2010 INDIAN MOTORCYCLE PRE- DELIVERY
Contents
1. Inspect for leaks Comments Brake Fluid Check master cylinders level and adjust as required Comments Front Brake Lever Check operation and return position Comments Rear Brake Pedal Check operation position and adjust as required Comments Engine Oil Check level and adjust as required Comments Oil Filter Check for leaks Comments Oil Lines Inspect for leaks Comments Transmission Oil Check level and adjust as required Comments Clutch Fluid Check master cylinder level and adjust as required Comments Clutch Check operation and return position Comments Clutch Lines Insect for leaks Comments Throttle Check Control Grip return and inspect control cable s for smooth operation Comments Engine Idle Speed Confirm idle speed and record Comments Fuel Lines and Fittings Inspect for leaks Comments Check for Failure Codes Check for OBD codes and record Comments Exhaust System Check for leaks Comments Evaporative Emission Control System CA only Inspect Hose Condition and routing Comments Doc 80700000 Battery Charge check mounting system and charging system output Comments Electrical Components Check operation of headlight tail light turn signal2. VOID Indicates information that will affect the validity of one or more of your IMC Warranties We recommend you pay special attention to these notices and observe all warnings and cautions Doc 80700000 Ji Preparing the Motorcycle Sadian EST 1901 6 SERVICE Windshield The windshield comes in a separate box that is shipped to your dealership This feature comes standard on RoadMaster and Vintage models or can be added to Standard or Deluxe models Your windshield uses a key lock to ensure the windshield is properly locked into place and to prevent theft To install the windshield unlock windshield lock located on right side of motorcycle at approximately handlebar height The key is tapped to the windshield Locate lower mounts and Line up upper mounts Install windshield to motorcycle by pushing forward and down Lock windshield lock and remove key Battery Connection 1 Connect positive cable plus battery tender lead to positive battery post 2 Connect 2 negative cables plus battery tender lead to negative battery post 3 Torque both battery fasteners to 50 96 inch pounds Seat Installation 1 Place the seat tongue under the frame mount 2 For models with a passenger seat align the passenger seat mount to the fender hole Place the 1 4 20 button head bolt with lock washer and flat washer through the seat bracket Slip the nylon washer between the fender and bracket Align the bolt to the fender hole and thread inw
3. 2010 INDIAN MOTORCYCLE PRE DELIVERY AND INSPECTION NO TORCYCLE am EST 1761 SERVICE Doc 80700000 ea Table of Contents MOTORCYCLE SERVICE Introduction Preparing the motorcycle Pre Delivery Checklist Customer Acceptance Doc 80700000 gt Introduction Sndian EST 1901 6 SERVICE For your own safety and longer service life of your motorcycle follow the instructions and warnings contained in this manual Ignoring them could result in damage to the motorcycle or personal injury to yourself or others Damage to your motorcycle caused by failing to follow these instructions is not covered by the Indian Motorcycle Company Limited Warranty At Indian Motorcycle Company we continuously strive for improvements in product design quality and performance Please understand that as a result of our ongoing improvement efforts we reserve the right to make changes in the design and manufacture of the motorcycle Therefore the information illustrations and descriptions in this manual might differ from your motorcycle Statements in this manual preceded by the following words are of special significance A WARNING Indicates the possibility of personal injury to yourself or others if instructions are not followed CAUTION Indicates the possibility of damage to the vehicle if instructions are not followed Note Indicates other information of particular importance placed in italic type
4. ard Do not tighten 3 Align the seat side brackets to the frame holes Slip the 5 16 18 button head bolts through the brackets and into the frame Torque to 95 115 inch pounds 11 13 Nm Mirror Installation 1 Mirrors are shipped in separate box that comes with the motorcycle 2 Install mirrors and adjust for proper viewing 3 Torque to 14 16 Ft Ibs Doc 80700000 Cleaning the Motorcycle AWARNING When washing your motorcycle do not use power washers Power washers allow water to prematurely corrode bearings and bearing surface areas If you choose to use power washers you will have to check clean repack or replace bearings on your motorcycle more often then scheduled maintenance intervals AWARNING Many cleaning products can be hazardous Some are poisonous and or flammable Carefully observe warnings and cautions provided on the labels of cleaning compounds to prevent personal injury or damage to your motorcycle Never use fluids or solvents that are not designed for cleaning your motorcycle AWARNING Never wash the brake discs on your motorcycle with any cleaners that contain either chlorine or silicon Chlorine will cause the brake discs to rust Silicon will make the brake discs slick which will adversely affect braking ability and which may result in personal injury and damage to the motorcycle CAUTION When washing your motorcycle be careful not to allow too much water to come into contact with the brakes engine muff
5. elivery according to all applicable Pre Delivery and Set Up Instructions Delivering Dealer s Service Technician Signature Date Torque Wrench Calibration Date Doc 80700000 Saien H Customer MOTORCYCLE enred Acceptance SERVICE CUSTOMER S ACCEPTANCE have inspected the motorcycle and find the motorcycle acceptable as per the sales agreement All equipment is functioning and understand the operation of the motorcycle and its equipment per the owner s manual and the dealer s explanation have received a copy of the Indian Motorcycle Limited Warranty during the purchase of this motorcycle and understand my rights under this limited warranty program THIS DOCUMENT IS NOT A WARRANTY BUYER ACKNOWLEDGES THAT THERE ARE NO ORAL REPRESENTATIONS OR WARRANTIES MADE OTHER THAN THOSE REFLECTED IN THE INDIAN MOTORCYCLE LIMITED WARRANTY CUSTOMER signature CUSTOMER PHONE NUMBER CUSTOMER ADDRESS DEALER S EXPLANATION have explained to the customer and instructed the customer in regards to preparing the motorcycle operation of the motorcycle and its equipment owner s maintenance and have provided to the customer a copy of the Indian Motorcycle Limited Warranty DEALER Doc 80700000
6. lers or air filter Wet brake pads or a wet brake disc will adversely affect braking ability Never use a pressure washer to clean your motorcycle Ensure the engine and the brakes are in proper operating condition prior to riding your motorcycle Leather Care Leather must be cleaned and treated to properly maintain its quality appearance and extended life Clean and treat leather more often under adverse conditions CAUTION Only use proper leather cleaners and conditions to treat your Indian Motorcycle leather e Do not clean with ordinary soap or cleaners e Use high quality saddle soap or leather cleaner e Use Indian Leather Care to treat your leather Battery Maintenance Indian Motorcycle strongly recommends that deliberate steps are taken to properly maintain the battery while the motorcycle is on the show room floor The battery in the motorcycle should be charged using a battery tender or similar every 30 days of non use for proper maintenance The motorcycles are shipped with a battery tender lead 3 amp max located on the upper edge of the right center fairing Another suggestion would be to remove the battery from the vehicle after the PDI has been completed The battery can be put on a battery tender or similar type charger to maintain proper charge Doc 80700000 PRE DELIVERY CHECKLIST This check list is NOT a warranty This checklist must be completed prior to Sadan MOTORCYCLE re EST 1901 Oo delivery of the motorc
7. s brake light hazard 4 way flashers indicator lights horn speedometer light engine starter switch and engine stop switch and instrument mode switch Comments Electrical Accessory Plug s Check for proper operation Comments Headlamp Adjust horizontally and vertically according to laws in your state Comments Kickstand Check under weight of motorcycle and check return action Comments Fenders Check mounting bolts for proper torque Comments Seat Check mounting bolts for proper torque Comments Windshield If equipped Tighten windshield fasteners to 3 5 inch Ibs and install on bike Road Test Check motorcycle for abnormal noise handling and operation of speedometer brakes clutch engine and transmission operation Comments Clean Polish and Detail Motorcycle Comments Delivery Explain operation of all controls and break in procedure Comments Delivery Adjust all controls and handlebars to customer s preference Comments Owner s Manual Explain contents provide information on rider safety training programs and instruct rider and passenger to wear proper motorcycle safety gear at all times Comments Additional Comments Delivering Dealer s Service Technician certify that have inspected this vehicle and that it has been prepared for d
8. ycle to the customer The items on the checklist must be tested and or reviewed in accordance with Indian Motorcycle approved methods and procedures using S F R y C E specialized tools and equipment See Service Manual After each item has been inspected and found to be in proper order place a checkmark next to that item After the motorcycle has been thoroughly check and road tested the delivering dealer and test rider must sign and date the form Upon delivery of the motorcycle the customer should also sign and date the form OK Adjustment Required Paint Check Condition Comments Chrome Check Condition Comments Tires Adjust to correct pressure Comments Front Axle Check nuts for proper torque See Service Manual Comments Steering Head Bearings Check for smooth movement and play See Service Manual Comments Rear Shock Absorber Adjust for rider weight and secure Comments Rear Pulley Check fasteners for proper torque Comments Rear Drive Belt Sonic Check and adjust as required Comments Record Belt Readings in three locations 1 2 3 Primary Chain Post Ride Check Check tension and fluid level and adjust as required Comments Brake Rotors Check fasteners for proper torque Comments Brake Calipers Check mounting fasteners for proper torque Comments Brake Lines
Download Pdf Manuals
Related Search