Manual Change - Agilent Technologies
Contents
1. 9102002 Figure 2 2 16008B in an Environmental Test Oven Warning Use globes when handling the 16008B just after it comes out of a test 7 oven or wait until it has cooled down enough to not cause burns Exchanging the Electrode The 16008B has two optional electrodes in addition to the furnished 50 mm electrode You can exchange the electrode as required for your measurement To exchange the electrode do the following 2 4 Preparation for Use Main Electrode Screw X 3 e Y AX Co e Guard Electrode Wu T 7 m O __ ORS O 4 1 Figure 2 3 Exchanging the Electrode A9102001 Warning Do NOT touch the electrode and UNKNOWN connector while the High Voltage indicator is lit which shows the 4339B s output is a high voltage of up to 1000 Vdc maximum You must operate after turning off the voltage source output and you have confirmed the high voltage indicator is turned off To Change Electrodes 1 Turn the main electrode counter clockwise to loosen it and then remove it 2 Remove the three screws holding the Guard electrode in place 3 Remove the Guard electrode 4 Place the new Guard electrode so that the three holes are aligned with the three holes in the socket module 5 Insert and Tighten the three screws 6 Insert the new Main electrode and turn it clockwise to tighten it2. auim 3019 49719 piqes uid g yowa AD ova UND a a 2p0 1399 3 UEN waATIS yoya ZAND xovg uas sy uceinBy ay ees yams aM 9089 80091 N d avus youmg Aejoy 2po01399 3 U93IAS leJO Y 9105005 f 160088 Figure 4 5 Cable Connection o 4 13 Service Table 4 8 Replaceable Parts for the Cable Assembly Main Body Volume Surface 7 Selector Box 10mm 7 410 E 2 xt Ln gt lt n Smm 120 10mm 905 10mm 430 40mm 340 50mm P TI d N 3 4 p 5 7 Reference Agilent Part Designator Number Qty Description 1 16008 61661 1 Cable Assembly 2 0890 1649 115em Tube Flex 3 16008 61651 1 Cable Assembly Triaxial 4 16008 61654 1 Cable Assembly Black Label 5 16008 61655 1 Cable Assembly White Label 6 16008 61656 1 Cable Assembly Black Label 7 16008 61657 1 Cable Assembly White Label 8 04
3. Reference Agilent Part Designator Number Qty Description 1 16008 60072 1 Top Cover 2 0370 3231 1 Knob 3 0515 0914 8 Screw Flat M3L6 4 16008 25073 2 Bushing 5 16008 00171 1 Chassis 6 16008 24074 1 Bushing 7 16008 00172 1 Chassis Side 8 16008 00173 1 Chassis Side 9 16008 25074 5 Bushing 10 16008 60074 1 Terminal Assembly 11 0403 0316 4 Bumper Foot 12 1390 0896 2 Latch 13 0515 1550 4 Screw Pan M3L8 4 16 Service Table 4 10 Replaceable Parts for Upper Electrode 2 of 2 9105002 Reference Agilent Part Designator Number Qty Description 1 16008 61671 1 Cable 2 0515 0919 4 Screw Pan M3L25 3 2190 0584 4 Spring Washer 4 3050 0891 7 Washer 5 16008 24076 4 Spacer 6 16008 25071 2 Beam fi 16008 20071 1 Electrode 8 16008 00671 1 Plate 9 16008 60075 4 Guide Pin 10 0515 1550 4 Screw Pan M3L8 11 0515 0907 2 Screw Flat M3L6 12 16008 00672 1 Plate 13 16008 60073 1 Spring Assembly Service 4 17 Assembly Replacement Lower Electrodes This section explains the disassembly procedure and lists the replaceable parts for the lower electrodes Disassembly Procedure See Exchanging the Electrode in Chapter 2 when disassembling the lower electrode Replaceable Parts The kinds of electrodes and part numbers for each are shown in Table 4 11 The parts listed can be ordered from your nearest Agilent Technologies Office Ordering info
4. 4 14 4 9 Replaceable Parts for Upper Electrode 1012 4 16 4 10 Replaceable Parts for Upper Electrode 2 of 2 4 17 4 11 Replaceable Parts for Lower Electrodes 000084 4 19 4 12 6 pin cable connections 4 ll ll 2 4 4 22 Contents 3 General Information Introduction The purpose of this manual is to enable you to use your 16008B Resistivity Cell efficiently and confidently This manual contains both general and specific information To use the 16008B to perform a specific function without having to read the entire manual follow the directions in Using the 16008B Using the 16008B The 16008B has been designed to operate specifically with the 4339B High Resistance Meter m To install the 16008B turn to Chapter 2 m To operate the 16008B turn to Chapter 3 m To order replaceable parts for the 16008B turn to Chapter 4 Product Description The 16008B has been designed to operate specifically with the 4339B High Resistance Meter The 16008B is used to measure the volume or surface resistance resistivity of insulation materials The 16008B has the following features m Llectrode size selectable Three different size electrodes to meet your DUT size requirements and to meet to electrode size requirements required by different standards m Can be used in 30 C to 100 C ambient environments m Arbitrary contact pressure
5. 3 isn t included in the above picture 4 2 Service Assembly Replacement Main Body This section explains complex and important points when disassembling and assembling the Main Body The replaceable Parts List for the main body is also provided in this section How to start disassembling the main body Open the box from the top when replacing the electrodes and parts around the electrodes Open the box from the bottom when repairing the electrical connections The following describes how to open the box from the top 1 Remove both the main electrode and the guard electrode shown in Exchanging the Electrode in Chapter 2 2 Remove the black plate by removing the two screws marked with 3 Remove the black insulator by removing the three screws marked with Figure 4 1 Main Body Disassembly Top Cover Removal Before removing the top cover the screw which pushes the micro switch closed should be removed from the top cover This screw is accessed by removing the bottom cover it is mounted on the portion of the top cover which extends down into the box Micro Switch Adjustment When the top cover or the micro switch is reassembled the length of the screw which pushes the micro switch P N 16008 24051 closed must be adjusted so that it will cause the micro switch to open at the proper top cover opening angle 1 Put a drop of Lock Tite P N 0470 0013 on the screw s threads 2 Rotate the screw c
6. 800 810 0189 fax 800 820 2816 Europe tel 31 20 547 2323 fax 31 20 547 2390 Japan Call Center tel 0120 421 345 tel 81 426 56 7832 fax 81 426 56 7840 Korea tel 82 2 2004 5004 fax 82 2 2004 5115 Latin America tel 305 269 7500 fax 305 269 7599 Taiwan tel 0800 047 866 fax 0800 286 331 Australia New Zealand tel 61 3 9210 5555 Australia fax 61 3 9210 5899 tel 64 4 939 0636 New Zealand fax 64 4 972 5364 Asia Pacific tel 65 6375 8100 fax 65 6836 0252 Email tm_asia agilent com
7. 4 Screw Pan M3L8 7 16008 01254 1 Angle Bracket 8 1460 2238 4 Spring 9 16008 25055 4 Bushing 10 16008 25053 4 Spacer 11 16008 01257 1 Angle Bracket 12 16008 01255 1 Angle Bracket 13 16008 25054 1 Insulator 14 0360 2066 1 Contact Assembly 15 0360 2082 1 Connection signal Contact 16 16008 25084 1 Insulator 4 10 Service Assembly Replacement Volume Surface Selector Box This section explains about the replaceable parts for the volume surface selector box Replaceable Parts Table 4 7 shows the replaceable parts for the Volume Surface Selector Box See also Assembly Replacement Cable Assembly for the cable connections The parts listed can be ordered from your nearest Agilent Technologies Office Ordering information must include the Agilent part number and the quantity required Table 4 7 Replaceable Parts for Volume Surface Selector Box O Reference Agilent Part Designator Number Qty Description 1 3100 3505 1 Switch Rotary 2 16008 01263 1 Angle Bracket 3 0400 0276 1 Grommet 4 1400 1653 7 Cable Tie 5 0400 0010 2 Grommet 6 0411 0306 1 Grommet 7 0515 2079 1 Screw Pan M4L8 1400 0054 1 Clamp Cable 8 16008 04065 1 Top Cover 9 0370 2994 1 Knob 10 0515 0914 5 Screw Flat M3L6 11 16008 60062 1 Bottom Cover 12 16008 01264 1 Angle Bottom 13 0515 0914 2 Screw Flat M3L6 1 Includes a nut and washers Service Assembly Replacement Cable Assembly This section
8. 7 Confirm that the top of the Guard electrode sets higher than the top of the Main electrode Caution You must handle the DUT contact of Guard electrode carefully because it is made from a soft material and is easily scratched Preparation for Use 2 5 Connecting the Adapter for Use Connect the 16008B to the 4339B as shown in Figure 2 4 You must connect BNC triaxial and interlock connectors If the interlock connector is not connected the 4339B will not output the source voltage Warning Do NOT touch the electrode and UNKNOWN connector while the High Voltage indicator is lit which shows the 4339B s output is a high voltage of up to 1000 Vdc maximum You must operate after turning off the voltage source output and you have confirmed the high voltage indicator is turned off iaaloooQ 15006003 Figure 2 4 Connecting the Adapter Repackaging the Adapter If shipment to a Agilent Technologies service center is required each adapter should be repackaged using the original factory packaging materials Alteratively comparable packaging materials may be used Wrap the adapter in heavy paper and pack in anti static plastic packing material Use sufficient shock absorbing material on all sides of the 16008B to provide a thick
9. Part Number Quantity 16 mm main electrode 16008 60085 1 88 mm guard electrode 16008 24086 1 spare screw 0515 0907 3 carrying case 16008 60181 1 Ambient Environmental Considerations Operating and Storage The 16008B must be operated within an ambient temperature range of 30 C to 100 and relative humidity up to 70 RH at 40 C non condensing The 16008B may be stored within a temperature range of 40 C to 70 and at a relative humidity up to 95 at 40 C non condensing Using the 16008B in an Environmental Test Oven The 16008B has the capability for high temperature measurement in environmental testing up to 100 C This section provides information for using the 16008B in an environmental test chamber Note If the environmental test oven temperature exceeds 100 C the basic specifications will be invalid You must pay close attention to temperature Y settings Preparation for Use 2 3 The Volume Surface selector box must be located outside of the oven because it is not designed for operating at temperatures up to 100 C see Specifications in Chapter 1 To locate the box outside of the oven the 4100 mm hole is required in the oven Figure 2 2 shows the measurement configuration when using the 4339B in an environmental test oven galpooo 0000
10. explains about the replaceable parts for the cable assembly Do NOT forget Cable Tie Caution When reassembling cables do NOT forget to tighten the cable ties Cable ties shown in Figure 4 3 are used to fix the cables in the fixture assemblies and i should NOT be forgot in any time CABLE TIE Main Body Bottom View Volume Surface Selector Box Top View 9105013 Figure 4 3 Do NOT forget the Cable ties High Voltage Consideration The cables shown in Figure 4 4 have an approximately 1000 V voltage inside of the cable Do not put this cable less than 8 mm close to any conductive device Volume Surface Selector Box Bottom View 9105012 Figure 4 4 High Voltage Consideration Replaceable Parts Table 4 8 shows the replaceable parts for the cable assembly Figure 4 5 shows the connection of these cables The parts listed parts can be ordered from your nearest Agilent Technologies Office Ordering information must include the Agilent part number and the quantity required 4 12 Service xog 6 e2ejins euinjoA ava wwo LANS e a 0210 0680 N S aqn3 Bununys 3e9y ow Aq SI Julod uono oeuuoo JEU smoys pog TVIXVIMHL ANSANS ALIHM
11. 00 0276 2 Grommet 9 1400 1653 5 Cable Tie 10 16008 25061 2 Insulator 11 0400 0306 1 Grommet 12 16008 68061 3 Jumper Wire 13 16008 61652 1 Cable Assembly BNC 14 16008 61653 1 Cable Assembly 6 pin 1 Includes a flexible tube Item 2 and 5 cables Item 3 through 7 2 Inside of the flex tube 3 Put Grommet on before inserting into the flex tube 4 14 Service Assembly Replacement Upper Electrode This section explains disassembly procedure and lists the replaceable parts for the upper electrode Upper Electrode Disassembly Figure 4 6 gives the disassemble procedure for the upper electrode 1 Remove the knob on the top of the box marked with D 2 Remove two screws marked with on the side of the cover 3 Remove the cover by pushing the latches on both sides marked with 3 4 Remove the 4 screws on both sides of the electrode Now the upper electrode assembly will separate into 2 parts Figure 4 6 Upper Electrode Disassembly Replaceable Parts Table 4 9 and Table 4 10 shows and lists the replaceable parts for the upper electrode The parts listed can be ordered from your nearest Agilent Technologies Office Ordering information must include the Agilent part number and the quantity required Service 4 15 Table 4 9 Replaceable Parts for Upper Electrode 1 of 2
12. 008 60055 1 Spring Unit Assembly 5 16008 40051 1 Trim Personal 6 16008 60087 1 Contact Assembly 7 16008 00153 1 Chassis 8 16008 00651 1 Plate 9 16008 25081 1 Insulator 0515 1550 4 Screw Flat M3L8 3050 0891 4 Washer 10 16008 00252 1 Panel 0515 0914 1 Screw Flat M3L6 1 See Contact Assembly for details Service 4 5 Table 4 4 Replaceable Parts for Main Body Bottom View Reference Agilent Part Designator Number Qty Description 1 16008 24051 1 Screw to push the microswitch 2 1 Microswitch 1 Switch Cover 3 16008 68051 1 Jumper Wire 4 16008 00151 1 Chassis 5 16008 00251 1 Panel Top 6 1400 0054 1 Clamp Cable 0515 2079 1 Screw Pan Head 7 16008 00153 1 Chassis 8 16008 60055 1 Spring Unit Assembly 9 1400 1653 6 Cable Tie 10 0515 0914 2 Screw Flat Head 11 16008 60054 1 Spring Unit Assembly 1 Includes nuts and bolts to mount the microswitch 4 6 Service Caution 1 Use the cable tie specified in the list because it is a special cable tie which Y can withstand high temperatures 2 When disassembling the top cover the screw which pushes the micro switch closed must be removed first See Top Cover Removal for details 3 When reassembling the top cover or the micro switch the screw which pushes the micro switch closed must be adjusted to let the micro switch open at the proper opening angle of the top cover See Micro Switch Adjustment for details Contact Assembly F
13. Agilent 16008B Bias RESISTIVELY CELL Operation and Service Manual Change 1 Manual Change Replace the Caution in 2 5 with the following sentences Caution Change 2 Agilent Part No NA August 2008 You must handle the DUT contact of Guard electrode carefully because it is made from a soft material and is easily scratched You must keep the flatness between the Main electrode and the Guard electrode In case of being uneven between the Main electrode and the Guard electrode the Main electrode may not connect with the DUT correctly Replace step 1 the Open Correction Procedure in 3 3 with the following sentences 1 Turn the load knob counterclockwise CCW until the distance between the upper electrode and the lower electrode is about 10mm Note If turning the load knob counterclockwise until the upper electrode does not move there is a risk that the cover is not close fitting enough Change 3 Replace the parts in the Replacement Parts with the following table Page Reference Designator Agilent Part Number Description 4 4 5 0403 0786 Bumper Foot 4 4 9 0403 0833 Bumper Foot 4 6 3 Delete 16008 68051 Jumper Wire 4 9 17 16008 25086 Insulator 4 10 1 16008 25052 Bushing 4 10 2 8710 2100 Probe Contact 4 10 16 16008 25056 Insulator 4 14 2 0890 2300 Tube Flex 4 16 11 0403 0833 Bumper Foot 4 19 8 16008 60191 Carrying Case O Copyright 2008 Agilent Technologi
14. any direct indirect special incidental or consequential damages whether based on contract tort or any other legal theory Assistance Product maintenance agreements and other customer assistance agreements are available for Agilent Technologies products If you need assistance contact your nearest Agilent Technologies Sales and Service Office Addresses are provided at the back of this manual Copyright 1992 1999 2000 Agilent Technologies Japan Ltd Manual Printing History The manual printing date and part number indicate its current edition The printing date changes when a new edition is printed Minor corrections and updates which are incorporated at reprint do not cause the date to change The manual part number changes when extensive technical changes are incorporated March 1992 First Edition part number 16008 90010 July 1999 occ nen nas Second Edition part number 16008 90011 March 2000 Third Edition part number 16008 90011 Safety Summary The following general safety precautions must be observed during all phases of operation service and repair of this instrument Failure to comply with these precautions or with specific WARNINGS elsewhere in this manual may impair the protection provided by the equipment In addition it violates safety standards of design manufacture and inte
15. atures are maintained Dangerous Procedure Warnings Warnings such as the example below precede POTENTIALLY DANGEROUS PROCEDURES throughout this manual Instructions contained in the warnings must be followed Warning Dangerous voltages capable of causing death are present in this instrument Use extreme caution when handling testing and adjusting this instrument Safety Symbols General definitions of safety symbols used on equipment or in manuals are listed below A O Warning Caution Y Note vi A Instruction manual symbol the product is marked with this symbol when it is necessary for the user to refer to the instruction manual Alternating current Direct current On Supply Off Supply This Warning sign denotes a hazard It calls attention to a procedure practice condition or the like which if not correctly performed or adhered to could result in injury or death to personnel This Caution sign denotes a hazard It calls attention to a procedure practice condition or the like which if not correctly performed or adhered to could result in damage to or destruction of part or all of the product Note denotes important information It calls attention to a procedure practice condition or the like which is essential to highlight Affixed to product containing static sensitive devices use anti static handling procedures to prevent electrostatic discharge damage t
16. can be applied on DUT General Information 1 1 Accessories Supplied The accessories listed in Table 1 1 are supplied with the 160086 Table 1 1 Furnished Accessories Description Part Number Quantity Operation and Service Manual P N 16008 90010 1 Options The following options are supplied for the 16008B Table 1 2 Supplied Options Product Number Description 16008B Option 001 Add 26 76 mm diameter electrodes with carrying case Option 002 Add 26 mm diameter electrode with carrying case Option 003 Add 76 mm diameter electrode with carrying case Operating and Safety Precautions Service The voltage levels up to 1000 V in this adapter warrants extreme care for operator safety Service must be performed only by qualified personnel Specifications This section lists the complete 16008B specifications These specifications are the performance standards and limits against which the 16008 is tested When shipped from the factory the 16008B meets the following listed specifications Measurement Parameter Volume Resistance Resistivity Surface Resistance Resistivity Applicable Test Voltage oooooocococccconcccco 1000 V maximum Applicable Test Current cece e eee 10 mA maximum Applicable Instrument he e 4339B Interlock Circuito furnished Operating Tempe
17. ctrode 2 0 2 5 2 4 Connecting the Adapter ll ll An 2 6 3 1 External Appearance 2 2 ll ll 4 4 es 3 1 3 2 Electrode Appearance s 4 e 20 8 2 3 8 Load Scale 2 252 2 2 2525 25252252 2 52 2 2522D52 5 3 3 3 4 Latch 2 2 2 0 404 4 ss 3 5 4 1 Main Body Disassembly 2 2 4 3 4 2 Parts Identification for Contact Assembly 2 4 8 4 3 Do NOT forget the Cable ties ll eA 4 12 4 4 High Voltage Consideration lll llle 4 12 4 5 Cable Connection of 160088 a a a a n 4 13 4 6 Upper Electrode Disassembly e 4 15 4 7 Schematic Diagram of 16008B l l 4 20 4 8 Cable Connection Check l l ll ll 4 4 21 Tables 1 1 Furnished Accessories 2 2 204 2 4 4 aA 1 2 1 2 Supplied Options 1 2 2 1 Contents 2 2 4 1 Replaceable Parts Overview e 4 2 4 2 Replaceable Parts for Main Body External View 4 4 4 3 Replaceable Parts for Main Body Top View 2 D 4 5 4 4 Replaceable Parts for Main Body Bottom View 4 6 4 5 Replaceable Parts for Contact Assembly MM 4 9 4 6 Replaceable Parts for Spring Unit a a a a a 4 10 4 7 Replaceable Parts for Volume Surface Selector Box lcs 4 11 4 8 Replaceable Parts for the Cable Assembly
18. echnologies from another country Agilent Technologies warrants that its software and firmware designed by Agilent Technologies for use with an instrument will execute its programming instruction when property installed on that instrument Agilent Technologies does not warrant that the operation of the instrument or software or firmware will be uninterrupted or error free Limitation of Warranty The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance by the Buyer Buyer supplied software or interfacing unauthorized modification or misuse operation outside of the environmental specifications for the product or improper site preparation or maintenance No other warranty is expressed or implied Agilent Technologies specifically disclaims the implied warranties of merchantability and fitness for a particular purpose Certification The Agilent Technologies certifies that this product met its published specifications at the time of shipment from the factory Agilent Technologies further certifies that its calibration measurements are traceable to the United States National Institute of Standards and Technology to the extent allowed by the Institute s calibration facility or to the calibration facilities of other International Standards Organization members Exclusive Remedies The remedies provided herein are the buyer s sole and exclusive remedies Agilent Technologies shall not be liable for
19. es E Agilent Technologies Agilent 16008B Resistivity Cell Operation and Service Manual eto efe Agilent Technologies Agilent Part No 16008 90011 Printed in JAPAN March 2000 Third Edition Notice The information contained in this document is subject to change without notice This document contains proprietary information which is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated to another language without the prior written consent of the Agilent Technologies Agilent Technologies Japan Ltd Component Test PGU Kobe 1 3 2 Murotani Nishi ku Kobe shi Hyogo 651 2241 Japan Warranty This Agilent Technologies instrument product is warranted against defects in material and workmanship for a period of one year from the date of shipment except that in the case of certain components listed in this manual the warranty shall be for the specified period During the warranty period Agilent Technologies will at its option either repair or replace products which prove to be defective For warranty service or repair this product must be returned to a service facility designed by Agilent Technologies The Buyer shall prepay shipping charges to Agilent Technologies and Agilent Technologies shall pay shipping charges to return the product to the Buyer However the Buyer shall pay all shipping charges duties and taxes for products returned to Agilent T
20. espectively When the top cover is opened the source voltage is turned OFF inside the 4339B side A9103005 10 11 12 3 2 Figure 3 2 Electrode Appearance Main electrode covered with a conductive elastomer The negative test voltage is applied from the Output terminal of the 4889 Guard electrode Provides the guard for Volume measurements Applies the positive test voltage for surface measurements Upper electrode Provides the guard for surface measurements Applies the positive test voltage for volume measurements Load scale This scale shows currently applied pressure in kirograms Load knob apply load for the DUT turn this knob to clockwise Operation OPEN Correction OPEN correction compensates cancels residual resistance for resistance measurements Warning Do NOT touch the electrodes and UNKNOWN connector while the High Voltage indicator is lit which shows the 4339B s output is a high voltage of up to 1000 Vdc maximum You must operate after turning off the voltage source output and you have confirmed the high voltage indicator is turned off OPEN Correction Procedure DO NN Turn the load knob counterclockwise ccw until the upper electrode does not move Select the current measurement mode at the 4339B Close the top cover Apply the source voltage required for your meas
21. fety Considerations 4 a 4 4 4 44 es 4 1 Assembly Replacement General Information 4 1 Assembly Replacement Main 4 3 How to start disassembling the main body cll 4 8 Top Cover Removal 2 2 2 2525 22 2 252522D522525225 4 8 Micro Switch Adjustment 4 8 Replaceable Parts ll 4 le s 4 4 Contact Assembly 2 2 242 252 225 252522 5252 2D 525 4 1 Spring Unit 2 4 2 ll 2 2 s 4 10 Assembly Replacement Volume Surface Selector Box 4 11 Replaceable Parts ll 4 le s 4 11 Assembly Replacement Cable Assembly 4 12 Do NOT forget Cable Tie 4 12 High Voltage Consideration lll 4 12 Contents 1 Replaceable Parts Assembly Replacement Upper Electrode cll rn Upper Electrode Disassembly se eee n Replaceable Parts Assembly Replacement Lower Electrodes Disassembly Procedure Replaceable ll ll e n Troubleshooting 2 2 ll s s es Schematic Diagram 2 2 ll 4l 4 4e Cable Connection Check BNC Cable and Triaxial Cable Connection Check Interlock Circuit Connection Check MM Contents 2 Figures 2 1 Product Overview 2 2 2 2 16008B in an Environmental Test Oven 42430 2 4 2 8 Exchanging the Ele
22. firm cushion and to prevent movement Seal the shipping container securely and mark it FRAGILE 2 8 Preparation for Use Operation Introduction This chapter describes the features of the 16008B and connections to the 4339B and the DUT A9103001 Figure 3 1 External Appearance 1 Handle 2 Top cover This shields against external electrical noise and provides an interlock to enable and disable the test voltage when CLOSED and OPEN respectively 3 Volume Surface selector Used to select the volume or surface measurement mode A displayed resistivity parameter would be changed automatically interlocking with selector change When you operate in manual or external trigger mode displayed parameter will not change until the 4339B has triggered Operation 3 1 Note When you change Volume and Surface mode turn off the source voltage output of the 4339B 4 5 Volume Surface selector box BNC connector This connector supplies the source voltage to the 16008B This is a high voltage BNC connector and is not compatible with standard BNC connectors Triaxial connector The measured signal is carried on the center conductor of this connector Interlock connector This connector enables the interlock function which enables and disables application of the source voltage from the 4339B when the top cover is closed and opened r
23. igure 4 2 and Table 4 5 show the replaceable parts for the contact assembly in the main body Service 4 7 Y aa Figure 4 2 Parts Identification for Contact Assembly ervice Table 4 5 Replaceable Parts for Contact Assembly Reference Agilent Part Designator Number Qty Description 1 16008 60081 1 Main Electrode 50mm 2 0515 0907 3 Screw Flat M3L8 3 16008 24082 1 Guard Electrode 4 0515 1550 4 Screw Pan M3L8 5 3050 0891 3 Washer 6 16008 25081 1 Insulator 7 1460 0323 4 Spring 8 0515 1550 3 Screw Pan M3L8 9 3050 0891 3 Washer 10 16147 25001 3 Insulator 11 16008 60087 1 Contact Assembly 12 16008 00651 1 Plate 13 0515 1076 3 Screw Flat Head 14 0360 2066 1 Contact Pin 15 16008 25085 1 Spacer 16 0360 2082 1 Contact signal Contact 17 16008 25084 1 Insulator 18 16008 00151 1 Chassis 1 Do not disassemble it further because a special tool is required to assemble it Caution Before disassembling the Contact Assembly remove the electrical connections at the bottom of box Service 4 9 Spring Unit Table 4 6 shows the spring unit in the main box Table 4 6 Replaceable Parts for Spring Unit 9105003 Ss 1 Reference Agilent Part Designator Number Qty Description 1 16008 25025 6 Bushing 2 8710 1951 1 Probe Contact 3 16008 24052 1 Terminal 4 16008 01256 1 Angle Bracket 5 0515 0914 2 Screw Flat M3L6 6 0515 1550
24. ime of at least one minute 3 4 Operation Removing the Upper Electrode Warning Do NOT touch the electrode and UNKNOWN connector while the High Voltage indicator is lit which shows the 4339B s output is a high voltage of up to 1000 Vdc maximum You must operate after turning off the voltage source output and you have confirmed the high voltage indicator is turned off To Remove Upper Electrode 1 Push the latch on both sides of the upper electrode See Figure 3 4 The lock will then be released 2 Lift the upper electrode up and remove it PUSH HERE Figure 3 4 Latch Note The upper electrode may not release when you push the latch and a contact i pressure load is still applied If this happens turn the contact pressure load Y knob CCW to decrease the applied pressure until the upper electrode releases Operation 3 5 Care of the Electrodes The electrodes should be kept clean to obtain complete contact with the DUT To clean the electrodes except for the conductive elastomer wipe them with a dust free cloth that has been dipped in alcohol To avoid scratching the guard electrode when the 16008B is not in use place the furnished acrylic plate between upper and guard electrodes and apply a pre load contact pressure to firmly hold the acrylic plate in place Warning Do NOT touch the electrode and UNKNOWN connector while the High Voltage indicator is lit which shows the 4339B s outpu
25. kness sssssssssssss IR n 10 um to 10 mm Electrode Size Main Electrode Guard Electrode Note 926 mm 998 mm option 50 mm 10 mm furnished 476 mm 88 mm option Operating Load e e 10 kgF maximum Dimensions 240 W x 180 H x 240 D mm Cable Length e ese e e e ea 1 20 body to Selector box nn e e e ee 0 82 m 1 After compensation measurement time is LONG 950 70 mm electrode 23 5 C 5096 RH 2 After 1000 V has been applied for 1 minute in no vibration and shock environment and under the same conditions as 1 3 Inside diameter General Information 1 3 Preparation for Use Introduction This chapter explains how to install the 16008B Resistivity Cell The topics covered include initial inspection ambient environmental considerations connecting the adapter for use and repackaging the adapter for shipping Initial Inspection The adapter has been carefully inspected electrically and mechanically before being shipped from the factory It should be in perfect physical condition no scratches dents or the like and it should be in perfect electrical condition Verify this by carefully performing an incoming inspection to check the adapter fo
26. lockwise until you hear the micro switch click closed or use the low resistance range of a multimeter and watch for the resistance change when the switch closes 3 Rotate the screw one more full turn clockwise Service 4 3 Replaceable Parts Table 4 2 through Table 4 4 show and list the replaceable parts for the main body The parts listed can be ordered from your nearest Agilent Technologies Office Ordering information must include the Agilent part number and the quantity required Table 4 2 Replaceable Parts for Main Body External View S Reference Agilent Part Designator Number Qty Description 1 16008 60052 1 Top Cover 2 16008 40051 1 Trim Personal 3 16008 60053 1 Bottom Cover 4 0515 0914 2 Screw Flat M3L6 5 0403 0712 4 Bumper Foot 0515 1551 4 Screw Pan M3L10 6 1440 0186 1 Handle 0515 2415 2 Screw M8L16 7 0400 0276 2 Grommet 8 16008 00251 1 Panel Top 9 0403 0316 2 Bumper Foot 10 16008 09051 1 Hinge 0515 0907 3 Screw Flat M3L8 0515 0914 3 Screw Flat M3L6 1 One machine screw P N 0515 0914 on this panel not included in the above picture 4 4 Service Table 4 3 Replaceable Parts for Main Body Top View Reference Agilent Part Designator Number Qty Description 1 16008 00151 1 Chassis 2 16008 60054 1 Spring Unit Assembly 3 16008 61657 1 Cable Assembly White Label 1400 1653 1 Cable Tie 1400 0054 1 Clamp Cable 0515 2079 1 Screw Pan M4L8 4 16
27. nded use of the instrument The Agilent Technologies assumes no liability for the customer s failure to comply with these requirements Note 16008B is designed for use in INSTALLATION CATEGORY I according to IEC i 61010 1 and POLLUTION DEGREE 1 according to IEC 61010 1 and IEC 60664 1 Y 16008B is an INDOOR USE product Do NOT operate in an Explosive Atmosphere Do not operate the instrument in the presence of flammable gasses or fumes Operation of any electrical instrument in such an environment constitutes a safety hazard Keep Away from Live Circuits Operating personnel must not remove instrument covers Component replacement and internal adjustments must be made only by qualified maintenance personnel Do not replace components with the power cable connected Under certain conditions dangerous voltages may exist even with the power cable removed To avoid injury always disconnect power and discharge circuits before touching them Do NOT Service or Adjust While Alone Do not attempt internal service or adjustment unless another person capable of turning off power and capable of rendering first aid and resuscitation is present Do NOT Substitute Parts or Modify Instrument Because of the danger of introducing additional hazards do not substitute parts or perform unauthorized modifications to the instrument Return the instrument to a Agilent Technologies Sales and Service Office for service and repair to ensure the safety fe
28. nnections between the connectors and the terminals as shown in Figure 4 8 BNC Upper Electrode Connector Surface Meas 5 Volume Meas TRIAXIAL Connector Main Electrode Guard Electrode Figure 4 8 Cable Connection Check Service 4 21 Interlock Circuit Connection Check Interlock connector connections and its pin locations are shown in Table 4 12 Check the connctions between each of the 6 pins and the outer conductor of BNC connector or the Triaxial connector Table 4 12 6 pin cable connections 1 6 9105007 Pin Top Cover Selector Number Open Close Volume Surface 1 NC GND lt 2 NC 3 GND lt 4 GND lt 5 GND NC 6 GND lt 1 means Not Connected 2 Touch the BNC outer conductor for GND 4 22 Service REGIONAL SALES AND SUPPORT OFFICES For more information about Agilent Technologies test and measurement products applications services and for a current sales office listing visit our web site http www agilent com find tmdir You can also contact one of the following centers and ask for a test and measurement sales representative 21 01 2004 United States Test and Measurement Call Center tel 1 800 452 4844 fax 1 888 900 8921 Canada Test and Measurement Call Center tel 1877 894 4414 fax 1 888 900 8921 China tel
29. o component Caution risk of electric shock Terminals which may be supplied from the interior of the equipment at a voltage exceeding 1 kV or allow connection to a voltage exceeding 1 kV are marked with this symbol Contents 1 General Information Introduction a a 2 4 o 4 1 1 Using the 1600BB_ 2 a 1 1 Product Description ll ll ll eh 1 1 Accessories Supplied a a eh 1 2 Options oaoa a a 1 2 Operating and Safety Precautions 1 2 Service 2 l l o 1 2 Specifications o 1 2 Supplemental Performance Characteristics MM 1 3 2 Preparation for Use Introduction 2 4 ll 4 4 4 4 44 a 2 1 Initial Inspection le e 44e 2 1 Ambient Environmental Considerations lll nn 2 8 Operating and Storage 2 3 Using the 16008B in an Environmental Test Oven 2 3 Exchanging the Electrode 4 445 2225 2 4 Connecting the Adapter for Use llle 2 6 Repackaging the Adapter 2 6 3 Operation Introduction 2 4 ll 4 4 4 4 44 a 9 1 OPEN Correction 3 3 Applying Contact Pressure 2 ll 4h 3 3 Operation 4 4A s 9 4 Removing the Upper Electrode 4 4 35 Care of the Electrodes a a a s 24 4 s 3 6 Checking Procedure 3 6 4 Service Introduction 2 2 aos 4 1 Sa
30. r signs of physical damage and missing contents If any discrepancy is found notify the carrier and Agilent Technologies Your Agilent Technologies sales office will arrange for repair and replacement without waiting for the claim to be settled 1 Inspect the shipping container for damage and keep the shipping materials until the incoming inspection is completed 2 Verify that the shipping container contains everything shown in Figure 2 1 and listed in Table 2 1 9 Inspect the exterior of the 16008B for any signs of damage Preparation for Use 2 1 Figure 2 1 Product Overview Table 2 1 Contents Description Agilent Part Number Quantity D Resistivity Cell 16008B 1 0 Plate 16008 1033 1 9 Operation and Service Manual 16008 90020 1 1 Operation and Service Manual is not shown in Figure 2 1 2 2 Preparation for Use When an option is ordered with the 16008B the following items are included Option 001 Option 002 Option 003 Description Agilent Part Number Quantity 226 mm main electrode 16008 60083 1 438 mm guard electrode 16008 24084 1 476 mm main electrode 16008 60085 1 88 mm guard electrode 16008 24086 1 spare screw 0515 0907 3 carrying case 16008 60181 1 Description Agilent Part Number Quantity 26 mm main electrode 16008 60083 1 38 mm guard electrode 16008 24084 1 spare screw 0515 0907 3 carrying case 16008 60181 1 Description Agilent
31. rature 30 to 100 C connector 0 to 55 C Operating Humidity n tenn as lt 70 RH 40 C Cable Length mmn 1 2 m connector to electrode Weight kg Non operating Temperature 40 to 70 C Non operating Humidity n ees lt 95 RH 40 C 1 2 General Information 1 The 4339B limits a maximum test current to 10 mA when using with the 16008B Maximum measurable current of the 4339B is 100 4A Supplemental Performance Characteristics This section gives supplemental performance characteristics Supplemental performance characteristics are not specifications but are typical characteristics included as additional information for the operator Supplemental performance characteristics are not guaranteed Resistivity Measurement Range Volume Resistivity up to 4 0 1075 Surface Resistivity 11000122 12217 up to 4 0x10 Q Leakage Current less than 1 0 pA Stability ooo less than 0 5 pA Applicable DUT Device Under Test Size 50 mm to 125 mm diameter Applicable DUT Thic
32. rmation must include the Agilent part number and the quantity required 4 18 Service Table 4 11 Replaceable Parts for Lower Electrodes Reference Agilent Part Designator Number Qty Description 1 16008 60081 1 Main Electrode 50mm 2 16008 24082 1 Guard Electrode 70mm 3 16008 60083 1 Main Electrode 26mm 4 16008 24084 1 Guard Electrode 38mm 5 16008 60085 1 Main Electrode 76mm 6 16008 24086 1 Guard Electrode 88mm 7 16008 60088 1 Spare Screws 8 16008 60181 1 Carrying Case 1 includes 3 screws 0515 0907 and a case 1540 0692 Service 4 19 Troubleshooting This section includes the schematic diagram of the 16008B and gives some troubleshooting hints Schematic Diagram Figure 4 7 is the schematic diagram of the 16008B i Upper Electrode BNC i High Voltage 57 6 pin Cable i Volume Meas Interlock Main Electrode Guard Electrode Main Body 9105001 Figure 4 7 Schematic Diagram of 160088 4 20 Service Cable Connection Check After repairing check the cable connections listed in Figure 4 8 and Table 4 12 using a multimeter which has a low resistance range 1 or 2 Q The information in these lists can be also used for troubleshooting of the 16008A BNC Cable and Triaxial Cable Connection Check Check the co
33. t is a high voltage of up to 1000 Vdc maximum You must operate after turning off the voltage source output and you have confirmed the high voltage indicator is turned off Checking Procedure The 16008B and the 4339B is operated with high voltage up to 1000 V These products are designed that the operator can measure safely To keep the safe condition you must execute following checking procedure periodically Warning Do NOT touch the electrode and UNKNOWN connector while the High Voltage indicator is lit which shows the 4339B s output is a high voltage of up to 1000 Vdc maximum You must operate after turning off the voltage source output and you have confirmed the high voltage indicator is turned off Daily Safety Verification Procedure 1 Connect the 16008B to the 4339B 2 Close the top cover of the 16008B 3 Set source voltage to 42 V 4 Press V output key of the 4339B Confirm that the V output indicator and the High Voltage indicator turn on 5 Open top cover of the 16008B Confirm that the High Voltage indicator turns off immediately 6 Close the top cover again Confirm that the High Voltage indicator still turns off If you encountered any errors in checking procedure contact your nearest Agilent Technologies Office 3 8 Operation Service Introduction This chapter covers the following subjects m Assembly Replacement o Disassembly Procedure for main assembly o Replaceable Par
34. ts m Troubleshooting Safety Considerations This manual contains CAUTIONs which must be followed to ensure the safety of the operator and to keep the instrument in a safe and serviceable condition Warning These servicing instructions are for use by qualified personnel only Do NOT perform any servicing other than that contained in the operating section unless you are qualified to do so Assembly Replacement General Information Table 4 1 shows all items included with the 16008B Detailed explanations for the following five parts are given in the sections which follow m Main Body m Volume Surface Selector Box m Cable Assembly m Upper Electrode m Lower Electrodes Service 4 1 Table 4 1 Replaceable Parts Overview Lon Reference Agilent Part Designator Number Qty Description 1 Not Assigned 1 Main body 2 Not Assigned 1 Cable Assembly 3 Not Assigned 1 Volume Surface Selector Box 4 16008 60051 1 Main Fixture Assembly 5 16008 60071 1 Upper Electrode Assembly 6 16008 1033 1 Plate 7 0515 0907 3 Screw Pan M3L8 for guard electrode 8 Not Assigned 1 Lower Electrodes 16008 90011 1 Operation and Service Manual 1 includes Items 1 through 3 2 See Assembly Replacement Lower Electrodes for each lower electrode
35. up to 1000 Vdc maximum You must operate after turning off the voltage source output and you have confirmed the high voltage indicator is turned off 1 Connect the Triaxial connector to the INPUT terminal the BNC connector to the OUTPUT terminal and the Interlock connector to the Interlock terminal of the 4339B 2 Select either a surface or a volume measurement using the Volume Surface selector Note Y Turn off the voltage output when you change the Volume Surface selector If you change the Volume Surface selector when voltage applied a calibration open correction or offset error cancel of the 4339A would be failed due to noise generated from the Volume Surface selector 3 Perform an OPEN correction as described in OPEN Correction 4 Place the DUT on the Main electrode and then place the upper electrode on the DUT 5 Turn the contact pressure load knob to adjust the electrode contact pressure on the DUT Refer to Applying Contact Pressure 6 Close the Top cover The 16008B measurement preparation is now complete 7 Follow the measurement instructions described in the 4339A Operating Manual to perform the measurement Caution Do NOT short the upper and lower electrodes when the voltage source is Y turned on Note For surface and volume measurements different voltage polarities are applied i to the DUT When changing between surface and volume measurements the 4339B requires a settling t
36. urement at the 4339B Set measurement time to LONG and wait until the current has stabled to within 0 5 pA Press keys of the 4339B to perform the OPEN correction Note When an OPEN correction is performed the electrodes must be separated i enough to prevent leakage current from occurring which will lead to OPEN Y correction instability Note Do NOT allow vibration to reach the 16008B when performing an OPEN i correction The upper electrode of the 16008B is not fixed when setup for an OPEN correction and vibration will cause the upper electrode to move about leading to OPEN correction instability Applying Contact Pressure The 16008B can apply contact pressure on the DUT of up to approximately 10 kg The contact pressure Load Scale shows the approximately applied contact pressure in kilograms To adjust the contact pressure turn the load knob clockwise cw Figure 3 3 shows how to read the load scale ilim w a This indicates 3 kg 103002 Figure 3 3 Load Scale Operation 3 3 Caution Do NOT adjust the contact preasure setting past the 10 kg mark or the 16008B may be machanically damaged Operation Step by step instructions on how to make a measurement with the 16008B are as follows Warning Do NOT touch the electrode and UNKNOWN connector while the High Voltage indicator is lit which shows the 4339B s output is a high voltage of
Download Pdf Manuals
Related Search