SERVICE MANUAL MODEL SSP-351-D-M
Contents
1. Ohm Meter 1 4 Nut Driver Flat Blade Screw Driver Security Tool CEECO Part Number 301 064 CEECO 7 Communication Equipment amp Engineering Company PROPRIETARY 6 0 6 1 6 2 6 3 6 4 6 5 6 6 6 7 6 8 ISSUE 4 0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS Using a 301 064 security tool sold separately loosen and remove the security screws The security tool is for a standard 5 32 button head screw generally used on the framework of the phone booths Carefully separate the faceplate assembly from the mounting box by gently pulling the faceplate forward Determine and remove the desired knock out hole for running the telephone wire and mount the masonry box as needed Run the telephone wire into the box and terminate on the provided RJ11C modular jack as depicted on the following page The CEECO provided modular jack must be used as it contains required over voltage protection circuitry The use of a gas tube or carbon station protector is recommended The station ground should not exceed 50 ohms Plug the modular line cord from the faceplate assembly into the RJ11C terminal block Dress the line cable and modular jack away from the security screws and seat the faceplate into the housing enclosure Secure the faceplate assembly by tightening the security screws WARNING A Never install telephone wiring during a lightning storm B Never install telephone jacks in wet locations unless the2. BER 587 5450 WITH A NORMAL 1 SEC DIAL TONE DELAY NOTE UNUSED JUMPERS MUST BE REMOVED FROM BOARD RETAIN THEM FOR FUTURE USE ATD 11 PCB AUTOMATIC TONE DIALEF CEECO 6 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 PROGRAMMING CONTINUED 4 0 5 0 3 7 In most installations the J2 mini jumper will remain in the 1 position bridging the center and left copper pins If dial tone delivery is delayed by more than one second however then J2 will have to be set in the 3 position A simple test would be as follows with the telephone line cord connected to the intended telephone line temporarily remove the J2 mini jumper As accurately as possible measure the time delay between the moment the handset is lifted and the moment the phone receives dial tone Try it several times If this time is consistently 1 second or less position the J2 jumper on the 1 position Otherwise position the J2 jumper on the 3 position to set the delay before dialing to 3 to 4 seconds TESTING OPERATION 4 1 Program the phone according to section 3 0 4 0 handset Phone waits one and one half to four seconds depending onthe position of J2 per Section 3 7 The programmed number is automatically dialed 4 3 transmitter is muted while the phone is dialing 4 4 Incoming calls are not able to be detected due to the lack of a ringer RECOMMENDED TOOLS AND TEST EQUIPMENT Volt
3. RY box 7 13 32 H x 3 W x 3 D 5 amp 3 4 Knockouts Hardware Approximately 3 Ib 0 4A BW 88T7 13716 TE T 6 5 RJLIC CEECO 10 Communication Equipment amp Engineering Company PROPRIETARY 8 0 PARTS LIST QUANTITY PART NUMBER 1 350 169 1 301 004 1 301 009 1 301 592 1 301 018 1 331 003 1 310 101 4 311 008 1 301 001 OPTIONS 1 301 064 ISSUE 4 0 DESCRIPTION ATD 11 Automatic Tone Dial Handset with Armored Cord Network Receiver Operated Magnetic Hookswitch Modular Cord Stainless steel panel Dialer Network Mounting Bracket Security Screw 6 32 x 1 1 2 Mounting Box Standard 4 Gang Electrical Masonry Box Security Tool CEECO 11 Communication Equipment amp Engineering Company PROPRIETARY 9 0 ISSUE 4 0 FCC NOTICE 9 1 9 2 9 3 FCC REGISTRATION AND REPAIR INFORMATION Your new telephone has been registered with the Federal Communication Commission FCC in accordance with Part 68 The FCC requires that you be advised of certain requirements involving the use of this telephone CONNECTION WITH THE NATIONWIDE TELEPHONE NETWORK The FCC requires that you connect this telephone to the Nationwide Telephone Network through a registered jack provided by the telephone company in your area This jack is a modular outlet which you can order from your local telephone company NOTIFICATION TO THE TELEPHONE COMPANY Before connecting this telephone the FCC requires that you no
4. SSP 351 D M ATD11 ISSUE5 0 SERVICE MANUAL FOR MODEL SSP 351 D M STAINLESS STEEL PANEL TELEPHONE EQUIPPED WITH ATD 11 BOARD p Communication Equipment Serving the Telephone Industry Since 1930 519 West South Park Street Okeechobee Florida 34972 Voice 863 357 0798 Fax 863 357 0006 amp Engineering Company ISSUE 4 0 IMPORTANT INFORMATION FOR CUSTOMER Please fill in before you continue The following information is necessary when calling CEECO for assistance MODEL NUMBER MODEL SSP 351 D M STAINLESS STEEL PANEL TELEPHONE SERIAL NUMBER DATE MANUFACTURED LOCATION INSTALLED For us to better serve you please have this information available when calling for technical support CEECO Communication Equipment and Engineering Company 519 West South Park Street Okeechobee Florida 34972 863 357 0798 Voice 863 357 0006 Fax CEECO 2 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 TABLE OF CONTENTS SECTION PAGE 1 0 TN PRODUC LION fees D 4 2 0 GENERAL DESCRIPTION 4 3 0 PROGRAMMING ee P 5 PROGRAMMING DIAGRAM PROGRAMMING CONTINUED 6 PROGRAMMING CONTINUED e eese eerte 7 4 0 TESTING OPERA TION 25 509 7 5 0 RECOMMENDED TOOLS AND TEST EQUIPMEN
5. T e eeeeeeee ertet 7 6 0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS 8 7 0 SPECIBICA LIONS eere reote 10 8 0 225 uS 11 9 0 FECE Eis ctccssvisepseniasanssseoswneseussveraesineneeyevebeopersids oossoo eoo s eisso etoso sp esio 12 10 0 REPAIR AND RETURN 2 2 2 2 01 101 074 13 11 0 WARRANTY POLICY siccescissscossssesassesessconuasecscpencasdohostunsnatsnnncsbseseansnareeecenaeselecs 14 CEECO 3 Communication Equipment amp Engineering Company PROPRIETARY 1 0 2 0 ISSUE 4 0 INTRODUCTION The practices in this manual provide installation and maintenance information for Model SSP 351 D M Stainless Steel Panel Telephone The information in this manual is subject to change without notification For information not included in this manual please call or write CEECO Customer Service 519 West South Park Street Okeechobee Florida 34972 863 357 0798 863 357 0006 FAX GENERAL DESCRIPTION The CEECO Model SSP 351 D M Stainless Steel Panel Telephone is an automatic tone dialing phone designed for special applications where a telephone must fit into tight space restrictions within a wall It mounts by way of a standard 4 gang electrical masonry box It is equipped with an ATD 11 automatic tone dialer that will dial a single number of up to eleven 11 digits The automatic dialing
6. feature is activated by hookswitch closure The SSP 351 D M may receive calls but the auto dialer will still send out the digits upon the initial answer A normal conversation may take place thereafter The SSP 351 D M incorporates a receiver operated magnetic hookswitch that helps to seal the unit against water and foreign matter penetration as well as eliminates moving parts for long life operation under harsh conditions CEECO 4 Communication Equipment amp Engineering Company PROPRIETARY 3 0 ISSUE 4 0 PROGRAMMING NOTE It is recommended that you ground yourself to prevent ESD 3 1 3 2 3 3 3 4 3 5 3 6 damage to the PCB s This can be done through the use of an electrostatic bracelet or other such device In the absence of any such device it might suffice to simply touch a conduit or other grounded pipe or object to dissipate any built up static electricity Please refer to the diagram on the next page for mini jumper location and positioning Programming is accomplished by position plastic hardware mini jumpers in the proper positions for the desired calling pattern The mini jumpers are designed to bridge pairs of copper pins to activate the desired dialing pattern Locate the ATD 11 Automatic Dialer If the number to be programmed is a 1 call position the J1 mini jumper on the 1 position bridging the left and center copper pins This will cause the digit 1 to be dialed in front of the other pr
7. jack is specifically designed for wet locations C Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface D Use caution when installing or modifying telephone lines CEECO Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 6 9 OVER VOLTAGE PROTECTION DIAGRAM PROPRIETARY CONFIDENTIAL This drawing and all information contained therein is confidential and is the exclusive property of CEECO and may not be copied reproduced or disclosed to anyone in any manner whatsoever or used for any purpose other than for which it is provided to you without the prior written permission of CEECO CEECO 9 Communication Equipment amp Engineering Company PROPRIETARY 7 0 SPECIFICATIONS INPUT POWER LOOP CURRENT IMPEDANCE SIGNALING HEARING AID COMPATIBLE ENVIRONMENTAL PROGRAMMING TELEPHONE COVER PANEL TELEPHONE DIMENSIONS MOUNTING MEMORY RETENTION WEIGHT RINGER EQUIVALENCY FCC REGISTRATION UL LISTED NO TYPE JACK ISSUE 4 0 C O Line Powered 23mA min to 80mA max 600 ohms DTMF 70ms tone 50ms spacing Meets EIA standards Temperature 0 C to 50 C Humidity 20 90 non condensating Via 10 Position Matrix Switch Brushed 16 ga Stainless Steel 4 55 Wide x 8 1 4 High x 2 60 inside box x 3 10 outside box with handset on hook Standard 4 gang electrical MASON
8. ogrammed digits If the number to be programmed is a local call position the J1 mini jumper on the B position bridging the center and right copper pins If a 3 digit area code is to be dialed the J3 mini jumper must be set to the 11 position bridging the center and left copper pins If the number being dialed does not require the area code position the J3 mini jumper on the 8 position bridging the center and right copper pins Set each mini jumper on the A K matrix board to correspond to the digits of the number to be dialed Beginning with column A at the top position the plastic mini jumper to bridge the pair of copper pins corresponding to the desired digit 1 0 Proceed in the same manner from left to right until all desired digits are programmed Do not skip any columns as the digits must be represented in an unbroken string Any unused mini jumpers must be removed from the board to ensure proper dialing Do not discard the unused jumpers as they may be needed for future use It is recommended that they be taped or otherwise secured somewhere nearby within the device Be sure each mini jumper is properly positioned to make good contact and dial the intended number CEECO 5 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 PROGRAMMING DIAGRAM J2 JUMPER SEI FOR 1sec OR Ssec DELAY ILLUSTRATION DEPICTS SETTINGS WHICH WILL AUTO DIAL THE LOCAL NUM
9. requested no later than 30 days after original shipment CEECO 13 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 11 0 WARRANTY POLICY 11 1 GENERAL CEECO products are guaranteed to be free of defects in material and workmanship for a period of 365 days from the date of original purchase CEECO s obligation under this warranty is limited to repair or replacement of any part found to be defective by CEECO Under no circumstances shall CEECO be liable for loss damage cost of repair or consequential damages of any kind which have been caused by neglect abuse acts of God or improper operation of equipment CEECO will repair or replace any unit during this period if found to be defective for reasons other than abuse and improper use or improper installation It is the buyer s responsibility to return the defective unit to the factory CEECO will then repair or replace any defective parts and return them to the buyer free of charge PRINTED CIRCUIT BOARDS Printed circuit boards should not be field repaired Ifa unit is found to be faulty replace it with another unit and return the faulty unit to CEECO for repair Modifications by any one other than CEECO will void the warranty CEECO 14 Communication Equipment amp Engineering Company PROPRIETARY
10. tify your local telephone company business office The number is in the front of your phone book Tell them The line to which you will connect the telephone your phone number and the telephone s FCC registration number and ringer equivalence number These numbers are listed in Section 9 0 The FCC further requires that you notify your local telephone company when permanently disconnecting this telephone CEECO 12 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 10 0 REPAIR AND RETURN INFORMATION 10 1 10 2 10 3 10 4 WARRANTY REPAIR Any device returned requiring warranty service repair or credit must be accompanied with a Return Material Authorization RMA FORM It must include return shipping instructions original purchase order number and special marking instruction A description of the trouble observed must be attached to the defective unit This information must be inside the shipping container DIRECT ALL INQUIRES TO CEECO Repair Department 519 West South Park Street Okeechobee Florida 34972 863 357 0798 NON WARRANTY REPAIR CEECO will repair equipment out of warranty for a set charge plus parts The customer must pay the shipping costs both directions RETURN FOR CREDIT Material may be returned for credit only with prior approval Material not authorized for return is subject to a 20 restocking charge based on the manufacturer s list price Return RMA must be
Download Pdf Manuals
Related Search