Service Manual LEVO Combi / Combi Junior
Contents
1. 11 8 Replacing the connector of the back low shearing system As a standard a connector of medium size is fixed The shearing range regarding the back movement is 9 cm 3 5 The replacement of this connecting piece using a shorter or a longer piece causes a variation of 8 cm 3 respectively 10 cm 4 of the shearing range Raise the seat to its maximum upright standing position Switch off the joystick module Loosen the fillister head screw at the backrest tube as well as the double head screw at the seat plate using a 4 mm hexagon key Remove the mentioned screws the washers and the connector First mount the upper end of the new connector at the backrest tube Make sure to put the two washers back in place After that mount the lower end of the new connector at the seat plate using the corresponding punched hole A on picture 6 and 7 Again make sure to put the two washers back in place 14 11 9 Replacing the driving motor when removing the driving motor the wheelchair must be unoccupied The wheelchair must be secured so that it cannot fall over or move while replacing the driving motor Take out the main fuse like described in 12 Open the cover of the battery box and disconnect the motor plug A from the power module Remove first the drive wheel as described in sector 8 1 Remove the motor cover loosening the screws using a4 mm hexagon key Loosen the motor disengaging lever cable Now loosen2. situations To perform a smoother start and stop of the on slopes we have optimized the motor compensation value Now the user of the chair will experience nearly no rollback when coming to a full stop or when starting to drive on a slope Service Instructions The new programs can be downloaded from the secured Login section of the LEVO website www levo ch F r Ein Conti Towle View Help DW 7 I 4 RM 4 B b Ferner DO Foie Fangar te BR ranson how 7 SW sem st Maren torrent ces ws 1030 ws Mren Fort Speed DS gt 03 Name Free gem x 5 Merwe A end ts rn kS nt _ Maan Turing Gee ie ms _ Mewar Tag Speed 71 123 Mean fares ACcelesston 12 Mewes forvwt Acorn ID 20 3 mar Frasi Decosnton Bg 2 Merwe Forveri Decelesbor t 20 Marmor Reverse Armen tt 16 2 Mew Reverse rin 5 te t Mame henw e min Po w Maa Rasane Cte aaecniene 10 x kd _ Maua Tun Acoslemton 10 x Ww Mrs Ta hati 3 13 gt Mour Tum Cao is 3 n Mewum laum Dare to 2 S rn 108 u Tome w5 gt 04 Tee Omen E ja s far Rabe An 5 TO wem H utei SO zm se Darter drer 6 General repair instruction Only a LEVO agent or their authorized dealers should carry out servicing and repairs to the LEVO combi Repairs For advice in all repairs in Switzerland contact LEVO AG Switzerland For all other countries contact your local LEVO agent Addresses are given at the front of this service manual or on the homepag
3. LEVO combi combi JR SERVICE MANUAL This manual is for use by LEVO AG agents or their authorized dealers Read these instructions before servicing the wheelchair This service manual must be read in conjunction with the user manual Alterations in constructional and technical manner or to the electronic require the written authorisation of LEVO AG otherwise no warranty or product liability will be accepted Version 1 2 Inhalt 1 PERO GUICTION sn sn b s a a ee ee 3 2 DISIA ae ee ee 3 2 1 Areas which has to be disinfeCted s sesreresrerrsrerrrrerrrrrrr rr rr rr rr RR KRK nenn nun nenn 3 2 2 PEOC a RN Eee Een 3 3 EA SS CV tre osar syran en ee a ee ELENA 4 4 AU USE ET Eee Eee 4 4 1 DEAL ODE th ee ee ee ee ere ee E er eT 4 4 2 Low Shearing at the back siossssesssrssesrerrrrerr rr esk rr rr r KRKA KRKA KR KKR KRA RR KKR KRK RR KRK RAA 4 4 3 Adjustment of the backrest ssnsissssssssessssrsrssrererrerrrr rer rr rr RR KRK RR KR RR RR RR KRK RR KR KRA DR 4 D Electronic control system isss 5 5 1 Programming R Net and VR2 zsssssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnennnnnnnnen 5 6 General repair instruction ana ann 7 Z TOOS T rGUS a een 7 8 ENDOranNE IN TOTT TG a 0 RT 7 9 Recommended safety Checks 8 EO CIS aI WING RN ER HR 9 De NRO DOIN S kassa eases E A E E enseresr eee 10 11 1 Replacing the drive wheels stnosessssessssrererrerrrrnrrrrrr rr rr ARR KRK KKR RR ARR KKR RR KKR KRK KR RR RA 10 11 2 Replacing the tir
4. R RR RA 21 11 19 Replacing the actuator lying ossssssesiesesrerrsrerrrrerrrrrrr nr rr nennen RAK RR RR KRK RR nn nn nun 22 11 20 Replacing the legrest aCtUatOr srrresraresrrrrrrerrrrnrrrr rr rr rr KR KRK RR KRK RA 22 11 21 Replacing of lights and indicators srssmssssssssrsrsrrrrerrrrrrr rer rr KRKA KRK RR KRK RR KRK RR KKR 23 11 27 FONC EGNU rata ssd tiden NR SR 23 11 23 Back Ge a eek 23 11 24 MA NO a ee ne een 24 e M ee A E EA ee ae 24 13 Testing the wheelchair nern 24 14 VELSI00 MoaDagement seen 25 1 Introduction Apart from regular charging of the batteries and keeping the wheelchair clean the LEVO combi is maintenance free and no attention is required by the user Because of the complexity of the wheelchair the LEVO agent or authorized dealer should carry out a safety check at least once per year This service manual is to be used by the LEVO agent or authorized dealer The manual gives information on how to perform a safety check and carry out repairs to the LEVO combi This manual provides a good service to the persons in charge of the maintenance of the LEVO combi And of course the user appreciates the safety and the reliability of a well maintained wheelchair This manual must always be read and used with the user manual 2 Disinfecting Before carrying out any service work it is advisable to disinfect Use for disinfecting ready alcohol spray which are suitable for whole areas e g Germex spray the co
5. and seat tilt lying to standing directly Repair any fault found e Check all lights and indications Replace components with failures e Use all functions and drive the wheelchair as a final check In case you notice any kind of problems arrange the fixing 10 Cleaning Before returning the wheelchair to the customer ensure the wheelchair is clean and well presented e If there is any dirt it should be cleaned off using a damp cloth and then dried thoroughly e For more stubborn stains wipe with a damp cloth using a mild solution of warm water and soap e Never use furniture polish or any fluids containing alcohol to clean the frame e In case of dirt on the seat cushion cover or the back rest cover you can remove both of it and wash it softly Do not wash it warmer than 40 degree Celsius 11 Repairs Note the mandatory items listed in the Instruction Manual before replacing components 11 1 Replacing the drive wheels when removing a wheel the wheelchair must be unoccupied The wheelchair must be supported B so that it neither falls over or moves when a wheel is removed e Pull off the protective end cap which covers the countersunk screw e Remove the countersunk screw A using a 5 mm hexagon key e Remove then the black washer F picture 2 e Withdraw the wheel from the wheelchair e To mount the new wheels follow the instructions in the reverse order 11 2 Replacing the tire of a drive wheel When replaci
6. d as a complete set 11 11 Battery Wiring The figure shows the correctly wiring of the batteries 16 11 12 Replacing the Joystick module R Net e Switch off the joystick module e Unplug the joystick cable at the back of the joystick module e Loosen the two hexagon screws A at the back of the joystick module using a 2 5 mm hexagon key and remove them e Lift the Joystick module e Mount the new joystick module in the reverse order 11 13 Replacing the power module R Net e Raise the seat to its maximum upright Standing position e Take out the fuse e Open the cover of the battery box e Loosen the 4 screws that hold the limit switch plate and remove the plate e Cut the cable ties e Lift the power module that you get access to the front of the power module e Unplug the following cables from the power module ISM cable A left motor cable B battery cable C right motor cable D limit switch cable E limit switch cable F all cables are listed from the left to the right hand side see picture 14 17 11 14 Control box e Ziehen Sie die folgenden Kabel aus dem Power Modul heraus ISM Kabel A linkes Motorkabel B Batteriekabel C rot schwarz oder rot blau rechtes Motorkabel D Endschalter Kabel E Endschalter Kabel F Genannt von links nach rechts siehe Abbildung 14 Note that the connectors are locked with plug in fuses e Motor connector Press the latches on the up
7. dealer For information consult the user instruction manual at section 7 5 4 3 Adjustment of the backrest The adjustment of the backrest should only be done by the LEVO agent or authorised dealer For information consult the user instruction manual at section 7 6 and 7 7 5 Electronic control system The preset settings are chosen to ensure safe operation The settings are in compliance with all relevant legal requirements regarding the entire operating range of the joystick and the speed control In case the preset settings don t meet the needs of the user the control system can be programmed individually the maximum speed might be decreased for example Warning Programming should only be conducted by healthcare professionals with in depth knowledge of Penny amp Giles electronic control systems Incorrect programming could result in an unsafe set up of a wheelchair for the user LEVO AG accepts no liability for losses of any kind if the drive or stability characteristics of the wheelchair are altered without prior notification and discussion with LEVO AG It is in the responsibility of the person programming the control system to make sure that the stopping distance requirement specified for the country in which the wheelchair will be used is satisfied If the braking rate is low the forward and reverse maximum speed settings may need to be re programmed It is in the responsibility of the person programming the control system to make s
8. e of a drive wheel zeeeeeneennnnnnnnnnnnnnn nr rr nun RAK nn nun nenn KKR KRK RNA 10 11 3 Replacing the front wheels sosnccsssssssesrrssrer rskr rnr esk nn nn nun RAKA nn nn nn KRK RR KKR KRK RNA 11 11 4 Replacing the back WNEEl sisnssssssrsresrsresrererrnrrrrrrr rr rr nn nun nennen RAR R RR RR KKR KRK KR RR RA 11 11 5 Replacing the gas spring of the rear wheel snrsmssssssssesrerrsrerrrrrr rer rr rn rer rr rn rens 12 11 6 Replacing the wheel fork front and rear sssssssssssreresrerrrrerrrr rskr rer nun nenn ann nn 13 11 7 Replacing of the rear fork uusssssnnnnnnnnnnnnnn nn nun nun nun nun RR KRK RR RAK RR RR RR RR KRK RR RR RA 13 11 8 Replacing the connector of the back low shearing SYSteM s sssresrsrerrerera 14 11 9 Replacing the driving Molterer RR RR KRK RR KKR KRK RNA 15 11 10 Replacing the batteries as a RR KKR RR KR RA 16 11 27 AL yy FING ee ee 16 11 12 Replacing the Joystick Module R Net ssssrossssssrssesrsrrssrerrsrrr ers non nun nn nn nun nn nn 17 11 13 Replacing the power module R Net zuusssssnnnnnnnnnnnnnnnnnnnnnn rr KRK RR KRK KRK RA 17 11 12 CINE Ol D M ae GR EAEE EET 18 1115 IM BO ER EEE 18 11 16 Replacing the gas spring 000asisss nun non nun nn En nun KKR RR KKR KRK nn nun nenn nun nenne 19 11 17 Replacing the actuator standing zzzssseessnnnnnnnnnnnnnnnn nennen nn nun nn nun nn nn 20 11 18 Replacing the actuator Lift sisssosssssssesesserrsrasrrrrerrrrr rr r nn rr KRK RAK nun nun KRK K
9. e www levo ch Major repairs For all major repairs e g bent or damaged frame always replace complete components Never try to repair damaged steel work or components Replacement parts Factory replacement components should be used in all repairs these are available from LEVO AG To order parts see the parts list drawings and the correlative list both available at LEVO AG Locknuts must never be reused but must be replaced by new ones e Secure each screw connection against inadvertent release Use lock nuts or screw securing adhesive medium strength e Repairs to engines and electronic components must only be performed by the LEVO 7 Tools amp torque settings The following tools are required to service the wheelchair Spanners and sockets 8 mm through to 24 mm Hexagon key 2 mm through to 8 mm Screwdrivers 1 Nm through to 50 Nm Phillips head screwdriver and slotted screwdriver Soft headed hammer Snap through tool Torque settings 8 Important information Do not reuse nuts Always replace with a new nut Always use thread locking compound Always use recommended components and parts available from LEVO AG Do not modify or repair the frame LEVO AG is responsible for any repairs on gas springs motors and electronic parts 9 Recommended safety checks The following safety checks should be carried out at least once per year This should be done by a LEVO agent or authorized dealer If a fault is found do
10. ever out and turn it simultaneously to the ON position to activate the motor brakes The power wheel should be blocked now In case the power wheels are not completely blocked it is absolutely necessary to replace the motor e Check the powered function of the motor disengaging lever Switch on the joystick module and start driving forwards Let of the joystick As a reaction the wheelchair Should stop and the solenoid brakes of the motor should snap in evidence Repeat this check driving backwards and to each side In case the motor brakes dont function correctly check the battery indicator on the joystick module for any failure indication Consult the controller self help guide user manual sector 23 for details about failure indications e Make sure all the connectors are properly inserted that the brake solenoids are energized and that the solenoid coil is not open or short circuited by testing the two bigger pins on the motor lead plug If necessary replace the motor e Check all electrical cables and wires for chafing and clamp spots Replace if necessary e Check all electrical connectors for corrosion and security Replace if necessary e Clean the batteries and terminals Test the battery capacity and advise the customer of their condition Charge the batteries before returning the wheelchair to the customer e Check all MODE functions as standing up and sitting as well as the optionally added functions lift backrest reclining
11. he bottom rail of the yoke A with a block of wood B wooden stick or similar so that the elevator cannot fall down See Figure 18a e Unplug the actuator from the ISM controller e Remove the spring clip A Figure 17 at the upper end of the actuator e Take the locking pin B Figure 17 out respectively beat him with a punch tool and the hammer pressing gently out e Loosen the actuator at the upper end of the holder of the actuator lift e Remove the spring clip at the lower end of the actuator Remove the cotter pins as described above See figure 17 e Install the new actuator as described in the reverse order Make sure that the piston rod of the new actuator is retracted Start with the lower end of the actuator by plugging the actuator in the battery box Take out the piston rod of the actuator until the actuator bracket for the lift fits in 21 11 19 Replacing the actuator lying Raise the seat to the upright standing position Switch off the joystick module and take out the fuse Disconnect the plug of the actuator lying from the battery box Loosen the screw A on picture 19 using a 8 mm flat wrench e Remove the back end of the actuator from the connecting part Remove the clip A on picture 17 at the front end of the actuator Press out the spike B on picture 17 respectively use a hammer and a snap through tool to strike the spike carefully out of the rod Press
12. heelchair when repairs have been completed and before it is returned to the customer Only return the wheelchair to the client when all faults have been rectified 24 14Version Management Version No Date Description 2012 07 30 First Edition Combi 923 2014 03 2010 Diverse adjustments H B gli 2014 06 02 T V Certification Update finalized H B gli ee Re a HE EN Fr a 25
13. ke sure all washers are placed correctly 11 11 5 Replacing the gas spring of the rear wheel e Lift the back wheel up with a clamping set e Remove the supporting handle notice e Loose the clamping set so that the gas springs are relieved e Remove the securing clips at both gas springs above and below with a screwdriver e Now you can take off the gas springs from the ball pin and exchange them e Install everything again in reverse order 12 11 6 Replacing the wheel fork front and rear when removing a wheel and or a wheel fork the wheelchair must be unoccupied The wheelchair must be supported so that it neither falls over nor moves when a wheel is removed e Loosen the hexagon spike A at the wheel fork axle as much as it needs to withdraw the fork from the mount Use a 24 mm hexagon key e Replace the wheel fork e Reassemble the used wheel in case it is still in a good condition Doing so please follow the instruction in sector 8 3 respectively 8 4 e Mount the new wheel fork in the reversed order Picture 3 shows all parts in details 11 7 Replacing of the rear fork Lift the rear wheel as described under 11 6 replacing the gas springs of the rear wheel Unscrew the rear fork from the sleeve of the rear bracket To do this with the wrench on the hexagon A see figure below The assembling of the rear wheel fork is done in analogy of the disassembling in the reverse order 13
14. mpany Pramol chemistry 2 1 Areas which has to be disinfected Armrest and Joystick Back upholstery Seat Legrest Footrest Knee support ins N Procedere Cover the Chassis with plastic films or the like as to protect them from corrosion Clean them Above components with a water hose or better with a water hose and a mild soap solution e Enter and leave the agent at least one minutes affect the above components with a disinfectant spray e Do not dry completely the components 3 Health amp safety Accidents do occur When working on or testing the wheelchair be aware of the dangers and take care to ensure your own and other peoples health and safety Please note all regulations and rules about safety in electronics and mechanics 4 Adjustments The majority of the adjustments can be carried out by the user or his family and are covered in the instruction manual However the LEVO agent should always on delivery adjust the wheelchair to suit the user The body related settings of your LEVO combi are to be adapted precisely to the needs of the patient Improper settings can cause serious physical injury to the user 4 1 Seat depth The adjustment of the seat depth should only be done by the LEVO agent or authorised dealer For information consult the user instruction manual at section 7 1 4 2 Low shearing at the back The adjustment of the low shearing at the back should only be done by the LEVO agent or authorised
15. ng the tire means removing a wheel the wheelchair must be unoccupied The wheelchair must be secured so that it cannot fall over or move when a wheel is removed e Remove the drive wheel as described in sector 8 1 e Remove the four black countersunk screws G to take the flange of the wheel using a 5 mm hexagon key Remove five screws H of the rim using a 6mm hexagon key Withdraw the rims B1 and B2 from the tire A Reassemble in reverse order To fit the rims to the tire use gunk to make it easier Important Take note of the circulation direction indicated on the tire before fixing 10 11 3 Replacing the front wheels When removing a wheel the wheelchair must be unoccupied The wheelchair must be spoke so that it neither falls over nor moves when a wheel is removed e Pull off the protective end caps from the axle Loosen the hexagon screw and washer using a 13 mm hexagon key and remove the screw the Washer and the nut 1 1 Withdraw the wheel from the fork Reassemble the new wheel in reverse order Make sure all washers are placed correctly 11 4 Replacing the back wheel When removing the wheel the wheelchair must be unoccupied The wheelchair must be secured so that it cannot fall over or move when the wheel is removed e Loosen the screw 1 1 using a 6 mm hexagon key and remove the screw the washer and the nut Withdraw the back wheel from the fork Reassemble the new wheel in reverse order e Ma
16. not allow the wheelchair to be used until it has been corrected e Make sure that the backrest options and additional material is fixed safely Using a V Trak backrest system check the lever of the backrest All levers have to be completely pushed down Repair any fault found immediately e Examine the wheelchair frame for any damage Replace any damaged or faulty components e Examine the condition of the seat cushion and the backrest and replace if necessary e Examine condition of all harnesses straps and buckles and replace if necessary e Examine and operate the footrest mechanism Replace any damaged or faulty components e Examine nuts bolts pivots and frame plugs for tightness and general condition Replace any faulty components e Examine the rear wheel the front wheels and their castors for free rotation and security Optimize the rotation and repair any fault found e The tires are maintenance free besides occasional cleaning Use a damp cloth for cleaning Tires must get replaced when the tire s profile is worn down For more information please consult sector 8 1 to 8 4 e Check the free wheel device and the motor disengaging lever for correct operation Repair any fault found e Check the mechanical function of the motor disengaging lever Pull the motor disengaging lever out and turn it simultaneously to the OFF position At this stage it should be possible to push the wheelchair Pull the motor disengaging l
17. pectively out of the flexible hose Cut off the shrinked isolation Unplug the light respectively replace it with the new one Shrink respectively isolate the two connections Feed in the cable into the hose and fix the light at the support 11 23 Back Light x e Unplug the lightning cable inside respectively below the cover e Release the screws and nuts to take out the plate including the light e Take out the light from the plate and replace it by the new one e Assemble in the reverse order 23 11 24 Indicators Unplug the red cable socket Release the indicator by a wrench number 17 Loosen the nut which is mounted on at the inner side of the light support In case The plugs of the front indicators are in the spiral protection hose To find them you follow the cables beginning inside the indicator support the nut is too much tightened it will be necessary to use a second wrench to hold the counter nut outside of the light support e Replace the light by the new one and assemble in reversed order 12 Main fuse The main fuse housing is under the chair cover in the rear To get access carefully open the cover as shown Open the fuse cover insert one of the two fuses which are delivered in a separate plastic bag and snap the fuse cover back Store the fuse cabling properly above the batteries by the attached Velcro strap 13 Testing the wheelchair Main fuse Always perform full functional tests on the w
18. per side edges of the connector B D e Battery connector Press the snap closure on the top surface of the connector C e The power module is attached with Velcro at the bottom of the battery box so it does not slip while driving Lift the old power module from the battery box e Install the new power module as described above in reverse order 11 15 ISM Box The ISM box controls the lighting and the actuators This box can be expanded in the same way as the controller 18 11 16 Replacing the gas spring The gas spring serves for easy manual rising of the seat in case of any disorder considering of the batteries or the actuator standing and you still need access to the battery box in order of any repair The gas spring raises the seat and supports it in the standing position without the actuator standing in use Raise the seat to the maximum standing position Lift the clip B on the upper part of joint of the gas spring using a slotted screwdriver A and press the joint part off the joint pivot C Caution Do not remove the clip Lift the clip on the lower part of the joint of the gas spring using a slotted screwdriver and press the joint part off the joint pivot Caution Do not remove the clip Remove the gas spring now Mount the new gas spring in the reverse order pressing the ends on the correlative joint pivot 19 11 17 Replacing the actuator standing Raise the seat to the upright standing
19. position Switch off the joystick module and the safety cut out Remove the quick release axle A picture 16 from the upper end of the actuator Push the seat further to the upright position as high as it needs to remove the actuator off the recess drilled into the seat support In case the seat is already at the maximum standing position the gas spring has to be unfixed at the upper end Read the instruction in sector 8 13 Remove the clip A picture 17 at the inside of the lower end of the actuator Press out the spike B picture 17 use a hammer and a snap through tool to strike the spike carefully out of the rod Unplug the actuator from the battery box and remove it Reassemble the new actuator in the reverse order 20 11 18 Replacing the actuator Lift e Remove the main fuse from the battery and pull the side under the rear cover out Please refer to the information under 11 Assurance in the manual e If the chair is equipped with sun function move the seat to the reclining position and then pull the main fuse wheelchair de energized This gives you an ideal position of the leg supports for the replacement Is the LEVO combi not equipped with optional seat functions loosen the bolt lock washer connection C between the legrest and backrest construction and fold the legrest upward E see Figure 18b and 18c The bolt lock washer connection is near the cotter pin D of the standing actuator e Do you support t
20. the four cylinder head screws B at the motor using a 6 mm hexagon key Mount the new motor with the four cylinder head screws B using the 6 mm hexagon key again Fix the disengaging motor cable as described in sector 8 7 Reassemble the motor cover Mount the drive wheel in the reverse order Connect the motor plug to the power module Switch on the safety cut out 15 11 10 Replacing the batteries Caution The battery box is heavy take care when lifting and carrying Caution When working on the batteries take great care not to short out the terminals with any metal tools etc Always remove wristwatches or jewelry When reconnecting make sure all wires are connected to the correct battery terminals Caution Contact with acids is dangerous If you come into contact with acids rinse the contaminated body parts immediately with water and consult your doctor Take off immediately using acid contaminated clothing Caution Always wash your hands after working on the batteries e If possible raise the seat to the fully upright d A ol position eae wa e Switch off the safety cut out A e Open the battery cover Loosen the screws at the electrical contact of the batteries using a 13 mm screw wrench and remove the small metal terminal piece A e Lift the batteries out of the battery box e Putthe new batteries in the battery box e Reassemble in the reverse order The batteries should always be replace
21. the front end of the actuator down and off the bracket Pull it then to the front and off the back bracket e Now remove the actuator e Reassemble the new actuator lying in the reverse order e Take care that the piston rod of the new actuator is retracted inside Start work at the front part of the actuator and connect the plug of the actuator at the battery box first Retract the piston rod until it fits to the halter at the back 11 20 Replacing the legrest actuator e Remove the footrest as described in 11 3 Footplate in the instruction manual e Unplug the actuator C at the ISM control box e Remove the bolt connection at the points A and B and remove the actuator Install the new actuator as described above in reverse order Make sure that the piston rod of the new actuator is retracted Start with the lower end of the actuator by plugging the actuator in the battery box Take out the piston rod of the actuator until the actuator bracket for the lift fits 22 11 21 Replacing of lights and indicators Caution Always take out the fuse first before any part of the lighting system will be replaced or fixed Please be aware about all electronic safety regulation before you start changing any lighting components All lighting components may only be replaced as a whole Pic 120 Front Light 11 22 Front Light Release screw A Abb 120 e Pull carefully the front light cable out of the support res
22. ure that the settings are safe and to note any programming changes made 5 1 Programming R Net and VR2 The programming is done by dubbing the control software of a laptop or PC to the Controller of the wheelchair Laptop PC must be equipped with the appropriate PGDT software e Start the software on your laptop PC e Insert the read in between the cable ends of the control panel cable and the Controller the interface is located below the armrest e Connect via the USB interface the read in on the laptop PC e Transfer the program The drive programs are made to give the user more ease of use and even better drive characteristics All will be fitted with standard programs that provide the user with different Standard profiles programmed in the drive software The benefit for the user is that there is a more flexible way of speed and driving settings in the chair for both indoor and outdoor use Because multiple profiles per ordered speed setting are used you do not need to make the choice for the Standard Classic and Fun at the order form anymore Motor setting improvements To optimize the current through the motors when they are pushed to their limits we have improved some parameters in the motor settings section of the drive software Your benefits with these improvements are that the motors will be driven towards their limits in a less intense way which gives the motors a more durable and longer life during extreme
Download Pdf Manuals
Related Search