Alligator GKC1000 UK.book
Contents
1. Never let any liquid get inside the tool and never immerse any part of the tool into liquid Oiling Regularly oil the oiling points 15 as indicated in figure D Transport Always transport the tool with the jaws closed and the latch 5 in the locked position Saw Chain sharpening If you are to get the best possible performance from the tool it is important to keep the teeth of the saw chain sharp Guidance for this procedure is found on the sharpener package For this purpose we recommend the purchase of Black amp Decker saw chain sharpening kit A6039 available from Black amp Decker service agents and selected dealers Replacing worn out saw chains Replacement saw chains are available through retailers or Black amp Decker service agents Always use genuine spare parts Saw chain sharpness The saw chain cutters will blunt immediately if they touch the ground or a nail whilst cutting Saw chain tension Regularly check the saw chain tension What to do if your chainsaw needs repair Your tool is in accordance with the relevant safety requirements Repairs should only be carried out by a qualified person using original spare parts otherwise this may result in considerable danger to the user We recommend you keep this user manual in a safe place Storage When the tool will not be used for several months wipe any metal components with oil Ideally leave the battery 6 connected to the charger Proceed as follo2. If the saw chain 14 or guide bar 3 becomes jammed Switch the tool off e Disconnect the battery from the tool Open the cut with wedges to relieve the strain on the guide bar Do not try to wrench the saw free Start a fresh cut Trimming branches fig K Ensure that there are no local by laws or regulations that would prohibit or control the trimming of the tree limbs Make sure the tool is running at full speed before making a cut e Hold the tool firmly in place to avoid possible bouncing or Sideways movement of the tool Guide the tool using light pressure e Always cut down from the top This way you will avoid pinching the saw chain 14 e Remove branches as shown in figure K Starting from the branch tip reduce the branch in logical steps cutting off small sections e Remove the tool from the cut while it is running at full speed Maintenance Your Black amp Decker tool has been designed to operate over a long period of time with a minimum of maintenance Continuous satisfactory operation depends upon proper tool care and regular cleaning Warning Before performing any maintenance on the tool remove the battery from the tool Unplug the charger 9 before cleaning it Cleaning e Regularly remove the chain access cover 11 and remove any debris that has become trapped e Regularly clean the ventilation slots with a clean dry paint brush e To clean the tool use only mild soap and a damp cloth
3. are inherent to the use of wood cutting saws and cannot be avoided These are Risk of injury arising from contact with moving parts sharp paris hot parts branches or debris falling on the operator bystanders or property debris ejected by the tool Risk of injury arising from un intended use falling from a ladder or working position in a tree damage to the supply cable use of the tool in wet or hazardous locations use of the product by young children or infirm persons failure to wear suitable personal protection or suitable clothing breathing dust generated from cutting wood The above risks have been addressed by including warnings in the safety instructions and or markings applied to the tool Noise and vibration Information Noise Typical Noise Emissions according to EN60745 LpA Sound pressure 81 dB A LwA Sound Power 95 dB A KpA sound pressure uncertainty 3 dB A KWA acoustic power uncertainty 3 dB A Vibration Vibration total values triax vector sum determined according to EN 60745 Vibration emission Work mode description Cutting value ah 2 04 m s freshly felled softwood Uncertainty K 1 5 m s The declared vibration emission value has been measured in accordance with a standard test method provided by EN60745 and may be used for comparing one tool with another The declared vibration emission value may also be used in a preliminary assessment of exposure Warn
4. by contacting your local Black amp Decker office at the address indicated in this manual Alternatively a list of authorised Black amp Decker repair agents and full details of our after sales service and contacts are available on the Internet at www 2helpU com Please visit our website www blackanddecker co uk to register your new Black amp Decker product and to be kept up to date on new products and special offers Further information on the Black amp Decker brand and our range of products is available at www blackanddecker co uk Australia Black 8 Decker Australia Pty Ltd Tel 03 8720 5100 20 Fletcher Road Mooroolbark Fax 03 9727 5940 Victoria 3138 New Zealand Black amp Decker Tel 64 9 259 1133 5 Te Apunga Place Fax 64 9 259 1122 Mt Wellington Auckland 1060 United Kingdom Black amp Decker Tel 01753 511234 210 Bath Road Fax 01753 551155 Slough Berkshire SL1 3YD Helpline 01753 574277 90520325 06 07
5. use keep it away from other metal objects like paper clips coins keys nails screws or other small metal objects that can make a connection from one terminal to another Shorting the battery terminals together may cause burns or a fire Under abusive conditions liquid may be ejected from the battery avoid contact If contact accidentally occurs flush with water If liquid contacts eyes additionally seek medical help Liquid ejected from the battery may cause irritation or bums Service Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained Additional safety instructions for the Alligator Lopper Warning Never use the tool above shoulder height Always position yourself out of the path of falling branches and debris Warning Do not use this tool to fell trees Keep all parts of your body and clothing away from the saw chain at all times Hold the tool in front of you and be aware ofthe saw chain position especially when cutting branches near the ground Before you switch on make sure the saw chain is not contacting anything Pre plan a safe exit from falling branches and debris Ensure the exit route is clear of obstacles that would prevent or hinder movement Remember wet grass and freshly cut bark is slippery Be aware of the direction that a branch may fall Consider all conditions that may affect the
6. 4 The tension is correct when the saw chain snaps back after being pulled 3 mm away from the guide bar There should be no sag between the chain guide bar 3 and the saw chain 14 on the underside Note Do not over tension the saw chain as this will lead to excessive wear and reduce the life of the bar and saw chain It will also lead to reduced product performance Note With first use and when the saw chain is new check tension frequently as a new saw chain stretches slightly Replacing the saw chain and chain guide bar After prolonged use the saw chain 14 and or chain guide bar 3 may need replacing Ensure only Black amp Decker recommended replacements are used Removing the saw chain and chain guide bar fig C amp D Always wear protective gloves when installing or removing the saw chain 14 The saw chain is sharp and can cut you when it is not running Warning The chain guide bar and the saw chain may be hot after use Allow to cool before replacing e Place the tool on a firm surface ooo M e Rotate the two retention bolts 12 counter clockwise with the spanner 13 provided and remove completely e Remove the chain access cover 11 e Slide the latch 5 to the unlock position open the handles and pull back the top jaw 1 e Pull back chain guide bar 3 and then lift the saw chain 14 out of the groove in the guide bar The saw chain can then be removed from the unit e Thechain guide bar 3 ca
7. 44 BLACK DEGKER A9IPPUEADE MMM UK Ireland Australia New Zealand DAN i d Nr e ce mv LIN HA I OD e Intended use Your Black amp Decker Alligator Lopper has been designed for trimming the branches of trees cutting fallen branches and cutting small logs 25 mm to 100 mm in diameter while the operator is standing on the ground This tool is intended for consumer use only General safety rules Warning Read all safety warnings and all VN instructions Failure to follow all instructions may result in electric shock fire and or serious injury SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE The term power tool in all of the warnings listed below refers to your mains operated corded power tool or battery operated cordless power tool 1 Work area safety a Keep work area clean and well lit Cluttered and dark areas invite accidents b Donotoperate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes c Keep children and bystanders away while operating a power tool Distractions can cause you to lose control 2 Electrical safety Power tool plugs must match the outlet Never modify the plug in any w
8. ain on to the chain guide bar 3 and an excessive amount of oil applied to the unit could mean the oil drips from the unit around the jaw area This is normal and is nothing to be concerned about Use Charging the battery fig H amp I The battery 6 needs to be charged before first use and whenever it fails to produce sufficient power on jobs that were easily done before When charging the battery 6 for the first time or after prolonged storage it will only accept an 80 charge After several charge and discharge cycles the battery 6 will attain full capacity The battery 6 may become warm while charging this is normal and does not indicate a problem Warning Do not charge the battery at ambient temperatures below 4 C or above 40 C Recommended charging temperature approx 24 C 8 hour charger fig H To charge the battery 6 remove it from the tool and slide the charger receptacle 10 onto the battery 6 e Plug in the charger 9 The battery 6 will be fully charged in approximately 8 hours It can be removed at any time or left in the connected charger indefinitely 1 hour charger fig I To charge the battery 6 remove it from the tool and insert it into the charger 17 The battery 6 will only fit into the charger 17 in one way Do not force Be sure that the battery 6 is fully seated in the charger 17 e Plugin the charger 17 The charge time will depend upon the co
9. ay Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock b Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded c Donotexpose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock d Donotabuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock e When operating a power tool outdoors use an extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock f If operating a power tool in a damp location is unavoidable use a residual current device RCD protected supply Use of an RCD reduces the risk of electric shock Personal safety Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury Use personal protective equipment Always wear eye protection Protective equipment such as dust mask non Skid safety shoes hard hat or hearing protection u
10. cutting only with the chain moving at full speed Watch for shifting branches or other forces that could close a cut and pinch or fall into the chain Use extreme caution when re entering a previous cut Engage spikes on lower jaw into wood and allow the chain to reach full speed before proceeding with cut Use of this tool for operation different to those intended could result in hazardous situations Cut wood only Don t use this tool for purposes not intended for example Don t use tool for cutting plastic masonry or non wood building materials If any debris gets caught with the guard or tool discontinue use remove the battery and clear debris Worn chains and chain guide bars should be replaced Only use replacement bars and chains specified by the manufacturer a Warning symbols The following warning symbols are found on your tool Read the user manual Do not use your saw in wet conditions or expose it to rain Always wear head hearing and eye protection Beware of falling objects Keep bystanders away Do not use on ladders Check the chain tension after every 10 Bw minutes of use Adjust back to a clearance of 3 mm Oil the chain after every 10 minutes of use Warning do not touch chain at the chip ejection point gt Direction of travel of the chain S U eaten Despite the application of the relevant safety regulations and the implementation of safety measures certain residual risks
11. direction of fall including The intended direction of fall The natural lean of the branch Any unusual heavy limb structure or decay Surrounding trees and obstacles including overhead lines The wind speed and direction The safe distance between a branch and debris to be felled and bystanders buildings and other objects is at least 2 1 2 times the length of the branch Any bystander building or object within this distance is at risk from being Struck by the falling branch When cutting a limb that is under tension be aware of spring back When the tension in the wood fibres are released the spring loaded limb may strike the operator and or throw the tool out of control Always wear suitable safety equipment such as non skid safety shoes hard hat goggles ear protection and gloves when operating the tool Ensure someone is nearby at a safe distance in case of an accident Do not attempt to operate the tool when in a tree on a ladder or standing on any other unstable support Keep proper footing and balance at all times Hold the tool firmly with both hands when the motor is running Keep handles dry clean and free from oil and grease Greasy oily handles are slippery causing loss of control Do not let the moving chain contact any object at the tip of the guide bar Keep your saw chain properly tensioned Check tension at regular intervals with the motor stopped and cord disconnected Begin and continue
12. ing The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used The vibration level may increase above the level stated When assessing vibration exposure to determine safety measures required by 2002 44 EC to protect persons regularly using power tools in employment an estimation of vibration exposure should consider the actual conditions of use and the way the tool is used including taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time Additional safety instructions for batteries and chargers Batteries Never attempt to open for any reason Do not expose the battery to water Do not store in locations where the temperature may exceed 40 C Charge only at ambient temperatures between 4 C and 40 C Charge only using the charger provided with the tool When disposing of batteries follow the instructions given in the section Protecting the environment Under extreme conditions battery leakage may occur When you notice liquid on the battery proceed as follows Carefully wipe the liquid off using a cloth Avoid skin contact In case of skin or eye contact follow the instructions below Warning The battery fluid a 25 30 solution of potassium hydroxide can be harmful In case of skin contact immediately ri
13. ligator Lopper is the subject of patent and design applications in Europe the United States and other countries around the world ALLIGATOR is a trade mark of the Black amp Decker Corporation Kevin Hewitt Director of Consumer Engineering Spennymoor County Durham DL16 6JG Guarantee Black amp Decker is confident of the quality of its products and offers an outstanding guarantee This guarantee statement is in addition to and in no way prejudices your statutory rights The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area If a Black amp Decker product becomes defective due to faulty materials workmanship or lack of conformity within 24 months from the date of purchase Black amp Decker guarantees to replace defective parts repair products subjected to fair wear and tear or replace such products to ensure minimum inconvenience to the customer unless The product has been used for trade professional or hire purposes The product has been subjected to misuse or neglect e The product has sustained damage through foreign objects substances or accidents e Repairs have been attempted by persons other than authorised repair agents or Black amp Decker service staff To claim on the guarantee you will need to submit proof of purchase to the seller or an authorised repair agent You can check the location of your nearest authorised repair agent
14. n then be angled up and removed Assembling the chain guide bar and saw chain fig E amp F Warning Always wear protective gloves when installing or removing the saw chain The saw chain is sharp and can cut you when it is not running e Ensure the operation is carried out on a firm surface e Slide the latch 5 to the unlock position open the handles and pull back the top jaw 1 e Insert the chain guide bar 3 into the space between the chain tensioner and align with the chain guide bar locator angle the chain guide bar 3 down ensuring it is correctly located e Place the saw chain 14 around the front of the chain guide bar 3 e Pull the chain guide bar 3 and the saw chain 14 back engaging itin the groove in the chain guide bar 3 and then over the sprocket 16 positioning teeth in the correct position on the sprocket e Replace the chain access cover 11 and the two retention bolts 12 tightening securely e Ensure the saw chain 14 is fitted correctly with reference to the markings on the tool Oiling fig G Before first use and every ten minutes of use you must oil the product with the correct chain oil Cat No A6027 Open the oiling cover 4 and insert the bottle into the oil filling hole 15 apply pressure to the bottle once to dispense oil e This should be adequate for about 10 minutes of cutting depending upon cutting speed and type of wood The hole feeds the oil through to the saw ch
15. ndition and type of battery The charge time is stated in the technical specifications The battery can be removed from the charger at any time or left in the charger indefinitely to maintain a full charge Preparation Carry out regular cleaning of the unit as described in the maintenance section and in particular cleaning inside the chain access cover 11 The lower jaw 2 and top jaw 1 are designed to close when one of the handles is released or when the piece of branch being cut has been cut If this does not occur discontinue use of the tool and remove the battery from the tool Check if any debris is blocking movement To help in this process it may be necessary to remove the chain access cover 11 If on assembly the problem is still present retum the unit to an authorised service centre Switching on and off Warning Never attempt to lock or fix a switch actuator in the on position For your safety this tool is equipped with a double switching System This system prevents starting the tool inadvertently Switching on fig J Ensure a firm grip on the handles and then squeeze both switch actuators 5 to switch the unit on Switching off fig J Release either of the switches Note Both switches must be activated for the product to be used Do not force the tool allow it to do the work It will do a better and safer job at the speed for which it is designed Excessive force will stretch the saw chain
16. nse with water Neutralise with a mild acid such as lemon juice or vinegar In case of eye contact rinse abundantly with clean water for at least 10 minutes Consult a physician e Do not incinerate the battery e Do not attempt to charge damaged batteries Chargers Use your Black amp Decker charger only to charge the battery in the tool with which it was supplied Other batteries could burst causing personal injury and damage Never attempt to charge non rechargeable batteries Have defective cords replaced immediately Do not expose the charger to water Do not open the charger Do not probe the charger The charger is intended for indoor use only D gt Electrical safety Your charger is double insulated therefore no a earth wire is required Always check that the power supply corresponds to the voltage on the rating plate Warning Never attempt to replace the charger unit with a regular mains plug e If the supply cord is damaged it must be replaced by the manufacturer or an authorised Black amp Decker Service Centre in order to avoid a hazard Features Top jaw 2 Lower jaw 3 Chain guide bar 4 Oiling cover 5 Latch 6 Battery 7 On off switch actuators 8 Chipping ejection point 9 1 Charger 0 Charger receptacle Assembly Warning Before assembly remove the battery 6 from the tool Fitting and removing the battery fig A Tofitthe battery 6 line it up wi
17. ool before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tools operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools uU A CO OQ Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control Use the power tool accessories and tool bits etc in accordance with these instructions taking into account the working conditions and the work to be performed Use of the power tool for operations different from those intended could result in a hazardous situation Battery tool use and care Recharge only with the charger specified by the manufacturer A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack Use power tools only with specifically designated battery packs Use of any other battery packs may create a risk of injury and fire When battery pack is not in
18. r nearest authorised repair agent by contacting your local Black amp Decker office at the address indicated in this manual Alternatively a list of authorised Black amp Decker repair agents and full details of our after sales service and contacts are available on the Internet at www 2helpU com Batteries Black amp Decker batteries can be recharged many x times At the end of their useful life discard batteries with due care for our environment Run the battery down completely then remove it from the tool e NiCd and NiMH batteries are recyclable Take them to any authorised repair agent or a local recycling station Technical data GKC1000 GKC1000P GKC1000NM Voltage Vdc 18 18 18 Chain speed milini 1 45 1 45 1 45 No load Maximum 100 100 100 diameter of mm cut Weight kg 3 5 3 5 3 5 Battery A18 A1718 A18NH Voltage Vdc 18 18 18 Capacity Ah 1 5 1 7 1 5 Weight kg 0 8 0 8 0 8 Charger 1hr 8hr Voltage Vac 230 230 Approx charging time 1 5 Ah battery hr 1 5 8 1 7 Ah battery hr 2 10 Weight kg 1 2 0 4 EC declaration of conformity GKC1000 GKC1000P GKC1000NM Black 8 Decker declares that these products conform to 98 37 EC 89 336 EEC EN 60745 EN55014 EN 61000 EN60335 2000 14 EC Chainsaw Annex V Guaranteed sound pressure level measured according to 2000 14 EC LpA sound pressure 81 dB A LwA acoustic power 91 dB A LWA guaranteed 95 dB A United Kingdom 21 06 2007 The Al
19. sed for appropriate conditions will reduce personal injuries Prevent unintentional starting Ensure the switch is in the off position before connecting to power source and or battery pack picking up or carrying the tool Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents Remove any adjusting key or wrench before turning the power tool on A wrench or a key left attached to a rotating part of the power tool may result in personal injury Do notoverreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from moving parts Loose clothes jewellery or long hair can be caught in moving parts If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used Use of these devices can reduce dust related hazards Power tool use and care Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which it was designed Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the Switch is dangerous and must be repaired Disconnect the plug from the power source and or the battery pack from the power t
20. th the receptacle on the tool Slide the battery 6 into the receptacle and push until the battery 6 snaps into place e Toremove the battery 6 push the release button 19 while at the same time pulling the battery 6 out of the receptacle Fitting the battery cap fig L Warning Fit the cap 18 to the battery 6 for transportation and storage Opening the handles fig B To open the handles slide the latch 5 backwards and pull the handles apart e After use close the handles and slide the latch 5 forward to the lock position The handles should be locked during transportation and storage Chain tension adjustment fig C Warning Before adjusting the chain tension or any other adjustments make sure that the tool is switched off and the battery removed Warning The chain guide bar and the saw chain may be hot after use Allow to cool before adjustment The product comes ready assembled However we recommend that you check the tension of the saw chain 14 and chain access cover retention bolts before use and adjust if required Checking and adjusting the saw chain tension fig C To tension the saw chain 14 slacken the two chain cover retention bolts 12 with the spanner 13 and the chain tensioning device will push the chain guide bar 3 out setting the correct tension Retighten the two retention bolts 12 securely Check the correct tension has been set by lightly pulling on the saw chain 1
21. ws Fully charge the battery 6 e Remove the battery 6 from the tool e Store the tool and battery 6 in a secure and dry location The storage temperature must always remain in the range of 5 C to 40 C Place the battery 6 on a level surface e Before using the tool after prolonged storage fully charge the battery 6 again o A Protecting the environment Separate collection This product must not be Xx disposed of with normal household waste Should you find one day that your tool needs replacement or if it is of no further use to you think of the protection of the environment Black amp Decker repair agents will accept old Black amp Decker tools and ensure that they are disposed of in an environmentally safe way OX Separate collection of used products and n amp packaging allows materials to be recycled and used again Re use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials Local regulations may provide for separate collection of electrical products from the household at municipal waste sites or by the retailer when you purchase a new product Black amp Decker provides a facility for the collection and recycling of Black amp Decker products once they have reached the end of their working life To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf You can check the location of you
Download Pdf Manuals
Related Search