Installation, Maintenance and Service Manual FP
Contents
1. ccccccee 15 2 14 Truck ReguremeNS uvsmjananniskme 7 5 2 Torque Specmicatibns un vinruivv 15 2 15 Operators Controls sunajsmsusmmnpun 8 2 16 Industry Standards Lasses 8 2 17 Clamp Open Control cuisses 8 2 of 15 Allied stems 45 036 REV 2 12 ONG REACH Notice When you receive your attachment locate the Long Reach nameplate upper left corner on the body and record the information to the blank nameplate tag with the date received in the space provided on the bottom of this page If the name plate is missing look for the serial number stamped directly into the metal at the original location and consult factory Date received SECTION 1 NAMEPLATE LOCATION O www alliedsystems com m 7 NN e one Readh his oi 2 SSS Allied Systems Company b MODEL NO SERIAL NO MAXIMUM HYD PRESS PSI WEIGHT LBS CAPACITY LBS inch LC SEE TRUCK NAMEPLATE FOR COMBINED TRUCK amp ATTACHMENT NET CAPACITY LOST oo inches a inches LOAL inches CG AND AET SPECIFICATIONS ARE APPROXIMATE AET A Manufactured By Allied Systems Company 211 Oregon Street Sherwood OR 97140 USA 2500005 R O 45 036 REV 2 12 Allied COMPANY 3 of 15 SECTION 2 SAFETY SUMMARY 2 1 Safety Information Safety is Everyone s Responsibility2. 4 of 15 Allied COMPANY Indicates a hazardous situation which if not avoided could result in minor or moderate injury or equipment damage or void the machine warranty Carefully read the message that follows to prevent minor or moderate injury Notice Describes information that is useful but not safety related All possible safety hazards cannot be foreseen so as to be included in this manual Therefore the operator must always be alert to possible hazards that could endanger personnel or damage to the equipment Obey the following warnings before using your machine to avoid equipment damage personal injury or death 2 4 Operation Warnings e You must be trained to operate this equipment prior to operation Be extremely careful if you do not nor mally operate this machine Reorient yourself to the machine before starting then proceed slowly e Always operate an attachment from the driver s seat e Always lower the attachment if you need to leave the lift truck A lift truck supporting a load requires your full attention 2 5 Hydraulic Hazards Danger Small hydraulic hose leaks are extremely dangerous and can inject hydraulic oil under the skin even through gloves Infection and gangrene are possible when hydraulic oil penetrates the skin See a doctor immediately to prevent loss of limb or death 45 036 REV 2 12 ONG REACH e Wear personal protective equipment such as gloves and safety glas
3. The model description found on your shipped invoice will state the following truck requirements flow gpm psi and min truck carriage width The truck carriage must conform to the American National Standard ANSI dimensions shown in ANSI ITSDF B56 11 4 2005 reaffirmed 2000 Make sure the truck carriage is clean conforms to ANSI recommendations and the notches are not damaged 3 2 Hydraulics iL The truck hydraulic system must supply to the at tachment hydraulic oil that meets the specifications required to operate the attachment properly When the truck hydraulic system pressures exceed this maximum a relief valve is recommended in the attachment auxiliary system of the truck or on the attachment Consult the truck factory and or Long Reach for guidance 3 3 Attachment Installation 1 10 of 15 Prior to connecting the truck hydraulic system to the attachment the system must be purged through the filtration system This will eliminate any contamination that might exist in the auxiliary hydraulic system of the truck Allied COMPANY The capacity of the truck and attachment combination may be less than the capacity shown on the attachment alone consult truck nameplate Purging can be accomplished by installing a jumper line and operating each hydraulic function clamp rotate and side shift if equipped in each direction for a minimum of 30 seconds Figure 3 1 To truck y attachment Fi
4. s position should serve the same function as moving a control lever to the rear 2 17 Clamp Open Control Effective October 7 2010 a new safety standard ANSI ITSDF B56 1 Section 7 25 7 for all lift trucks with a load bearing clamp paper roll clamp carton clamp etc requires the driver to make two distinct motions before opening or releasing the clamp For example you must press a switch and then move a lever to unclamp the load This requirement applies to new and used attachments being mounted on new trucks shipping from the factory after October 7 2010 and is a recommended feature to be installed on dealer orders and existing applications 45 036 REV 2 12 ONG REACH Direction of motion Function Load Operator s hand on control handle facing the load Up Rearward or up Hoist Down Forward or down Retract Rearward or up Reach Extend Forward or down Rearward Rearward or up i Forward Forward or down i i Right Rearward or up Sideshift Left Forward or down Rearward Rearward or up Push pull Forward Forward or down Clockwise Rearward or up Rotate lateral Counterclockwise Forward or down f Rearward Rearward or up Rotate longitude Forward Forward or down Ri Down Rearward or up Load stabilizer Up Forward or down Right Rearward or up Swing Left Forward or down Clockwise Rearward or up Slope Counterclockwise Forward or down a Together Rearward or up Fork
5. Whether you are new on the job or a seasoned veteran these safety tips may prevent injury to you to others or to the materials you are handling Always be alert watch out for others and follow these suggestions Attachments handle material not people Safety starts with common sense good judgement properly maintained equipment careful operation and properly trained operators The safety instructions and warnings as documented in this manual and shipped with the machine provide the most reliable procedures for the safe operation and maintenance of your Long Reach attachment It s your responsibility to see that they are carried out 2 2 Safety Regulations Know your company s safety rules Some companies have site specific directions and procedures The meth ods outlined in your operator s manual provide a basis for safe operation of the machine Because of special condi tions your company s material handling procedures may be somewhat different from those shown in this manual 2 3 Safety Symbols The following terms define the various precautions and notices I Danger Indicates a hazardous situation which if not avoided will result in death or serious injury Carefully read the message that follows to prevent serious injury or death Indicates a hazardous situation which if not avoided could result in death or serious injury Carefully read the message that follows to prevent serious injury or death
6. or lubrication procedures while the ma chine is moving or the engine is running Always perform all maintenance and lubrication pro cedures with the machine on level ground parked away from traffic lanes Notice Local laws and regulations may require that additional safety measures be taken Never rely on the hydraulic system to support any part of the machine during maintenance or lubrication Never stand under a component that is supported only by the hydraulics Make sure it is resting on its mechanical stops or appropriate safety stands Use caution when working around hot fluids Always allow lubricating and hydraulic oils to cool before draining Burns can be severe Use extreme caution when using compressed air to blow parts dry The pressure should not exceed 30 psi 208 kPa at the nozzle Never use compressed air on yourself Air pressure penetrating your skin can be fatal Engine exhaust fumes can cause death If it is neces sary to run the engine in an enclosed space remove the exhaust fumes from the area with an exhaust pipe extension Use ventilation fans and open shop doors to provide adequate ventilation Before disconnecting hydraulic lines be sure to lower all loads and relieve all hydraulic pressure The load could fall on you or escaping hydraulic oil could cause severe personal injury Prevent personal injury or equipment damage by us ing a lifting device with a lifting capacity greater than t
7. position Apart Forward or down a Engage Rearward or up ri Release Forward or down Gii Engage Rearward or up ri k Release Forward or down o Raise Rearward or up Truck stabilizer Lower Forward or down Clamp Rearward or up Clamp Release Forward or down For high lift order picker trucks and center control pallet trucks predominant motion of the operator s hand when actuating the control handle while facing away from the load The sense of rotation of the control handle is intended to be in the same direction as the desired motion of the mast or load Figure 2 6 ANSI ITSDF Sequence of location and direction of motion for lever or hand type controls 45 036 REV 2 12 Allied 90f15 COMPANY SECTION 3 INSTALLATION PROCEDURE 3 1 Truck Requirements Long Reach attachments have been designed to oper ate within specific limits Operating pressures above the stipulated maximum may cause structural damage to the attachment and may result in loss of warranty Hydraulic flow less than the recommended rates or the use of small D hoses may reduce operating speed Higher flow can result in excessive heat buildup erratic operation and damage to the truck attachment hydraulic system Notice The dealer and or the user are responsible for installing any valving required to meet the recommended hydraulic pressures and flow The required valving can be furnished by the dealer the truck factory or Long Reach
8. same procedure as above to remove the seals from the gland cap 4 5 Cylinder Inspection Inspect the cylinder tube bore for 1 Deep scratches or nicks 2 Signs of galling or excessive wear 3 Out of roundness or deformities of the barrel Inspect the piston for 1 Scratches or nicks on seal grooves 2 Wear on O D Inspect the cylinder rod for 1 Scratches or nicks on the rod surface 2 Straightness of the rod 3 Damaged threads Inspect the gland cap for 1 Scratches or nicks in seal grooves 2 Damaged threads or spanner wrench holes 3 Excessive wear in bore Replace any component found to be defective 4 6 Cylinder Assembly 1 Spray the piston gland cap and seals with WD40 or other similar product to ease slipping of the seals in place 13 of 15 Allied COMPANY 2 Note the direction of the seal on the piston Improper installation will result in poor performance The cupped side or O ring side of the seal should be facing the gland cap Figure 4 5 Seal Piston Piston nut O ring Figure 4 5 Piston Seal 3 Install the seals and wipers in the gland cap Note the direction of the seals The cupped side or O ring side of the seal should be facing the piston Figure 4 6 Seal Backup ring Lock ring O ring i Wy Retaining ring 77 2 Gland cap on Wiper ring a Cylinder rod Figure 4 6 Gland Cap Seal Install
9. to an accident or damage to the machine Stop the machine immedi ately if problems arise after starting Check to make sure the attachment on your truck is the same as on the truck capacity plate Check for hydraulic leaks and cracked hoses or fit tings Check the hydraulic oil level in the lift truck hydraulic reservoir All electrical cables and connectors must be in good condition Use caution in wet weather to avoid danger from electrical shock Always check the attachment for proper fit and en gagement of the truck carriage 2 11 Personnel Safety 6 of 15 When removing or installing dismountable at tachments always keep hands and feet free from dangerous positions or pinch points Never leave a dismounted attachment in a dangerous position Allied COMPANY Keep hands feet long hair and clothing away from power driven parts Do not wear loose fitting clothing or jewelry while performing maintenance and lubrica tion in these areas Never jump on or off the machine Never stand on top of material being raised lowered or transported Figure 1 Figure 3 Never use the attachment or its load to support a man carrying device Never allow anyone under a load or under the car riage Figure 2 Never stand in front of or beside an attachment that is being operated Never allow another person to ap proach an attachment that is being operated Figure 3 Never leave an attachment or load in an elevated
10. e away from the operator Figure 5 Fork position Sideshift Push pull Figure 2 5 Operator controls Rotate 8 of 15 Allied COMPANY Lifting speed is controlled by the speed of the engine and the position of the control lever Engine speed has no effect on lowering speed Before going on the job shift the truck control levers one way and then the other to determine which direction the attachment moves when the levers are shifted Make sure the attachment moves smoothly throughout its travel without binding or pinching hoses If the attachment does NOT operate smoothly do not take it on the job Check with your supervisor about needed repairs to avoid injury or equipment damage 2 16 Industry Standards ANSI ITSDF B56 1 2009 is the published sequence and direction standard for lever and hand type controls Notice The chart on the following page shows industry standards Your equipment may be different If you do not routinely operate this equipment refresher training is recommended You must reacquaint yourself with this manual and the equipment before starting and then proceed slowly Special controls such as automatic devices should be identified preferably according to the recommendations in Figure 6 When a function is controlled by a pair of push buttons they should operate in the same sense as the lever con trols For example pushing a button located to the rear relative to the operator
11. es from the truck s hydraulics to the fork positioning valve on the attachment Figure 3 3 a To truck To fork positioning cylinders Figure 3 3 Fork Positioning Connection Allied COMPANY Inspect installation to ensure hoses are not kinked or pinched between the truck carriage and attachment Operate the attachment continuously for several minutes to determine that all hydraulic connections for the sideshift cylinder and fork positioning cylinders are secure with no leaks With the mast in the vertical position extend the sideshift cylinder and for positioning cylinders fully After this procedure check that the truck s hydraulic reservoir oil level is at the recommended level Before placing the attachment in operation check the following a Inspect all hoses and fittings for leaks and rout ing clearance Be sure to include clearance of jumper hoses to the mast b Check the cylinder for leaks c Check hair pins at each end of the cylinder for security After completing the installation operate the attach ment without a load for several cycles to remove any air in the hydraulic system Test the attachment with a load to make sure the attachment operates correctly 11 of 15 SECTION 4 SERVICE PROCEDURE 4 1 Attachment Removal 1 Position the attachment forkss to the width of the unit s body Before disconnecting any hydraulic connections be s
12. fonc REACH Installation Maintenance and Service Manual FP 45 036 REV 2 12 Allied 1 of 15 COMPANY TABLE OF CONTENTS Section 1 Nameplate Location 3 Section 3 Installation Procedure 10 Section 2 Safety Summary rrrrnvvvvvvnnnnnnnnn 4 3 1 Truck Reguremens 2 uauassvadnsn 10 2 1 Safety Informationsu svmsanumannnem e 4 3 2 MydAMES een er ae re 10 2 2 Safety Regulations morrrnrrronrrnrenrenne 4 3 3 Attachment Installation oenreonnnnnn 10 2 3 Safety SYMONS eccsuscasszcascdancnanctainesuesasnase 4 3 4 Sideshift Installation eee 11 2 4 Operation WarningS ccccscceseseeeseees 4 3 5 Hydraulic Connections 11 25 Hydraulic Hazards sasjmmsengeanedm 4 Section 4 Service Procedure 0 12 2 6 Electrical Ma2 rds uansett 5 4 1 Attachment Removal eee 12 2 7 Maintenance Warnings eeernnnnnnnnnnvnnnnn 5 4 2 Cylinder Removal sonnnrnnnronnnrnrrnnnnnrnnr 12 2 8 Tainig sesers are ei 6 4 3 Cylinder Installation 0 0 0 0 12 29 Labeling edit 6 4 4 Cylinder Disassembly rrnnnnnnrrrnnnvvnnr 12 2 10 Pre Start Checks uacssmnsmmsigm 6 4 5 Cylinder Inspection scsesscarieamoseranecsvaivecs 13 2 11 Personnel Safety rrrnrrnnnnnnnnrnnnnnnnrr 6 4 6 Cylinder Assembly rrnnnnnnrnnnrnnrrrnnnrrnnr 13 2 12 Load Handling sncccerseecincadimreetaaoncuaees 7 Section 5 Maintenance ccccccssseeee 15 2 13 Load Positioning sesoses a 7 5 1 Maintenance Schedule
13. gure 3 1 Jumper Line Remove the lower retainer hooks Center the truck behind the attachment and drive toward the attachment with the mast tilted forward approximately 4 degrees Slowly raise the truck carriage completely to engage the top hooks with the truck carriage Tilt carriage back until the unit is against the carriage bottom fork bar 0 degrees Inspect for proper engagement of the top hooks Inspect any wear strips if applicable to insure they are properly aligned in the top hooks Install the lower retainer hooks Inspect clearance to the carriage on lower hooks Apply grease to wear strips through the top hooks fittings and spread on entire slide area Check all fittings connections and bolts for any interference 45 036 REV 2 12 ONG REACH 3 4 Sideshift Installation 1 Attach the side shift cylinder s rod end to the attach ment Install the lines from the truck s hydraulics to the sideshift cylinder Inspect installaion to ensure hoses are not kinked or pinched between the truck carriage and attachment Extend the sideshift cylinder half stroke Keeping the cylinder horizontal locate position of the cylinder truck mount Figure 3 2 Figure 3 2 Sideshift Installation 6 Tack weld cylinder truck mount in position and inspect cylinder for parallelism with carriage 7 Weld cylinder truck mount securely 3 5 Hydraulic Connections 1 45 036 REV 2 12 Install the lin
14. h stacking Limit sideshift movement to a minimum when high stacking Always be observant when high stacking Look for poorly stacked loads overhead obstacles broken cartons or damaged products in the stack Travel slowly around corners Sound horn on blind corners Be careful of tail swing and overhead clear ances Watch in all directions Avoid sudden stops 2 14 Truck Requirements Prior to connecting the truck hydraulic system to the at tachment the truck hydraulic system must be cleaned through the filtration system This will eliminate any contamination that may exist in the auxiliary hydraulic system of the truck Allied COMPANY 7 of 15 The capacity of the truck and attachment combined may be less than the attachment capacity Consult truck nameplate Notice The dealer and or the user are responsible for installing any valving required to meet the recommended hydraulic pressures and flow The required valving can be furnished by the dealer the truck factory or Long Reach 2 15 Operator s Controls Some lift trucks are equipped with a single lever to control both hoist and tilt functions others have separate levers for each function Refer to your lift truck manual for more information For clarity the direction of arm movement is shown on the control handle To move the arms in the direction shown pull the handle towards the operator To move the arms in the opposite direction the push the handl
15. lamped load Never use chains cables or other devices in conjunc tion with an attachment for load handling Never clamp loads other than what the attachment was designed to handle Always carry cylindrically shaped loads in the vertical position not the horizontal Always clamp loads with the contact pads if appli cable not the arm or arm base Never rotate a load that is off center to the centerline of rotation Severe damage to the rotator could result Always ensure that the load is the same width as the pallet and neatly stacked when using a carton clamp 2 13 Load Positioning Be accurate in load placement It s important to know what the load will do when it s released Always carry loads as close to the floor as possible consistent with the surface being traversed Scraping or bumping the floor surface with the load or the at tachment can severely damage the attachment and cause product damage The mast should be tilted back Always keep the load positioned as close as possible to the horizontal center of the lift truck Always back down ramps or inclines Driving forward down a ramp or incline with a clamped load will lessen the stability of the truck Figure 4 Figure 4 Do not cross dock boards or dock levelers with the attachment or carriage fully lowered Ramming the front or rear of the attachment against a dock board can cause severe damage Limit lift truck movement to a minimum when hig
16. minal Thread Size Series 45 036 REV 2 12 Allied 15 of 15 COMPANY
17. position Never reach through the mast of the truck Keep all parts of the body within the drivers compartment 45 036 REV 2 12 ONG REACH Always operate an attachment from the operator s seat never while standing next to the lift truck Do not allow riders on the truck at any time Always use reverse when carrying a load that impedes full vision Watch for pedestrians when transporting Always use personal protective equipment PPE appropriate to the situation 2 12 Load Handling 45 036 REV 2 12 Treat an unloaded forklift with an attachment as par tially loaded Never overload the attachment Refer to the attach ment nameplate for the rated capacity of the attach ment Refer to the truck nameplate for the maximum net working capacity of the truck attachment combi nation Never use a load to support or move another object Doing so can easily exceed the holding capac ity of the attachment Always check loads to be handled Correct loads that are broken unbalanced loose or too heavy Never lift lower side shift pivot rotate or tilt loads while traveling Repositioning loads while traveling af fects the stability of the truck and may impede vision or clearances Do not use an attachment to open or close boxcar doors Doing so can severely damage the attachment and cause loss of warranty Damage to clamp arms may result in product damage Do not carry loose items or unsupported loads on top of a c
18. s power and activate the positioning cylinders several times to bleed out trapped air When hydraulic service has been performed activate the hydraulic functions several times to bleed out trapped air in the system before returning attachment to service 4 4 Cylinder Disassembly 1 Remove the cylinder from the attachment See re moval instructions 2 Clamp the cylinder lightly at the base end in a soft jawed vise Use a block or other support under the rod end of the cylinder Figure 4 1 Figure 4 1 Cylinder Vise 3 Spread and remove the retaining ring from the gland cap Push gland inward 1 inch and pry out lock ring 5 Remove the rod assembly from the cylinder tube 45 036 REV 2 12 ONG REACH 6 Clamp the rod assembly in a soft jawed vise on the wrench flats not on the rod surface If the rod does not have wrench flats use two pieces of wood on both sides of the rod to prevent scaring Figure 4 2 ye lt a N AN A lt iad lt A PER gt P BF xo wae wee SY SG Figure 4 2 Cylinder Shaft 7 Remove the piston retaining nut and remove the piston Figure 4 3 Retaining ring Lock ring Gland cap Figure 4 3 Rod Assembly 8 Carefully pry up on the piston seals using a blunt tip screw driver being careful not to scratch the seal grooves Cut the seals to remove from the piston Figure 4 4 45 036 REV 2 12 Figure 4 4 Piston Seal 9 Use the
19. ses whenever servicing or checking a hydraulic system e Assume that all hydraulic hoses and components are pressurized Relieve all hydraulic pressure before disconnecting any hydraulic line e Never try to stop or check for a hydraulic leak with any part of your body use a piece of cardboard to check for hydraulic leaks yam 2 6 Electrical Hazards Remain at least 25 feet from high voltage electrical wires Failure to do so may result in injury or death and will damage equipment e All electrical cables and connectors must be in good condition free of corrosion damage etc Use cau tion in wet weather to avoid danger from electrical shock Never attempt electrical testing or repair while standing in water Do not wear electrically conductive jewelry clothing or other items while working on the electrical system 2 7 Maintenance Warnings Maintenance lubrication and repair of this machine can be dangerous unless performed properly You must have the necessary skills and information proper tools and equipment Work in a method that is safe correct and meets your company s requirements e Do not attempt to make adjustments or perform maintenance or service unless you are authorized and qualified to do so 45 036 REV 2 12 Include attachments in a scheduled maintenance and inspection program Tailor inspection steps to the attachment Unless specified in service procedures never attempt maintenance
20. the gland cap on the cylinder rod being ex tremely careful not to cut the rod seal on the threads of the rod or rod shoulder If available use a sleeve to cover the rod threads or plastic electrical tape Install the piston on the rod and tighten the locknut to 90 ft lbs 0 56 UNF 22 ft lbs 0 75 UNF Spray the inside of the cylinder tube with lubricant to ease inserting the rod and piston Insert the rod and piston into the cylinder tube Tap the rod in with a rubber mallet if resistance is encountered Press on the lock ring and spread retaining ring to install onto the gland cap 14 of 15 Allied stems 45 036 REV 2 12 ONG REACH SECTION 5 MAINTENANCE 5 1 Maintenance Schedule 5 2 Torque Specifications Daily 1 Visually inspect all hoses fittings and cylinder for signs of hydraulic leaks Unless otherwise specified SAE Grade 5 Capscrews Torque Ft Lbs 2 Visually inspect for external damage or cracks i ma inches Dy 100 Hour Maintenance K 0 20 K 0 15 1 Complete the above daily checks 2 Check all hoses and fittings for wear or damage Inspect for hydraulic leaks 3 Check for loose or missing bolts 4 On the forks and top hooks check grease fittings to ensure that they are clean and properly working 5 Check wearstrips on the top hooks Wearstrips should be replaced before top hooks contact car riage 200 Hour Maintenance 1 Re torque top hook bolts per chart Notes No
21. ure to turn off the truck s power and activate the truck s hydraulic functions in both directions to bleed off the hydraulic pressure 2 Disconnect the hydraulic connection for the attach ment positioning at the side shift cylinder 3 Slightly raise the truck carriage to allow the removal of the lower retainer hooks 4 Position the attachment on the edge of a pallet Lower the attachment so that the lower carriage bar misses the pallet when lowered Tilt the mast forward to allow the carriage to disengage from the upper mounting hooks and back away If lowering onto a floor blocks of wood can be place under the body of the attach ment to raise the rear 5 To reinstall follow the installation procedure in this manual When hydraulic service has been performed activate the hydraulic functions several times to bleed out trapped air in the system before returning attachment to service 4 2 Cylinder Removal 1 Disconnect the hydraulic connections 2 Remove the cylinder rod end hair pin and clevis pin 3 Remove hair pin and clevis pin at the base end of the cylinder 4 3 Cylinder Installation 1 Install the clevis pin and hair pin into the base end of the cylinder 2 Attach the hydraulic connections to the cylinder Extend the cylinder until the rod end hole lines up with the mounting hole Install the clevis pin and hair pin into the rod end of the cylinder 12 of 15 Allied COMPANY 4 Turn on the truck
22. wice the weight of any equipment to be lifted Allied oe COMPANY 2 8 Training Make sure all operators are trained in the fork and attachment adaptation operation and use limitations Retrain an operator if a new attachment is added to the forklift Consult the operator s manual for instruc tions on how to use the new equipment Know the mechanical limitations of your forklift Modifications or additions that affect capacity or safe operation must have prior written approval from the forklift truck manufacturer Capacity operation and maintenance instruction plates tags or decals shall be changed accordingly Never use free rigging for a below the forks lift It could affect the capacity and safe operation of a lift truck 2 9 Labeling Change capacity operation and maintenance instruc tion plates tags or decals when a forklift truck is equipped with an attachment If the truck is equipped with front end attachments other than factory installed attachments truck must be marked to identify the attachments and show the approximate weight of the truck and attachment combination at maximum elevation with load laterally centered 2 10 Pre start Checks Check your equipment before you operate it If any thing looks wrong unusual or different report it before using the attachment Do not operate this machine if you know of malfunc tions missing parts and or mis adjustments These situations can cause or contribute
Download Pdf Manuals
Related Search