003-2189-00_User Guide, Elevance Chair
Contents
1. 0 WAVE SerenEscape heat and message functions each have timers that turn off automatically after 20 minutes without user input DA2862i 2010 Midmark Corp 60 Vista Drive Versailles OH 45380 USA 1 800 643 6275 1 937 526 3662 midmark com 10 Style A Hand Control Operation for Massage and Heat Note Indicator lights beside each button illuminate when the function is ON PWR Power Button e Press to toggle massage motors ON and OFF e Green PWR light illuminates when ON HEAT Button e Press to toggle heat ON and OFF e Green HEAT light illuminates when ON HIGH and LOW Buttons e Press HIGH or LOW button to select e Orange light illuminates beside the active selection Heat Controls Massage Controls INT Intensity Arrows Use to increase or decrease massage depth Massage mode selections Press FLAT button to select flat massage mode Flat massage constantly runs both left and right massage motors at the same time Blue light beside the FLAT button illuminates when flat mode is active Use INT arrows to increase or decrease the depth of the massage SPD arrows are not applicable to the flat massage mode Press PULSE button to select pulse massage mode Pulse massage turns both left and right massage motors ON then OFF together Blue light beside the PULSE button illuminates when pulse mode is active Use INT arrows to increase or decrease the depth o2. mounting hole on the top of the headrest mount B Insert the magnetic headrest into the mounting hole affix the magnetic support headrest to it if desired and adjust to the desired position before tightening the Clamp Knob C Pull up or push down on the headrest assembly sliding the mounting bar to the desired height Clamp Knob Headrest Mounting Hole Magnetic Mounting bar Support Headrest Magnetic Headrest DA2073i 2010 Midmark Corp 60 Vista Drive Versailles OH 45380 USA 1 800 643 6275 1 937 526 3662 midmark com 8 Rotating The Chair Chair Rotation limits 38 Brake Release Pedals 2010 Midmark Corp 60 Vista Drive Versailles OH 45380 USA 1 800 643 6275 1 937 526 3662 midmark com DA2064i To rotate the chair Step on a brake release pedal and hold it down As long as a brake release pedal is depressed you can rotate the chair Release brake release pedal to engage the rotational brake pin and prevent chair from rotating Note When a brake pedal is pressed listen for the click of the brake pin releasing before rotating the chair Rotation limits differ for different Chair Models Model of rotation from center line Chair Only 38 Left and 38 Right L R Chair 15 Left and 15 Right not shown Console Chair Chair Lockout Feature To prevent unintentional chair movements or rotation a Chair Lockout feature is
3. Language of origin English 2010 Midmark Corp 60 Vista Drive Versailles OH 45380 USA 1 800 643 6275 1 937 526 3662 midmark com 1 Style A Part No 003 2189 00 Rev L 9 9 15 ib Compliance Information Intended Use The Chair is intended for use by professional dental practitioners in providing treatment to dental patients in a dental operatory The system is designed to properly position the patient for said treatment Electromagnetic Interference Midmark dental operatory components are designed and built to minimize electromagnetic interference with other devices However if interference is noticed between another device and this operatory remove the interfering device from room and or plug product into an isolated circuit Transportation Storage Operating Conditions Transportation Storage Temperature 23 F to 100 F 5 C to 38 C Relative HUMICItY 0 ccccceeeeeeeeeeeeeeeeees 10 to 90 non condensing Atmospheric Pressure 7 2 PSI to 15 3 PSI 50 kPa to 106 kPa Operating Temperature Range ccee 59 F to 95 F 15 C to 35 C Disposal of Equipment At the end of this product s life the unit accessories and other consumable goods may be contaminated from normal use Consult local codes and ordinances for proper disposal of this equipment and other consumable goods Authorized EU Representative Countries in the EU should direct all qu
4. OR REPLACEMENT OF DEFECTIVE PARTS
5. Program Button Alternate Foot Control Programming Method With the chair button 2 seconds The chair will beep three times to indicate the Note The chair can be stopped any time during a programmed positioning sequence by pressing any other button on the control device DA3544 DA2070 Special Programming Features The number 4 Position Button is capable of being programmed to invoke any one of these three different functions A The Cuspidor Return Function B The Return to the Last Position Function C Function the same as any other Position button Which of these functions the 4 button invokes is dependant on a dipswitch setting on the PC Board and should only be changed by a service technician To recall a programmed position Press desired Position Button 1 2 3 or 4 DA2069_a 2010 Midmark Corp 60 Vista Drive Versailles OH 45380 USA 1 800 643 6275 1 937 526 3662 midmark com Adjusting the Headrest To adjust the headrest A Loosen turn counterclockwise the Clamp Knob and rotate the headrest at the two pivot points to achieve the desired position B Tighten turn clockwise the Clamp Knob to lock the headrest in the desired position C Pull up or push down on the headrest sliding the mounting bar to the desired height Using the optional magnetic headrest A Loosen the Clamp Knob and slide the standard headrest out of the
6. 0 V T3 15AL F3 transformer 250 V TO 080AL E M Classifications Class Type B Applied Part except as noted for optional heated back upholstery Ordinary Equipment Intermittent Operation ES IEC EN 60601 1 CAN CSA C22 2 No 60601 1 Safety Standards EN IEC 60601 1 2 EMC Standards Optional heated back upholstery Type BF Applied Part complies with IEC 60601 2 35 IPXO Dental Chair IPX1 Foot Control IPX2 Heated Back Upholstery Certifications 2010 Midmark Corp 60 Vista Drive Versailles OH 45380 USA 1 800 643 6275 1 937 526 3662 midmark com 13 WARNING Do not modify this equipment without authorization of the manufacturer Caution Federal law restricts this device to sale by or on the order of a licensed dental practitioner A a WARNING A Equipment is not suitable for use in the presence of a flammable anesthetic mixture with oxygen air or nitrous oxide Clarification Equipment is suitable for use in the presence of oxygen air or nitrous oxide I Warranty Information SCOPE OF WARRANTY Midmark Corporation Midmark warrants to the original purchaser its Den tal products and components except for components not warranted under Exclusions manufactured by Midmark to be free from defects in material and workmanship under normal use and service Midmark s obligation under this warranty is limited to the repair or replacement at Midmark
7. Elevance Dental Electromagnetic Interference 2 Transportation Storage Operating 2 a I r Disposal of Equipment cccccceeeeees 2 Authorized EU Representative 2 FCC Compliance Statement 2 Model 1 5381 0 calling TOR SO IVICS orriei 2 BOS cious std antniesuieactonabeoeaeeoone 3 Product Features Power ON Light sicssiie inustusutesnnnnassboaianenans 4 Collision Protection System 4 Brake Release Pedals cccccccceeeeee 4 Chair COTM S iain isa tcnisive asain striction 5 Wireless Remote ccccccececeececeseeeeees 5 F olpad COnTOl scesero 5 Unit Control Pads scsi iiiecisctieusrcortawenrcunds 5 Operation and Adjustments BICK U V OOND osasin eai 6 Chait UD DOWN sicsisriireiisn tisessa 6 Programming Chair Positions id Adjusting the Headrest cc00c0008 8 Rotating the CEI sciacsincacmiisesmuaetaiveiabaasin 9 Chair Lockout Feature ccc0c00 9 Massage and Heat optional 10 Hand Control for Massage and Heat 17 Aeon INA Cleaning _ ore BOE iconic ie iay 12 Serial Number Cleaning Chair Upholstery 004 12 Label Cleaning PrOC QUIes ccccccceeeeeeees 12 Product SpecCifiCatiOns cccccccceeeee 13 Warranty Information 0 0ccceeeee eens 14 Da2072 For installation information go to Technical Library at Midmark com
8. bols appear on your equipment and or in the manuals Warnings and cautions are provided in the manuals where applicable Caution Indicates a potentially hazardous situation which may result in minor or moderate injury if not avoided It may also be used to alert against unsafe practices YD WARNING Indicates a potentially hazardous situation which could result in serious injury if not avoided A Equipment Alert Indicates a potentially hazardous situation which could result in equipment damage if not avoided Note Amplifies a procedure practice or condition an Consult Manual C Duty Cycle Non ionizing Electromagnetic Radiation 2010 Midmark Corp 60 Vista Drive Versailles OH 45380 USA 1 800 643 6275 1 937 526 3662 midmark com 204 kg 450 Ibs 7 iH oO SerenEscape Heat and Massage back uphol stery is a Type BF Applied Part Do not penetrate upholstery with sharp objects such as needles knives etc Relative Humidity Maximum Pati atient Weight Transportation amp Type B Storage Applied Part E Temperature Type T a Atmospheric Fuse m pressure Protective i3 d Earth Ground SRE Keep Dry Fragile EX Maximum stacking D height Refer to n number on package Proper Shipping Transportation Orientation Orientation K POWER ON Light The chair has a POWER ON light that illuminates when electrical p
9. e altera tion accident freight damage or tampering 2 matching of color grain or texture except to commercially acceptable standards 3 changes in color caused by natural or artificial light 4 products which are not installed used and properly cleaned as required in the Midmark Installation and or Instal lation Operation Manual for this applicable product 5 products considered to be of a consumable nature 6 accessories or parts not manufactured by Midmark 7 specially manufactured products 8 charges by anyone for adjustments repairs replacement parts installation or other work performed upon or in connection with such products which is not expressly authorized in writing in advance by Midmark EXCLUSIVE REMEDY Midmark s only obligation under this warranty is the repair or replacement of defective parts Midmark shall not be liable for any direct special indirect inci dental exemplary or consequential damages or delay including but not limited to damages for loss of profits or loss of use NO AUTHORIZATION No person or firm is authorized to create for Midmark any other obligation or liability in connection with the products THIS WARRANTY IS MIDMARK S ONLY WARRANTY AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED MIDMARK MAKES NO IMPLIED WARRANTIES OF ANY KIND INCLUDING ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE THIS WARRANTY IS LIMITED TO THE REPAIR
10. estions incidents and complaints to Midmark s Authorized EU representative listed below Midmark EMEA Ltd Beech House First Floor East Wing Ancells Business Park Fleet Hampshire GU51 2UN United Kingdom Tel 44 0 1252 360 940 Fax 44 0 1252 360 941 2010 Midmark Corp 60 Vista Drive Versailles OH 45380 USA 1 800 643 6275 1 937 526 3662 midmark com FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Any modifications to this product may violate the rules of the Federal Communications Commission and make operation of the product unlawful Calling For Service Direct all service inquiries to your authorized Midmark dealer When calling for service you must provide the following information Model serial number Date of purchase Symptom s of malfunction symbols These sym
11. f the massage Use SPD arrows to increase or decrease how fast both massage motors alternate ON and OFF a ____ Press WAVE button to select wave massage mode Wave massage alternately turns the left and right motors ON and OFF independently Blue light beside the WAVE button illuminates when wave mode is active Use INT arrows to increase or decrease the depth of the massage Use SPD arrows to increase or decrease how fast massage motors turn ON and OFF SPD Speed Arrows Use to increase decrease how fast massage motors turn ON and OFF Has no effect on FLAT massage mode Note After approximately 20 minutes with no user interaction all SerenEscape heat and massage functions turn OFF automatically 2010 Midmark Corp 60 Vista Drive Versailles OH 45380 USA 1 800 643 6275 1 937 526 3662 midmark com 11 Style A ib Cleaning Barriers Single use barriers and disposable items significantly reduce the need for chemical cleaners thus prolonging the life of the equipment Barrier material must be impervious to moisture fluids Examples of protective barriers Plastic covers available from your dealer or equipment manu facturer Clear plastic wrap Plastic bags Plastic sheets Plastic tubing Plastic backed paper Materials similar to those listed here Cleaning Chair Upholstery Spot Cleaning use mild soap and water solution Difficult stains use a mild solvent ex Fantast
12. ic 409 Allow upholstery to air dry or use a hair dryer on the lowest setting Caution A N Midmark assumes no responsibility or liability for any result expressed or implied These are suggested practices based on the best information available at this time this is written 2010 Midmark Corp 60 Vista Drive Versailles OH 45380 USA 1 800 643 6275 1 937 526 3662 midmark com 12 Cleaning Procedures Use cleaners that are appropriate for the situation such as warm water and mild detergents or a 10 solution of bleach with water NOTE Every dental practice is different and no single cleaner is the best choice for every facility Listed below are some organizations to assist you in choosing the best cleaners available for your practice e Organization for Safety amp Asepsis Procedures http www osap org e American Dental Association http www ada org e Dept of Health amp Human Resources Centers for Disease Control amp Prevention CDC http www cdc gov Read all labels carefully DA148100i DA177400i Product Specifications Elevance Chair Power Cord Lenath E ee 7 0 ooo o i oea SSS E ee Oe Pump Motor and Brake 30 seconds ON 5 minutes OFF _ SSS SS BS SS aa SSS SS SSa SjSjaa_jajaaS as Fuses 115 VAC Models F1 amp F2 line input 250 V T6 3AL F3 transformer 250 V T0 16AL SSS Fuses 230 VAC Models F1 amp F2 line input 25
13. lure to comply may result in injury and or damage to equipment Style A Chair Controls Control devices are available to quickly and accurately position the dental chair All control devices are membrane covered keypads with easy to understand graphics All control devices invoke the same chair movements Wireless Remote Control Composite Light Button ny Os Seat and Back For Arrow buttons on all controls activate the Seat and Back Up and Down functions Numbered buttons on all controls are programmable position buttons Function Buttons Programmed Lae Position a Buttons wa Program Button LED Indicator illuminates when any button is pressed 2010 Midmark Corp 60 Vista Drive Versailles OH 45380 USA 1 800 643 6275 1 937 526 3662 midmark com DA2069 Program Button Footpad Control Connects to the Chair by a cord Optional 4 Position Foot Control DA3544 Unit Control Pads Control pads are also found on Doctor s and Assistant s units DA2071 i Operation and Adjustments WARNING Ensure patient is in a seated position while chair is moving Back Up Down Chair Up Down d To Raise or Lower the Chair Press and hold the desired Chair Up or Chair Down button on any control device The chair stops moving when you release the button or it reaches the limit of its range of motion To Raise or Lower the Back P
14. ower is supplied to the chair POWER ON Light DA2063i DA2063i 2010 Midmark Corp 60 Vista Drive Versailles OH 45380 USA 1 800 643 6275 1 937 526 3662 midmark com 4 Brake Release Pedals Collision Protection System Dental Chairs are equipped with a Collision Protection System designed to prevent damage to personnel or equipment If a chair cover hits an object as it is lowering it stops lower ing and raises slightly to disengage contact The chair also beeps until the control button is released Normal operation can then be resumed D Equipment Alert Tap any one of the lift arm covers 3 times to raise the chair to the pre programmed home position a convenient height for installation or patient access The chair beeps as it moves and stops beeping when it reaches the home position Upper Lift _ Arm Cover Lower Lift Arm Cover DA2065i ee o_o Brake Release Pedals To ensure precise steady positioning and prevent unintentional rotation of the chair a brake release pedal is located on either side of the Chair Base Press and hold either of the brake release pedals as you rotate the chair to the desired position Release the brake release pedal to lock the chair in that position WARNING During transportation the chair must be at its lowest height and all attachments secured in their lowest and most central position possible Fai
15. provided Simply press either of the brake release pedals 5 times in succession to activate the Chair Lockout feature The chair beeps 5 times to indicate it is locked Buttons on control devices and the brake release pedals no longer work they are locked out To release the Chair Lockout feature simply press either of the brake release pedals 5 times in succession The chair again beeps 5 times to indicate it is not locked Buttons on control devices and the brake release pedals will function normally again Style A Massage and Heat optional Caution A N e Ensure that the surface of the SerenEscape Back upholstery is free from mechanical damage prior to each application e Do not penetrate SerenEscape Back upholstery with sharp objects such as needles knives etc e Do not use the SerenEscape feature in conjunction with high frequency electrosurgical equipment such as hyfrecators etc e The SerenEscape Back upholstery heats from 20 C 68 F to a range of 85 to 90 F 29 32 C in approximately 10 minutes Chair Back Hand Control The SerenEscape Heat Massage components are embedded in the Back upholstery and are operated by a separate hand control a MIDMARK Heat or Massage can be used separately or HEAT PWR together at the same time HIGH FLAT 0 All buttons on the hand control activate with s Touch and Release operation Just touch and puLse LOW release do not hold down a button
16. ress and hold the desired Back Up or Back Down button on any control device The back stops moving when you release the button or it reaches the limit of its range of motion Back Up Chair Up Chair Down Back Down DA2067i a Equipment Alert VN If pressing buttons on the wireless remote does not invoke any chair movements replace the batteries If new batteries do not remedy the situation reference the Elevance Chair Service manual troubleshooting DA2066i 2010 Midmark Corp 60 Vista Drive Versailles OH 45380 USA 1 800 643 6275 1 937 526 3662 midmark com 6 Programming Chair Positions To program a button to a specified chair position A Use the arrow buttons to move the chair to desired position B Press the Program Button You will hear a single beep to indicate you are in the program mode C Press the desired Position Button 1 2 3 or 4 to set the programmed position to that button You will hear three beeps to indicate the button is programmed in the desired position you can just press and hold a position button is programmed The Control device gives you 3 seconds to press program a Position button after you are in the Program mode After 3 seconds the control returns to the normal operating mode All the numbered O buttons are Position Buttons
17. s option of the parts or the products the defects of which are reported to Midmark within the applicable warranty period and which upon examination by Midmark prove to be defective APPLICABLE WARRANTY PERIOD The applicable warranty period measured from the date of delivery to the original user shall be as follows 1 DENTAL PRODUCTS are warranted against defect in material and work manship for the period indicated below from the time of delivery a Two 2 years for all products and components except for the periods in b thru e b KINK VALVE module carries a ten 10 year warranty c The original light bulb on a new light carries a one 1 year warranty d Accessories not manufactured by Midmark are excluded A m M A e Replacement parts and accessories carry a ninety 90 day warranty 2 Oral Surgery PRODUCTS are warranted against defect in material and workmanship for a period of one 1 year from the time of delivery 3 STERILIZERS PRODUCTS are warranted against defect in material and workmanship for a period of one 1 year from the time of delivery 4 ULTRASONIC CLEANER PRODUCTS when used in accordance with manufacturer s instructions and under normal use are guaranteed for two 2 years after date of shipment Within the period guaranteed the manufacturer will repair or replace free of charge at its sole discretion all parts that are defective because of material or workmanship includ ing co
18. sts for removing or installing parts Repairs are made on a FOB repair depot basis Manufacturer s liability whether based on warranty negligence or other cause arising out of and or incidental to sale use or operation of the transducer elements or any part thereof shall not in any case exceed the cost of repair or replacement of the defective equip ment and such repair or replacement shall be the exclusive remedy of the purchaser and in no case shall manufacturer be responsible for any and or all consequential or incidental damages including without limita tion and or all consequential damages arising out of commercial losses 2010 Midmark Corp 60 Vista Drive Versailles OH 45380 USA 1 800 643 6275 1 937 526 3662 midmark com 14 5 INTEGRA DENTAL CASEWORK AND ARTIZAN DENTAL FURNI TURE PRODUCTS are warranted against defect in material and work manship for the period indicated below from the time of delivery a Five 5 years for all products and components except for the shorter periods in b and c including plastic laminate top surfaces door and drawer fronts casters and electrical components such as task lights and cords b Three 3 years for task light ballast c One year 1 for plastic laminate solid surface countertops and accessories EXCLUSIONS This warranty does not cover and Midmark shall not be liable for the following 1 repairs and replacements because of misuse abuse negligenc
Download Pdf Manuals
Related Search