TWIN CAM CRANKCASE BORING TOOL - Harley
Contents
1. 1 4 inch screws 11 and one 5 16 inch screw 14 with SAE 20w50 Harley Davidson motorcycle oil If the front cylinder is being bored install the screws in the left mounting plate holes marked F If the rear cylinder is being bored install the screws in the mounting plate holes marked R This will align the cylinder spigot bore perpendicular to the base Do not tighten at this time See Figure 2 Install T pin Figure 10 Item 15 into the alignment plate in the hole locations shown If the front cylinder is being bored install the T pin in the alignment plate hole marked F If the rear cylinder is being bored install the T pin in the alignment plate hole marked R It may be necessary to rotate the engine case slightly in order to install the T pin Tighten screws 11 to 90 120 in Ibs 10 13 Nm Tighten screws 14 to 156 180 in lbs 18 20 Nm J04198 is03462 Figure 2 Engine Crankcase in Engine Cradle Ea Pisooses Figure 3 Install T pin into Engine Crankcase and Engine Cradle NOTE Failure to check the cylinder dowel clearance may result in the final spigot bore being out of center 14 See Figure 10 Cylinder dowel height may vary verify that there is sufficient clearance between the machined reliefs 2of9 of the boring head assembly locating plate 5 and the cylinder dowels of the neighboring cylinder as follows a Place the boring head assembly on the engine crankc2. even pressure until the boring assembly stop bottoms out b Shut down the drill or milling machine and wait until the boring head comes to a complete stop c Slowly and carefully retract the boring head from the engine crankcase 10 See Figure 7 Replace the block of wood between boring head assembly plates to prevent the boring head from contacting the engine crankcase 11 Remove two socket head cap screws and the boring head assembly from the engine crankcase NOTE If the application requires that the final bore cut be taken in two passes repeat Steps 7 11 with the boring head assembly setup for the second pass bore cut adjusted for dimensional runout see note at the beginning of this section 12 See Figure 10 Remove two 1 4 20 inch socket head cap screws 11 T pin 15 and three 5 16 18 inch socket head cap screws 14 or two 1 4 20 inch screws 11 and one 5 16 inch screw 14 depending on application then rotate the engine crankcase so that the opposite engine crank case spigot bore is straight up 13 Reinstall the hardware removed in the previous step according to the instructions given in the Steps 9 13 of the ENGINE AND TOOL PREPARATION section of this Instruction Sheet 14 See Step 5 in this section and reinstall the boring head assembly to the engine crankcase 15 Repeat Steps 7 11 of this section for the opposite cyl inder J04198 NOTES When boring the O ring counterbore move the bor
3. more than 0 125 in 3 175 mm of the diameter be removed in one pass The engine crankcase machining may require more than one pass and more than one boring head set up to obtain the final bore Attempting to remove more than the recommended amount of material in one pass may result in a rough finish and or damage to the bore and tool bits If the tool bits are set for a bore larger than 4 45 in 113 03 mm the tool bits will contact and cause damage to the inner diameter of the locating plate Figure 10 Item 5 and or tool bits Figure 10 Item 16 1 See Figure 4 Install the cutting bits into the bore head and set boring diameter as follows a Using a 1 8 inch hex key wrench thread six set screws into the cutting head Do not thread them into the holes far enough to prevent the cutting bits from being inserted into the bore head b Install the tool bits into the bore head oriented as shown c See Figure 6 See the Instruction Sheet for the cyl inder kit being installed to determine final spigot bore diameter Subtract the stock spigot bore diameter 5 from the final spigot bore diameter 4 to determine the diameter difference Divide by two to determine radius difference 3 If the radius difference is 0 0625 in 1 5875 mm or less divide it by 2 this is the setback of the rough cut tool bit from the finish cut tool bit The finish tool bit protrusion is the finish spigot bore radius less the boring head radius The
4. rough tool bit protrusion is the finish spigot bore radius less 1 2 the radius difference 3 less the boring head radius If the radius difference is 0 0625 in 1 5875 mm or more the bore cut will require two passes The first pass should be 1 2 of the total cut 3 of 9 The finish tool bit protrusion for the first pass is the finish spigot bore radius less 1 2 the radius difference less the boring head radius The rough tool bit protru sion for the first pass is the finish spigot bore radius less 1 2 the radius difference less 1 4 the radius dif ference less the boring head radius The finish tool bit protrusion for the second pass is the finish spigot bore radius less the boring head radius The rough tool bit protrusion for the second pass is the finish spigot bore radius less 1 4 the radius difference less the boring head radius d See Figure 4 Set the rough cut 4 and finish cut 5 tool bit depths using the set screws 3 Use an appropriate measuring tool to ensure accurate measurements e While ensuring that the tool bits are pressed tight to the depth set screws 3 tighten the locking set screws 1 then locking set screws 2 Tighten locking set screws to 90 in Ibs 10 Nm is03606 Finish cut radius Stock bore radius Depth of finish cut radius difference Finish cut diameter Stock bore diameter RON Figure 6 Calculate Tool Bit Settings 2 Set the bore depth as follows a S
5. the bore head for the second pass the finish tool bit setting would be reduced by 0 002 in e g if the final bore diameter is intended to be 4 415 in then adjust finish tool bit protru sion 0 482 in for dimensional runout 0 002 in over size by subtracting 0 002 in from the second pass finish tool bit protrusion 0 482 in 0 002 in 0 480 in 1 Place the engine crankcase cradle without the boring head assembly installed onto a drill press or milling machine table NOTE Assemble a dial indicator into the drill press chuck or milling machine collet and sweep the cutting surface of the engine crankcase to ensure that the cutting surface is perpendicular to the spindle of the drill press or milling machine If it is not shim between the crankcase cradle assembly and the drill press or milling machine table Adjust as necessary until the cutting surface is perpendicular to the spindle 2 Check and ensure cutting surface is perpendicular to spindle of drill press or milling machine 3 See Figure 7 Place a block of wood between boring head assembly plates to prevent the boring head from contacting the engine crankcase 4 See Figure 10 Lubricate two screws 10 with SAE 20w50 Harley Davidson motorcycle oil Install the boring head assembly onto the engine crankcase with two lubricated socket head cap screws Ensure that the boring head assembly locates properly on the cylinder dowels and sits flush on the engine cr
6. ace 21 Using a 5 16 18 inch bottoming tap tap the screw hole to a minimum depth of 1 59 in 40 39 mm from the gasket surface 22 See Figure 1 and Figure 9 Remove the thin material between the cylinders next to the top center screw as shown by using a 5 8 inch ball end mill and milling a 5 16 in radius at the two points shown 23 Refer to the appropriate Service Manual and assemble the engine with the following changes a Tighten all of the engine crankcase screws to the specified torque except the top center engine crankcase screw b After the cylinders and heads have been installed and the hardware tightened to specification install the top center engine crankcase screw provided in the Harley Davidson 110 Inch kit or Screamin Eagle Pro Bigger Bore Cylinder kit Part Number 1090 Tighten the screw to 50 90 in Ibs 5 6 10 2 Nm 6 of 9 is03502 val oy E 1 Tap hole with a 5 16 18 UNC 2B bottoming tap 6 Extend hole depth 1 00 in 25 4 mm maximum 2 Extended full thread depth 0 80 in 20 32 mm 7 Unthreaded hole depth 0 79 in 20 07 mm 3 Distance 0 48 in 12 19 mm 8 Distance to center of crank 5 90 in 149 86 mm 4 Distance 0 48 in 12 19 mm 9 Distance to center of crank 6 00 in 152 40 mm 5 Drilled hole diameter 0 34 in 8 64 mm 10 Radius 0 31 in 7 87 mm Use 5 8 in ball end mill Figure 9 Top Center En
7. ankcase Tighten the cap screws to 18 20 ft lbs 25 27 Nm NOTE If using a chuck be sure the chuck jaws locate on the flats on the boring head shaft 5 Center the shaft of the boring head into the chuck or collet of the drill press or milling machine Tighten the chuck or collet and remove the wood block from the boring head assembly 6 Clamp the assembly to the drill press or machining table Use the holes in the engine cradle base plate for clamping 5 of 9 if possible If it is not possible use C clamps or similar clamps to secure the assembly NOTE When raising and lowering the boring head to check for binding ensure that the boring head and tool bits do not strike the engine crankcase Damage to the tool or crankcase may result 7 Lubricate the two guide dowels of the boring head assembly with light oil Raise and lower the boring head to ensure that there is no binding in the motion 8 Set the drill s or machine s speed to approximately 600 800 RPMs Ensure the boring head is fully raised then start the drill or machine Check the boring head and the table for vibration If there are no vibrations the drill speed can be increased If there are vibrations reduce the drill speed 600 800 RPMs is the recommended drill speed NOTE Boring with a slow and steady feed rate will provide cleaner finish 9 Bore the engine crankcase as follows a While applying cutting fluid as necessary begin boring with a slow
8. ase with a 1 1 2 2 in 38 50 mm wood block between boring head assembly plates to prevent the boring head from contacting the engine crankcase see Figure 7 b Lubricate two screws 10 with SAE 20w50 Harley Davidson motorcycle oil Install but do not tighten the two screws then place a piece of paper between the neighboring crankcase cylinder dowel and the locating plate c Tighten the screws to 18 20 ft lbs 25 27 Nm then ensure the paper moves freely between the cylinder dowel and the support plate If the paper does not move freely the cylinder dowel is too high and the dowel must be installed deeper or removed If the cylinder dowel is damaged during removal it will need to be replaced d Remove two screws 10 and the boring head assembly e Repeat Step 14 for opposite cylinder 15 See the appropriate Boring Head Setup section below and setup the boring head for your application is03459 Set screw outward locking Set screw inward locking Set screw depth Rough cut tool bit Finish cut tool bit Boring diameter Finish cut and boring head width Rough cut and boring head width Rough cut 10 Finish cut PONOARYONH is03455 1 Depth adjustment screw 2 Cylinder dowel reliefs 11 Boring head diameter Figure 4 Boring Head View of Bottom Side J04198 Figure 5 Boring Head Assembly Boring Head Setup Spigot Bore NOTES It is recommended that no
9. cMOTOR HARLEY DAVIDSON WY J04198 INSTRUCTIONS REV 2007 05 25 TWIN CAM CRANKCASE BORING TOOL GENERAL Kit Number 94419 06 Models This tool can be used to modify 1999 and later Twin Cam engines Additional Tools and Materials Required e Hex wrenches 1 8 in 3 16 in 1 4 in and 5 16 in e 7 16 in wrench e Torque wrench e 1 2 in socket e Calipers e Heavy duty 15 inch drill press or milling machine e Cutting fluid e Harley Davidson SAE 20w50 motorcycle oil NOTICE The procedures in this instruction sheet should be per formed by one experienced in precision measuring tech niques Failure to meet tolerances called for in this instruction sheet can result in engine damage 00511b WARNING The rider s safety depends upon the correct installation of this kit Use the appropriate service manual procedures If the procedure is not within your capabilities or you do not have the correct tools have a Harley Davidson dealer perform the installation Improper installation of this kit could result in death or serious injury 00333a NOTE This instruction sheet references Service Manual information A Service Manual for your model motorcycle is required for this installation and is available from a Harley Davidson Dealer Kit Contents See Figure 10 and Table 1 ENGINE AND TOOL PREPARATION 1 Refer to the appropriate Service Manual and remove and disassemble the engine J04198 NOTE Whe
10. ee the Instruction Sheet for the cylinder kit being installed to determine final spigot bore depth b Using a 1 8 inch hex key wrench and a 7 16 inch wrench adjust the stop depth adjustment screw 19 on the boring assembly c Measuring from the finish cut tool bit to the bottom of the locating plate as shown in Figure 5 adjust the stop depth adjustment screw so that the finish tool bit will cut to the desired depth d Secure stop depth adjustment screw 19 with nut 20 J04198 Boring Head Setup O Ring Counterbore Where Applicable NOTES It is recommended that no more than 0 125 in 3 175 mm of the diameter be removed in one pass The engine crankcase machining may require more than one pass and more than one boring head set up to obtain the final bore Attempting to remove more than the recommended amount of material in one pass may result in a rough finish and or damage to the bore and tool bit If the tool bit is set for a bore larger than 4 45 in 113 03 mm the tool bit will contact and cause damage to the inner diameter of the locating plate Item 5 Figure 10 and or tool bit Item 16 Figure 10 Due to the shallow depth of the O ring counterbore cut only the finish cut tool bit will be installed Two passes will be necessary to achieve the final cut dimension 1 See Figure 4 Install the finish cut tool bit into the bore head and set boring diameter as follows Do NOT install the rough cut tool bit w
11. gine Crankcase Bolt Hole Modification J04198 70f9 SERVICE PARTS Figure 10 Service Parts for Twin Cam Crankcase Boring Tool J04198 8 of 9 Table 1 Service Parts Table Item Description Quantity Part Number Support plate left early 94428 06 2 Base plate 94433 06 3 Support plate right 94440 06 4 Boring head 94460 06 5 Locating plate 94469 06 6 Support plate boring assembly 94470 06 7 Support plate left late 94515 06 8 Shielded bearing 7 8 X 2 X 9 16 in 94547 06 9 Dowel pull out 1 2 X 3 1 2 in 94516 06 10 Socket head cap screw 3 8 16 X 1 in 9 4659 11 Socket head cap screw 1 4 20 X 1 in 4 4661 12 Dowel pin 1 4 X 3 4 in 4 94526 06 13 Bushing 0 502 in I D X 0 75 O D X 0 75 Long 2 94541 06 14 Socket head cap screw 5 16 18 X 1 in 3 4662 15 T pin 3 8 in shaft 94551 06 16 Tool bit carbide 3 8 in 2 94552 06 17 Set screw 1 4 28 X 1 2 in 6 4663 18 Washer 1 4 in 6927 19 Set screw 5 16 18 X 1 3 4 in 4664 20 Nut 5 16 18 8086 21 Button head cap screw 1 4 20 X 1 2 in 4665 22 Dowel pin 1 2 X 3 1 2 in 94559 06 23 Washer 3 8 in 3 6920 24 Socket head cap screw 5 16 18 X 2 1 4 in 4672 25 Flange screw 1093 26 Washer 5 16 in 6933 J04198 9 of 9
12. hen cutting the O ring counterbore a See the Instruction Sheet for the cylinder kit being installed to determine final O ring counterbore dia meter Subtract the stock O ring counterbore diameter from the final O ring counterbore diameter to determine the diameter difference Divide by two to determine radius difference The finish tool bit protrusion for the first pass is the finish O ring counterbore radius less 1 2 the radius difference less the boring head radius The finish tool bit protrusion for the second pass is the finish O ring counterbore radius less the boring head radius b Setthe finish cut 5 tool bit depth using the set screw 3 Use an appropriate measuring tool to ensure accurate measurements c While ensuring that the tool bit is pressed tight to the depth set screw 3 tighten the locking set screw 1 then locking set screw 2 Tighten locking set screws to 90 in Ibs 10 Nm 4of9 2 Set the boring head O ring counterbore depth as follows a See the Instruction Sheet for the cylinder kit being installed to determine final O ring counterbore depth b See Figure 10 Remove the stop depth adjustment screw 19 nut 20 and washer 26 c Install washer 26 and nut 20 onto the alternate stop depth adjustment screw 24 then install the screw so the head of the screw is between the plates of the boring head assembly d Using a 1 8 inch hex key wrench and a 7 16 inch wrench adjust the s
13. ing head down very slowly When the stop bottoms out STOP Do not apply pressure to the cutting head after the stop bottoms out 16 For O ring counterbore where applicable a See the Boring Head Setup O Ring Counterbore section of this Instruction Sheet and setup boring head assembly for O ring counterbore first pass Note only the finish cut tool bit will be used for this bore b See Step 5 of this section and assemble the boring head assembly onto the engine crankcase c Repeat the Boring Procedure above and bore the O ring counterbore Note that a minimum of two passes will be required for each cylinder d Repeat Steps 16a 16c with boring head assembly setup for second pass bore cut adjusted for dimensional runout see note at beginning of sec tion 17 Remove engine crankcase tool assembly from the drill press or milling machine Remove engine crankcase from tool NOTE To prevent severe engine damage thoroughly clean and remove all chips and debris from the engine crankcase after boring 18 Disassemble crankcase and wash or clean chips and debris from engine crankcase halves necessary 19 See Figure 9 Using a 11 32 inch drill bit drill out the existing threads of the top center screw hole Drill to a depth of 0 79 inches from the gasket surface 20 Using a size F in drill bit extend the top center screw hole 1 00 in 25 4 mm maximum to a depth of 1 79 in 45 46 mm from the gasket surf
14. ispose of materials responsibly 8 10 11 12 13 For later model engines 2006 and later Dyna models 2007 and later Softail and Touring models Use left support plate 7 c Install left support plate 1 or 7 to base plate 2 with four screws 10 for early models or three screws for later models Tighten screws to 120 in Ibs 13 Nm d Determine which side of the right support plate should face the engine cradle assembly If boring an unbal anced Alpha engine or a 2007 or later Softail engine ensure side A faces outward away from the engine cradle If boring a balanced Beta engine except a 2007 or later Softail engine ensure side B faces outward away from the engine cradle e Install right support plate 8 with the appropriate side facing the engine cradle assembly to the base plate 2 with three screws 10 and washers 23 Tighten screws to 120 in Ibs 13 Nm Install the engine case into the engine cradle Rotate the engine case so that either the front or rear cylinder deck is facing up and horizontal Lubricate two 1 4 inch screws 11 with SAE 20w50 Harley Davidson motorcycle oil If the front cylinder is being bored install the screws in the right support plate holes marked F If the rear cylinder is being bored install the screws in the alignment plate holes marked R This will align the cylinder spigot bore perpendicular to the base Do not tighten at this time Lubricate two
15. n reassembling the engine Harley Davidson recommends replacing the Original Equipment cylinder studs with Screamin Eagle High Tensile Studs 16505 01 e H is03456 amp Many Harley Davidson Parts amp Accessories are made of plastics and metals which can be recycled Figure 1 Cylinder Wall 2 Remove cylinder studs from the engine crankcase 3 Mask off all bearings and oil holes to prevent debris and contaminants from entering those areas 4 Inspect and clean engine case mating surfaces 5 Bolt engine case together with the stock hardware except the top center screw between the cylinders Figure 2 and tighten to the specifications listed in the Service Manual NOTE To prevent damage to tool it is important to replace the stock top center screw with the top center screw included in this kit Part Number 1093 6 See Figure 10 Install the top center screw 25 included with this kit between the cylinders and tighten to 50 90 in Ibs 5 6 10 2 Nm NOTE When assembling the engine cradle lubricate all of the hard ware with clean SAE 20w50 Harley Davidson motorcycle oil 7 See Figure 10 Assemble the engine cradle as follows a Ensure all mating surfaces are clean b Determine which left support plate to use for in the engine cradle assembly For early model engines 1999 2005 Dyna models 1999 2006 Touring models and 2000 2006 Softail Use left side support plate 1 1 of 9 Please d
16. top depth adjustment screw 24 on the boring assembly top plate down to the locating plate e Measuring from the finish cut tool bit to the bottom of the locating plate as shown in Figure 5 adjust the stop depth adjustment screw so that the finish tool bit will cut to the desired depth f Secure stop depth adjustment screw 24 with nut 20 is03457 is03517 1 O ring bore 2 Spigot bore Figure 8 Cylinder Spigot and O Ring Counterbore Dimensions J04198 BORING PROCEDURE NOTES For best boring results use a well maintained and dependable drill press or milling machine If you use equipment of poor quality or condition inaccurate boring may result For applications requiring an O ring counterbore cut the spigot bore before cutting the O ring counterbore All boring operations have some degree of dimensional runout This runout should be assessed and adjusted for by performing a test cut or after a first pass Determine dimensional runout as follows e After the first pass or test cut measure the bore actual cut diameter then subtract the actual cut diameter from the intended diameter and divide by 2 e Example If the actual cut diameter measures 4 362 in and the intended diameter was 4 358 in then the bore is 0 004 in over size 4 362 in 4 358 in 0 004 in Divide by 2 to determine dimensional runout adjustment 0 004 in 2 0 002 in In this example when setting
Download Pdf Manuals
Related Search