Boom! Audio Ipod Interface Module Kit Instruction - Harley
Contents
1. H HI ae ler 274A 275B an a 9 Ho 6B Www Figure 4 Service Parts iPod Interface Module Table 1 Service Parts Item Description Quantity Part Number 1 Module iPod Interface 72647 11 2 Harness iPod Navigation Interface Module NIM 76477 10 3 Pin housing six way Deutsch DTM black 74106 98BK 4 Seal pin 6 74195 98 5 Cable iPod 72651 11 6 Cable strap 4 10006 J05168 4 of 42. near the front of the seat NOTE e Take care to route the cable so it will not be pinched by the seat or anything else on the vehicle Do not fasten the iPod cable too tightly with cable straps as it is easily damaged 11 Use cable straps 6 from the kit to fasten the iPod NIM harness and the iPod cable to the vehicle harnesses inside the fairing RETURN TO SERVICE NOTE To prevent possible damage to the sound system verify that the ignition key switch is in the OFF position before installing the main fuse 1 See the service manual and install the main fuse 2 Plug the iPod cable connector into the iPod 3 Turn the ignition key switch ON and test the iPod for proper operation Playlists artists and song titles may be selected from the radio display using the hand controls or radio soft keys 4 Install the outer fairing and windshield per service manual instructions IN USE WARNING Set volume levels and other controls on audio and elec tronic devices before riding Distractions can lead to loss of control resulting in death or serious injury 00088b See the Boom Audio iPod Interface Module owner s manual for operating instructions 3of4 OMDNOORWN OANOUAWN 6B 64 isO6560 6B 6A Figure 3 Wiring Diagram iPod Navigation Interface Module SERVICE PARTS isO6557
3. MOTOR HARLEY DAVIDSON WY J05168 INSTRUCTIONS REV 2011 09 22 BOOM AUDIO IPOD INTERFACE MODULE KIT GENERAL Kit Number 76476 10 Models For model fitment information see the P amp A retail catalog or the Parts and Accessories section of www harley davidson com English only Refer to the Boom Audio iPod Interface Module owner s manual for compatible iPod devices Installation Requirements FLHT models will require prior installation of an Advanced Audio AM FM CD Radio Kit Part No 76412 06 and an AM FM Antenna Kit Part No 76325 06 or 7631 7 06 FLHT C FLHX FLTR X and FLHXXX models WITHOUT Non Ultra Overlay Harness Part No 70169 06 installed will require separate purchase of a Connector Kit Part No 69200033 If two modules are already installed on top of the radio For FLHT C U FLHX and FLHTCUTG models two Dual Lock mounts Part No 76434 06 may be used to mount the iPod Interface Module across the tops of the two modules For FLTR and FLTRX models the iPod Interface Module can be mounted on the inner fairing right side glove box inboard wall using either of these methods see Figure 2 e Use two Dual Lock mounts Part No 76434 06 to attach the module directly to the side of the glove box Use an acorn nut Part No 90844 80 to attach the module to an iPod mounting bracket Part No 83276 11 Fasten two Dual Lock mounts Part No 76434 06 to the underside of the mountin
4. g bracket Mount the bracket and module to the front of the glove box with a screw Part No 3658 and washer Part No 6716 For ALL models To install the iPod inside the right side saddlebag a BOOM Audio Saddlebag iPod Mount Kit Part No 76000143 can be used J05168 Many Harley Davidson Parts amp Accessories are made of plastics and metals which can be recycled All these items are available separately from a Harley Davidson dealer WARNING The rider s safety depends upon the correct installation of this kit Use the appropriate service manual procedures If the procedure is not within your capabilities or you do not have the correct tools have a Harley Davidson dealer perform the installation Improper installation of this kit could result in death or serious injury 00333a NOTE This instruction sheet refers to service manual information A service manual for this year model motorcycle is required for this installation and is available from a Harley Davidson dealer Electrical Overload NOTICE It is possible to overload your vehicle s charging system by adding too many electrical accessories If the combined electrical accessories operating at any one time consume more electrical current than the vehicle s charging system can produce the electrical consumption can discharge the battery and cause damage to the vehicle s electrical system See an authorized Harley Davidson dealer for advice about the amou
5. module fitting firmly into the leftmost rubber grommets 3 at the front of the radio c Fasten the module to the radio with the radio case screw 2 Tighten to 35 45 in Ibs 4 0 5 1 Nm 2 See the wiring diagrams in the service manual appendix Locate the black six way vehicle interconnect harness socket housing 6B near the back of the radio If socket housing 6B is connected to pin housing 6A on the vehicle audio harness separate the two connector halves is06559 1 iPod module 2 Radio case screw 3 Grommet 2 Figure 1 iPod Module Installation J05168 Right side glove box iPod Module Dual Lock mount 2 sets Part No 76434 06 iPod mounting bracket Part No 83276 11 Screw Part No 3658 Washer Part No 6716 Acorn nut Part No 90844 80 1 2 3 4 5 6 7 Figure 2 Alternate iPod Module Mounting Configurations for FLTR and FLTRX Models 3 Models WITHOUT 35 Way connector on back of radio Get the Connector Kit Part No 69200033 sold separ ately and install the wire terminals and seal plugs per the instructions in that kit Models WITH 35 Way connector on back of radio See Figure 3 and Figure 4 Unplug the 35 way connector 28B from the back of the radio Follow instructions in the ser vice manual appendix to remove the seal pins from cavities 8 19 and 31 Insert three of the terminated wires from the iPod NIM harness into connector 28B as follo
6. nt of current consumed by addi tional electrical accessories or for necessary wiring changes 0021 1c WARNING When installing any electrical accessory be certain not to exceed the maximum amperage rating of the fuse or circuit breaker protecting the affected circuit being modi fied Exceeding the maximum amperage can lead to elec trical failures which could result in death or serious injury 00310a The iPod Interface Module requires up to 400 milliamps additional current from the electrical system Kit Contents See Figure 4 and Table 1 Please dispose of materials responsibly PREPARATION NOTE For vehicles equipped with security siren 2007 and later Verify that the Hands Free Fob is present e 2006 Disarm the siren with the key fob e ALL vehicles Turn the ignition key switch to IGNITION WARNING To prevent accidental vehicle start up which could cause death or serious injury remove main fuse before pro ceeding 00251b 1 See the service manual and remove the main fuse 2 Remove the outer fairing and windshield per the service manual STANDARD INSTALLATION NOTE For optional installation methods refer to Installation Requirements earlier in these instructions 1 See Figure 1 Locate the iPod module 1 on top of the AM FM radio case a Remove the screw 2 at the back of the radio b Position the iPod module on top of the AM FM radio with the metal cones on one end of the
7. ted and locked into the 35 way socket housing 28B before plugging back into the radio 6 Plug connector 28B into the back of the radio 7 Ifa NIM is also installed see the instructions in that kit for detailed mounting and electrical connections If a NIM is not installed insert the cavity seal plugs 4 into the loose six way housing 3 from the kit Install the six way housing on the unused pin housing 275B of the iPod NIM harness NOTE If the iPod is being installed in the right side saddlebag using a BOOM Audio Saddlebag iPod Mount Kit Part No 76000143 available separately see the instructions in that kit The longer cable from that kit will be connected to the round connector on the iPod module in the next step 8 Connect the iPod cable 5 to the round connector on the iPod module Align the arrows and push The connector will lock to the cable port with an audible click 9 Route the iPod cable under the radio and though the inner fairing near the steering head NOTE DO NOT mount iPod models with a hard drive memory on the vehicle Vehicle vibration can permanently damage the device Refer to the iPod instructions to determine if the model to be used has a hard drive memory 10 Some iPod models may be mounted on the tank using the Boom Audio Tank Pouch available separately J05168 The cable may also be routed under the tank inside the wire caddy alongside other harnesses and up to the rider
8. ws e Insert the tan red wire terminal into cavity 8 e Insert the violet gray wire terminal into cavity 19 e Insert the tan blue wire terminal into cavity 31 If an Advanced Audio Bluetooth Hands Free Cell Phone Interface Part No 76408 06 IS ALSO installed individually wrap the ends of the remaining two red blue and black blue terminated wires from the iPod NIM harness with electrical tape to prevent electrical problems If an Advanced Audio Bluetooth Hands Free Cell Phone Interface IS NOT installed insert the remaining two terminated wires from the iPod NIM harness into connector 28B as fol lows Remove the seal pins from cavities 4 and 27 e Insert the red blue wire terminal into cavity 4 e Insert the black blue wire terminal into cavity 27 4 For ALL installations Mate the six way pin housing 6A of the iPod NIM harness to socket housing 6B on the vehicle interconnect harness If vehicle interconnect harness 6B was unplugged from audio harness 6A in step 2 mate the six way socket 2 of 4 housing 6B of the iPod NIM harness to pin housing 6A on the audio harness If vehicle interconnect harness 6B was NOT con nected in step 2 the six way socket housing 6B of the iPod NIM harness can be left unconnected 5 Plug the eight way connector 274B of the iPod NIM har ness into the iPod interface module 1 connector 274A NOTE Be sure to check that all socket terminals are fully sea
Download Pdf Manuals
Related Search