HD7826/10 /11 /18 - Senseo onderdelen
Contents
1. 41920 Distribution disk 16 4222 259 50632 PCB assy Green LED ECO 17 4213 247 05250 Foot 18 4222 259 50641 3 Way valve Viva Caf PP 19 4222 259 52091 Boiler assy V7 0 230 V Green 20 4222 247 06591 Hose 21 4222 247 05130 O ring NTC 22 4222 259 47301 NTC assy 23 4222 259 37240 Pump 230 V 50 Hz 24 4222 247 63141 Valve outlet Deep Black 25 4222 259 46071 Back Cover assy Deep Black 26 4222 247 05510 Corrugated tube 5 8 EXPLODED VIEW HD7826 10 II 18 6 8 HD7826 10 II 18 EXPLODED VIEW 7 8 HD7826 10 II 18 A 5 EXPLODED VIEW 0 U 8 82. Service Service Service Philips Consumer Lifestyle PRODUCT INFORMATION This product meets the requirements regarding interference suppression on radio and TV After the product has been repaired it should function properly and has to meet the safety requirements as officially laid down at this moment TECHNICAL INFORMATION Voltage Frequency Power consumption Standby power consumption Stand by time auto shut off Contents water reservoir Colour setting Sap coding Published by Philips Consumer Lifestyle 11 06 Coffee maker Senseo Viva Cafe HD7826 10 HD7826 1 I HD7826 18 Interconnect Brewhead Water level sensor L 220 240 V AE AS Control 1450W PCB 0 4 W 5 min 1200 cc N Fusion White HD7826 10 Push buttons Printed in the Netherlands Copyright reserved Subject to modification PHILIPS DISASSEMBLY AND RE ASSEMBLY ADVISE Before you start dismantling For your safety be sure the plug is disconnected from the mains The product is designed for easy access to the internal components Make sure that all accessories like tank podholder drip tray spout and collector have been removed To remove the back cover follow below steps Remove the two Torx screws T15 A see exploded view Remove the valve outlet Start at the upper side of the back cover using a flat head screwdriver to unhook the top of the back cover and gentl
3. p button pump time will be shorten with 0 5 sec is approximately 3 5 cc mL less coffee Pushing 2 cup button pump time will be lengthen with 0 5 sec is approximately 3 5 cc mL more coffee When the volume has to increase with 10 cc for example push the 2 cup button 3 times The new value will be stored when you switch the appliance off by pushing the main switch LED will turn off 11 Turn appliance on again and brew one cup measure the volume In case the volume is not within specification repeat steps 6 11 12 End 3 8 REPAIR INSTRUCTION Filling procedure Please note the software of the Senseo Viva Caf has changed compared to predecessor Senseos The filling procedure known from predecessor Senseo s is no longer available The command originally used to initiate the filling procedure cold flush pushing both the 1 cup and 2 cup buttons simultaneously will now start the decalcification process To perform a cold flush of the appliance it has to be reset to factory default See topic Restoring the Boiler_empty_flag to factory default below As a back up when the appliance is in factory default setting the cold flush will also be initiated when the user presses either the 1 cup or the 2 cup button This functionality is only available after restoring the Boiler_empty_flag to factory default Restoring the Boiler_empty_flag to factory default Under some circumstances it might be necessar
4. ume adjustment The PCB circuit board makes it possible to adjust the volume output by means of pushing the one cup and two cup user controls How to adjust the volume output 1 Make sure the boiler is filled properly otherwise perform fill procedure see DFU for instructions 2 Switch appliance on and wait until the unit is ready to brew 3 Make sure a pod holder is placed but without a Coffee POD Only adjusting with plain water 4 Place a cup on the drip tray cover and push the one cup button 5 When the appliance has finished it is stabilized to perform the volume adjustment 6 Empty the cup podholder and push again for one cup setting measure the volume output with a graduated beaker In the table you can find the requirements for the minimum maximum volume output cc mL values depending from the country version One cup setting Including Pod holder water spec Without Coffee pod po Min water cc mL Max water cc mL 7 Unplug the appliance from the mains 8 Press the 1 and 2 cup button simultaneously and plug the mains on 9 When above step succeeded the LED will turn on continuously 10 Depending if the volume has to de or increase you have to push the one or two cup button Every time you push the 1 or 2 cup button the LED will turn off for 0 5 second feedback to user and the pump time will be shortened or lengthened for 0 5 seconds depending which button was pushed Pushing 1 cu
5. uted When the restore to factory default procedure is not carried out a new and empty boiler can be switched on without having the protection of the initial flush procedure causing the thermal fuses in the heating element to fail A After a boiler replacement or drained system carry out the Restore boiler_empty_flag to factory default procedure Then the initial flush procedure can be carried out Descaling Descaling is an important element in Senseo maintenance It should be done at least once every 3 months up to 6 times a Year This will prolong the life of your appliance and will guarantee optimal brewing results for a long time Use the correct descaling agent Only citric acid based descalers are suitable for descaling the SENSEO machine This type of descaler descales the appliance without damaging it For the correct amount see under Descaling procedure below Each descaling mixture can be used only once After use the descaling mixture is no longer active We advise you to use the special SENSEO Descaler HD7006 Read the instructions on the package of the descaling agent Never use a descaling agent based on mineral acids such as sulphuric acid hydrochloric acid sulphamic acid and acetic acid e g vinegar These descaling agents may damage your SENSEO coffee machine Follow the steps in the section headed Descale the appliance see DFU Direction for Use manual HD7826 10 II 18 Vol
6. w chamber head assy follow below steps Remove the back cover Place the appliance in front of you in such a way that you are facing the rear side of the appliance First remove the boiler from the snap lock position of the brew chamber To remove the brew chamber use your both thumbs see picture 3 and push strongly with a little distortion rotation until the brew chamber comes loose upwards picture 3 Reassemble follow above steps backwards To reach the components placed inside the base for example exchange the NTC temperature sensor follow below steps First remove back cover three way valve and boiler The brew chamber can be removed by unhooking the two snap locks behind the boiler pull the brew chamber upwards to remove it from the housing Remove both Torx T15 screws B see exploded view Unhook the two snap locks on the back side of the base with a screwdriver see base the housing can now be removed To remove the rest of the housing unlock the last 4 snap locks on the base and gently pull of the front cover To reassemble follow above steps backwards OPTIONAL accessories No specific issues 2 8 REPAIR INSTRUCTION Note Please note after replacing the boiler the appliance has to be restored to factory default The filling procedure cold flush known from the predecessor Senseo s is no longer available after the flush before first use has been exec
7. y pull the back cover from the appliance so that a little chink between back cover and brew chamber becomes visible Again use the screwdriver to unhook the two snap locks at each side of the back cover and gently move the screwdriver in the direction of the opposite side of the appliance in such a way that the lips of the snap locks are bent outwards and unhook If all snap locks are unhooked it is possible to remove the back cover Gently pull the back cover upwards to release the bottom part of the back cover from the housing Please note that the back cover is still connected to the pump For reassembly follow these steps backwards To remove the brew chamber lid cover follow below steps Place a large screwdriver on the positions see picture 1 and lift the cover over the snap locks on both positions use appropriate force The cover lid can now be lifted up but stays attached to the brew head by the push rod to remove the complete cover including lever and push rod squeeze both legs of the push rod strongly together see picture 2 so that the two pins will unhook out of the picture 2 hinge position on the brew chamber To remove lever from lid cover take a screwdriver and bend carefully the two lips ribs in the lid cover outwards and push the lever with force out of the hinge To reassemble follow steps backwards without using a screwdriver HD7826 10 II 18 To remove the bre
8. y that the boiler of the Senseo is emptied This for instance during wintertime were the possibility exists that the boiler becomes frozen during transport For those occasions it is useful to restore the Boiler_empty_ flag to production default Bringing the Senseo back into production status has the benefit that the flush routine will be activated automatically when installed by the consumer see topic Automatic filling procedure To SET the Boiler_empty_flag Keep the 1 cup button pressed while plugging in the power cord of the appliance The main switch LED will blink very rapidly for approximately 1 second To check if the Boiler_empty_flag is really set you should reconnect the power cord a second time to the net and push the main switch The main switch LED should light continuously HD7826 10 II 18 4 8 PARTS LIST HD7826 10 II 18 Pos Service code Description Remark l 4222 259 44210 Padholder assy 1 cup Deep Black 2 4222 259 44220 Padholder assy 2 cup Deep Black 3 4222 247 42550 Collector 4 4222 259 50862 Spout cover Matt Metal 5 4222 259 48241 Spout assy Black 6 4222 240 00021 Driptray cover 7 4222 247 66111 Driptray Black ECO 8 4222 259 46111 Water container assy Silent Blue 9 4222 247 66131 Lever Fusion Black ECO 10 4222 247 63071 Pushrod 11 422224001410 Slider Spring I UUU LD D Brew chamber assy Fusion Black 13 4222 247 06810 Brew chamber seal 14 4222 240 05990 Ejector pin 15 4222 247
Download Pdf Manuals
Related Search