*** NO SMOKING – ALLOW ENGINE TO COOL
Contents
1. Sa RACING f PERFORMANCE PRODUCTS amp ACCESSORIES Fuel Pressure Regulator Kit PART RS12050 RRFPR 07 APPLICATION S 07 amp Older 215hp Sea Doo Models NO SMOKING ALLOW ENGINE TO COOL COMPLETELY Required tools Part 1 4 Drill Bit N A 1 2 Drill Bit N A 19mm Combo Wrench N A 6mm Allen Wrench N A Oetiker Pliers C 48550347 Start Hex Bit Set RS35187 Recommended tools Part OEM Service Manual Please Call We strongly recommend the use of a service manual to familiarize yourself with the various components and procedures involved with this installation Please note that some of the original clamps hoses and hardware removed in the disassembly process will be used in the installation process These instructions have been written in point form and refer to illustrations Please follow these step by step instructions and illustrations carefully NOTE These installation instructions are broken up into 2 sections The fuel pressure regulator is set at 60psi and configured for rising rate Due to variances in weather and altitude you must verify pressure is at 60psi when craft is running To adjust fuel pressure see page 4 of these installation instructions Section 1 outlines the installation process for the complete kit on all 2007 and older Sea Doo 215hp models The kit is configured for rising rate at 1 to 1 with a base setting of 60psi The supplied vent fitting WILL NOT be used To adjust fuel pressur2. e setting see page 4 of these installation instructions Section 2 outlines the modifications for rising rate configuration and how to adjust the base setting To adjust fuel pressure setting see page 4 of these installation instructions Should you choose to configure the kit for static fuel pressure replace the barbed fitting on the regulator with the supplied vent fitting Word doc RS12050 RRFPR 08 H1 3 24 10 1 SECTION 1 INSTALLATION INSTRUCTIONS Remove seats RXP models remove engine cowling 5 bolts Remove glove box by unsnapping clips 2 at edge closest to seat 1 RXT GTX SC RXP must remove hood cowling clips Pry away from glove box carefully Remove air inlet hoses to gain access to top of fuel tank Word doc RS12050 RRFPR 08 H1 3 24 10 Remove clip securing stock fuel pressure regulator to top of fuel pump Remove fuel pressure regulator by lifting upward It may be necessary to pry apart Take care not to damage top of fuel pump NOTE Keep a shop rag handy to prevent fuel spill Place fuel pressure regulator on a shop rag Disconnect fuel supply hose connector by squeezing clips 2 together while pulling on hose NOTE Cover fuel supply hose connector with a shop rag to prevent fuel spill Remove supply hose connecting clip from stock fuel pressure regulator At front of engine compartment opening measure and mark two spots exactly 1 7 16 apart Ma
3. enter of boss on intake manifold that was under right edge of ECU mounting bracket Install one end of supplied vacuum hose onto boss and secure with supplied small zip tie Route hose forward along wiring harness to fuel pressure regulator Install open end onto barbed fitting on fuel pressure regulator and secure with supplied small zip tie Craft equipped with a Blow off Valve Splice supplied T fitting into vacuum line and secure with supplied small zip ties Connect T fitting to fuel pressure regulator using supplied vacuum hose and secure using supplied small zip ties Fuel Pressure Setting Instructions amp Guide The fuel pressure regulator is set at a static 60psi Due to variances in weather and altitude you must verify pressure is at 60psi when craft is running In the Rising Rate configuration pressure is raised at a ratio of 1 1 Fuel pressure increases 1 pound for every 1 pound of boost 1 Using a 3 16 allen wrench secure adjustment screw Word doc RS12050 RRFPR 08 H1 3 24 10 N Using a 9 16 combo wrench loosen the jam nut securing the adjustment screw Hook craft up to flush kit Start crafts engine and allow to idle Start water flowing to flush kit To increase fuel pressure slowly rotate adjustment screw clockwise To reduce slowly rotate counter clockwise Tighten jam nut Rev engine up 2 3 times and allow to return to idle Verify gauge is reading desired pres
4. n or use of this product No other warranty express or implied including but not limited to the implied warranties of merchantability and fitness for a particular purpose applies Various states do not allow for the limitation of incidental or consequential damages and therefore the above exclusion or limitation may not apply to you Warranty does not include the expenses related to freight or transportation of parts or compensation for any inconvenience or loss of use while being repaired A copy of the original invoice and a Return Authorization Number RA must accompany all warranty claims Warranted replacement parts will be returned freight collect
5. rk first spot 2 1 4 away re a 5 a oid 3 oy pit sa pee y A a SRE Aa Te NEN a ee ENANOS TET EEIPITI ETTET et t VjAgajag eas Hee ARS i i i MM W ii 5 reer vg i l pi Ba i i J i Die oh ii ip w nN yer 2i Va 4 Ba 0 n L mN E E g RXP Mark first spot 2 1 4 to the left of engine cowling bolt hole center RXT GTX SC Mark spots in center of engine compartment flange Drill 1 4 holes in center of flat area se ae ie Using supplied hardware M6 bolts washers amp nuts mount fuel pressure regulator aienea a A 2 Word doc RS12050 RRFPR 08 H1 3 24 10 Install the fuel supply hose connector clip onto the fitting on left side of RIVA Fuel Pressure Regulator Connect the stock fuel hose from motor to the fitting making sure it is securely snapped into place Apply a thin coat of engine oil to o rings on billet fuel supply return manifold Install into top of fuel pump so that brass fittings with hoses face right side of craft Replace clip making sure it is securely snapped into place Secure hoses to steering cable using supplied medium zip tie SECTION 2 RISING RATE MODIFICATIONS Craft NOT equipped with a Blow off Valve Disconnect ECU electrical connectors 2 Remove bolts 4 securing ECU to mounting bracket Remove bolts 4 securing ECU mounting bracket to intake manifold Using supplied 3 32 drill bit slowly drill into c
6. sure 9 Turn water off 10 Turn engine off aS 2 INCREASE i DECREASE Remember the water belongs to everyone Please ride responsibly and respect the environment Technical Support For answers to questions regarding installation or trouble shooting RIVA Performance Products contact RIVA Technical Support directly at 954 247 0705 or by e mail at tech_support rivamotorsports com Limited Warranty RIVA Fuel Pressure Regulator Kits carry a 6 month limited warranty to the original purchaser They are warranted to be free of defects in materials and workmanship under normal use and service Customer modified components will be void of warranty This warranty is limited to defects in the primary components only Finish and or wear marks in or on primary components are not covered under this warranty RIVA Racing s liability is expressly limited to the repair or replacement of the components contained within or associated with this kit RIVA Racing agrees to repair or at RIVA s option replace any defective unit without charge if product is returned to RIVA Racing freight prepaid within the warranty period Any equipment returned which in RIVA s opinion has been subjected to misuse abuse overheating or accident shall not be covered by this warranty RIVA Racing shall have no liability for special incidental or consequential damages or injury to persons or property from any cause arising from the sale installatio
Download Pdf Manuals
Related Search