OPERATION MAINTENANCE SERVICE MANUAL
Contents
1. etant ote nine is 3 Electrical Installation Requirements 6 Wire Colors and Function 2 6 Test Electrical 9 Bleeding and Brake 10 Testing and Adjustment 12 Troubleshooting Guide and Replacement Kits 13 Limited Warranty ae er an 16 Scan to view installation video This is the safety alert symbol It is used to alert you to potential injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death Actuator Installation Instructions Getting Started The following materials are required to properly install the Dexter E H brake actuator If your trailer is not already equipped with brake lines you will need enough 346 diameter automotive brake line to connect the trailer brakes to the unit Where possible steel tubing is preferred suoiongjsu uomejejsu e Four 14 threaded fasteners to mount the unit to the trailer One quart of DOT 3 DOT 4 or DOT 5 brake fluid from a new sealed container One emergency breakaway kit must include a 12 volt 9 amp hour minimum battery Wire see Electrical Installation Requirements for proper wire size Location of the Dexter E H brake actuator is at the discretion of the vehicle owner When selecting the location the following items should be considered2. 1 The shorter the wiring between the unit and the electrical power source the smaller the voltage drop 2 The unit should be located so that the electrical wiring and brake lines can be neatly routed directly to the towing vehicle and trailer brakes Special care should be taken to minimize the number of bends and fittings in the brake line circuits 3 An emergency breakaway kit must be located on the trailer so that the trailer breakaway cable can be easily attached to the towing vehicle ld ld 4 The Dexter E H brake actuator is powered from the electrical system on the tow vehicle In order for the unit to function properly it must have adequate electrical power see Electrical Installation Requirements 5 The Dexter E H brake actuator should not be placed in an area where it is susceptible to damage from trailer loads road debris or from being stepped on Failure to protect the actuator from damage can cause the unit to malfunction and void the Dexter Axle warranty Mounting consideration should be given to the following 1 The unit must be level with the filler neck up 2 Itis the responsibility of the customer to provide necessary fasteners for attachment of the actuator to the trailer 3 Mount unit where it will not be submerged in water 4 Mounting near the hitch is preferred over mounting near the axles The Dexter E H brake actuator contains sensitive electronics that must be protected Drilling addi
3. INNOVATION SINCE 1960 www dexteraxle com 2900 Industrial Parkway East m Elkhart IN 46516 Phone 574 295 7888 Fax 574 295 8666 ISO 9001 Certified a ES 9 14 O 20005 2014 Dexter Axle Company LIT 608 00
4. OPERATION MAINTENANCE SERVICE MANUAL ELECTRICALLY CONTROLLED HYDRAULIC BRAKE ACTUATION DEVICE E H 1000 amp 1600 BRAKE ACTUATORS a Ey A Aan gt I i gt DEXTER AXLE www dexteraxle com Introduction This manual has been provided to guide you through the process of installing operating and maintaining your Dexter electrically controlled hydraulic brake actuation device also referred to as E H brake actuator This electrically powered unit has been designed and manufactured to give safe reliable power to your hydraulic trailer brakes Before proceeding make sure that the unitis appropriate for your particular brakes The E H 1000 produces 1000 psi typically used for duo servo hydraulic drum brakes while the E H 1600 produces 1600 psi for most hydraulic disc brakes Please refer to your brake manufacturer for proper operating pressures The Dexter E H brake actuator is compatible with many electric brake controllers but the best performance will be achieved using an inertial type controller such as the Dexter Predator DX29 The electronic timer type of controller is not recommended because these units use a fixed control that does not sense varying brake requirements For all your running gear needs Look fist toDenter Visit us online at www dexteraxle com ld Table of Contents Contents Actuator Installation 3 Getting Startedi
5. XPRESS OR IMPLIED WARRANTY Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply to you Inquiries regarding these warranties should be sent to Dexter Axle Company P O Box 250 Elkhart Indiana 46515 Note Current publication Operation Maintenance Service Manual can be found at www dexteraxle com 18 Dexter Video Gallery In keeping with our continual commitment to industry safety and the development of innovative products please feel free to view our ongoing video gallery at www dexteraxle com video_gallery or scan the following QR codes We are confident these videos will help educate and promote the Dexter product line that you as our customer are investing in One my Bearing Genuine Torflex Maintenance Replacement Parts Suspension Axles GERD Opec E E H Actuator Leaf Spring Axles Installation AO m xr i u amp E Z Lube Nev R Adjust System Brakes E a opyo El E Z Flex Removable Suspension Spindle OF AO TELA n Genuine Brakes Sway Control Arajjen 191x3 Dexter Online Parts Store From magnets and seals to complete brake and hub kits Dexter offers a complete line of genuine replacement parts for your trailer Most products are available in stock and
6. al purchaser that its Genuine Replacement Parts shall be free from defects in material and workmanship for a period of two 2 years from the date parts were installed and serviced LIMITED 3 YEAR WARRANTY FOR PARTICIPATING OEMS Dexter Axle warrants to the original purchaser of a trailer equipped with axle models D90 D100GD D100HD D120 or D150 and installed with properly matched Genuine Dexter Hanger and Attaching Parts Kits HAP Kits or Dexter Heavy Duty Suspension System HDSS that this combination of components shall be free from defects in material and workmanship for a period of three 3 years The warranty period shall begin from the date of the original purchase of the trailer LIMITED 5 YEAR WARRANTY Dexter Axle warrants to the original purchaser that its Nev R Lube bearings and the suspension components only of its Torflex axles shall be free from defects in material and workmanship for a period of five 5 years from the date of first sale of the trailer incorporating such components LIMITED 7 YEAR WARRANTY Dexter Axle warrants to the original purchaser that its Predator Series electric brake controllers shall be free from defects in material and workmanship for a period of seven 7 years from the date of purchase EXCLUSIVE REMEDY Dexter Axle will at its option repair or replace the affected components of any defective axle repair or replace the entire defective axle or refund the then current list pri
7. ce of the axle In all cases a reasonable time period must be allowed for warranty repairs to be completed Allowance will only be made for installation costs specifically approved by Dexter Axle WHAT YOU MUST DO In order to make a claim under these warranties 1 You must be the original purchaser of the vehicle in which the spring suspension axles or Torflex axles were originally installed 2 You must promptly notify us within the warranty period of any defect and provide us with the axle serial number and any substantiation which may include but is not limited to the return of part s that we may reasonably request 3 The axles or suspensions must have been installed and maintained in accordance with good industry practice and any specific Dexter Axle recommendations including those specified in Dexter Axle s current publication Operation Maintenance Service Manual EXCLUSIONS These warranties do not extend to or do not cover defects caused by 1 connecting of brake wiring to the trailer wiring or trailer wiring to the towing vehicle wiring The attachment of the running gear to the frame Hub imbalance or any damage caused thereby Parts not supplied by Dexter Axle Any damage whatever caused by or related to any alteration of the axle including welding supplemental brackets to the axle 6 Use of an axle on a unit other than the unit to which it was originally mounted 7 Normal wear and tear 8 Alig
8. commended running clearance Trailer wiring that is too small can cause slow response see section on Electrical Installation Requirements Slow response can be caused by brake line restrictions The trailer brake lines must be at least 346 in diameter Steel tubing is preferred over flexible hoses Check to see if the white ground wire runs directly to the tow vehicle ground IT MUST NOT BE GROUNDED TO THE TRAILER ONLY IT IS IMPORTANT THAT THIS GROUND WIRE RUNS DIRECTLY TO THE TOW VEHICLE S BATTERY GROUND NO EXCEPTIONS Detach all wires from the Dexter Axle E H brake actuator leaving the blue black white and yellow wires loose It is important that the unit is disconnected from any other wires going to the towing vehicle or breakaway switch and breakaway battery Failure to do so may result in a faulty test Using a 12 volt battery connect the white wire to the negative terminal of the battery Connect the black wire to the positive terminal of the battery and the E H brake actuator will click once The motor should not run If the motor runs the E H brake actuator may be defective Leave the white wire connected to the negative terminal of the battery syy juauia2e day pue funooysa qno ld 12 13 14 16 17 18 Troubleshooting and Replacement Kits 2 Connect the blue and black wires together to the positive terminal of the battery The motor should run and the unit shoul
9. ctive After completing the above steps reset the breakaway switch and reconnect the trailer plug Trailer brakes too aggressive 1 Reduce the gain setting on the electric brake controller 2 Check brake adjustment Trailer brakes not aggressive enough 1 Increase the gain setting on the electric brake controller 2 Check brake adjustment Replacement Kits Description Kit Number E H Brake Actuator Fill Cap amp Gasket K71 685 00 E H Brake Actuator Gaskets K71 688 00 syy juauia2e day pue 100459 0001 ld Warranty Dexter Axle Limited Warranty WHAT PRODUCTS ARE COVERED All Dexter Axle Company Dexter Axle trailer axles suspensions and brake control systems excluding Dexter 6000 series Manufactured Housing Axles LIMITED 1 YEAR WARRANTY As specified in Dexter Axle s current publication Operation Maintenance Service Manual grease and oil seals FOR ALL PRODUCTS have a one 1 year limited warranty from the date of first sale of the trailer incorporating such components Except as to grease and oil seals the following four other warranties are available LIMITED 2 YEAR WARRANTY Dexter Axle warrants to the original purchaser that its axles suspension systems and E H hydraulic brake actuators shall be free from defects in material and workmanship for a period of two 2 years from the date of first sale of the trailer incorporating such components Dexter Axle warrants to the origin
10. d pressurize If this does not occur the unit may be defective Leave the white wire connected to the negative terminal of the battery Connect only the yellow wire to the positive terminal of the battery The motor should run and the unit should pressurize If this does not occur the unit may be defective If the unit checks OK reconnect the wires leading to the trailer plug and repeat steps 8 through 14 at the trailer plug If you do not get the same results as before the problem is in the trailer wiring or the electronic brake controller Using the breakaway system to troubleshoot a unit that is not operating correctly 1 With a fully charged breakaway battery and trailer plug disconnected pull the breakaway switch on the trailer a If the unit runs and builds pressure the breakaway system is functioning properly b If the unit runs and builds pressure when the breakaway switch is pulled but will not function under normal operating conditions the problem most likely is a defective electric brake controller or defective wiring between the tow vehicle and Dexter E H brake actuator c If the unit runs but will not build pressure when the breakaway switch is pulled the Dexter E H brake actuator may be malfunctioning d If the unit does not run measure the DC voltage between the white wire and the yellow wire If the voltage is less than 12 volts either the breakaway switch or the breakaway wiring is defe
11. ery only through the black wire on the charger of the breakaway battery Requires an Electric Brake Controller The Dexter E H brake actuator is intended to be used with an electric brake controller in the tow vehicle The unit will operate with a wide variety of controllers but provides optimum performance when used with a Dexter electric brake controller The electric brake controller must have an output capacity of at least 5 amps for proper operation of the Dexter E H brake actuator Although compatible time base brake controllers are not recommended Electrical Requirements It is the responsibility of the end user to ensure that their electric brake controller is compatible with the Dexter E H brake actuator Dexter Axle attempts to provide compatibility with most controllers available but is unable to anticipate design changes that might be introduced by the various controller manufacturers Electrical Connections Make sure all electrical connections are clean dry weather tight and secure to prevent damage to the wiring from dragging or becoming entangled with foreign objects A dedicated ground connection between the tow vehicle and trailer is also required Breakaway Battery Requirement To comply with federal requirements the trailer must be equipped with a breakaway switch and battery The breakaway battery needs to have a minimum capacity of 9 amp hours and needs to be maintained in a fully charged conditi
12. ew of the wheel cylinder caliper farthest from the Dexter E H brake actuator If towed vehicle has multiple axles always start with the rear axle first 6 Immerse the free end of the plastic tube in a clean clear container partially filled with brake fluid 7 Open the bleeder screw one half turn on the wheel cylinder caliper 8 To activate the Dexter E H brake actuator turn the ignition switch on and press on the brake pedal or use manual slide 9 Watch the free end of the bleeder hose for air bubbles escaping into the clear container Continue to bleed the wheel cylinder caliper until the fluid becomes clear and free of bubbles Bleeding and Brake Adjustment Do not run the Dexter E H brake actuator without adequate brake fluid in the reservoir as it may damage the unit and void the warranty Check all bleeder screws to ensure that they are securely closed and do not leak 10 11 12 13 14 Tighten the bleeder screw turn off the Dexter E H brake actuator and remove plastic tubing from the bleeder screw Bleeding of the wheel cylinder caliper is now complete Refill the Dexter E H brake actuator with brake fluid Continue the above process steps 5 through 11 on the next farthest brake away from the actuator Repeat these steps until all the brakes have been bled New trailers with disc brakes should be bled at least twice Any air in the brake system will cause brake delay with an E H brake actuat
13. ing the Dexter E H brake actuator confirms that it is operating It DOES NOT confirm that the brakes are operating properly Regular inspection adjustment and maintenance of the brakes lines hoses drums discs fluid and other associated components is necessary to ensure proper brake operation 6 Some brake controllers will not produce a high enough signal voltage to actuate the trailer brakes when the vehicle is at a standstill Minimal trailer brake force is produced when the controller voltage output to the E H brake actuator is at least 3 VDC Maximum trailer brake force is achieved at 12 VDC on the actuator blue wire 7 When the tow vehicle brakes are released the unit may continue to run for a few seconds 9 ld Bleeding and Brake Adjustment 1 It typically is much easier to bleed the brakes with two people working together 2 Special care must be taken to insure that the Dexter E H brake actuator does not run out of brake fluid Check the fluid level frequently during the bleeding process 3 Block the wheels on the trailer and towing vehicle 4 f the trailer is equipped with drum brakes check that the brake running clearances are properly adjusted consistent with the trailer manufacturers recommendations Failure to properly adjust the brakes on trailers equipped with drum brakes can result in slower response time of the Dexter E H brake actuator 5 Install plastic tubing onto the bleeder scr
14. ion system juawisn py exeig pue 4 ld Testing and Adjustment of Electronic Controller Unit 1 Adjust the gain setting on the electric brake controller to a mid range setting 2 Drive vehicle at 10 to 15 m p h 3 Apply the brakes If braking is too severe adjust the gain setting down to decrease pressure and retest If braking is inadequate increase the gain setting on the electric brake controller and retest 4 Repeat this process until the brakes respond appropriately The appropriate pressure setting will vary depending on the weight of the load being transported on the trailer weather conditions and road conditions The Testing and Adjustment of Electronic Controller Unit procedure should be repeated each time the trailer is used Failure to properly adjust the Dexter E H brake actuator may result in poor brake performance and could result in serious or fatal injuries and or property damage Testing and Adjustment Troubleshooting Guide Unit will not run or brakes are slow to respond To determine if the unit is functioning properly perform the checks outlined below 1 10 Verify that the trailer and tow vehicle are wired according to the electrical schematic shown in Electrical Requirements Re bleed the trailer brakes Any air in the trailer brake system causes brake delay If the trailer is equipped with drum brakes re adjust the drum brakes to the trailer manufacturer s re
15. n sheets provided with the emergency breakaway kit Bolt Mounting Pattern O 9 13 16 250mm 2 1 2 63 5mm suonongjsu uomejejsu ld Electrical Installation Requirements Undersized wire will increase electrical resistance and will prevent proper operation of this unit Wire Colors and Function BLACK 30 amp 12 volt supply from tow vehicle BLUE Output from electronic brake controller in tow vehicle WHITE Trailer and tow vehicle ground YELLOW Cold side of breakaway switch Electrical Schematic From Tow Trailer Vehicle Controller Plug Typically Blue Blue Black 12 Volt 40 Amp gt Circuit From While Tow Vehicle Ground From Tow Vehicle Lanyard BLACK WHITE Break Away 2 o Switch a me elo e 5 3 lc Orange Black m Hydraulic Line cL E Charger Y ha calls Yell Minimum oo zn Hour _ Connect Battery To Tho Note Eitheran onboard or breakaway Ground battery may be used Circuit Itis important that wire lengths for the BLACK power lead and WHITE ground lead be no longer than 25 feet from the E H brake actuator to the supply power i e on board trailer battery or the tow vehicle battery The E H brake actuator needs to be located as close as possible t
16. nment AueuieM ld ld Warranty 9 Improper installation 10 Unreasonable use including failure to provide reasonable and necessary maintenance as specified in Dexter Axle s current publication Operation Maintenance Service Manual including required maintenance after Prolonged Storage 11 Improper wheel nut torque 12 Cosmetic finish or corrosion LIMITATIONS 1 In all cases Dexter Axle reserves the right to fully satisfy its obligations under the Limited Warranties by refunding the then current list price of the defective axle or if the axle has been discontinued of the most nearly comparable current product 2 Dexter Axle reserves the right to furnish a substitute or replacement component or product in the event an axle or any component of the axle is discontinued or is otherwise unavailable 3 These warranties are nontransferable GENERAL THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES EXCEPT THAT OF TITLE WHETHER WRITTEN ORAL OR IMPLIED IN FACT OR IN LAW INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE These warranties give you specific legal rights and you may also have other rights which vary from state to state DEXTER AXLE HEREBY EXCLUDES INCIDENTAL AND CONSEQUENTIAL DAMAGES INCLUDING LOSS OF TIME INCONVENIENCE LOSS OF USE TOWING FEES TELEPHONE CALLS OR COST OF MEALS FOR ANY BREACH OF ANY E
17. o the battery near the front of the trailer NOT mount the E H brake actuator near the trailer axles or rear of the trailer Having the wire length longer than 25 feet may cause issues with performance and the normal operation of the unit Electrical Requirements It is critical that the BLACK power lead and WHITE ground lead from the tow vehicle to the input of the actuator are sized and properly terminated i e dedicated 25 40 amp circuit on the tow vehicle 12 gauge wire minimum 10 gauge wire is recommended to optimize performance Consult the SAE wiring guidelines for proper trailer electrical harness design Low temperature applications below O F require a 40 amp circuit The blue wire from the electric brake controller is connected through the trailer plug to the blue wire on the actuator The yellow wire from the E H brake actuator is connected to the cold side of the trailer emergency breakaway switch Under no circumstances should the actuator blue wire and the E H brake actuator yellow wire be connected together nor should sjuauiaJinbay 8911199 the blue wire ever be grounded The white wire is connected to the trailer ground and also connected to the tow vehicle ground through the trailer plug The black wire is connected to the 12V power line from the tow vehicle The black wire can also be connected to large on board coach batteries The black wire is connected to the small breakaway batt
18. on at all times The breakaway battery should be checked for proper charge level before every use Charging the Breakaway Battery The breakaway battery must be kept fully charged at all times in order to function properly Use only those breakaway battery kits that include a charging device Do not attempt to charge the breakaway battery directly from the tow vehicle without the appropriate charging device Test Electrical Operation 1 Attach the trailer to the towing vehicle Do not connect trailer plug to tow vehicle until step 2 is completed 2 Pull the breakaway switch The Dexter E H brake actuator should run If the unit does not run check breakaway battery condition and system wiring Reset the breakaway switch which will turn the unit off Note When the unit is running the motor will generate a hum that changes pitch as the unit builds pressure This is normal 3 Connect trailer plug to tow vehicle uoije1adg 291119913 1591 4 Turn the ignition switch on and turn the electric brake controller on Whenever the brake pedal is depressed the Dexter E H brake actuator should run with time based controllers Inertia type controllers will often require the vehicle to be moving in order for the Dexter E H brake actuator to come on by means of the brake pedal If the unit does not run check system wiring 5 Apply the controller manual slide The Dexter E H brake actuator should run and brake lights come on Test
19. ready to ship within 24 hours direct to you from the factory With dedicated customer support quick turnaround and a 30 day money back guarantee the Dexter Online Parts Store helps keep your trailer going Hub Components Brake Components D Suspension Components GENUINE Complete Hub Kits NIIS ACEN E Brake Assemblies amp Kits Brake Controllers amp Actuators Ready for Immediate Shipment Direct to Your Door Visit us online at www dexteraxle com 20 Notes 21 Notes 22 Notes 23 Genuine Dexter axles and components are available nationwide from our plant locations listed below or through our network of distributors Check our web site for the distributor nearest you Dexter Axle Dexter Axle 301 West Pearl Street 500 South 7th Street Fremont IN 46737 Albion IN 46701 Fax 260 495 1701 Fax 260 636 3030 Ph 260 495 5100 Ph 260 636 2195 Company Headquarters 2900 Industrial Parkway East Elkhart IN 46516 Fax 574 295 8666 Ph 574 295 7888 Dexter Axle 200 ah 27th Street Dexter Axle Fax 405 262 2056 199 Perimeter Road Monticello GA 31064 Fax 706 468 2966 Ph 706 468 6495 Ph 405 262 6700 DEXTER AXLE www dexteraxle com NO PART OF THIS CATALOG MAY BE REPRODUCED WITHOUT DEXTER AXLE S PERMISSION ALL PART NUMBERS DIMENSIONS AND SPECIFICATIONS IN THIS CATALOG ARE SUBJECT TO CHANGE WITHOUT NOTICE GEARED FOR
20. tional holes in the housing electrostatically painting or welding anywhere on the unit will damage the unit making it inoperable and will void the manufacturer s warranty Always remove the unit from the trailer before doing any welding repair or modifications to the trailer structure Connect the trailer brake lines to the actuator as follows 1 Remove the rubber or plastic plug from the 316 inverted flare brake port 2 Brake line must be compatible with DOT 3 DOT 4 or DOT 5 brake fluid 3 Flush existing brake system and lines until thy are free of any contaminants using DOT 3 DOT 4 or DOT 5 brake fluid prior to connecting to the Dexter E H brake actuator Installation Instructions 4 Connect the brake line from the trailer brakes to the 346 inverted flare fitting on the actuator Do not tighten the e brake line adapter more than the 22 Ft Lbs used at factory installation Fill the unit with DOT 3 DOT 4 or DOT 5 brake fluid to the bottom of the reservoir filler neck When putting the filler cap back on it should be turned clockwise until snug Always use new DOT 3 DOT 4 or DOT 5 brake fluid from a sealed container Never attempt to reuse old or dirty fluid Do not overfill the unit Take care to protect painted surfaces from contact with the brake fluid Wash off any spilled brake fluid Mount the emergency breakaway switch and emergency breakaway battery on the trailer as detailed in the instructio
Download Pdf Manuals
Related Search