Installation Instructions
Contents
1. PLEASE MAKE SURE THEY RECEIVE THIS COPY OF THE INSTALLATION INSTRUCTIONS SO THEY ARE AWARE OF THE IMPORTANT INFORMATION CONTAINED IN THEM TOOLS SUGGESTED 1 Phillips Screwdriver Set of Combination Wrenches Wire Cutter Crimper STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS STEP 1 Read and understand all steps in the instructions before starting the installation Park the motorcycle on a hard level surface and turn off the ignition Let cool A WARNING gt WILL BE WORKING AROUND THE ENGINE AND EXHAUST SYSTEM DURING INSTALLATION ENSURE THAT THE ENGINE AND EXHAUST SYSTEM HAVE FULLY COOLED TO PREVENT INJURY A FACTORY SERVICE MANUAL WILL BE HELPFUL IN PERFORMING THIS Kuryakyn A WARNING INSTALLATION DO NOT ATTEMPT TO PERFORM THIS INSTALLATION IF YOU ARE NOT CONFIDENT IN YOUR ABILITY TO COMPLETE ALL OF THE STEPS IN THE PROCEDURE CONSULT A TRAINED TECHNICIAN IMPROPER INSTALLATION COULD RESULT IN SERIOUS INJURY OR DEATH NOTICE The Mirror Stem Lights are intended for use as SUPPLEMENTAL turn Signals and running lights only Any other use may be in violation of Federal State or local regulations STEP 2 Remove the three Phillips head fasteners from each Lighted Mirror Stem Cover Remove the two covers from each Stem Light Remove each Stem Light PIC 1 STEP 3 Determine the left from the right sitting on the bike chrome cover PIC2. 2 NOTICE Avoid damage to the motorcycle Protect painted surfaces with a soft cloth or blanket STEP 4 Remove the mirrors from the motorcycle as outlined in the service manual Place the chrome cover over the mirror stem PIC 3 Place the Stem Light over the other side of the mirror stem PIC 4 Hold the Stem Light tightly into the cover and see if these two pieces seem loose on the mirror stem If the fit is loose or the assembly seems to rattle remove the cover and place a piece of the included foam tape on the mirror stem as shown in PIC 5 STEP 5 With the Chrome cover in place over the mirror stem place the Stem Light onto the cover Place the top cover over the mirror stem making sure the pin on the top cover fits in the hole on the back cover Fasten with one of the fasteners you removed in Step 2 PIC 6 DO NOT over tighten just snug will do Place the bottom cover over the mirror stem Make sure that the wires from the Mirror Stem Light exit through the channel in the cover PIC 7 Fasten with two of the fasteners removed in Step 2 DO NOT over tighten just snug will do STEP 6 Repeat Step 4 and Step 5 for the remaining Mirror Stem Light PLACE LIGHT OVER STEM AND BACK NOTICE K ryakyn recommends the use of dielectric grease on electrical COVER PIC 5 J connections STEP 7 On 96 and later models with 8 Pin main harness Connectors Remove the d y h seat and locate the H D main wiring harness PIC 8 On trike models loca
3. ING HARNESS STEP 10 Turn the key ON and using a test light or the wiring diagram for ME comes uP THROUGH your bike determine the left and right turn signal power running light power and a ground wire Label each of these wires for their function or write the color and function down Turn the key OFF and disconnect the battery 4 CAUTION potential electrical shock Be sure to disconnect the battery before starting this a Er ig Ba d FRAME D A EN r 4 gt procedure K CONNECTOR ON TRIKES HAS RED WITH YELLOW STRIPE WIRE STEP 11 Place one of the included female T Tap connectors on turn signal power wire from the LEFT turn signal located in Step 10 Place one of the included female T Tap connectors on turn signal power wire from the RIGHT turn signal located in Step 10 Place two of the included female T Tap connectors on the RUNNING light power wire located in Step 10 Place two of the included female T Tap connectors on the GROUND wire located in Step 10 NOTE If there is a run turn brake controller installed the female T Taps need to be installed upstream in front of the controller The installation order must be main harness from front of bike with the female T Taps installed CUT THESE 3 PIN then the controller finally the taillight harness HARNESSES OFF 8 PIN ADAPTER STEP 12 Place a small amount of dielectric grease on the female T Tap connectors insert t
4. INSTALLATION LIGHTED MIRROR STEM COVERS 1757 PARTS INCLUDED CUSTOMER SERVICE 1 Right Lighted Mirror Stem Cover Assembly INSTALLATION QUESTIONS 1 Left Lighted Mirror Stem Cover Assembly ne eel 946 DAF DE 1 Hardware Kit Containing 3 4 X 1 2 Phillips Head Screws Replacement Screws if Needed PE LIMITED WARRANTY 2 Pieces of Single Sided Foam Tape ae a r a 1 Dielectric Grease Pack 8 4 Cable Ties 4 Cord Keepers 1 8 Pin Run Turn Wiring Adapter eK 1 Hardwiring Hardware Kit Containing ae ace 8 Female T Tap Connectors T ONLY 6 OF EACH 8 Insulated Male Spades WILE BE USED 1 Dielectric Grease Pack 1 Installation Instructions Please read and understand entire instructions before starting installation THANK YOU FOR CHOOSING KURYAKYN IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND OR PROPERTY DAMAGE OR LOSS PLEASE PAY CLOSE ATTENTION TO ALL INSTRUCTIONS WARNINGS CAUTIONS AND NOTICES REGARDING THE USE AND CARE OF THIS PRODUCT THIS INDICATION ALERTS YOU TO THE FACT THAT e IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY This indication alerts you to the fact that ignoring the NOTICE contents described herein may negatively affect product performance and functionality This indication alerts you to the fact that ignoring the contents described herein can result in potential injury ekii IF INSTALLING THIS PRODUCT FOR ANOTHER PARTY NOTICE S G S ODUCT FO O j
5. ded melted or frayed wires STEP 14 Place some of the included dielectric grease on each connector Connect the three pin connector on the wire harness from the LEFT Mirror Stem Light to three pin connector on the 8 Pin Run Turn wiring adapter with the PURPLE BLACK BLUE wires PIC 10 Connect the three pin connector on the wire harness from the RIGHT Mirror Stem Light to three pin connector on the 8 Pin Run Turn wiring adapter with the BROWN BLACK BLUE wires PIC 10 STEP 15 Turn the bike on and test that all lights function correctly A WARNING ENSURE PROPER LIGHT OPERATION BEFORE RIDING THE MOTORCYCLE VISIBILITY IS A MAJOR CONCERN FOR MOTORCYCLISTS A LIGHT MALFUNCTION COULD RESULT IN DEATH OR SERIOUS INJURY STEP 16 Replace the seat A WARNING AFTER INSTALLING THE SEAT PULL UP ON IT TO ENSURE IT IS LOCKED INTO PLACE A LOOSE SEAT CAN SHIFT AND CAUSE LOSS OF CONTROL RESULTING IN SERIOUS INJURY OR DEATH PAGE 4 LIGHTED MIRROR STEM COVERS INSTALLATION
6. he insulated male spade connectors from the BLACK wires into the female T Tap connectors that were installed on the GROUND wire insert the insulated male spade PIC 10 connectors from the BLUE wires into the female T Tap connectors that BROWN BLUE were installed on the RUNNING light power wire the insulated male we BLACK WIRES TO spade connector from the BROWN wire to the female T Tap on the a el RIGHT turn power wire and the insulated male spade connector on the i PURPLE wire to the female T Tap on the LEFT turn power wire in the taillight harness A NOTE It may be easier to raise or remove the fuel tank for the next Step Refer to the service manual for your model for PURPLE BLUE detailed instructions on removal of the fuel tank e TO Fae WIRING ADAPTER NOTICE When raising the fuel tank care MUST be taken not to stretch puncture or break CONNECTED TO MAIN the attached fuel line HARNESS PAGE 3 cont LIGHTED MIRROR STEM COVERS INSTALLATION Kuryakyn STEP 13 Route the wire harnesses from each Mirror Stem Light under the fuel tank to the 8 Pin Run Turn wiring adapter or 3 Pin hardwire connectors just installed Secure the harnesses out of harms way using the included cable ties and cord keepers Secure all wiring away from any moving parts pinch points or extreme heat NOTICE Kuryakyn WILL NOT issue a warranty on any electrical component that fails due to pinched crimped broken abra
7. te the ETE 8 pin connector from the main harness to the run turn brake controller This is ON STEM the input side of the controller and the 8 pin connector will have a RED wire with a YELLOW stripe It should be located on the left side under the passenger handrail PIC 8 Separate this connector place some of the included dielectric grease in each half and plug the 8 Pin Run Turn wiring adapter into each end PIC 8 Proceed to Step 13 NOTE If there is a run turn brake controller installed the wiring adapter needs to be installed upstream in front of the controller The installation order MUST BE main harness from front of bike then the 8 Pin wiring adapter then the controller finally the taillight harness LIGHTED MIRROR STEM COVERS INSTALLATION cont Kuryakyn STEP 8 On 95 and earlier models and any model without 8 Pin main harness AMP connectors Cut the two pigtails with the three pin connectors from the supplied wiring adapter as close to the connection point as possible PIC 9 The remaining 8 Pin Connectors and harness will not be used Continue to Step 8 STEP 8 Using wire strippers remove a small amount of insulation from the cut ends of the wires Insert the exposed end of each wire into an included insulated male spade connector and crimp the end Make sure that the wire is secure in the spade MAKE SURE STEP 9 Remove the seat and locate the H D main wiring harness ae i n n ar WIR
Download Pdf Manuals
Related Search