INT-39, "Removal and Installation"
Contents
1. TEER Continue to page 2 of the worksheet and briefly describe the location of the noise or rattle In addition please indicate the conditions which are present when the noise occurs PIIB8741E Revision 2010 May INT 11 2011 QX56 SQUEAK AND RATTLE TROUBLE DIAGNOSES SYMPTOM DIAGNOSIS gt SQUEAK amp RATTLE DIAGNOSTIC WORKSHEET page 2 Briefly describe the location where the noise occurs Il WHEN DOES IT OCCUR please check the boxes that apply CT anytime after sitting out in the rain 1st time in the morning L when it is raining or wet only when it is cold outside L dry or dusty conditions only when it is hot outside O other Ill WHEN DRIVING IV WHAT TYPE OF NOISE through driveways LI squeak like tennis shoes on a clean floor LI over rough roads L creak like walking on an old wooden floor LI over speed bumps rattle like shaking a baby rattle L only about mph L knock like a knock at the door L on acceleration L tick like a clock second hand L coming to a stop LI thump heavy muffled knock noise on turns left right or either circle buzz like a bumble bee L with passengers or cargo other afterdriving milesor minutes TO BE COMPLETED BY DEALERSHIP PERSONNEL Test Drive Notes YES NO Initials of person performing Vehicle test driven with cus2. Revision 2010 May INT 17 2011 QX56 BODY SIDE TRIM REMOVAL AND INSTALLATION gt BODY SIDE TRIM E X p od ed V i ew INFOID 0000000006220245 SEC 769 JMJIA4307ZZ 1 Front pillar garnish 2 Assist grip 3 Assist grip cap Dash side finisher 5 Clip 6 Front kicking plate inner Front body side welt 8 Front kicking plate outer 9 Center pillar lower garnish 10 Rear side bracket 11 Rear kicking plate inner 12 Rear body side welt 13 Rear kicking plate outer 14 Assist grip 15 Center pillar upper garnish i Clip Zx Paw 1 1 Metal clip Refer to Gl 4 Components for symbols in the figure DASH SIDE FINISHER DASH SIDE FINISHER Removal and Installation INFOID 0000000006220246 CAUTION e When removing always use a remover tool that is made of plastic Never damage the body REMOVAL 1 Remove front kicking plate inner Refer to INT 20 KICKING PLATE INNER Removal and Installation 2 Remove dash side finisher fixing clip A Revision 2010 May INT 18 2011 QX56 BODY SIDE TRIM REMOVAL AND INSTALLATION gt 3 Disengage dash side finisher 1 fixing clips A using a remover tool B as shown by the arrow in the figure and then remove dash side finisher Clip INSTALLATION Note the following items and install in the reverse order of removal CAUTION Visually check the clips for deformation and damage during installation Replace with new ones if necessary e When ins
3. eene 39 REAR PILLAR FINISHER seen 37 Exploded View annae ener eneneneeneneenenn 39 Removal and Installation 39 Revision 2010 May INT 2 2011 QX56 PRECAUTIONS PRECAUTION gt PRECAUTION PRECAUTIONS Precaution for Supplemental Restraint System SRS AIR BAG and SEAT BELT P H E T E N S O N E R INFOID 00000000064 15653 The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE TENSIONER used along with a front seat belt helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision This system includes seat belt switch inputs and dual stage front air bag modules The SRS system uses the seat belt switches to determine the front air bag deployment and may only deploy one front air bag depending on the severity of a collision and whether the front occupants are belted or unbelted Information necessary to service the system safely is included in the SRS AIR BAG and SEAT BELT of this Service Manual WARNING To avoid rendering the SRS inoperative which could increase the risk of personal injury or death in the event of a collision that would result in air bag inflation all maintenance must be performed by an authorized NISSAN INFINITI dealer Improper maintenance including incorrect removal and installation of the SRS can lead to personal injury caused by unintentional activat
4. AJ Pawl Es 1 1 Metal clip JMJIA4021ZZ Rear kicking plate inner 1 Disengage rear kicking plate inner fixing pawls using a remover tool A as shown by the arrow in the fig ure and then remove rear kicking plate inner 1 CAUTION Revision 2010 May INT 20 2011 QX56 BODY SIDE TRIM REMOVAL AND INSTALLATION Apply protective tape B to the body panel to protect from damage JMJIA4023ZZ 2 Remove rear side bracket INSTALLATION Note the following items and install in the reverse order of removal CAUTION Visually check the pawls and metal clips for deformation and damage during installation Replace with new ones if necessary When installing front kicking plate inner and rear kicking plate inner check that pawls and metal clips are securely fitted in body panel holes and press them in KICKING PLATE OUTER KICKING PLATE OUTER Removal and Installation INFOID 0000000008220250 CAUTION e When removing always use a remover tool that is made of plastic Never damage the body REMOVAL Front kicking plate outer Disengage front kicking plate outer fixing pawls using a remover tool A as shown by the arrow in the figure and then remove front kick ing plate outer 1 CAUTION Apply protective tape B to the body panel to protect from dam age A Pawl Lod JMJIA4022ZZ Rear kicking plate outer Disengage rear kicking plate outer fixing pawls using a remover tool A as sho
5. 0 984 in pad 68239 13E00 5 mm 0 197 in wide tape roll The following materials not found in the kit can also be used to repair squeaks and rattles UHMW TEFLON TAPE Insulates where slight movement is present Ideal for instrument panel applications SILICONE GREASE Used in place of UHMW tape that is visible or does not fit Only lasts a few months SILICONE SPRAY Used when grease cannot be applied DUCT TAPE Used to eliminate movement CONFIRM THE REPAIR After repair is complete test drive the vehicle to confirm that the cause of noise is repaired by test driving the vehicle Operate the vehicle under the same conditions as when the noise originally occurred Refer to the notes on the Diagnostic Worksheet Inspection Procedure INFOID 0000000006220270 Refer to Table of Contents for specific component removal and installation information INSTRUMENT PANEL Most incidents are caused by contact and movement between 1 The cluster lid A and instrument panel Acrylic lens and combination meter housing Instrument panel to front pillar garnish Instrument panel to windshield Instrument panel mounting pins Wiring harnesses behind the combination meter NDT Rol A C defroster duct and duct joint These incidents can usually be located by tapping or moving the components to duplicate the noise or by MINE pressing on the components while driving to stop the noise Most of these incidents can be repaired by applying felt cloth tape or sil
6. 9 FLOOR TRIM eeenenh ihnen enn nnnm anna nete n nua n n nnn nenun ennnen 24 Diagnostic Worksheet nanne 11 Exploded View sss 24 REMOVAL AND INSTALLATION 13 FRONT FLOOR CARPET eene 25 FRONT FLOOR CARPET Removal and Installa FRONT DOOR FINISHER Ke 13 lO BE 25 EE 1 EE EE E ia REAR FLOOR CARPET ne 27 REAR FLOOR CARPET Removal and Installa REAR DOOR FINISHER nn 16 OM EE 27 Exploded View 16 HEADLINING ener 28 SE 1g Exploded View AANEREN 28 BODY SIDE TRIM aaneen nennen 18 Removal and Installation esses 29 Exploded View eese 18 LUGGAGE FLOOR TRIM sn 33 DASH SIDE FINISHER eee 18 Exploded VIQW ss saar x iiti tione AR SAATANAN 33 Revision 2010 May INT 1 2011 QX56 LUGGAGE FLOOR REAR BOARD 34 REAR PILLAR FINISHER Removal and Installa LUGGAGE FLOOR REAR BOARD Removal and MOM EE 37 EC UE Ur WEE 34 BACK PILLAR GARNISH eenen 37 LUGGAGE REAR PLATE enen 35 BACK PILLAR GARNISH Removal and Installa LUGGAGE REAR PLATE Removal and Installa O E 37 e LS ED METRE 35 LUGGAGE SIDE UPPER FINISHER dd LUGGAGE SIDE LOWER FINISHER 36 LUGGAGE SIDE UPPER FINISHER Removal LUGGAGE SIDE LOWER FINISHER Removal and Installation 38 and Installation 36 BACK DOOR TRIM
7. Components that pass through the engine wall Engine wall mounts and connectors Loose radiator mounting pins Hood bumpers out of adjustment Hood striker out of adjustment These noises can be difficult to isolate since they cannot be reached from the interior of the vehicle The best method is to secure move or insulate one component at a time and test drive the vehicle Also engine RPM or load can be changed to isolate the noise Repairs can usually be made by moving adjusting securing or insulating the component causing the noise OT A ON Revision 2010 May INT 10 2011 QX56 SQUEAK AND RATTLE TROUBLE DIAGNOSES SYMPTOM DIAGNOSIS Diagnostic Worksheet INFOID O000000006220271 SQUEAK amp RATTLE DIAGNOSTIC WORKSHEET INFINITI Dear Infiniti Customer We are concerned about your satisfaction with your Infiniti vehicle Repairing a squeak or rattle sometimes can be very difficult To help us fix your Infiniti right the first time please take a moment to note the area of the vehicle where the squeak or rattle occurs and under what conditions You may be asked to take a test drive with a service consultant or technician to ensure we confirm the noise you are hearing l WHERE DOES THE NOISE COME FROM circle the area of the vehicle The illustrations are for reference only and may not reflect the actual configuration of your vehicle 99
8. Removal and Installation Revision 2010 May INT 29 2011 QX56 HEADLINING REMOVAL AND INSTALLATION gt 6 Disconnect harness connectors Lane camera unit harness connector 1 if equipped Inside mirror harness connector 2 Light amp rain sensor harness connector rain sensor harness connector 3 7 Remove assist grips Insert a small flat bladed screwdriver A into the gap between assist grip cap 1 and then remove assist grip cap Remove assist grip mounting bolts and then remove assist grips 2 JMJIA4063ZZ 8 Insert a remover tool A between luggage room lamp 1 and roof garnish to disengage the fixing metal clips and then discon nect luggage room lamp harness connector CAUTION Apply protective tape B to the roof garnish to protect from damage 1 Metal clip 9 Insert a remover tool A between roof garnish 1 and body panel to disengage the fixing clips and pawls and then remove roof garnish JMJIA4066ZZ 10 Remove front pillar garnish LH and RH Refer to INT 19 FRONT PILLAR GARNISH Removal and Installation 11 Remove front kicking plate inner LH and RH and rear kicking plate inner LH and RH Refer to INT 20 KICKING PLATE INNER Removal and Installation 12 Remove dash side finisher LH and RH Refer to INT 18 DASH SIDE FINISHER Removal and Installa tion 13 Remove center pillar lower garnish LH and RH Refer to INT 22 CENTER PILLAR LOWER GARNI
9. diagnosis and repair the noise that the customer is Ou concerned about This can be accomplished by performing a test drive with the customer After identifying the type of noise isolate the noise in terms of its characteristics The noise characteristics are provided so that the customer service adviser and technician use the same language when describing the noise Squeak Like tennis shoes on a clean floor Squeak characteristics include the light contact fast movement brought on by road conditions hard sur faces high pitched noise softer surfaces low pitched noises edge to surface chirping Creak Like walking on an old wooden floor Creak characteristics include firm contact slow movement twisting with a rotational movement pitch dependent on materials often brought on by activity Rattle Like shaking a baby rattle Rattle characteristics include fast repeated contact vibration or similar movement loose parts missing clip or fastener incorrect clearance Knock Like a knock on a door Knock characteristics include hollow sounds sometimes repeating often brought on by driver action Tick Like a clock second hand Tick characteristics include gentle contacting of light materials loose components can be caused by driver action or road conditions Thump Heavy muffled knock noise Thump characteristics include softer knock dull sounds often brought on by activity Buzz
10. disengage front door grip cap fixing pawls as shown by the arrow in the figure and then remove fixing screws A Pawl bad 4 Remove step lamp and then disconnect step lamp harness connector Refer to INL 74 Removal and Installation 5 Remove bumper rubber 6 Insert a remover tool A between door finisher and door panel to disengage fixing clips and metal clip as shown by the arrow in the figure T Clip i Metal clip CAUTION j Insert a remover tool into the part shown in the figure A between the clips and the door panel S JMJIA4015ZZ 7 Disconnect BSW BSI indicator harness connector 8 Disconnect seat memory switch harness connector 9 Disconnect mood lamp harness connector 10 Disconnect power window switch harness connector and clamp 11 Disconnect lock knob cable and inside handle cable from front door inside handle 12 Remove front door finisher from front door panel 13 Remove the following parts after removing front door finisher Mood lamp Door mirror corner cover Power window switch Refer toPWC 74 Removal and Installation BSW BSI indicator Refer to DAS 525 Removal and Installation Revision 2010 May INT 14 2011 QX56 FRONT DOOR FINISHER REMOVAL AND INSTALLATION gt Seat memory switch Refer to ADP 137 Removal and Installation Front door inside handle Refer to DLK 241 INSIDE HANDLE Removal and Installation INSTALLATION Note the following
11. front kicking plate inner and rear kicking plate inner Refer to INT 20 KICKING PLATE INNER Removal and Installation 2 Remove dash side finisher Refer to INT 18 DASH SIDE FINISHER Removal and Installation 3 Slide front seat assembly to the frontmost position 4 Remove center pillar lower garnish Refer to INT 22 CENTER PILLAR LOWER GARNISH Removal and Installation 5 Remove front body side welt Rear body side welt 1 Remove front kicking plate inner and rear kicking plate inner Refer to INT 20 KICKING PLATE INNER Removal and Installation 2 Slide front seat assembly to the frontmost position 3 Remove center pillar lower garnish Refer to INT 22 CENTER PILLAR LOWER GARNISH Removal and Installation 4 Remove luggage side lower finisher Refer to INT 36 LUGGAGE SIDE LOWER FINISHER Removal and Installation 5 Remove rear body side welt INSTALLATION Install in the reverse order of removal KICKING PLATE INNER KICKING PLATE INNER Removal and Installation IIFOIE 0000000006220249 CAUTION When removing always use a remover tool that is made of plastic Never damage the body REMOVAL Front kicking plate inner Disengage front kicking plate inner fixing pawls and metal clips using a remover tool A as shown by the arrow in the figure and then remove front kicking plate inner CAUTION Apply protective tape B to the body panel to protect from dam age
12. out the headlining 24 Remove the following parts after removing headlining assembly Revision 2010 May INT 31 2011 QX56 HEADLINING REMOVAL AND INSTALLATION gt Personal lamp assembly Refer to INL 77 Removal and Installation Rear ventilator grille assembly Refer to VTL 13 REAR VENTILATOR GRILLE Removal and Installa tion Headlining harness INSTALLATION Note the following items and install in the reverse order of removal CAUTION Becareful not to bend headlining when installing e First install metal clips of map lamp assembly and clips of the rear end of headlining for positioning Revision 2010 May INT 32 2011 QX56 LUGGAGE FLOOR TRIM REMOVAL AND INSTALLATION gt LUGGAGE FLOOR TRIM E X p od ed V i ew INFOID 0000000006220258 SEC 849 JMJIA4308ZZ 1 Rear pillar finisher LH 2 Luggage upper finisher LH 3 Luggage side lower finisher LH 4 Back pillar garnish LH 5 Rope hook 6 Clip 7 Luggage lower board LH 8 Luggage floor finisher LH 9 Luggage floor bracket Revision 2010 May INT 33 2011 QX56 LUGGAGE FLOOR TRIM lt REMOVAL AND INSTALLATION gt 10 Luggage floor board center 11 Tool box 12 Luggage rear plate 13 Luggage rear plate mask 14 Child anchor cover 15 Luggage floor finisher RH 16 Luggage lower board RH 17 Fold down switch 18 Back pillar garnish RH 19 Luggage side lower finisher RH 20 Luggage upper finisher RH 21 Rear pillar finisher RH 22 Recl
13. pillar lower garnish check that clips are securely fitted in body panel holes and press them in CENTER PILLAR UPPER GARNISH CENTER PILLAR UPPER GARNISH Removal and Installation WEE CAUTION When removing always use a remover tool that is made of plastic Never damage the body REMOVAL 1 Remove front kicking plate inner and rear kicking plate inner Refer to INT 20 KICKING PLATE INNER Removal and Installation 2 Slide front seat assembly to the frontmost position 3 Remove center pillar lower garnish Refer to INT 22 CENTER PILLAR LOWER GARNISH Removal and Installation Revision 2010 May INT 22 2011 QX56 BODY SIDE TRIM REMOVAL AND INSTALLATION gt 4 Disengage center pillar upper garnish lower side fixing clip using a remover tool A N NC 5 Pull center pillar upper garnish 1 from inside passenger room disengage center pillar upper garnish upper side fixing pawl as shown in the following figure and then remove center pillar upper garnish from center pillar panel 2 JMJIA1176ZZ Be careful not to apply excessive force when removing center pillar upper garnish Otherwise pawl may be damaged and fragments may drop in panel holes on body 6 Remove assist grip mounting bolts and then remove assist grip INSTALLATION Note the following items and install in the reverse order of removal CAUTION Replace center pillar upper garnish with a new part after removal Never
14. rod pin by hitting it Push Push m SE A Removal Removal 1 Screw out with a Phillips screwdriver 2 Remove female portion with E ex Revision 2010 May INT 6 lj D f A d flat bladed Wi e d SS ST screwdriver u lt 9 Clip Finisher Removal Removal Installation Rotate 45 to remove Removal Removal Removal 5 JMJIA3734GB 2011 QX56 SQUEAK AND RATTLE TROUBLE DIAGNOSES SYMPTOM DIAGNOSIS SYMPTOM DIAGNOSIS SQUEAK AND RATTLE TROUBLE DIAGNOSES Wo rk F OW INFOID 0000000006220269 Customer Interview v Duplicate the Noise and Test Drive v Check Related Service Bulletins v Locate the Noise and Identify the Root Cause k Repair the Cause v Confirm Repair OK E Inspection End SBT842 CUSTOMER INTERVIEW Interview the customer if possible to determine the conditions that exist when the noise occurs Use the Diag nostic Worksheet during the interview to document the facts and conditions when the noise occurs and any customer comments Refer to INT 11 Diagnostic Worksheet This information is necessary to duplicate the conditions that exist when the noise occurs The customer may not be able to provide a detailed description or the location of the noise Attempt to obtain all the facts and conditions that exist when the noise occurs or does not occur If there is more than one noise in the vehicle perform a
15. sure to carry out fitting adjustments to check their operation Check the lubrication level damage and wear of each part If necessary grease or replace it Revision 2010 May INT 4 2011 QX56 PREPARATION PREPARATION PREPARATION PREPARATION Special Service Tools INFOID 0000000006220267 The actual shapes of Kent Moore tools may differ from those of special service tools illustrated here Tool number Kent Moore No Description Tool name 933570 Locates the noise Chassis ear J 43980 NISSAN Squeak and Rattle Repairs the cause of noise Kit SIIA0994E Commercial Service Tools INFOID 0000000006220265 Tool name Description Engine ear Locates the noise Remover tool Removes clips pawls and metal clips JMKIA3050ZZ Revision 2010 May INT 5 2011 QX56 PREPARATION gt CLIP LIST Clip List CLIP LIST INFOID 0000000006220237 t Remove with a clip remover Shapes Removal amp Installation Shapes Removal amp Installation Removal Removal Remove by bending up with Clip A Finisher Clip A flat bladed screwdrivers or clip remover las gd AE Clip B Flat bladed screwdriver Clip B Removal Flat bladed Finisher screwdriver We Body panel Clip B Clip A Grommet Remove by bending up with flat bladed screwdrivers or clip remover Removal Installation Removal Push center pin to Holder portion of clip must be ee spread out to remove
16. 0262 REMOVAL 1 Remove luggage side lower finisher INT 36 LUGGAGE SIDE LOWER FINISHER Removal and Instal lation 2 Disengage lower side of rear pillar finisher fixing clip 3 Pull rear pillar upper garnish 1 from inside passenger room disengage rear pillar upper garnish upper side fixing pawl as shown in the following figure and then remove rear pillar upper garnish from body panel 2 JMJIA1176ZZ CAUTION Be careful not to apply excessive force when removing rear pillar finisher Otherwise pawl may be damaged and fragments may drop in body panel holes on body INSTALLATION Note the following items and install in the reverse order of removal CAUTION Replace rear pillar finisher with a new part after removal Never reuse rear pillar finisher Visually check the clip and pawl for deformation and damage during installation Replace with new ones if necessary e When installing rear pillar finisher check that clip and pawl are securely fitted in body panel holes and press them in BACK PILLAR GARNISH BACK PILLAR GARNISH Removal and Installation INFOID 0000000006220263 REMOVAL 1 Remove luggage side lower finisher INT 36 LUGGAGE SIDE LOWER FINISHER Removal and Instal lation 2 Remove cap of back door finisher side LH and then remove stud ball Refer to DLK 247 BACK DOOR SUPPORT ROD Removal and Installation LH side only 3 Disengage back pillar garnish 1 fixing clips and pawl us
17. 4236ZZ 1 Rear ventilator grille RH 2 Rear ventilator base RH 3 Rear ventilator garnish B RH 4 Rear ventilator garnish A RH 5 Assist grip 6 Assist grip cap 7 Sun visor cover RH 8 Sun visor assembly RH 9 Sun visor assembly LH Revision 2010 May INT 28 2011 QX56 HEADLINING REMOVAL AND INSTALLATION gt 10 Sun visor cover LH 11 Map lamp bracket 12 Dual lock fastener 13 Rear ventilator base LH 14 Rear ventilator grille LH 15 Roof garnish 16 Headlining assembly 17 Dual lock fastener 18 Dual lock fastener 19 Map lamp assembly 20 Sum visor holder RH 21 Rain sensor cover 22 Front camera finisher 23 Sum visor holder LH 24 Rear ventilator garnish A LH 25 Rear ventilator garnish B LH 26 Front camera finisher with LDP LDW Clip Pawl p 1 Metal clip Re m oval a n d n stal ati O n INFOID 0000000006220257 REMOVAL 1 Remove sun visor cap 1 using a remover tool A and then remove sunvisor assembly fixing TORX screws JMJIA4055ZZ 2 Disconnect vanity mirror lamp harness connector and then remove sun visor assembly LH and RH 3 Rotate sun visor holder 1 LH and RH at approximately 90 degrees and then pull it out to remove JMJIA4061ZZ 4 Insert a remover tool A into the gap between lane camera fin isher 1 and then remove lane camera finisher if equipped Pawl Ex JMJIA4053ZZ 5 Remove light 8 rain sensor cover rain sensor cover Refer to WW 72
18. 9 SEAT BELT RETRACTOR Removal and Installation 5 Remove luggage floor board center and both luggage lower boards Refer to INT 34 LUGGAGE FLOOR REAR BOARD Removal and Installation 6 Remove luggage rear plate Refer to INT 35 LUGGAGE REAR PLATE Removal and Installation 7 Remove rope hook 1 mounting bolt using a socket wrench A and then remove rope hook JMJIA4043ZZ 8 Disengage luggage side lower finisher fixing clip 1 using a small flat bladed screwdriver A as shown by the arrow in the figure and then remove clip 9 Remove luggage side lower finisher 1 Disengage luggage side lower finisher 1 fixing clips and pawls 3 Clip Zx Pawl 2 Disconnect luggage room power socket harness connector LH side only 3 Disconnect fold down switch harness connector RH side only 4 Disconnect reclining switch harness connector LH and RH 5 Remove luggage side lower finisher INSTALLATION Note the following items and install in the reverse order of removal CAUTION Revision 2010 May INT 36 2011 QX56 LUGGAGE FLOOR TRIM REMOVAL AND INSTALLATION Visually check the clips and pawls for deformation and damage during installation Replace with new ones if necessary e When installing luggage side lower finisher check that clips and pawls are securely fitted in body panel holes and press them in REAR PILLAR FINISHER REAR PILLAR FINISHER Removal and Installation INFOID 000000000622
19. BODY INTERIOR SECTION N INTERIOR PREGAUTION cius qiti ona eet 3 DASH SIDE FINISHER Removal and Installation 18 PRECAUTIONS eese eene nnne nnn 3 Precaution for Supplemental Restraint System FRONT PILLAR GARNISH Se Eed EENS EE SEN 19 SRS AIR BAG and SEAT BELT PRE TEN FRONT PILLAR GARNISH Removal and Instal SIONERM Seren tet MLA Ent adat nes ed an 3 EN Lal KEEN 19 Precaution Necessary for Steering Wheel Rota BODY SIDE WELT ea IA 20 tion after Battery Disconnect Em 3 BODY SIDE WELT Removal and Installation 20 Precaution for Procedure without Cowl Top Cover 4 Precaution for Work 4 KICKING PLATE INNER een nnn 20 KICKING PLATE INNER Removal and Installa PREPARATION eren 5 Nel EE 20 PREPARATION Een 5 KICKING PLATE OUTER EE 21 Special Service Tools nanne eneen eneen 5 KICKING PLATE OUTER Removal and Installa Commercial Service Tools s EN Ane 21 CLIP LIST zaisrersserrsen geet rnenerene nen aans EES NEVE ENER zaan 6 CENTER PILLAR LOWER GARNISH 22 Clip List since een lei ein 6 CENTER PILLAR LOWER GARNISH Removal and Installation anneer nen 22 SYMPTOM DIAGNOSIS 7 CENTER PILLAR UPPER GARNISH 22 SQUEAK AND RATTLE TROUBLE DIAG CENTER PILLAR UPPER GARNISH Removal NOSES E 7 and Installation nnen ennen ennen 22 Work Oe UE 7 Inspection Procedure sese
20. LLATION 2 Remove back door finisher inner lower 6 Disengage back door finisher side 1 fixing metal clips using a remover tool A and then remove back door finisher side 1 Metalclip 7 Disengage back door finisher upper 1 fixing metal clips using a remover tool A and then remove back door finisher upper 1 Metal clip JMJIA4051ZZ INSTALLATION Note the following items and install in the reverse order of removal CAUTION Visually check the clips pawls and metal clips for deformation and damage during installation Replace with new ones if necessary e When installing back door trims check that clips pawls and metal clips are securely fitted in body panel holes and press them in INT Revision 2010 May INT 41 2011 QX56
21. Like a bumblebee Buzz characteristics include high frequency rattle firm contact Often the degree of acceptable noise level varies depending upon the person A noise that a technician may judge as acceptable may be very irritating to a customer Weather conditions especially humidity and temperature may have a great effect on noise level DUPLICATE THE NOISE AND TEST DRIVE Revision 2010 May INT 7 2011 QX56 SQUEAK AND RATTLE TROUBLE DIAGNOSES SYMPTOM DIAGNOSIS If possible drive the vehicle with the customer until the noise is duplicated Note any additional information on the Diagnostic Worksheet regarding the conditions or location of the noise This information can be used to duplicate the same conditions when the repair is reconfirmed If the noise can be duplicated easily during the test drive do the following with the vehicle stopped to help identify the source of the noise 1 Close a door 2 Tap or push pull around the area where the noise appears to be coming from 3 Rev the engine 4 Use a floor jack to recreate vehicle twist 5 At idle apply engine load electrical load half clutch on M T models drive position on A T models 6 Raise the vehicle on a hoist and hit a tire with a rubber hammer Drive the vehicle and attempt to duplicate the conditions the customer states exist when the noise occurs If it is difficult to duplicate the noise drive the vehicle slowly on an undulating or rou
22. RH JMJIA4225ZZ 14 Disengage front floor carpet from front floor carpet fixing clips A JMJIA1560ZZ Revision 2010 May INT 26 2011 QX56 FLOOR TRIM REMOVAL AND INSTALLATION gt 15 Peel off dual lock fastener between front floor carpet and rear floor carpet and then remove front floor car pet INSTALLATION Install in the reverse order of removal REAR FLOOR CARPET REAR FLOOR CARPET Removal and Installation INFOID 0000000006220255 REMOVAL 1 Remove third seat assembly Refer to SE 138 Removal and Installation 2 Remove luggage floor rear board Refer to INT 34 LUGGAGE FLOOR REAR BOARD Removal and Installation 3 Remove luggage rear plate Refer to INT 35 LUGGAGE REAR PLATE Removal and Installation Remove luggage floor bracket Refer to INT 33 Exploded View 5 Remove luggage side lower finisher Refer to INT 36 LUGGAGE SIDE LOWER FINISHER Removal and Installation 6 Disengage clip of each floor hook 1 using a remover tool A and then remove each floor hook A Clip LON E JMJIA0092GB 7 Peel off dual lock fastener between front floor carpet and rear floor carpet and then remove rear floor car INT pet INSTALLATION Install in the reverse order of removal Revision 2010 May INT 27 2011 QX56 HEADLINING REMOVAL AND INSTALLATION gt HEADLINING E X p od ed V i ew INFOID 0000000006220256 SEC 253 738 964 JMJIA
23. SH Removal and Installation Revision 2010 May INT 30 2011 QX56 HEADLINING REMOVAL AND INSTALLATION 14 Remove luggage side lower finisher LH and RH Refer to INT 36 LUGGAGE SIDE LOWER FINISHER Removal and Installation 15 Remove front body side welt LH and RH and rear body side welt LH and RH Refer to INT 20 BODY SIDE WELT Removal and Installation 16 Remove center pillar upper garnish LH and RH Refer to INT 22 CENTER PILLAR UPPER GARNISH Removal and Installation 17 Remove rear pillar finisher LH and RH Refer to INT 37 REAR PILLAR FINISHER Removal and Installation 18 Remove back pillar garnish LH and RH Refer to INT 37 BACK PILLAR GARNISH Removal and Installation 19 Remove luggage side upper finisher LH and RH Refer to INT 38 LUGGAGE SIDE UPPER FINISHER Removal and Installation 20 Insert a remover tool between map lamp assembly 1 and headlining assembly to disengage the fixing metal clips and then remove map lamp assembly 1 Metal clip JMJIA4062ZZ 21 Peel off dual lock fastener between headlining assembly and roof panel 22 Remove headlining clips located at the rear side 23 Remove headlining assembly 1 through the back door Se jio ER a JMJIA4068ZZ CAUTION e When removing 2 workers are required Never bend headlining when removing Be careful not to scratch or damage any part of the body while taking
24. ecurely fitted in body panel holes and press them in Revision 2010 May INT 38 2011 QX56 BACK DOOR TRIM REMOVAL AND INSTALLATION gt BACK DOOR TRIM E X p od ed V i ew INFOID 0000000006220265 SEC 900 909 JMJIA4421ZZ 1 Back door finisher lower 2 Auto back door switch finisher 3 Pull handle Back door assembly 5 Back door finisher side RH 6 Back door finisher upper Back door finisher side LH 8 Cap 9 Lamp mask 10 Emergency handle mask a Clip Zx Pawl 7 Metal clip A 4 oa LI LI bea Re m oval a n d n stal ati O n INFOID 0000000006220266 REMOVAL 1 Fully open back door Revision 2010 May INT 39 2011 QX56 BACK DOOR TRIM REMOVAL AND INSTALLATION gt 2 Disengage pull handle finisher 1 fixing pawls using a remover tool A and then remove pull handle finisher Pawl ep ch L 3 Disengage auto back door switch finisher 1 fixing pawls using a remover tool A and then disconnect auto back door switch harness connector Pawl H J ex 4 Remove back door finisher inner lower 1 fixing clips A JMJIA4047ZZ 5 Remove the back door finisher inner lower 1 Disengage back door finisher inner lower 1 fixing clips and pawls using a remover tool A JMJIA4050ZZ D Clip Zx Pawl NOTE Start disengaging from the position where pawls are located as shown in the figure Revision 2010 May INT 40 2011 QX56 BACK DOOR TRIM REMOVAL AND INSTA
25. gh road to stress the vehicle body CHECK RELATED SERVICE BULLETINS After verifying the customer concern or symptom check ASIST for Technical Service Bulletins TSBs related to the concern or symptom If a TSB relates to the symptom follow the procedure to repair the noise LOCATE THE NOISE AND IDENTIFY THE ROOT CAUSE 1 Narrow down the noise to a general area To help pinpoint the source of the noise use a listening tool Chassis ear J 39570 engine ear and mechanics stethoscope 2 Narrow down the noise to a more specific area and identify the cause of the noise by Removing the component s in the area s that is are suspected to be the cause of the noise Do not use too much force when removing clips and fasteners otherwise clips and fasteners can be broken or lost during the repair creating a new noise Tapping or pushing pulling the component s that is are suspected to be the cause of the noise Do not tap or push pull the component s with excessive force otherwise the noise is eliminated only tempo rarily Feeling for a vibration by hand by touching the component s that is are suspected to be the cause of the noise Placing a piece of paper between components that are suspected to be the cause of the noise Looking for loose components and contact marks Refer to INT 9 Inspection Procedure REPAIR THE CAUSE If the cause is a loose component tighten the component securely If the cause is insuffic
26. icon spray in hard to reach areas Urethane pads can be used to insulate wiring harness CAUTION Never use silicone spray to isolate a squeak or rattle If the area is saturated with silicone the recheck of repair becomes impossible CENTER CONSOLE Components to check include 1 Shifter assembly cover to finisher 2 A C control unit and cluster lid C 3 Wiring harnesses behind audio and A C control unit The instrument panel repair and isolation procedures also apply to the center console DOORS Check the following items 1 Finisher and inner panel making a slapping noise 2 Inside handle escutcheon connection to door finisher 3 Wiring harnesses tapping 4 Door striker out of alignment causing a popping noise on starts and stops Tapping moving the components or pressing on them while driving to duplicate the conditions can isolate many of these incidents The areas can usually be insulated with felt cloth tape or insulator foam blocks from the NISSAN Squeak and Rattle Kit J 43980 to repair the noise TRUNK Trunk noises are often caused by a loose jack or loose items put into the trunk by the customer In addition check for the following items Revision 2010 May INT 9 2011 QX56 SQUEAK AND RATTLE TROUBLE DIAGNOSES SYMPTOM DIAGNOSIS 1 Trunk lid dumpers out of adjustment 2 Trunk lid striker out of adjustment 3 Trunk lid torsion bars knocking together 4 Aloose license plate or bracket Most of these inciden
27. ient clearance between components Separate components by repositioning or loosening and retightening the components if possible Insulate components with a suitable insulator such as urethane pads foam blocks felt cloth tape or ure thane tape A NISSAN Squeak and Rattle Kit J 43980 is available through the authorized NISSAN Parts Department CAUTION Never use excessive force as many components are constructed of plastic and may be damaged NOTE Always check with the Parts Department for the latest parts information The following materials are contained in the NISSAN Squeak and Rattle Kit J 43980 Each item can be ordered separately as needed URETHANE PADS 1 5 mm 0 059 in thick Insulates connectors harness etc 76268 9E005 100 x 135 mm 3 937 x 5 315 in 76884 71L01 60 x 85 mm 2 362 x 3 346 in 76884 71L02 15 x 25 mm 0 591 x 0 984 in INSULATOR Foam blocks Insulates components from contact Can be used to fill space behind a panel 73982 9E000 45 mm 1 772 in thick 50 x 50 mm 1 969 x 1 969 in 73982 50Y00 10 mm 0 394 in thick 50 x 50 mm 1 969 x 1 969 in INSULATOR Light foam block 80845 71L00 30 mm 1 18 in thick 30 x 50 mm 1 181 x 1 969in FELT CLOTHTAPE Revision 2010 May INT 8 2011 QX56 SQUEAK AND RATTLE TROUBLE DIAGNOSES SYMPTOM DIAGNOSIS gt Used to insulate where movement does not occur Ideal for instrument panel applications 68370 4B000 15 x 25 mm 0 591 x
28. ing a remover tool A and then remove back pillar garnish LON VAN A aN Ex JMJIA4045ZZ Revision 2010 May INT 37 2011 QX56 LUGGAGE FLOOR TRIM REMOVAL AND INSTALLATION gt INSTALLATION Note the following items and install in the reverse order of removal CAUTION Visually check the clips and pawl for deformation and damage during installation Replace with new ones if necessary When installing back pillar garnish check that clips and pawl are securely fitted in body panel holes and press them in LUGGAGE SIDE UPPER FINISHER LUGGAGE SIDE UPPER FINISHER Removal and Installation Gre REMOVAL 1 Remove luggage side lower finisher Refer to INT 36 LUGGAGE SIDE LOWER FINISHER Removal and Installation 2 Remove rear pillar finisher Refer to INT 37 REAR PILLAR FINISHER Removal and Installation Remove back pillar garnish Refer to INT 37 BACK PILLAR GARNISH Removal and Installation 4 Remove luggage side upper finisher 1 Remove mounting bolts 1 2 Disengage luggage side upper finisher 2 fixing clips using a remover tool A and then remove luggage side upper fin isher 3 w JMJIA4046ZZ INSTALLATION Note the following items and install in the reverse order of removal CAUTION e Visually check the clips for deformation and damage during installation Replace with new ones if necessary e When installing luggage side upper finisher check that clips are s
29. ining switch C3 Clip Zx lt Pawl Reclining switch 22 is also installed on luggage side lower finisher LH 3 LUGGAGE FLOOR REAR BOARD LUGGAGE FLOOR REAR BOARD Removal and Installation EE REMOVAL 1 Open luggage floor board center 1 2 Remove both bolts shown by the arrows in the figure and then remove luggage floor board center fg JMJIA4027ZZ 3 dee luggage floor finishers LH RH Remove bolts shown by the arrows in the figure 2 Disengage luggage floor finisher 1 fixing pawl and clip using a remover tool A and then remove luggage side fin isher JMJIA4028ZZ 4 Remove both luggage floor rear boards 1 Fold down the third seat forward 2 Remove rope hook 1 mounting bolt using a socket wrench A and then remove rope hook JMJIA4029ZZ Revision 2010 May INT 34 2011 QX56 LUGGAGE FLOOR TRIM REMOVAL AND INSTALLATION gt 3 Disengage luggage floor board RH 1 fixing pawls and clips and then remove luggage side finisher 4 Disengage luggage floor board LH 2 fixing pawls and clips and then remove luggage side finisher LON VAN JMJIA4030ZZ INSTALLATION Note the following items and install in the reverse order of removal CAUTION Visually check the clips and pawls for deformation and damage during installation Replace with new ones if necessary e When installing luggage floor rear board check that clips and pawls are securely fitted in body panel holes a
30. ion of the system For removal of Spiral Cable and Air Bag Module see the SRS AIR BAG Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this Service Manual SRS wiring harnesses can be identified by yellow and or orange harnesses or har ness connectors PRECAUTIONS WHEN USING POWER TOOLS AIR OR ELECTRIC AND HAMMERS WARNING e When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the ignition ON or engine running DO NOT use air or electric power tools or strike near the sensor s with a hammer Heavy vibration could activate the sensor s and deploy the air bag s possibly causing serious injury When using air or electric power tools or hammers always switch the ignition OFF disconnect the ite battery and wait at least 3 minutes before performing any service Precaution Necessary for Steering Wheel Rotation after Battery Disconnect INFOID 00000000064 15652 NOTE Before removing and installing any control units first turn the push button ignition switch to the LOCK posi tion then disconnect both battery cables After finishing work confirm that all control unit connectors are connected properly then re connect both battery cables Always use CONSULT III to perform self diagnosis as a part of each function inspection after finishing work If a DTC is detected perform trouble diagnosis according to self diagnosis results For vehic
31. items and install in the reverse order of removal CAUTION Visually check the clips pawls and metal clip for deformation and damage during installation Replace with new ones if necessary When installing front door finisher check that clips pawls and metal clip are securely fitted in body panel holes and press them in Revision 2010 May INT 15 2011 QX56 REAR DOOR FINISHER REMOVAL AND INSTALLATION gt HEAR DOOR FINISHER Exploded View SEC 251 267 805 825 828 1 Rear door finisher 2 Bumper rubber 3 4 Inside handle escutcheon 5 Rear door grip cap 6 7 Power window switch finisher 8 Power window switch 9 10 Rear door garnish 11 Rear door tweeter 12 13 Rear door inside handle 14 Rear door inside seal E Clip N Pawl Removal and Installation CAUTION e When removing always use a remover tool that is made of plastic Never damage the body Revision 2010 May INT 16 INFOID 0000000006220243 JMJIA4423ZZ Door finisher cap Step lamp Tweeter grille Rear door panel INFOID 0000000006220244 2011 QX56 REAR DOOR FINISHER REMOVAL AND INSTALLATION REMOVAL 1 Fully open door window 2 Remove door finisher cap 1 using a small flat bladed screw driver A as shown by the arrow in the figure and then remove rear door finisher mounting bolt CAUTION Use a small flat bladed screwdriver wrapped in tape B Pawl LAPE 3 Insert a remover tool A between
32. late inner LH and RH Refer to INT 20 KICKING PLATE INNER Removal and Installation 5 Remove dash side finisher LH and RH Refer to INT 18 DASH SIDE FINISHER Removal and Installa tion 6 Remove center pillar lower garnish LH and RH Refer to INT 22 CENTER PILLAR LOWER GARNISH Removal and Installation 7 Remove instrument lower panel LH Refer to IP 14 Removal and Installation 8 Remove center console assembly Refer to P 25 Removal and Installation 9 Remove adjusting nut and front cable mounting bolts and nuts and then remove front cable Refer to TM 176 Removal and Installation Revision 2010 May INT 25 2011 QX56 FLOOR TRIM REMOVAL AND INSTALLATION gt 10 Remove the following parts after removing the center console assembly JMJIA4226ZZ Remove ground bolt G Disconnect floor harness connectors A and E Disconnect yaw rate side decel G sensor harness connector C Refer to BRC 138 Exploded View Disconnect diagnosis sensor unit harness connector D Refer to SR 26 Exploded View Remove floor harness clamps B and F 11 Remove A T shift selector assembly mounting bolts Refer to TM 176 Removal and Installation 12 Remove floor duct 1 LH and RH Refer to VTL 11 FLOOR DUCT 1 Removal and Installation 13 Disconnect drain hose 1 and remove instrument stay mounting nuts A and then remove instrument stay 2 LH and
33. le with steering lock unit if the battery is disconnected or discharged the steering wheel will lock and cannot be turned If turning the steering wheel is required with the battery disconnected or discharged follow the operation pro cedure below before starting the repair operation OPERATION PROCEDURE 1 Connect both battery cables NOTE Supply power using jumper cables if battery is discharged 2 Turn the push button ignition switch to ACC position At this time the steering lock will be released 3 Disconnect both battery cables The steering lock will remain released with both battery cables discon nected and the steering wheel can be turned 4 Perform the necessary repair operation Revision 2010 May INT 3 2011 QX56 PRECAUTIONS PRECAUTION gt 5 When the repair work is completed re connect both battery cables With the brake pedal released turn the push button ignition switch from ACC position to ON position then to LOCK position The steering wheel will lock when the push button ignition switch is turned to LOCK position 6 Perform self diagnosis check of all control units using CONSULT III Precaution for Procedure without Cowl Top Cover INFOID O000000006415651 When performing the procedure after removing cowl top cover cover the lower end of windshield with urethane etc PIIB3706J Precaution for Work INFOID 0000000006415642 After removing and installing the opening closing parts be
34. nd press them in LUGGAGE REAR PLATE LUGGAGE REAR PLATE Removal and Installation INFOID 0000000008220280 REMOVAL 1 Open luggage floor board center 2 Remove luggage floor finishers LH and RH 1 Remove nuts shown by the arrows in the figure 2 Disengage luggage floor finisher 1 fixing clip and pawl using a remover tool A and then remove luggage side fin isher 3 Disengage luggage rear plate 1 fixing clips and pawls using a remover tool A and then remove luggage rear plate LON E e LA JMJIA4041ZZ 4 Remove luggage rear plate mask from luggage rear plate INSTALLATION Note the following items and install in the reverse order of removal CAUTION e Visually check the clips and pawls for deformation and damage during installation Replace with new ones if necessary When installing luggage rear plate check that clips and pawls are securely fitted in body panel holes and press them in Revision 2010 May INT 35 2011 QX56 LUGGAGE FLOOR TRIM REMOVAL AND INSTALLATION gt LUGGAGE SIDE LOWER FINISHER LUGGAGE SIDE LOWER FINISHER Removal and Installation INFOID 0000000006220261 REMOVAL 1 Liftup the seat base tilt seatback forward and fold down second seat forward 2 Remove second seat belt anchor Refer to SB 13 SEAT BELT RETRACTOR Removal and Installation 3 Remove third seat Refer to SE 138 Removal and Installation 4 Remove third seat belt anchor Refer to SB 1
35. rear door grip cap 1 and rear door grip to disengage rear door grip cap fixing pawls as shown by the arrow in the figure and then remove fixing screws X Pawl x 4 Remove step lamp and then disconnect step lamp harness connector Refer to INL 74 Hemoval and Installation 5 Remove bumper rubber 6 Insert a remover tool A between rear door finisher and rear door panel to disengage the clips as shown by the arrow in the figure T Clip CAUTION Insert a remover tool into the part shown in the figure between the clips and the door panel Disconnect mood lamp harness connector Disconnect power window switch harness connector and clamp Disconnect lock knob cable and inside handle cable from rear inside handle 0 Remove rear door finisher from rear door panel 1 Remove the following parts after removing rear door finisher Mood lamp Power window switch Refer to PWC 74 Removal and Installation Rear door inside handle Refer to DLK 244 INSIDE HANDLE Removal and Installation Rear door tweeter Refer to AV 218 Removal and Installation INSTALLATION Note the following items and install in the reverse order of removal CAUTION e Visualy check the clips and pawls for deformation and damage during installation Replace with new ones if necessary When installing rear door finisher check that clips and pawls are securely fitted in body panel holes and press them in c LOO ON
36. reuse center pillar upper garnish Visually check the clip and pawl for deformation and damage during installation Replace with new ones if necessary e When installing center pillar upper garnish check that clip and pawl are securely fitted in body panel holes and press them in Revision 2010 May INT 23 2011 QX56 FLOOR TRIM REMOVAL AND INSTALLATION gt FLOOR TRIM Ex p lod ed V i ew INFOID 0000000006220253 FOR SECOND BENCH SEAT JMJIA4007ZZ 1 Front floor carpet 2 Carpet hook 3 Fixing clip 4 Footrest 5 Frontfloor spacer front 6 Front floor spacer rear 7 Floor hook 8 Rear floor carpet 9 Dual lock fastener Pawl lt a Vehicle front Revision 2010 May INT 24 2011 QX56 FLOOR TRIM REMOVAL AND INSTALLATION gt FOR SECOND CAPTAIN SEAT JMJIA4008ZZ 1 Front floor carpet 2 Carpet hook 3 Fixing clip 4 Footrest 5 Frontfloor spacer front 6 Front floor spacer rear 7 Floor hook 8 Rear floor carpet 9 Duallock fastener Pawl a Vehicle front FRONT FLOOR CARPET FRONT FLOOR CARPET Removal and Installation INFOID 0000000006220254 REMOVAL 1 Remove front seat assembly driver and passenger Refer to SE 112 Removal and Installation 2 Remove second seat assembly LH and RH Refer to SE 125 Removal and Installation 3 Remove floor grille LH and RH Refer to VTL 12 REAR FLOOR GRILLE Removal and Installation 4 Remove front kicking plate inner and rear kicking p
37. talling dash side finisher check that clips are securely fitted in body panel holes and press clips in FRONT PILLAR GARNISH FRONT PILLAR GARNISH Removal and Installation INFOID 0000000006220247 CAUTION e When removing always use a remover tool that is made of plastic Never damage the body REMOVAL 1 Release front pillar garnish portion of front body side welt 2 Disengage assist grip cap 1 fixing pawls using a flat bladed screwdriver A as shown in the figure and then remove assist grip mounting bolts and assist grip 2 CAUTION Apply protective tape B to the assist grip to protect from damage AJ Pawl E 3 Disengage front pillar garnish 1 fixing clip and metal clip using a remover tool A as shown by the arrow in the figure and then remove front pillar garnish 1 Metal clip JMJIA4019ZZ INSTALLATION Note the following items and install in the reverse order of removal CAUTION e Visually check the clip pawls and metal clip for deformation and damage during installation Replace with new ones if necessary When installing front pillar garnish check that clip and metal clip are securely fitted in body panel holes and press them in Revision 2010 May INT 19 2011 QX56 BODY SIDE TRIM REMOVAL AND INSTALLATION gt BODY SIDE WELT BODY SIDE WELT Removal and Installation INFOID 0000000006220246 CAUTION Never damage the body REMOVAL Front body side welt 1 Remove
38. tomer LI O Noise verified on test drive LI LI Noise source located and repaired LI O Follow up test drive performed to confirm repair LI LI VIN J Customer Name WOR Date This form must be attached to Work Order PIIB8742bE Revision 2010 May INT 12 2011 QX56 FRONT DOOR FINISHER REMOVAL AND INSTALLATION gt REMOVAL AND INSTALLATION FRONT DOOR FINISHER Ex p lod ed V i ew INFOID 0000000006220241 SEC 809 826 828 829 JMJIA4235ZZ 1 Front door panel 2 Front inside door seal 3 Front door finisher Bumper rubber 5 Door finisher cap 6 Inside handle escutcheon Front door grip cap 8 Steplamp 9 Power window switch finisher 10 Power window switch 11 Door mirror corner cover 12 BSW BSI indicator 18 Seat memory switch 14 Front door inside handle D Clip Pawl 1 1 Metalclip Revision 2010 May INT 13 2011 QX56 FRONT DOOR FINISHER REMOVAL AND INSTALLATION gt He m oval an d n stal lat i on INFOID 0000000006220242 CAUTION e When removing always use a remover tool that is made of plastic Never damage the body REMOVAL 1 Fully open door window 2 Remove door finisher cap 1 using a small flat bladed screw driver A as shown by the arrow in the figure and then remove front door finisher mounting bolt CAUTION Use a small flat bladed screwdriver wrapped in tape B AN Pawl L a 3 Insert a remover tool A between front door grip cap 1 and front door grip to
39. ts can be repaired by adjusting securing or insulating the item s or component s caus ing the noise SUNROOF HEADLINING Noises in the sunroof headlining area can often be traced to one of the following items 1 Sunroof lid rail linkage or seals making a rattle or light knocking noise 2 Sunvisor shaft shaking in the holder 3 Front or rear windshield touching headlining and squeaking Again pressing on the components to stop the noise while duplicating the conditions can isolate most of these incidents Repairs usually consist of insulating with felt cloth tape SEATS When isolating seat noise it is important to note the position the seat is in and the load placed on the seat when the noise occurs These conditions should be duplicated when verifying and isolating the cause of the noise Causes of seat noise include 1 Headrest rods and holder 2 Asqueak between the seat pad cushion and frame 3 The rear seatback lock and bracket These noises can be isolated by moving or pressing on the suspected components while duplicating the con ditions under which the noise occurs Most of these incidents can be repaired by repositioning the component or applying urethane tape to the contact area UNDERHOOD Some interior noise may be caused by components under the hood or on the engine wall The noise is then transmitted into the passenger compartment Causes of transmitted underhood noise include Any component mounted to the engine wall
40. wn by the arrow in the figure and then remove rear kick ing plate outer 1 CAUTION Apply protective tape B to the body panel to protect from dam age Pawl 0 48 JMJIA4024ZZ INSTALLATION Note the following items and then install in the reverse order of removal Revision 2010 May INT 21 2011 QX56 BODY SIDE TRIM REMOVAL AND INSTALLATION gt CAUTION e Visually check the pawls for deformation and damage during installation Replace with new ones if necessary When installing front kicking plate outer and rear kicking plate outer check that pawls are securely fitted in body panel holes and press them in CENTER PILLAR LOWER GARNISH CENTER PILLAR LOWER GARNISH Removal and Installation m CAUTION Never damage the body REMOVAL 1 Remove front kicking plate inner and rear kicking plate inner Refer to INT 20 KICKING PLATE INNER Removal and Installation Slide front seat assembly to the frontmost position Remove seat belt outer anchor Refer to SB 6 SEAT BELT RETRACTOR Removal and Installation Disengage center pillar lower garnish fixing clips Remove center pillar lower garnish according to the order of the arrows shown in the figure IAN INSTALLATION Note the following items and install in the reverse order of removal CAUTION Visually check the clips for deformation and damage during installation Replace with new ones if necessary When installing center
Download Pdf Manuals
Related Search