Home

Vision™ 2.0 Retrofit User Manual

Contents

1. Start 101 0 69 A My Stitch Buttons Start Stop Stitching Adjust Setting Up To engage the Horizontal Channel Lock Tap the open Horizontal Channel Lock icon Notice the icon locks indicating the channel lock is engaged and the machine only moves in a horizontal direction left or right but cannot move up or down vertically To disengage the Horizontal Channel Lock Tapthe closed Horizontal Channel Lock icon e Notice the icon unlocks indicating the channel lock is disengaged and the machine moves freely in all directions PN140 0007 Rev00 Vision M 2 0 User Manual 58 VERTICAL CHANNEL LOCK The Vertical Channel Lock Icon limits the motion of the machine to a vertical direction not allowing any horizontal movement This feature aids in creating perfectly straight lines whether for basting or stitching F ydd E Gammill Vision 2 Q v 20 Connected to GAMMILL VISION2 E18E c My Stitch Presets eee eo REGULATE REGULATE CONSTANT 16 SPI Speed 25 Stitches per Inch Regulate 12 97 0 69 101 My Stitch Buttons Adjust Setting Up Start Stop Stitching To engage the Vertical Channel Lock Tapthe open Vertical Channel Lock icon Notice the icon locks indicating the channel lock is engages and the machine only moves in a vertical direction up or down but cannot move left or right horizon
2. Locks the head to only move in the Horizontal Lock horizontal direction Locks the head to only move in the Vertical Lock vertical direction Laser Turns the laser on or off Accesses the menu options for Menu Tab specialized functions e T Allows the constant stitching mode Constant to be selected CONSTANT PN140 0007 Rev00 Vision M 2 0 User Manual 27 Allows the regulate stitching mode to be selected REGULATE gt nep TTT Coast Regulate COAST REGULATE Allows the coast regulate stitching mode to be selected Allows the basting mode to be Baste ected WSS selecte BASTE KE My Stitch Presets Allows two modes and settings to be My Stitch saved for easy access and for use by CONSTANT REGULATE Presets 1 amp 2 the My Stitch buttons Speed 40 12 a Mode Section What you can do with it STITCHING MODE Ba ste Stitching Mode Indicates the active stitching mode Stitch Length 2 1 2 PS Stitch Setting Indicates the stitch setting and allows stitch adjustment Tracks stitching time and is Stitch Timer resettable PN140 0007 Rev00 Vision M 2 0 User Manual 29 Tracks the stitch count and is Stitch Counter resettable Initiates a series of tiny locking Tie Off Function stitches Start Button Starts stitching Stop Button Stops stitching Bottom Ribbon What you can do wi
3. PN140 0007 Rev00 Vision M 2 0 User Manual 35 BASTE MODE Baste mode functions like stitch regulation on a large scale stitching from inch up to 4 inches per stitch This helps to stabilize the guilt ram Gammill Vision 2 0 wd 20 Connected to GAMMILL VISION2 E18E My Stitch Presets 3 30 PM REGULATE CONSTANT 16 SPI Speed 25 Stitch Length Baste 21 2 Start O 484 8810095 FAN My Stitch Buttons Adjust Setting Up Start Stop Stitching To engage Baste Mode e Touch the Baste icon in the top ribbon e Notice stitching mode is indicated in the mode section in the middle of the screen To set Baste Mode e Touch the plus or minus sign to adjust the stitch length e Basting length can be set from 14 inch to inches in 14 inch increments To adjust Baste Mode while basting e Touch the plus or minus sign to increase or decrease stitch length while stitching BECAUSE THE MACHINE IS MAINTAINING A SET NUMBER OF STITCHES PER INCH WHEN THE HEAD STOPS MOVING STITCHING PAUSES MOVING THE HEAD WILL CAUSE IT TO RESUME STITCHING IF THE HEAD IS NOT MOVED FOR ao SECONDS THE MACHINE WILL STOP STITCHING PRESS THE START BUTTON TO RESUME STITCHING PN140 0007 Rev00 Vision M 2 0 User Manual 36 Over Speed Alarm The head was moved faster than regulation could maintain Long stitches may result PN140 0007 Rev00 Vision M 2 0 User Manual 37
4. ms yM mmf d 0 CIL 2 One 1 Vision 2 Retrofit Module TOOLS REOUIRED a J E 0 te d a a E Lia F EI T i 1 1 5 Tn mr IL y 1 4 T Handle Hex Wrench 3 32 Hex Wrench Included in Kit Included in Kit 5 64 Hex Wrench Adjustable Wrench Included in Kit PN140 0007 Rev00 Vision M 2 0 User Manual 10 PREPARATION 1 Turn both machine power switches to the OFF O position 2 Unplug the power cord from the rear of the machine 3 Removethe Vision main module from the dock Store the module away as it will no longer be necessary to operate the machine 4 _ Using an adjustable or 7 16 wrench loosen the jam nut and remove the stylus post from the top of the head Set the stylus post aside for use in the Side Plate Installation Section Optional y A A PN140 0007 Rev00 Vision M 2 0 User Manual 11 RETROFIT MODULE INSTALLATION 1 Record the information printed on the sticker on the bottom of the retrofit module This information may be reguired in a later section 2 Place the retrofit module onto a machine dock It is recommended that the front dock be used for easy viewing of the indicator lights but the rear dock may be utilized if the user prefers _ Hammill 3 While holding the
5. MY STITCH PRESETS My Stitch Presets offers a way to create presets for modes and settings This is very useful for commonly used values Additionally by using the My Stitch Select Button the user may change between the two presets without stopping stitching 3 32 PM Gammill Vision 2 0 v 20 Connected to GAMMILL VISION2 E18E My Stitch Presets ee CONSTANT CONSTANT REGULATE Speed 40 12 SPI Speed Constant 90 Start 0 69 496 Mv Stitch Buttons MyStitch Select R Start Stop Stitching To access a My Stitch Preset Tap the numbered My Stitch Preset button desired to access e Notice the stitching mode is indicated in the mode section in the middle of the screen and the active My Stitch Preset button is white To set a My Stitch Preset e Once mode and settings are adjusted touch and hold the desired preset button for 2 seconds to program it e Notice the mode and setting are indicated below the My Stitch Preset button To use the My Stitch Presets with My Stitch Buttons e Set one of the My Stitch Buttons to My Stitch Select e While stitching press the handle button set to My Stitch Select e Notice the stitching mode instantly changes to the newly selected preset while stitching PN140 0007 Rev00 Vision M 2 0 User Manual 38 EACH OF THE TWO PRESETS CAN BE SET TO ANY MODE AND SETTI
6. adjusted from 1 to 10 e Set the Thread Factor higher for thinner threads e Setthe Thread Factor lower for thicker threads Tap the OK button Bobbin Gauge Thread Factor amp Use the Bobbin Gauge 1 GE Reset the Gauge THE THREAD FACTOR IS A VALUE HELPS DETERMINE THE BOBBIN THREAD USAGE THE BEST WAY TO THINK OF THE FACTOR IS TO RELATE IT TO THE THICKNESS OF THE BOBBIN THREAD THE THICKER THE BOBBIN THREAD THE LESS THREAD WILL FIT ON A BOBBIN USE A LOWER NUMBER WHEN USING THICKER THREAD ADJUST THE BOBBIN FACTOR AND OBSERVE WHEN THE ALARM OCCURS VERSUS THE ACTUAL AMOUNT OF THREAD LEFT ON YOUR BOBBINS MAKE ADJUSTMENTS BASED ON THIS FEEDBACK UNTIL YOU OBTAIN THE DESIRED RESULTS To reset the Bobbin Gauge Tap Reset the Gauge button e Notice the Bobbin Gauge on the main screen is reset to 100 PN140 0007 Rev00 Vision M 2 0 User Manual 53 To disable the Bobbin Gauge Tapthe checked box beside the Use the Bobbin Gauge message e Notice the check mark disappears indicating the Bobbin Gauge is now inactive e Touch the OK button Thread Factor 10 00 Reset the Gauge e Notice the window closes and the Bobbin Gauge icon is greyed out on the main screen and no percentage is shown As you stitch the bobbin gauge percentage will decrease When the percentage reaches 1096 the system will issue an alert to warn you that the bobbin is almost empty PN140 0007 Rev00 Vision M 2
7. i Select items above then press Scan to run an automatic check of the machine s electronic communications PN140 0007 Rev00 Vision M 2 0 User Manual 96 e Touch the Reset button to retest the communication system Service amp Maintenance 40 Connected to GAMMILL VISION2 DDBD COMMUNICATIONS Messages Sent Z Drive Messages Received Messages Sent Messages Received Encoder Board Select items above then press Scan to run an automatic check of the machine s electronic communications To exit and return to the main screen press the left arrow at the top left of the screen Service amp Maintenance AJ20 Connected to GAMMILL VISION2 DDBD COMMUNICATIONS Messages Sent Z Drive Messages Received Messages Sent Messages Received 0 Select items above then press Scan to run an automatic check of the machine s electronic communications PN140 0007 Rev00 Vision M 2 0 User Manual 97 OILING Run the Oiling Routine to exercise the machine once it has been oiled after sitting for an extended period of time This routine helps get the oil properly distributed throughout the system Remove the thread and bobbin from the machine before using this screen 6 Failure to do this could cause damage to the machine EX JE Service amp Maintenance 20 Connected to GAMMILL VISION2 DDBD Ww OILING Time Remai
8. 7 H1 07 PM 68 The app will be automatically updated and prompt you when complete Gammill Vision 2 Installing To open the updated app Tapthe Open button Y Gammill Vision 2 Application installed PN140 0007 Rev00 Vision M 2 0 User Manual 69 If no update is found a message will pop up to let you know 417 PM No new version available If a new machine firmware update is included within the new application the application will prompt you with the steps to update the firmware To Update Firmware e Press OK to begin the update PN140 0007 Rev00 Vision M 2 0 User Manual 70 2 5 15PM Update Bluetooth module firmware 5 5 16PM Updating firmware 25690 66802 PN140 0007 Rev00 Vision M 2 0 User Manual ALERTS All alerts can be adjusted or disabled according to your needs Gammill Vision 2 40 Connected to GAMMILL VISION2 DDBD Alert Volume Level e IE 6 Bobbin Empty Alert Over Speed Alert Thread Break Alert Vw po 5 Reset to Defaults Move the volume slider to adjust the volume of the audible alerts Press the icons to enable or disable the pop up message and audible alert for these three alerts Adjust the Thread Break Sensor to change the sensitivity of the Thread Break Alert To adjust the volume of alert sounds e Drag the bubble on the slider e Dragging the slider to th
9. Vision 2 0 Retrofit User Manual Gammill Inc March 2014 Gammill Inc User Manual Vision 2 0 Retrofit IMPORTANT MACHINE INFORMATION It is our goal to ensure that Customers have information on the tools and accessories standard and optional that are available for use with Gammill quilting machines Some of the tools and accessories detailed in this Manual may be optional equipment We recommend that you consult with your Authorized Gammill Dealer or Sales Representative for the most current list of standard and optional equipment Standard equipment optional equipment and pricing are subject to change without notice Copyright 2014 Gammill Inc All Rights Reserved PN140 0007 Revoo March 2014 All rights reserved No parts of this work may be reproduced in any form or by any means graphic electronic or mechanical including photocopying recording taping or information storage and retrieval systems without the written permission of the publisher Products that are referred to in this document may be either trademarks and or registered trademarks of the respective owners The publisher and the author make no claim to these trademarks While every precaution has been taken in the preparation of this document the publisher and the author assume no responsibility for errors or omissions for damages resulting from the use of information contained in this document or from the use of programs and
10. plus button to increase the delay making the sensor less sensitive Gammill Vision 2 40 Connected to GAMMILL VISION2 DDBD Alert Volume Level Thread Break Bobbin Empty Alert Over Speed Alert Thread Break Alert Sensor Delay eG e 6 eo 8 8 Reset to Defaults Move the volume slider to adjust the volume of the audible alerts Press the icons to enable or disable the pop up message and audible alert for these three alerts Adjust the Thread Break Sensor to change the sensitivity of the Thread Break Alert PN140 0007 Rev00 Vision M 2 0 User Manual 73 TO GENERATE A THREAD BREAK ALARM THE SYSTEM LOOKS AT THE NUMBER OF STITCHES VERSUS THE MOVEMENT OF THE THREAD BREAK SENSOR IF YOU HAVE FALSE ALERTS WHEN MAKING LOTS OF SMALL FAST STITCHES OR WHEN USING VERY FINE THREAD INCREASING THIS VALUE SHOULD HELP ALLEVIATE THESE FALSE ALERTS Gammill Vision 2 40 Connected to GAMMILL VISION2 DDBD Alert Volume Level Bobbin Empty Alert Over Speed Alert Thread Break Alert elo o9o NN GA A y 5 I Reset to Defaults Move the volume slider to adjust the volume of the audible alerts Press the icons to enable or disable the pop up message and audible alert for these three alerts Adjust the Thread Break Sensor to change the sensitivity of the Thread Break Alert PRESS THE RESET TO DEFAULTS BUTTON TO RESET ALL SETTINGS ON THIS SC
11. RCH O ae dd E E Y Y eee 43 TE F UNC 48 LU O dy YY 52 Le S NE 56 Wsizelsmecsii 57 FFWR RH MM MINE MID HF MEMINI RUE 58 I gu ar C nanne oe de m m 59 60 Additional Features Future Enhancements oee ue Bd GA CD OA YO GO REMIS FEDR 62 MA TES Y A TV NE AN FN FY NN FFR EF CHYF ND NWFN 63 Settings and Other ais a SE NN I NN AN EN 65 YN NAF CYFA FFYNIANT FFA YF NAF CW AF YR EC FWYTA 65 UNFAN YC CN AT A NR CR CC ANF 66 8 6 NEFYN 72 PN140 0007 Rev00 Vision M 2 0 User Manual 3 5 Sc m EP 7 SR EF FFWR NR AF FRO FIR A 80 82 edau a GS HY UD NIE 84 Service amp Maintenance creens dd Yd ae EF FRO SC 85 Novda OM mec cc 85 97 WVOLO ODL Ola eni 90 0 95 I MILII I FFAW HATH 98 Needle POSION en dor N GO df eae lea 102 PN140 0007 Rev00 Vision M 2 0 User Manual 4 Welcome to the Vision 2 0 Retrofit by Gammill the latest in hand guided quilting technology at your fingertips Experience the
12. 0 User Manual 54 Bobbin is almost empty Please check bobbin and refill if necessary THE BOBBIN GAUGE MAY BE USED BUT ONLY THE ALERT DISABLED SEE THE SECTION ON THE ALERT SCREEN FOR ADDITIONAL INFORMATION ON THIS CAPABILITY PN140 0007 Rev00 Vision M 2 0 User Manual 55 CONNECTION INFORMATION The Vision 2 0 Application communicates to the quilting system using Bluetooth When connected the text will read Connected to Gammill Vision2 XXXX where XXXX is the last 4 digits of the address of the system it is connected to 7 2368 3 28 U r My Stitch Presets Gammi Connected to GAMMILL VISION2 E18E eee eo REGULATE REGULATE CONSTANT 16 SPI Speed 25 Stitches per Inch STITCHING MODE 1 2 Regulate 101 0 69 sic My Stitch Buttons Adjust Setting Up Start Stop Stitching IF THE APPLICATION IS NOT CONNECTED TO A SYSTEM IT WILL READ DISCONNECTED IF THIS IS THE CASE COMMUNICATION NEEDS TO BE ESTABLISHED SEE THE SECTION ON BLUETOOTH CONNECTION FOR ADDITIONAL INFORMATION ON HOW TO CONNECT THE TABLET TO THE SYSTEM PN140 0007 Rev00 Vision M 2 0 User Manual 56 NEEDLE STOP POSITION The top bar in the user interface contains several icons allowing guick and easy use of the machine The first of these icons controls the position of the needle when stitching stops 7 3 28 PM Gam
13. Regulate Mode controls the length of the stitch regardless of the movement of the machine Whether the head moves slowly or guickly the stitch length remains the same LJ d Ew PM Gammill Vision 2 0 wd 20 Connected to GAMMILL VISION2 E18E My Stitch Presets REGULATE REGULATE CONSTANT 16 SPI Speed 25 Stitches per Inch Regulate 12 Start O 101 0 69 9 My Stitch Buttons Adjust Setting Up Start Stop Stitching To engage Regulate Mode Tap Regulate icon in the top ribbon e Notice stitching mode is indicated in the mode section in the middle of the screen To set Regulate Mode e Adjust the stitch length up or down by tapping the plus or minus sign in the mode section e Stitch length can be set from 8 to 24 stitches per inch To adjust Regulate Mode while quilting Tap the plus minus sign to increase or decrease the stitch length while stitching BECAUSE THE MACHINE IS MAINTAINING A SET NUMBER OF STITCHES PER INCH WHEN THE HEAD STOPS MOVING STITCHING PAUSES MOVING THE HEAD WILL CAUSE IT TO RESUME STITCHING IF THE HEAD IS NOT MOVED FOR 10 SECONDS THE MACHINE WILL STOP STITCHING PRESS THE START BUTTON TO RESUME STITCHING PN140 0007 Rev00 Vision M 2 0 User Manual 32 Over Speed Alarm The head was moved faster than regulation could maintain Long stitches may result PN140 0007 Rev00 Vision M 2 0
14. Speed 40 12 SPI Stitches Number of per Inch Stitches Automatic Tie Off Reset to Defaults 4 Cancel 20 6 0048 3 496 6981005 976 My Stitch Buttons MyStitch Select R Start Stop Stitching PN140 0007 Rev00 Vision M 2 0 User Manual 44 To reset the defaults for the Automatic Tie Off e Touch the Reset to Defaults button located under the Automatic Tie Off label in the center of the screen e Notice Stitches per Inch and Number of Stitches settings return to their original settings amp d Gammill Vision 2 w 20 Connected to GAMMILL VISION2 E18E My Stitch Presets CONSTANT REGULATE Speed 40 12 SPI Stitches Number of per Inch Stitches p 1 00 48 496 258 100 6 TN My Stitch Buttons B MyStitch Select H Start Stop Stitching To cancel the Automatic Tie Off e Touch the Cancel button located under the Automatic Tie Off label in the center of the screen Ortouchthe tied bow icon again to cancel e Notice the screen changes back to the mode and settings selected prior to entering the Automatic Tie Off function Gammill Vision 2 J20 Connected to GAMMILL VISION2 E18E My Stitch Presets CONSTANT REGLILATE Speed 40 12 SPI Stitches Number of per Inch Stitches Automatic Reset to Defaults 20 0 5 00 48 6 69106 Fre My Stitch Buttons MySti
15. THE MACHINE WILL STOP STITCHING ON ITS OWN IF IT SENSES NO MOVEMENT FOR 10 SECONDS THIS IS A SAFETY FEATURE THAT CANNOT BE DISABLED PN140 0007 Rev00 Vision M 2 0 User Manual 30 STITCHING MODES Vision 2 0 features four stitching modes constant regulate coast regulate and baste Stitching modes are selected in the top ribbon and the active mode is displayed in the mode section and highlighted on the top ribbon CONSTANT MODE Constant Mode stitches at an unchanging speed The rate the needle moves up and down to stitch does not increase or decrease with the movement of the head but rather stays constant I F 3 28 Gammill Vision 2 0 0 20 Connected to GAMMILL VISION2 E18E My Stitch Presets CONSTANT REGULATE CONSTANT 16 SPI Speed 25 Speed Constant 25 Start 97 0 69 101 My Stitch Buttons Adjust Setting Up Start Stop Stitching To engage Constant Mode Tap the Constant icon in the top ribbon e Notice the stitching mode is indicated in the mode section in the middle of the screen To set Constant Mode speed e Adjust the speed up or down by tapping the plus or minus sign in the mode section e Speed can be set from o to 100 To adjust Constant Mode speed while quilting Tap the plus or minus sign to increase or decrease speed while stitching PN140 0007 Rev00 Vision M 2 0 User Manual 31 REGULATE MODE
16. TO IF YOU HAVE MULTIPLE MACHINES THAT YOU COULD CONNECT TO CONSULT THE ADDRESS PRINTED ON THE MACHINE DECAL AT THE REAR OF THE HEAD TO DETERMINE WHICH ADDRESS YOU WANT TO CONNECT TO PN140 0007 Rev00 Vision M 2 0 User Manual 92 5 Ew O 5 m Connected to GAMMILL VISION2 E18E 0 40 My Stitch Presets REGULATE REGULATE CONSTANT 16 SPI Speed 25 Stitches per Inch STITCHING MODE 1 2 Regulate 101 0 69 Start My Stitch Buttons Adjust Setting Up Start Stop Stitching PN140 0007 Rev00 Vision M 2 0 User Manual 83 OUICK START GUIDE Access the onboard Ouick Start Guide for basic instructions in threading oiling and interface navigation Lal F 265 4 02 PM vision2 quick start guide pdf 4 RA hu Vision 2 0 Quick Start Guide Gammill Inc March 2014 e The Quick Start Guide opens in a separate app e Swipe to scroll and pinch to zoom e Press the back arrow at the top left to return to the Vision 2 0 app PN140 0007 Rev00 Vision M 2 0 User Manual 84 SERVICE amp MAINTENANCE SCREENS NAVIGATION The Service amp Maintenance Screens is accessed through the main menu rem 4 02 PM Gammill Vision 2 20 Connected to GAMMILL VISION2 E18E Gammill Vision 2 About this App Alerts Needle Settings Laser Settings Display Settings Bluetooth S
17. Y encoders the machine handle buttons the needle position sensors and the thread movement sensor The associated indicator should turn green when you move the guilting arm move the needle to its up and down limits and press any handle button on the Vision 2 machine The thread movement count should increase as the thread break wheel is turned To check the Encoder Position Move machine to the left and right e Notice the green indicator on the encoder position moves left to right as you move the machine This verifies that the X encoder is working properly e Move the machine to the front and rear e Notice the green indicator on the encoder position moves up and down as you move the machine This verifies that the Y encoder is working properly 4 06 PM Service amp Maintenance Connected to GAMMILL VISION2 E18E BUTTONS amp SENSORS Encoder Position Handle Buttons Needle Position Thread Movement Use the indicators on this screen to check the performance of the X and Y encoders the machine handle buttons the needle position sensors and the thread movement sensor The associated indicator should turn green when you move the guilting arm move the needle to its up and down limits and press any handle button on the Vision 2 machine The thread movement count should increase as the thread break wheel is turned PN140 0007 Rev00 Vision M 2 0 User Manual 87 To check Handle Buttons e Press each handl
18. ease offered by My Stitch customizability Make your quilting system exactly the system you need PN140 0007 Rev00 Vision M 2 0 User Manual 5 PN140 0007 Rev00 Hisk for electric shock or burn Unplug machine before removing any machine covers Heavy weight Some components are heavy A minimum of two people should lift the head table parts or any other large components to prevent injury Moving needle and hopping foot can cause injury Keep body parts and loose clothing away Pinch points It is possible to pinch hands and fingers Be alert and keep hands clear Rotating parts can cause injury Keep hair body parts and loose clothing away Laser radiation Avoid direct exposure to beam Vision M 2 0 User Manual 6 VISION 2 0 RETROFIT FRONT VIEW Retrofit Box Presser Bar Needle Bar Hopping Foot Needle Part What it does Front Handles The handles are eguipped with push button stitches allowing two button selections The buttons in the handles can be customized to your preferred settings Light Embedded in the handles the light illuminates the guilting area with natural LED or black light UV Presser Bar The presser bar holds the hopping foot and controls the hopping foot height and stroke Hopping Foot The hopping foot maintains the needle and fabric distance to create good stitches The shape makes it safe to guide the machine along the edge of a template or ruler Tablet The tab
19. retrofit module into place on the dock use a 3 32 hex wrench to tighten the two set screws on the front of the module These screws lock onto the alignment posts and secure the module onto the machine PN140 0007 Rev00 Vision M 2 0 User Manual 12 TABLET MOUNT INSTALLATION 1 Using a 5 64 hex wrench remove the four 6 32 x 3 8 screws from the Tablet Mount Block Set them aside for re installation in a later step 2 Remove the plastic cap from the end of the Tablet Mount and set it aside It will be re installed in a later step t y 0 a i g 4 X J 2 T Fa Fs j n A A Pai x PN140 0007 Rev00 Vision M 2 0 User Manual 13 3 Place the included rubber washer onto the top of the head around the hole where the stylus post was removed in the Preparation section step 4 Optionally you may also place the misalignment washers on top of the rubber washer This is only necessary if the mount appears tilted due to variations in the head casting 4 Place the tablet mount post onto the rubber washer PN140 0007 Rev00 Vision M 2 0 User Manual 14 Use 1 4 T handle hex wrench to tighten the screw that goes through the middle of the post into the head Use the alignment mark on the bottom of the post to help you align the mark with the head as you tighten Use an adjustable wrench to hold the flats on the shaft as you tighten the screw 6 PN140 0007 Rev00 V
20. source code that may accompany it In no event shall the publisher and the author be liable for any loss of profit or any other commercial damage caused or alleged to have been caused directly or indirectly by this document This manual outlines the steps required to install a Vision 2 retrofit onto existing Gammill Vision machines or Gammill machines that have been outfitted with the Gammill Vision In Home Retrofit previously N NOTICE If you do not have a Gammill Vision or machine with the Gammill Vision In Home Retrofit consult your local Gammill representative or Gammill factory technician for assistance PN140 0007 Rev00 Vision M 2 0 User Manual 2 TABLE OF CONTENTS Vision 2 0 Retrofit Front View mcn 7 Vision ZO Retront instalation Instr rOCtiOMS sssi EEE EE AAEE 8 Fe FA 11 UII 12 Tablet IS IOTIE 12 Side Plate Installation Optronal 0 18 ae eer te ee E ee ee 20 WS c 25 The Vision n ESF invitiamo Ei HNN HCA HRN RF CEFR EF ee FR UE FN EEF Y FN CF FU 26 30 sure 31 31 Regulate 00 000008 32 Coa UU Com RR NOE EHI MI AEG AEN 33 EYN FFY FN FARF NWN NO NEN NU 36 0 EY EF WY RF FAE EVE I NEU REF 38 BUTONG Autom
21. the head Note Front Dock and Handles removed in image for clarity 2 Remove the rubber gasket from the head and clean of all oils 3 26 or 3o Machines ONLY move the hole plug from the old side plate to the new one 4 Place the gasket onto the side plate and place them both onto the head PN140 0007 Rev00 Vision M 2 0 User Manual 18 5 Using a 3 32 hex wrench install the eight 18 and 22 machines or seven 26 and 30 machines 8 32 x 3 8 screws to secure the side plate to the head Note Front Dock and Handles removed in image for clarity 6 Turn the hand wheel by hand Verify that neither the gasket nor new side plate are rubbing the hand wheel as it is rotated If it does rub repeat Steps 1 6 adjusting where necessary to eliminate the issue 7 Install the stylus post removed in Preparation step 4 into the nut on the side plate Note Front Dock and Handles removed in image for clarity 8 Using an adjustable 7 16 wrench tighten the jam nut to secure the stylus post PN140 0007 Rev00 Vision M 2 0 User Manual 19 POWERING UP 6 Plug the power cord back into the rear of the machine Turn both power switches to the ON 1 position Observe that the power light on the retrofit module is lit If it is not lit turn the power switches OFF O and ensure that the retrofit module is properly installed onto the dock Turn the Samsung tablet on To do this press and hold the power butto
22. wi smell CONSTANT i 6 CONSTANT REGULATE Speed 40 12 5 1 Constant 50 0000 j 570 690 7Y D My Buttons MyStitch Select R Start Stop Stitching To cancel resetting the Stitch Timer e Touch Cancel button on the Stitch Timer window e Notice the window closes stitch Timer The total stitch time is 01 33 Reset the Stitch Timer Reset the Timer TIME IS DISPLAYED IN AN HH MM SS FORMAT WHERE HH IS THE NUMBER OF HOURS MM IS THE NUMBER OF MINUTES AND SS IS THE NUMBER OF SECONDS IF THE TIMER EXCEEDS 99 59 59 THE TIMER WILL AUTOMATICALLY RESET TO 00 00 PN140 0007 Rev00 Vision M 2 0 User Manual 49 STITCH COUNTER FUNCTION The Stitch Counter continually counts the number of stitches taken making it easy to track the number of stitches in a project 7 3 28 PM mi My Stitch Presets LJ Gammill Vision 2 Q r 20 Connected to GAMMILL VISION2 E18E REGULATE REGULATE CONSTANT 16 SPI Speed 25 Stitches per Inch Regulate 12 101 69000 Start Qoo My Stitch Buttons Adjust Setting Up Start Stop Stitching To reset the Stitch Counter e Touch the Stitch Timer icon e Notice a window appears asking if you are sure you want to reset the Stitch Timer E Stitch Counter The total stitch count is 570 Reset the Stitch Counter Cancel Reset the Counter PN140 0007 Re
23. 00 Vision M 2 0 User Manual 25 THE VISION 2 0 APPLICATION The main screen offers the most commonly used features at a finger s touch Notice this screen is broken down into four sections the title bar top ribbon mode section and the bottom ribbon Title Bar Top Ribbon 5 Ew _ Gammill Vision 2 0 v 20 Connected to GAMMILL VISION2 E18E My Stitch Presets REGULATE REGULATE CONSTANT 16 SPI Speed 25 Stitches per Inch Mode Section Regu late 1 2 101 0 69 A Start My Stitch Buttons Adjust Setting Up R Start Stop Stitching Bottom Ribbon The Title Bar contains the application title key quilting features used for specialty functions The Top Ribbon provides access to the menu quilting modes and My Stitch presets In the Mode Section the active stitching mode is displayed along with access to stitching adjustments such as speed and stitches per inch along with related features such as starting and stopping stitching The Bottom Ribbon accesses the My Stitch Buttons features PN140 0007 Rev00 Vision M 2 0 User Manual 26 Title Bar What you can do with it 5 Gammill Vision 2 Accesses the menu options for ud ME 1 specialized functions and contains a Connected to GAMMIUL WTSIDNZ DDBD MenuAccess p the connection status to the machine Sets needle position when stitching Needle Position stops to needle up or needle down
24. 0007 Rev00 Vision M 2 0 User Manual 102 To test the Needle Sensors e Touch the Start button ird BRFASU Service amp Maintenance 40 Connected to GAMMILL VISION2 DDBD 1 NEEDLE POSITION NEEDLE UP SENSOR NEEDLE DOWN SENSOR Stop Remove the thread and bobbin from the machine Press START The motor will run for 15 seconds then will automatically stop The readings above will change If a reading is red adjust the position of the associated Needle Position Sensor Up or Down on the Vision 2 machine After adjusting press START again to update the readings When both readings are green the sensors are properly adjusted Always press Stop before adjusting the sensors on the machine THE MACHINE WILL RUN AN AUTOMATED TEST AND STOP WHEN COMPLETE THE DISPLAY WILL SHOW THE VALUES FOR THE UP AND DOWN SENSORS AS WELL AS COLOR AND SYMBOLS TO SHOW IF THE VALUES ARE ACCEPTABLE OR NOT e Touch the Stop button to stop the test while running amp 1 12PM Service 8 Maintenance 40 Connected to GAMMILL VISION2 DDBD 1 NEEDLE POSITION 1 NEEDLE UP SENSOR NEEDLE DOWN SENSOR TAKING READING 0 06 Remove the thread and bobbin from the machine Press START The motor will run for 15 seconds then will 0 automatically stop The readings above will change If a reading is red adjust the position of the associated Needle Position Sensor Up or Down on the Vision 2 machine After adju
25. AT THE MOTOR SPEED REQUIRED TO MAINTAIN THE STITCHES PER INCH IF THIS RATE OF MOVEMENT IS ABOVE THE SET SPEED THE MACHINE OPERATES IN A REGULATED MODE PN140 0007 Rev00 Vision M 2 0 User Manual 34 AND MAINTAINS THE SET STITCHES PER INCH IF THE SPEED IS BELOW THE SET SPEED THEN THE MACHINE RUNS AT A CONSTANT MODE AT THE SPEED SETTING AS AN ADVANCED FEATURE THE POINT AT WHICH THE MACHINE SWITCHES FROM REGULATE TO CONSTANT CAN BE SELECTED INDEPENDENTLY FROM THE CONSTANT SPEED 68 EY 0 r My Stitch Presets Gammill Vision 2 20 Connected to GAMMILL VISION2 E18E COAST REGULATE REGULATE CONSTANT 16 SPI Speed 25 Stitches Switch Point per Inch Speed STITCHING MODE Coast Regulate 5 12 35 pe Go 7 My Stitch Buttons Adjust Setting Up Start Stop Stitching To enable the Coast Regulate Switch Point e Touch the Change Switch Point advanced button located below the words Coast Regulate in the Stitching Mode indicator in the white mode section e The switch point appears in the mode section To set the Coast Regulate Switch Point e Touch the plus or minus sign below the Switch Point indicator to adjust up or down To disable the Coast Regulate Switch Point gt Touch the Link Switch Point to Speed default button located below the words Coast Regulate in the Stitching Mode indicator in the mode section
26. E SPI 12 40 Automatic Tie Off Completed 01 32 566 0 69 Fy L My Stitch Buttons MyStitch Select Start Stop Stitching WHEN THE AUTOMATIC TIE OFF FUNCTION IS COMPLETE THE SCREEN WILL CHANGE TO SHOW IT IS COMPLETED BRIEFLY AND THEN CHANGE BACK TO THE MODE AND SETTINGS SELECTED PRIOR TO ENTERING THE AUTOMATIC TIE OFF FUNCTION PN140 0007 Rev00 Vision M 2 0 User Manual 47 STITCH TIMER FUNCTION The Stitch Timer function continually monitors the amount of time spent stitching making it easy to keep track of the time spent on a project F amp H3 28 PM Gamnmill Vision 2 0 20 to GAMMILL VISION2 E18E My Stitch Presets REGULATE REGULATE CONSTANT 16 SPI Speed 25 Stitches per Inch STITCHING MODE 1 2 Regulate 101 0 69 7v Siitch Buttons Adjust Setting Up Start Stop Stitching To reset the Stitch Timer e Touch the Stitch Timer icon e Notice a window appears asking if you are sure you want to reset the Stitch Timer e Touch the Reset the Timer button to reset the time Stitch Timer The total stitch time is 01 33 Reset the Stitch Timer Cancel Reset the Timer PN140 0007 Rev00 Vision M 2 0 User Manual 48 Notice the timer display resets to 00 00 Gammill Vision 2 20 Connected to GAMMILL VISION2 E18E My Stitch Presets
27. EAR OF THE MACHINE THE INTENSITY SPOT SIZE OF THE LASER IS ALSO USER ADJUSTABLE AND IS EXPLAINED IN THE LASER SETTINGS SECTION PN140 0007 Rev00 Vision M 2 0 User Manual 61 ADDITIONAL FEATURES FUTURE ENHANCEMENTS The Additional Features Indicator allows access to new features as they become available in future software updates At this time there are no additional features to access so the icon is not visible Lam 1 04 PM zi Gammill Vision 2 Q HA 20 Connected to GAMMILL VISION2 DDBD b 25 Vv a My Stitch Presets e sa CONSTANT CONSTANT REGULATE epee 12 SP Speed STITCHANG MODE p j Constant 50 8 055 129 7Y My Stitch Buttons Adjust Setting Up Start Stop Stitching PN140 0007 Rev00 Vision M 2 0 User Manual 62 MAIN MENU The Main Menu offers access to many of the settings and services not regularly used during quilting 38 Ew U My Stitch Presets zd ER REGULATE REGULATE CONSTANT 16 SPI Speed 25 Stitches per Inch STITCHING MODE 2 Regulate 101 0 69 A My Stitch Buttons Adjust Setting Up Start Stop Stitching To access the Main Menu e Touch the Menu button PN140 0007 Rev00 Vision M 2 0 User Manual 63 To select an item from the Main Menu e Touch desired selection Im 7 MM 4 02 PM Gammill Vision 2 20 Connected to GAMMILL VI
28. NG COMBINATION THAT IS AVAILABLE TO THE USER WHILE THE EXAMPLE IMAGE SHOWS TWO DIFFERENT MODES IT IS POSSIBLE TO SET BOTH PRESETS TO THE SAME MODE WITH DIFFERENT SETTINGS ETC THIS FEATURE IS LIMITED ONLY BY THE USER S IMAGINATION To access Help e Press the small gear above the My Stitch Preset buttons Ed 3 32 a Gammill Vision 2 J 20 Connected to GAMMILL VISION2 E18E My Stitch Presets CONSTANT CONSTANT REGULATE Speed 40 12 SPI STITCHING MODE Constant 50 8 00 48 496 610 97 My Stitch Buttons MyStitch Select Start Stop Stitching 3 36 PM My Stitch Presets You may save two different groups of stitch settings as your Presets First choose a stitch type Constant Regulate Coast Regulate or Baste Then choose stitch settings that you like To save the current stitch settings as a Preset Press and hold the Preset 1 or Preset 2 button for 2 seconds To recall the saved settings any time you like simply press the Preset 1 or Preset 2 button PN140 0007 Rev00 Vision M 2 0 User Manual 39 MY STITCH BUTTONS The Stitch Buttons feature offers adjustment while stitching fingertip access to key features and assistance with common functions Each of the two My Stitch Buttons can be customized and set to change functions and speeds on the fly as well as access key functions such as tie off Gammill Vision 2 Conn
29. REEN TO THE FACTORY DEFAULTS TO EXIT THE SCREEN WHEN YOU ARE FINISHED MAKING CHANGES PRESS THE LEFT ARROW AT THE TOP LEFT OF THE SCREEN PN140 0007 Rev00 Vision M 2 0 User Manual 74 NEEDLE SETTINGS Customize various aspects of the needle movement and functions by accessing the Needle Settings screen Gammill Vision 2 20 Connected to GAMMILL VISION2 DDBD Needle Positioning Speed General Baste Only 15 15 Reset to Defaults 0 Select the speeds used for needle position events This is used to adjust the stop position of the needle Adjust Needle Position Speed e Press the plus button to increase the needle to position faster e Press the minus button to adjust the needle to position slower e Note the General setting controls all stitching modes except basting e Note the Baste setting controls only the basting mode THIS IS AN ADVANCED SETTING AND THE VALUE IS NORMALLY REDUCED TO ACCOUNT FOR WEAR WITHIN A MACHINE AS THE MACHINE AGES IT IS NOT RECOMMENDED THAT YOU CHANGE THIS SETTING UNLESS DIRECTED BY A GAMMILL TECHNICIAN PN140 0007 Rev00 Vision M 2 0 User Manual 75 Gammill Vision 2 40 Connected GAMMILL VISION2 DDBD Needle Positioning Speed General Baste Only 15 15 CIE Reset to Defaults 1 Select the speeds used for needle position events This is used to adjust the stop position of the needle To Reset Defaults e Press the Reset t
30. SION2 E18E Gammill Vision 2 About this App Alerts Needle Settings Laser Settings Display Settings Service and Maintenance Bluetooth Setup Quick Start Manual DETAILS ON ALL OF THE SCREENS FOUND IN THIS MENU CAN BE FOUND IN THE SETTINGS AND OTHER SCREENS SECTION PN140 0007 Rev00 Vision M 2 0 User Manual 64 SETTINGS AND OTHER SCREENS GENERAL NAVIGATION To leave any secondary screen and return to the main screen press the left arrow in the top left corner of the screen About This App 2 O Gammill Vision 2 Application v 0 9 1 LOLO Android v 4 2 2 TM Bluetooth Module Firmware v R109 Z Motor Module Firmware v R106 Gammill Quilting Systems 1 800 659 8224 6 2014 Gammill Inc All Rights Reserved 1452 Gibson Street West Plains MO 65775 Patents Pending Check for Updates PN140 0007 Rev00 Vision M 2 0 User Manual 65 GAMMILL VISION 2 The Gammill Vision 2 selection is a placeholder for the main window As a result it appears to do nothing when selected This was reguired to properly set up the menu structure and is intentional ABOUT THIS APP Access the About This App selection to learn information about your current version of the Vision 2 0 application and check for software updates EN J So About This App 4 O Gammill Vision 2 Application v 0 9 1 LOLO Android v 4 2 2 TM Bluetooth Module Firmware v R109 Z Motor Module Firmware v R106 Gammill Quilting S
31. User Manual 33 COAST REGULATE MODE Coast Regulate Mode offers graceful transitions between large sweeping patterns and fill work By fluctuating between stitch regulation and constant speed the machine adjusts to the rate the head is moved providing the best of both worlds mim Gammill Vision 2 0 v 20 Connected to GAMMILL VISION2 E18E 0 My Stitch Presets d 3 29 ee e TT COAST REGULATE REGULATE CONSTANT 16 SPI Speed 25 d Stitches per Inch Speed STITCHING MODE Coast Regulate Change Switch Point advanced 0030 4484 0 69 My Stitch Buttons Start Adjust Setting Up Start Stop Stitching To engage Coast Regulate Mode Touch the Coast Regulate icon in the top ribbon e Notice stitching mode is indicated in the mode section in the middle of the screen To set Coast Regulate Mode e Touch the plus or minus sign under Stitches per Inch to adjust stitch length e Touch the plus or minus sign under Speed to adjust the stitching speed To adjust Coast Regulate Mode while quilting e Touch the plus or minus sign to increase or decrease speed while stitching or stitches per inch COAST REGULATE MODE FLUCTUATES AUTOMATICALLY BETWEEN CONSTANT AND REGULATED MODES THE SET SPEED AND STITCHES PER INCH ARE USED TO DECIDE WHICH MODE THE MACHINE WILL STITCH IN AS THE HEAD IS MOVED THE MACHINE CONTINUALLY LOOKS
32. e button e Notice that as the button is pressed the corresponding indicator turns green This verifies that all buttons are functioning properly Aid 4 06PM Service amp Maintenance Connected to GAMMILL VISION2 E18E BUTTONS amp SENSORS Encoder Position Handle Buttons Needle Position Thread Movement 30 Use the indicators on this screen to check the performance of the X and Y encoders the machine handle buttons the needle position sensors and the thread movement sensor The associated indicator should turn green when you move the guilting arm move the needle to its up and down limits and press any handle button on the Vision 2 machine The thread movement count should increase as the thread break wheel is turned To check the Needle Position e Slowly turn the hand wheel by hand e Observe if the Up and Down needle position sensors turn green and that they turn green at the correct needle positions Service amp Maintenance Connected to GAMMILL VISION2 E18E BUTTONS amp SENSORS Encoder Position Handle Buttons Needle Position Thread Movement Use the indicators on this screen to check the performance of the X and Y encoders the machine handle buttons the needle position sensors and the thread movement sensor The associated indicator should turn green when you move the quilting arm move the needle to its up and down limits and press any handle button on the Vision 2 machine The thread
33. e left will lower the volume e Dragging the slider to the right will increase the volume 1 08 PM Gammill Vision 2 40 Connected to GAMMILL VISIOb Thread Break Bobbin Empty Alert Over Speed Alert Thread Break Alert 5 wn sensor Delay 5 O50 Wb 5 Reset to Defaults Move the volume slider to adjust the volume of the audible alerts Press the icons to enable or disable the pop up message and audible alert for these three alerts Adjust the Thread Break Sensor to change the sensitivity of the Thread Break Alert PN140 0007 Rev00 Vision M 2 0 User Manual 72 To disable an alert e Touch alerticon e With each press the alarm will toggle between on and off Notice the indicator below the alarm icon indicates whether it is on or off ES 1 08 PM T Gammill Vision 2 40 Connected to GAMMILL VISION2 DDBD Alert Volume Level e ID gt Thread Break Bobbin Empty Alert Over Speed Alert Thread Break Alert P Sensor Delay Reset to Defaults Move the volume slider to adjust the volume of the audible alerts Press the icons to enable or disable the pop up message and audible alert for these three alerts Adjust the Thread Break Sensor to change the sensitivity of the Thread Break Alert To adjust the Thread Break Sensor Delay e Press the minus button to decrease the delay making the sensor more sensitive e Press the
34. e tab displayed will change EE Service amp Maintenance J20 Connected to 2 BUTTONS amp SENSORS Encoder Position Handle Buttons Needle Position Thread Movement Tt UP SENSOR COUNT 30 FRONT REAR DOWN SENSOR Use the indicators on this screen to check the performance of the X and Y encoders the machine handle buttons the needle position sensors and the thread movement sensor The associated indicator should turn green when you move the quilting arm move the needle to its up and down limits and press any handle button on the Vision 2 machine The thread movement count should increase as the thread break wheel is turned PN140 0007 Rev00 Vision M 2 0 User Manual 22 Remove thread from needle and take up lever if necessary Also remove the bobbin from the machine 12 13 Touch Calibrate A popup window will appear eun 4 04 Service amp Maintenance 40 Disconnected MOTOR OPERATION Calibration Manual Operation Speed 10 Speed 5 Sec stitch ms Forward O Reverse Calibrate 999 Remove the tnread and bobbin from the machine before using this screen Calibration press Calibrate and the motor will automatically be calibrated Manual Operation Select a Direction and Speed setting then press Start to turn the motor on The speed setting may also be changed while the motor is running Touch Start motor calibration on
35. ected to GAMMILL VISION2 E18E 0 My Stitch Presets gt CONSTANT CONSTANT REGULATE Speed 40 12 SPI Adjust Setting Up Speed arise Sn Down STITCHING MODE 5 0 Start Stop Stitching ONStant Single Stitch z Needle Position MyStitch Select 196 2 100 MyStitch Select Start Stop Stitching Each of the two buttons can be configured to any one of the following functions Function Function Description When pressed the setting of the current mode will be decreased by one increment If in Coast Regulate mode only the Speed setting will be decreased Adjust Setting Down Adjust Setting Up When pressed the setting of the current mode will be increased by one increment If in Coast Regulate mode only the Speed setting will be increased Needle Position If the needle is up when pressed the needle will move to the down position and vice versa When pressed again the needle will move back to the up position Single Stitch Start Stop Stitching Tie Off My Stitch Select PN140 0007 Rev00 When pressed the machine will take one stitch This starts or stops the machine from stitching One button must be set to this setting for the machine to function When pressed the machine will begin the tie off function When pressed the machine function will switch between the two My Stitch Presets If stitching the machine will not stop but will instantly
36. ete Time Remaining 0 00 Stage 2 Complete Stage 3 Complete Reset Start Stop 1 Remove thread and bobbin from machine Apply oil to the machine as directed in Vision 2 User Manual Press Start to run the motor and a 15 minute automatic process will spread the oil throughout the machine Press Stop if you want to pause the process Press Reset to end the oiling process early PN140 0007 Rev00 Vision M 2 0 User Manual 101 NEEDLE POSITION Automatically verify that the needle position sensors are working and adjusted properly by using the Needle Position tab Remove the thread and bobbin from the machine before using this screen Failure to do this could cause damage to the machine FH1 12PM Service amp Maintenance 20 Connected to GAMMILL VISION2 DDBD 1 NEEDLE POSITION NEEDLE UP SENSOR RP NEEDLE DOWN SENSOR Start Stop Remove the thread and bobbin from the machine Press START The motor will run for 15 seconds then will 1 automatically stop The readings above will change If a reading is red adjust the position of the associated Needle Position Sensor Up or Down on the Vision 2 machine After adjusting press START again to update the readings When both readings are green the sensors are properly adjusted Always press Stop before adjusting the sensors on CAUTION Moving needle can cause injury Keep body parts and loose clothing away PN140
37. etup Quick Start Manual THESE SCREENS ARE USED WHEN DIAGNOSING POSSIBLE ISSUES WITH YOUR GAMMILL VISION 2 MACHINE NORMALLY THEY ARE BE USED UNDER THE DIRECTION OF A TECHNICIAN BUT NO HARM CAN COME TO THE MACHINE AS LONG AS YOU FOLLOW THE DIRECTIONS PN140 0007 Rev00 Vision M 2 0 User Manual 95 a 4 06 PM aa Service amp Maintenance 20 Connected to GAMM M BUTTONS amp SENSORS Encoder Position Handle Buttons Needle Position Thread Movement UP SENSOR COUNT 30 DOWN SENSOR Use the indicators on this screen to check the performance of the X and Y encoders the machine handle buttons the needle position sensors and the thread movement sensor The associated indicator should turn green when you move the guilting arm move the needle to its up and down limits and press any handle button on the Vision 2 machine The thread movement count should increase as the thread break wheel is turned PN140 0007 Rev00 Vision M 2 0 User Manual 86 BUTTONS AND SENSORS The Buttons and Sensors tab allows you to identify issues with the various sensors and buttons on the machine AES 9 Service amp Maintenance O Connected to GAMMILL VISION2 E18E BUTTONS amp SENSORS Encoder Position Handle Buttons Needle Position Thread Movement UP SENSOR COUNT FRONT REAR 6 0 J DOWN SENSOR 0 Use the indicators on this screen to check the performance of the X and
38. h the Stop button to stop the oiling routine ri Service amp Maintenance Jf20 Connected to GAMMILL VISION2 DDBD OILING Stage 1 Time Remaining 12 16 i Remove the thread and bobbin from the machine Apply oil to the machine as directed in the Vision 2 User Manual Press Start to run the motor and a 15 minute automatic process will spread the oil throughout the machine Press Stop if you want to pause the process Press Reset to end the oiling process early PN140 0007 Rev00 Vision M 2 0 User Manual 99 e Touch the Start button to resume to continue the oiling routing e Touch Reset button to begin from the beginning of the oiling routine 1 45 Service amp Maintenance 20 Connected to GAMMILL VISION2 DDBD wv Stage 1 Complete Time Remaining Stage 2 Complete 0 00 Stage 3 Complete Reset Start Stop 0 Remove the thread and bobbin from the machine Apply oil to the machine as directed in the Vision 2 User Manual Press Start to run the motor and a 15 minute automatic process will spread the oil throughout the machine Press Stop if you want to pause the process Press Reset to end the oiling process early PN140 0007 Rev00 Vision M 2 0 User Manual 100 To exit and return to the main screen press the left arrow at the top left of the screen Ole Fm 1 45PM Service amp Maintenance 20 Connected to GAMMILL VISION2 DDBD v OILING Stage 1 Compl
39. ile the motor is running _ A popup will appear to confirm you are ready to begin calibration If so press Start Motor Calibration e If not press Cancel gt M1 10 PM Remove the thread and bobbin from the machine The motor will run for approximately 40 seconds Are you ready to start the motor calibration Cancel Start motor calibration PN140 0007 Rev00 Vision M 2 0 User Manual 93 The calibration routine will run automatically displaying results as it progresses 5 25 4 04 PM Service amp Maintenance 20 Connected to GAMMILL VISION2 DDBD MOTOR OPERATION Calibration Speed 926 Sec stitch ms 19 172 41 86 21 50 40 16 26 60 Calibrate Reset 0 Remove the thread and bobbin from the machine before using this screen Calibration press Calibrate and the motor will automatically be calibrated Manual Operation Select a Direction and Speed setting then press Start to turn the motor on The speed setting may also be changed while the motor is running PN140 0007 Rev00 Vision M 2 0 User Manual 94 COMMUNICATIONS Use the communications tab to verify that the internal machine communications are working properly CD R 8 19 AM Service amp Maintenance 40 Connected to GAMMILL VISION2 E18E COMMUNICATIONS Z Drive gt Encoder Board gt Sensor Board 0 Select items above then press Scan to run an automatic check of the machine s electronic communicat
40. ions THIS SCREEN IS USEFUL TO DIAGNOSE AN INTERMITTENT CONNECTION PROBLEM WITHIN THE MACHINE OR A CIRCUIT BOARD THAT MAY BE FAILING To test Communications Notice boxes beside each of the communication systems to test is already checked e Touch the box beside any of the systems you do not wish to test Leave all of the boxes checked to check the entire communication system Service amp Maintenance 40 Connected to GAMMILL VISION2 E18E COMMUNICATIONS Z Drive gt Encoder Board v Sensor Board Select items above then press Scan to run an automatic check of the machine s electronic communications PN140 0007 Rev00 Vision M 2 0 User Manual 95 e Pressthe Scan button i Service amp Maintenance 20 Connected to GAMMILL VISION2 E18E COMMUNICATIONS Z Drive Encoder 20870 bd Sensor Board o Select items above then press Scan to run an automatic check of the machine s electronic communications e The test will automatically run showing progress and results The messages received should be equal to the messages sent If they are not egual communication was lost between the device and the Bluetooth module 3E _ 8 20 AM 7 Service amp Maintenance Connected to GAMMILL VISION2 E18E E COMMUNICATIONS Messages Sent 1000 Messages Received 1000 Messages Sent 1000 Messages Received 1000 S B Messages Sent 1000 ensor Messages Received 1000
41. ision M 2 0 User Manual 15 7 Using a 5 64 hex wrench install the four 6 32 x 3 8 screws removed in step 1 of this section to secure the plastic tablet holder to the mounting block 8 Remove the Samsung Galaxy Tab 3 tablet from its packaging 9 Install the tablet into the holder Place the bottom of the tablet into the holder first and rock it rearward until it is locked into place PN140 0007 Rev00 Vision M 2 0 User Manual 16 10 Plug the black 18 USB charging cable into the USB port on the side of the retrofit module and into the bottom of the tablet Ensure the cable does not contact rotating components etc securing it as necessary E 1 ED 1 i l k AI j a 00 0 0 5 M ee A Ere YR LU 5 xm 1 x 0 a gt T MN 1 ir 1 i zi th zi y sa 3 he PN140 0007 Rev00 Vision M 2 0 User Manual 17 SIDE PLATE INSTALLATION OPTIONAL This section is optional you did not utilize the stylus post that was NOTICE removed in Preparation step 4 to use a laser at the front of the machine this section may be skipped Please store the parts for later use in case your needs change 1 Using a 3 32 hex wrench remove the eight 18 and 22 machines or seven 26 and 30 machines 8 32 x 3 8 screws that secure the side plate to
42. let contains the Vision 2 0 Android App that communicates with the machine Needle Bar The needle bar holds the needle and maintains the needle height to create good stitches Needle The needle carries the thread through the fabric Retrofit Module Replaces the main module as the brains of the machine Interfaces to the tablet via Bluetooth PN140 0007 Rev00 Vision M 2 0 User Manual 7 VISION 2 0 RETROFIT INSTALLATION INSTRUCTIONS Welcome to the Vision 2 0 Retrofit Take the current Gammill Vision handguided longarm quilting system to a new level of functionality and customizability with the new features offered by the Vision 2 0 Retrofit This retrofit is designed to be installed by the user with these simple instructions IMPORTANT NOTICE THE VISION 2 0 RETROFIT WORKS WITH THE CURRENT MODULE DOCK WITH TWO PROTRUDING PINS ANY PREVIOUS DOCKS ARE NOT COMPATIBLE RETROFITTING THE GAMMILL VISION9 MAY BE REVERSED IF DESIRED SIMPLY REVERSE THE INSTALLATION INSTRUCTIONS PRESENTED HERE IN THIS GUIDE PN140 0007 Rev00 Vision M 2 0 User Manual 9 PARTS REOUIRED INCLUDED IN KIT m ry s 0 1 F 5 1 7 1 25 r One 1 Misalignment Washer Set Installation Optional Ua One 1 Tablet Mount One 1 Rubber Washer Vision M 2 0 User Manual PN140 0007 Rev00 Parts Reguired Included in Kit Continued 70 fo
43. mill Vision 2 v 20 Connected to GAMMILL VISION2 E18E My Stitch Presets REGULATE REGULATE CONSTANT 16 SPI Speed 25 Stitches per Inch STITCHING MODE 1 2 Regulate Start 101 0 69 9 My Stitch Buttons Adjust Setting Up Start Stop Stitching To stop stitching with the needle down Tap the Needle Stop Position icon so the needle indicates the down position e Notice when stitching stops the needle stops in the down position To stop stitching with the needle up e Needle Stop Position icon so the needle indicates the up position e Notice when stitching stops the needle stops in the up position WHEN USING THE NEEDLE DOWN POSITION USE OF A SINGLE STITCH WILL RESULT IN THE NEEDLE STOPPING IN THE UP POSITION FOR THE FIRST PRESS SUBSEQUENT PRESSES OF THE SINGLE STITCH BUTTON WILL RESULT IN FULL STITCHES TAKEN PN140 0007 Rev00 Vision M 2 0 User Manual 57 HORIZONTAL CHANNEL LOCK The Horizontal Channel Lock Icon limits the motion of the machine to a horizontal direction not allowing any vertical movement This feature aids in creating perfectly straight lines whether for basting or stitching 3 28 Gammill Vision 2 09 EA vt 20 Connected to GAMMILL VISION2 E18E My Stitch Presets ee REGULATE CONSTANT REGULATE 16 SPI Speed 5 Stitches per Inch Regulate 12 e
44. movement count should increase as the thread break wheel is turned PN140 0007 Rev00 Vision M 2 0 User Manual 88 To check Thread Movement e Turn the thread break wheel 4 06 PM Service amp Maintenance Connected to GAMMILL BUTTONS amp SENSORS Encoder Position Handle Buttons Needle Position Thread Movement 30 Use the indicators on this screen to check the performance of the X and Y encoders the machine handle buttons the needle position sensors and the thread movement sensor The associated indicator should turn green when you move the guilting arm move the needle to its up and down limits and press any handle button on the Vision 2 machine The thread movement count should increase as the thread break wheel is turned THE THREAD MOVEMENT COUNT WILL EITHER INCREASE OR DECREASE DEPENDING ON DIRECTION ROTATED BY 12 FOR EACH ROTATION OF THE WHEEL THIS VERIFIES THAT THE THREAD BREAK ENCODER IS WORKING PROPERLY To exit Buttons and Sensors e Touch the left arrow at the top left of the screen 4 06 PM g Service amp Maintenance M20 Connected to GAMMILL VISION2 E18E P BUTTONS amp SENSORS Encoder Position Handle Buttons Needle Position Thread Movement 30 Use the indicators on this screen to check the performance of the X and Y encoders the machine handle buttons the needle position sensors and the thread movement sensor The associated indicator should turn green
45. n upper left corner until you see a logo on the screen Once the tablet is fully booted touch the Gammill Vision 2 icon on the home screen to open the app Touch the Menu button on the upper left of the screen 2 My Stitch Presets CONSTANT CONSTANT REGULATE Speed 4t 12 SPI PN140 0007 Rev00 Vision M 2 0 User Manual 20 7 Touch Bluetooth Setup Gammill Vision 2 40 Connected to GAMMILL VISION2 E18E About this App Alerts Needle Settings Laser Settings Display Settings Service and Maintenance Bluetooth Setup Quick Start Manual 8 Touch the address of your machine from the list If you have multiple machines the listing consult the address recorded in step 1 on page 12 It is four digits and may consist of numbers and capital letters I E FBBD DCAA etc The tablet will be connected to the machine Choose Bluetooth Device GAMMILL VISION2 DDBD Cancel 9 Touch the Menu button on the upper left of the screen My Stitch Presets m CONSTANT REGULATE Speed 40 12 SPI PN140 0007 Rev00 Vision M 2 0 User Manual 21 10 _ Touch Service and Maintenance The screen will change to the Service and Maintenance screens ES 84 02PM Gammill Vision 2 20 Connected to GAMMILL VISION2 E18E Needle Settings Laser Settings Display Settings Service and Maintenance 7 Bluetooth Setup 11 Touch the Motor Operation tab Th
46. n 2 0 0 20 Connected to GAMMILL VISION2 E18E 0 My Stitch Presets CONSTANT REGULATE Speed 40 12 SPI Stitches Number of per Inch Stitches Automatic Tie Off Reset to Defaults lt Cancel 20 6 ERE MyStitch Select Start Stop Stitching 0048 6 100 Fyre My Stitch Buttons To access the Automatic Tie Off e Touch tied bow icon to access tie off mode Gammill Vision 2 20 Connected to GAMMILL VISION2 E18E le My Stitch Presets REGULATE REGULATE CONSTANT 16 SPI Speed 25 Stitches per Inch Regulate 12 00 09 My Stitch Buttons y 101 Adjust Setting Up R Start Stop Stitching PN140 0007 Rev00 Vision M 2 0 User Manual 43 e Notice stitching mode changes to Automatic Tie Off in the mode section in the middle of the screen and the tied bow indicates the number of stitches left in the tie off To set the Automatic Tie Off e Touch the plus or minus sign below Stitches per Inch to adjust the stitch length The Stitches per Inch may be adjusted from 12 to 6o e Touch the plus or minus sign below Number of Stitches to adjust the number of stitches used in the tie off The Number of Stitches may be adjusted from 2 to 15 38 PM Od My Stitch Presets Gammill Vision 2 20 Connected to GAMMILL VISION2 E18E CONSTANT REGULATE
47. ncrease brightness and increase the size of the laser point e Press the minus to decrease brightness and decrease the size of the laser point Gammill Vision 2 420 Connected to GAMMILL VISION2 DDBD Laser On Off Brightness 10 Reset to Defaults Adjust the laser s brightness so that it is easy to see in your room s lighting Turning the laser on will allow you to see the laser s brightness change while you make the adjustment PN140 0007 Rev00 Vision M 2 0 User Manual 78 To reset defaults e Touch the Reset to Defaults button to reset all settings on this screen to the factory defaults Laser On Off Brightness Q Reset to Defaults 0 Adjust the laser s brightness so that is easy to see in your room s lighting Turning the laser on will allow you to see the laser s brightness change while you make the adjustment EXIT THE SCREEN WHEN YOU ARE FINISHED MAKING CHANGES PRESS THELEFT ARROW AT THE TOP LEFT OF THE SCREEN PN140 0007 Rev00 Vision M 2 0 User Manual 79 DISPLAY SETTINGS Select the color used on the colored bars of the main screen in the Display Settings screen 1 09 PM Gammill Vision 2 20 Connected to GAMMILL VISION2 DDBD Main Screen Color Theme Choose a background color theme Purple Blue Green Pink Gray Reset to Defaults Touch color option above to customize the color theme of your main guilti
48. ng press START again to update the readings When both readings are green the sensors are properly adjusted Always press Stop before adjusting the sensors on the machine PN140 0007 Rev00 Vision M 2 0 User Manual 104
49. ng screen To select a color e Touch a colored box 1 08 PM Gammill Vision 2 2O Connected to GAMMILL VISION2 DDBD Main Screen Color Theme Choose a background color theme Purple Blue Green Pink Gray Reset to Defaults i Touch a color option above to customize the color theme of your main guilting screen PN140 0007 Rev00 Vision M 2 0 User Manual 80 e Touch the Reset to Defaults button to reset the main screen color to purple el mm m 7 1 09 Gammill Vision 2 20 Connected to GAMMILL VISION2 DDBD Main Screen Color Theme Choose a background color theme Purple Blue Green Pink Gray Reset to Defaults 0 Touch a color option above to customize the color theme of your main guilting screen To exit the screen press the left arrow at the top left of the screen CD ap Gammill Vision 2 20 Connected to GAMMILL VISION2 DDBD Main Screen Color Theme Choose a background color theme Purple Blue Green Pink Gray Reset to Defaults 0 Touch a color option above to customize the color theme of your main guilting screen PN140 0007 Rev00 Vision M 2 0 User Manual 91 BLUETOOTH SETUP The Bluetooth Setup allows the user to connect the tablet user interface to a machine When chosen a popup window will appear This popup window will display all the available machines identified by the software GAMMILL VISION2 E18E TOUCH THE LISTING FOR THE MACHINE YOU WANT TO CONNECT
50. ning 15 00 Reset Start Stop Remove the thread and bobbin from the machine Apply oil to the machine as directed in the Vision 2 User Manual Press Start to run the motor and a 15 minute automatic process will spread the oil throughout the machine Press Stop if you want to pause the process Press Reset to end the oiling process early THE OILING ROUTINE IS A WAY TO RUN THE MACHINE THROUGH A 15 MINUTE OILING ROUTINE DURING THIS ROUTINE THE MACHINE WILL RUN 5 MINUTES IN FORWARD 5 MINUTES IN REVERSE AND 5 MINUTES IN FORWARD CAUTION Moving needle can cause injury Keep body parts and loose clothing away To run the Oil Routine PN140 0007 Rev00 Vision M 2 0 User Manual 98 e all oiling points on the machine See Oiling Instructions on page 11 e Touch the Start button 12 v Service amp Maintenance 4 20 Connected to GAMMILL VISION2 DDBD OILING Time Remaining 15 00 Reset Stop Remove the thread and bobbin from the machine Apply oil to the machine as directed in the Vision 2 User Manual Press Start to run the motor and a 15 minute automatic process will spread the oil throughout the machine Press Stop if you want to pause the process Press Reset to end the oiling process early gt The machine will go through the routine and show the progress When the routine is complete the machine will automatically stop running To Stop and Resume the Oiling Routine e Touc
51. o Defaults button to reset all settings on this screen to the factory defaults EXIT THE SCREEN WHEN YOU ARE FINISHED MAKING CHANGES PRESS THELEFT ARROW AT THE TOP LEFT OF THE SCREEN PN140 0007 Rev00 Vision M 2 0 User Manual 76 LASER SETTINGS Adjust the intensity of the laser to compensate for your room s brightness as well as to change the size of the laser dot TEE 1 08 Gammill Vision 2 40 Connected to GAMMILL VISION2 DDBD L On Off A Brightness 10 E Reset to Defaults Adjust the laser s brightness so that it is easy to see in your room s lighting Turning the laser on will allow you to see the laser s brightness change while you make the adjustment Laser Radiation Avoid direct exposure to beam To turn the laser on or off e Press Laser On Off button to turn the laser on Notice the indicator below the laser icon indicates whether it is on or off e Press the Laser On Off button to turn the laser off PN140 0007 Rev00 Vision M 2 0 User Manual 77 1 06 PM Gammill Vision 2 20 Connected GAMMILL VISION2 DDBD Laser On Off Brightness Reset to Defaults i Adjust the laser s brightness so that it is easy to see in your room s lighting Turning the laser on will allow you to see the laser s brightness change while you make the adjustment To adjust the laser brightness e Press the plus to i
52. sting press START again to update the readings When both readings are green the sensors are properly adjusted Always press Stop before adjusting the sensors on the machine PN140 0007 Rev00 Vision M 2 0 User Manual 103 e Touch the Start button to restart the test 1 38 PM 7 Service amp Maintenance 4 20 Connected to GAMMILL VISION2 DDBB 1 MEEDLE POSITION T NEEDLE UP SENSOR NEEDLE DOWN SENSOR Start Stop Remove the thread and bobbin from the machine Press START The motor will run for 15 seconds then will automatically stop The readings above will change If a reading is red adjust the position of the associated Needle Position Sensor Up or Down on the Vision 2 machine After adjusting press START again to update the readings When both readings are green the sensors are properly adjusted Always press Stop before adjusting the sensors on the machine To exit and return to the main screen press the left arrow at the top left of the screen 5 Service amp Maintenance 20 Connected to GAMMILL VISION2 DDBD 1 NEEDLE POSITION T NEEDLE UP SENSOR HEEDLE DOWN SENSOR Start Stop Remove the thread and bobbin from the machine Press START The motor will run for 15 seconds then will automatically stop The readings above will change If a reading is red adjust the position of the associated Needle Position Sensor Up or Down on the Vision 2 machine After adjusti
53. switch between the two modes Vision M 2 0 User Manual 40 EACH BUTTON PERFORMS THE SAME FUNCTION WHETHER STITCHING IS STARTED OR STOPPED HOWEVER SOME FUNCTIONS SUCH AS NEEDLE POSITION AND SINGLE STICH ARE DISABLED ONCE STITCHING IS STARTED LOCKING THE BUTTON ASSIGNMENTS PREVENTS THEM FROM EASILY BEING Locking the My Stitch Buttons e Touch the small gear beside the My Stitch Buttons e Gammill Vision 2 ch E 40 Connected to GAMMILL VISION2 E18E y le My Stitch Presets ena REGULATE REGULATE CONSTANT 16 SPI Speed 5 Stitches per Inch STITCHING MODE Regulate 12 oo F101 TF p NN My Stitch Buttons 1 Adjust Setting Up R Start Stop Stitching PN140 0007 Rev00 Vision M 2 0 User Manual 41 e Touch the box to select the option to lock the button assignments PN140 0007 Rev00 PM My Stitch Buttons You may assign different functions to the handle buttons on your Gammill Vision 2 Touch the button on the tablet screen then choose an option from the menu that appears At least one of the buttons must be assigned to the option Start Stop Stitching jk my button assignments so they can t be changed Vision M 2 0 User Manual 42 AUTOMATIC TIE OFF FUNCTION Secure stitching with the Automatic Tie Off function that delivers a set number of stitches at a preselected density mim Gammill Visio
54. tally To disengage the Vertical Channel Lock Tap closed Vertical Channel Lock icon e Notice the icon unlocks indicating the channel lock is disengaged and the machine moves freely in all directions PN140 0007 Rev00 Vision M 2 0 User Manual 59 LASER The Laser icon turns the laser on or off with the tap of a finger Laser Radiation Avoid direct exposure to beam Gai 03 28 X Gammill Vision 2 9 A 20 Connected to GAMMILL VISION2 E18E My Stitch Presets REGULATE REGULATE CONSTANT 16 SPI Speed 25 Stitches per Inch Regulate 12 Start O 7 0 69 101 My Stitch Buttons Adjust Setting Up R Start Stop Stitching To turn the laser on e Touch greyed Laser icon Notice laser on the Laser icon turns red indicating that the laser is on To turn the laser off e Touch the red Laser icon e Notice the laser on the Laser icon turns grey indicating that the laser is off PN140 0007 Rev00 Vision M 2 0 User Manual 60 Gammill Vision 2 20 Connected to GAMMILL VISION2 E18E My Stitch Presets ee REGULATE REGULATE CONSTANT 16 SPI Speed 25 Stitches per Inch STITCHING MODE 1 2 Regulate 101 0 69 A My Stitch Buttons Adjust Setting Up R Start Stop Stitching THIS FUNCTION CONTROLS THE LASER WHETHER PLUGGED IN TO THE FRONT OR R
55. tch Select Start Stop Stitching PN140 0007 Rev00 Vision M 2 0 User Manual 45 To execute an Automatic Tie Off e Touch the Start button on the screen e _ Or press the handle button set to start stop stitching rmm Gamnmill Vision 2 0 r vt 420 Connected to GAMMILL VISION2 E18E My Stitch Presets d 3 39 PM CONSTANT REGULATE Speed 40 12 SPI Stitches Number of per Inch Stitches Automatic Tie Off 20 6 Reset 10 Defaults Cancel 00 48 100 My Stitch Buttons MyStitch Select Start Stop Stitching Move the head Notice the machine begins stitching as soon as the head moves The number beside the tied bow also counts down as the stitches are delivered PN140 0007 Rev00 Vision M 2 0 User Manual 46 a Gammill Vision 2 40 Connected to GAMMILL VISION2 E18E r My Stitch Presets CONSTANT REGULATE Speed 40 12 SPI Automatic Tie Off Applying stitches 01 21 528 100 2 TN r My Stitch Buttons MyStitch Select Start Stop Stitching IF THE RED STOP BUTTON IS PRESSED DURING A TIE OFF THE CURRENT TIE OFF WILL STOP BUT WILL NOT LEAVE THE TIE OFF MODE IF THE GREEN START BUTTON IS PUSHED AGAIN THE TIE OFF WILL START OVER RATHER THAN PICKING UP WHERE STOPPED 7 Gammill Vision 2 Q cf v 40 Connected to GAMMILL VISION2 E18E M Za My Stitch Presets CONSTANT REGULAT
56. th it m M My Stitch Assigns functions to each of the four o My Buttons Buttons A D handle buttons IF THE TOUCH SCREEN SEEMS LESS SENSITIVE AFTER A WHILE REBOOT THE TABLET BY PRESSING AND HOLDING THE TABLET POWER BUTTON SELECT RESTART FROM THE WINDOW ONCE RESTARTED REOPEN THE APP BY TOUCHING THE ICON WHEN TURNING OFF THE MACHINE PUT THE TABLET TO SLEEP BY PRESSING THE BUTTON ON THE TOP LEFT EDGE OF THE TABLET IF THE TABLET IS LEFT ON WITH THE MACHINE OFF THE TABLET BATTERY WILL BE DEPLETED OUICKLY PN140 0007 Rev00 Vision M 2 0 User Manual 29 STITCHING Moving needle can cause injury Keep body parts and loose clothing away To begin and end stitching there are several options available Start and Stop On screen Buttons e Select the green START button located in the bottom right mode portion of the screen to enable stitching using the main screen To stop select the red STOP button located in the same area 600812 s Go 7 690812 696 F f so Handle Button e Usethe My Stitch feature to program any handle button to control stitch starting and stopping to match your needs The Start Stop Stitching control can be assigned to any of the two buttons but one must be set to Start Stop Stitching My Stitch Buttons Adjust Setting Up Start Stop Stitching e Press the handle button assigned to start or stop stitching to engage and disengage stitching SIDE NOTE
57. the popup window A calibration routine will be run on your motor This is used to improve the accuracy of stitch regulation The test will run for approximately 40 seconds and automatically stop when complete 14 Are rm VI O L LJ 1 L Ul Remove the thread and bobbin from the machine The motor will run for approximately 40 seconds Are you ready to start the motor calibration Cancel Start motor calibration PN140 0007 Rev00 Vision M 2 0 User Manual 23 15 _ Once calibration is complete touch the icon in the upper left corner of the screen to return to the main screen Sdrvice amp Maintenance Connected to GAMMILL VISIONZ DDBD 16 Installation is complete Enjoy your new Vision 2 0 retrofit PN140 0007 Rev00 Vision M 2 0 User Manual 24 THE TABLET SEE THE SAMSUNG TAB 3 OUICK START GUIDE FOUND IN THE TABLET BOX FOR BASIC TABLET INFORMATION 11 09 AM 40 Gammill Vist Settings My Files Find the Vision 2 0 Application Icon on the tablet Home Screen and tap to launch it It can also be found on the app screen Samsung Tablet Updates SAMSUNG WILL REGULARLY PUSH UPDATES FOR THE TABLET WE RECOMMEND THAT YOU DO NOT INSTALL THESE UPDATES UNTIL WE PUT A NOTICE ON THE GAMMILL WEBSITE RECOMMENDING YOU DO SO THIS WILL GIVE US TIME TO CHECK THE UPDATE TO SEE HOW IT WILL INTERACT WITH OUR APPLICATION AND YOUR VISION 2 0 SYSTEM PN140 0007 Rev
58. tion Speed Sec stitch ms O Forward O Reverse Calibrate 6 Start Stop Remove the thread and bobbin from the machine before using this screen Calibration press Calibrate and the motor will automatically be calibrated Manual Operation Select a Direction and Speed setting then press Start to turn the motor on The speed setting may also be changed while the motor is running e Press the minus or plus to select the speed to run at Service amp Maintenance 20 Connected to GAMMILL VISION2 E18E MOTOR OPERATION Calibration Manual Operation Speed Sec stitch ms Speed y 0 O Forward O Reverse Calibrate 6 Start Stop Remove the thread and bobbin from the machine before using this screen Calibration press Calibrate and the motor will automatically be calibrated Manual Operation Select a Direction and Speed setting then press Start to turn the motor on The speed setting may also be changed while the motor is running PN140 0007 Rev00 Vision M 2 0 User Manual 91 gt n 1 35 a Service amp Maintenance Connected to GAMMILL VISION2 DDBB MOTOR OPERATION Calibration Manual Operation Speed 5 Sec stitch ms Speed 2 0 Forward Reverse Calibrate 1996 Stop 1 Remove thread and bobbin from the machine before using this screen Calibration press Calibrate and the motor will automatically be calibrated Manual Operation Select a Direc
59. tion and Speed setting then press Start to turn the motor on The speed setting may also be changed while the motor is running e Press the Start button on the screen e When you are ready to stop running press the Stop button 7 Service Maintenance 40 Connected to GAMMILL VISION2 DDBB MOTOR OPERATIOM Manual Operation 4 Speed O Forward 2 O Reverse Start Remove the thread and bobbin from the machine before using this screen Calibration press Calibrate and the motor will automatically be calibrated Manual Operation Select a Direction and Speed setting then press Start to turn the motor on The speed setting may also be changed while the motor is running THE SPEED MAY BE ADJUSTED WHILE RUNNING BUT THE MOTOR MUST BE STOPPED TO CHANGE THE DIRECTION PN140 0007 Rev00 Vision M 2 0 User Manual 92 To initiate the motor calibration routine e Press the Calibrate button on the screen F 1 35 Service amp Maintenance 40 Connected to GAMMILL VISION2 DDBB MOTOR OPERATION Calibration Manual Operation Speed Sec stitch ms Speed O Forward 20 O Reverse Calibrate 6 Start Stop 1 Remove thread and bobbin from the machine before using this screen Calibration press Calibrate and the motor will automatically be calibrated Manual Operation Select a Direction and Speed setting then press Start to turn the motor on The speed setting may also be changed wh
60. v00 Vision M 2 0 User Manual 50 Tap Reset the Counter button to reset the count e Notice count display resets to o To cancel resetting the Stitch Counter Tap the Cancel button on the Stitch Counter window e Notice the window closes THIS INDICATOR DISPLAYS THE NUMBER OF STITCHES TAKEN WITH A MAXIMUM OF 999 999 ALLOWED AT THIS POINT THE INDICATOR WILL AUTOMATICALLY RESET TO o PN140 0007 Rev00 Vision M 2 0 User Manual 51 BOBBIN GAUGE FUNCTION The Bobbin Gauge function monitors the amount of top thread used to estimate usage of the bobbin thread displaying a percentage of the amount of the bobbin thread remaining Ew vt My Stitch Presets Gammill Vision 2 Q r 20 Connected to GAMMILL VISION2 E18E REGULATE REGULATE CONSTANT 16 SPI Speed 25 Stitches per Inch Regulate 12 My Stitch Buttons Adjust Setting Up Start Stop Stitching To use the Bobbin Gauge Tap Bobbin Gauge icon e Notice the Bobbin Gauge settings window appears Bobbin Gauge Thread Factor the Bobbin Gauge 1 0 4 Reset the Gauge PN140 0007 Rev00 Vision M 2 0 User Manual 52 Tapthe box beside the Use the Bobbin Gauge message e Notice a check mark appears indicating the Bobbin Gauge is active To set the Thread Factor e Touch the plus or minus sign to adjust the Thread Factor up or down The Thread Factor may
61. when you move the guilting arm move the needle to its up and down limits and press any handle button on the Vision 2 machine The thread movement count should increase as the thread break wheel is turned PN140 0007 Rev00 Vision M 2 0 User Manual 89 MOTOR OPERATION The Motor Operation tab contains the ability to manually operate the motor for troubleshooting purposes as well as initiate the motor calibration routine Remove the thread and bobbin from the machine before using this screen 6 Failure to do this could cause damage to the machine Service amp Maintenance 20 Connected to GAMMILL VISION2 E18E MOTOR OPERATION Calibration Manual Operation Speed 96 Sec stitch ms Speed y O Forward O Reverse Calibrate 999 Start Stop 0 Remove the thread and bobbin from the machine before using this screen Calibration press Calibrate and the motor will automatically be calibrated Manual Operation Select a Direction and Speed setting then press Start to turn the motor on The speed setting may also be changed while the motor is running CAUTION Moving needle can cause injury Keep body parts and loose clothing away PN140 0007 Rev00 Vision M 2 0 User Manual 90 To manually run the motor e Touch Forward or Reverse to select a direction 84 08 PM Service amp Maintenance 20 Connected to GAMMILL VISION2 E18E MOTOR OPERATION Calibration Manual Opera
62. ystems 1 800 659 8224 6 2014 Gammill Inc All Rights Reserved 1452 Gibson Street West Plains MO 65775 Patents Pending Check for Updates To check for updates e Make sure the tablet is connected to the internet e Touch the Check for Updates button e Notice an update window opens indicating whether or not an update is available THIS FUNCTION REQUIRES THE TABLET TO BE CONNECTED TO THE INTERNET THROUGH A USER SUPPLIED WIRELESS NETWORK FOR INFORMATION ON HOW TO DO THIS CONSULT THE DOCUMENTATION THAT CAME WITH THE TABLET PN140 0007 Rev00 Vision M 2 0 User Manual 66 Gammill Vision 2 Version 1 1 0 is available Do you want to download and install it nove NO To update the Vision 2 0 Application e Touch the YES button e Notice the update begins downloading e Please wait while the app is downloading from the Gammill website PN140 0007 Rev00 Vision M 2 0 User Manual 67 Downloading GammillVision2 v1 1 0 apk Please wait Cancel Download THE DOWNLOAD MAY BE CANCELLED AT ANYTIME BY PRESSING THE CANCEL DOWNLOAD BUTTON e Once downloaded a window will appear for permission to install the update 7 Gammill Vision 2 Do you want to install an update to this existing application Your existing data will not be lost The updated application will get access 10 WE This update requires no new permissions e Press Install to begin the update PN140 0007 Rev00 Vision M 2 0 User Manual

Download Pdf Manuals

Related Search

Related Contents

  Vibe Steam Mop  MagicSafe MSG150  LEICA M9  Datos técnicos S7-200    Guía de navegación del Aula Virtual  

Copyright © All rights reserved. Failed to retrieve file