SB-E-25.0510 ISS.05 Technical Bulletin
Contents
1. DEVILBISS CUE SB E 25 0510 ISS 05 C Technical Bulletin t2 oVISOR Table of Contents Topic EC Declaration of Conformity Introduction Description Warning Start Up Warning Device Fitting Visors Maintenance amp Cleaning Storage amp Transportation Caution Maintenance Record Replacement Parts Exploded Parts View Warranty Page N o gt O O aA a oa AA A 00 O 2012 Finishing Brands UK Ltd EC Declaration of Conformity The unit is CE marked to PPE Directive 89 686 EEC EC type examination by BSI Kite mark Court Davy Avenue Knowlhill Milton Keynes MK5 8PP U K Notified Body No 0086 and conforms to EN 14594 2005 Class 3A It is fully approved when used in accordance with these instructions This unit has a resistance to flammability in accordance with section 6 9 of EN 14594 2005 We recommend the unit to be used between the normal atmospheric temperatures of 0 C to 45 C The visor is suitable for use in zones 1 and 2 hazardous areas with gas groups IIA and IIB Certificate SRO136 D Smith General Manager 2nd August 2012 Introduction Thank you for choosing the Pro Visor we hope it will give many hours of trouble free service Please read all the following instructions carefully and keep all literature safe as it will be necessary when ordering spares The materials used in this helmet have been carefully selected to provide a product of minim2. UK Ltd HEAD WIDTH ADJUSTMENT RIGID VISOR SPACER NOTE RIGID VISOR TO LOCATE ON SPACER INLET SEE START UP SECTION FOR PRESSURES BROW GUARD ANN AIRTO SPRAY GUN KNOB HEAD WIDTH ADJUSTMENT SPACER STUD COLOUR HEAD SIZE ADJUSTABLE HEAD RED SMALL i MIRAME YELLOW MEDIUM GREEN LARGE ITEM 15 SEE TABLE BLACK NO SPACER REQUIRED X LARGE O 2012 Finishing Brands UK Ltd WARRANTY This product is covered by DeVilbiss one year warranty Finishing Brands UK Limited Ringwood Road Bournemouth BH11 9LH UK Tel No 44 0 1202 571111 Fax No 44 0 1202 581940 Website address http www finishingbrands eu Registered office Finishing Brands UK Limited 400 Capability Green Luton Bedfordshire LU1 3AE UK Registered in England No 07656273 Vat No GB 113 5531 50 10 2012 Finishing Brands UK Ltd
3. ce in a bag to protect the unit from dust It should be stored in a cool dry room at 30 C to 60 C out of direct sunlight The visor needs to be transported in the storage bag supplied in a safe manner to maintain the integrity of the unit Caution Do not hang the Pro Visor by the breathing air tube O 2012 Finishing Brands UK Ltd Pro Visor Maintenance Record Part Changed Date Name O 2012 Finishing Brands UK Ltd Replacement parts Item No Part No Description 1 PROV 600 Pro Visor complete unit 2 PROV 20 K Belt 8 Regulator 3 PROV 21 K Peak 4 PROV 22 K10 Tear off visors pack of 10 5 PROV 22 K50 Tear off visors pack of 50 6 PROV 23 K Belt and Buckle 7 PROV 406 K 1 2m Hose To Spray Gun 8 PROV 25 K Rigid acetate visor face seal and air tube 9 PROV 26 K Storage bag 10 PROV 27 K4 Filter element Pack 4 11 PROV 28 K4 Comfort brow band Pack 4 12 H 6085 QD 10m Air hose 5 16 ID male amp female QD s 13 H 6065 B eee 5 16 ID BSP G swivel F 14 PROV 29 K Visor head piece amp Breathing air tube 15 PROV 30 K Spacer Stud amp Knob set of all sizes 16 PROV 31 K Filter cap amp Seal 17 PROV 32 K Y Piece Assembly 18 PROV 33 K QD Connector 19 PROV 34 K4 Filter cap seal Pack of 4 2012 Finishing Brands
4. he Pro Visor Should the whistle sound during use the operator should vacate the spraying area immediately with the unit still on and check the air supply e look for crushed or cut supply hose Each time the Pro Visor is used the device should be checked in a safe area to do this the headpiece should be worn as normal and the air supply reduced to approximately 1 bar or less this will cause the whistle to sound when the pressure is restored to a safe level the whistle silences Fitting Headpiece The headband is adjustable and operated by a ratchet at the rear To adjust pull the knob out then turn to tension push to lock A snug fit around the head sufficient to prevent involuntary movement of the unit is required The top band is set with a series of adjustment holes The elasticated face seal should pulled under the chin with the tab and touch the face all round Caution facial hair may prevent the correct fitting and sealing of the headpiece The headpiece comes complete with width spacers to ensure a good fit to the head these can be inter changed to achieve the most comfortable fit see exploded view for fitting Regulator waist belt The belt strap is adjustable at the buckles and the tidy slides prevent the ends hanging loose The regulator assembly can be located on either side of the waist Visors i Rigid visor Press the top centre of the visor from the outside of the unit releasing it from the retaining hook
5. on the inside of the black brow guard simultaneously rotate the visor down the visor is released To refit the visor first locate the ends on the mounting bosses then rotate upwards ensuring the visor goes inside the four location slots in the brow guard Finally make sure the visor snaps home over the retaining hook This rigid visor complies with BS EN14594 2005 section 6 16 2 2 Do not use the Pro Visor without a tear off disposable visor fitted ii Tear off disposable visors These are supplied in packs of 10 or 50 they are to be fitted one at a time over the brass studs located on the rigid visor 2012 Finishing Brands UK Ltd Maintenance and Cleaning All components of the Pro Visor may be cleaned with a damp cloth and mild disinfectant If the unit is immersed in water the foam on the visor will need time to dry The unit or parts must be replaced when it no longer gives the operator the original designed protection i e a hole or split in the seal or scratches to the rigid visor No maintenance should be attempted to parts inside the regulator waist belt assembly covers except for the activated carbon filter which should be replaced quarterly every 3 months Unscrew the filter cap and then the filter ensure the seal is on the filter cap when replacing The tear off disposable visors should be used to prevent the rigid visor becoming contaminated Storage amp Transportation After use thoroughly clean and dry pla
6. piece air hose must be connected to the connection on the top of the regulator Compressed air supply shall have suitable filters to provide breathing air compliant with BS EN12021 1999 such as DeVilbiss DVFR 2 or DVFR 8 with no excessive moisture to avoid freezing of the apparatus this air must contain no less than 19 5 Oxygen It is the operators responsibility to check the air supply The unit must not be connected to any other gas supply i e Acetylene Oxygen Nitrogen Argon or Oxygen enriched air etc Care should be taken to ensure the compressor only draws in clean air i e site compressor away from vehicle exhausts ventilation outlets and any other toxic emissions of any nature including Carbon Monoxide The user must check that the capacity of the air system is sufficient for every user connected to it in accordance with these instructions Air connection Air supply hose item 12 or 13 not included should be connected to the bottom of the waist belt regulator a Working dynamic air flowing pressure of 4 0 bar 60 psi minimum to 7 0 bar 100 psi maximum is required A single hose of 10 metres maximum length from the air supply filtration set is allowed Pro Visor air flow rate 128 160 l min 4 5 5 7 SCFM Noise level at 160l min 69 7db 2012 Finishing Brands UK Ltd Warning Device A whistle is incorporated to warn the operator that an insufficient quantity of breathing air is being supplied to t
7. um weight and maximum safety This unit is not designed to protect the operator from falling objects None of the materials used are known to have any ill effects on health or cause any skin irritations Description The compressed air fed Pro Visor is specifically designed for use in Paint spray applications and will protect the wearer from airborne contaminants during painting A hose is provided for spray gun connection It is suitable for use in zones 1 and 2 hazardous areas with gas groups IIA and IIB Certificate SRO136 providing the unit is fitted with one tear off disposable visor see page 5 and the air supply hose item 12 or 13 not included are used which must be attached to an earthed supply connection 2012 Finishing Brands UK Ltd At all times the user must be able to escape the area without the use of the apparatus The unit comes complete with 1 Head top visor assembly with breathing air tube 2 Regulator waist belt assembly with low pressure warning device 3 Pack of 2 tear off disposable visors Warning At very high work rates the pressure inside the device may become negative at peak inhalation flow Adequate protection may not be provided by this apparatus in certain highly toxic atmospheres The air supply hose item 12 or 13 must be used to maintain CE compliance Only use DeVilbiss genuine spare parts to ensure CE approval and safety is maintained Start Up Prior to use the head
Download Pdf Manuals
Related Search