X31N
Contents
1. Max No of occupants Standard 3 people 4 people 4 people 3 people on Extension 1 person 1 person 1 person 1 person Height Working Height 26 ft 7 9 m 26 ft 7 9 m 32 ft 9 75 m 37 ft 11 28 m Max Platform Height 20 ft 6 1 m 20 ft 6 1 m 26 ft 7 92 m 31 ft 9 44 m Min Platform Height 38 in 97 m 39 in 99 m 43 in 1 09 m 43 in 1 09 m Dimensions Weight 3 828 lbs 1656 kg 4 273 lbs 1858 kg 4 747 lbs 2072 kg 5430 lbs 2463 kg Overall Width 32 in 83m 48 in 1 22 m 48 in 1 22 m 48 in 1 22 m Overall Height 78 in 1 98m 79 in 2 0 m 83 in 2 11 m 83 in 2 11 m Overall Length 92 in 2 34m 92 in 2 34 m 92 in 2 34 m 92 in 2 34 m Driveable Height 20 ft 6 1 m 20 ft 6 1 m 26 ft 7 93 m 31 ft 7 93 m Surface Speed Platform Lowered 0 to 2 3 mph 0 to 3 70 km h 0 to 2 3 mph 0 to 3 70 km h 0 to 2 3 mph 0 to 3 70 km h 0 to 2 3 mph 0 to 3 70 km h Platform Raised 0 to 7 mph 0 to 1 13 km h 0 to 7 mph 0 to 1 13 km h 0 to 7 mph 0 to 1 13 km h 0 to 7 mph 0 to 1 13 km h Energy Source 24 Volt Battery Pack 4 220 Amp 24 Volt Battery Pack 4 220 Amp 24 Volt Battery Pack 4 220 Amp 24 Volt Battery Pack 4 220 Amp Hour 6 Volt Batteries min wt Hour 6 Volt Batteries min wt Hour 6 Volt Batteries min wt Hour 6 Volt Batteries min wt 62 lbs each 28 12 kg 4 HP 62 lbs each 28 12 kg 4HP 62 Ibs each 28 12 kg AHP 62 lbs eac2. UY cC O pur Q Pe UY lt O C pur 0 Q O cC 0 Y O CC ar aj 0 tan U
3. oil leaks damaged cables or hoses loose connections damaged or missing labels and tire damage 8 Move machine if necessary to unobstructed area to allow for full elevation 9 Turn Chassis and Platform Emergency Stop Switches ON Figure 1 amp 2 by pulling the button out 10 Turn the Chassis Key Switch Figure 1 to CHASSIS 11 Push Chassis Lift Switch Figure 1 to UP position and fully elevate platform 12 Visually inspect the elevating assembly lift cylinder cables and hoses for damage or erratic operation Check for missing or loose parts Control K Key Switch Chassis Lift el witc ld BS umeter gt QU VpRight en Chassis Pot Hole em Emergency Support Stop Switch Figure 1 Chassis Left Side 13 Verify that the Depression Mechanism Sup ports have rotated into position under each module 14 Partially lower the platform by pushing Chassis Lift Switch to DOWN and check operation of the audible lowering alarm 15 Open the Chassis Emergency Lowering Valve Figure 3 to check for proper operation by pulling and holding the knob out Once the platform is fully lowered close the valve by releasing the knob 16 Turn the Chassis Key Switch to DECK 17 Close and latch the module doors 18 Check that route is clear of persons obstruc tions holes and drop offs is level and capable of supporting the wheel loads 19 Unhook Controller from guardrail Firmly grasp Controller while performi
4. will not operate under its own power and it is necessary to move the machine or when towing the machine up a grade or winching onto a trailer to transport Note X31N models have two identical brake adjustment nuts located on both sides of the ladder The Brake Adjustment Release Nut s is are located at the rear of the machine to the right and left of the ladder 1 To release the brakes tum the nut s counterclock wise until the brakes disengage from the tires 2 The machine will now roll when pushed or pulled 3 To reset the brakes turn the nut s clockwise until the brakes have fully engaged the tires Test the brakes on a 23 slope before return ing the machine to service A WARNING A Never operate work platform with the Parking Brakes released Serious injury or damage could result Never tow faster than 1 ft sec 3m sec V V A ADA DI A p pu pp pp p pa Figure 4 Parking Brake Release X31N Shown wasa A a ERAS sap 1 2 7 lt Y A AN wu N ee q Mur 7 jr A a gm a 4 fe wo gt Die a ae as AS et un En After Use Each Day 1 2 Ensure that the platform is fully lowered Park the machine on level ground preferably under cover secure against vandals children or unauthorized operation Turn the Key Switch to OFF and remove the key to prevent unauthorized operation Transporting Work Platform By Forklift NOTE Forklifting is for transporting only A
5. 381 mm Diameter Solid Rubber non marking Rubber non marking Rubber non marking Rubber non marking Parking Brake Spring Applied Hydraulic Release Spring Applied Hydraulic Release Spring Applied Hydraulic Release Spring Applied Hydraulic Release Brake with Manual Release Brake with Manual Release Brake with Manual Release Brake with Manual Release Turning Radius 8 in 254 mm Inside 8 in 254 mm Inside 8 in 254 mm Inside 8 in 254 mm Inside Maximum Gradeability 23 13 degrees 23 13 degrees 22 12 degrees 20 11 degrees Wheel Base 74 2 in 1 9 m 74 J in 1 9 m 74 l4 in 1 9 m 74 l in 1 9 m Guardrails 40 in 1 02 m 40 in 1 02 m 40 in 1 02 m 40 in 1 02 m Toeboard 6 in 152 mm High 6 in 152 mm High 6 in 152 mm High 6 in 152 mm High Specifications subject to change without notice Meets or exceeds all applicable requirements of OSHA and ANSI A92 6 1999 Hot weather orheavy use may reduce performance Refer to Service Manual for complete parts and service information FOR MORE INFORMATION UpRight Local Distributor USA TEL 1 800 926 5438 or 1 559 662 3900 FAX 1 559 673 6184 Parts FAX 1 800 669 9884 801 South Pine Street Madera California 93637 http www upright com Europe TEL 353 1 620 9300 FAX 353 1 620 9301 UNIT S1 PARK WEST INDUSTRIAL PARK FRIEL AVENUE NANGOR ROAD 060572 003 DUBLIN 12 IRELAND 06 02 suoljonijsu bunelado pue sajny Ajajes
6. 6 600 cccr LO ANNO DNILYOdSNVYL YO mn 343H L13 7 A9803 3015 JHL OY 1YMLOY WIOALFId 43917 OL INO TINd OSNIYAMOT ADNADYAWS AFHINDF4 1 000 899990 AFHINDIH 2 NLE GO0 0SZ 1010 N9Z 700 0SZ LOL MOZ 00 OSZ LOL NOZ Z00 0SZ LOL DRE LEIDE AM J1dO3dE YO 581 052 IYO T N4OALYIA AFLNGIYLSIG ANIAIX VIN 66 61 9 z6V ISNV 30 SLN3W3UIND3Y SHL 0339X3 YO SLIM AFUHINDF4 1 00 082 190 d34INO38 1 000 0SS990 UHojEld1no aplIg uq 807 087 Pana SE Ae SIIEIDIEn E Sean ug quia LONG pajenaja a SIHYZYH 113 Sduvz AAinlui noes JO Yeap SrIE2 JII sa n Ayayes Bulnolioj ay ago pue puelsi pun pes ol aunjie4 EON NADI El 33983 HOSSISS LIMA W3031V14 ASIVY SWULNO YIMMI ONISN L N9ZX MOZX NOZX qauimnoat L 000 19S990 qauinoaut L LO0 299290 a 3401 HD 591 09 HSM TIH AAA NINE HIV MEE E Sada td OHYZYrH H3AO dLL EDINA AER id 39V301S SNOLLONULSNI JIVUA HOSSIOS AFUHINDFH 1 000 L55500 arut Tenn T3A31 CIONINNOIIY LY FINGOW LHOIY 0103 AYSLLVE NIVINIVA Ad311vg Keme syed poq ije daay OYVZVH SNIHSNYI qaqI nO3d r L00 96S990 AFUHINDF4 1 000 cSS990 2918 40 syede asodxa LON Og 32 13484 Bu bueyo umu PEIEIAUGE SE narsgnjdrsd GSYINDAY e 000 SS990 ONIOIAHIS 340434 SHOSSIDS WOOT N SHOSSIOS s 40 HY312 daa ONI
7. 7 m Rotate Scissors Brace towards the front and allow it to hang vertical over the lower scissor pivot tube 6 Push Chassis Lift Switch to DOWN position and gradually lower platform until brace rests on lower scissor arm pivot tube Removal 1 Push Chassis Lift Switch to UP position and gradually raise platform until the lower end of the Scissors Brace will clear the lower scissor arm pivot tube ah 2 Rotate Scissors Brace towards the rear so that it rests on the cylinder mount stowed position 3 Push Chassis Lift Switch to DOWN position and completely lower platform IS Be Scissors Brace Re gt Te E Figure 7 Blocking Elevating Assembly X20N X20W X26N Blocking Elevating Assembly X31N See Figure 8 Installation 1 Park the work platform on firm level ground 2 Verify both Emergency Stop Switches are ON 3 Turn Chassis Key Switch to CHASSIS 4 Position Chassis Lift Switch to UP and elevate platform approximately nine 9 feet 2 7 m leaving enough room to freely rotate the Scissors Brace 5 Pull out on the retaining pin and rotate the Scissors Brace into vertical position 6 Push Chassis Lift Switch to DOWN position and gradually lower platform until the upper and lower pivot pins rest on the Scissors Brace Removal 1 Push Chassis Lift Switch to UP position and gradually raise platform until the Scissors Brace will clear the pivot pins 2 Rotate the Scissors Brac
8. CAUTION A See specifications for weight of work platform and be certain that forklift is of adequate capacity to lift platform Forklift from the rear of the machine using the forklift pockets provided If necessary the ma chine may be forklifted from the side by lifting under the Chassis Modules By Crane 1 Secure straps to Chassis Lifting Lugs only Figure 5 amp 6 By Truck 1 Maneuver the work platform into transport position and chock wheels 2 Secure the work platform to the transport vehicle with chains or straps of adequate load Capacity attached to the chassis tie down lugs Figure 5 amp 6 A CAUTION A Front tie down lugs are not to be used to lift work platform Overtightening of chains or straps through tie down lugs may result in damage to work platform Figure 5 Parking Brake Release Rear Tie DONAS e Front Tie Downs Lifting Lugs A WARNING A Never perform service on the work platform in the Elevating Assembly area while platform is elevated without first blocking the Elevating Assembly DO NOT stand in Elevating Assembly area while installing or removing brace Blocking Elevating Assembly X20N X20W and X26N See Figure 7 Installation 1 Park the work platform on firm level ground 2 Verify both Emergency Stop Switches are ON 3 Turn Chassis Key Switch to CHASSIS 4 Position Chassis Lift Switch to UP and elevate platform approximately nine 9 feet 2
9. NUUM Y BNUGW UOHONIPsUL u uoyewaopu Apepes ye MOJO Vay pue peal juawdinba sip Gulesado 3940438 AFHINDF4 1 NLE N9Z MOZ 010 09S990 NOZ L L0 09S990 GINA 2rinvuqAH penbe s juewysnipe sodod Mae ay je paysn pe ae s nl n 191191 Pue sayoums ainssald sayay ms UT a34INO34 1 p 000 999990 a diNodd L 000 799990 dOLS AONF39U3N3 AF4HINDF4 1 000 61090 aSU3Adu rea SUOI INIJSU funeladg R sajny AJajes Y NOWNALIV Y AF4HINDF4 1 L00 920010 enuen 991A19S 1Insuo2 suondo YUM paddinba sauiyoew 104 jaqe yoes q pa3 e20 1aquinyn Med Husn Ag paiapj0 aq ued SIB 9 0N THESE LABELS SHALL BE PRESENT AND IN GOOD CONDITION BEFORE OPERATING THE WORK PLATFORM BE SURE TO READ UNDER X SERIES LABEL INSTALLATION STAND AND FOLLOW THESE LABELS WHEN OPERATING THE WORK PLATFORM NOTES 10 NOTES 11 Specifications ITEM X20N X20W X26N X31N Platform Size 28 in x 87 in 711 mm x 2 21 m 44 in x 87 in 1 12 m x 2 21 m 44 in x 87 in 1 12 m x 2 21 m 44 in x 87 in 1 12 m x 2 21 m w Extension Inside Toeboards Inside Toeboards Inside Toeboards Inside Toeboards Max Platform Capacity Standard w Extension 750 lbs 340 kg 1000 Ibs 453 kg 1000 Ibs 453 kg 700 lbs 318 kg on Extension 250 lbs 110 kg 250 lbs 110 kg 250 lbs 110 kg 250 lbs 110 kg
10. UpRight Operator Manual X Series SERIAL NO 13600 to Current NEVER operate the machine NEVER elevate the platformor NEVER sit stand or climb on within ten feet of power lines drive the machine while el guardrail or midrail THIS MACHINE IS NOT IN evated unless the machine is SULATED on firm level surface NEVER operate the machine without first surveying the work area for surface hazards such as holes drop offs bumps and debris NEVER operate the machine if all guardrails are not properly in place and secured with all fasteners properly torqued SECURE and lock gate after mounting platform NEVER use ladders or scaffolding on the platform NEVER attach overhanging loads or increase platform size LOOK up down and around for overhead obstructions and electrical conductors DISTRIBUTE all loads evenly on the platform See the back cover for maximum platform load NEVER use damaged equipment Contact UpRight for instructions See toll free phone number on back cover NEVER change operating or safety systems INSPECT the machine thoroughly for cracked welds loose hardware hydraulic leaks damaged control cable loose wire connections and wheel bolts NEVER climb down elevating assembly with the platform elevated NEVER perform service on machine while platform is elevated without blocking elevating assembly NEVER recharge batteries near sparks or open flame batteries that are being charged emit highly explosive hydrog
11. and that the Slide Out Deck Extension is secured with pin Attach Controller to left or right guardrail 4 Check clearances above below and to the sides of platform 5 Pull Controller Emergency Stop Button out to ON position In case of emergency push down to stop all functions 6 Position Function Switch to DRIVE For 20W 26 and 31 models position Function Switch to HI for traveling on level ground LOW when extra torque is required for climbing ramps 7 Grasp the Control Lever so the Interlock Lever is depressed releasing the Interlock Lever cuts power to Controller slowly push or pull the Control Lever to FORWARD or REVERSE position to travel in the desired direction The farther you push or pull the Control Lever from center the faster the machine will travel Steering 1 Position Function Switch to DRIVE 2 While holding the Control Lever so that the Interlock Lever is depressed push the Steering Switch to RIGHT or LEFT to turn wheels in the desired direction Observe the tires while maneuvering the work platform to ensure proper direction NOTE Steering is not self centering Wheels must be returned to straight ahead position by operating Steering Switch Elevating Platform 1 Position Function Switch to LIFT 2 While holding the Control Lever so that the Inter lock Lever is depressed push Control Lever forward to UP the farther you push the Control Lever the faster the Platform will elevate 3 If
12. ates add distilled water only 2 Connect extension cord 12 gauge 1 5 mm conductor minimum and 50 ft 15 m in length maximum to the charger outlet plug located at the rear of the machine Connect other end of extension cord to properly grounded outlet of proper voltage and frequency 3 Charger turns on automatically after a short delay the ammeter will indicate DC charging Current 4 Charger turns off automatically when batteries are fully charged Figure 8 Battery Module AF4HINDF4 1 000 699990 GayYINOAY I NLEX GAYINOAY F 000 999990 Anfu H313W dOLS EMO jq_siSSvHO uUNOH AS9N39H3IW3 LN dV SI a3yinmo348 1 NLE 900 2323 LOL N9Z SOO ZSZLOL MOZ 700 252101 NOZ 00 ZSZLOL Sal AvO1 133HM AFHINDIH 1 WNNIXYIN 000 225990 Ys9YVHO a3yINO34 1 AY3 1 1V9 S00 S0 190 35N4 ones dew wiayerd Buipuaasap wo aedu PIBZEH uD SIII02 4 c00 195990 uuoyeid Jamo7 s BeBu uid Bumnool ay nun evesq ajejoy saqn jonid 1 u o JOSSS OM ay SJeajo BdeIG ay Inun woed ay ajenaja o sjouoo sisseyo sn AO1d3q SOV 3ONVN31NIVIA 1930 30N31X4 NO s810652 NOSH3d I NVH1 38014 ON QHYZYH YJA0 dIL SERIALE Aig a3yINOI4 1 2351 380438 TWONWW S OLVH3dO LINSNOD NOLLNYS dave onas xwn r jasv oa av _ JON MS i JHDIGH WHOLLY XYW ON 1300W agyinoJy z Eooce Yo VWS 15 Md SLIL GALVINSNI ATIYORLLOTT3 LON SINYOALYIG SIHL 000 LScLOL la 8 6
13. e counterclockwise until it locks into position parallel with the scissor arm 3 Push Chassis Lift Switch to DOWN position and completely lower platform Routine Service Use the following table as a guide for routine maintenance refer to the Service Manual for complete service instructions SERVICE OPERATION Monthly 6 Months 2 Years Daily 0 or 50 Hrs 250 Hrs 1 x za w ES MESA Check hydraulic fluid level ES missing labels amp replace ES Inspect elevating assembly ES So 3 gt gt lt Check battery fluid level Charge batteries x gt gt lt O O O O gt gt o D O R O O O 5 A gt o y g z 5 Glo yo YN D D 9 gt O 5 gt S Q Q o N a 3 gel ab 0 D So as 2 3 Q gt lt x x damage O OIS oO 3 33 0823 O olg 209 gt 5 2A D ao Do gt O o BD a Ro Q Ox a O S os a gt O Q lt 9 2 6 a o p D 2 3 5 O Cc Co gt D gt lt valveoperation X a brushes propertorque O O O y D se D O 5 O O O N N 99 LO 9 233 2 ses 3 sol 81 3 3 al RE o 2 gt Q O O X Check allfasteners for propertorque Grease front spindle bearings Grease pot hole protection cylinder rod end bearing Q SI ab Q D lt o pa gt o Battery Maintenance A WARNING A Hazard of explosive gas mixture Ke
14. en gas AFTER USE secure the work platform against unauthorized use by turning key switch off and removing key NEVER replace any component or part with anything other than original UpRight replacement parts without the manufacturers consent SuO 9ni1suil bunelado pue sajny jajes UY cC O pur Q sf UY O cC pur 0 0 Q O cC Y Y O CC Dr PR 0 N Introduction This manual covers all models of the X Series Work Platforms This manual must be stored on the machine at all times Pre Operation and Safety Inspection Read understand and follow all safety rules and operating instructions and then perform the following steps each day before use 1 Open modules and inspect for damage oil leaks or missing parts 2 Check the level of the hydraulic oil with the platform fully lowered Open the Left Module and remove the reservoir cap oil should be visible in the filler screen Add ISO 46 hydrau lic oil if necessary 3 Check that fluid level in the batteries is correct See Battery Maintenance Page 8 4 Verify batteries are charged 5 Check that A C extension cord has been disconnected from charger 6 Check that all guardrails are in place the Slide out Deck Extension is secured with the pin and all fasteners are properly tightened 7 Carefully inspect the entire work platform for damage such as cracked welds or structural members loose or missing parts
15. ep sparks flame and smoking materials away from batteries Always wear safety glasses when working with batteries Battery fluid is highly corrosive Rinse away any spilled fluid thoroughly with clean water Always replace batteries with UpRight batteries or manufacturer approved re placements weighing 62 lbs each Check battery fluid level daily Figure 7 especially if work platform is being used in a warm dry climate If electrolyte level is lower than 3 8 in above plates add distilled water only DO NOT use tap water with high mineral content it will shorten battery life Keep terminals and tops of batteries clean Refer to the Service Manual to extend battery life and for complete service instructions v Battery Charger u Charger Plug Behind Guard Figure 7 Battery Charger Battery Charging Charge batteries at end of each work shift or sooner if batteries have been discharged A WARNING A Charge batteries in a well ventilated area Do not charge batteries when the work platform is in an area containing sparks or flames Permanent damage to batteries will result if batteries are not immediately recharged after discharging Never leave charger operating unattended for more than two days Never disconnect cables from batteries when charger is operating Keep charger dry 1 Check battery fluid level Figure 7 If electro lyte level is lower than 3 8 in 10 mm above pl
16. h 28 12 kg 4 HP pC Electric Motor DC Electric Motor DC Electric Motor DC Electric Motor System Voltage 24 Volt DC 24 Volt DC 24 Volt DC 24 Volt DC Battery Charger 25 AMP 60 Hz 110 VAC 25 AMP 60 Hz 110 VAC 25 AMP 60 Hz 110 VAC 25 AMP 60 Hz 110 VAC Battery Duty Cycle 25 for 8 Hours 25 for 8 Hours 25 for 8 Hours 25 for 8 Hours Hydraulic Tank Capacity 4 Gallons 15 2 4 Gallons 15 2 4 Gallons 15 2 5 Gallons 19 Maximum Hydraulic System Pressure 2400 psi 165 Bar 2600 psi 179 Bar 2600 psi 179 Bar 2000 psi 138 Bar Lift System Three stage scissor assembly Three stage scissor assembly Four stage scissor assembly Five stage scissor assembly actuated by one Single Stage actuated by one Single Stage actuated by one Single Stage actuated by two Single Stage Lift Cylinder Lift Cylinder Lift Cylinder Lift Cylinders Control System Smooth one hand joystick with Smooth one hand joystick with Smooth one hand joystick with Smooth one hand joystick with two speed operation two speed operation two speed operation two speed operation Drive System Dual Front Wheel Hydraulic Motors Dual Front Wheel Hydraulic Motors Dual Front Wheel Hydraulic Motors Dual Front Wheel Hydraulic Motors with series operation with series or parallel operation with series or parallel operation with series or parallel operation Tires 15 in 381 mm Diameter Solid 15 in 381 mm Diameter Solid 15 in 381 mm Diameter Solid 15 in
17. ng the following checks from the ground A WARNING A STAND CLEAR of the work platform while performing the following checks Protect control console cable from possible damage while performing checks 20 Pull Emergency Stop Button out to the ON position 21 Position Function Switch to DRIVE For 20W 26 and 31 models use both HI and LOW drive when performing step 22 22 Grasp the Control Lever so the Interlock Lever is depressed releasing the Interlock Lever cuts power to Controller slowly position the Control Lever to FORWARD then REVERSE to check for speed and directional control The farther you push or pull the Control Lever from center the faster the machine will travel 23 Push Steering Switch RIGHT then LEFT to check for steering function 24 Push in the Emergency Stop Switch Button 25 Rehook Controller on side guardrail Figure 2 Controller Before operating work platform ensure that pre operation and safety inspection has been completed and any discrepancies have been corrected Travel With Platform Lowered 1 Check that route is clear of people obstruc tions holes and drop offs is level and is capable of supporting wheel loads 2 Verify Chassis Key Switch is turned to DECK and Chassis Emergency Stop Switch is ON pull button out 3 After mounting platform lower top rail across en trance and secure entryway closure Check that guardrails are properly assembled in position
18. terlock Lever is depressed pull back on the Control Lever A warning alarm will sound when lowering Emergency Lowering Fold Down Guardrails This procedure applies only to the X31N model for A WARNING A the purpose of passing through a standard double If the platform should fail to lower NEVER doorway Guardrails must be returned to proper climb down the elevating assembly position before operating the work platform Ask a person on the ground to open the Fold Down Procedure Emergency Lowering Valve located at the rear of the machine Figure 3 1 Unhook the controller from the side guardrail and place on the platform 1 Open the Emergency Lowering Valve by 2 Unpin the front and rear upper rails from the pulling on the handle side rails and rotate inwards 2 To close release the handle 3 Starting with the rollout deck rails and then the outer rails lift up on each guardrail and fold inward Erection Procedure 1 Starting with the outer rails and then the rollout deck rails raise each guardrail and drop it down securing it in the vertical position 2 Rotate the front and rear upper rails outward and secure them to the opposite side rails using the retaining pins 3 Hang the controller on the side guardrail Dr Mn a lt Go w k 2 GS jp X20N X20W and Jaw X26N Models Figure 3 Emergency Lowering Valve Handle Parking Brake Release Figure 4 Perform the following only when the machine
19. the machine is not level an Alarm will sound and the machine will not lift or drive If an Alarm sounds immediately lower the Platform and move the machine to a level location before attempting to re elevate the Platform Depression Mechanism System When the platform is elevated the depression mecha nism system will automatically deploy The depression mechanism system will retract automatically when the platform is lowered and high speed drive is engaged Be aware that while the depression mechanism system is deployed minimum ground clearance is reduced to 4 inches Travel With Platform Elevated NOTE Work platform will travel at reduced speed when platform is elevated 1 Check that route is clear of persons obstruc tions holes and drop offs is level and capable of supporting the wheel loads 2 Check clearances above below and to the sides of platform 3 Position Function Switch to DRIVE position 4 Grasp the Control Lever so the Interlock Lever is depressed releasing the Interlock Lever cuts power to Controller push Control Lever to FORWARD or REVERSE for desired direction of travel 5 Ifthe machine is not level an Alarm will sound and the machine will not lift or drive If an Alarm sounds immediately lower the Platform and move the machine to a level location before attempting to re elevate the Platform Lowering Platform 1 Position Function Switch to LIFT 2 Grasp the Control Lever so the In
Download Pdf Manuals
Related Search