User Manual
Contents
1. Drain the water tank after each drying please see Water tank Technical Specification EN Rated power input See type label Model code Type label is located behind the loading door 13 EN E Maintenance and cleaning Cover filter Lint and fibres released from the laundry to the air during the drying cycle are collected in the Cover Filter Such fibre and lint are generally formed during wearing and washing Always clean the filter after each drying process E You can clean the filter and filter area by vacuum cleaner Figure 2 To clean the filter 1 Take out the cover 2 a If the product s cover filter can be opened as shown in Figure 1 remove the filter by pulling it up and open the filter 2 b If the product s cover filter is as shown in Figure 2 remove the filter by pulling it up 3 Clean lint fibre and cotton raveling on the filter and in the filter housing by hand or with a soft piece of cloth 4 Close the filter and place it back into its seat El Clogging may arise on the filter surface after using your machine for some time if this occurs wash the filter with water and dry it before using again 14 EN g Solution suggestions for problems Problem Cause Explanation Suggestion Drying process Cover fi N er filter and filter drawer might Meshes of the filter may be clogged takes too much have not2. To cancel any selected program Press Start Pause Cancel button for about a duration of 3 seconds The Filter cleaning and Water tank warning LEDs as well as the 0 warning LED on the program follow up indicator will light up at the end of this period for reminding purposes As the inside of the machine will be excessively hot when you cancel the program while the machine is running activate the 12 EN ventilation program to cool it down A If the machine is stopped during any drying program and if the position of the program selection knob is changed an audio signal will be heard if the Cancel audio warning function is not selected The machine will not start even if the Start Pause Cancel button is pressed unless the program selection knob is returned to the initial program The paused program must be cancelled in order to change the drying program End of program The Filter cleaning and Water tank warning LEDs as well as the O warning LED on the program follow up indicator will light up at the end of the program The door can be opened and the machine becomes ready for a second cycle Press the On Off button to shut down the chine A 2 hour anti creasing program to prevent laundry from creasing will be activated if you do not take the laundry out after the program has come to an end Clean the filter after each drying please see Filter cleaning
3. at high temperature only for cotton laundry Thick and multi layered laundry E g towels linens jeans are dried in a way that they do not require ironing before placing in the wardrobe Ready to Wear Normal laundry E g tablecloths underwear are dried in a way that they do not require ironing before placing in the drawers Ready to Iron Normal laundry E g Shirts dresses are dried ready to be ironed E For further program details see Program Time Selection Table Main programs eAnti creasing A 2 hour anti creasing program to prevent laundry from creasing will be activated if you do not take the laundry out after the program has come to an end This program rotates the laundry in 60 second intervals to prevent creasing eVentilation Only ventilation is performed for 10 minutes without blowing hot air You can air your clothes that have been kept at closed environments for a long time thanks to this program to deodorize unpleasant odors eTimer programs You can select one of the 10 min 60 min 80 min timer programs to achieve the final drying level Dry the cotton laundry at high temperatures and synthetic and easy care laundry at low temperatures depending on the hye of the laundry You must press the Low temperature button for synthetics 10 EN Program selection and consumption table Approximate Capacity Spin speed in washing amount of Drying time kg machine rpm rema
4. stands level and firmly on the floor Do not use any tools to loosen the adjustable feet otherwise they can be damaged Never remove the adjustable feet from their housings 2 plastic pieces supplied along with the user manual prevent your machine from slipping on wet and slippery surfaces To install the plastic parts 1 Tilt your product to backwards 2 Fit the plastic parts on to the front adjustable feet Press on the plastic parts to snap them into their seating 3 Check the balance of your product again and readjust the adjustable feet if necessary Electrical connection Connect the machine to a grounded outlet protected by a fuse of suitable capacity as stated in the technical specifications table Our company shall not be liable for any damages that will arise when the machine is used on a circuit without grounding e Connection must comply with national regulations e f the current value of the fuse or breaker in the house is less than 13 Amps have a qualified electrician install a 13 Amp fuse e Power cable plug must be within easy reach after installation e The voltage and allowed fuse or breaker protection are specified in the Technical Specifications section e The specified voltage must be equal to your mains voltage e Do not make connections via extension cables or multi plugs e The main fuse and switches must have a contact distance of minimum 3 mm Z Damaged power cable must only be
5. the product must be cleaned by the qualified service personnel periodically Wrong connection of grounding conductor of the product can cause electric shock If you have any suspect about the grounding connection have it checked by a qualified electrician service representative or service personnel Do not reach into the machine when the drum is spinning Unplug the machine when it is not in use Never wash down the appliance with water 3 EN There is the risk of electric shock Always disconnect by unplugging from the mains before cleaning e Never touch the plug with wet hands Never unplug by pulling on the cable always pull out by grabbing the plug only Do not operate the machine ifthe power cable or plug is damaged e Never attempt to repair the machine yourself otherwise you will be putting your life and others lives in danger e For malfunctions that cannot be solved by following the information given in the safety instructions Turn off the machine turn off and contact an authorised service agent e Do not stop the dryer before the drying cycle comes to an end unless you will remove all laundry from the dryer fast in order to lay them and dissipate the heat e Remove the door of the drying compartment before decommissioning or disposing of the product e The final step of the drying cycle cool down cycle occurs without applying heat to ensure that the items are left at a temperature that will not dam
6. Dryer DV 7110 Read this manual prior to initial operation of the product Dear Customer We hope that your product which has been manufactured in modern facilities and passed through a strict quality control procedure will give you very good results We advise you to read through this manual carefully before using your product and keep it for future reference This User Manual will e Help you use your machine in a fast and safe way e Read the User Manual before installing and starting your product e In particular follow the instructions related to safety e Keep this User Manual within easy reach for future reference e Please read all additional documents supplied with your product Remember that this User Manual is also applicable for several other models Explanation of symbols Throughout this User Manual the following symbols are used Important safety information Warning for hazardous situations with regard to life and property Caution Warning for supply voltage Caution Warning for fire hazard gt pb D Caution Warning for hot surfaces LL Read the instructions E E Useful information Important information or useful hints about usage This appliance s packaging material is recyclable Help recycle it and protect the environment by dropping it off in the municipal receptacles provided for this purpose Your appliance also contains a great amount of recyclable material It is marked with this labe
7. age them e Fabric softeners or similar products should be used as specified by the fabric softener instructions e Underwear that contains metal reinforcements should not be placed in a dryer Damage to the dryer can result if metal reinforcements come loose during drying e Check all garments for forgotten lighters coins metal pieces needles etc before loading e At times when your dryer is not in use or after the laundry is taken out following the completion of drying process turn off by using the On Off button In cases when the On Off button is on while the dryer is energized keep the door of the dryer closed Intended use e This product has been designed for domestic use It should not be used for other purposes e Use the product only for drying laundry that are marked accordingly e Dry only those articles in your product that are stated in this manual e This product is not intended to be used by persons with physical sensory or mental disorders or unlearned or inexperienced people including children unless they are attended by a person who will be responsible for their safety or who will instruct them accordingly for use of the product Children s safety ectrical appliances are dangerous for the children Keep children away from the machine when it is operating Do not let them tamper with the machine e Packaging materials are dangerous to children Keep the packaging materials out of reach of c
8. been cleaned Wash with water time Cover filter and filter drawer might Laundry come out have not been cleaned oe of the filter may be clogged wet atthe end of ash with water Excessive laundry might have been drying loaded in Do not overload the machine It might have not been plugged in The loading door may be ajar Make sure that the machine is plugged in Machine does not Programme might have not been set Make sure that the loading door is switch on or the or the Start Pause Cancel button properly closed programme does ight have not been pressed Make sure that the programme has been not start Machine Childproof lock might have been set and it is not in Pause mode is not activated activated Deactivate the childproof lock 3 when set The condenser cover on the models Make sure that the condenser cover and with a condenser might not be closed the red lock is closed securely securely D Make sure that the loading door is ae The loading door may be ajar properly closed without any cause Electricity may be cut off Press Start Pause Cancel button to start the programme Dry only the laundry which is suitable for Laundry has drying in your machine after checking the shrunk become A programme suitable for the laundry labels on your clothes felted or type might have not been used Select a programme with suitable low de
9. cetone alcohol fuel oil kerosene stain remover turpentine paraffin and paraffin removers must be washed in hot water with plenty of detergent before being dried in the dryer Garments or pillows bolstered with rubber foam latex foam shower bonnets water resistant textiles materials with rubber reinforcement and rubber foam pads should not be dried in the dryer Do not use fabric softeners and anti static products unless they are recommended by the manufacturers of the fabric softener or the product This product must be grounded Grounding installation decreases the risk of electric shock by opening a path with low resistance for the electricity flow in case of a malfunction or failure Power cable of this product is equipped with a conductor and a grounding plug that allows for grounding the product This plug must be installed appropriately and inserted into a socket which is grounded in accordance with the local laws and regulations Do not install the product behind a door with a lock sliding door or a door that has a hinge against the hinge of the dryer Do not install or leave this product in places where it will be exposed to outdoor conditions Do not tamper with the controls Do not perform any repair or part replacing procedures on the product even if you know or have the ability to perform unless it is clearly suggested in the operating instructions or the published service manual Inside and exhaust duct of
10. h wet clothes and the result will be wet laundry after the drying process is over Laundry may be added or taken out as much as desired during a drying process but as this process will interrupt drying continuously it will extend the program duration and increase energy consumption Therefore it is recommended to add laundry before the drying program is started Child proof lock There is a childproof lock to prevent any program interruption due to the pressing of keys while the program is on The loading door and all keys except the On Off key on the panel are deactivated when the child proof lock is active In order to activate the childproof lock press on the Start Pause Cancel and Low temperature buttons simultaneously for 3 seconds To start a new program after the program is over or to interrupt the program the childproof lock should be deactivated To deactivate the childproof lock press the same buttons for 3 sec A th One of the LEDs on the program follow up indicator starts flashing when the child proof lock is activated E Child proof lock is deactivated when the machine is restarted by pressing the On Off button Ending the program through canceling The program which is selected first will keep on going even if the position of the program selection button is changed A new program can be selected and started after Program cancel is activated in order to change the drying program
11. he On Off button is pressed if the dryer is energizea Laundry suitable for drying in the achine Always follow the suggestions on the laundry labels Dry only the laundry having a label stating that they are suitable for drying in a dryer and make sure that you select the appropriate programme O X Y La Normal Low Suitable for Do not dry temperature temperature drier with drier Drying rying Hang without Oy ona ern tally spinning hanger Can be ironed _Canbe Do not iron with hot iron ironed with warm iron Laundry unsuitable for drying in the machine e Laundry items with metal attachments such as belt buckles and metal buttons can damage your dryer e Do not dry items such as woollens silk garments and nylon stockings delicate embroidered fabrics laundry with metal accessories and items such as sleeping bags in the dryer e Laundry made of delicate and valuable fabrics as well as lace curtains can be creased Do not dry them in the dryer e Do not dry items made of hermetic fibres such as pillows and quilts in the dryer e Laundry made of foam or rubber will be deformed e Do not dry laundry containing rubber in the dryer e Do not dry laundry exposed to petroleum oil combustible or explosive agents in the dryer even if they are washed beforehand e Overly wet laundry or laundry with dripping water must not be put into the dryer Items cleaned or washed with gasoil fuel oil d
12. hildren or dispose them by classifying according to waste directives e Do not allow children sit climb on or enter in the product e Children should be supervised to ensure that they do not play with the product e Close the loading door when you leave the area where the product is located m 4 EN 2 Installation Refer to the nearest Authorised Service Agent for installation of your product Preparation of location and electrical installation for the product is under customer s responsibility A installation and electrical connections must be carried out by a qualified personnel A Prior to installation visually check if the product has any defects on it If so do not have it installed Damaged products will cause risks for your safety Appropriate installation location Install the product in an environment which has no risk of freezing and is in a stable and level position e Operate your product in a well ventilated dust free environment e Do not block the air ducts in front of and under the product with materials such as long pile rugs and wooden bands e Do not place your product on a long pile rug or on similar surfaces e Do not install the product behind a door with a lock sliding door or a hinged door which can strike the product e Once the product is installed it should stay at the same place where its connections have been made When installing the product make sure that the rear wall of it does
13. ining minutes humidity C o me Ready to Wear Ready to Iron om n m A Ready to Wear Delicates Energy consumption values Approximate Energy Capacity Spin speed in washing amount of Programs consumption kg machine rpm remaining value kWh humidity ynthetics Energy Label standard program EN 61121 2005 All values given in the table have been fixed according to EN 61121 2005 Standard These values may deviate from the table according to the laundry type laundry spin speed environmental conditions and voltage fluctuations 11 EN Auxiliary function Low temperature This function allows for drying at lower temperatures and therefore saves energy Warning LED will light up when you select the function You must use this function when you dry your synthetic or delicate laundry Warning indicators Warning indicators may differ according to the model of your machine Filter cleaning A warning LED will light up to remind filter ganing after the program finishes If the filter cleaning warning LED lights up continuously please refer to Solution suggestions for problems Starting the Program 1 Press Start Pause Cancel button to start the program 2 Start Pause Cancel button will light up to indicate that the program has started Timer follow up indicator One of the lamps is on as far as program runs ON shows the approximate remaining time LEDs on the timer follow
14. l to indicate the used appliances that should not be mixed with other waste This way the appliance recycling organised by your manufacturer will be done under the best possible conditions in compliance EJ with European Directive 2002 96 EC on Waste Electrical and Electronic Equipment Contact your town hall or your retailer for the used appliance collection points closest to your home We thank you doing your part to protect the environment 2 EN 2960310556_EN 011211 1937 1 Important safety information This section includes safety information that will help protection from risks of personal injuries or materialistic damages Failure to follow these instructions shall cause any warranty and reliability commitment to become void General safety Never place the machine on a carpet covered floor otherwise lack of airflow beneath the machine may cause electrical parts to overheat This will cause problems with your machine If the power cable or mains plug is damaged you must call Authorised Service Agent for repair The product should not be plugged in during installation maintenance and repair works Such works should always be made by the technical service Manufacturer shall not be held responsible for damages arising from processes carried out by unauthorised persons Connect the product to a grounded outlet protected by a fuse of suitable capacity as stated in the technical specifications table Operate your prod
15. mum hose and pipe lengths are given in the table below Maximum length 1 elbow 45 1 elbow 90 1 elbow 90 short 1 wall passage Gl Each elbow and other passages should be subtracted from the maximum length stated above To connect a ventilation hose 1 Connect the air outlet hose to the hose spacer piece by turning it counterclockwise Make the hose passages as shown below Exhaust of humid air from the dryer into the room is inconvenient It may damage the walls and furniture in the room The ventilation hose can be routed outdoors via a window or it can be connected to the air outlet in the bathroom E Air outlet hose must be routed directly to the outdoors There must be a limited number of elbows as not to hinder ventilation To prevent water accumulation in the hose make sure that it is not folded on the floor Yon A A The ventilation hose should not be connected to the chimney of a stove or a fireplace 5 EN A Do not operate your product at the same time with heaters such as a coal or gas stove Airflow may cause the chimney to flare up Adjusting feet In order to ensure that your product operates more silently and vibration free it must stand level and balanced on its feet Front feet of your product can be adjusted Balance the machine by adjusting the feet 1 Loosen the feet by hand 2 Adjust the feet until the product
16. not touch anywhere tap socket etc and also pay attention to install the product at a place where it will stay permanently A Do not place the product on top of the power cable e Keep at least 1 5 cm distance to walls of other furniture Under counter installation e A special part Part no 295 970 0100 replacing the top trim must be provided and installed by the Authorised Service Agent in order to use the machine under a counter or in a cupboard It should never be operated without the top trim e Leave at least 3 cm of space between the side and rear walls of the product and the walls of the counter cupboard when installing your product under a counter or in a cupboard Mounting over a washing machine e A fitting device should be used between the two machines when installing above a washing machine The bracket Part no 296 280 0100 white 296 280 0200 grey must be installed by the Authorised Service Agent e Place the product on a firm floor If it will be placed on top of a washing machine the approximate weight of both machines may reach 180 kg when they are full Therefore the floor must be capable of carrying the load on it Ventilation hose and connection for products equipped with an outlet vent Ventilation hose allows exhaust air from inside the machine Vented dryer has 1 air outlet Stainless sheet metal or aluminum pipes can be used instead of a hose The pipe diameter should be minimum 10 cm Maxi
17. oading Open the loading door Place laundry items loosely into the dryer Push the loading door to close Ensure that no items are caught in the door 8 EN E selecting a Program and Operating Your Machine Control panel 1 2 3 4 o o o 6 5 1 Filter cleaning warning light 4 On Off button Warning light turns on when the filter is full Used to turn on and off the machine 2 Program follow up indicator 5 Programme selection knob Used to follow up the progress of the Used to select a programme current programme 6 Start Pause Cancel button 3 Low temperature Used to start pause or cancel the Used to dry in low temperatures programme V AUR Al AO A e r ry r il Cottons Synthetics tur entilation Spin Ready Readyto Filter On Off Start Child proof Tank Timer to iron wear cleaning pause lock full follow up cancel indicator 9 EN Preparing the machine 1 Plug in your machine 2 Place the laundry in the machine Press the On Off button Pressing the On Off button does not necessarily mean that the programme has started Press Start Pause Cancel button of the machine to start the programme Timer program selection Decide the appropriate time from the table below which includes drying temperature in degrees Select the desired time with the timer program selection button Extra dry Dry
18. replaced by a qualified electrician AM If the product is faulty it must not be operated unless it is repaired There is the risk of electric shock First use e To have the product ready for operation before calling the authorised service agent make sure that its location and power supply installations are appropriate If they are not call a qualified electrician to have any necessary arrangements carried out e Make sure that the power connections of the product are in accordance with the instructions given in relevant chapters of this manual Disposing of packaging material Packaging materials are dangerous to children Keep packaging materials in a safe place out of reach of children Packaging materials of your product are manufactured from recyclable materials Sort and dispose of them in accordance with recycled waste instructions Do not dispose of them with normal domestic waste Transportation of the machine 1 Unplug the machine from the mains 2 Remove the water drain if any and chimney connections 3 Drain water remained in the machine completely before transportation Disposing of the old machine Dispose of your old machine in an environmentally friendly manner Refer to your local dealer or solid waste collection centre in your area to learn how to dispose of your machine Before disposing of your old machine cut off the power cable plug and make the loading door lock unusable to avoid dange
19. rous conditions to children 6 EN El Initial preparations for drying TAMOS to be done for energy saving Make sure that you operate the product at its full capacity but pay attention to not exceeding it Spin your laundry at the highest speed possible when washing them Thus the drying time is shortened and energy consumption is decreased Pay attention to dry same types of laundry together Follow the instructions in the user manual for programme selection Make sure that sufficient clearance is provided at the front and rear side of the dryer for air circulation Do not block the grill at the front side of the product Do not open the door of the machine during drying unless necessary If you must certainly open the door pay attention not to keep it open for a long time Do not add new wet laundry during drying Lint and fibres released from the laundry to the air during the drying cycle are collected in the Lint Filter Make sure that you clean the filters before or after each drying In models with condenser make sure that you clean the condenser regularly at least once every month or after every 30 drying cycles In vented models follow the chimney connection rules in the user manual and pay attention to the chimney cleaning Ventilate the room where the dryer is located well during drying For power saving in models with lamps at times when your dryer is not in use keep the door closed if t
20. ry laundry solvents and other combustible or explosive materials as well as the items that are contaminated or spotted with such materials should not be dried in the product since they emit flammable or explosive vapor e Do not dry items cleaned with industrial chemicals in the dryer e Do not dry your unwashed laundry in the dryer e Items soiled with cooking oils acetone alcohol fuel oil kerosene stain remover turpentine paraffin and paraffin removers must be washed in hot water with plenty of detergent before being dried in the dryer e Garments or pillows bolstered with rubber foam latex foam shower bonnets water resistant textiles materials with rubber 7 EN reinforcement and rubber foam pads should not be dried in the dryer Do not use fabric softeners and anti static products unless they are recommended by the manufacturers of the fabric softener or the product dryer 1 2 times during drying process to separate bunched up laundry Following weights are given as examples Do not dry the underwear reinforced with metal parts in the dryer Ifthese metal reinforcements loosen and break during drying they will damage your dryer Preparing laundry for drying e Check all laundry items before loading them into the product to make sure that there are no lighters coins metal items needles and etc in their pockets or on any part of them Fabric softeners and similar products m
21. teriorated temperature for the laundry type to dry your clothes Drum lightning does not come on The machine might have not been Make sure that the machine is On for models started by using the On Off button Call the authorized service to replace the equipped with a Bulb may have blown bulb lamp Final Anti The 2 hour anti creasing programme creasing LED to prevent laundry from creasing might um off the machine and take out the flashes have been activated y Final Anti creasing LED is Program has come to an end i a the machine and take out the on The Drying LED A heat sensor failure has occurred Tur Machine ends the programme without n off the machine and take out the flashes heating laundry Call your authorized service eae Sl Filter might have not been cleaned Clean the cover filter Also for products equipped with a condenser Water may be full Water tank E warning LED is on a programme might be Drain the water in the water tank a is Filter drawer Condenser might have Clean the filters in the condenser filter on g not been cleaned drawer under the kick plate IN Call an authorized service agent if the problem persists 15 EN
22. uct at temperatures between 5 C and 35 C Do not use electrical devices in the product Do not connect the air exit of the product to the chimney holes which are used for the exhaust fumes of the devices operating with gas or other types of fuel You must provide enough ventilation in order to prevent gases exiting from devices operating with other types of fuels including the naked flame from accumulating in the room due to the back fire effect Always clean the lint filter before or after each loading Never operate your dryer without the lint filter installed Do not allow fibre dust and dirt accumulation around the exhaust exit and at adjacent areas Power cable plug must be within easy reach after installation Do not use extension cords multi plugs or adaptors to connect the dryer to power supply in order to decrease the risk of electric shock Do not make any changes on the plug supplied with the product If it is not compatible with the socket have a qualified electrician change the socket with a suitable one Items cleaned or washed with gasoil fuel oil dry laundry solvents and other combustible or explosive materials as well as the items that are contaminated or spotted with such materials should not be dried in the product since they emit flammable or explosive vapor Do not dry items cleaned with industrial chemicals in the dryer Do not dry unwashed items in the dryer Items soiled with cooking oils a
23. up indicator will also flash when the child proof lock is activated If more than one LED light up or flash concurrently it means there is malfunctioning or a failure please see Solution suggestions for problems Changing the program after the program has started You can use this feature to dry your laundry in a different program after your machine has started to run For example Press and hold the Start Pause Cancel button for about 3 seconds to select 80 minutes program instead of 60 minutes program Select the 80 minutes program by rotating the program knob Press Start Pause Cancel button to start the rogram The program which is selected first will go on even if the program selection button is moved and another program mode is selected while the machine is operating You must cancel the ongoing program in order to change the drying program See Ending the program through canceling Adding removing laundry in standby mode In order to add or take out laundry after the start up of the program 1 Press the Start Pause Cancel button to switch the machine to Pause mode Drying process will stop 2 Open the door at Pause position and close it again after adding or taking out laundry 3 Press Start Pause Cancel button to start the A program g Any laundry added after the drying process was started may cause the already dried clothes in the machine intermingle wit
24. ust be used in accordance with the instructions of the manufacturer of the relevant products All laundry must be spun at the highest spin speed that your washing machine allows for the laundry type Laundry may be tangled after washing Separate your laundry before placing them into your dryer Sort your laundry according to their types and thicknesses Dry the same type of laundry together E g fine kitchen towels and table cloths dry faster than the thick bath towels Correct load capacity L N Consider the information in the Programme Selection Table Always start the programme in accordance with the maximum load capacity fi Adding laundry to the machine more than the level shown in the figure is not recommended Drying performance will degrade when the machine is overloaded Furthermore your dryer and your laundry can be damaged Place your laundry into the drum loosely so that they will not get tangled fi Large pieces E g bed sheets quilt covers large tablecloths may bunch up Stop the Home articles A Cotton quit covers double 1500 Cotton quit covers single 1000 Bed sheets double 500 Bed sheets single 350 Large tablecloths 700 Small tablecloths 250 Tea napkins 100 Bath towels 700 Hand towels 350 Garments Be Blouses 150 Cotton shirts 300 Shirts 200 Cotton dresses 500 Dresses 350 Jeans 700 Handkerchiefs 10 pieces 100 T Shirts 125
Download Pdf Manuals
Related Search