W.MACHINE/WASHER-DRYER 31000831 SE234
Contents
1. Ge DRAIN PUMP OPTION SWITCH LED BOARD VALVE 2004 GIAS U K Hoover Ltd SE 160 E ASM 160 Wash M cs SAS ASM 160 SE 234 80 SE 264 80 CIRCUIT DIAGRAM 2004 GIAS U K Hoover Ltd 12 SE 160 E ASM 160 Wash Mics CTO ASM160 SE 234 80 SE 264 80 WIRING DIAGRAM 2 N WHITE 982 84281241 d Ya 2 108 MOTI3A 31992 SNIVIN WHITE RED WHITE 1 550 WHITE O 2004 GIAS U K Hoover Ltd Ne SE 160 E ASM 160 Wash Mics Salas Fitting Notes WORKTOP REMOVAL e The worktop is of a new design and features a removable rear support allowing access to the machine by sliding the hardboard top off e The rear support is removed by undoing the three 7mm screws this will then allow the worktop surface to be removed by sliding it to the rear e The side supports can then be removed by sliding to the rear BEZEL REMOVAL To remove the bezel firstly remove the worktop side supports allowing access to the two screws holding the bezel in position Remove the two screws e The bezel will then need to be eased up and pulled out of its seating TIMER AND CONTROL KNOB REMOVAL e Once the bezel is removed pull off the control knob and this will then reveal the timer actuating cam remove the 8 mm nut remove the cam assy Access can then be gained to the 2 x Phillips head screws securing timer to inner bezel support Remove the two screws and take the timer off the beze2. 12 attempts if still very unbalanced then the cam position will cause the drum to remain stationary for the remainder of spin time The machine also monitors the load at 650 rpm if still slightly unbalanced at this point it will try three times to even the loadiif it fails the machine will carry on spinning at 650 rpm until the end of the program If the drum is not out of balance the module allows the machine to spin as shown in the graph below Ideal Spin Sequence T5 ELECTRICAL TESTING Earth Continuity Earth pin on plug top to 1 Door Hinge Max 10 2 Drum Inner Max 10 Insulation CCP Bonded to Earth spin selected door shut Switched On Minimum 2 O 2004 GIAS U K Hoover Ltd PAGE 3 LIMESCALE REMOVER DEGREASE PURIFIER amp HYGIENIC CLEANER FOR WASHING MACHINE amp DISHWASHER ANTICALCARE DISINCROSTANTE IGIENIZZANTE PER LAVATRICI E LAVASTOVIGLIE DISINCRUSTANTE DE CAL Y LIMPIADOR HIGIENICO PARA LAVADORAS Cod 49022949 Y LAVAVAJILLAS
3. 91601842 Module protection cover 91601843 Support bracket 92884204 Siphon 41000762 Shock absorb conn bracket 92898790 Therm press push b supp 03870756 Unipolar NA P A switch 90489683 Control support plate 91802090 Door handle assembly 91601653 Timer protection 03420083 Copyright 2011 Gias S r L Assistenza Tecnica After Sales Service Service Apres Vente Kundendienst Servicio Post Venta 31000831 SE234 80 0442 12 10 2004 Ricambio Inizio Part No Beginning Debut amp Pieza Inicio Hinge plaque 92897347 Door upper hinge 41005451 Door lower hinge 41005452 Tach coil 49000464 Thermostat hole stopper 92898394 Discharge pipe circlip 09077298 Upper counterweight support 92898915 Lower counterweight supp 92898923 Magnet 49000465 Clip 92470384 Drum paddle 03870539 Plug 92943216 Ring 97910459 Door release link 90384405 Tie rod 92401447 Instruction for use 40002147 Trade mark plate 41000597 Copyright 2011 Gias S r L SE 160 E ASM 160 Wash M cs 29145 ELECTRIC DIAGRAM KEY 134 ColdFill Valve 151 Timer Selector Motor 152F 1 Option Button 152F 2 Option Button 152F 3 Option Button 153 Low High Pressure Switch 155 On Off Pilot Lamp 161 Drain Pump 162 Door Micro switch 164 Mains Suppressor 286 Heater 287M N T C Thermostat 473 Motor 479 Control Module 618C On Off Switch 2004 GIAS U K Hoover Ltd SERVICE GIAS 328C SE160 E CIRCUIT DIA
4. Assistenza Tecnica After Sales Service Service Apres Vente Kundendienst Servicio Post Venta HOOVER 5 W MACHINE WASHER DRYER 31000831 SE234 80 Service Manual Z ZEROWNT Gaffe Kelvinator 2 NW Ofsein amp nosiEREs 3X iberna SE 160 E ASM 160 Wash M cs SAS SE160 E 2004 GIAS U K Hoover Ltd SE 160 E ASM 160 Wash M cs 29145 2004 GIAS Hoover Ltd 160 E ASM 160 Wash M cs Galas 190 di 155 155 494 ES 2004 GIAS U K Hoover Ltd SE 160 E ASM 160 Wash M cs 29145 2004 GIAS Hoover Ltd SE 160 E ASM 160 Wash M cs EISE 2004 GIAS U K Hoover Ltd Assistenza Tecnica After Sales Service Service Apres Vente Kundendienst Servicio Post Venta 31000831 SE234 80 0442 12 10 2004 Ricambio Inizio Part No Beginning Debut 213 Pieza Inicio Programs disc 03841518 Buffer with spring service pack 97917116 Cam disc 03850314 Button 03841445 Button protection 03841444 Control panel 40002149 Dispenser drawer front 04230676 R H side frame 03940686 L H side frame 03940687 Top rear frame 03940685 Work top 03410167 Hinge 91700102 Counter ring 91601645 Door surround 91601647 Door glass 91600903 Door catch 91601655 Spring 91408713 Glass door with frame 91670644 Screw 09031030 Cabinet assy 04230672 Rear panel 97911044 S
5. GRAM LED PCB Br Ze 151 ON OFF SWITCH 5 m 47 o BV ra DS 162 5 DOOR m UN LL 161 MISWITCH 4 zi 2 DRAIN PUMP To B EE EVC 134A e ae 2 ac HOT FILL 2 o VALVE NY DE m EVI O SE E 134 COLD FILL O 0 VALVE LS c 5 E zw uj PILOT LAMP Hi o 7 gt ok 2 eo 151 5 O TIMER o SELECT p MOTOR 5 w O F N 0 D 153 PRESSURE 7 7 6 SWITCH 0004 5 SE 160 E ASM 160 Wash M cs 2004 GIAS U K Hoover Ltd SERVICE o GIAS 5 SE 160 E ASM 160 Wash M cs SE160 E WIRING DIAGRAM YELLOW J MC NTC 191817151515151217 2 TN lue YELLOW ou NTC o 1 gt 811 7 6 473 pr DT2 B MOTOR 3 ST3 WHITE 151 ITCH i A 162 DOOR NJ M SWITC PILOT 3 LAMP Q 8 2 zi 5 I gt m a 7 nm z 2 52722172221 m E 3 53 5 2 2 gt gt ge pita s 164 SUPPPRESSOR CONTROL 1111111110 328 MODULE LED PCB a EV MP MR o 6 88 0 ST V T4 3 T2 1 9 H om SI D H 2 S03 E z D bo E MP DEN 134A HOT FILL 134 161 328B VALVE
6. e on its right hand side timer side taking care to ensure that the shell assy interior is protected with some hardboard Remove the four 7mm machined screws from the base of each suspension strut The tub assy is now free to be carefully removed from the shell Access to the lower tub weight is now available and is held in place by three 10mm bolts The drum can now be accessed by removing 16 screws from the tub front The tub front can be lifted away with the tub shell gasket attached To remove the drum Remove the drum pulley and the drum can be withdrawn from the front of the tub The drum may be very tight and require knocking out of the tub Care must be taken to protect the drum shaft threads with a packing bolt O 2004 GIAS U K Hoover Ltd PAGE 2 NE SE 160 E ASM 160 Wash Mics Salas TUBS MUST BE CHANGED COMPLETE The drum bearings are not serviceable Make sure when fitting the suspension dampers that they are fitted with the plastic rod end on to the base of the cabinet positioned so that the smooth face of the alloy housing faces inward towards the tub NOTE ON OUT OF BALANCE DETECTION The timers used on these machines have Out Of Balance detection on the module and operate in the following way At the start of the spin sequence as the machine ramps to 95rpm the load on the motor is monitored as follows If the machine is heavily unbalanced the spin sequence restarts and the process can continue for up to
7. ginning Debut amp Pieza Inicio Motor connector 27719213 Drum 04240181 Tub 97923565 Front flange 04240184 Drum shaft assy 04150062 Bolt 97923474 Tub gasket 92131689 Seal retainer 92445600 Bolt 21446068 Nut 92424209 Gasket 92445626 Tub gasket clip 91750458 Tub gasket clip 90488603 Heater holder 97910301 Support spring 92484492 R H support spring 92484484 Washer 92430206 Counter weight washer 40001133 Bolt 92419472 Bolt 97911507 Slide 09078825 Clamp 97910061 Upper balance weight 97910491 Lower balance weight 03940700 Telescopic shock absorber 92484518 Washer 97910509 Nut 97915565 Support 92673961 Door gasket 41008852 Discharge pipe 41001597 Fill pipe 91620033 Copyright 2011 Gias S r L Assistenza Tecnica After Sales Service Service Apres Vente Kundendienst Servicio Post Venta 31000831 SE234 80 0442 12 10 2004 Ricambio Inizio Part No Beginning Debut amp Pieza Inicio Pressure switch air chamber 06012804 5x8 hose 66655731 Steam hose 03860457 Hose spring 90386137 Hose clip d44 92470137 Heater 91201546 NTC probe 92743616 Drum pulley 92723824 Drive belt 92130442 Clips 92473636 Screw x hinge 97917587 Commutator motor 41002725 Coreboard 32K programmed 09200350 Electronic control 32K not programmed 41003803 Brush with brush holder 49000466 Special bolt 09183567 Mains cable x UK 91200201 Red window 91611509 Hose clip 06012880 Sleeve 91601654 Knob handle 03841449 Module protection
8. l OPTION SWITCH REMOVAL e The option switch support assy can be removed by undoing the 5 screws attaching it to the bezel e Remove the buttons from the switch being replaced e The switch can then be pushed through the support PRESSURE SWITCH REMOVAL e The pressure switch is secured by a bracket attached to the inner metal support underneath the timer and can be removed by a single screw attached to the bracket SOAP DISPENSER REMOVAL SETUP The soap dispenser is serviceable and contains three compartments the third compartment being available to incorporate the use of fabric conditioner To remove the dispenser remove the worktop and bezel disconnect all hoses disconnect dispenser actuating arm from the top of the dispenser noting the setting of the arrow on top of dispenser remove the single phillips head screw from the top front of bezel the dispenser can then be removed complete TO SETUP DISPENSER ACTUATING ARM Program 1 pointer at 1 notch Program 2 pointer at 2 notch Program 5 Pointer at 3 notch Program 6 pointer at 4 notch O 2004 GIAS U K Hoover Ltd PAGE 1 12 SE 160 E ASM 160 Wash Mes Galas DOOR GASKET REMOVAL To remove the gasket assy firstly remove the plastic clamp band around the front of the gasket To remove the inner clamp band a 7mm nut spinner and 7mm open ended spanner will be required Re fit gasket in reverse order taking care to ensure that the cut out on the side of the ga
9. ocle 41006148 Rear foot 92606474 Front foot 92692300 Filter knob with gasket 06015493 Filt hous w filter cartridge 91941772 Hose 41010982 Dispenser drawer 03870775 Rack 41005935 Dispenser bottom section assy 03870708 Dispenser top section 03870774 Copyright 2011 Gias S r L Assistenza Tecnica After Sales Service Service Apres Vente Kundendienst Servicio Post Venta 31000831 SE234 80 0442 12 10 2004 Ricambio Inizio Part No Beginning Debut 5 Pieza Inicio Water injector nozzle 92149327 Distribution connecting rod 92884212 Lever 97910582 Driving lever 41000950 Hose clip 92470061 Cam 06012915 Spring 92483148 Hose clip 92470020 Hose clip 92470194 Hose 97910517 Hose clip 92470012 Solenoid valve 25686057 Drain hose 92693373 Drain house elbow 92689587 Hose clamp 92895051 Fill hose 92250869 Motorized selector 30 settings 91201337 Switch assy Unipolar 91201694 Pressure switch 28375052 Indicator light 91209510 Wiring harness 04660497 7 Way connection 97911473 6 Way connecton 97911481 11 Way connecton 97911499 Water valve harness 91201486 Timer harness 91201360 Motor to module harness 91201485 Mains block 91623678 Drain recycle pump complete 97922819 Door safety device 91201208 Anti jamming filter radio 91212795 Copyright 2011 Gias S r L Assistenza Tecnica After Sales Service Service Apres Vente Kundendienst Servicio Post Venta 31000831 SE234 80 0442 12 10 2004 Ricambio Inizio Part No Be
10. sket lines up with the hose assy where used situated at approx 9 o clock DOOR INTERLOCK REMOVAL A Bl metal type interlock is fitted on all models To gain access to the interlock remove the clamp band surrounding the tub shell gasket and ease the front of the gasket off the shell Remove the two screws holding the interlock and it can be removed from the door aperture Note the wiring connections before removing the original interlock e After servicing the door interlock make sure that the clamp band is replaced MOTOR ASSY REMOVAL To remove the motor firstly remove the non adjustable elasticated belt the motor can then be removed by undoing the two 10m m self tapping bolts Care must be taken when removing and refitting the motor To prevent damage to the motor supports place a block of wood at the rear of the motor under the tacho assembly and tap the motor to gently ease it away from the mountings DRUM AND TUB REMOVAL Remove the Worktop Open the door and undo the two screws holding the door amp the hinge lift away the door assembly including the hinge Remove the gasket clamp band release the gasket from the shell and push it through into the cabinet Remove the top weight assy two 10mm and one 13mm securing bolts from tub assy Remove timer assy and associated wiring motor assy thermostat heater connections earth connection for drum bearing sump hose and pecker assy Carefully lay the machin
Download Pdf Manuals
Related Search