Home

Falcon 3 145, 170, 195 and Tandem Falcon 4 145, 170

image

Contents

1. w TL LS N ri ND Falcon 3 145 170 195 and Tandem Falcon 4 145 170 195 Owner Service Manual June 2015 w TL LS N Ari ND Falcon 3 145 170 195 and Tandem Falcon 4 145 170 195 Copyright 1994 through 2015 by Sport Kites Inc dba Wills Wing Inc All rights reserved No part of this manual may be reproduced in any form without the express written permission of Sport Kites Inc dba Wills Wing Inc June 2015 First Edition 500 West Blueridge Ave Orange CA 92865 Phone 714 998 6359 FAX 714 998 0647 http www willswing com E mail comments willswing com Contents os UO u A PERE CE O usss 1 Disclaimer And Warning NEEN 2 Technical Information And Placarded Operating Limitations 3 A Note About Platform Towing 6 A Few Notes About The Falcon 3 Tandem 6 A Note About High Duty Cycle OperationS mmm 7 A Note About Parts Replacement and Parts Interchangeability 7 Glider Owner s Manual Addendum Falcon 3 4 Sport 2 and U2 8 Falcon Breakdown Procedure For Shipping And Reassembly Procedure 9 Falcon Set Up elei lt 11 Launching And Flying The Falcon 23 ISIC WIND Til u s n ss 23 Trimming Your Glider Ii PITON E
2. CALS 3 10044 S6 y YOO e4 00 Gil J 10044 S6 y UO9 By u36u OWEN 3Jed 9L S 0 WWE 0 x WUIQS 9606 l 91 904 Die X WW S SILI l 91 904 Uuo x ull S COL l 91 904 WWE 0 x uugG 981 ALO auBiew 81493 uu y bua SS DEE E DE MAN uod e NOSYVdd VIQc ele 00 0 1 JALY GOT y L 3 7490 866 659 866 PLZ XVdlHd e S98Z6 VI 39NVHO e JAY 3901143018 005 A EE 03SIA38 Wu 01 1N3n200 QI 4M00TS g ao Get y WOR 9 JN LAR 651 UA NOISIA38 3 ILLE cl OLI pnis u 11eg joer Nose NINO NOLLOS 61 SC NAHL 8E SR EC T 777777 7 7 7 U U P T x ER EDS SC l 001 i m r g9 I H to Le EL SE c9 hl 9 vb 994 S6 y UO9 By ALS Jpal day y UOD e4 ALS PPlwW 9ay y UOd e4 l 91 S 0 uuo Q0 x Wey pv 9 l 91 S 0 Up X WWyy CSI 91 S 0 Up 0 X WWyy 6cc 91 S 0 Uuo 0 x WWyy SII j KD NTE 214928 WW y16u37 Ge DEE EE E DEE DEE CO tb ALS 1U0J 3 p u02 eJ y1bua7 OWEN 1Jed 191 MAN uod e NOSY dd ALOG UL Y 00 0 1 JALY GOT y L 3 790 866 6689 9686 PLZ XVdlHd e G9826 VI J9NVHO e JAY 390183018 005 I EE GESEIS Wun 01 1N3200 QI 4M00TS Jeqx Ser y uord o IA SST NOISIA38 ALLL 08 28 10 pea73sul 09720 se uegssoud ayi K 398eJ44029UL Y UOSLADY 930N NAHL SZ 88H SL nHul 6T 8 OS I 8 Z6 00 29 ONE KL ZE Lr 8r 0 91 S 0 wu6 0 x umog g ST 00 29 Seelen JeqX GGT p uoo ej 200 91 9404 uu6 0 x ung
3. S 0S I 08 SOL 00 02 QU E 0079 be sdno 8q une ULM A S Q z X une 001 IS 080 002 ALS JAX O T UOD Py x 00 v4 pJeoquI Jeqx O I UOD Pj u135ue OWEN 1484 ue pueogino 4eqy O T uoo ej EN OWEULUL uod e NOSUVId L002 T 1T 2002 0671 VN JN 361 YOOLES 490 866 6569 866 PLZ XVAIHA e G9826 VI JONVEO e JAY 39QIu3018 DOS Ad SALVLS Q3SIA3M MM ad GI LN3AK90G OT 3Mddis a ebpe Bulpea7 ser uoolej fo v D ts I NOISIASY ZUM L0900 LI L6900 61 Uo 00 7SI Ug 01 32 D s or 91 91 S 0 l WW 9t0c G 08 2qni 4 deoq Sol UOo e o1 9o 91 G 0 UG wu 0 29 0070 ZALS OLPPL 31 20011 get uo3 ej ECHO 01 G 0 uu6 uu S G602 EE ALS OLPPLU 31 YOU SET uo3 ej Oo c r M 9 S 0 uu6 uu S G602 EE qni 31 1u044 S6T uoo ej BBBHBHB PS CF GE SE UNE ae gg 790 866 66 9 866 rl XV3IHd e G98c6 VI 3DNVHO e JAV 390183018 005 hg SNLVLS 35138 NMVeO 01 IN3MNIOO QI 4Maqq1s oi GET Wd fn v As ATI Es NOISIA38 3 1111 4 Bu1l1S Jebuo WEN 0102 01 8 9 vrl 9 Us Te 0S8 Sr W NAHL 61 A NAHL OOOO AS ee Pye e o 0072 g K uo u0330q 61 00 v ed I c 9 sa oy 20 uo33qnq puaepue3 sS LO 9 e9 TZ EL EH EN 9 G 0 Wie mei 0044 Jtay GET uo3 ej 1 GN 91 G 0 8T e9 9 ou 1993 GBT voa I IT O 91 8 0 ST 0
4. The Falcon 3 and 4 models have superior aerodynamic performance to that of the corresponding Falcon 1 models especially at the lower end of the speed range On average a given size Falcon 3 or Falcon 4 will have a 2 mph lower stall speed with the same pilot weight as the corresponding Falcon 1 This allows a heavier pilot to achieve the same or better sink rate on the same size of the Falcon 3 4 A minimum USHGA Novice II level of pilot proficiency 1s required to fly the Falcon safely unless under the direct supervision of a qualified instructor Operation of the glider by unqualified or under qualified pilots may be dangerous Operating the Falcon outside of the above limitations may result in injury and death Flying the Falcon in the presence of strong or gusty winds or turbulence may result in loss of control of the glider which may lead to injury and death Do not fly in such conditions unless you realize and wish to personally assume the associated risks Wills Wing is well aware that pilots have and continue to perform maneuvers and fly in conditions which are outside the recommended operating limitations stated herein Please be aware that the fact that some pilots have exceeded these limitations in the past without dangerous incident does not imply or insure that the limitations may be exceeded without risk We do know that gliders which meet all current industry standards for airworthiness can and do suffer in flight
5. and the center hinge bolt and nut At the nose Check the security of all nuts at the noseplate and check the top front wire Check that the keyhole tang safety 1s properly secured that the button lock is in place and that the nose cone is properly installed Laying the glider down flat Once the glider is assembled it can easily be laid down flat on the ground l Disengage the nose cone from the bottom surface attachment press upwards on the nose tang button lock and disengage the keyhole tang by pulling down on the nose plate while pressing forward on the tang handle 2 Rock the glider forward so that the basetube folds rearward and underneath the glider as you gen tly lower the glider to the ground Reverse the procedure to set the glider upright again e FA Setting the glider up flat on the ground In areas where the ground is not rocky and when there are strong winds you may wish to set up the glider flat on the ground This is easy to do and relatively few parts of the set up procedure are differ ent from what has been described 1 After unfolding and securing the control bar flip the glider over right side up with the control bar still flat under the glider and folded to the rear 2 Spread the wings attach the bridle ring and install all the battens and the washout tips Note Perform all the normal preflight operations as described above 3 Tension the crossbar 4 When ready raise the nose of
6. least and greatest allowable distances whether variable through tuning or through in flight variable geometry from the line joining the leading edge nose bolts to a he xbar center ball center 48 75 25 b The pilot hang loop 066 75 1 5 Sail Dimensions a Chord lengths at 1 3 ft outboard of centerline 92 2 3 ft inboard of tip 47 D Span extreme tip to tip 392 Location of Information Placard Keel Location of Test Fly Sticker Keel Recommended Pilot Weight Range 175 275 Recommended Pilot Proficiency USHGA Novice HGMA COMPLIANCE VERIFICATION SPECIFICATION SHEET GLIDER MODEL Falcon 3 Tandem MANUFACTURED BY Wills Wing Inc All dimensions in inches weights in pounds NOTE These specifications are intended only as a guideline for determining whether a given glider is a certified model and whether it is in the certified configuration Be aware however that no set of specifications however detailed can guarantee the ability to determine whether a glider is the same model or is in the same configuration as was certified or has those performance stability and structural characteristics required by the certification standards An owner s manual is required to be delivered with each HGMA certified glider and it is required that it contain additional airworthiness informa tion Weight of glider with all essential parts and without coverbags and nonessential parts 1 lbs Leading Edge Dimensions a Nose plate anchor
7. 0 WWE 0 X ully KD 446 L M DIER uu u36ue SN Si u36u 1 pnis uazqeg yoo uo44ng L9 gS MHL 86 or Oooo TA d KC j ke gg 00 I _ SW Sy 1 PU E 9 80I ALS J J aay y UOd e4 ALS 9 ppiu 9ay y UOd e4 ALS JUOJJ 99N y UOD PY 993 GYI y UO2 j OWEN ued 1790 866 66 9 866 vLZ XV4 Hd e 59876 VI 39NVHO e JAY 390143019 00S ae opt y volea C IDA qe Lg iiie Mee RE Wo iid LL CE LV90 866 66 9 866 VIZ XVJlHd e 59876 VI 39NVH0 e JAY 390143019 006 Ag SALVIS 0351138 NMV40 UI 1N3WHN900 QI 3M001S d 4eqX SPI y U03153 Lo JN E 571 YEARS NOISIA38 TELA NAHL SZ Se OCI NHL 61 8 net EL 96 or zo sewoweoxwe lr 02 0g AIS pueogang sw pt y wooed z 1 un 913 01 w6 0x ug Sbz G 96 Jeqy Spp p uooje 1 AO 1LUD LOM e 14918 N wu u1bue y1bu97 OWEN ued I MAN uod NOSYVdd VIQc ele 00 0 1 VN j41V O I y 4 790 866 6G 9 966 PLZ XVdlHd e S98Z6 VI J9NVHO e JAY 390183018 005 A EE 03SIA38 Wu 01 1N3n200 QI 4M00TS 9bp3 Butpe 3u044 O T y uo3 ej OSN EAA STE NOISIA38 ra TL 2961 00 71 6U Q 1018 09 2 NAHL 6U oe 00 61 NAHL S Sle 206 Y 3nu LJ qunou Les 00 T I 290 91 S 0 uug 0 x uuog 8e0z S208 I 920 91 S 0 u 6 0 x uuzg T8 RG J 4eoy O I y uO2 ed ALS pDiu 3 lu044 OZI y UO9 By 00 v CALS 3 10044 0 1 y UO9 Py 0S Gel J1 14043 O I y UO9 8y y1bua7 WEN 1Je
8. 3 so if you have not pur chased the Falcon 3 Shortpack Bag Box you will need to acquire these tools separately Breakdown batten couplings In order to shortpack the Falcon 3 145 170 and 195 to their minimum lengths it 1s necessary to break down the longest battens In order to be able to do this the battens must be modified by installing a threaded coupling at one foot forward of the rear ends of the battens Follow the instructions here to make this modification If you did not purchase the Shortpack Bag Box you can contact Wills Wing to obtain the required couplings We include 2 sets of breakdown batten couplings to retrofit the no 6 battens on the Falcon 3 145 and 4 sets of batten couplings to retrofit the no 5 and 6 battens on the Falcon 3 170 and 195 Each cou pling set consists of the following two parts 10N 2034 BATTEN STUD THREADED INSERT 10MM 0 335 X 2 0 X M7x1 0 10N 2031 BATTEN TIP THREADED INSERT To install the couplings mark and cut the no 6 F3 145 or no 5 and no 6 F3 170 195 at 12 inches from the aft cut edge of the tubing fig 1 Deburr the edges of the tubing Thread the insert complete ly onto the stud and mark the center of the assembly fig 2 Fig 1 Fig 2 Insert the coupling assembly with the stud in the front portion of the batten to the midpoint of the as sembled coupling Mark the batten tubes at positions corresponding to the midpoint of the stud in the front section about 1 2 inch from
9. 917 096NV 1331S u3HSVM OvII fOI Z 9 CC CO D HL uez wer 2 gt Hr 430 NIS vort 3St y v eld leaym Le uepue uoo ej v zoee 902 z SU M Le uepue uosle G O AoA V I22l 80v T 2 1ex2eJg Loo Wood Le uepue uoojej v TOEE D0Z T I
10. A generally use only water and a soft brush You may clean small spots or stains with any commer cial spot remover that is labeled for use on polyester Such cleaning agents are available at the supermarket or drug store or you may order a cleaning solution from Wills Wing through your dealer A note about cables and cable maintenance The cables which support the glider s airframe are critical components of the glider s structure and must be maintained in an air worthy condition It is a general practice in the design of aircraft struc tures to design to an ultimate strength of 1 5 times the highest expected load in normal service Hang glider cables like other structural components on the glider are typically designed with a structural safety factor of only about 50 above the expected maximum load No significant loss in cable strength can be tolerated A cable with even a single broken strand must be replaced before the glider is flown again A cable which has been bent sharply enough to have taken a permanent set will not lie flat in a straight line when all tension is removed must also be replaced immediately If it is not subsequent tensioning and de tensioning of the cable will induce fatigue and the cable will fail In tests we have conducted a cable bent one time to 90 degrees and then loaded to the equivalent of a normal flight load 100 times corresponding to 100 or fewer flights failed at only 56 of its
11. Crossbar attachment hole 139 2 Rear sail attachment point 228 5 229 25 b Outside diameter at 1 Nose 209 2 Crossbar 2 05 3 Rear sail attachment point 1 97 Crossbar Dimensions a Overall pin to pin length from leading edge attachment point to hinge bolt at glider centerline 117225 b Largest outside diameter 2 05 or 2 44 with optional shortpack airframe Keel dimensions least and greatest allowable distances whether variable through tuning or through in flight variable geometry from the line joining the leading edge nose bolts to a he xbar center ball center 48 75 25 b The pilot hang loop 066 75 1 5 Sail Dimensions a Chord lengths at 1 3 ft outboard of centerline OZ 2 3 ft inboard of tip 47 b Span extreme tip to tip 392 Location of Information Placard Kee Location of Test Fly Sticker Kee Recommended Pilot Weight Range 175 275 Recommended Pilot Proficiency USHGA Novice HGMA COMPLIANCE VERIFICATION SPECIFICATION SHEET GLIDER MODEL Falcon Y 145 MANUFACTURED BY Wills Wing Inc All dimensions in inches weights in pounds NOTE These specifications are intended only as a guideline for determining whether a given glider is a certified model and whether it is in the certified configuration Be aware however that no set of specifications however detailed can guarantee the ability to determine whether a glider is the same model or is in the same configuration as was certified or has those performance s
12. Installation The removal of the round control bar and installation of the Litestream bar can be done with the glider folded up and in the bag although the glider should be fully set up and a pre flight inspection performed after the installation Removing the round control bar 1 Unzip the glider bag Set the basetube aside 2 Remove the bolts and nuts that secure the basetube brackets and bottom side wires to the control bar downtubes Set the brackets bolts and nuts aside 3 Remove the safety rings and clevis pins that secure the bottom front and rear wires in the down tubes and remove the wires from the downtubes Set the pins and safety rings aside 4 Remove the bolts and nuts that secure the downtube top end plugs to the elbows Set the down tubes and the nuts and bolts aside 5 The parts you have set aside will not be used in the installation of the Litestream bar but should be retained for re installation of the round control bar 49 Installing the Litestream control bar 1 Start by correctly identifying the left and right downtubes The squared off part of the downtube profile and the longer bottom wire slots go to the rear the clevis pins are installed with the heads on the outside and the rings on the inside and the chord of the profile is toed in relative to the axis of the Y4 inch bolts and ball lock pins in the top and bottom fittings 2 Install the Litestream downtubes onto the elbows at
13. It is true that because of wing twist the root section is at the highest angle of attack relative to the remote free stream airflow but other fac tors influence the stall propagation on the wing Specifically a flex wing hang glider usually stalls first somewhere outboard of the root on each wing approximately one fifth to one third of the way out from the root to the tip in the area where your tufts are located As the angle of attack 1s raised further the stall propagates both outward towards the tips and inward towards the root If you wish to observe the stall propagation across the whole wing on your glider you can cut some more tufts from knitting yarn about 3 4 long and tape these to the top surface of your sail across the rest of the span During normal flight the flow will be chordwise along the wing and the tufts will point towards the trailing edge When the wing stalls the tufts will reverse direction indicating the local flow towards the leading edge At the first onset of stall the tufts will indicate the impending separation by first wiggling and then deflecting spanwise before they fully reverse and point forward The first onset of stall occurs well before the familiar stall break in which the glider pitches uncontrollably nose down to recover from the stall By the time the stall break occurs all tufts but those farthest outboard and those farthest inboard will have indicated reversed flow T
14. Replace any component with indications of permanent deformation or other damage Every twelve months or every 300 flights 1 Have the sail completely removed from the frame and disassemble all frame components Inspect every part of the glider for any damage or wear Inspect the tubes for straightness and for signs of corrosion Anytime you have the sail off the frame inspect all of the batten pockets and batten pocket terminations 2 Replace bottom side wires and hang loops Special circumstances l Any time you suffer a crash or extremely hard landing you should have an annual inspection done on your glider to insure that you find all damaged parts If you bend a downtube carefully inspect all hardware at the top and bottom of the control bar for damage 2 If your glider is ever exposed to salt water you will need to have the glider completely disassem bled in accordance with the recommended annual inspection procedure All frame parts will need to be disassembled including the removal of all sleeves flushed liberally with fresh water dried completely and treated for corrosion inhibition with LPS 3 or other suitable agent 3 Cleaning Your Sail Keeping your sail clean will extend the life of the cloth however cleaning the sail too often or scrubbing the sail excessively will accelerate the breakdown of the stabiliz ing resin in the cloth and shorten the life of the sail When cleaning the entire sail you should
15. TG 007 08 ALS paeoqing 4eqX y uoopea z I r6 0 91 S 0 menu mee T662 S II Jeqy 96T p uoolej 1 Cp 146 Lam 21497 usibus IER SUN Jed noy Jeg Lou UO SE M R ix E ae ae 790 866 66 9 866 Y1 XV4 Hd e 69826 VI 39NVHO e JAY 390183019 004 Ag SMLVLS Q3S1A38 NM V G1 1N3W0900 OI JMadis Jeg 043u0 punoy uo2 J NOISIA38 AALL gd IIVL3O AJIHL V T 91v7 096NV 14315 Wd3HSVM NVddlSdIIlS 4V34 WOLLOd 14S 34IM GNNOY dOL 941 LV 90 1d 4V82 TIVWS Tove NV ONTY Al434VS EJE COS UCSA Lt36 5006t0cSH OV LI fOI c0 t dOr SE O0LI dOI ULEC IJOL U21501 UUCT 90V bo y LSSVN Loge 301 0 SS EE Sd X Sle IV LSATH SE WEE ET Y EZ9SYN I 1S 301 G S9CNV 9I S INNADO OSOT NOT 020 X 9I X GL NOIAN S3HSVM S2IS fOI WY4ULS dOL IV MOd14 dv AE 902 LYOHS NN YLND 1442 13I149V48 PLIT 30G ANVI41SdI1S 301S WOLLOS 334 1M S0I dOrv NOOW4 Ada dSV8 AV VIS L QUE NVOJAT1Od 19N135V8 dI49 LOVI VST j9uV ZW NY ONIS AL3JVS 002L d0 s 92 X v l INNOJIIS GrvT NOT r y 2vOlZSW v T LAN HONITO OvZT NOT z 318Y1 33S uv8g033dS lv 38nl 3SW8 uuet 4ov I gg Gg ve ES oC m 0c 61 81 L1 9I cal Vi el et TRI see NI N CO Fee MP GALE WS fee aa E md Lv90 866 65 9 866 p1 XVJlHd e a98c6 VI 39NVHO e JAV 390183019 006 Ag SNLYLS 3511734 NMVSIO GI LN3AQOOQ UI JMQQ IS veg 1043009 seen Wei LINEA G SS NOI
16. VI JONVHO e JAY 3901H3018 OOS SNIVIS G4ASTASY MM d OT INIW UO 1 3MOdis NA SUTEAN NOISIA3W 31111 82000 ZT 8290061 00 6 O OoOo VER TE S IFI SE CT O 00 TZ 91 S 0 Uo X 91 S 0 Uo X 91 S 0 uUo 0 x CALS 3 JU044 O T eqni 31 deed OT CALS 9 ppHu 3 10044 O T UO2 Jj UO2 J UO0d Py 91 5707 91 8707 uug Q x uug 0 x e Lud Te 0 6I wu u15ue ALS 9 pptu 37 3u043 O T eqni 31 30044 O T 00 97 OWEN 3Jed u02 Py UO9 Py Ges e We SC BE voe qt 790 866 66 9 866 PLZ XVd Hd e G98c6 VI 3DNVHO e JAV 390183018 005 hg SNLVLS 03SIA38 NMC QI IN3W0900 QI AMANIIS d PON OLT Wgd P As SY EZ s ORIGER TULL Y Hue Jop Us MEN 0102 01 S Gz9 yjbua 1n9 A 9 S U11M JUaPLOULOD eqni 1u0Jj EN VIO c lt SL SE 0S8 Gi UG Oe nis ugipe t gt j j pn3s udeg E NJU oe VEA 9 I yoo uo33ng K UO u0110q GI o SS 6c8l 00 24 Je9 995 OLT YOSLEY ALS Uedu 99y E u0OO PJ el G0 00 eI 8II 29 v AIS jJu04J 995 UOS B 1 9T 918 07 men 7091 cT go 1U044 O T VOD CALS DDIU 993 UO32 63 NOSUV Id ap Love t Tt 2002 0671 MET QUEJA EV OLT t UO9I 31 600 366 6G 9 866 vL XVJlHd e 39826 VI JONVEO e JAY 39Q1H3018 DOS Ag SNIVIS 3STA38 MM d OT INIW UO 1 3MOdis q Jeqx O T uoote3 o U 65s Lp NOTSIASY a Ell
17. angle at which your harness suspends your body in your glider has a great deal to do with your perception of the bar position relative to your body Airspeed indicators vary in their indicated airspeed depending on the make of the instrument its calibration any installation error etc The use of tufts gives you an absolute first hand indication of the actual aerodynamic event associated with two critically important airspeeds on your glider It is a potentially useful tool that may improve your flying BE Speeds To Fly And Using Your Airspeed Indicator The optional Wills Wing Hall Airspeed Indicator has been specially designed to help you fly your Falcon at the proper speeds for optimum safety and performance Note The Wills Wing Hall ASI is color coded for VNE and Va speeds of 53 mph and 46 mph respec tively and the description below of the color coding on the ASI references those speeds The Falcon 3 and Falcon 4 170 and 195 have lower VNE and Va speeds of 48 mph and 42 mph You can still use the airspeed indicator to determine proper speeds to fly but the top or the green region the yellow region and the red line are not correctly located for the Falcon 3 and Falcon 4 There are four color coded bands on the ASI White This is the range from 20 mph to 30 mph This is the normal flying speed range While thermalling or flying in lift try to keep your speed within the lower half of this range For gliding in light sink o
18. compromise the flight characteristics of the glider The effects of too tight bridles are to increase roll control pressures and reduce roll rate in circumstances where maximum control input 1s applied Other factors of glider geometry which affect bridle adjustment and effectiveness The effective adjustment of the bridles is also affected by other aspects of the glider geometry For example if the bottom side wires are too long 1t will allow the wings to rise and slacken the bridles in normal flight If they are too short it will pull the wings down and tighten the bridles in normal flight If the top side wires are too short it will reduce the amount the wings can fold downwards as the glider unloads at low angles of attack thereby reducing the effectiveness of the bridles Changes from proper length to the top or bottom side wires will also change the relative adjustment of the inner and outer bridles to each other and change the way they operate Finally normal shrinkage of the sail over time by reducing the spanwise distance to the bridle attach ment station will loosen the bridle adjustment and this should be corrected Please see the Technical Bulletin on Reflex Bridle Adjustment And Maintenance available in the Support section of the Wills Wing web site at www willswing com for more information on maintaining and adjusting bridles Maintenance Schedule You should continually maintain your glider in a pr
19. edge outboard crossbar assemblies Swing the outboard crossbars towards the nose again Re stow the clevis pins and safeties in the front leading edges Remove the safety ring and clevis pin securing the rear keel to the front keel and remove the rear keel Re stow the clevis pin and safety ring in the front keel Unzip the short pack bag and fold the corners of the bag down around the outside of the corners of the box a Bu O Lay the front leading edges front keel assembly and the inboard crossbars assembly in the box At each stage of the packing process use the glider s cover pads cover bags and any additional materials necessary to pad hardware fittings and protect the tubes from damage or abrasion Lay one end of the open glider bag flat over the first layer of tubes Lay the mid leading edge out board crossbar assemblies and the rear keel in the box on top of the glider bag Fold another layer of the glider bag over this layer of tubes Remove the basetube from the con trol bar Lay the remaining tubes in the short pack box Remove the longest battens 5 s on the Falcon 3 145 5 s and 6 s on the Falcon 3 170 or 195 from the batten bag break them down to their short pack length by unscrewing the rear portion at the threaded coupling and return them to the batten bag 44 8 Fold the sail as follows a First fold the sail along the glider center line laying the mylar pockets flat one
20. guideline for determining whether a given glider is a certified model and whether it is in the certified configuration Be aware however that no set of specifications however detailed can guarantee the ability to determine whether a glider is the same model or is in the same configuration as was certified or has those performance stability and structural characteristics required by the certification standards An owner s manual is required to be delivered with each HGMA certified glider and it is required that it contain additional airworthiness informa LION Weight of glider with all essential parts and without coverbags and nonessential parts 45 Ibs Leading Edge Dimensions a Nose plate anchor hole to 1 Crossbar attachment hole 10255 2 Rear sail attachment point 195 5 196 25 b Outside diameter at 1 Nose 2 05 2 Crossbar 2 05 C Rear sail attachment point 1 9 7 Crossbar Dimensions a Overall pin to pin length from leading edge attachment point to hinge bolt at glider centerline 96 37 b Largest outside diameter 2 05 Keel dimensions least and greatest allowable distances whether variable through tuning or through in flight variable geometry from the line joining the leading edge nose bolts to a he xbar center load bearing pin 42 75 25 b The pilot hang loop 59 5 1 5 sail Dimensions a Chord lengths at 1 3 ft outboard of centerline 77 6 2 3 ft inboard of tip 46 0 D Span extreme tip to tip Con Loc
21. of the manual covers the 2 3 length breakdown and reassembly procedure Note that the procedure for the Falcon 3 Tandem is slightly different due to differences in the leading edge construction The different proce dures for the Falcon 3 Tandem are specified in each section of the instructions To break down the leading edges follow these steps l Lay the glider on the ground or floor unzip and remove the bag and remove the velcro ties Undo the velcros that hold the sail around the aft end of the rear leading edge at the rear sail mount and pull the sail rearward at each tip to dismount the sail from the rear leading edge You may use a large flat bladed screw driver to pry the sail mount webbing away from the slotted endcap Take care that the screwdriver does not have a sharp edge which might cut or damage the webbing Obtain an indelible marker Check to see if the rear leading edges are labeled left and right If they are not mark the rear leading edges left and right remember that left and right are reversed if the glider 1s lying on its back upside down On the Falcon 3 and Falcon 4 145 170 or 195 the junction of the rear leading edge and front leading edge is aft of the leading edge crossbar junction The forward edge of the rear leading edge is slotted and this slot engages on a clevis pin in the rear portion of the oversleeve on the front leading edge Pull the rear leading edge straight aft to disengag
22. on top of the other b Then fold the body of the sail in segments over onto the mylar pockets so that the result ing width of the folded sail equals the width of the short pack box c Finally fold the sail in lengthwise segments equal to the length of the short pack box and lay the sail in the top of the box 9 Add any left over soft items on top of the sail hang loops any remaining cover bags velcro ties etc Fold the protective bag back over the corners of the box and zip up the bag Cinch the velcros on the bag to square up the box and compress the package to its minimum size Re Assembling the Glider From the Short Pack Configuration l Prepare a clean non abrasive work area or lay down a clean protective tarp to work on 2 Unzip the short pack bag and remove all of the contents 3 Assemble the mid leading edge crossbar assemblies to the front leading edges noting the left right alignment stickers or marks that you made At the leading edge crossbar junctions swivel the top and bottom side wires tangs so that they point towards the nose of the glider 4 Swing the outboard crossbars towards the rear of the glider and install the neoprene keel protec tors over the ends of the tubes to protect the sail during insertion of the frame 5 Remove the washout tubes from the rear leading edges and install the rear leading edge tubes into the front leading edge tubes taking proper note of right and left and making sur
23. original strength Some degree of fatigue due to repeated bending of cables is almost unavoidable in an aircraft that is assembled and disassembled with every flight Bottom side wires are subject to the highest loads in flight and are therefore the most critical This is why we recommend that these wires be replaced annually even if there is no known damage The requirement for immediate replacement of a cable known to have been bent or otherwise damaged supercedes this annual replacement requirement Replacement cables should always be obtained from the factory or if not from the factory from a reliable source known to use proper fabrication procedures An improperly made cable may appear perfectly OK on visual inspection but could fail in flight at a load much below the intended design strength of the cable Even if the replacement cable is obtained from the factory it should be checked carefully for length against the cable it is replacing and inspected carefully before being installed Removing The Sail From The Airframe And Short Packing The Glider Many maintenance and repair procedures will require the removal of the sail from the frame In ad dition the first step in short packing the glider to its shortest breakdown length is the removal of the sail Please follow these instructions when removing the sail short packing the glider and reinstalling the sail Please read all the instructions for each operation bef
24. pilot s center of mass forward ahead of his shoulders effec tively shortening the pilot s arms and reducing flare authority The proper position is with the pilot s body inclined forward with the shoulders out ahead of the pilot s center of mass Thinking about pushing up instead of out when flaring may help you to maintain the proper forward inclined body position 9 Falcon Breakdown Breakdown of the glider is the reverse of assembly Unlike gliders with tighter sails the battens on the Falcon can be removed with the crossbar ten sioned Always remove the battens gently so as to avoid undue wear on the batten pockets or stress on the battens which may change their shape l Set the glider at slightly more than 90 degrees to the wind direction slightly tail wind Detach the nose cone from the bottom surface of the sail Dismount the nose batten and pull it out about 2 past the noseplate Remove the 1 battens and 2 shortest cambered battens dismount the wash out tips roll the sail under at the tips and install the tip cover bags over the sail and washout tips Depress the keyhole button lock on the bottom of the noseplate to allow the keyhole tang to be disengaged Disengage the tang by pulling down on the nose of the glider while pushing up with your thumbs on the plastic tang handle Depress the keyhole button lock on the rear of the keel and disengage the top rear wire Pull back on th
25. procedures Pilots wishing to tow should be USHGA skill rated for towing and should avail themselves of all available information on the most current proper and safe towing procedures Sug gested sources for towing information include the United States Hang Gliding Association and the manufacturer of the towing winch or equipment being used Wills Wing makes no warranty of the suit ability of the glider for towing Flight operation of the Falcon should be limited to non aerobatic maneuvers those in which the pitch angle will not exceed 30 degrees nose up or nose down from the horizon and the bank angle will not exceed 60 degrees The Falcon is generally resistant to spinning but will spin from a stalled turn at bank angles of 40 degrees or more or if the pilot applies positive pitch control aggressively in com bination with roll control input so as to roll towards the high wing Recovery from a spin requires un stalling of the wing and it is therefore important that in the event of a spin no application of nose up pitch control be held The Falcon will recover from a spin once control pressures are relaxed As the nose lowers and the angle of attack 1s reduced the stall will be broken and the spin will stop How ever such recovery will consume significant altitude and will result in the glider assuming an unpre dictable heading Recovery from a spin may therefore involve a flight trajectory which intersects the terrain at a high rate of spe
26. the cut edge of the tube and the midpoint of the threaded insert in the rear tube about 7 8 inch from the cut edge of the tube Use a sharp punch to dimple the tubes and secure the coupling Check the punch indendation at the front batten tip and rear lever assembly as a reference for the punch depth required to secure the coupling Unscrew the coupling to beak down the batten The figures below illustrate positioning the coupling at the tube Junction and the punch locations Bag Box assembly The bag assembly includes the following items Heavy duty ballistic cloth zippered bag Corrugated plastiboard liner box Wheel assembly with fasteners The plastiboard is scored and folded in 2 places so it can be shipped without oversize charges When assembled into the box configuration it fits snugly inside the ballistic cloth bag and provides protec tion for the airframe on 5 sides The sail is packed on top of the airframe and protects the airframe on the remaining top side Please note if you choose to install the wheel assembly and you wish to subsequently fold the box and bag flat you ll need to remove at least one set of the fasteners on the bottom of the wheel bracket Use the following proceedure to install the wheels Position the plastiboard box evenly inside the bag The plastiboard has punched holes coresponding to the fasteners that mount the wheel assembly Use an awl to punch corresponding holes through the bag The wheel
27. the glider while pulling on the bottom front wires to raise the glider up onto the control bar Secure the bottom front wires as described above gt n Falcon 3 view Launching And Flying The Falcon 1 Ifthe wind is more than 10 mph or gusty you should have an assistant on your nose wires on launch and if necessary an assistant on one or both side wires Make sure all signals are clearly understood Do a hang check immediately prior to launch The angle at which you hold the glider should depend on the wind speed and slope of the terrain at launch you want to achieve a slight positive angle of attack at the start of your run 2 Run aggressively on launch and ease the bar out for lift off 3 The flying characteristics of the Falcon are typical of a medium performance flex wing Make your first flights from a familiar site in mellow conditions to give you time to become accustomed to the glider 4 We recommend that you hang as close as possible to the basetube in the glider this will give you lighter control pressures and better control Using Wing Tufts Your Wills Wing glider has been equipped from the factory with short yarn tufts on the top surface of each wing The shadow of these tufts will be visible through the sail The tufts are useful for indicat ing the local reversal of the airflow which is associated with the onset of the stall in that portion of the wing You can use these tufts as described below to he
28. the placarded maximum rough air speed c 123 of the placarded speed never to exceed for at least three seconds without failure The required speed for this test was 59 m p h 2 Anegative 30 degree angle of attack load test at a speed equal to at least the greatest of a 100 of the placarded maximum maneuvering speed b 100 of the placarded maximum rough air speed c 87 of the placarded speed never to exceed for at least 3 seconds without failure The required speed for this test was 42 m p h 3 Anegative 150 degree angle of attack load test at a speed equal to at least the greater of 30 mph or 50 of the required positive load test speed for at least 3 seconds without failure The required speed for this test was 30 m p h 4 Pitch tests at speeds of 20 m p h 34 m p h and 48 m p h which show the glider to have a posi tive pitching moment coefficient over a range of angles of attack from trim angle to 20 degrees below zero lift angle at 20 m p h and from trim angle to 10 degrees below zero lift angle at 34 m p h and from 10 degrees above zero lift angle to zero lift angle at 48 m p h 5 Flight maneuvers which show the glider to be adequately stable and controllable throughout the normal range of operation The Falcon 3 s and Falcon 4 s have been designed for foot launched soaring flight They have not been designed to be motorized tethered or towed They can be towed successfully using proper towing
29. the safety rings and clevis pins that secure the control bar downtubes to the top plugs and set the control bar assembly aside Re install the clevis pins and safety rings in the control bar downtubes Remove the screws that secure the sail at the nose and replace the screws in the leading edges Remove the remainder of the velcro sail ties Spread the wings slightly undo the Velcro tabs inside the rear ends of the leading edges and then dismount the sail from the rear leading edges by pulling straight aft on the webbing handles A Pull straight aft on the rear leading edge tubes to remove the rear leading edges from the frame Note You can skip this step if you are not short packing the glider ue Prop the nose of the glider up on the breakdown storage transport box and spread the wings slightly Pull the crossbar sweep wire and attached top rear wire forward out through the keel pocket If there are no alignment stickers installed at the joint between the inboard and outboard crossbars use an indelible marker to mark a line across the splice on each crossbar and indicate L or R left or right on each of the four tubes at this junction Remove the mid crossbar safety rings and clevis pins nn E E Pull the crossbar center towards the nose of the glider working it up and down as necessary to disengage the inboard crossbars from the outboard crossbars Re stow the clevis pins and safety rings in the inboard crossb
30. 0 9 ALS JBaJ aay uooej I CG 91 9 0 soe 00 21 ZALS IDpiu eoy uoolej Fi qD AW DE uu pen ups BUEN Jed 1911 H ES Wee ES Wu EE E E rd 11v90 866 69 9 866 p1 XVJlHd e 9876 VI 39NVHO e JAV 390143019 00S Ag SQ VIS Q3SIA38 NMV SO OI LN3AQ200 OT 3M00 IS gr et geet ENEAS SNE NOISIA38 3 1111 La 0S I S LII 08 8 97 GG ev pueoging JeqX S6T uoo ej ES 00 ALS JeqX S6T Uoolea z 05 28 pueoquy Jeqx G6T uoole4 T y1bua7 OWEN 1Jed EI Inn 91 G 0 Uug Q x uuog um 9 gent 1 900 aam uu6 0 x me uu 2 97 1 zz 91 S 0 w6 0 x men mees 9 ER 009 SITONV ds 00Z 8L 10 Aa XXXX NMVUG XXX XX X SNL 6Z0S 6 0900 6l ap daan Inouse M Pn4S ON 00 L ds 4002 81 10 3A08ddV VN MQNO21Vd d 0 1N3Hf200 Gids uapue c uo3 eJ SZ bp3 buipea Je9y GZL 6 VN 790 866 65 9 ON 1uVd 866 5141 XV4 Hd S99Z6 VI JONVYO JAY 3501343018 005 m JNE 83 TUES SJ343u saunu Jem x JaJaweig ads jewaye uoljdi3saq Ql Gan 009 uu6so0xzsz 9 S O Ss lue s A 8 8 S Je J al 9 Un Jong uu60x0s2 91 SLOE SSI WEIS 3133 5 JUOJJ oul ara osse uucoxesz s1 stor os era arz Fal mees mees ER Z 0009 uueoxooe 9 S401 Ssajueag 313319 JeqssoJ en SCT BET uueoxzoe 91 SLOE SSI WEIS 948UJ34 8 JeqssoJ GOL eze DE 8soxgz8 91 1909 ssajuweas puepu
31. 10 e uU0OLIALIIDSI J QunN 3Jed u 1 i RE AAA 4 J9DVS TE TW NT D e AVION Y dl 89 00 Dec AVION Y 3903 9NQ1 WWeS 1440Vdd 31 84V4X 99 499 uec Ge aum GE W 790 866 66 9 866 p XV4IHd e 898c6 VI 39NVHO e JAY 390183019 006 SMLVLS ELE NMVeQ QI IN3W0900 G1 3MQQ1S aay Jeey uoo eq g LAR EATA SCHER NOS4Vd Ag Lef C 90dVVHO 0627 X 9T TV LAAIY 1901 AQVATAVH ONTYdS NOLLNG ONIGd4M 8 8 LOIS 2 310H T ONVL het qV3d ASSV LAN 3491102 310HA3A 906 90 EN EA ES Lot vee EAT REN 3 BER EA ER ER p9IEQ YOL TIST AE A 2 OMS TIVE YVIY dOL JYIM TOPZ d0Y LaS 39NIH WSIJNO d44dMS Ava 31M VOcv dOv cOtt dOv ONVL 4V34 WOLLOd LAS FAIM d1s11 415415 ave Wie Las aim GU E dl ALO W9Ppue ALO I L Bp 7 5 9 Jeo 02 P Gelee 800 1 s 00c cc 6 EE e dis 1190 866 6689 9866 F XV4 Hd e 49826 VI 39NVHO e JAV 390183019 00S Sn1VIS ISTAJN NMVG G1 IN3N0200 OT 4maqis abp3 Butpe 1 ueay uoo e4 Lol LA Ss lle NOISIA38 abb Y9ENY 91 OUudMO1 1nN3201 OSTI NOI 3 92 028 SW 91 NVd M3WNOS T9OT 101 w uny 1V 919e7dad3y 3qn anouseM IIv2 502 520 X 820 X OSZ 1V N32VdS 80TI LOT TIVWS I6F6 NV ONIY AL3JVS O011 dOI ws MA 12324268029 OSO T J NVIILINW v dvo N3 8090 851 NIVI3N 339N
32. 1t may not be apparent that the front wires have become disconnected or are in danger of being disconnected from the nose Please note that the nose line must not be routed in any way such that it can pull forward on the nose wires or the nose tang The incorrect routing shown is one example of a way in which this could happen It could also happen however if the nose line is routed out side the V of the wires but behind the tang handle Please note that the button safety lock may not be effective in preventing the nose wires from being disconnected by an improperly routed nose line Make sure that the nose cone is not installed in such a way as to depress the button lock All pilots planning to platform tow using a Wills Wing glider fitted with the keyhole tang nose catch must as their last checklist item prior to going to cruise positively verify that the nose line is not routed in such a way that there is any possibility that it can cause the nose wires to disconnect A Few Notes About The Falcon 3 Tandem Federal Aviation Regulation FAR Part 103 Ultralight Vehicles which governs the flight operation of hang gliders in the United States restricts the operation of any ultralight vehicle to a single occu pant The United States Hang Gliding and Paragliding Association has obtained an exemption to the single occupant requirement of FAR Part 103 which allows for two place or tandem flying in a hang glider Pilots op
33. E 26 Speeds To Fly And Using Your Airspeed ndcator esee 28 Landing The Falcon 29 Falcon STE ele uuu uu uuu uu uqu a EEEE EAEI EREE IE DI isso 33 Falcon Stability Systems diana 34 Maintenance Schedule ccccecececeeeeeeeueeeueeseseeeeeeseaeanausesesenstataearauausesenenanaeas 36 Removing The Sail From The Airframe And Short Packing The Glider 37 Falcon Shortpack Bag BOX E 38 Installing The Optional Litestream Control Bar Kit 49 nn A O PO EEEE 51 Car Top Mounting And Transport serias is 53 a GOS S yg SSS SS S n 53 HGMA Compliance Verification eese 54 60 ms amica TT TT e e O E 61 78 Assembly Diagrams nenne nennen nennen rain seen nnns 80 89 Introduction Thank you for purchasing a Wills Wing glider and welcome to the world wide family of Wills Wing pilots We are a company of pilots and aviation enthusiasts and our goal 1s to serve your flying needs now and in the future as we have done for pilots throughout the world since 1973 We encourage you to read this manual thoroughly for information on the proper use and maintenance of your Wills Wing glider If at any time you have questions about your glider or about any aspect of hang gliding that your Wills Wing dealer cannot answer please feel free to give us a call Please visit our web site at http www willswing com on a regular basis The site features extensive information about Wi
34. ISIA38 ele NS VAG ve ce e OMS TIYE LNOUYS 8 1 OMS LI JUIS KR OMS Tiyu 30 09 WIGNVL S224 MIS M WYLS JA ON 31 WULS J41M 8 T 183SNI dOl WNIY IV LYdSNI dOl da VIA 10d SOON TA da VIA lOd dOL 1SOdINIA S A pI MEM GEN KLO Wepue Te ALO E UO9LPy UI LNAWN900 A quassy 1SOGBULY UOD e4 aa Qv3H HOVW WS T3 ce79 JLTHM 3SV8 dA OJILSVI4 JIVLOId 3101489 ISOdINTA 1S0d9NI LSOdONTA 1S0d9NI WW L3AIS M449S uor3diJosoaq 280 SV LOlv dOv LOv dOv Oc ge 0cc d0Yv 0cc d07 CoLL AOV TELT 107 Assy 3sodBuLy uoo e4 Vi el el E 0T NE S WS BER Nm I LE W3ll 01 200 AALL LV90 866 69 9 866 Y1 XV4 Hd e S98Z6 V9 J9NYY0 e JAV 390143019 00S BAINES UTA L Medien M PUE ES SE l A E 2 id Lv90 866 65 9 866 v1 XVJlHd e 9876 VI 3DNVHO e JAV 390143019 006 A8 S IV 1S 351134 NMV30 OUT 1N3WNIO0 dI AMGUGIS EN SI NOISIA38 Se UA NA Jay DR v 90dVVHD GLE X 9T IV LAATY 9960 dor AR De Lien OVZT NOL ve gI GT Vi el el LI OI deoiny pepeaJu O GXOoXUV L SS dd 3k 400905 MAGS WE NE GE L Lou P QVOl2SW but Im HINITO EECHER I YLce YNV Lice NOI CIUC dsl Ole IJa ULLL I0S 8 L OMS 114 301S dOl 339 1M See cele OMS T1IV8 3015 dOl JAIM Dev dl JIALS LV 8 T 3015 WOLLOS 34 1M YOILE dOY JIALS LV Z AGIS WOLLOd 384 1M COTE dOv Wopue AL0 861 ADS DOT AL0 SvT
35. R rS I 91 S 0 v8 1 Ge UL eqni 31 14044 SYT UOd e4 10 1UbL9M EENS wu u15ue y1bu37 OWEN 2484 SCHER dp NOISIA38 yoo 40318 VI0c 9c c L002 0 T 9UEJJJLV GYT UO9 B EE 03SIA38 Wu 01 1N3n200 QI Magis 3 ILLE 00 6v EM Q M B BIB B HHRET ZS naui 82h pnis usa pa Kiuo uo330q ei 1 o 9 5 0 omg 00 21 ZALS eippur Lg 1 et 9138 7 GIST 968 quoud 139 ST Ki aom Le LuaTeW uu y16ua7 y16u97 OWEN 1184 uo2 eJ uo2 eJ uo2 eJ uo2 0j UO9 Py 1790 866 69 9 866 11 XV4 Hd e 59876 VI 39NVHO e JAY 390143019 00S ae opt uoote3 G Al Ae QuB UA LA L uod e NOSUVd vIOZ 91 2 L002 0 1 HV SYL VOSLEA 500 866 6GE9 866 LL XVJlHd e 39826 VI JONVEO e JAY 3901H3018 OOS Ag SALVLS 3SIA3N MM ad OT 1N3NNIOO 1 3MOais g 4eqx Spt wooed o EA 6s UA NOISIA38 SREL SL 0S l 494790 ge V9 sdno jeq une ULM A S Q z X une A S PUROGUT Jeqx Spt UOD e4 pueoging 4eqy SYT uoo ej ALS JeqX GYT U00 4 pJeoqu JeqX GL UOILe4 OWEN 3Jed J boo 941 9404 w6 x uzg I 0072 6L0 91 9404 wu6 0 x wos e 0 9 v00 oan w6 o x meg tg lm ei ao un6 0 mee vest Sz 69 op abia DIE uu yy6uay uq6u 1 NOSUWad 02 1 11 2002 08 7 VN QUEJA EV OLT VO9LEA gt 000 366 5689 9866 b1 XVJlHd e 39826
36. SIA38 AALL WVi4 IS dOl IV MOd14 dv SE Ee Ve LYOHS NNVV YLND 1344 1343Vdg L01502 EU Wwv34lSdlIlS 1NO0344 NOLLOS 13S d8IM cOce dOv NV3YISAIIS Vun WOLLOG 13S 3HIM 20 d0v WV3HISdI1S 301S WOLLOG 38IM SOI dOP GET 25 0 14 SLAVE 0 M 29 931 MV3YISILIT Z vl 90 S613 SI398 O M S9 931 WV3YLSILIT vLvl 90v 0 13 SLAVE ON WALSdIS Wi 38n13SV8 1291 309 G6T4 Sang ON WYLSdIS WNTW 38n13SV8 TISI 40f 1UBLY 39xy25eJg eqnaeseg ueoJ3s9111 vvel 902 1197 3853506439 aqniaseg uP23J359113j h81 902 up 9 u0110g 59 wes4759117 Bid 82 68 1 902 1481 uo330g a1 uesj3s91 1 Nld 82 89 I 902 4464 dol Be ease Nld 82 ton 1481 dol Bei wea1159717 Nld 89 S 91 902 020 X 91 X SL NOTAN W3HSVM G2TS NOT LBT X 02 X 099 AN W39VdS EOTS LOT 058 X 820 X SITE SS HSNd O2lv 10l S2l X 820 X 21 SS Heng bTIb LOT 0v2 X 820 X 21 SS HSh8 II 101 044 X 820 X OSZ TW N32vdS EOTT LOT TIYWS 1676 NV 9NIN Al3iVS OOTI d0T OT Y ZYOIZSW kt LNN HONITO OPZT NOT 2v1029W 91 LNN HONITO O ZT NOT G S9ENY 91 8 10NX201 O OT NOT du WHEE X HI X901 TiV8 NId EETE MOT D SS v9 0d22 SZ X 91 TW 13AIN E9E0 801 DOGG Le De 6c 8d Lc 96 D ve Le 0c 61 8I LI 91 SI Vi er Im BE B 6t d V SE SZ O E 800 T S G00 81 7 135138 NMY d NOS4Vd Ag SMLWLS NO
37. are intended only as a guideline for determining whether a given glider is a certified model and whether it is in the certified configuration Be aware however that no set of specifications however detailed can guarantee the ability to determine whether a glider is the same model or is in the same configuration as was certified or has those performance stability and structural characteristics required by the certification standards An owner s manual is required to be delivered with each HGMA certified glider and it is required that it contain additional airworthiness informa tion 1 Weight of glider with all essential parts and without coverbags and nonessential parts 48 Ibs 2 Leading Edge Dimensions a Nose plate anchor hole to 1 Crossbar attachment hole LE S 2 Rear sail attachment point 209 25 210 b Outside diameter at 1 Nose 2 05 2 Crossbar 2 5 3 Rear sail attachment point 1 9 7 3 Crossbar Dimensions a Overall pin to pin length from leading edge attachment point to hinge bolt at glider centerline 105 b Largest outside diameter 2 05 4 Keel dimensions least and greatest allowable distances whether variable through tuning or through in flight variable geometry from the line joining the leading edge nose bolts to a The xbar center ball center 46 25 25 b The pilot hang loop 063 1 5 5 Sail Dimensions a Chord lengths at 1 3 ft outboard of centerline 85 2 3 ft inboard of tip 47 b Span extreme tip
38. ars When the inboard crossbars are disengaged from the outboard crossbars turn the inboard crossbar assembly on its side and bring it around one side of the keel P SN Feed the top side wires into the sail through the holes in the top surface Swing the outboard crossbars to the rear to align them with the leading edges Carefully slide the frame out through the nose of the glider If you encounter resistance stop and find out what is hanging up If you need to send the sail into the factory for repair first remove the bridle cables then fold and package the sail carefully To detach the bridle cables from the sail push on the end of each cable loop at the bridle ball to make the cable loop round and allow it to be worked free of the notch in the bridle ball Remove the ball from the cable and remove the bridle cable from the grommet in the sail When you send in the sail be sure to include written instructions of what you want done your name and a phone number where you can be reached during the day CS Completing The Short Packing Of The Glider E If there are no alignment stickers installed at the joint between the front and mid leading edges use an indelible marker to mark a line across the splice on each leading edge and indicate L or R left or right on each of the four tubes at this junction Remove the safety rings and clevis pins securing the mid leading edges to the front leading edges and remove the mid leading
39. as possible and does not depress the button lock safety feature securing the bottom front wires Note If you hear a flapping sound after launch it may be that you have forgotten to secure the nosecone If this happens don t panic fly the glider at moderate speed to a safe landing E Ed 16 Conduct a complete preflight of the glider according to the following procedure checking all assemblies which have not already been checked Every bolt nut pin safety ring and fastener of any kind should be checked during every pre flight A full pre flight inspection should precede every flight you make not just the first flight of the day Along the left leading edge Check that the mylar insert is lying flat in the mylar pocket and that it is not severely creased or buckled A sharp crease in the mylar insert could cause a premature stall or stall hysteresis delayed stall recovery that can adversely affect both handling and performance Check the nut which secures the leading edge crossbar bracket to the leading edge and check the nut and safety ring which secures the crossbar to the bracket Check that the sail is not caught on the crossbar end nor on the safety ring nor on any of the hardware Check that there are no cocked thimbles on either end of either bottom side wire or on the crossbar end of the top side wire d While pushing up on the leading edge between the nose and the crossbar Junction step on the bo
40. at the tip We have found that if the plug on 1 battens are adjusted too tight it can increase the chance that the glider will enter a mild spin when stalled in a turn If you experience this tendency try loosening the number one battens slightly _ y Leading edge sail tension The tension in the leading edge of the sail adjustable by shimming as described above will influ ence the performance and handling of the glider If the sail is mounted too loose the performance will deteriorate noticeably If the sail is mounted too tight the glider will handle poorly it will be stiff and slow In roll response with excessive adverse yaw and an increased tendency to spin in a stalled turn As the glider gets older and the sail stretches you may need to add shims to maintain the proper ten sion Please note that adding shims may reduce the speed at which trailing edge sail flutter begins Car Top Mounting And Transport Improper or careless transport of your glider can cause significant damage You should transport your glider on a rack which has at least three support points which span at least 13 of the length of the glider These should be well padded and at least four inches wide to distribute the load Your glider should be mounted on your rack with the control bar facing up It should be securely tied down with webbing straps which are at least 1 2 wide If you drive on rough roads where the glider receives impact loads you should
41. ation of Information Placard Kee Location of Test Fly Sticker Kee Recommended Pilot Weight Range 120 190 Recommended Pilot Proficiency USHGA Novice HGMA COMPLIANCE VERIFICATION SPECIFICATION SHEET GLIDER MODEL Falcon 4 170 MANUFACTURED BY Wills Wing Inc All dimensions in inches weights in pounds NOTE These specifications are intended only as a guideline for determining whether a given glider is a certified model and whether it is in the certified configuration Be aware however that no set of specifications however detailed can guarantee the ability to determine whether a glider is the same model or is in the same configuration as was certified or has those performance stability and structural characteristics required by the certification standards An owner s manual is required to be delivered with each HGMA certified glider and it is required that it contain additional airworthiness informa tion 1 Weight of glider with all essential parts and without coverbags and nonessential parts 48 Ibs 2 Leading Edge Dimensions a Nose plate anchor hole to l Crossbar attachment hole 1419 5 2 Rear sail attachment point 209 25 210 b Outside diameter at 1 Nose 2 05 2 Crossbar Van tle 3 Rear sail attachment point 1 97 3 Crossbar Dimensions a Overall pin to pin length from leading edge attachment point to hinge bolt at glider centerline 105 b Largest outside diameter 2 05 4 Keel dimensions least and greatest allowa
42. becomes difficult to install or remove If your glider is equipped with a Litestream control bar attach the basetube to the downtubes by aligning the downtube bottom end plug fittings into the gap in the basetube end brackets and installing the ball lock pins Make sure that the ball lock pins are inserted fully into the basetube bracket otherwise they may not be secure s Flip the glider upright and set it on the control bar and remove the glider bag and all Velcro sail ties Spread the wings almost all the way Raise the kingpost to a vertical position checking to make sure that the top front and top side wires are not wrapped around the kingpost Attach the bridle ring to the snap hook at this time taking care that there is not a twist or rotation in the bridle ring which causes the bridle lines to cross over one another Lay out the battens and check each batten for symmetry against the corresponding batten from the other wing Wills Wing convention 1s that black tipped battens go in the right wing and white tipped battens in the left except for the straight 1 plug on battens which may both have the same color tips Install the 2 longest cambered top surface battens in the sail Do not engage the lever tips in the trailing edge at this time Order of batten insertion is longest to shortest from the root out Spread the wings all the way and check all cables for any twisted thimbles or tangled cables At the rear of the
43. ble distances whether variable through tuning or through in flight variable geometry from the line joining the leading edge nose bolts to a The xbar center ball center 46 25 25 b The pilot hang loop 063 1 5 5 Sail Dimensions a Chord lengths at 1 3 ft outboard of centerline 85 2 3 TE inboard of tip 47 b Span extreme tip to tip 550 5 6 Location of Information Placard Kee Location of Test Fly Sticker Kee 7 Recommended Pilot Weight Range 140 220 8 Recommended Pilot Proficiency USHGA Novice E HGMA COMPLIANCE VERIFICATION SPECIFICATION SHEET GLIDER MODEL Falcon 4 195 MANUFACTURED BY Wills Wing Inc All dimensions in inches weights in pounds NOTE These specifications are intended only as a guideline for determining whether a given glider is a certified model and whether it is in the certified configuration Be aware however that no set of specifications however detailed can guarantee the ability to determine whether a glider is the same model or is in the same configuration as was certified or has those performance stability and structural characteristics required by the certification standards An owner s manual is required to be delivered with each HGMA certified glider and it is required that it contain additional airworthiness informa tion Weight of glider with all essential parts and without coverbags and nonessential parts 53 Ibs Leading Edge Dimensions a Nose plate anchor hole to l
44. carefully to make sure that it is not deformed at the split in the ring in such a way that it could catch on the sail Replace it with a new one if it is deformed It is also very important that the bolt is installed in the proper direction If the bolt 1s installed upside down it greatly increases the chances of the safety ring being caught by the sail and pulled out Whichever type of nut is being used do not overtighten the nut dur ing assembly the nut should be snug but the top and bottom side wire tangs should be able to swivel on the bolt without requiring undue force As you complete the assembly make sure that the top and bottom side wires are properly routed 5 Remount the sail to the rear leading edge making sure to align the inner sail mount webbing NOT the outer webbing handle squarely in the slot and attach the securing velcros Make sure the sail 1s properly oriented the velcros should be on the inside of the leading edges You may find it helpful to use a large flat bladed screw driver to pry the sail mount webbing over the end of the leading edge tube and into the slot Take care not to damage the webbing Alternately first remove the sail mount screws located at the front of each leading edge to release the tension The sail mount screws may be difficult to replace until after the glider is completely assembled Spread the wings carefully and incrementally while pulling the sail forward at the nose during assembl
45. ch the basetube fold the control bar and install the control bar bag and keel protective cov ers Note The glider will fit in the bag more easily if you remove the basetube at both ends 12 Gather the battens so that all the cambered ends match up put the battens in the batten bag tail end first and cinch the velcro tie on the bag This will make it less likely for the battens to get out of shape Place the bag in the rear of the glider between the rear leading edges and zip up the bag Falcon Stability Systems Stability in pitch 1s provided by reflex in the root section which is determined by the lengths of the kingpost control bar and front to rear top and bottom wires and by the shape of the root battens and by reflex support bridles running from the kingpost to the trailing edge at the number five and six and seven on the Falcon 3 Tandem battens and by washout tips installed in the leading edge supporting a transverse batten between the number two and three batten Correct attachment and proper adjustment of the bridles are critical to providing adequate stability at low angles of attack particularly those below the normal operating range Reflex bridle adjustment The bridles are checked by measuring the supported height of the sail above the keel The glider must be fully assembled as if it were to be flown in order to measure the bridles The glider must be out of any wind that might put pressure on the sail Place a small
46. change to the clinch nut and nylon nut cap is intended to address a number of problems with each of these configurations When installing the clinch nut on the bolt it should be tightened down until all slack is taken up and then backed off just enough to all the secured parts to swivel under light to moderate pres sure The nylon nut cap is then installed onto the bolt as far as it will go do not over tighten or you will strip the nylon threads The following bolt changes are required to provide sufficient threads to engage the nut cap Falcon 3 4 145 170 195 No changes required may change to A type no hole Falcon 3 Tandem AN4 32 changed to AN4 33 or 33A Sport 2 62mm Xbar side wire AN4 32 changed to AN4 33 or 33A Sport 2 175 66mm xbar Xbar side wire ANA 33 changed to AN4 34 or 34A U2 Xbar side wire AN4 30 changed to AN4 31 or 31A Sport 2 Xbar Leading Edge AN24 46 changed to AN4 27 or 27A U2 Xbar Leading Edge No changes required may change to A type no hole Falcon Breakdown Procedure For Shipping And Reassembly Procedure The Falcon 3 and Falcon 4 can be broken down to approximately 2 3 of its normal length by removal of the rear leading edges Alternately the Falcon 3 145 170 195 and the Falcon 4 145 170 and 195 when equipped with the optional breakdown configuration can be short packed to less than a seven foot length by removing the sail and further disassembling the airframe This section
47. ck again that the keyhole tangs are fully engaged on the keyhole collar and that the button lock is properly engaged Check that the bolt securing the bottom rear wires is fully engaged in the nut in the keyhole collar and that the collar is securely fastened Check that the sail mount at the rear of the keel pocket is properly attached EM Along the trailing edge right wing Same as for left wing At the right tip Same as for left tip Along the right leading edge Same as for left leading edge Under the glider at the control bar Sight down the downtubes making sure that they are straight Check the cables at the control bar corners making sure that all six cables are properly secured and that there are no kinks or twisted thimbles Check for proper installation of all bolts nuts pins and safety rings at the control bar corners Verify that both ends of the basetube are properly and securely attached to the basetube end bracket and that the speed nuts and safety rings are in place on the securing bolts a Ze Ka F P E E e i i i g n Check the control bar apex bracket hardware including the clevis pin safeties the control bar top plug bolts and nuts and the elbow to apex bracket nut and bolt i Check the main and backup hang loops that they are properly installed in the proper position and that they are in good condition Check the attachment of the sweep wire to the crossbar
48. d 191 vI0c Lc c L00c 0 T UI 1N3AR200 oueJjJly O T y uoo ej OI 4Mdd1S 994 OAT y UO2 j SREL AINO WOLIOS 61 NAHL 8E yoo uoqqng 00 I 9 BOL 91 9404 Uo x ully 91 S 0 WWE 0 x ullyy 91 S 0 WWE 0 x Wupj 91 S 0 WWE 0 x ullyp e Lud Te LV90 866 65 9 866 v1 XV4 Hd e 59876 VI JONVYO e JAY 390143019 00S PNP ESTES pnis u 11eg eoet i SCH hi 994 0ZT y UO9 By ALS JB94 aay p U0I Py ALS app Loo y UO09 ey ALS 3UOJJ 99y y UOD e4 wu uibus OWEN 1Jed MAN uod NOSYVdd VIQc ele 00 0 1 VN j41V O I y L 3 790 866 16569866 PLZ XVdlHd e S98Z6 VO JONVHO e JAY 390183018 005 A EE 03SIA38 Wu 01 1N3n200 QI 4Maq7s g 4eqx OLT y WI 9 N E AN uA NOISIA38 ra ILLE NAHL Z BE Q SL NAHL 61 BE net 89 VOT v80 91 g 0 Wun x wwzg 0892 no S01 09 ALS PALOGIMO Jeqx y uoge EN JeqX OZI y UO2 j K30 1Ub Lo e 14918 N wu y1bu97 y1bu97 OWEN 1Jed mE QuB uy Lu L uod e NOSNV 3d S y102 2 2 L002 0 1 VN HV SOL y UO91 31 500 266 6G 9 066 LZ XVAIHA e S98Z6 VI 39NVHO e JAY 3901830180 Ag SALVLS QdJSIAdH NMVW OT 1N3AQ20Q GI 4Mdd1S 96p3 5 NOISIA38 P3 KEE Sees o c 9 NAHL 61 S 6 00 61 oL 9 61H 00 I Sc 08 0S 00 II 00 vel 0S8 Gil 00 ol Sc 09 00 vv 00 v 119 31 4893 G6T y uO2 j AIS 9 ppiu 3 34044 S6L y uO2 ej
49. d breakdown or in flight To tighten the Velcro grasp the hanging portion of the hang strap with your left hand and pull down while push ing up with your left thumb on the Velcro cinch strap where it passes through the top end of the hang loop At the same time pull up vigorously on the cinch strap and press it into place against the mating Velcro surface Hang loop must be passed through itself to cinch loop Move hang loop towards tail to reduce trim speed Velcro is used tightly to keel lt Hang loop must be centered on bottom of keel when velcro is fully cinched Move hang loop towards nose to increase trim speed Back up loop not shown We recommend that you not stow your glider bag or any other cargo on the glider The practice of attaching your glider bag to the keel for example can drastically alter the pitch trim and static balance of your glider and adversely affect its flying and landing characteristics The best place to carry your glider bag or other cargo is in your harness In the absence of the use of tufts it has become common for pilots to talk about bar position or about indicated airspeed when trying to communicate how to trim a glider properly or how to fly a glider at the proper speed for a given situation The problem is that these methods are unreliable and inconsis tent from one pilot to another even on the same glider The
50. detension and re tension the xbar and sight the hem of the sail at the bottom of the leading edge tube relative to the noseplate on each side Sail tension 1s adjusted by adding or remov ing shims in 1 8 or 1 4 increments to or from the sail mount plugs on the rear ends of the leading edges See the discussion above about the different types of sail mount plugs and how shims are added or removed To remove or add shims from either plug first dismount the sail mount webbing by pulling it free and then to the outside of the leading edge You can use a flat bladed screwdriver to pry the webbing off but take care not to damage the webbing After dismounting the sail first check and record the rotational alignment by noting the position of the scribe mark on the plug relative to the scale on the leading edge tube Use the allen wrench provided In your spare parts kit to loosen the allen screw until you can remove the plug Add or remove shims as necessary and then reinstall the plug making sure the alignment is correct Nine turns of the allen screw after installation of the plug will secure the plug in place Make sure to replace the sail mount screws at the nose Twisting a tip After you have made everything symmetrical if you still have a turn you will correct it by rotating one or both sail mount plugs A left turn is corrected by twisting the left sail plug clockwise twisting the sail down at the trailing edge or twisting the righ
51. e Check for symmetrical twist in the leading edges by checking for symmetry in the alignment of the sail mount plugs Battens Check the battens for symmetrical shape and batten string tension Sail mount plugs adjusting sail tension and rotational alignment The molded plastic sail mount plug fits directly into the rear leading edge It is secured against rota tion by a sliding wedge which is forced out against the inside of the tube as the Allen screw is tight ened The proper installation procedure for this plug 1s to engage the allen screw three turns into the sliding wedge install the plug into the rear leading edge set the desired alignment and then tighten the allen screw 9 additional turns Shims are added to the allen screw type plug by sliding them over the end of the plug before the plug is inserted into the leading edge The shims are thus visible with the plug installed Once the allen screw type plug is installed the rotational alignment can be changed by loosening the allen screw to relieve the pressure of the wedge against the inside of the leading edge tube until the sail mount plug is free enough that it can be rotated If you loosen the screw too much the wedge will fall off inside the leading edge tube and you will have to dismount the sail to retrieve it E Sail tension Check for symmetrical sail tension on the leading edges In order to check this remove the sail mount screws at the nose
52. e crossbar sweep wire and disengage the sweep wire de tensioning the crossbar Remove the remainder of the battens Snap each of the lever batten tips closed before stowing the battens otherwise the tips may become detached and get lost Fold the wings together pulling the sail up over the top of the leading edges Work gently here and alternate from one wing to the other folding each wing in about 1 3 of the way at a time Check to see that the crossbar center has not fallen down between the keel and leading edge on one side If you meet any resistance stop and correct the interference Detach the bridle ring from the snap hook and lay the kingpost down forward against the keel Stow the bridle ring in the loop of bungee attached to the sail at the kingpost base Install the neoprene kingpost cap cover 8 Pull the sail out so that there is even tension on the top and bottom layers and roll the sail towards the keel on each side Try to keep the mylar insert and leading edge area as smooth as possible 9 Secure the sail with the Velcro sail ties provided but do not apply them too tightly The wide long Velcro strap is installed by passing it OVER THE TOP of the keel tube just forward of the control bar top and then installing it around the glider leading edges This holds the leading edges up away from the control bar apex hardware 10 Place the glider bag on the glider and flip the glider over onto the ground 11 Deta
53. e it from the front On the Falcon 3 Tandem the junction of the rear and front leading edges is forward of the leading edge crossbar junction the reinforcing sleeve is internal instead of external and is attached to the rear leading edge instead of the front To disengage the rear leading edge first disassemble the lead ing edge crossbar attachment by removing the safety ring nut and bolt Reinstall the bolt nut and safety ring with the wires attached in the crossbar end Note You will want to replace this safety ring with a new one when you reassemble this junction if the safety ring has been in any way distorted by the removal and reinstallation process Next remove the clevis pin and safety ring located just forward of the visible splice in the leading edge eight inches forward of the leading edge crossbar junction and pull the rear leading edge aft to disengage it from the front Reinstall the clevis pin and safety In all cases cover the sharp edges of both the front and rear leading edge tubes with padding to protect the tubes and the sail from damage during transport Lay the mylar pockets flat so as to avoid creasing the mylar when you fold over the rear portion of the sail Replace the sail ties loosely zip up the bag and carefully fold the rear of the glider over against the front Remounting the rear leading edges l Set the glider on its back upside down Unfold the glider open the bag and lay the sail
54. e to position the washout tube receptacle to the inside of the leading edge Rotate the rear leading edges while maintaining forward pressure on them until the slot on the rear leading edge engages fully on the clevis pin of the front leading edge and the rear leading edges slide into the full forward position Reinstalling the sail on the frame 1 Position the sail on the floor with the keel pocket up and the wings folded over so that the leading edges lie along the length of the root line with the top of the leading edge lying on top 2 Prepare the frame making sure that the side wires are pulled forward from the crossbar leading edge junction and are not wrapped around the frame The outboard crossbars should be swung aft facing the rear end of the leading edges and aligned with the leading edges 45 3 Position the frame with the bottom of the noseplate facing up and with the rear end of the leading edges at the nose of the sail Slide the frame into the nose of the sail taking care not to disengage the rear leading edges from the front and making sure that the leading edges of the frame and the crossbar halves pass properly into the bottom surface of the sail and not into the mylar pockets and that they don t get caught at the rear of the bottom surface near the root Feed the keel outside the bottom surface and through each of the keel pockets As you feed the frame slowly into the sail check periodically to see that none
55. ection of the glider following the procedures set forth earlier in this manual 48 Installing The Optional Litestream Control Bar Kit Owners of Falcon 3 s and 4 s may order an optional Litestream Control Bar kit the kit is not available for the Falcon 3 Tandem We recommend that you have your dealer assist you in the installation of the kit The kit consists of ID Qty Unit Description Appplication AQF 1513 1 EA BASETUBE AL LITSTR W BRK 65 68 195 AQF 1523 1 EA BASETUBE AL LITESTRM W BRKT 62 170 Does 2 EA STREAMLINED BASETUBE SKID 1957170 Lk SES g EA PIN BALL LOCK 1 4 X 33MM GRIP 1957170 406 1471 2 EA LITESTREAM LEG 65 W O BRKTS 195 406 1477 2 EA LITESTREAM LEG 62 W O BRKTS 170 20G 1467 1 EA CB PLUG SET OF 2 LITESTRM TOP 1957170 20G 1468 1 EA CB PLUG SET OF 2 LITESTRM BIM 1957170 It 2 EA BOLT NAS 623 4 21 1957170 10N 1740 g EA CLINCH NUT 1 4 MS21042 4 1957170 106 1290 4 EA CLEVIS PIN MS20392 2629 1957170 10P 1100 4 EA SAFETY RING AN 9491 SMALL 1957170 10T 1103 S EA SPACER AL 250 X 028 X 770 1557170 101 4120 2 EA BUSH 55 sollo X 028 X 650 1954170 LOT 5 003 3 EA SPACER NY 560 X 320 X 187 1957170 456 3058 1 PAIR NEOPRENE COVER SLPSIRM LEG IOP 1957170 Before beginning the installation process verify that all items above are present Note that the down tubes come fully assembled with all hardware attached and that the items designated 10T 1103 in the above list are installed inside the bottom downtube end plugs
56. ed An aggravated spin could result in loss of control in flight inversion and structural failure Therefore no attempt should ever be made to deliberately spin the glider The maximum steady state speed for a prone pilot in the middle of the recommended weight range full forward on the control bar 1s approximately 42 m p h for the Falcon The placarded speed never to exceed and maximum maneuvering speeds for the Falcons are Model Vne Va Falcon 3 4 145 170 195 48 mph 42 mph Falcon 3 Tandem 48 mph 42 mph The Falcon can be flown in steady state high speed flight with the pilot full forward over the bar with out exceeding the VNE speed Abrupt maneuvers may cause the glider to exceed VNE and abrupt maneuvers should not be made from speeds above 42 mph The stability controllability and structural strength of a properly maintained Falcon have been de termined to be adequate for safe operation when the glider is operated within all of the manufacturer specified limitations No warranty of adequate stability controllability or structural strength is made or implied for operation outside of these limitations The stall speed of the Falcon at maximum recommended wing loading 1s 25 mph or less The top steady state speed at minimum recommended wing loading for a prone pilot with a properly de signed and adjusted harness is at least 35 mph All speeds given above are indicated airspeeds for a properly calibrated airspeed indicator
57. eeds just above and just below this speed to find the value of MCA and the corresponding bar position and other indicators for this speed Realize that your effective MCA is going to be higher and higher as the air becomes more and more turbulent control response that is perfectly adequate in smooth air will not be good enough in rougher air Try flying the glider with the midspan tufts fully reversed you will probably find that the glider is somewhat controllable but only with a lot of physical effort Note that both MCA and VMS come well before the glider actually stalls in the traditional sense 1 e pitches uncontrollably nose down You may also be able to sense or your vario may tell you that although the glider has not stalled pitched nose down your sink rate has increased significantly In this mode the glider is mushing Once you have familiarized yourself with the glider s characteristics in this range of speeds you will not need to look at the tufts very often You will know from bar position and bar pressure and from the sound and feel of the relative wind when you are at your minimum sink minimum controllable airspeed In general you should not fly your glider below this speed Be aware however that when you are flying at minimum sink in thermal gusts and turbulence you will experience gust induced separation of the airflow which will periodically cause the tufts on your sail to reverse Of course
58. emove the front velcro sail tie Spread the wings slightly and remove the hang loops and set them aside sg if 1 Insert a 2 Phillips head screwdriver into the rear bolt securing the control bar apex and kingpost P LA n Ee ke ah Be base to the keel Use a 5 16 box end wrench to loosen and remove the clinch nut that secures the kingpost base bracket to the keel Replace the nut on the bolt and tighten the nut one half turn so that it does not come loose and get lost Note When removing the nut use the screwdriver to hold the screw and turn the nut with the wrench as opposed to trying to turn the screw ETLE Remove the screw from the cap on the top of the kingpost carefully remove the plastic kingpost cap and remove the bridle pigtail top rear wire top front wire and both top side wires from the kingpost top Replace the bridle pigtail and re install the kingpost top cap and screw EN i P A 4 Spread out the glider bag and lay the glider on its side on the bag Using a 1 2 inch wrench on the keyhole collar and a 7 16 inch wrench on the bolt remove the bolt securing the bottom rear 4 wire and keel pocket sail mount to the rear of the keel store the bolt in the tang and re install the Detach the bottom side wires from the control bar corners Replace the bolt in the bracket and downtube and tighten the nut 1 2 turn Roll the glider directly onto its back Remove
59. en end of the sail at the tip and slide the loop onto the rear leading edge 46 c Pass the washout tube out of the sail through the hole at the receptacle and position the bungee forward of the washout tube receptacle d Pull the remainder of the washout tube outside of the sail through the hole in the sail at the washout tube receptacle Verify that the rear leading edges are still properly and fully mounted in the front by first pulling aft no more than 1 4 inch then pushing them forward until the front leading edge clevis pin bot toms out in the slot and then try to twist the rear leading edge to confirm that the slot is engaged and it is locked against rotation You will feel some very small amount of rotational play in the slot pin engagement but no more than a very small amount Mount the rear of the sail by pull ing the webbing anchor loops over the rear leading edge endcaps and into the slot in the endcaps Make sure you mount the inner webbing loops in the endcap slots not the outer handle loops Make sure that the webbing lies flat and smooth in the slot and that the sail is properly aligned when mounted not twisted or rotated 180 degrees Secure the Velcro retainer tabs Re assemble the control bar basetube to the downtubes at this time taking care to make sure that the basetube and the front and rear wires are properly oriented Bolt the bottom rear wires to the rear of the keel attaching the rear
60. ents are usually attributed to stalls but it is not the stall per se that causes the problem indeed the glider need not even be stalled in the traditional sense There is no necessary cause and effect relationship between minimum sink speed and minimum controllable airspeed VMS is determined primarily by the wing loading and span loading the wing planform the wing section characteristics etc MCA is influenced most heavily by the tension in the sail how much billow the glider has However in your Wills Wing glider as in most hang gliders MCA and VMS evolved towards a common value during the design and development of the glider This is so because if the wing is tuned so tight that minimum controllable airspeed is at a higher speed 5 than minimum sink speed then effective sink rate performance can be improved by loosening the wing so as to lower the minimum controllable airspeed Conversely if minimum controllable airspeed is reached at a speed below that of minimum sink the wing can usually be tightened so as to improve glide performance without significant sacrifice in other areas Using wing tufts to find the minimum sink speed of your glider On a flex wing hang glider the wing experiences a gradual and progressive stall and different span wise stations of the wing stall at different angles of attack Contrary to popular belief a hang glider wing usually does not stall first in the root or center section
61. er sometimes called a slipping turn is often taught to student hang glider pilots as a way to lose alti tude during the approach While it will work reasonably well with low or medium performance low aspect ratio gliders which have high levels of yaw stability and damping and which are able to lose energy by diving because of the large increase in drag at higher speeds on a high performance glider this technique serves only to convert the energy of altitude to energy of speed while at the same time suddenly increasing the glider s sensitivity to control inputs The result is a high probability of over shooting the intended landing point and the prospect of roll yaw oscillations which may interfere with a proper landing If you develop good habits and the skills to fly precise approaches now it will make your transition to higher performance gliders easier later on 29 Once established on a straight final approach with wings level and flying directly into the wind you should fly the glider down to where the basetube 1s between three and six feet off the ground At this altitude let the control bar out Just enough round out so that your descent is arrested and your flight path parallels the ground The remainder of your approach will consist of bleeding off excess speed while paralleling the ground and keeping the wings level and the nose into the wind until it 1s time to flare for landing Prior to the landi
62. er portion of the tip can be broken if the catch is not released properly before the lever is rotated upwards If this happens simply replace the lever portion by snapping the old one off at the hinge point and snapping a new one on Note that the forward portion of the lever tip 1s threaded into a threaded insert in the rear of the batten and that the tip can thus be turned in or turned out to adjust the overall length of the batten and the tension the batten places on the sail The battens should not be adjusted so as to apply excess chordwise tension to the sail especially on those battens inboard of the crossbar junction On these inboard battens when snapping the lever down into place you should not feel any noticeable tension until just before the lever straightens out and snaps into place and even then the tension should be very light On the number three batten just inboard of the shortest cambered batten which is restrained by a double loop of leech line the tension on the lever tip should be somewhat higher The adjustment of the string tension on the number two batten should be firm M o 11 Install the washout tips by plugging them straight into the receptacles in the back side of the leading edge tube Make sure they are inserted as far as they will go and that there is tension on the bungee holding them in place Verify that the transverse batten that the washout tube supports is properly located and secure in the sail b
63. erating under this exemption must be individually authorized to do so by the ex 6 emption holder and must operate under all of the requirements of the exemption in order to conduct legal two place flight operations It is the pilot s responsibility to have the necessary skills knowledge and experience to obtain the proper authorization to operate under the exemption and to operate un der the requirements of the exemption Tandem or two place hang glider flight requires special skills experience and knowledge that are far beyond what is required for single place operations Based on flight testing and other testing conducted by Wills Wing on the Falcon 3 Tandem glider we believe that the Falcon 3 Tandem is suitable for two place flight provided that the pilot in command has all the necessary knowledge skills and experience to conduct such flight operations safely and follows all appropriate procedures for safe two place flight The Falcon 3 Tandem model can also be flown single place by a pilot within the recommended weight range and in the case of single place opera tion a minimum USHGA Novice II level of pilot proficiency is required to fly the Falcon 3 Tandem safely unless under the direct supervision of a qualified instructor This information covers only the Falcon 3 Tandem see the appropriate Owner Service Manuals for important information about previous Falcon Tandem and Falcon 225 models A Note About High Dut
64. ess JeqssoJj Uu 0088 00 72 J10H YVEX 6700 7 19 i zl 00j ZL 00 8l H 00 01 6700 076 6700 8 10 L Ud W ED 00Z 001 P be uld IL ED 00 mmm 00 09 le 061 09 0S1 08709 SLO Gi YE 3J IS JNO 8 1 1V 13Al4 S On l SB 0S EL EJE 00 0l 9bp3 buipea juoJ4 00 szl 00 EH 009 DU NIU S 0 St 09 nJUl AC O 0S8 ER 59200 XZ AAA a e on ooo AAA SWE JJ L uod e NOS V3d VIQc e 00 0 1 VN LIN GpT y L 3 7790 866 6SE9 866 PLZ XvdlHd e S98Z6 V9 J9NVHO e JAY 390I4IN18 005 de EE GESEIS Wun 01 1N3n200 QI Magis obp3 Burpee opt y uoo e4 G IZ A AT SA NOISIA38 SREL LZ 61H 00 1 6U 1018 0 LZ 0 NAHL 6U see 00 61 Sc 09 00 cl Us 09 86 0S8 OTI 00 Sl I GN 91 S 0 uug Q x u 0s y8 1 S204 I 6U 0 91 S 0 uug Q x WEG OT9 00 v2 00 91 9404 uug Q x We 201 680 91 g 0 uuo 0 x uuog 8062 ALO EEN e 1J 1eN uu q35u93 uMopxyeaug 3 JeaM GYI y uodle4 ALS 9 ppiu 3 JUOU4 GYI y UO9 By 00 v CALS 3 10044 obt y UO9 Py 08 VII J 14043 Sy y UOO ej u35u OWEN 1Jed 1911 SCHER dp NOISIA38 VI0c Lc c L002 0 T 9UEJJJLV GYI y UOOLP4 EE 03SIA38 Wu 01 1N3n200 QI 4M00TS alae to SOT AINO WOLLOG et o 9 cel 91 S 0 Uuo 0 x fit SI 91 S 0 uUo 0 x Ullyy 6cc er DEE 91 S 0 WWE 0 x Wupj 91 S
65. etween the number 2 and number 3 battens Install the straight plug on 1 battens Insert one end of the batten through the gap in the stitching in the bottom surface seam This end plugs onto the stud on the back side of the leading edge and the batten string is secured by a double purchase to the other end mmm 12 At this time preflight the following from the open end of the wingtip a The sail mount webbing make sure that the inner loop of webbing is laying flat In the bottom of the slot in the sail mount endcap b The number one batten clevis pin Note that on Falcon 3 s assembled prior to 9 8 2006 the pin is installed from the front side of the leading edge tube and is secured with a push nut flush against the back side of the leading edge tube and that there is no retaining washer on the pin no sleeve over the pin and no safety ring in the pin Because of the manner in which the batten is held In place these are not necessary to retain the front of the batten However it is possible for the pin to be pushed back into the leading edge tube from the backside if the push nut fails to hold it On Falcon 3 s assembled after 9 8 2006 the pin is installed from the backside of the leading edge tube and is stood off from the 4 tube surface by a short 1 4 inch diameter sleeve and secured on the front side of the leading edge tube with a small safety ring covered by protective tape If you have a prob lem with the ear
66. ez x qu en X SZ l ANNOY 89 931 0OSZI D0Y zz Ca Je Y9 X S60 X Sz I 3gn13Svg O09 1 30v 12 MEA 1949249 eseg uepue uod e4 WESSEN Ze uepue u0929 e4 MOQJj Jeg VEL DOS 61 VELO J07 ST SH El EE 9T sob sol zi OvIT Nol Vi VCELI 10I el OO 1401 cl OOTT dOl ER OV I NOlI 0T Uspubj uoopePj 419 194 194319 u pue uoo ej doj nid dJeq2 NVO4JA10d 390143SV9q dIq49 020 X 9I X SZ NOTAN YSHSVM AJIHL v I 9Iv 096NV 13415 YIHSVM BS Ke NI NI SL LA 690 A S 1 daduds Sech cu NV INTE AL34VS TIVWS Tove NV INIA ALAAVS v cVOTCSW v T LAN HONT IO 8 X V T LANG44dS GbvT NOT G S9ENV 9T S 1ANAJO 1 O OT NOT V 1I1W130 N ENEE Cl SE ia S00C ZT 00e L1 v woog 1 UM WOPueL U09154 7490 866 6689 9866 PLZ XVAIHA e S98Z6 VI 39NVHO e JAY 3901301800 T XXXX SNLVLS Q3SIA3H Mu WI QI 4Maq1s XXX og voee aoz Assy was m puel uoolej NEAS STAAN 9JLM 3 OF woog Le u pue UOd e4 3JIM I9vv dOv T 8T TIVWS 676 NV 9NIU Al3dVS O0II dOI c ZT 2 26t025W Oztl 901 2 9I 01 sol T HS 8 M N43ISNIJ 133HM G2OT WOZ T vl HA VEZ 2 OU Y er g3 OL N0081IV1 WIONVL NOOIVd 3YIM I9vv dOv 2 l 850 8 T T dVOUN3 SIII 88T 2 IT XV uM e uepuej uoo ej 0 902 I 6 LLL MEN vuv 2 LR Y ZYOIZSW v T LAN HONIIO OVZT NOT S Z A9IH1 7 1
67. flare run combination will bring the glider quickly to a very nose high attitude producing a great deal of drag and quickly arresting all of your forward motion You will feel the glider pulling you from behind resisting your attempt to run and as you slow down the glider will settle gently on your shoulders Even in no wind you should not have to take more than a few steps If your timing is a little early and you feel the glider start to climb simply stop pushing out and resume the flare when the glider again begins to settle If your timing 1s a little late your feet will touch down a little sooner but as long as you re running and flaring at the same time the glider will stay over your head or behind you Note Landing in a significant wind does not require a substantial landing flare the pilot merely slows to near zero ground speed and touches down The proper flare in light or no wind conditions is a dynamic action which causes a sudden and severe pitch up rotation of the glider Pilots who have trouble with the flare and with the glider nosing over during landing usually do so because of one of the following problems EM y n a Harness leg straps too long hanging too low below the glider and or hands too low on the con trol bar This reduces pitch authority and prevents an adequate flare b Improper body position pilot leaning back away from the anticipated hard landing with feet extended in front This moves the
68. he first onset of midspan stall as indicated by the first tickling of the tufts indicates that you have reached the angle of attack corresponding to the glider s minimum sink airspeed This will also be very close to the glider s minimum controllable airspeed To find the glider s minimum sink speed fly the glider in smooth air early in the morning or late in the afternoon When you are well away from the terrain and well clear of other aircraft look up at the wing tufts while you very gradually reduce the speed of the glider Note the speed at which the first tuft first begins to wiggle just prior to blowing spanwise toward the tip If the tufts contain static electricity they may not show this lat eral wiggle prior to reversal However you may get other clues to the beginning of separation such as slight flutter or rumble in the top surface of the sail This is your speed for minimum sink rate 24 Familiarize yourself with the position of the control bar relative to your body at this speed with the sound and feel of the wind with the reading on your airspeed Indicator and with the feel of the glider in terms of pitch and roll pressures Most of the time when you are flying it will not be practical to look up for extended periods of time at your tufts That is why familiarization with these other more accessible indicators 1s important After finding your minimum sink speed experiment with roll control response at sp
69. hole to l Crossbar attachment hole 147 2 Rear sail attachment point 244 5 245 25 b Outside diameter at 1 Nose 2 00 2 Crossbar 2 00 3 Rear sail attachment point 2 00 Crossbar Dimensions a Overall pin to pin length from leading edge attachment point to hinge bolt at glider centerline 129 21 b Largest outside diameter 2 9 Or 2 44 Keel dimensions least and greatest allowable distances whether variable through tuning or through in flight variable geometry from the line joining the leading edge nose bolts to a The xbar center load bearing pin 57 7 25 b The pilot hang loop 70 75 1 5 Sail Dimensions a Chord lengths at 1 ft outboard of centerline 102 3 2 3 ft inboard of tip A8 b Span extreme tip to tip 430 Location of Information Placard Kee Location of Test Fly Sticker Kee Recommended Pilot Weight Range 185 500 Recommended Pilot Proficiency USHGA Novice NOSYV3d VI10c 9c e L002 0 T VN 9UEJjJLV GYT U02 8J A EE GESEIS Wun 01 1N3W0200 QI 4M00TS LV90 866 6GE9 866 VL XYd Hd e 69826 VI 3DNVHO e JAY 390143018 00S ebpe Butpe 1 opt uoo e4 SJN IDA STE NOISIA38 SREL ee H DH ZI u alc EE D I GL 0S OTT 00 ce US SEI 00 8I 7 36 9y SZ vol rS I 91 S 0 v8 I 96 UL eqni 3 seed Syl u0 ej UO 91 9404 me 1008 ZALS Ipptu 31 10041 SpT uooej I 091 91 8 0 vo 1 Se 0 ALS 9 pptu 4 10044 Gbt u02 ed 91 S 0 COL 00 v CALS 4 34044 GPT UO2I
70. ill compromise your safety b Itis only accurate when within 15 20 degrees of the vertical orientation Landing The Falcon We recommend using an aircraft landing approach 45 entry leg downwind leg base leg and final leg whenever possible and we suggest that you practice making your approaches with as much precision as possible Under ideal conditions landing approaches are best done so as to include a long straight final into the wind at a speed above best L D speed In a very limited field or a field which slopes slightly downhill when landing in light wind you may need to make your final approach at a slower speed perhaps as slow as minimum sink in order to be able to land within the field In winds of less than 5 mph if the slope is steeper than 12 1 you should seriously consider landing down wind uphill or crosswind across the slope Landing attempts which require slow speed approaches maneuvering around obstacles or into a restricted area or downwind or crosswind landings are not recommended for pilots below an advanced skill level Standard Aircraft Approach Pattern Entry Leg Downwind Leg 77 Base gt d Final The best way to avoid roll yaw oscillations on approach 1s to fly your entire approach at a constant airspeed and to control your touchdown point by making adjustments to the shape of your pattern In particular we recommend against the technique of make a diving turn onto final This maneuv
71. in a turn your minimum sink speed goes up because you are banked and the bank effec tively increases your wing loading which increases your flying speed for any angle of attack But note this The tufts indicate angle of attack without regard to airspeed Therefore if you practice flying various bank angles in smooth air while well away from any terrain or other gliders and watch your tufts on the inside wing which will be at the highest angle of attack you will get a feel for the way your minimum sink speed varies at varying bank angles One final caution from time to time a tuft may to stick completely to the sail and fail to properly indicate the direction of local flow This may result from static buildup or from the fine threads of the yard becoming caught on a seam or some dirt or imperfection in the sail The tuft may stick while in dicating normal flow but most often it will stick after having reversed such that the tuft will indicate a stalled condition that does not exist One clue in this situation is to note whether or not the tuft is wiggling Since flow reversal occurs during a turbulent separated flow a reversed tuft should be wig gling rapidly If it is not it is probably stuck A tuft indicating normal flow will not usually wiggle An occasional application of silicone spray to the tufts and making sure that they are positioned so that they cannot catch on any seam will minimize the problem of sticking 95 Trimm
72. ing Your Glider In Pitch The fore and aft location along the keel of your hang point is commonly if mistakenly referred to as your CG location The location of this hang point will all other things being equal determine at what angle of attack and airspeed your glider will naturally tend to fly or trim and therefore how much bar pressure there is to pull in from trim to a given faster speed or how much pressure there is to push out from trim to a given slower speed The farther forward your hang point is the faster the glider will trim the less effort will be required to fly fast and the more effort will be required to fly slow Since the Falcon performs best at speeds relatively close to VMS it is usually best to trim the glider at between minimum sink airspeed and perhaps 3 mph above that The pre set factory position for the main hang loop 1s Falcon 3 145 170 2 5 inches forward of the horizontal apex bolt Falcon 4 145 170 Falcon 3 195 Flaocn 4 195 3 25 inches forward of the horizontal apex bolt Falcon 3 Tandem For tandem flight 3 25 inches forward of the horizontal apex bolt For solo flight 2 75 inches forward of the horizontal apex bolt Hang loop fore and aft position is adjusted by loosening the Velcro cinch strap on the main hang loop repositioning the loop as desired and retightening the cinch strap This strap must be very tight to insure that the hang strap does not move during set up an
73. keel tension the crossbar by pulling on the rope loop which is attached to the sweep wire keyhole tang Drop the keyhole tang all the way down over the top portion of the key hole collar and let it slide forward into the locked position The button lock should snap up into place behind the rear end of the tang Next attach the keyhole tang for the top rear wire and again 10 Never install the keyhole tangs onto the keyhole collar without making absolutely sure that they are fully engaged on the narrow neck of the collar and slid forward into the fully locked position An in flight disengagement of this attachment will cause a complete loss of structural support of the glider and a total loss of control Remove the tip cover bags and install the remaining cambered battens Secure the number two batten shortest cambered batten with a double purchase attachment of the batten string At this time you can engage all of the lever tips in the trailing edge hem using the following procedure First unlock the catch on the lever portion of the tip by squeezing upwards on the bottom of the lever portion just behind the catch while applying a slight downward pressure to the lever tip This will release the catch and allow you to pivot the lever section upwards Next fit the end of the lever portion into the gap in the trailing edge hem as shown and then rotate the lever portion down until it clicks into place Note that the locking catch on the lev
74. lier configuration we recommend that you convert to the later assembly Note also that the number one batten can become disengaged in flight if the retaining string is too loose The string should be adjusted as tight as it can be without being so tight that it slackens the sail mount webbing or pulls the webbing away from the slot in the endcap 13 Go to the nose and attach the keyhole tang securing the bottom front wires by pulling down on the nose of the glider while pressing the tang upwards over the shouldered bolt Remember it is the pulling down of the glider s nose rather than the upward pressure on the tang that allows you to install the tang over the bolt If you have difficulty installing the tang and no wires are twisted or thimbles cocked it is probably because the glider is not sitting on level ground 14 Make sure that the spring loaded button lock pops up behind the tang securing it In place 15 Push the nose batten fully back into the sail and lift the open end of the batten onto the stud on the top of the keel Look into the noseplate and preflight the top front wire Preflight each of the lockuts on the bottom of the noseplate make sure they are tight and that the bolt extends at least one full thread beyond the nut E E Install the nosecone by pulling the bottom tabs forward and down around the nose and mating the velcro surfaces on the tabs to those on the sail Make sure that the nosecose lies as flat
75. lls Wing gliders and products a Wills Wing Dealer directory a comprehensive list of service and technical bulletins current editions of owners manuals our complete retail price list a search engine and more Our web site is the means by which we will communicate with you when we have service advisories or other information related to your safety that we need to make you aware of We wish you a safe and enjoyable flying career and once again welcome aboard Mike Meier Linda Meier and Steve Pearson Wills Wing Inc Disclaimer And Warning Hang gliding is a form of aviation Like any form of aviation its safe practice demands the consistent exercise of pilot skill knowledge of airmanship and weather judgment and attention at a level which Is appropriate to the demands of each individual situation Pilots who do not possess or exercise the required knowledge skills and judgment are frequently injured and killed The statistical rate at which fatalities occur in hang gliding is approximately one per thousand participants per year The Federal Aviation Administration does not require a pilot s license to operate a hang glider Hang gliders and hang gliding equipment are not designed manufactured tested or certified to any state or federal government airworthiness standards or requirements Hang Gliders are not required to be registered with the Federal government As a result we do not have a reliable way to keep track of contact info
76. lp determine when you are flying at minimum sink airspeed There are two important airspeeds with which all hang glider pilots should be intimately familiar minimum sink airspeed hereinafter referred to as VMS and minimum controllable airspeed MCA The most important of these two is MCA Minimum sink airspeed is that speed at which your descent rate is the slowest possible It is the speed to fly when you want to maximize your climb rate in lift or slow your rate of descent to a minimum in non lifting air You would normally not fly at VMS in sinking air the strategy there is normally to speed up and fly quickly out of the sink By minimiz ing your time spent in the sinking air you minimize altitude lost even though you have momentarily increased your sink rate by speeding up Minimum controllable airspeed is that speed below which you begin to rapidly lose effective lateral control of the glider Recognition of this speed and its implications is a more subtle problem than many pilots realize We have seen several instances of pilots who were having a lot of trouble flying their gliders simply because they were unknowingly trying to fly them too slowly below the speed at which the glider responded effectively to lateral control inputs It is our opinion that a great percent age of hang gliding accidents are caused by inadvertent flight below MCA and subsequent loss of control of the glider with impact preceding recovery Such incid
77. mounted in the vicinity of the pilot Such an airspeed indicator 1s available through your Wills Wing dealer The recommended hook in pilot weight range for the Falcon 3 and Falcon 4 1s Falcon 3 4 145 120 190 lbs Falcon 3 4 170 140 220 lbs Falcon 3 4 195 175 275 lbs Falcon 3 Tandem 185 500 lbs Be advised that pilots with hook in weights within 20 lbs of the minimum recommended will find the Falcon somewhat more demanding of pilot skill to fly and that pilots with hook in weights of more than 130 of the minimum recommended will experience some relative degradation of optimum sink rate performance due to their higher wing loading Please note that the term recommended hook in pilot weight range comes from the HGMA certification standards and without some qualification may be misleading The recommended weight ranges as listed above represent the full range of pilot hook in weights over which the model listed will retain adequate stability performance control and 4 _ structural strength A more appropriate term for the weight ranges listed above might be the allow able pilot hook in weight range The pilot hook in weight ranges which we would actually recom mend as being optimum are given in the following table The optimum hook in pilot weight range for the Falcon 3 1s Falcon 3 4 145 140 165 lbs Falcon 3 4 170 165 200 lbs Falcon 3 4 195 200 240 lbs Falcon 3 Tandem 240 450 lbs
78. n Flare too late and you won t get the nose up enough to stop your forward motion and the glider may nose into the ground as you run into it from behind The flare timing process is made much easier by using a combination of a crescendo flare and a run out of the landing As you bleed off speed on final flying just above the ground you are at first letting the control bar out towards its trim position As the glider reaches trim speed which will normally be one to three mph above stall speed you begin to gently push the bar out to keep the glider from settling At this point it is almost time to flare As the glider enters the mushing range of angles of attack it will begin to settle in spite of your continuing to ease the bar out This should be hap pening well before your arms are significantly extended At this point begin your flare by smoothly accelerating the rate at which you push out on the bar At the same time draw one leg forward put a foot down and start to run as hard as you can This run should be very much like an aggressive take off run your body should be leaning forward into the run and you should be driving with your legs The difference here 1s that while you are leaning into your run and driving forward with your legs your arms are extending fully from your shoulders pushing out and what feels like upwards on the control bar in an accelerating crescendo flare Done correctly this type of
79. n the tang at the bottom towards the basetube that the wires are routed properly and do not cross over or wrap around any other wires or components and that no twist has been induced in the side wires Re install the knurled bushing knurled portion last into the bottom downtube plug and press it in until it 1s flush with the surface of the plug 5 Install the basetube using the ball lock pins provided and do a full set up and inspection of the glider 50 Tuning Dismounting and remounting the sail at the tip A number of tuning procedures require you to dismount the sail at the rear leading edge This can be most easily accomplished by using a large flat bladed screw driver to pry the sail mount webbing off of the end of the leading edge The same technique can be used to reinstall the sail Take care not to damage the sail mount webbing and when remounting the sail be sure to mount the inner webbing in the slot not the outer handle webbing and be sure that the webbing seats squarely in the slot CG adjustment has already been covered in the section of this manual on using your wing tufts Wills Wing recom mends that tuning other than CG adjustment be performed by your Wills Wing dealer Turn trim Turns are caused by an asymmetry in the glider If you have a turn first try to make the glider sym metrical in every way Airframe Check the leading edges for possible bent tubes Check that the keel is not bent to one sid
80. n8 3901 1nOHSVM vHTI WOY WEE E ee NOITY Y3LSNCOW TIWS QuvOvId 6105 902 M3YIS dei YILSNCOY TIVS dI12 2 Itten OT O96NY 1331S YIHSVM O TT noT SS GL TXZE 0T dVO L3320S M3N2S 9202 300 dV20N3 1snr v 3017S ININDOT ztet egt 318VISNCAY LNNOW lIVS dun TT6T CST eee NN ze dE d vc D I I T I I WEE A AA C C C e C 318 1d Ge 8002 1 3 00c ce 6 V 91P10950U UOJI 1 490 966 6669 866 PLZ XVAIHA e 39826 VI 39NYHO e JAY 190IYINTE 005 Sn1VIS 3STLAdd CI LNAWN900 01 200 NOISIA38 ASSV LAN AV CIOJ 310HA 3 SU5c 9UG CELE YAJMS TIvg 1NO43 dOl 34IM L0te d0v V9C VNV I966 VOI VU NN He MOI 2002 IVSSaATNI 31Vld3SON Bede JU v cVOLCSW VAL LAN HONITO OvZT NOL L0ct dOv 8l X 02 X 095 AN Wu3ovds 0IS 101 La NIHL kat 91v 096NV 1331S YIHSVM IFII nOI Ep Sg 201 NING 310H3 M ASSY 002 3lVldN 6 91 902 T AL0 u02 uoi3drJo5sag KEN WILI _s _ 0T OMS 11V8 LNOYS WLLOd LAS d43IM Ge La pans SE 2 RE Lv90 866 65 9 866 VLZ XV4IHd e a98c6 VI 3DNVHO e JAV 390143019 00S Ag SAIVLS 3511734 NMV30 OUT 1N3WNIO0 dI 3M001S seg 1041002 meet geet NEAR Sq NOISIA38 3 1111 gd 1IV130 Poza OD vay WOLLOS 13S 38IM eoee dor 92 NYL 1NOY4 WLLOG 13S 38IM vOZE d0Y S2 31ALS LY 8 1 3015 WOLLOS 38IM POTE dOv vz 2 NN01140 960 X SZ I S114 14 S 3A331S SSZI D0p
81. ng flare your body position should be generally upright but slightly inclined for ward with your head and shoulders forward of your hips and your legs and feet trailing slightly behind Your hands should be at shoulder width and shoulder height on the uprights You should be relaxed with a light grip on the bar and your weight should be fully supported in your harness and not at all by your arms There are several options for when to make the transition from prone to this semi upright position Some pilots favor going upright with both hands moving to the downtubes while still at altitude prior to the start of the approach Others transition at the start of the approach to a semi upright position with one hand on a downtube and one hand on the basetube and complete the transition by moving the other hand to the downtube just a few seconds prior to flare Still others fly with both hands on the basetube until established on final glide and then transition one hand at a time to the downtubes prior to flare Whichever method you use there are a few important principles to observe The first is that you should not make any change in hand position unless you are flying at or very near trim speed At speeds faster than trim you will be holding the bar in pitch against substantial force and if you let go to move your hand the glider will pitch up and roll towards your remaining hand The second is that while moving either hand you have no control
82. of the hardware is snagging on the sail As the crossbar ends reach the leading edge junction cut outs in the sail bring them out through these holes After the frame is fully inserted swing the outboard crossbar halves forward Working through the crossbar cut out hole insert the top wires through the holes in the sail making sure that no cable is wrapped around a leading edge or crossbar and that no thimbles are cocked or twisted Pull the bottom side wires out through the crossbar cut out hole Feed the top front wire through the hole in the sail Attach the sail mount tangs to the leading edge tube with the screws near the noseplate Prop the nose of the glider on the short pack box and spread the wings slightly Position the crossbar center section as shown and feed the crossbar center into the glider around one side of the keel s a s j F rE When properly positioned the crossbar center should lie below the keel because the glider is upside down with the central nut on the center hinge bracket joint facing the floor Install the in ner crossbars onto the outer crossbars matching up the alignment marks and secure by installing the clevis pins and safety rings Feed the top rear wires and crossbar sweep wire along the keel through the keel pockets and out the rear of the sail Install the washout tubes as follows a First make a loop as shown in the bungee b Next slide the long end of the washout tube into the op
83. oper state of tune and repair to insure optimum alr worthiness performance and flight characteristics Failure to properly maintain your glider may lead to a dangerous loss of strength stability or control responsiveness of the glider Following any mishap that results in damage to the glider immediately have any damaged component repaired or replaced We recommend that you have all such maintenance work done by your Wills Wing dealer In addition please follow the following maintenance schedule Maintenance intervals are expressed in terms of calendar months and number of flights You should perform the indicated maintenance at whichever comes first Every month or every 30 flights 1 Check your battens on a flat level surface following the instructions on the batten diagram pro vided and correct any that deviate from the pattern in accordance with the instructions Every six months or every 150 flights 1 Have a complete inspection performed on the glider and replace any component that shows any wear and any cable that shows any kinks wear damage corrosion etc 2 Inspect all bolts for tightness all safeties for proper installation and possible damage Inspect plates and fittings for damage holes in tubes for elongation 3 Inspect the sail for wear tears UV damage loose stitching etc 4 Disassemble the control bar corner assemblies Inspect the hardware fittings and the cable termi nations on the front and rear flying wires
84. ore beginning Note The short pack procedures below incorporate the use of the optional short pack storage trans port container a specially designed combination box and heavy duty zippered bag designed to con tain and protect your glider during storage and transport in the short pack configuration The container is available through your Wills Wing dealer or direct from Wills Wing 37 Falcon Shortpack Bag Box We offer different length box assemblies for each of the Falcon 3 models and Falcon 4 s with the short pack option with the exception of the Falcon 3 Tandem which cannot be short packed 45G 1310 BAG BOX GLIDER SHORT PACK 84 Falcon 3 195 45G 1311 BAG BOX GLIDER SHORT PACK 78 Falcon 3 170 45G 1312 BAG BOX GLIDER SHORT PACK 72 Falcon 3 145 Each of the short pack kits itemized above includes 1 tools necessary to break down the glider fol lowing the procedure illustrated in the glider owners manual 2 a heavy duty bag with plastiboard liner and wheel assembly 3 batten studs with threaded couplings to modify longer Falcon battens to fit in the breakdown box The tool kit 4 in 1 Screwdriver 1 and 2 Phillips 1 and 2 flat 3 Phillips bit to fit 1 4 inch phillips NAS517 bolts at the kingpost 5 16 wrench to fit 1 4 inch clinch nuts 7 16 wrench to fit 1 4 inch nylocks 1 2 wrench to fit keyhole collar at the rear wire junction These are the tools you will need for service work on the Falcon
85. out full length Make sure you are mounting the correct leading edge rear into the correct front check the right left designation and remember that left right are reversed when the glider is lying upside down on its back Wipe the forward six inches of the rear leading edge with a clean cloth to remove any dirt or grit o Slide the rear leading edge tube into the sail and then into the front leading edge as far as it will go until you encounter a hard stop This will be the forward edge of the rear leading edge con tacting the clevis pin in the front leading edge On the Falcon 3 Falcon 4 145 1770 and 195 rotate the rear leading edge so that the washout tube receptacle faces inwards towards the opposite leading edge and then continue to rotate the leading edge slowly so as to rotate the washout tube receptacle towards the ground upwards relative to the glider while maintaining forward pressure on the rear leading edge until you feel the rear leading edge slide forward as the slot in the rear leading edge engages on the clevis pin Verify that the rear leading edge is as far forward as it will go and that it is locked against rota tion by the engagement of the slot on the clevis pin On the Falcon 3 Tandem remove the clevis pin and safety in the front leading edge and slide the rear leading edge all the way forward Rotate the rear leading edge so that the washout tube receptacle faces inwards toward
86. over the glider You should move only one hand at a time Even so if you can t make the transition in the position of each hand quickly and reliably you should transition both hands while at altitude before you start your approach Otherwise if you fail to make a quick transition you could be out of control close to the ground and suffer a turbulence in duced change in heading or attitude without sufficient time to recover Many pilots make the mistake of trying to change position while flying fast and close to the ground and experience a dangerous loss of control as a result A third principle to observe 1s that if you are using a pod type harness you should unzip and confirm that your legs are free to exit the harness at least 500 feet above the ground and before you start your approach If there is any problem finding the zipper pull or dealing with a stuck zipper you don t want to have to try to fix that problem while also flying the approach Finally you should not attempt to get into a fully upright body position at any time during the landing approach prior to the actual landing flare Most modern harnesses will not allow you to hang in a fully upright position without pulling yourself up on the downtubes and this is something you should NOT do The mechanism by which you attain an upright position at the moment of touchdown is to ex ecute a strong flare which causes the glider to slow abruptly causing you to swing fo
87. r light headwind you will want to fly in the upper half of this range Green The top of the green region represents the placarded maximum rough air and maximum maneuvering speeds This speed of 46 mph should not be exceeded except in smooth air and no abrupt large control deflections should be used above this speed In heavy sink or strong head winds it is recommended that you keep the airspeed in the green for best penetration and glide ratio over the ground Yellow This region represents the upper speed range between maximum rough air maximum maneuvering speed and the speed never to exceed You should fly in this range only in smooth air as described above Red Line This is your never to exceed speed At no time should you fly faster than this speed Color Coding 53 mph Red 46 b3mph Yellow 30 46 mph Green The design of the Hall type airspeed indicator involves using a ram air versus static pressure differential to raise a disc in a tapered tube against the force of the weight of the disc Because of this the ASI has the following operating limitations EN M a Itis only accurate in one G flight If you are turning at a bank angle of more than 30 degrees the ASI will read artificially low as a result of the G loading of the turn Reliance on the ASI for limiting airspeeds in high banked sustained spiral maneuvers will likely cause you to exceed the placarded speed limitations of the glider and w
88. rmation for the owners of Wills Wing hang gliders It is your responsibility to check with us periodically for safety and airworthiness advisories and information related to your glider The easiest way to do this is to check our web site at http www willswing com Wills Wing hang gliding products are not covered by product liability insurance You should never attempt to fly a hang glider without having received competent instruction We recommend that you not participate In hang glid ing unless you recognize and wish to personally assume the associated risks Please fly safely Wills Wing Inc Technical Information And Placarded Operating Limitations This manual covers the Falcon 3 145 170 195 Falcon 3 Tandem and the the Falcon 4 145 170 195 These gliders have been tested and found to comply with the 2008 HGMA Airworthiness Standards HGMA Certificates of Compliance were issued for each of these gliders on April 20th 2009 The Falcon 4 145 170 and 195 have been tested and found to comply with the 2014 HGMA Standards At the time of this writing June Ist 2015 no certificates of compliance have been issued for these models Please see www HGMA net for updated information on the HGMA certification status of any hang glider The HGMA Certification standards require l A positive load test at root stall angle of attack at a speed equal to at least the greatest of a 141 of the placarded maximum maneuvering speed b 141 of
89. rward and into a standing upright position underneath the glider The more upright you try to be prior to the flare the more you move your shoulders back relative to the center of mass of your body which effectively shortens your arms and weakens your flare authority Keep your head and shoulders forward and your feet and legs back with your body in a semi upright position until it is time to flare and then flare from this position Once established on a wings level short final into the wind body semi upright and with both hands on the downtubes your final concern is the timing and execution of the landing flare The goal is to arrive on the ground on your feet under control with the glider settling on your shoulders If the wind is 15 mph or more you will not really execute a flare at all you will simply slow to minimum flying speed put a foot down and step onto the ground In lighter winds you will want to use some combi nation of a final nose up flare and running out your landing in order to finish the flight on your feet with the glider settling on your shoulders The lighter the wind the stronger should be both your flare and your run The traditional method of landing in light or no wind calls for a sharp aggressive flare at precisely the correct moment This technique works fine when done correctly but it s not easy to get the timing just right Flare too early and you will climb and then fall with the nose pitching dow
90. s require the following fasteners which we include with the kit 2 5mm screw x 20mm PHP 8 pitch 2 5mm screw x 16mm PHP 8 pitch 2 4mm screw x 14mm PHP 7 pitch 4 4mm fender washer 4 5mm fender washer 4 5mm nyloc 2 4mm nyloc Mount the wheel assembly using the fasteners shown in the diagram below Use 5mm flat washers on the inside of the container Use 4mm washers on both sides of the container Gmm xl mm Use 2mm C small OD flat washers on the inside of container at locations on lona 2mm x ZOmm side of L wheel bracket Bottom short lea Amm x 4mm bolt and nut use 4mm Clarae OD flat washer both sides at these 2 locations The preferred orientation of the fasteners is with the heads of the screws on the insde of the container and the locking nuts on the outside however that fastener orientation requires a 5mm metric socket to tighten the nuts If you don t have a 5mm metric socket insert the screws from the outside and hold the nuts on the inside with pliers while you tighten the screws 40 Sail removal You will need an unobstructed area six feet by thirty feet Make sure the surface is clean If it is abra sive like rough concrete you should either put down a protective tarp or be extremely careful not to scrape your sail l Assemble the control bar set the glider upright on the bar and remove the bag as if you were beginning the process of setting the glider up to fly R
91. s the opposite leading edge and then continue to rotate the lead ing edge so as to rotate the washout tube receptacle towards the ground until the clevis pin holes line up Re install the clevis pin and safety taking note that the safety is installed on the top of the leading edge which will be on the bottom at this point because the glider 1s upside down On the Falcon 3 Tandem reassemble the leading edge crossbar junction Refer to the diagram note that the diagram depicts the assembly right side up whereas you will be working on it up side down and note that the bolt is installed from below with the nut and safety ring installed on top of the crossbar On Falcon 3 Tandems manufactured prior to November of 2007 this assembly used an AN4 32 bolt and a castle nut non self locking nut with a slotted top Later Falcon 3 Tandems use a longer AN4 33 bolt and a clinch nut self locking in this application The other 3 Falcon 3 sizes were also changed from a castle nut to a clinch nut at this time how ever they do not require a change to a longer bolt Because the castle nut has no self locking feature if the safety ring 1s not present the nut can eventually loosen up and fall off allowing the entire assembly to come apart in flight We therefore recommend that if you have an earlier model with the castle nut in this application you consider converting to the clinch nut In either case when reinstalling the safety ring inspect it
92. sail mount at the same time Install the control bar downtubes onto the plugs at the apex bracket and attach the bottom side wires to the control bar corners Flip the glider up onto the control bar Pull the crossbar sweep wire tang out through the kingpost hole and pull tight on the sweep wire while looking up into the sail towards the crossbar center Correctly position the left and right sweep wires on the proper sides of the top centerline of the keel _ a 10 Re insert the sweep wire into the kingpost hole and down along the top of the keel into the rear keel pocket Install the kingpost base bracket onto the top of the keel keeping the sweep wires properly positioned on either side of the kingpost Pass the top rear wire out of the rear of the keel pocket and feed it between the left and right bridle cables and under the bridle cable ring Remove the kingpost top cap and bridle pigtail and place the top front top side and top rear wires ball swages in the kingpost top Install the bridle pigtail in the kingpost top on top of the top rear wire and install the kingpost top cap and screw Spread the wings slowly and carefully making sure that the sail does not catch on any hardware and that there are no improper assemblies restricting the deployment of the wings If the bridles were disconnected from the sail as part of a sail repair re connect them to the sail at this time Proceed with a normal setup and complete pre flight insp
93. stand under the rear keel so that the tips are completely clear of the ground String a lightweight piece of thread from the rear tip of each bridle batten across the corresponding batten on the other wing The height in inches of this thread above top surface of the keel should be at least Model Batten no 5 Batten no 6 Batten no 7 F3 145 9 3 4 inches 5 3 8 inches F3 170 10 1 2 inches 6 inches d F3 195 11 inches 6 3 4 inches F3 Tandem 16 inches 14 3 8 inches 10 inches Falcon 4 145 9 1 inches 4 8 inches Falcon 4 170 10 6 inches 6 inches Falcon 4 195 15 8 inches 10 1 inches Adjustment of the bridles requires replacing the bridle pigtail with one of a shorter to tighten or longer to loosen length or placing tubular shims under the sail to shorten individual bridle lines Improper adjustment of the bridles will affect the glider s pitch stability and flight characteristics in the following ways Bridles too loose If the bridles are adjusted too loose it will not affect the glider in normal flight as the bridles are always slack in this range anyway At angles of attack below normal flight there will be a reduction in pitch stability proportional to the amount by which the bridles are looser than they are supposed to be This stability reduction could increase the probability of a turbulence induced tumble or other in flight stability related loss of control Bridles too tight If the bridles are adjusted too tight it will
94. stream Control Bar may have changed since the glider was produced so it is necessary to specify this information when ordering these parts Glider Owner s Manual Addendum Falcon 3 4 Sport 2 and U2 We have introduced a new bolt nut and nut cap assembly configuration for the crossbar leading edge junction on Falcon 3 s and Falcon 4 s Sport 2 s and U2 s and for the separate crossbar side wire junction on Sport 2 s and U2 s The photos below show an example of the new assembly as installed on the Falcon 3 Tandem In each assembly a 1 4 inch clinch nut 10N 1740 is used in combination with a long enough bolt to provide several threads exposed beyond the nut and then the nylon nut cap is threaded onto the end of the bolt Installation of clinch nut Nylon nut cap installed above clinch nut The nylon nut cap pictured is item 15A 2010 NYLON THREADED NUT CAP 1 4 28 The nylon nut cap serves as a wear protector and also in effect provides a visual check that the nut is adequately engaged on the bolt because the nut cap can only engage if there are threads on the bolt extending beyond the nut Note Although the nylon nut cap has the appearance of an acorn nut it is not a struc tural part and must not be used as a fastener in any application The original assembly configuration for all of these assemblies included a bolt castle nut and small safety ring A later interim configuration used a clinch nut and safety ring The
95. structural failures both as a result of turbulence and as a result of various maneuvers outside the placarded operating limitations including but not necessarily limited to aerobatics We do not know and cannot know the full range of maneuvers or conditions which may cause the pilot s safety to be compromised nor can we test the glider in all possible circumstances A Note About Platform Towing When platform towing it is necessary to attach a nose line to the front of the glider to restrain the glider at the proper pitch attitude while on the tow platform If the noseline is installed improperly it is possible for it to cause the bottom front wires to become detached from the nose of the glider as the glider departs the platform during launch which will result in a complete loss of control of the glider and a very dangerous crash Please see the diagrams below for the correct way and one incorrect way to install the nose line Correct Attachment Incorrect Attachment Unsafe When routed incorrectly the nose line is simultaneously pulling down on the keel and forward on the front wires and or tang which is exactly what is required to disengage the tang from the keyhole collar In addition because the nose line also normally pulls forward from the nose of the glider it will normally restrain the front wires in approximately the normal position until tension on the nose line 1s released upon launch from the platform As a result
96. t sail plug clockwise twisting the sail up at the trailing edge or both Twist counter clockwise on either or both plugs to correct a right turn To rotate the sail plug use the allen wrench provided in your spare parts kit to loosen the allen screw thus pushing the wedge forward and releasing the plug If you loosen the screw too much the wedge will fall off the end of the screw inside the leading edge and you will have to dismount the sail to retrieve it Start by loosening the screw ten turns and then check to see if you can rotate it If not loosen it one turn at a time until it can be rotated After rotating the plug in the desired amount in the desired direction see above tighten the screw to secure the plug against rotation When the screw is properly tightened there will be a slight bulge less than the wall thickness of the tube in the rear leading edge tube adjacent to the screw Adjusting batten tension The number one and number two tip battens on the Falcon 3 are tensioned by looping the batten string over the notched end of the batten twice The remainder of the battens are tensioned by the adjust ment of the lever tip The inboard battens should be fairly loose as described in the batten installation portion of the set up procedure The outboard battens should be progressively more firm The number one batten strings should be fairly snug but not so tight as to slacken the sail mount webbing which mounts the sail
97. tability and structural characteristics required by the certification standards An owner s manual is required to be delivered with each HGMA certified glider and it is required that it contain additional airworthiness informa tion Weight of glider with all essential parts and without coverbags and nonessential parts 45 Ibs Leading Edge Dimensions a Nose plate anchor hole to 1 Crossbar attachment hole 109 5 2 Rear sail attachment point 195 5 196 25 b Outside diameter at 1 Nose 2 05 2 Crossbar ane C Rear sail attachment point 1 9 7 Crossbar Dimensions a Overall pin to pin length from leading edge attachment point to hinge bolt at glider centerline 96 37 b Largest outside diameter 2 05 Keel dimensions least and greatest allowable distances whether variable through tuning or through in flight variable geometry from the line joining the leading edge nose bolts to a he xbar center load bearing pin 42 75 25 b The pilot hang loop 59 5 1 5 Sail Dimensions a Chord lengths at 1 3 ft outboard of centerline 77 6 2 3 ft inboard of tip 46 0 D Span extreme tip to tip 394 2 Location of Information Placard Keel Location of lest Fly Sticker Kee Recommended Pilot Weight Range 120 190 Recommended Pilot Proficiency USHGA Novice HGMA COMPLIANCE VERIFICATION SPECIFICATION SHEET GLIDER MODEL Falcon 3 1 0 MANUFACTURED BY Wills Wing Inc All dimensions in inches weights in pounds NOTE These specifications
98. take extra care to pad your glider internally when you pack it up One spe cial area to pay attention to 1s the forward area of the glider where the crossbar center section bears against the top of the leading edge tubes and the kingpost sits on top of the keel Some extra padding inserted m this area will save wear on your airframe and sail In Closing With proper care and maintenance your glider will retain a high level of airworthiness for some years Because of the relatively short history of hang gliding and the rapid advances in new designs we do not have a lot of information about the ultimate service life of a hang glider We do know that ultraviolet UV damage to the sail from sunlight is probably the limiting factor in the life of your sail Try to avoid exposing your sail to sunlight any time you are not actually flying it We also know that there are forces in nature which can be so violent that they can result in fatal accidents regardless of the airworthiness of your aircraft Ultimately your safety 1s your responsibil ity Know the limitations of your knowledge skill and experience and know the limitations of your aircraft Fly within those limitations Have fun See you in the sky Wills Wing Inc 53 HGMA COMPLIANCE VERIFICATION SPECIFICATION SHEET GLIDER MODEL Falcon 4 145 MANUFACTURED BY Wills Wing Inc All dimensions in inches weights in pounds NOTE These specifications are intended only as a
99. the control bar apex using the bolts and nuts provided on the downtubes Note that on the right downtube the provided nylon washer goes in front of the control bar elbow 3 Install the bottom front and bottom rear wires into the respective downtubes as follows a b c d Remove the safety ring and clevis pin and remove the bottom plug from the bottom of the downtube Taking care not to induce any twisting in the wires and maintaining the proper orienta tion of the bottom front wire nose tang insert the bottom front and bottom rear wires into the back and front slots on the downtube and pass them out through the bottom of the downtube Remove the small aluminum spacer from the downtube plug and position the wires in the hollowed area in the bottom of the plug such that they are captured by the spacer when you re insert it While sliding the excess wire back out through the slots in the downtube re install the plug in the bottom of the downtube and secure it with the clevis pin and safety ring 4 Attach the bottom side wires to the downtubes as follows a b c Remove the knurled bushing from the bottom downtube plug taking care not to lose the nylon washer Install the bottom side wire tang and nylon washer into the space between the ears on the downtube bottom plug taking care that the nylon washer is forward of the side wire tang that the side wire tang 1s oriented with the small projection o
100. to tip 358 5 6 Location of Information Placard Kee Location of Test Fly Sticker Kee 7 Recommended Pilot Weight Range 140 220 8 Recommended Pilot Proficiency USHGA Novice 5 HGMA COMPLIANCE VERIFICATION SPECIFICATION SHEET GLIDER MODEL Falcon 9 195 MANUFACTURED BY Wills Wing Inc All dimensions in inches weights in pounds NOTE These specifications are intended only as a guideline for determining whether a given glider is a certified model and whether it is in the certified configuration Be aware however that no set of specifications however detailed can guarantee the ability to determine whether a glider is the same model or is in the same configuration as was certified or has those performance stability and structural characteristics required by the certification standards An owner s manual is required to be delivered with each HGMA certified glider and it is required that it contain additional airworthiness informa tion Weight of glider with all essential parts and without coverbags and nonessential parts 53 Ibs Leading Edge Dimensions a Nose plate anchor hole to l Crossbar attachment hole 133 2 Rear sail attachment point 228 5 229 25 b Qutside diameter at 1 Nose ZU 2 Crossbar 2 05 3 Rear sail attachment point 1 9 7 Crossbar Dimensions a Overall pin to pin length from leading edge attachment point to hinge bolt at glider centerline 11725 p Largest outside diameter 2 44 Keel dimensions
101. ttom side wire with about 75 lbs of force This is a rough field test of the structural security of the side wire loop the control bar the kingpost and the crossbar and will likely reveal a major structural defect that could cause an in flight failure in normal operation Check that the mid crossbar clevis pin and safety ring are installed At the left wingtip Check the proper installation of the number one batten and the sail mount webbing Check the proper installation of the washout tip and the proper position of the transverse batten Along the trailing edge left wing Check that there are no tears in the sail material along the trailing edge Check that all lever batten tips are properly engaged in the trailing edge hem and snapped into the locked position and that the batten strings on the number one and number two battens are properly secured Check that the bridles are properly engaged with the plastic retainer balls fully seated against the grommet E y d From the rear keel Check the nut on the top of the kingpost base bracket which secures the bracket to the keel Check the 1 4 solid rivet under the webbing sock at the base of the kingpost that secures the kingpost to the bracket Check the condition of the sweep wires in the vicinity of the kingpost base bracket Check the kingpost top for proper attachment and routing of the bridles and condition of the top rear wire and bridle pigtail wire Che
102. y Cycle Operations Gliders which are used in a training environment or in any situation which involves a high number of flight operations over short period of time will require an accelerated maintenance program in order to maintain adequate airworthiness The design and testing of these gliders does not necessarily take into account the types of wear which may result from high duty cycle operations The operator must take responsibility to thoroughly and adequately inspect the glider to determine whether maintenance is being conducted on a schedule appropriate to maintain the airworthiness of the glider A Note About Parts Replacement and Parts Interchangeability Falcon 1 s Falcon 2 s Falcon 3 s and Falcon 4 s share a number of parts but many parts are different In addition there are configuration variations within a given model line When ordering replacement parts 1t is very important to provide the glider serial number to insure that the correct replacement parts are provided The serial number 1s a five digit number beginning with the number 2 and can normally be found in three places on the glider written inside the nose of the sail most reliable on an adhesive label on the bottom of the keel at the nose and written on the operating limitations plac ard on the bottom of the rear of the keel Please also note that some configuration options such as basetube type straight vs speedbar or 095 wall vs 065 wall or optional Lite
103. y to prevent damage to the sail Falcon Set Up Procedure The Falcon has been specially designed to set up quickly and easily either on the control bar or flat on the ground We will first cover the steps for setting up on the control bar 1 With the glider in the bag lay the glider on the ground zipper up with the nose into the wind If there is more than five mph of wind or if the wind 1s gusty turn the glider slightly more than 90 degrees to the wind direction 2 Undo the zipper remove the battens and remove the control bar bag 3 Separate the control bar legs a Remove the safety ring speed nut and bolt from the corner bracket b Insert the basetube into the corner bracket so that the holes line up c Install the bolt nut and safety securing the bracket to the basetube Make sure that the bolt passes through both the bracket and the basetube thus securing the basetube to the bracket Proper orientation of the basetube during installation will result in the Wills Wing sticker being on top of the basetube and right side up when viewed while hooked into the glider in the normal flying position Do not insert the basetube into the fitting at an angle and do not force the fitting onto the base tube if it does not slide on freely Check for dirt or damage to the inside of the fitting or the out side of the basetube If the fitting 1s forced onto the basetube it may be impossible to remove See your dealer if the fitting

Download Pdf Manuals

image

Related Search

Related Contents

オーバー ドア  Trust Nium HD 720p Webcam  gazette n°57 - Foyers Ruraux du Centre : Accueil  Télécharger - Les Maux De Dos    Pioneer SE-MJ721  ENGLISH User's Guide  Sistema de Áudio com Toca-Discos e Tecnologia Bluetooth    

Copyright © All rights reserved.
Failed to retrieve file