Installation Manual Roof Zone Ladder Rack
Contents
1. please provide at a minimum the following information by calling 404 344 0000 e Model number serial number and all other data on the specific component which appears to be involved in the difficulty e The date and from whom you purchased your TIE DOWN product e State your difficulty being sure to mention at least the following Application Nature of load involved and Weight of the load Field Service If field service at the request of the purchaser is rendered and the difficulty is found not to be with TIE DOWN s product the purchaser shall pay the time and expense at the prevailing rate at the time of service of seller s field representative s Charges for service labor and other expenses that have been incurred by the purchaser its customer or agent without prior written authorization of TIE DOWN will not be accepted TIE DOWN EXTENDS NO WARRANTY EXPRESS OR IMPLIED ON PRODUCTS NOT MANUFACTURED BY TIE DOWN OR TO TIE DOWN S DESIGN SPECIFICATION INCLUDING BUT NOT LIMITED TO SUCH ITEMS AS NON TIE DOWN TIRES BRAKES ACTUATORS BEARINGS HOSE AND TUBING PURCHASER S RECOURSE SHALL BE LIMITED TO ANY WARRANTY OF THE RESPECTIVE MANUFACTURERS THIS WARRANTY EXCLUDES ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY PURPOSE THIS WARRANTY DOES NOT COVER NOR EXTEND TO INCIDENTAL OR CONSEQUENTIAL DAMAGE Some states do not allow the exclusion or limitation of incidental or consequential damages so the above2. 150 adaptor onto the front leg socket Do not tighten the thread cutting bolt at this time See Figure 2 1b Insert the front leg socket into the front mounting bracket as seen in Figure 1 Hold the mounting bracket flush with the top rail of the truck bed ensuring the front leg socket assembly is plumb and square to the truck bed This may also be mounted 90 degrees 1c Mark and center punch the four holes of the front mounting bracket and front leg socket foot as seen in Figure 1 NOTE If the best mounting hole location is between floor ribs a floor spacer and or two extra 5 16 flat washers have been provided to fill the void Or rotate the Leg Socket 90 to the rear of the vehicle if possible 1d Drill a pilot hole with a 7 32 drill bit in each marked hole Then re drill the holes with a 1 2 drill bit Apply silicone sealant around all drilled metal holes 1e Install rivnut fastener into each drilled hole see page 7 Figure 9 for rivnut fastener installation instructions 1f Take the front leg socket assembly four 5 16 18 x 1 1 4 hex head bolts four 5 16 lock washers and four 5 16 flat washers and install as seen in Figure 1 Tighten all screws at this point ensuring assembly is square and plumb to the truck 1g Take a 3 8 16 x 1 thread cutting bolt and install into the front mounting bracket as seen in Figure 1 Tighten the thread cutting bolt enough to mark the front leg socket for drilling 1h Disassemble the
3. TIE DOWN product replace the TIE DOWN product or repair the product TIE DOWN has sole discretion in choosing which option to provide For this LIMITED WARRANTY to apply TIE DOWN must receive notice of the alleged defect within 30 days of either the discovery of the alleged defect or the expiration of the warranty period whichever is earlier Any claim not made within this period shall conclusively be deemed waived If requested by TIE DOWN purchaser shall return the alleged defective product to TIE DOWN for examination at purchasers expense TIE DOWN will not pay for expenses incurred in returning a product to TIE DOWN without TIE DOWN s prior written authority TIE DOWN shall not be liable for any other expenses purchaser incurs to remedy any defect Purchasers waive subrogation on all claims under any insurance Limitation of Liability It is expressly agreed that the liability of TIE DOWN is limited and TIE DOWN does not function as an insurer THE REMEDIES SET FORTH IN THIS WARRANTY SHALL CONSTITUTE THE EXCLUSIVE REMEDIES AVAILABLE TO THE PURCHASER OR USER AND ARE IN LIEU OF ALL OTHER REMEDIES EXPRESS OR IMPLIED THE LIABILITY OF TIE DOWN WHETHER IN CONTRACT IN TORT UNDER ANY WARRANTY OR OTHERWISE SHALL NOT EXCEED THE PURCHASE PRICE OF THE PARTICULAR PRODUCT MANUFACTURED SOLD OR SUPPLIED BY TIE DOWN To Obtain Technical Assistance To enable TIE DOWN to respond to a request for assistance or evaluation of customer or user operating difficulty
4. four 5 16 18 X 1 1 4 hex head bolts four 5 16 lock washers and four 5 16 flat washers and install as seen in Figure 4 Tighten all fasteners at this time on the rear mounting bracket Take a 3 8 16 X 1 thread cutting bolt and install into the rear mounting bracket as seen in Figure 4 Tighten the thread cutting bolt enough to mark the front leg socket for drilling Disassemble the rear leg socket assembly taking the rear leg socket and drill a 7 32 pilot hole through the mark created in the previous step with the thread cutting bolt Then re drill the hole using a 1 2 drill bit Reassemble the rear leg socket assembly to the truck bed tightening all hardware except the 3 8 16 x 1 thread cutting blot Now proceed to step 3 Figure 4 ear leaGorret Assembly Note ee ey ts if the best mounting hole 2 location is between floor ribs a floor spacer and or two extra 5 16 flat washers have been provided to fill the void Rotate the leg shocket 90 degrees to the Rear Mounting rear of the vehicle if possible Plate 1 Plate 2 not used Coe 5 16 1 amp x 1 1 4 Hex Head Bolt i KA 4 locations pa lt 5 16 Lock Washer _ 4 locations V N ne Flat Washer 4 locations STEP 3 INSTALLING THE FRONT UPRIGHT 3a Take one upright and insert into the front leg socket assembly Tighten the 3 8 16 x 1 thread cutting screw installed in step 1f in the front mounting bracket 3b Take one ext
5. limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state No representative has authority to make any representation promise or agreement except as stated in this Limited Warranty TIE DOWN reserves the right to make design and other changes upon its products without any obligation to install the same on any previously sold or delivered products DUE TO THE WIDE VARIATION IN USES TO WHICH TIE DOWN PRODUCTS WHEELS HUBS BRAKES ETC ARE SUBJECTED BY USERS WE ARE UNABLE TO SPECIFY CARRYING CAPACITIES OR SPEEDS FOR A PARTICULAR APPLICATION THEREFORE THE MANUFACTURER MUST TEST HIS EQUIPMENT UNDER THE MOST SEVERE CONDITIONS TO DETERMINE THAT TIE DOWN PRODUCTS ARE SUITABLE THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THOSE DESCRIBED ABOVE EFFECTIVE JANUARY 2003 THIS WARRANTY SUPERSEDES ALL PRIOR WARRANTIES WRITTEN OR IMPLIED TIE DOWN ENGINEERING 255 Villanova Drive SW Atlanta GA 30336 ar j www tiedown com 404 344 0000 Fax 404 349 0401 DOWN ENGINEERING 1021135 E1346
6. ENGINEERING Installation Manual Roof Zone Ladder Rack Installation Time Tools Required About 90 minutes Electric Drill with 1 2 Chuck Depending on truck 1 2 amp 7 32 Drill Bits and Do it Yourself 1 2 9 16 amp 3 8 Open or Box End Wrenches experience level screwdriver Framing Square Level Center Punch Hack Saw Tape Measure 102113 E1346 TIE DOWN ENGINEERING 255 Villanova Drive SW Atlanta GA 30336 r www tiedown com 404 344 0000 Fax 404 349 0401 ENGINEERING WARNING Before drilling insure that there are no fuel lines fuel tanks brake lines electric wires etc this may require checking under the vehicle for all drill locations Wear protective eye wear when checking the underside of the vehicle or when drilling This product is only intended for transporting ladders lumber pipe and other similar materials It is the responsibility of the user of this truck rack to secure materials to the rack before transporting Any modifications made to this product for any other purpose than its intended use could create a hazardous condition that can cause serious personal injury or property damage To prevent damage from vibration during vehicle operation with an unloaded rack leg assemblies should be removed Any modification or unintended use of this product shall immediately void all manufacturers warranties Manufacturer disclaims all liability for injuries to persons or property r
7. ained see Figure 7 Remove and cut the uprights if desired Note that you need to cut from the bottom of the upright Double check the measurement before cutting 5b Secure ladder with the provided ladder straps when transporting Secure or remove ladder straps when not being used Secure ladder with Figure 7 Velcro Ladder Strap j 2 Min EAD S yH aa CE STEP 6 INSTALLATION OF ROPE CLEATS optional The two rope cleats are to be mounted where desired Apply silicone sealant around all drilled metal holes See right for installation procedure FIGURE 9 RIVNUT FASTENER INSTALLATION Note Make sure there is enough hole depth before installing the Rivnut fastener Note Black Oxide Bolt Flat Washer and Installation Tool are only used to install Rivnut fastener Place a drop of oil on the black oxide bolt for lubrication Insert Rivnut fastener in the hole Hold the Installation Tool with a 9 16 wrench while turning the Black Oxide Bolt with a 1 2 wrench until fully seated Make sure the rivnut fastener and installation tool do not turn while tightening Turning Black Oxide Bolt will be hard until fastener bulbs out When Rivnut fastener is fully seated remove the black oxide bolt and washer and continue with the installation 10 24 Flat Washer 2 y Figure amp eZ Cleat Apply sealant around holes before assembl
8. e Hex Head 5 16 18 X 1 bolts washers and nylon lock nuts fasten the rear mounting bracket plate 1 and 2 together The long end of the angle on plate 2 faces away from plate 1 Insert the rear leg socket into the rear mounting bracket assembly as seen in 3 Hold the mounting bracket assembly flush with the tailgate stop ensuring that the rear leg is plumb and square to the truck bed See note at bottom of page for mounting to truck bed floor Mark the five holes Remove the assembly and center punch each of the holes Drill a 7 32 pilot hole then re drill each hole using a 1 2 drill bit Apply silicone sealant around all drilled metal holes Install rivnut fastener into each drilled hole see page 7 Figure 9 for rivnut fastener installation instructions Take the rear leg socket assembly four 5 16 18 X 1 1 4 hex head bolts four 5 16 lock washers and four 5 16 flat washers and install as seen in Figure 3 It may be necessary to dis assemble rear mounting bracket plate 1 and 2 in order to fasten plate 2 to the truck Tighten all fasteners at this time on the rear mounting bracket Take a 3 8 16 X 1 thread cutting bolt and install into the rear mounting bracket as seen in Figure 3 Disassemble the rear leg socket assembly taking the rear leg socket and drill a 7 32 pilot hole through the mark created in the previous step with the thread cutting bolt Then re drill the hole using a 1 2 drill bit Reassemble the rear leg soc
9. ension and insert it into the upright as seen in Figure 6 After tighten at the desired location seal the joint between the two tubes Figure 6 3 8 16 x 3 3 4 Carriage Bolt on the extension 3 8 16x3 4 Thread N P Cutting Screw Locks the extension Install the Ladder Stop with the provided silicone sealant 3c Take the ladder stop one 3 8 16 x 3 4 carriage bolt one 3 8 flat washer and one 3 8 16 nylon lock nut and install onto the upright as seen in Figure 6 3d Take the one strap and install it onto the bracket as seen in Figure 6 STEP 4 INSTALLING THE REAR UPRIGHT to the leg s a Adjust extension to prevent side motion of the ladder 3 8 Flat Washer 3 8 16 Nylon Lock Nut 4a Take the remaining upright and insert into the rear leg socket assembly Tighten the 3 8 16 x 1 thread cutting screw installed in step 2f in the rear mounting bracket 4b Take the remaining extension and insert it into the upright as seen in Figure 6 After tighten at the desired location seal the joint between the two tubes with the provided silicone sealant 4c Take the remaining ladder strap and install it onto the bracket as seen in Figure 6 STEP 5 SECURING A LADDER TO THE RACK 5a Carefully place a ladder on the rack and check door entry and head clearance If clearance is ample and if desired the uprights may be shortened as long as a minimum of 2 above the cab roof is maint
10. esulting from any modification to or unintended use of this product The manual shows installation on the passenger side of the vehicle For installation on the driver side simply reverse the parts If your pickup has a bed liner you may be required to drill trim or cut the liner for installation of this product The best mounting location is between floor ribs a spacer and or two extra washers have been provided to fill the void Or rotate the leg socket assembly 90 degrees to the rear of the vehicle if possible If you are installing this product on a F 150 the F 150 adapter provided must be used If at any time during the assembly or installation procedures you have a question or are in need of assistance call 1 800 241 1806 Apply silicone sealant around all drilled metal holes Warranty will be void if sealant is not properly applied to all seams and crevices in the truck bed Do not seal uprights to the leg socket Its strongly recommended that you remove and store the upright assemblies when they are not in use STEP 1 MOUNTING THE FRONT LEG SOCKET NEAR CAB 1a If installing on a 2004 Ford F 150 and newer place the F 150 Adaptor onto the front leg socket Install and tighten a 3 8 16 x 1 thread cutting bolt into the adaptor to make a mark on the front leg socket Remove adapter and drill a 7 16 pilot hole and then a 1 2 hole at the indention mark of the thread cutting bolt on the leg socket Re install the F
11. front leg socket assembly take the front leg socket and drill a pilot hole with a 7 32 drill bit through the mark created in the previous step by the thread cutting bolt Then re drill the hole with a 1 2 drill bit Apply silicone sealant around all drilled metal holes Reassemble the front leg socket assembly to the truck bed tightening all hardware except the 3 8 16 x 1 thread cutting blot Figure 1 Square the assembly e Mark Mounting bracket holes to the bed e Center punch marks Ford F 150 Adaptor not shown Drill 7 32 pilot hole 3 8 16x1 thread cutting screw o Re drill with 1 2 drill bit ss Tighten the screw enough to 4 locations lt a mark the tube for drilling we Install Rivnut Fastener F Br f 4 locations See last ront 2 Lee page for instructions of Bed L A 5 16 18 x 1 1 4 Hex Head i 4 locations i 5 16 Lock Washer 7 amp 4 locations 5 16 Flat Washer EZ 4 locations Mark the front Leg Socket hole that aligns best on the top of a floor rib Drill 7 32 pilot hole then re drill with 1 2 drill bit where the screw market the tube Figure 2 Ford 150 Adaptor 3 Step 2 MOUNTING THE REAR LEG SOCKET Step 2a g is to be used when mounting to a 90 degree tailgate stop Most vehicles NOTE Skip to Step 2h if you own a Toyota Tacoma Chevy Colorado or GMC Canyon with a 45 degree tail gate stop 2a 2b 2C 2d 2d 2f 20 Using th
12. ing me n 10 24 x 2 Machine Screw 2 10 24 Nylon Lock Nut 2 Figure 9 Black Oxide Bolt e Flat Washer SS 9 16 Wrench O Installation Tool ___ l m Rivnut Fastener gt i TIE DOWN ENGINEERING GENERAL PRODUCT LINE LIMITED WARRANTY Limited Warranty TIE DOWN ENGINEERING Inc TIE DOWN warrants its products to be free from defects in material and workmanship for one year from date of delivery to the original purchaser when properly installed used and maintained by the purchaser This warranty does not apply to damage or loss caused by any or all of the following circumstances or conditions e Damage caused during installation e Parts accessories materials or components used with or replacing any TIE DOWN braking system not obtained from or approved in writing by TIE DOWN e Misapplication misuse and failure to follow the directions or observe cautions and warnings on installation operation application inspection or maintenance specified in any TIE DOWN quotation acknowledgement sales literature specification sheet or installation instruction and service manual applicable literature e Use of product in any other application other than those described in TIE DOWN s product information materials If any TIE DOWN products are found upon TIE DOWN s examination to have been defective when supplied TIE DOWN will either credit the purchaser s account for the purchase price of the
13. ket assembly to the truck bed tightening all hardware except the 3 8 16 x 1 thread cutting blot Now proceed to step 3 Figure 3 Assembly Note if the best mounting hole location is between floor 7 ribs a floor spacer and or two extra 5 16 flat washers have been provided Plate 2 to fill the void Rotate the leg shocket 90 degrees to the rear of the vehicle if possible LD Rear Leg Socket Long End of Angle of Plate 2 Rear Mounting Bracket Plate 1 A I y 0 516 18 x 1 1 4 EF S y G Hex Head Bolt p w 4 locations i lt 5 16 Lock Washer lt _ 4 locations gt Flat Washer 4 locations Mark the Front Leg Socket hole that aligns best on the top of a floor rib Start here for 45 degree tailgate stop 2h 2C 2d 2e 2f 20 Insert the rear leg socket into the rear mounting bracket plate 1 as seen in 4 Plate 2 will not be used Hold the mounting bracket assembly flush with the tailgate stop ensuring that the rear leg is plumb and square to the truck bed See note at bottom of page for mounting to truck bed floor Mark the five holes Remove the assembly and center punch each of the holes Drill a 7 32 pilot hole then re drill each hole using a 1 2 drill bit Apply silicone sealant around all drilled metal holes Install rivnut fastener into each drilled hole see page 7 Figure 9 for rivnut fastener installation instructions Take the rear leg socket assembly
Download Pdf Manuals
Related Search