ground tires Hydraulic motors power the seed delivery systems The use of aftermarket hydraulic electric or PTO drives may create serious safety hazards to you and others nearby Always follow all appropriate safety standards and practices to protect you and others near this planter from injury Make sure all safety shields are installed correctly The row unit has been designed and built with your safety in mind Do not make any alterations or changes to this equipment Any alteration to the design or construction may create safety hazards P b PP WORK AREA Keep the work area clean and dry Wet or oily floors are slippery Wet spots can be dangerous when working with electrical equipment Make sure the service area is adequately vented Be sure all electrical outlets and tools are properly grounded Use adequate light for the job Be prepared if an accident or fire should occur Know where first aid kits and fire extinguishers are located and know how to use them gt PPP FE SAFETY WARNING SIGNS A The WARNING sign illustrated on this page is placed on the machine to warn of hazards This and other warning found on these signs are for your personal safety and the safety of those around you OBSERVE THESE WARNINGS e Keep these signs clean so they can be observed readily Wash with soap an
46. ge specifications or design without notice and without incurring obligation to install the same on machines previously manufactured Right hand R H and left hand L H as used throughout these instructions are determined by facing in the direction the machine will travel when in use unless otherwise stated RU149 Model 3800 Planter Pull Row Unit Shown With Optional Quick Adjustable Down Force Springs 03 Rev 8 07 MOUNTING BOLTS AND HARDWARE IS619 All hardware furnished with the row unit unless otherwise noted is SAE Grade 5 Grade 5 cap screws are marked with three radial lines on the head If hardware must be replaced be sure to replace it with hardware of equal size strength and thread type Refer to the torque values chart when tightening hardware It is suggested that hardware be left somewhat loose until all parts have been assembled This especially applies to bearing flanges and idler sprockets Then as a final step tighten all hardware to the torque value specified in the chart NOTE Over tightening hardware can cause as much damage as under tightening Tightening hardware beyond the recommended torque range can reduce its shock load capacity Before operating the planter for the first time check to be sure all hardware is tight Check all hardware again after approximately the first 50 hours of operation and at the beginning of each planting season thereafter How U
47. hemical manufacturers instructions Granular chemical clutch drive coupler and meter shaft can be disengaged and engaged by turning throwout knob at rear of hopper support panel Rotate knob 1 4 turn counterclockwise to disengage and 1 4 turn clockwise to engage Slotted holes in hopper support panel and clutch housing allow for alignment adjustment between clutch drive coupler and meter shaft SPRING TOOTH INCORPORATOR Spring tooth incorporator smooths soil behind row unit and incorporates granular chemicals Adjust two mounting chains on each spring tooth incorporator so there is approximately Ye slack in chain when unit is lowered to planting position NOTE Spring tooth incorporator is not compatible with covering discs single press wheel option Spring tooth incorporator Rev 9 11 ge Fs 13 Row Unit Operation Service Manual GRANULAR CHEMICAL BANDING OPTIONS How Unit 2006 and on Granular chemical banding options allow 472 slope compensating banding straight drop in furrow placement or 14 rear banding NOTE Granular chemical rear bander is not compatible with covering discs single press wheel option 14 rear banding GRANULAR CHEMICAL BANDER SHIELD Optional granular chemical bander shield is installed on underside of wheel arm stop to shield crop residue from lodging in granular chemical bander 14 4172 slope compensating bander Azar Straight drop in furrow placemen
48. ins Raise planter and remove spring mount pin at top of spring 2 Slide mount to desired position and install pin NOTE Adjust springs for field conditions Too much down pressure in hard field conditions can cause row units to lift planter and keep drive wheels from making contact Too much down pressure in soft field conditions can cause row unit to run too deep Rev 9 11 NA DEE a 240 7 Row Unit Operation Service Manual Row Unit 2006 and on PNEUMATIC DOWN PRESSURE PACKAGE OPTION How unit down pressure can be adjusted on the go as field conditions change with pneumatic down pressure option A cab mounted control box adjusts pressure Older models may have a digital readout A planter mounted 12 VDC air compressor with 3 gallon capacity air tank supplies air for the down pressure system Packages include upper and lower air spring mounting castings for pull row units front and rear air spring mounting castings for push row units 150 psi rated air springs O D nylon hoses dual solenoid air valve and stainless steel 160 psi 2 liquid filled gauge and planter wiring harness Pneumatic down pressure row unit extension brackets are required in some applications Pull row unit air spring Push row unit air spring NOTE If additional down pressure is needed with the Pneumatic Down Pressure Package assist springs are available through your Kinze dealer One spring is installed on the outer side of the parallel
49. ire replacement of row unit shank assembly 3 Install machine bushing s new disc blade bearing assembly washer and cap screw Torque 11 Grade 5 cap screw to 110 ft lb 149 14 N m NOTE Replace disc blades only with disc blades of equal thickness 4 Install bearing dust cap scraper and gauge wheel HEPLACE BEARING ONLY 1 Remove gauge wheel scraper bearing cap cap screw washer and disc blade bearing assembly 2 Remove 1 rivets from bearing housing to expose bearing 3 Installing new bearing install three evenly spaced 1 4 cap screws into three of six holes in bearing housing to hold bearing and bearing housing in place Install rivets in other three holes Remove 1 4 cap screws and install rivets in those three holes 4 Reinstall disc blade bearing assembly washer and cap screw Torque 11 cap screw to 110 ft lb 149 14 N m 5 Install bearing dust cap scraper and gauge wheel Rev 9 11 ge Fs 17 Lubrication and Maintenance Service Manual How Unit 2006 and on SEED TUBE GUARD INNER SCRAPER Seed tube guard protects seed tube and acts as inner scraper for seed opener disc blades Remove seed tube and check for wear Excessive wear on seed tube indicates a worn seed tube guard Replace seed tube guard if it measures or less at lower end A new seed tube guard measures approximately 7 NOTE No till planting or planting in hard ground conditions especially when planter is not equipped with no
50. ly 12 Tine R H Items 2 4 5 and 18 Wheel Assembly 12 Tine R H Items 4 5 18 and 20 y 3 ne Coulter Mounted Residue Wheels Service Manual How Unit 2006 and on RU104uuu RU153 STYLE A Used With Style A Row Unit Mounted No Till Coulter STYLE B Used With Style B Row Unit Mounted No Till Coulter 60 Rev 9 11 How Unit 2006 and on ITEM I O ON O O1 11 12 13 14 15 16 17 18 19 20 Rev 9 11 PART NO GD1132 G10010 G10503 GD10552 GA5654 GA2014 GA14251 GD10519 311389 G10974 G11098 G11389 G10974 GA7271 GD10526 G10213 GA8760 G10765 G10133 G10109 GD9724 GB0387 GB0401 G11236 GB0383 G11392 G11228 GA14250 G10003 G10229 GA7446 GA7445 GA12236 GA12235 G1K467 QTY Per Row NMMpHpItNNAjAWA ANA a n NN NNN MND a NNa Coulter Mounted Residue Wheels Service Manual DESCRIPTION Dust Cap Hex Head Cap Screw 11 x 3 Hex Jam Nut 11 Grade 2 Wheel 12 Tine x 12 Hub W Bearings Bearing Cam Spring Flat Washer 12 SAE Lock Nut W Nylon Insert 2 13 Hex Head Cap Screw 2 13 x 91 Grade 8 Flat Washer 12 SAE Lock Nut W Nylon Insert 12 13 Mount Sleeve 71 Machine Bushing 9 030 Thick Weed Guard W Spring Pin Spring Pin 1 4 x 1 Hex Head Cap Screw 94e 18 x 112 Lock Nut 6 18 Grade 8 Backing Plate Wheel 12 Tine 3 x 12 Mount Hex Head Cap Screw 34 10 x 101 Bu
51. ly 30 above the floor Install support stands to safely support the planter until assembly is complete STEP 2 Attach lower anchor portion of mounting bracket assembly to row unit face plate Attach lower anchor portion of mounting bracket assembly to row unit face plate using two 1 2 x 1 1 2 cap screws and lock nuts Attach upper portion of mounting bracket assembly using rear hole in the row unit lower parallel arms On each lower parallel arm install one 1 2 x 1 34 cap screw and washer supplied in Hardware Bag through mounting bracket then through hole in lower parallel arm Install bushing and 1 2 lock nut Torque all mounting hardware to 57 ft Ibs RU140a 15 13 x 1 Cap Screw Washer Bushing And Lock Nut 2 13x1 1 2 Cap Screw And Lock Nut N DIRECTION OF TRAVEL 20 Rev 8 07 OPTIONAL ATTACHMENTS IS619 Row Unit Mounted Disc Furrower STEP 3 Install support arm Remove lynch pin from shipping storage position in mounting bracket assembly and slide support arm into place in mounting bracket assembly with the V in the angle pointed forward Install lynch pin to secure support arm in shallowest position See Operator amp Parts Manual for additional information RU98f NN Q N DIRECTION OF TRAVEL SIER S Lynch Pin STEP 4 Support Arm 11 x 4 12 Cap Screw SIEF 5 Dust Cap NS STEP 4 Lock Nut STEP 4 GD7805 Hardened Washer STEP 4 Spacers STEP 4 Install disc blade h
52. nit Parallel Linkage Bushing Bolts Lock Nuts 130 Ft Lbs See Bushings in the Lubrication Section of the Operator amp Parts Manual TORQUE VALUES CHART PLATED HARDWARE Grade 5 Grade 8 Grade 2 Fine Coarse Diameter Coarse Fine Coarse Fine 14 50 In Lbs 56 In Lbs 76 In Lbs 87 In Lbs 9 Ft Lbs 10 Ft Lbs D 5 g is D a D D 15 Ft 23 Ft 26 Ft 33 Ft 37 Ft 25 Ft l i 37 Ft 41 Ft 52 Ft 58 Ft 35 Ft l SW Ft l 64 Ft 80 Ft 310 Ft 50 Ft 80 Ft 90 Ft NiS FE 130 Ft 70 Ft l 110 Ft 125 Ft 160 Ft 180 Ft 130 Ft 200 Ft 220 Ft l 280 Ft 315 Ft 125 Ft I 320 Ft 350 Ft 450 Ft 500 Ft 190 Ft 480 Ft 530 Ft 675 Ft 750 Ft 265 Ft 600 Ft l 670 Ft l 960 Ft 1075 Ft 375 Ft l i 840 Ft i 930 Ft 1360 Ft 1500 Ft 490 Ft 1100 Ft SONE 1780 Ft 2030 Ft 650 Ft l 1450 Ft 1650 Ft 2307 Ft 2670 Ft NLC alke a JEG DE all all 3 a anrovim 3 1 a above values Bolts lubricated prior to installation should be torqued to 70 of value shown on chart GRADE 2 GRADE 5 GRADE 8 04 Rev 8 06 TABLE OF CONTENTS IS619 PULL ROW UNIT Less Closing Wheels Larsnes ed Gees 6 DOWN PRESSURE OPTIONS Quick Adjustable Down Force Springs Package eese 7 Pneumatic Down Pressure Package PENN See Instructions Supplied With Package CLOSING WHEEL OPTIONS Cast Iron V Closing Eee 8 Rubber V Closing
53. ntenance Service Manual Row Unit 2006 and on GAUGE WHEEL ARM BUSHING SEAL REPLACEMENT Gauge wheel arm a bushings seals ab NOTE Gauge Wheel Arm Bushing and Seal Driver Kit G1K296 is available through your Kinze Dealer 1 2 9 6 Hemove gauge wheel from arm Hemove gauge wheel arm from shank assembly Remove seal and bushing and discard Clean and dry inner bore Drive press replacement bushing inside bore of arm to a depth of 125 below flush Coat wiping edge of seal with grease Drive press seal into place with lip to outside NOTE Use extra care to protect the sealing lip during installation Apply uniform pressure to assemble the seal into the bore of the arm Never apply a direct hammer blow to the seal surface f 8 Inspect gauge wheel pivot spindle Reinstall gauge wheel arm assembly and gauge wheel NOTE Use special machine bushing between gauge wheel arm and gauge wheel 9 Shim for proper gauge wheel tire disc blade clearance 10 Lubricate with an SAE multipurpose grease GAUGE WHEEL ARM PIVOT SPINDLE REPLACEMENT 1 16 Hemove gauge wheel and arm assemblies from shank assembly Pivot spindle cap screw Remove 1 2 x 4 cap screw that locks pivot spindle in place and remove spindle Install replacement spindle and position as shown Exact centering is critical Install 1 2 x 34 cap screw and torque to lock pivot spindle in place Install gauge wheel and a
54. or use on pull row units and push row units Row unit extension brackets are required on the four center pull row units if the planter is equipped with coulter mounted residue wheels Weed guard NOTE Opening in weed guard must face down Coulter mounted residue wheels Residue wheels attach to row unit mounted coulter with two cap screws and sleeves allowing unit to free float A 2 position spindle bolt mounting positions wheels interlocked or staggered Depth adjustment is made with a spring loaded cam and pin with 11 positions in 1 4 increments A high point on the cam allows wheels to be locked up A weed guard on the inboard side of each wheel helps prevent weed wrap which can cause premature bearing failure Ange 12 AI 5 Rev 9 11 Row Unit Operation Row Unit 2006 and on Service Manual GRANULAR CHEMICAL HOPPER AND DRIVE WARNING Agricultural chemicals can cause death or serious injury to persons animals and plants or seriously damage soil equipment or property Read and follow all chemical and equipment manufacturers labels and instructions The granular chemical hopper has a 1 4 cubic feet capacity Make sure no foreign objects get into hopper when it is being filled Replace hopper lids after filling to prevent accumulation of dirt and moisture A metering gate on bottom of hopper regulates the application rate See Dry Insecticide and Dry Herbicide Application Rate Charts in this manual Calibrate using c
55. p 2 A9862 Weed Guard W Spring Pin 1 B0218 Bushing 1 A9898 Cam Assembly This package is designed to be installed on the frame mounted coulter attachment DANGER Always install all safety lockup devices or lower machine to the ground before working under or around the machine RU135f pend J STEP 1 Raise planter Replace coulter spindle cap screw Raise the planter to transport position and install all safety lockup devices Remove the x 5 cap screw that attaches the disc blade and replace it with the x 5 1 2 cap screw and bushing supplied in the Hardware Bag Bushing must be installed on L H side of coulter arm Reuse existing lock nut 26 Rev 8 07 OPTIONAL ATTACHMENTS IS619 Residue Wheels For Use On Frame Mounted Coulter STEP 2 Install wheel mount assembly onto frame mounted coulter Install wheel mount assembly onto frame mounted coulter as illustrated below using hardware sleeves and bushings supplied with the wheel mount assembly RU135ii STEP 3 Install cam assembly onto frame mounted coulter Install cam assembly onto frame mounted coulter located as shown above using x 1 34 cap screw supplied in Hardware Bag Reuse existing lock nut STEP 4 Install wheel assembly onto wheel mount Install wheel assembly machine bushings and weed guard onto each side of wheel mount assembly as shown above using x 3 cap screws machine bushings and hex jam nuts supplied in Hardware Bag
56. rm assemblies Shim for proper gauge wheel tire disc blade clearance I Fs Rev 9 11 Lubrication and Maintenance How Unit 2006 and on Service Manual 15 SEED OPENER DISC BLADE BEARING ASSEMBLY NOTICE Excessive blade contact may result in premature disc opener bearing hub failures and excessive wear on seed tube guard inner scraper When properly adjusted if one blade is held in fixed position opposite blade should rotate with less than 5 pounds force at outer edge of blade Maintain approximately 1 172 of blade to blade contact to properly open and form seed trench As blade diameter decreases due to wear it is necessary to relocate machine bushings from inside to outside to maintain 1 172 of contact Approximately 1 172 blade to blade contact NOTE Replace blades If proper blade to blade contact cannot be maintained after relocating machine bushings or if blade diameter wears below 1472 REPLACE DISC BLADE BEARING ASSEMBLY NOTE Only bearing may need to be replaced if there is excessive endplay or if bearing sounds or feels rough when disc blade is rotated 1 Remove gauge wheel scraper and bearing dust cap 2 Remove cap screw washer and disc blade bearing assembly Machine bushings between shank and disc blade are used to maintain approximate 1 1 of blade to blade contact NOTICE Left hand side of opener uses a left hand threaded cap screw DO NOT OVER TIGHTEN Damage to shank threads requ
57. row units only Springs provide down pressure on coulter for maximum penetration while exerting less shock load on row unit Initial coulter blade location is in top hole Relocate blade to one of lower two holes 1 increments as wear occurs or for deeper blade operation Blade depth adjustment holes Frame mounted coulter adjustment DOWN PRESSURE ADJUSTMENT NOTICE Excessive down pressure can damage coulter components when coulter strikes an obstacle Do not set down pressure higher than needed for consistent soil penetration Raise planter Turn spring adjustment bolts clockwise to increase or counterclockwise to decrease down pressure Set both springs to specification shown in following table Frame Mounted Coulter Spring Downpressure Settings End flush with spring Extended 1 2 through All threads used anchor bar spring anchor bar 275 Ib 124 7 kg 400 Ib 181 4 kg 500 Ib 226 8 kg RESIDUE WHEELS FOR FRAME MOUNTED COULTER PR AR be tge ae A NOTE Opening in weed guard must face down NOTICE Tined wheel forward mounting positions cannot be used behind 3600 axles due to limited cklearance Residue wheels attach to frame mounted coulter with two cap screws and sleeves allowing the unit to free float A 2 position spindle bolt mounting positions wheels interlocked or staggered Depth adjustment is made with a spring loaded cam and pin with 11 positions in 1 4 increments A high poin
58. shing 1 O D x 2 2 1 D x Long Flat Washer 34 SAE Lock Nut 10 Locking Pin Hex Head Cap Screw 16 x 11 2 Lock Washer Wheel Assembly 12 Tine R H Items 3 4 14 and 15 Shown Wheel Assembly 12 Tine L H Items 3 4 14 and 15 Wheel Assembly 12 Tine R H Items 4 14 15 and 16 Shown Wheel Assembly 12 Tine L H Items 4 14 15 and 16 Residue Wheel Mount Kit Items 17 20 y 3 a Frame Mounted Coulter W Residue Wheels Service Manual Row Unit 2006 and on RU135c RU135g RU153b RU135hh With Residue Wheels Q sr E se EI Y i oss 62 KE DE Rev 9 11 Frame Mounted Coulter W Residue Wheels Row Unit 2006 and on Service Manual ITEM PART NO QTY DESCRIPTION Per Row 1 311010 2 Hex Head Cap Screw 10 x 12 2 GA9844 1 Plate W Angle 3 G10039 4 Hex Head Cap Screw 2 13 x 194 4 GA9131 1 Coulter Frame 5 310007 4 Hex Head Cap Screw 11 x 11 2 310107 4 Lock Nut 11 6 G10400 1 Hex Head Cap Screw 10 x 61 G10112 1 Lock Nut 10 7 GD12826 1 Spring Anchor Bar 8 310574 4 Carriage Bolt 12 13 x 1 310111 4 Lock Nut 12 13 9 GD12827 2 Adapter 10 GA8641 1 Hub W Bearing and Retaining Ring GA8603 1 Bearing Double Row GD11652 1 Retaining Ring 276 11 GD7803 1 Disc Blade Fluted 1 8 Flutes Shown GD7804 Disc Blade Bubbled 1 GD9254 Disc Blade Fluted 94 13 Flutes 12 GB0213 2 Spring Seat 13 GD12817 2 Compression Spring 14 G
59. t Bander shield Wheel arm stop 3 16 x 1 hex head cap screw Granular chemical bander shield installation Rev 9 11 a ST bl n Lubrication and Maintenance How Unit 2006 and on Service Manual CHAIN TENSION ADJUSTMENT Drive chains have spring loaded idlers and are self adjusting Hemove link to shorten chain if wear stretches chain and reduces spring tension Check idler pivot points to make sure they rotate freely See Wrap Spring Wrench Assembly in this section for additional information Additional chain links are stored inside planter frame DRAG CLOSING ATTACHMENT Inspect each drag closing attachment and replace any worn or broken parts before storing planter Check for loose hardware and tighten as needed Drag Closing Attachment GAUGE WHEEL ADJUSTMENT Shim gauge wheel to lightly contact opener disc blade Check adjustment in field position Gauge wheel adjustment Gauge wheels should lightly contact opener blades to prevent accumulation of dirt or trash Gauge wheels and opener blades should turn with only slight resistance Add or remove machine bushings between shank and gauge wheel arm to adjust clearance between gauge wheels and opener blades Store remaining machine bushings between gauge wheel arm and flat washer on outer side of gauge wheel arm NOTE It may be desirable to space gauge wheel further from blade when operating in sticky soils Rev 9 11 ge Fs 15 Lubrication and Mai
60. t 2 13 Leveler Blade Carriage Bolt 6 18 x 1 Flat Washer 56 SAE Lock Nut 6 18 Grade 8 Hex Head Cap Screw 13 x 34 Flat Washer 2 SAE Lock Nut 2 13 y 3 x Row Unit Mounted Disc Furrower Service Manual Row Unit 2006 and on IP1284 O 19 0 T ge 99 ae GI od SE IL EN ge 56 4 E J Rev 9 11 Row Unit Mounted Disc Furrower Row Unit 2006 and on Service Manual ITEM PART NO QTY DESCRIPTION Per Row 1 GA5719 1 Mounting Bracket 2 GD7890 2 Link 3 GA5715 1 Anchor 4 G10017 2 Hex Head Cap Screw 2 13 x 11 2 G10111 2 Lock Nut 13 5 GA5718 1 Support Arm 6 GD7817 01 2 Spacer 16 1 D x 34 Long 7 GD7817 04 2 Spacer 11 6 I D x 7 Long 8 310572 12 Truss Head Slotted Machine Screw 94e 18 x 7 G10106 12 Hex Nut 6 18 9 GD7823 Disc Blade Solid 12 Shown GD8307 Disc Blade Notched 12 10 GA5654 2 Hub W Bearings GA2014 Bearing 11 GD1132 2 Dust Cap 12 310318 2 Hex Head Cap Screw 11 x 41 G10107 2 Lock Nut 11 G11391 2 Flat Washer SAE 13 G11389 2 Flat Washer 12 SAE G10017 2 Hex Head Cap Screw 2 13 x 17 G10111 2 Lock Nut 2 13 14 G10585 1 Hex Head Cap Screw 1 2 13 x 3 311389 2 Flat Washer 2 SAE G10111 1 Lock Nut 2 13 15 G10536 1 Detent Pin 1 2 x 212 Grip 16 310039 2 Hex Head Cap Screw 12 13 x 1 G10111 2 Lock Nut 2 13 17 G11389 2 Flat Washer 1 2 SAE 18 GD7889 6 Bushing 1 O D x 6 1 D x e Long
61. t on the cam allows wheels to be locked up A weed guard on the inboard side of each wheel helps prevent weed wrap which can cause premature bearing failure Rev 9 11 ge Fs 9 Row Unit Operation Service Manual Row Unit 2006 and on ROW UNIT MOUNTED DISC FURROWER PULL ROW ONLY Disc furrowers are used to clear crop residue dirt clods and dry soil from in front of row units for a clean and smooth seed bed The disc furrower may be equipped with 12 solid blades or 12 notched blades Notched blades are for heavier residue conditions and cut crop residue and move it aside to prevent plugging or pushing Set soon Lynch pin x Slotted holes OOOoOooGoc 7 Dust cap Disc furrower adjustment Vertical adjustment can be made in 1 increments Remove lynch pin in vertical support arm and move arm up or down Reinstall lynch pin Finer adjustment can be made by removing lynch pin and using x 214 set screw to clamp support arm in position Slotted holes in support arm allow front to rear disc blade adjustment Blades can be adjusted so front edges meet or cutting edge of one blade overlaps edge of other blade NOTE Dust cap must be removed to make adjustments ROW UNIT MOUNTED BED LEVELER PULL ROW ONLY NOTE Row unit mounted bed leveler is not compatible with row spacings less than 36 1 FA 08 Vertical adjustment can be made in 1 increments Remove lynch pin in vertical support arm and move arm up or do
62. ting Bracket 1 A5719 Mounting Bracket 1 A5897 Hardware Bag 1 A5897 Hardware Bag 2 D7817 01 Spacer 3 4 2 D7817 04 Spacer 1 2 2 10039 Cap Screw 2 13 x 1 94 2 10318 Cap Screw 11 x 4 1 2 2 D7805 Washer 95 2 10107 Lock Nut 11 2 D7889 Bushing 2 10111 Lock Nut 13 2 2 D7817 01 Spacer 3 4 2 D7817 04 Spacer 1 2 2 10039 Cap Screw 12 13 x 1 94 2 10318 Cap Screw 11 x 4 1 2 D7805 Washer 95 2 10107 Lock Nut 11 2 D7889 Bushing 2 2 10111 Lock Nut 13 D14674 Special Washer 12 Hardened 2 D14674 Special Washer Hardened Dust Cap Solid Disc Hub Assembly 10106 Hex Nut 54e 18 10572 Slotted Machine Screw D7823 Solid Disc Blade A5654 Hub Assembly 2 D1132 2 A5655 Dust Cap 6 10106 Hex Nut 546 18 6 10572 Slotted Machine Screw 1 D8307 Notched Disc Blade 1 A5654 Hub Assembly Notched Disc Hub Assembly The row unit mounted disc furrower may be equipped with either 12 solid or 12 notched disc blades One package is required per row DANGER Always install all safety lockup devices or lower machine to the ground before working under or around the machine LF212299 22 61658 37 Shown With Solid Disc Blades Shown With Notched Disc Blades 19 Rev 8 07 OPTIONAL ATTACHMENTS IS619 Row Unit Mounted Disc Furrower STEP 1 Install support stands Raise the planter until the bottom of the toolbar is approximate
63. ub assembly Using x 4 1 2 cap screws hardened washers GD 7805 12 and 3 4 spacers and lock nuts from Hardware Bag install disc blade hub assembly onto each side of V angle Disc blades can be installed edge to edge or with R H or L H blade leading If using leading set up use an equal number of R H and L H attachments to minimize draft Adjust all blades equally and torque mounting hardware to specs See Operator amp Parts Manual for additional information STEP 5 Install dust cap onto each hub assembly STEP 6 Remove support stands and lower planter to the ground 21 6 05 OPTIONAL ATTACHMENTS IS618 Row Unit Mounted Residue Wheel A12685 Row Unit Mounted Residue Wheel 700 01064 A12685 The row unit mounted residue wheel attachment is installed in front of the pull row unit One package is required per row DANGER Always install all safety lockup devices or lower machine to the ground before working under or around the machine STEP 1 Attach row unit mounted residue wheel attachment to row unit face plate Raise the planter until the bottom of the toolbar is approximately 30 above the floor Install support stands to safely support the planter until assembly is complete Attach row unit mounted residue wheel attachment to row unit face plate using 1 2 carriage bolts and lock nuts supplied with the attachment STEP 2 Center residue wheel ahead of double disc openers and torque bolts to 57 ft Ibs ST
64. unit extension brackets Order Code 700 01072 for 1 row are required on all inner and outer wing row units DANGER Always install all safety lockup devices or lower machine to the ground before working under or around the machine 17 Rev 8 07 OPTIONAL ATTACHMENTS IS619 Coulter Mounted Residue Wheel STYLE A Coulter Mounted Residue Wheels Attachment STEP 1 Assemble wheels on arm Install R H and L H wheel assemblies interlocked or staggered onto mount assembly using x 3 cap screws machine bushings between wheel and weed guard weed guard hex jam nuts and dust caps supplied in the Hardware Bag Torque cap screws to 110 ft lbs Tighten jam nuts securely NOTE Opening in weed guard must point down RU104r STEP 2 Install wheel arm assembly on coulter arm Raise the planter to transport position except 3140 and install all safety lockup devices Insert 7 1 2 sleeve into welded sleeves on notill coulter arm Attach the mount assembly onto the no till coulter arm using the 2 x 9 1 2 cap screw 1 2 hardened washers and 1 2 lock nut supplied with the mount assembly Torque hardware to 57 ft Ibs Welded Sleeves STYLE B Coulter Mounted Residue Wheels Attachment STEP1 Assemble wheels on arm Install R H and L H wheel assemblies interlocked or staggered onto mount assembly using x 3 cap screws machine bushings between wheel and weed guard weed guard hex jam nuts and dust caps
65. utches must be removed from planter for cleaning If system is not equipped with Pneumatic Down Pressure air clutches can be disassembled and cleaned on planter At each row unit 1 Remove meter assembly 2 Press down collar on air fitting and remove air hose 3 Loosen tension from chain and remove from air clutch sprocket 4 Loosen lock clamp and slide clamp washer and air clutch away from chain 5 Use a e wrench and remove sprocket from air clutch assembly 6 Remove small Phillips head screw from side of air clutch housing and remove housing cover 7 Expand retaining ring and remove from assembly 8 Remove and separate sprocket hub ratchet gear clutch spring and hex bushing from air clutch housing 9 Remove debris and dirt from clutch components Clean parts with brake cleaner or equivalent cleaner 10 Make sure parts are completely dry Lubricate sprocket hub ratchet gear clutch spring and hex bushing with silicone spray 11 Reverse procedure to assemble air clutch assembly 12 Place one drop of pneumatic or light duty hydraulic oil in air cylinder fitting before attaching air line 13 Install meter assembly Eu rd Rev 9 11 f AP 3 21 Troubleshooting Service Manual Row Unit 2006 and on AIR CLUTCH PROBLEM POSSIBLE CAUSE SOLUTION Clutches slip effected row does not Plunger in cylinder seized Remove air line and lubricated with pneumatic plant or skips or duty hydraulic oil Worn Worn
66. v 8 07 OPTIONAL ATTACHMENTS Frame Mounted Coulter STEP 3 Reinstallhub blade assembly into the coulter arm Reinstall hub blade assembly into the coulter arm using the top hole Torque to 120 ft Ibs STEP 4 Remove the attaching plate w angle Remove the attaching plate w angle from the coulter assembly NOTE A portion ofthe angle onthe attaching plate will need to be trimmed on the first row out from each wing hinge on 3650 planters as shown below A9844 M NM Trim 5 1 2 R H Side Shown STEP 5 Install coulter assembly Using an overhead crane or hoist position the coulter assembly onto the row unit mounting support plate Slide the attaching plate w angle up in between the toolbar and the existing row unit mounting support plate Install the four Y 13 x 1 hex head cap screws STEP 6 Center coulter blade with row unit V opener disc blades and tighten mounting bolts evenly Torque mounting bolts to 57 ft Ibs 24 LF083002101 D03210203a D03060306a IS619 Rev 8 07 OPTIONAL ATTACHMENTS Frame Mounted Coulter FRAME MOUNTED COULTER OPERATION LF083002101 Frame mounted coulters with 1 bubbled 1 fluted 8 flutes or 94 fluted 13 flutes blades may be used on pull row units only Not compatible with push row units The frame mounted coulter is designed to apply necessary spring down pressure on the coulter for maximum penetration while exerting less shock load on
67. v 9 11 STYLE A PART NO G10574 G10111 GA5625 G10036 G10107 G10574 G10111 GD11677 GA8641 GA8603 GD11652 GD7803 GD7804 GD9254 GD14398 GA11520 QTY Per Row mm EE EE STYLE B DESCRIPTION Carriage Bolt 2 13 x 1 Lock Nut 2 13 Arm Style A Hex Head Cap Screw 11 x 4 Lock Nut 11 Carriage Bolt 12 13 x 114 Lock Nut 2 13 Adapter Hub W Bearing and Retaining Ring Bearing Double Row Retaining Ring 276 Disc Blade Fluted 1 8 Flutes Shown Disc Blade Bubbled 1 Disc Blade Fluted 34 13 Flutes Spacer Arm Style B y 3 ee Row Unit Mounted Bed Leveler Service Manual Row Unit 2006 and on IP1283 Ange 54 4 E J Rev 9 11 How Unit 2006 and on ITEM oat WN CO N 10 11 12 13 Rev 9 11 PART NO G10536 G10597 G10503 GA5719 GD7889 G10039 G11389 G10111 GD7890 GA5715 G10017 G11389 G10111 GA5892 GD8266 G10303 G11386 G10109 G10585 G11389 G10111 QTY Per Row N ORAON ANA lt a NNNNO a a a Row Unit Mounted Bed Leveler Service Manual DESCRIPTION Detent Pin 12 x 212 Grip Square Head Set Screw 11 x 21 4 Hex Jam Nut 11 Grade 2 Mounting Bracket Bushing 1 O D x 6 I D x e Long Hex Head Cap Screw 2 13 x 1 Flat Washer SAE Lock Nut 2 13 Link Anchor Hex Head Cap Screw 13 x 17 Flat Washer SAE Lock Nu
68. vel o bE Closed end NOTE Install connector link with closed end facing direction of travel Row unit granular chemical drive NOTE Reverse idler when worn on one side for extended use Es 4 If Fa nee Row Unit Operation How Unit 2006 and on Service Manual QUICK ADJUSTABLE DOWN FORCE SPRINGS OPTION STANDARD OR HEAVY DUTY Standard and heavy duty quick adjustable down force springs are available in increase penetration in hard soil and keep row unit from bouncing in rough field conditions Two springs per row one on each side parallel arms are used unless equipped with row unit mounted no till coulters Row unit mounted no till coulters require four springs per row Position 1 Least Position 2 Position 3 There are four positions to set down pressure spring tension 1 Standard and Heavy Duty Spring Down Force Pressure Position 4 Most 2 Springs 4 Springs Position Standard Heavy Duty Standard Heavy Duty D8249 D21337 D8249 D21337 1 41lb 18 6 kg 43 Ib 19 5 kg 74 Ib 33 6 kg 80 Ib 36 3 kg 2 73 Ib 33 1 kg 86 Ib 39 0 kg 120 Ib 54 4 kg 144 Ib 65 3 kg 3 136 Ib 61 7 kg 167 Ib 75 7 kg 255 Ib 115 7 kg 307 Ib 139 3 kg 4 207 Ib 93 9 kg 249 Ib 113 0 kg 369 Ib 167 4 kg 470 Ib 213 2 kg Pressure does not include weight of row unit seed or options NOTICE Springs must be installed with open side of spring hooks toward seed hoppers to prevent binding on spring mount adjustment p
69. wer settings See Row Unit Mounted No Till Coulter in Row Unit Operation section of this manual Replace 16 diameter coulter blade when worn to 1412 Rev 9 11 ge Fs Service Manual Row unit mounted disc furrower Row unit mounted no till coulter 19 Lubrication and Maintenance Service Manual How Unit 2006 and on COULTER MOUNTED RESIDUE WHEELS Wheel hubs are equipped with sealed bearings If bearings sound or feel rough when wheel is rotated replace them ROW UNIT MOUNTED RESIDUE WHEEL Wheel hub is equipped with sealed bearings If a bearing sounds or feels rough when wheel is rotated replace them GRANULAR CHEMICAL ATTACHMENT Before storing planter disengage granular chemical drive by rotating throwout knob 1 4 turn counterclockwise Remove drive chain and empty and clean all granular chemical hoppers Clean drive chains and coat them with a rust preventive spray or submerge chains in oil Inspect and replace worn or broken parts Install hoppers and chains Check chain alignment SPRING TOOTH INCORPORATOR Before storing planter inspect each spring tooth incorporator and replace worn or broken parts Check for loose hardware and tighten as needed Spring tooth incorporator EN ge 20 AI J Rev 9 11 Lubrication and Maintenance How Unit 2006 and on Service Manual AIR CLUTCH CLEANING Yearly at end of planting season NOTE If system is equipped with Pneumatic Down Pressure air cl
70. wn Reinstall lynch pin Finer adjustment can be made by removing Slotted lynch pin and using x 2 set screw to clamp support arm holes behind in position blades in support Slotted holes in support arm allow blade adjustment Blades oo can be tilted up or down Bed leveler adjustment EN ge 10 AI J Rev 9 11 Row Unit Operation Row Unit 2006 and on Service Manual ROW UNIT MOUNTED RESIDUE WHEEL How unit mounted residue wheels are used on pull and push row units Row Unit Mounted Residue Wheel Two adjustable springs on each residue wheel parallel links provide down force adjustment Position 1 provides minimum down pressure and position 3 maximum down pressure Position 1 Least Position 2 Raise row unit and reposition springs to adjust down pressure an Wheel depth adjustment Wheel angle adjustment Wheel lock up A full threaded bolt and jam nut located on the upper link sets maximum depth for loose soil conditions Initial setting is 194 above row unit double disc opener depth Three holes in upper link adjust wheel angle With wheel mount in most vertical position using the rear hole in the upper link the residue wheel is most aggressive Moving wheel mount to a forward hole reduces aggressiveness of residue wheel for use in mulch till applications where soil is loose To lock residue wheel up remove 1 2 x 5 lockup bolt raise residue wheel and install bolt Eu rd Rev 9 11 f

Download Pdf Manuals

Related Search

Related Contents

IP Camera  Lite-On 52x Max CD-ROM Drive  

Copyright © All rights reserved. Failed to retrieve file