GU MP4124 - Dultmeier Sales
Contents
1. L 1 e 1 al 00 600 800 4000 1200 Pump RPM 200 3 The discharge plumbing from the pump should be properly sized to the flow rate to pre vent line pressure loss to the work area Itis essential to provide a safety bypass valve be tween the pump and the work area to protect the pump from pressure spikes in the event of a blockage or the use of a shut off gun 4 Use of a dampener is necessary to mini mize pulsation at drive elements plumbing connections and other system areas The use of a dampener with Giant Industries Inc pumps is optional although recommended by Giant Industries Inc to further reduce system pulsation Dampeners can also reduce the severity of pressure spikes that occur in sys tems using a shut off gun A dampener must be positioned downstream from the unloader 5 Crankshaft rotation on Giant Industries Inc pumps should be made in the direction desig nated by the arrows on the pump crankcase Reverse rotation may be safely achieved by following a few guidelines available upon request from Giant Industries Inc Required horsepower for system operation can be ob tained from the charts on page 3 6 Before beginning operation of your pumping system remember Check that the crankcase and seal areas have been properly lubricated per recommended schedules Do not run the pump dry for extended periods of time Cavita tion will result in seve2. 25 as described on page 9 REPAIR INSTRUCTIONS MP SERIES 15 Replace the rear support ring 35A for MP4120W MP4124W and 41 for MP4130W MP4135W Replace the rear v sleeve 35B for MP4120W MP4124W and 40 for MP4130W MP4135W and rear pressure ring 35C for MP4120W MP4124W and 39 for MP4130W MP4135W making sure that the grooved side is facing the discharge end of the manifold 43 For MP4120W MP4124W replace the rear o ring 35D into the back of the manifold 43 Replace the snap ring 36 16 Reinstall the pressure ring 39 v sleeve 40 40A fpr MP4135W support ring 41 40 for MP4135W and intermediate ring 41A into each plunger bore Re install the tension spring 42 For MP4120W MP4124W only replace the spacer ring 52A 40A in E zk in MP4135W 17 Reassemble the inlet valve assembly in the reverse order of step 6 Make certain all the components are press fit together and that the spring retainer 54 is slightly counter sunk in the valve housing 52 Grease the o ring 53 and replace it on to the valve housing Reinstall the entire inlet valve assembly into the manifold 43 Replace the tension plugs 42A and tighten 18 Reassemble the discharge valve assembly by placing the valve plate 45 spring 46 and spring retainer 47 on top of the valve seat 44 Press fit together Place the entire discharge assembly into discharge port making certain the assembly is proper
3. 11 295 EE A154 e005 1100 ws 180 12 295 Intermittent rating of 2000 PSI Metric Measurements Be e ee Pressure Speed Req d Temperature Diameter Required Modei Umin Bar RPM kw c m ms MP4135 512 130 100 136 7 23 9 MP4130 582 1o 1100 131 7 30 9 Mm 58 2 110 1100 131 90 30 Na Intermittent rating of 140 Bar Consult the factory for special requirements that must be met if the pump is to operate beyond one or more of the limits specified above Horsepower Ratings We recommend a 1 15 service factor be specified when selecting an electric motor as the power source To compute electric motor horsepower required use the following formula HP GPM X PSI 1450 The formula to determine the horsepower required for a gas engine is HP GPM X PSI 1150 The formula to determine the horsepower required for a diesel engine is HP GPM X PSI 1250 For the Application of a Hydraulic Motor To Determine the Torque of a Hydraulic Motor GPM x PSI x 36 77 RPM Torque in lbs Calculating RPM GPM of Pump A pump must be connected to an electric motor or gas or diesel engine with the correct ratio of pulleys and belts to attain the required speed and GPM The use of a Variable Frequency Drive VFD may also be used to control the RPM of a properly sized electric motor when variable flows are required Max Pump RPM Rated Pump GPM x
4. DAMAGES OR EXPENSES INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES DIRECTLY OR INDIRECTLY ARISING FROM THE SALE OR USE OF THIS PRODUCT THE LIMITED WARRANTY SET FORTH HEREIN IS IN LIEU OF ALL OTHER WARRANTIES OR REPRESENTATION EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION ANY WAR RANTIES OR MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE AND ALL SUCH WARRANTIES ARE HEREBY DISCLAIMED AND EXCLUDED BY THE MANUFACTURER GIANT INDUSTRIES INC 900 N Westwood Ave Toledo Ohio 43607 PHONE 419 531 4600 FAX 419 531 6836 www giantpumps com Copyright 2012 Giant Industries Inc 06 12 MP Series indd
5. Spring Retainer Inlet Disc for Crankshaft 09062 Description O Ring Tension Plug O Ring Tension Plug Valve Seat O Ring Valve Seat Valve Plate Valve Spring O Ring O Ring Spring Retainer SE Discharge Valve Assembly Kit 09043 Item 42B 44 Part 07332 07280 07281 07282 07283 07284 Description O Ring Tension Plug Valve Seat O Ring Valve Plate Valve Spring Spring Retainer woo wo og PHP WBWWWWWWWHANAWWWWWWHDHDD A Ww WWWWWW vaovewaoacl lt MALFUNCTION The Pressure and or the Delivery Drops Water in crankcase Noisy Operation Rough Pulsating Operation with Pressure Drop Pressure Drop at Gun Excessive Leakage High Crankcase Tem perature PUMP SYSTEM MALFUNCTION CAUSE Worn packing seals Broken valve spring Belt slippage Worn or Damaged nozzle Fouled discharge valve Fouled inlet strainer Worn or Damaged hose Worn or Plugged relief valve on pump Cavitation Unloader High humidity Worn seals Worn bearings Cavitation Worn packing Inlet restriction Accumulator pressure Unloader Cavitation Restricted discharge plumbing Worn plungers Worn packing seals Excessive vacuum Cracked plungers Inlet pressure too high Wrong Grade of oil Improper amount of oil in crank case REMEDY Replace packing seals Replace spring Tighten or Replace belt Replace nozzle Clean valve assembly Clean strainer Repair Replace hose Clean Reset and
6. B 42B 43 43 44 44A 45 46 46A 47 48 48 48A 49 49A 50 50A 51 52 52 52A 53 53 53A 54 57 Inlet Valve Assembly Kit Item 42B 42B 06083 07272 05687 06137 07272 07270 06084 07273 06652 07329 07274 07275 07353 06102 06103 07332 07354 06104 06105 07280 07281 07282 07283 06959 07284 06108 07356 07332 06109 07319 07158 07159 06110 06111 06112 07329 12057 07332 12027 06115 13020 Part 07354 07332 07280 07281 07282 06959 12057 12027 06115 V Sleeve MP4124W V Sleeve MP4130W V Sleeve MP4135W V Sleeve MP4130HkK V Sleeve MP4130HkK Support Ring MP4120W Support Ring MP4124W Support Ring MP4130W Support Ring MP4135W Spacer MP4120W MP4124W Intermediate Ring MP4130W MP4135W Tension Spring MP4120W MP4124W Tension Spring MP4130W MP4135W Tension Plug MP4120W MP4124W Tension Plug MP4130W MP4135W O Ring MP4120W MP4124W O Ring Tension Plug MP4130W MP4135W Manifold Head MP4120W MP4124W Manifold Head MP4130W MP4135W Valve Seat O Ring Valve Seat Valve Plate Discharge Valve Spring Inlet Valve Spring Spring Retainer Discharge Plug S S MP4120W MP4124W Plug Brass MP4130W MP4135W O Ring Plug Stud Manifold Shim Stud Nut Manifold Stud Spring Washer Spacer Valve Housing MP4120W MP4124W Valve Housing MP4130W Spacer Ring MP4120W O Ring MP4120W MP4124W O Ring MP4130W O ring MP4120W
7. MP Series Triplex Ceramic Plunger Pump Operating Instructions Repair and Service Manual Pump Models MP4120 MP4124 MP4135 MP4130 MP4130HK Z Contents Updated 6 12 Installation Instructions page 2 Pump Specifications page 3 Exploded View page 4 Parts List Repair Kits page 5 Trouble Shooting page 6 Repair Instructions page 7 11 Torque Specifications page 11 Dimensions page 11 Warranty Information back page INSTALLATION INSTRUCTIONS Installation of the Giant Industries Inc pump is not a complicated procedure but there are some basic steps common to all pumps The following information is to be considered as a general outline for instal lation If you have unique requirements please contact Giant Industries Inc or your local distributor for assistance 1 The pump should be installed flat on a base to a maximum of a 15 degree angle of inclination to ensure optimum lubrication 2 The inlet to the pump should be sized for the flow rate of the pump with no unneces sary restrictions that can cause cavitation Teflon tape should be used to seal all joints If pumps are to be operated at temperatures in excess of 160 F it is important to insure a positive head to the pump to prevent cavita tion See chart below 9 29 5 LE Clee H ke i H 7 23 0 A mi 6 19 7 T Si 5 16 4 Se NPSHR Meters Feet Head of Water 4 nau
8. Replace worn parts Check suction lines on inlet of pump for restrictions Check for proper operation Reduce oil change interval Replace seals Replace bearings Refill crankcase oil with recommended lubricant Check inlet lines for restrictions and or proper sizing Replace packing Check system for stoppage air leaks correctly sized inlet plumbing to pump Recharge Replace accumulator Check for proper operation Check inlet lines for restrictions and or proper size Re size discharge plumbing to flow rate of pump Replace plungers Adjust or Replace packing seals Reduce suction vacuum Replace plungers Reduce inlet pressure Giant oil is recommended Adjust oil level to proper amount REPAIR INSTRUCTION MP SERIES Disassembly sequence of the GIANT MP Series Pumps 1 With a 27mm wrench re 2 Inspect the plug o rings 3 From the discharge port remove move the three discharge 48A and 42B and the spring retainer 47 plugs 48 and three inlet replace as necessary spring 46 and the valve plate plugs 42A from the 45 Using the valve puller manifold 43 Available from Snap On Tools remove the valve seat 44 SC Zeen Remove the six manifold stud nuts 4 Inspect all parts especially the seating surface 2 of the valve plate 45 and replace as neces 50 with a 19mm wrench Re sary move the spring washers 50A Tap the back of the manifold with a rubber mallet to dislodg
9. Required Pump GPM Required Pump RPM To calculate a pulley diameter one 1 pulley diameter and the required pump RPM must be known Pump RPM x Pump Pulley Diameter Motor RPM Motor Pulley Diameter Motor RPM x Motor Pulley Diameter Pump RPM Pump Pulley Diameter Common Specifications Materials Used for MP Pumps Inlet Pressure 145 PSI 10 Bari Manifold Aluminum Bronze Crankshaft Diameter 1 10 28mm Plungers Solid Ceramic Oxide Crankcase Oil Capacity 32 fl oz 1 0 L Valves High Grade Stainless Steel Inlet Ports Seals Nitrile with Fabric Reinforcing Discharge Ports 2 3 4 NPT Gear End Spheroidal Cast Iron STOKE gp coneinccndcrnasacasnicevsnasnsanse 1 02 26mm 66 Ibs 30kg Top of Pulley Toward Fluid End Exploded View MP Series In MP4130HK Only This is item 40A In MP4130HK Only This is item 40 MP SERIES PARTS LIST AND REPAIR KITS ITEM PART DESCRIPTION ITEM PART DESCRIPTION 1 06100 Crankcase 2 13000 Oil Filler Cap Assembly 4 07243 Cover Crankcase 5 07244 O Ring Crankcase Cover 8 01008 Oil Dip Stick 9 01009 O Ring Dip Stick 10 01010 Screw Crankcase Cover 11 01011 0400 Spring Washer 12 07109 Oil Drain Plug 13 07182 Gasket Oil Drain Plug 14 07245 Bearing Cover 15 07247 Seal Crankshaft 16 07627 O Ring Bearing Cover 17 07114 Hex Screw Bearing Cover 20 07248 Roller Bearing Tapered 20A 07249 Shim 20B 06962 Fitting Disc 21 07250 Shaft Prot
10. aring cover on the crankcase 1 and insert the cover bolts 17 Tighten the cover evenly to the crankcase setting the bearing into position Torque the cover bolts to 125 inch pounds 14 Nm 10 REPAIR INSTRUCTIONS MP SERIES Reassembly Sequence 36 37 38 39 40 41 Insert the crankshaft 22 with the mounted bearings 20 through the near side of the crankcase 1 Make certain that the numbers or colors or the crankshaft correspond to the numbers or colors on the connecting rods 24 Reinstall the near side bearing race by inserting it into the crankcase Supporting the crankshaft with one hand tap the race with a rubber mallet until the edge is flush with the crankcase Replace any shims 20A 20B and position the bearing cover 14 as before Tighten the bearing cover bolts 17 evenly to position the bearing race Torque the bolts to 125 inch pounds Once the crankshaft reassembly is complete oil the crankshaft races freely before replacing the connecting rod 24 end caps Reassemble the connecting rods 24 matching the numbered or colored halves Torque the con necting rod bolts 24A to 250 inch pounds 28 Nm To replace the oil seal 31 apply Locktite to the outside edges of the seal and install from the front of the crankcase 1 The side of the seal with the spring must face the oil Make sure that the face of the seal is flush with the crankcase Clean the back edge of th
11. e and slide it off the studs 49 The spacer 51 can now be removed by pry ing gently outward with a screw driver through the front of the inlet port 6 To remove the inlet valve assembly insert a 13mm socket with extension through the rear of the inlet manifold 43 port and tap it firmly with a 7 Pull the inlet valve assembly apart for inspection Any resis hammer This will force tance may be overcome by placing the valve housing 52 in the tension spring 46A a brass jawed vise and carefully tapping the back of the valve valve housing 52 and plate 45 with a screwdriver Inspect the valve seats 44 the remainder of the inlet spring 46A o ring 44A and o ring 53A for MP4120W valve assembly out through MP4124W for wear and replace them as necessary the front of the inlet port REPAIR INSTRUCTION MP SERIES 8 From the front of the manifold 9 Turn the manifold 43 over and remove the rear v sleeve 43 remove the packing as snap ring 36 For MP4120W MP4124W remove the sembly 41A 41 40 and 39 rear o ring 35D Remove the rear pressure ring 35C Use a small slide hammer puller MP4120W MP4124W amp 39 MP4130W MP4135W rear if necessary or insert a wooden v sleeve 35B MP4120W MP4124W A 40 MP4130W dowel through the back of the MP4135W and rear support ring 35A MP4120W manifold and tap the assembly MP4124W amp 41 MP4130W MP4135W These parts out from the back to the fr
12. e crankcase and replace the crankcase cover 4 be careful not to pinch the crankcase cover o ring 5 Fill the crankcase with 32 fluid ounces of Giant oil or the equivalent SAE 85W 140 Industrial Gear oil and check the oil level with the dip stick 8 The proper level is center of the two lines Reinstall the Giant MP Series pump into your system MP SERIES TORQUE SPECIFICATIONS Position Item Description Torque Amount in lbs Nm 17 07114 Hex Screw Bearing Cover 125 14 24 07253 Hex Screw Connecting Rod 250 28 29C 13007 Bolt Plunger 300 34 50 07158 Nut Manifold Stud 700 79 MP SERIES DIMENSIONS Inches mm 0 3 a Vas 1Wide HB Ce ko S 8 0005 0000 Inlet 1 NPT NOTE Contact Giant Industries for Service School Information Phone 419 531 4600 11 GIANT INDUSTRIES LIMITED WARRANTY Giant Industries Inc pumps and accessories are warranted by the manufacturer to be free from defects in workmanship and material as follows Te For portable pressure washers and self service car wash applications the dis charge manifolds are guaranteed for the life of the pump Our other pump parts used in portable pressure washers and in car wash applications are warranted for five years from the date of shipment for all pumps used in NON SALINE clean water applications 2 One 1 year from the date of shipment for all other Giant industrial and consumer pumps 3 Six 6 months from the da
13. ector 22 07251 Crankshaft 23 07252 Key 24 07253 Connecting Rod 25 07596 Crosshead Complete 28 07255 Crosshead Pin 29A 07256 Centering Sleeve 29B 07262 Ceramic Plunger 20mm MP4120W 29B 13046 Ceramic Plunger 24mm MP4124W 29B 07261 Ceramic Plunger 30mm MP4130W MP4130HK 29B 13005 Ceramic Plunger 28mm MP4135W 29C 13007 Bolt Sold only w 07258 29D 07258 Seal Washer 30 06136 Flinger 31 07260 Crankcase Oil Seal 35A 07263 Rear Support Ring MP4120W 35A 06079 Rear Support Ring MP4124W 35B 06064 Rear V Sleeve MP4120W 35B 06080 Rear V Sleeve MP4124W 35C 07265 Rear Pressure Ring MP4120W 35C 06081 Rear Pressure Ring MP4124W 35D 07266 Rear O Ring MP4120W 36 07267 Snap Ring 39 07268 Pressure Ring MP4120W 39 06082 Pressure Ring MP4124W 39 07271 Pressure Ring MP4130W 39 13013 Pressure Ring MP4135W 40 07322 V Sleeve MP4120W Plunger Packing Kits MP4120W 09044 ltem Part Description Qty 40 07322 V Sleeve 3 35B 06064 Rear V Sleeve 3 MP4124W 09300 ltem Part Description Qty 40 06083 V Sleeve 3 35B 06080 Rear V Sleeve 3 MP4130W 09042 Item Part Description Qty 40 07272 V Sleeve 6 MP4135W 09665 ltem Part Description Qty 40 05687 V Sleeve 6 MP4130HK 09664 Item Part Description Qty 40 06137 V Sleeve High Temp 6 40A 07272 V Sleeve 3 QTY WADWBWWWWWWWWWWWWWW WWWWWWWAAANNNONNNAHAAHAAAAB Aa 40 40 40 40 40A 41 41 41 41 41A 41A 42 42 42A 42A 42
14. he near side race will remain in the crankcase The roller bearings 20 will remain on the crankshaft When both ends are free the crankshaft can be removed by hand To remove the remaining bearing race place a dowel against the inside edge of the race and tap it out with a rubber mallet This is done only if the race wear surface has been damaged Inspect the bearing race removed with the crankshaft 22 and replace if wear surface is damaged Note The following procedure is only necessary if the inspection shows evidence of heavy wear Inspect the crankshaft 22 and bearings 20 for wear To remove the roller bearings from the crankshaft use a three inch push puller with a pulley attachment To remount the bearings tap the bearings down the well lubricated crankshaft with the Giant Bearing Tool Be sure that the bearing is firmly seated Remove the connecting rod 24 with the attached crosshead plunger assembly 25 from the crankcase 1 by pulling it straight out The oil seals 31 may now be removed by tapping them out through the front of the crankcase Be careful not to damage the snap ring Inspect the surfaces of the crosshead plunger assembly 25 and connecting rods 24 for heavy scoring or galling due to poor lubrication Check for play at the joint between connecting rod cross head plunger assembly To remove the crosshead pin 28 from the crosshead plunger assembly 25 the assembly should be positioned in
15. ly seated Replace discharge plug 48 and tighten securely 19 Again lubricate the plungers 29B and slide the manifold 43 gently and evenly over the plungers Press the manifold firmly into place against the crankcase 1 Replace the spring washer 50A and tighten the manifold stud nuts 50 to 700 inch pounds 79 Nm REPAIR INSTRUCTIONS MP SERIES Gear End Disassembly 20 21 22 23 24 25 26 27 26 29 30 Remove the manifold and plunger assemblies as described earlier Make sure the oil is drained from the pump before removing the crankcase cover 4 Remove all screws 10 Inspect the crankcase cover o ring 5 for damage and replace it as necessary Remove the connecting rod screws and washers with a 6mm allen wrench Remove the back halves of each connecting rod 24 Push the connecting rods down as far as possible into the crankcase 1 housing Note that the connecting rod halves are numbered or colored and that the numbers or colors must be matched for reassembly Remove the crankshaft bearing cover screws 17 with a 13mm wrench Remove the key 23 from the crankshaft 22 Remove the bearing cover 14 and any shims 20A if any Remember to replace shims on the same side of the crankcase 1 during the reassembly Steady the pump rear assembly and using a rubber mallet tap the crankshaft 22 from one side The far side bearing race will be removed and t
16. ont should slide out with little resistance If necessary a screwdriver may be used to pry outward Replace all rub ber parts and inspect the metal parts for wear 10 Note The following pro cedure is only necessary if a stud bolt 49 has been damaged and must be replaced To remove the manifold studs 49 place a stud nut 50 lock washer 50A and second nut on each stud Tighten the nuts against each other Hold the front nut with one wrench and 11 Inspect ceramic plunger pipe 29B Clean any dirt or remove the stud bolt by grime If the surface of the pipe is rough scored or pitted turning the rear nut coun replace plunger pipe To remove the ceramic plunger terclockwise with another pipe turn the plunger bolt 29C counterclockwise with wrench To reassemble a 13mm socket Use a steady torque to prevent ceramic turn the front stud bolt nut plunger pipe damage Loosen and remove the plunger clockwise bolt assembly 29C and 29D and replace the seal washer 29D i d g s S 12 Inspect the crankcase oil 13 Clean the bolt threads 14 Torque the ceramic plunger seals 31 for evidence of 29C apply locktite bolt assembly to 300 inch leaking If there is oil on and remount pounds 34 Nm If originally the crankcase 1 at the removed reinstall the stud sight of the oil seals they bolts 49 must be replaced The oil seals are replaced after removing the crosshead plunger assembly
17. re damage Always re member to check that all plumbing valves are open and that pumped media can flow freely to the inlet of the pump Finally remember that high pressure operation in a pump system has many advantages But if it is used carelessly and without regard to its potential hazard it can cause serious injury IMPORTANT OPERATING CONDITIONS Failure to comply with any of these conditions invalidates the warranty 1 Prior to initial operation add oil to the crank case so that oil level is between the two lines on the oil dipstick DO NOT OVERFILL Use SAE 85W 140 Industrial Gear Oil Giant s p n 01154 Crankcase oil should be changed after the first 50 hours of operation then at regular inter vals of 500 hours or less depending on operating conditions 2 Pump operation must not exceed rated pres sure volume or RPM A pressure relief device must be installed in the discharge of the system 3 Acids alkalines or abrasive fluids cannot be pumped unless approval in writing is obtained before operation from Giant Industries Inc 4 Run the pump dry approximately 10 seconds to drain the water before exposure to freezing temperatures MP SERIES PUMP SPECIFICATIONS U S Measurements Pressure Speed Req d Temperature Diameter Required ES RPM He L E Deeg Model 1 GPM MP4120 i2 3625 1450 0 787 meaa 128 210 1450 24 160 ogs 279 pai35 135 1885 1100 182 i160
18. such a manner to prevent damage to the crosshead when driving the pin out The crosshead pin can be driven out by tapping on the tapered side of the pin Reassembly Sequence Note Always take time to lubricate all metal and nonmetal parts with a light film of oil before reassem 31 bly This step will help ensure a proper fit at the same time it will protect the pump non metal parts elastomers from cutting and scoring Take the crosshead plunger rod assembly and insert the connecting rod 24 into the crosshead plunger assembly 25 Drive the tapered end of the crosshead pin 28 into the beveled side of the crosshead and through the connecting rod completing the assembly Note The crosshead pin should not extend beyond either side of the crosshead in order to prevent dam 32 33 34 35 age to the crosshead bore of the crankcase Inspect the crankcase crosshead guides for any possible damage Replace the connecting rod 24 crosshead plunger rod assembly 25 into the crankcase 1 If removed previously replace the far side bearing race into the crankcase Tap with a rubber mallet until the edges are flush with the crankcase surface Remove the old crankshaft seal 15 from the bearing cover 14 Lubricate the edges of the new seal and install using the standard Giant Bearing Tool Remove the bearing tool and tap around the perimeter of the seal with a rubber mallet to firmly seat the seal Position the far be
19. te of shipment for all rebuilt pumps 4 Ninety 90 days from the date of shipment for all Giant accessories This warranty is limited to repair or replacement of pumps and accessories of which the manufac turer s evaluation shows were defective at the time of shipment by the manufacturer The follow ing items are NOT covered or will void the warranty 1 Defects caused by negligence or fault of the buyer or third party Normal wear and tear to standard wear parts Use of repair parts other than those manufactured or authorized by Giant Improper use of the product as a component part Changes or modifications made by the customer or third party The operation of pumps and or accessories exceeding the specifications set forth in the Operations Manuals provided by Giant Industries Inc Dm Fab Liability under this warranty is on all non wear parts and limited to the replacement or repair of those products returned freight prepaid to Giant Industries which are deemed to be defective due to workmanship or failure of material A Returned Goods Authorization R G A number and completed warranty evaluation form is required prior to the return to Giant Industries of all prod ucts under warranty consideration Call 419 531 4600 or fax 419 531 6836 to obtain an R G A number Repair or replacement of defective products as provided is the sole and exclusive remedy pro vided hereunder and the MANUFACTURER SHALL NOT BE LIABLE FOR FURTHER LOSS
Download Pdf Manuals
Related Search