Service Manual
Contents
1. and 6 Service of the service slot on the Text Unit SERVICE SOFTWARE will appear on the screen Remove the jumper wire See i Pin 6 Pa Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode CA1 Chassis 37DM23H 37DT25H 37ET35H 37EM33H and 51DT25H Connect a test pattern to the antenna terminal Tune to this signal Turn the receiver off using the mains button Press the volume down and channel up buttons on the front of the receiver at the same time Keeping these buttons pressed turn the mains on When the set starts up it will be in service mode Release the two buttons NOORWN Use the channel up and down buttons to move between the options Use the volume control buttons to change the data The data is stored automatically at switch off To exit the service mode press the standby button on the remote control Sharp Electronics UK Limited Wz Reference AVW060599 1 eS f Revision 1 White Carry out as required Yellow Carry out as required and whenever the unit comes in for service Red Carry out on all units SHARP ea Month of Issue May 1999 Classification White TELEVISION TECHNICAL BULLETIN Page 3 of 7 CA10 Chassis 51DS02H 51DS03H 51DS05H 59DS03H 59DS05H 59ES03H 59ESO5H 59ESD7H 66DS03H 66DS05H 66ES052. switch off Sharp Electronics UK Limited Wz Reference AVW060599 1 QD S i FS 11273 Revision 1 White Carry out as required Yellow Carry out as required and whenever the unit comes in for service Red Carry out on all units SHARP ea Month of Issue May 1999 Classification White TELEVISION TECHNICAL BULLETIN Page 7 of 7 S3B Chassis DV3750H DV3751H DV5131H and DV5150H 1 Connect a test pattern to the antenna terminal 2 Tune to this signal 3 Connect a jumper wire between terminals 2 and 6 of the service slot on the video PWB 4 Press the MODE button on the remote control 5 SERV will appear on the screen 6 Remove the jumper wire RCE pn ra a E he E i a a BR re E imas PI A om A NA J ij a po E E i i E Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode Sharp Electronics UK Limited O Reference AVW060599 1 eS f Revision 1 White Carry out as required Yellow Carry out as required and whenever the unit comes in for service Red Carry out on all units
3. up buttons on the front of the receiver at the same time Keeping these buttons pressed turn the mains on When the set starts up it will be in service mode and SERVICE SOFTWARE will appear on the screen Release the two buttons Tore ey Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode Sharp Electronics UK Limited Wz Reference AVW060599 1 eS f Revision 1 White Carry out as required Yellow Carry out as required and whenever the unit comes in for service Red Carry out on all units HARP ae Month of Issue May 1999 Classification White TELEVISION TECHNICAL BULLETIN Page 5 of 7 DECO 4 and Deco 5 Chassis s DV5105H DECO 4 DV5107H DV5132H and DV5135H DECO 5 Connect a test pattern to the antenna terminal Tune to this signal Turn the receiver on Connect a jumper wire momentarily between terminals 2 GND and 6 Service of connector of CN1 on the Video unit Note that the wire is used just like a passing contact switch SHARP Software Service Ver will appear on the screen naa sae a a Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the
4. H and 66ESD7H Connect a test pattern to the antenna terminal Tune to this signal Turn the receiver off using the mains button Press the volume down and channel up buttons on the front of the receiver at the same time Keeping these buttons pressed turn the mains on When the set starts up it will be in service mode Release the two buttons ote SS Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode CS Chassis 51CS03H 51CS05H 59CSO3H 59CSO5H 59CSD8H 66CS03H 66CS05H and 66CSD8H Connect a test pattern to the antenna terminal Tune to this signal Turn the receiver off using the mains button Press the volume down and channel up buttons on the front of the receiver at the same time Keeping these buttons pressed turn the mains on When the set starts up it will be in service mode Release the two buttons Oe Lee ok E Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode CW100 Chassis 66DW18H and 76DW18H 1 Connect a test pattern to the antenna terminal 2 Tune to this signal 3 Turn the receiver off using the mains button 4 Press the volume down and channel up bu
5. SHARP men Month of Issue May 1999 Classification White TELEVISION TECHNICAL BULLETIN Page 1 of 7 MODELS BCTVA Chassis 4BS C Chassis CA1 Chassis CA10 Chassis CW100 Chassis CS Chassis D3000 Chassis DECO 4 Chassis DECO 5 Chassis 4BS B Chassis 4BS A Chassis 5BS A Chassis S3B Chassis To assist with the adjustments of the above chassis the list below details how to enter the various service modes BCTVA Chassis 66AS06H DV5932H DV5935H DV5937H and DV6635H Connect a test pattern to the antenna terminal Tune to this signal Connect a jumper wire between terminals 2 GND and 6 Service of the service slot on the Video Unit SERVICE SOFTWARE will appear on the screen Remove the jumper wire a aS Da Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the receiver off at the mains to exit the service mode Sharp Electronics UK Limited Wz Reference AVW060599 1 eS f Revision 1 White Carry out as required Yellow Carry out as required and whenever the unit comes in for service Red Carry out on all units HARP oe Month of Issue May 1999 Classification White TELEVISION TECHNICAL BULLETIN Page 2 of 7 4BS C Chassis DV5940H DV6640H and 66AS05H Connect a test pattern to the antenna terminal Tune to this signal Connect a jumper wire between terminals 2 GND
6. service mode Sharp Electronics UK Limited O Reference AVW060599 1 eS f Revision 1 White Carry out as required Yellow Carry out as required and whenever the unit comes in for service Red Carry out on all units SHARP he Month of Issue May 1999 Classification White TELEVISION TECHNICAL BULLETIN Page 6 of 7 4BSA Chassis DV3760H DV3770H and DV5161H 1 Connect a test pattern to the antenna terminal 2 Tune to this signal 3 Connect a jumper wire between terminals 3 GND and 6 service of connector TB on the Main PWB 4 Press the MODE button on the remote control 5 SERV will appear on the screen 6 Remove the jumper wire Pin 6 Pin 3 To select an adjustment use the channel up and down buttons To change the data press the data buttons The changes are stored automatically Turn the set off at the mains to exit the service mode 5BSA Chassis 37AM12H 37AM23H 37AT25H and 51AT15H Connect a test pattern to the antenna terminal Tune to this signal Turn the receiver off using the mains button Press the volume down and channel up buttons on the front of the receiver at the same time Keeping these buttons pressed turn the mains on When the set starts up it will be in service mode SERV appears on the screen Release the two buttons oS Use the channel up and down buttons to move between the options Use the volume control buttons to change the data The data is stored automatically at
7. ttons on the front of the receiver at the same time 5 Keeping these buttons pressed turn the mains on 6 When the set starts up it will be in service mode 7 Release the two buttons Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Turn the set off at the mains to exit the service mode BSI Sharp Electronics UK Limited Wz Reference AVW060599 1 eS f Revision 1 White Carry out as required Yellow Carry out as required and whenever the unit comes in for service Red Carry out on all units S HARP CTV990504 Month of Issue May 1999 Classification White TELEVISION TECHNICAL BULLETIN Page 4 of 7 D3000 Chassis DV51083H DV5903H DV59083H DV6603H and DV66083H Connect a test pattern to the antenna terminal Tune to this signal Turn the receiver on Press the service switch S1401 located on the Video PWB nat ae ea Service switch is located here SS eee Use the channel up and down buttons to move between the options Use the volume control buttons to change the data Use the standby button on the remote control to store the data Press the service switch again to exit the service mode 4BS B Chassis DV5165H and DV5180H Connect a test pattern to the antenna terminal Tune to this signal Turn the receiver off using the mains button Press the volume down and channel
Download Pdf Manuals
Related Search