MY-1026 Service Manual
Contents
1. Paper weight 15 Ibs to 21 Ibs Paper capacity One paper tray with capacity for 250 sheets of 21 Ib bond paper Weight Approx 6 6 Ibs 3 kg Dimensions 19 6 W x 15 6 D x 3 5 H 498 mm W x 395 mm D x 88 mm H Power supply Drawn from the copier MY 1026 GENERAL 1 1 2 UNPACKING AND INSTALLATION The unpacking and set up procedure shall be done by a qualified service technician 1 MY 1026 Installation Manual e Parts included Turn the main switch to the OFF position and removethe power plug from the outlet 1 Remove the DV cartridge and the drum cartridge from the copier Open the tray the side door and the front cabinet and then remove the DV cartridge and the drum cartridge Note Be sure to carry out the operation in the order of 1 2 3 and 4 2 Make the copier upright Close the front cover side cover and bypass tray and then make the copier upright in the orientation shown in the illustration 0 3 4 Remove the OP gear cover and rubber feet from the bottom of the copier Remove the screw and remove the OP gear cover Then take off and remove the rubber feet Oa 7 7 e 0 cS an J Ee Rubber foot gear cover Rubber foot LS SC EE lie Install the s2. connection arm on the 2nd connection arm Spring B Be sure to install so that the earth spring C is in contact under the bearing D 1026 3 2 CAUTION FOR BATTERV REPLACEMENT Danish ADVARSEL Lithiumbatteri Eksplosionsfare ved fejlagtig h ndtering Udskiftning ma kun ske med batteri af samme fabrikat og type Lev r det brugte batteri tilbage til leverandoren English Caution Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to manufacturer s instructions Finnish VAROITUS Paristo voi rajahtaa jos se on virheellisesti asennettu Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin Havita kaytetty paristo valmistajan ohjeiden mukaisesti French ATTENTION a danger d explosion s a remplacement incorrect de la batterie Remplacer uniquement avec une batterie du m me type ou d un type quivalent recommand par le constructeur Mettre au rebut les batteries usag es conform ment aux instructions du fabricant Swedish VARNING Explosionsfara vid felaktigt batteribyte Anvand samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren Kassera anv nt batteri enligt fabrikantens instruktion German Achtung Explosionsgefahr bei Verwendung inkorrekter Batterien Als Ersatzbatterien d rfen nur Batterien vom gleichen Typ oder vom Her
3. turning plate in the paper tray by rotating it in the direction of the arrow and store it in the specified position 10 Set the paper tray side guide Squeeze the lever of the paper tray side guide to slide the guide to the position for the paper size to be used 7 Return the copier to the normal orientation When returning the copier to the normal orientation gently return it without giving a shock RA K lt dl d 1026 UNPACKING AND INSTALLATION 2 2 11 Load paper into the paper trav When loading paper do not exceed the maximum height line 12 Insert the power plug into the outlet and turn the main switch to the ON position Then perform the following procedure 13 Perform SIM setting Execute simulation 26 3 and enter 1 14 Check the center displacement Place an original on the document glass and make a copy using the tray in the copier Then make a copy using the tray in the installed optional paper feed unit If the center of the copy from the optional paper feed unit is dis placed from the copy from the tray in the copier adjust the center referring to the service manual MY 1026 UNPACKING AND INSTALLATION 2 3 3 1026 1 Disassembly and assembly No Part name Ref Paper sensor Cassette detection SW Paper feed solenoid Tran
4. TOSHIBA SERVICE MANUAL PAPER FEED UNIT File No SME04003800 RO4122173900 TTEC 00 2005 02 2005 TOSHIBA CORPORATION rights reserved Parts marked with A are important for maintaining the safely of the machine Be sure to replace these parts with the replacement parts specified to maintain the safetv and performance of the machine General Precautions for Installation Servicing Maintenance for the 1026 The installation and service should be done a qualified service technician 1 When installing the MY 1026 to the Equipment be sure to follow the instructions described in the Unpacking Set Up Procedure for the MY 1026 booklet which comes with each unit of the MY 1026 The MY 1026 should be installed by an authorized qualified person Before starting installation servicing or maintenance work be sure to turn OFF and unplug the equipment first When servicing or maintaining the MY 1026 be careful about the rotating or operation sections such as gears pulleys sprockets cams belts etc When parts are disassembled reassembly is basically the reverse of disassembly unless otherwise noted in this manual or other related materials Be careful not to reassemble small parts such as screws washers pins E rings toothed washers to the wrong places Basically the machine should not be operated with any parts removed or disassembled Delicate parts for preventing safety h
5. azard problems such as switches sensors etc if any should be handled installed adjusted correctly Use suitable measuring instruments and tools During servicing or maintenance work be sure to check the serial No plate and other cautionary labels if any to see if they are clean and firmly fixed If not take appropriate actions 10 The PC board must be stored in an anti electrostatic bag and handled carefully using a 11 wristband because the ICs on it may be damaged due to static electricity Before using the wrist band pull out the power cord plug of the equipment and make sure that there is no uninsulated charged objects in the vicinity For the recovery and disposal of used MY 1026 consumable parts and packing materials it is recommended that the relevant local regulations rules should be followed 12 After completing installation servicing and maintenance of the MY 1026 return the MY 1026 to its original state and check operation CONTENTS i ti a aa ta 2 UNPACKING AND INSTIALLATION 3 MY 1026 1 GENERAL 1 Outline and specifications of each option A MY 1026 250 Sheet Paper Feed Unit The paper feed unit provides the convenience of increased paper capacitv for the copier and a greater choice of paper sizes readilv available for copving Part names Side cover Trav Specifications Copv paper size 5 1 2 x 8 1 2 to 8 1 2 x 14
6. econd cassette unit to the copier If the second cassette unit is aligned to the copier it can be posi tioned automaticallv Hold the copier lightly to prevent it from toppling down and secure the second cassette unit with four screws M4 x 16 MY 1026 UNPACKING AND INSTALLATION 2 1 5 Remove the rear cover and connect the connector 8 Insert the drum cartridge and the DV cartridge into the copier Remove the screw and remove the rear cover Open the trav the side door and the front cabinet insert the drum Then connect the connector of the second cassette unit to that of cartridge and the DV cartridge and then close the front cabinet the copier the side door and the trav Note Be sure to carrv out the operation in the order of 1 2 3 and 4 6 Attach the rear cover Attach the rear cover to its original position and secure it with the 9 Remove the paper tray lock for packing screw M4 x 12 Remove the paper tray lock for packing that secures the
7. sport roller Paper feed clutch nm O oO 2nd paper feed roller Paper feed unit removal 1 Remove the screw 2 Remove the rear cover When installing engage the pawl and install the unit 1 Open the right cabinet 2 Remove three screws 3 Remove one connector from MCU 4 While tilting down the 2nd connection arm A pull and remove the paper feed unit toward you When installing securely insert two bosses C on the machine side and two bosses D on the paper feed unit side Be sure to secure the ground wire B Insert the 2nd page feed A Paper sensor 1 Remove the pawl 2 Remove the paper sensor 3 Remove the harness MY 1026 3 1 1 2 3 1 2 3 D 1 2 Cassette detection switch Remove the pawl Remove the cassette detection switch Remove the harness Paper feed solenoid Remove the screw Remove the connector Remove the paper feed solenoid Transport roller Remove two E rings Remove the transport roller Install so that the earth spring A is brought into contact over bearing B 1 2 3 1 2 Paper feed clutch Remove the E ring Remove the paper feed clutch Remove the parts When installing fit the cut surface A 2nd paper feed roller Remove the E ring and the parts Remove the 2nd paper feed roller When installing hang the 2nd
8. steller empfohlene Batterien verwendet werden Entsorgung der gebrauchten Batterien nur nach den vom Hersteller angegebenen Anweisungen CAUTION FOR BATTERY DISPOSAL For USA CANADA Contains lithium ion battery Must be disposed of properly Remove the battery from the product and contact federal or state environmental agencies for information on recycling and disposal options Trademark acknowledgments Windows and Windows NT are trademarks of Microsoft Corporation in the U S A and other countries IBM and PC AT are trademarks of International Business Machines Corporation PCL is a trademark of Hewlett Packard Companv Pentium is a registered trademark of Intel Corporation All other trademarks and copyrights are the property of their respective owners TOSHIBA TOSHIBA TEC CORPORATION 2 17 2 HIGASHIGOTANDA SHINAGAWA KU TOKYO 141 8664 JAPAN
Download Pdf Manuals
Related Search