Sabina Comfort Model EM/ES
Contents
1. 4 To achieve a more upright position continue the lifting motion to the uppermost position The lifting procedure may seem unpleasant for those who are unaccustomed to it Remember that Sabina Comfort has two speeds For maximum comfort the mast must be locked into the base in the best possible of the three alternative holes See page 6 illustra tion 2 14 Liko www liko com 1 Place Sabina Comfort in front of the user and adjust the width of the undercarriage so that the feet can be placed centrally on the foot tray with the shins parallel to the lower leg supports Adjust lower leg support height and depth against the shins so as to achieve a comfortable resistance under the kneecap 3 Raise the lift about 10 20 cm 4 8 inch The user grasps the sling bar and the lifting procedure can continue If the user leans backwards during the lift this facilita tes lifting and prevents the vest from sliding up The height to which the user is to be lifted must be decided and tested in each individual case Make sure the vest s loops are correctly fastened when the straps are fully extended but before the user is clear of the seat Troubleshooting Sabina and Sabina Comfort The lift does not work up down Check that the emergency stop button Width adjustment does not work is not pushed in Check that the cables are connected correctly Check that the battery is charged Check that the batter2. The user is unable to rise to a sufficiently upright position What can be done Sometimes this is due to the user s physical status weak musculature poor tone and or contractures in hips and knee To use Sabina in the best possible way follow these steps 1 Hook the vest to the hook in the shorter loop B instead of the longer loop i 2 Raise the mast in Sabina s base See Adjustment lifting height above S 3 Try a smaller sized vest A smaller size means shorter distance to the hooks which results in a more upright standing position 10 Liko www liko com Sit to stand lifting with Sabina with the active participation of the user 1 Place Sabina in front of the user and adjust 2 Place the sit to stand vest around the the width of the undercarriage so that the feet user according to the instructions for that can be placed centrally on the foot tray with particular vest the shins parallel to the lower leg supports Adjust lower leg support height and depth against the shins so as to achieve a comforta ble resistance under the kneecap 3 Raise Sabina about 10 20 cm 4 8 inch The 4 To achieve a more upright position continue user grasps the crossbar and the lifting proce the lifting motion to the uppermost position dure can continue If the user leans backwards The lifting procedure may seem unpleasant during the lift this facilitates lifting and prevents for those who are unaccustomed to
3. Using Sabina and Sabina Comfort in lifting and sit to stand situations Accessories Different accessories are available for Sabina and Sabina Comfort Study the instructions for use of accessories carefully In most cases one of Liko s sit to stand vests is used We recommend the following combinations Sabina Liko SupportVest or Liko SupportVest for raising Sabina Comfort Liko ComfortVest To a limited extent Sabina and Sabina Comfort can be used for passive lifting of a user who is lifted in a sitting position in a sling An individual test is necessary We recommend one of the following sling models that does not restrict the lifting height For Sabina Liko Original Sling arms out Liko HygieneSling LikoStraps For Sabina Comfort Liko Universal Sling Liko Original Sling Study the instruction guides for the sling and check to ensure that the sling that is to be used matches the width of the sling bar In this case Sabina s sling bar is comparable to Liko Sling Bar Slim 350 and Sabina Comfort with Liko Sling Bar Wide 670 For Sabina Sabina Comfort a Side support is available see page 9 The Side support is intended for sit to stand lifting of users with limited lateral stability Adjustment lifting height Individual adjustment of lifting height Best position User s height Pos lt 170 cm lt 5 7 1 160 190 cm 5 3 6 3 2 gt 180 cm lt 6 Ft 3
4. Tr Min Max 7 max ue Del diameter Sabina 86 69 105 53 90 21 30 65 30 40 11 15 5 Gomi 86 69 105 53 90 21 30 65 30 40 11 15 5 Capacity and weight in kg Measurement in cm These measures depend on in which hole the mast is levelled and secured See assembly instructions page 6 11 cm is standard setting 15 cm is when using 100 mm wheel diameter Model Capacity Weight Turning Max Min Max AMin Tot Del diameter Sabina 34 26 42 21 36 8 12 6 2 13 8 98 5 6 34 26 42 21 36 8 12 26 12 16 46 2 236 98 5 Capacity and weight in lbs Measurement in inch These measures depend on in which hole the mast is levelled and secured See assembly instructions page 6 4 inches is standard setting 6 inches is when using 100 mm wheel diameter 5 Liko www liko com Assembly Instructions Before assembling check that you have the After assembling check the following following parts and tools Check that the lifting motion as well as the e Lift assembly and overhead beam width adjustment of the base coincides with e Base with motor for width adjustment the indicators on the hand control e Hand control with cable e Check that the emergency lowering device e Tools Wrench 17 2 functions properly e Connection cable for charging e Check the wheel brakes e Battery e Check the battery charge e Frame for the footrest and footrest e Check that the LED lamps o
5. manuals have been carefully studied and fully understood e persons using the equipment have received appropriate instructions and training all lift components material and seams are intact and show no signs of damage or wear that in each individual lifting situation you have selected the correct type size material and design of slings and accessories to safely meet the user s needs Never leave a user unsupervised in Sabina Sabina Comfort ce Sabina EM ES and Sabina Comfort EM ES are classified as a medical technical product Class I Sabina EM ES and Sabina Comfort EM ES comply with the requirements according to IEC 60601 1 Sabina EM ES and Sabina Comfort EM ES comply with the EMC requirements according to IEC 60601 1 2 Sabina EM ES and Sabina Comfort EM ES comply with the requirements according to EN ISO 10535 Radio transmitting devices mobile telephones etc should never be used near the lift since they can interfere with the function of the lift Particular care must be taken when using strong sources of potential disturbance such as diathermy etc so that cables are not positioned on or near the lift If you have questions please consult a biomedical engineer or the supplier A Maximum load 200 kg 440 Ibs 3 Liko www liko com Technical Specifications Batteries Two 12V 2 9 Ah valve regulated Footrest Removable leadacid batteries New batteries are Kneepad Height and width adjustable Removable
6. provided by the supplier Intermittent Int Op 10 90 active operation max 6 Motor mast 24 V 6 A manufacturer Linak operation min Out of a time of 100 active must permanent magnetic motor with be less than 10 however not more than 6 min mechanical safety mechanism and safety nut IP class 43 Motor base 24 V 3 5 A manufacturer Linak permanent magnetic motor Charger Built in charger 100 230 V 50 60 Hz 2 Built for indoor operation max 400 mA Type B according to the degree of protection Material Painted steel with laquer top coat against electric chock Emergency Mechanical pats pend and Class Il equipment Lowering electrical l Product Information 6 OG 8 2 9 4 6 5 Q D D B Positions 1 Lift assembly 9 Label 18 Sling Bar 2 Overhead beam 10 Motor height adjustment 19 Cross Bar Comfort only 3 Base 11 Motor base width adjustm 20 Emergency Stop 4 Batteries 12 Rear wheel with brake 21 Electrical emergency lowering raising 5 Hand control 13 Front wheel 22 Indicator lamp for charging Charge 6 El Power Pack with 14 Cable handcontrol 23 Indicator lamp for charging ON emergency stop 15 Emergency lowering 24 Locking handle 2 positions 7 Lift hook 16 Adjustable kneepad 8 Safety latch 17 Footrest detachable 4 Liko www liko com Dimensions Sabina EM ES Model Capacity E F Weight Turning
7. e Liko www liko com 7 Connect the extension cable for the charging cable to the control box 10 Mount the holder for the charging cable Hook it the outer edge and press down until you hear a Click 13 Place the brace for the kneepad into the bracket on the mast Use knob A to adjust the depth i e the distance to the user s knees Adjust the height of the kneepad e and turn knob B to lock the kneepad in place Tighten the knobs securely after making these adjustments Connect the cables as follows Mast motor cable to socket number 1 Base motor cable to socket number 2 not model EM Hand control cable to the socket farthest to the left on the electronic power pack number 3 in the diagram 9 Connect the charging cable to the extension cable 12 1 Place the footrest over the base of the mast as shown in the illustration Check to see that the brack ets are correctly aligned 2 Check to see that the plas tic footrest is pressed down and in a stable position over the foot rest frame User s Guide Maneuver Maneuver the lift using the pushbuttons on the hand control Directional arrows show the direction of move ment up down Bigger arrows means faster move ment The lift stoos when you release the buttons The base width is adjusted by pressing eithe
8. ectly fastened when the straps are fully extended but before the user is clear of the seat 12 Liko www liko com Passive lifting from a sitting position with Sabina or Sabina Comfort 1 Disassemble kneepad loosen screw A 2 Apply an appropriate sling see page 10 and pull it out Remove foot tray Grasp front Follow the instructions for that particular sling edge bend up and lift foot tray away from base 3 Move lift forward Hook sling loops to lift 4 Raise sling bar to the minimum height arm hooks Lower the lift arms if they are necessary to achieve the transfer too high A Make sure the vest s loops are A Do not lift the user so high that correctly fastened when the straps he se she comes too close to the lift mast are fully extended but before the user is clear of the seat A NOTE This method of lifting sitting users with Sabina or Sabina Comfort cannot replace regular routine lifting from the sitting position using conventional mobile lifts such as Uno or Golvo Instead it is intended as an occasional solution when the user cannot actively manage a sit to stand lift If the need for passive lifting from sitting persists we recommend the use of Uno or Golvo 13 Liko www liko com Sit to stand lifting with Sabina Comfort with the active participation of the user 2 Place the sit to stand vest around the user according to the instructions for that particular vest
9. ications Product Information 5 9 PAT TVS OVS aee ER ceea E O 6 7 E E E E EA E 8 14 16 E E r EE EE EEEE 8 PME VO Charging the batteries Accessories for Sabina and Sabina Comfort cccccccccceccesssecceeeceeeeseceeeeeaeeeeeeeeeeas 9 Using Sabina and Sabina Comfort in lifting and sit to stand situations ccccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeaeeeeeees 10 Sit to stand lifting with Sabina with the active participation Of the user ceeccceccsseeeeeeeeeeeeeeeeeeeseasaeeeeeeeeeas 11 Sit to stand lifting with Sabina and Side Support with the active participation of the user cccceeeeeeeeees 12 Passive lifting from a sitting position with Sabina or Sabina Comfort ccccccccessececsseeeceeeeeeceeeseeeeeesseeeeeeees 13 Sit to stand lifting with Sabina Comfort with the participation Of the user cccccceeeeeeeeeeeeeeeeeeeeesaeaeeeeeeeeeas 14 Troubleshooting Sabina and Sabina Comfort ccccccseccccecseeeeeeeeeeeeeeeeeeeeeeeeaeeeeeeseeeeeeeseas 15 Care and ITA AN NG Sane rcs crams sen ect cseraanaaccactsnrpncet raat aerate Serstmoatcnaseigele n rrr errr errre nnr er Ere nnne rnrn rnrn rrena 16 Safety Instructions Before using always make certain that e the lift is assembled as the instructions says e the safety split pin or nut is securely fastened in the bolt that holds the sling bar or other accessories all
10. it the vest from sliding up The height to which the Remember that Sabina has two speeds For user is to be lifted must be decided and tested maximum comfort the mast must be locked in each individual case into the base in the best possible of the three alternative holes See page 6 illustration 2 A Make sure the vest s loops are correctly fastened when the straps are fully extended but before the user is clear of the seat 11 Liko www liko com Sit to stand lifting with Sabina and side support with the active participation of the user Side Support Prod no 2027100 is an accessories for Sabina Side support is intended for users with poor lateral stability Follow the instructions on the previous page This page contains further information 1 Mount Side support on Sabina with 2 Place the sit to stand vest around the user support arms directed towards the user according to the instructions for that particular Secure with screw and wing nut M8 vest gt lt ISN aa 3 Raise Sabina about 10 20 cm 4 8 inch 4 Continue lifting to desired height The user grasps the sling bar and the lifting procedure can continue If the user leans backwards during the lift this facilita tes lifting and prevents the vest from sliding up The height to which the user is to be lifted must be decided and tested in each individual case Make sure the vest s loops are corr
11. n the charger e Kneepad lights when charging Lever for base width adjustment mod EM Individual adjustment of lifting height Best position User s height Pos O gt 170 cm lt 5 7 160 190 cm 5 3 6 3 2 3 gt 180 cm lt 6 Ft 1 Lower the mast into the pipe on the base 2 When securing the mast to the base as shown in the picture you have the option of setting the liftspan in three different levels Choose one of the three holes to secure the mast to the base The distance between two holes is 5 cm 2 inches Use locking handles or screw M10x60 and lockingnut M10 Tighten with tool if you use screw and nut 3 Push the sling bar forward on 4 Mount the locking knob 5 Place the removable battery the lift arm with the hooks ope and tighten pack into position on top of the ning upwards electronic power pack Check that the batterypack is locked to the assembling part A click sound will be heard 6 Liko www liko com 8 Insert the extension cable in the tension clip underneath the control box 11 Reset the emergency stop by turning the button in the direction shown by the arrow on top of the button 14 Mount lever for base width adjustment mod EM Press in the catch on the undercarriage Slide lever into place Turn the lever until it clicks securely in place on the undercarriag
12. ort should be thoroughly serviced at least once per year Pay particular attention to parts that show wear for example joints bolts etc Service must be carried out according to Liko service manual and by authorised staff WARNING Use only authorised Liko service personnel and Liko spare parts Transportation and storage During transportation or when the patient lift is not to be used for some time the emergency stop button should be pushed in Also when storing keep the patient lift at a temperature exceeding freezing point and at a relative humidity no more than 60 We always try to improve our products Naturally this means changes from time to time Please contact our local representative or your nearest Liko office to receive the latest updates Made in Sweden 1 Liko www liko com Manufacturer National Distributor in USA and Canada Liko Distributor in UK Liko AB Liko Inc Liko UK Ltd SE 975 92 Lulea 842 Upper Union Street suite 4 Liko House L amp M Business Park Sweden Franklin Ma 02038 USA Norman Road Altrincham Cheshire info liko se Phone 508 553 3993 1 888 545 6671 WA 14 4ES UK Fax 508 528 6642 Phone 0161 926 8067 info likoinc com Fax 0161 929 7050 info liko co uk
13. r of the two lower pushbuttons lt 7 Out gt in The base width of the lift model EM is manually adjus ted by a lever The lever can be put in different posi tions Move the lever backwards to unlock it then move it sideways to adjust the width The lever locks automati cally the battery needs charging a LED lamp A is lit on the handcontrol There is however enough capacity left in battery for several lifts Emergency Stop To use the Emergency Stop Push the red Emergency Stop button To reset Turn the button in the direction shown by the arrows Electrical Emergency Lowering For electrical emergency lowering rising use a thin object and press into the hole marked on the power pack A The object used to press must not be too sharp Mechanical Emergency Lowering To use the Emergency Lowering Turn the red Emergency Lowering cylinder in the direc tion shown by the arrows Locking the wheels necessary the rear wheels can be locked To lock step on the foot brake To release the brake press the upraised release mechanism 8 Liko www liko com Charging the batteries To obtain maximum life of the batteries it is important that they are being charged regularly We recommend charging every night after using the lift Check that the emergency stop button is not pushed in The battery charges fully in 6 hours The charger
14. ry Liko Instruction Guide 7EN55103 2000 08 18 Sabina Model EM ES Sabina Comfort Model EM ES Sabina is a sit to stand lift especially Sabina Comfort in combination with Liko Com designed for patients who are able to fort Vest offers extra ease and comfort in lifting actively participate in the standing exercise particularly for users who are sensitive to pres for example when transferring to the toilet sure under the arms This makes it especially Sabina and Sabina Comfort can be used for Sultable for people who are paralysed on one physiotherapy to help the patient activate the Side muscles needed for standing up and putting To a limited extent both Sabina and Sabina weight on their legs and feet Comfort may also be used with certain models of the regular Liko slings to transfer patients who are unable to actively participate A Caution triangles are used to warn of situations that demand extra care and attention CAUTION Carefully read these instructions and the instructions for the particular lifting accessory being used Lifting and transferring patients always presents a potential risk It is essential to thoroughly understand the content of these manuals and that only trained persons use the equipment you have questions please contact Liko or your local Liko representative www liko com Table of Contents ISTIC ONS ses a E E E E E E E E EE A 3 4 Technical Specif
15. shuts off automatically once the battery is fully charged Charging must not take place in a wet area If the lift is not used daily we recommend that you press in the emergency stop This cuts the electrical current and saves battery power A NOTE During charging an indicator lamp on the control box illuminates see page 4 position 22 When the batteries are fully charged the lamp shuts off If the indicator lamp continues to light after 8 hours the batteries probably need to be replaced Discontinue the charging and change the batteries Alternatives of charging With built in charger Take the coiled cable and plug into the socket 100 230V Check that the LED lamps on the electronic power pack lights which indicates charging With wallmounted charger 1 Loose the holder for the chargercable 2 Remove the battery from the electronic power pack and place this on top of the wallmounted charger Check that the charger is plugged in to the socket and that the lamp on the front of the charger lights when charging RP XK Old batteries are to be left at personal authorised by Liko or to the nearest station Ph for environmental recycling Accessories for Sabina and Sabina Comfort Wallmounted charger Extra batterybox incl batteries Sabina sidesupports prod no 2004106 prod no 2006106 prod no 2027100 9 Liko www liko com
16. y contact plate is not defective or broken off Check that the charging cable is not connected to the wall socket If the lift still does not work satisfactory contact Liko Battery charging does not work 1 Check that the emergency stop button is not pushed in 2 Check that the battery contact plate is not defective or broken off 3 Ifthe lift still does not work satisfactory contact Liko The lift stops in the elevated Check that the emergency stop button position is not pushed in Check that the battery is charged Use the emergency lowering device marked If the lift still does not work satisfactory contact Liko If you hear unusual sounds gt Contact Liko 15 Liko www liko com Copyright Liko AB 2000 08 Care and Maintenance For safe and troublefree operation there are a few routine measures which should be performed every day the lift is used e Visually inspect the patient lift and check for external damage or wear Check that all screws are tight e Check that the safety latches on the sling bar work properly e Check the hand control and the lift and width movements Check the emergency lowering function e Charge the battery every night after use or with the frequency needed needed clean the patient lift with warm water or ethanol Warning Do not use chemicals containing phenol or chlorine since the aluminium parts may be damaged Sabina and Sabina Comf
Download Pdf Manuals
Related Search