Home
installation & maintenance manual for chssi two-post
Contents
1. Defects caused by ordinary wear and tear abuse misuse overloading accident including shipping damages improper maintenance and alterations not approved by the manufacturer or master lift distributor are specifically excluded The manufacturer amp master lift distributor reserves the absolute right to decline responsibility for repair work made or attempted by any company or person not associated with or approved beforehand by the manufacturer or master lift distributor WARRANTY LABOR IS NOT INCLUDED under warranty unless expressly approved by the manufacturer before the repairs are attempted or by your master lift distributor in writing CL 10 000 OHA 23 OF 25 Last printed 5 18 2006 10 27 00 PM COMPLETE HYDRAULIC SERVICE amp SALES INC 130 Commerce Park Drive Franklin IN 46131 888 736 5094 Toll Free 317 738 0555 Fax I would like to introduce you to COMPLETE HYDRAULIC SERVICE amp SALES INC We are a Hydraulic Lift Company specializing in Automotive Equipment as well as many other aspects of the Hydraulic Industry as you will see in our Sales Flyer enclosed This introduction comes to you as an invitation to be part of our Special Distributor Program in your area that will include a Protected Territory We can offer you Special Lift Prices as a Distributor at an UNBELIEVABLE 1 450 00 with a Power Unit With this Special Pricing you will Maintain a Protected Territory and FREE FREIGHT to you with
2. This is a 220 volt power unit Green is usually the ground wire Wire the overhead safety bar cut off switch in a series so when the switch is activated it will shout down the power to the hydraulic motor when you are raising a vehicle See FIGURE 4 for electrical connections NOTE Power Unit Wiring Choose One 1 If You Have The Power Unit With The Clear Tank Use Wiring Diagram 1 CL 10 000 OHA 10 OF 25 Last printed 5 18 2006 10 27 00 PM 2 If You Have The Power Unit With The Black Tank Use Wiring Diagram 2 CL 10 000 OHA SAFETY WIRING DIAGRAM Overhead Safety Switch Mounted to Overhead Safety Bar Bracket With Four Screws On Power Unit Side Approx 11 8 Cord Power Unit This Is Your 220 Volt AC Supplied With The Lift Motor Incoming Power Supply Off Of A 30 Amp Breaker Attach Black Wire To Either Of The 11 8 Overhead Safety See The Switch Cord Wires Detail Below On How To Wire Attach The White Wire Push Button To The Push Button Switch Switch See The Push Button Switch Detail Below Connect Either Wire From The Overhead Safety Switch Cord To The Black Wire On The Top Of The Push Button Switch Connect The White Wire From The Push Button 1 X 220 Volt Breaker Box To The White Switch Diagram 1 Wire 2 Terminal Down On The FIGURE 4 Switch Fixed Wiring To Motor From The Factory Connect One Motor Wire To The Terminal Marked C On The Switch Connect On
3. After getting both cables equally tight YOU SHOULD BE ABLE TO MOVE THE CABLES ABOUT AN INCH BACK AND FORTH WITH SLIGHT PRESSURE LIKE A FAN BELT OR A BANJO STRING raise the lift all the way up by pressing the up button on the power unit Do not bottom the lift out at the top by holding down on the switch Raise the lift off the locks by pushing the power button this will enable you to pull each release cable ring located at the bottom of both carriages See FIGURE 6 Pull down on the lowering valve handle on the power unit and lower the lift all the way to the floor Raise the lift again and listen for the clicking of the safety locks in each post Determine which side is slower and tighten the adjusting bolt on the opposite side carriage Remember to only tighten a few turns at CL 10 000 OHA 13 OF 25 Last printed 5 18 2006 10 27 00 PM a time until the locks click at the same time when raising the lift Cycle the lift up and down and listen to the safety latches clicking and make the proper adjustment Adjust until the carriages are with in a 4 of each other or the clicks are almost at the same time with each side When cables are adjusted properly they should be fairly tight CL 10 000 OHA 14 OF 25 Last printed 5 18 2006 10 27 00 PM Wd 00 12 01 9007 8 1 s jse q Sc HO SI 000 01 9 WANT HSVW THA OL NMOd AHL TINd ANV SMOOT AO AAO LAT ASIVA IE LA FINAL ASSEMBLY Check all bolts and
4. THE POWER UNIT IS NOT DESIGNED TO BE A LOAD HOLDING DEVICE NOT USING THE LOCKS WILL RESULT IN A PREMATURE FAILURE OF THE CYLINDERS PUMP AND OR CABLES AND CAN CAUSE SERIOUS PROPERTY DAMAGE PERSONAL _ INJURY FAILURE TO HEED THIS WARNING WILL RESULT IN IMMEDIATE TERMINATION OF YOUR WARRANTY MAINTENANCE SCHEDULE The following periodic maintenance is the suggested minimum requirements and minimum intervals accumulated hours or monthly period which ever comes sooner If you hear a noise or see any indication of possible failure cease operation immediately and inspect correct and or replace parts as required Following these maintenance procedures is the key to prolonging the useful life of your lift IF AT ANY TIME YOU RE NOT SURE OF THE SAFE OPERATION OF THE LIFT DISCONTINUE USING IT AND CALL YOUR DISTRIBUTOR FOR ASSISTANCE WARNING OSHA AND ANSI REQUIRE USERS TO INSPECT LIFTING EQUIPMENT AT THE START OF EVERY SHIFT THESE AND OTHER PERIODIC INSPECTIONS ARE THE RESPONSIBILITY OF THE USER DAILY PRE OPERATION CHECK The user should at least perform the following checks daily Daily check of safety latch system is very important the discovery of device failure could save you from expensive property damage lost production time serious personal injury and even death Check safety latches for free movement and full engagement with rack Check hydraulic connections and hoses for leakage Check snap rings at all rollers sheaves
5. Unit Hydraulic Fitting Straight Thread O Ring Branch Tee C5715 X 6 Overhead Safety Limit Switch 250V 5A Blue amp Yellow amp 4 Screws Over Head Safety Cable Clevis Screw 4 Flat Washers 3 Lock washers 1 Nut Sometimes Not Used Column Hydraulic Hose Clamps With 6 Screws Anchor Bolt 3 4 x 5 1 2 With Flat Washers amp Nuts Ve Bolts x 1 Ve Long For Overhead Cross Beam For Mounting To Column Extensions Extension Hydraulic Fitting Extra Sometimes Not Used 5 16 x 1 Mounting Bolts For Hyd Power Unit W 2 Flat Washers 1 Lock Washer amp 1 nut Rubber Grommets For Hydraulic Hose To Run Through For Extensions Arm Pins 1 vex 7 1 16 Long Hydraulic Hose Long Hydraulic Hose Short Black Truck Adapters Screw Up Style 2 Diam x 6 Long End End Carriage Lift Arms Lock Handle With Ball For Arm Restraints Sometimes Already Mounted on Carriage Hydraulic Power Unit 220 Volt 30 AMP Breaker w Manual Release Handle CHSSIMRH220V Overhead Safety Bar Padding For Shut Off Bar Approx 6 6 Overhead Safety Bar Approx 7 8 x 93 Overhead Safety Bar Wire To Wire Safety Switch To Power Unit Circuit Approx 11 8 3 8 x 33 8 Inch Wire Rope Equalizer Cables Sometimes Already Attached To Carriages W 5 8 Threads On 6 Long W 8 5 8 Nuts amp 4 5 8 Flat Washers Short 65 5 x 3 8 Hydraulic Hose W Female JIC 6 Straight Fittings Long 28 6 x 3 8 Hydraulic Hose W Female JIC 6 Straight Fittings 32 Top Column Extensions B
6. and on all screw up pads Check bolts nuts and screws and tighten Check wiring amp switches for damage Keep base plate free of dirt grease or any other corrosive substances Check for stress cracks in the concrete floor near the anchor bolts which if present could cause the anchor bolts to loosen and pull out of the floor Check Cables Cables keep both sides of the lift running equally allowing the safeties to catch together If one side of your lift is running ahead of the other most likely it is time to adjust your cables Follow this simple procedure te CL 10 000 OHA 21 OF 25 Last printed 5 18 2006 10 27 00 PM CL 10 000 OHA TROUBLE SHOOTING TROUBLE Pump Motor does not start Pump Motor operates but has no pressure Pump Motor operate low flow and or low pressure in raise mode in pressure mode Pump Motor operates but does not hold system Failure to lower Air in oil Motor does not run when energized Oil blows out the breather filter port Cylinder will not lift load Oil requirements CL 10 000 OHA CAUSE Improper electrical hook up Blown fuse Pump binding or stuck Motor thermal overload tripped Thermal overload in starter box Tripped Wrong rotation of motor Clogged inlet strainer cracking noise Relief valve leaking dirt on seat Release valve leaking Dirt on seat Release stem
7. manual A level floor is required for proper lift installation and operation DO NOT install this lift on any asphalt surface Only on concrete surface a minimum of 4 thick and 3 500 psi tensile strength with steel or fiber mesh reinforcement DO NOT install this lift over concrete expansion joints or cracks Check with your building architect DO NOT install this lift on an upper floor without written authorization from your building architect Should only be installed on basement floor DO NOT attempt to lift only part of a vehicle This lift is intended to raise the entire body of a vehicle only This will bend the arms and void the warranty DO NOT attempt to use the overhead beam to lift engines or any other parts out of a vehicle Doing so will bend the overhead beam and void the warranty NEVER lift any persons or vehicles containing persons This lift is designed to lift empty vehicles only TOOLS FOR INSTALLATION Concrete Rotary Hammer Drill with 3 4 inch Carbide Bit Rubber Hammer Chalk line Sockets and Open End Wrenches Ratchet Driver Vice Grips Measuring Tape Screwdrivers Torque Wrench Step Ladder Crain or Other Method to Raise Overhead Beam 4 Foot Bubble Level 12 Inch Crescent Wrench AW32 Non Foaming Hydraulic Fluid 4 gallons CL 10 000 OHA Last printed 5 18 2006 10 27 00 PM LIFT amp BOLT BOX CONTENTS PART DESCRIPTIONS Power
8. nuts to make sure they are tight Do not use an impact on concrete anchors Check all fittings for leaks If necessary make sure the arm lock restraints are engaging properly and smoothly If not tap the main lock forward or backward as needed with a rubber mallet to insure proper engagement on all 4 gears with the arm restraint locks Cycle lift up and down to insure carriages are synchronized Place a vehicle on the lift and raise until swivel pads are in contact with the frame of the vehicle Raise the vehicle up about 3 feet and lower until the tires touch the floor Keep raising and lowering the vehicle increasing the height each time until the vehicle is completely to the top This procedure pumps all the air from the system Now the lift is ready for use OPERATION Center vehicle left and right between the posts Position the swivel pads under frame of vehicle at the proper lifting points Push the up button and raise the lift until the swivel pads make contact with lifting points Check all swivel pads to make certain all adapters are making full and proper contact Raise vehicle approximately 2 feet and check the stability by rocking the vehicle from the bumper Raise vehicle to the desired height and lower on to the locking device Never leave the vehicle suspended off the locks To lower raise the lift off the locks by 2 then pull the lock release cable ring on each carriage downward releasing the lock release and lower slow
9. out of adjustment O ring missing or cut Relief valve setting too low Fitting loose Check valve leaking Dirt on seat Release stem out of adjustment O ring missing or cut Sticking release valves stem or out of adjustment Loose inlet connection or low oil level Leaky or blown oil seals in pump Siphon check does not seat Breaker thrown or fuse blown Motor thermal overload tripped Thermal overload in starter box Tripped Check micro switch Faulty wiring connections Oil overload Vehicle has been lowered too fast Seal damage to piston Oil leaking from cylinder front Use AW 32 Hydraulic Oil SOLUTION Rewire Replace fuse Remove flush or replace Let Cool 30 sec Push button reset Replace switch Call Electrician Rewire Clean strainer in solvent Flush seat or ball seat again Flush seat Re adjust stem setting Replace o ring Replace Tighten or replace fitting Flush seat Re adjust stem setting Replace o ring Replace Motor Replace stem and or cartridge Re adjust stem setting Tighten connection Add oil Replace oil seat Replace Reset or replace Wait for overload to cool Push button to reset Replace if necessary Call Electrician Remove to 2 3 full Restrict lowering with Manually controlled release Call factory for instruction Call factory for instruction Dexron III Automatic Transmission Fluid 22 OF 25 Last printed 5 18 2006 10 27 00 PM This limited warran
10. the cables much like a banjo string or a fan belt CL 10 000 OHA 25 Last printed 5 18 2006 10 27 00 PM EXTENSIONS amp OVERHEAD BEAM ASSEMBLY 11 8 Cord Down To Power Unit See FIGURE 4 For Detailed Wiring Diagram Slide Foam Rubber Pad Over Safety Switch Cross Bar Before Installation Of Mount Safety Switch To Bracket With Four Screws Supplied With Lift Install Pin And Retaining Clip To Hold Padded Bar FIGURE 2 CL 10 000 OHA Last printed 5 18 2006 10 27 00 PM CL 10 000 OHA EQULIZER CABLE CONFIGURATION DIAGRAM FIGURE 3 CL 10 000 OHA Last printed 5 18 2006 10 27 00 PM CONNECTING POWER UNIT amp HYDRAULIC HOSES Using the four 5 16 X 1 bolts mount the power unit to the main side column Install the TEE fitting with o ring end going into the power unit in the hole that is stamped For Pressure Connect the 3 8 65 2 SHORT hydraulic hose to the bottom of the tee fitting and run the hose down the side of the column and connect it to the end of the 90 degree elbow at the bottom of column Do not over tighten as you will crack the fitting Secure the hose to the column by using one of the 6 hose clamps and screws that is in your parts box Connect the 3 8 x 28 6 LONG hydraulic hose to the driver s side hydraulic fitting at the bottom of the column hydraulic cylinder outside the column Run the hose up the column and through the rubber grommet that is in your parts bo
11. ANTY IS NON TRANSFERABLE Company Name Owner Shop Manager Address Phone Fax City State Province Zip E mail COMPLETE HYDRAULIC SERVICE amp SALES INC 130 COMMERCE PARK DR FRANKLIN IN 46131 317 736 5094 bw THIS AUTOMOTIVE LIFT CONFORMS TO THE REQUIREMENTS PRESCRIBED BY ANSI B153 1 1981 Purchased From Purchase Date Address City State Office Phone Cell Phone CL 10 000 OHA 25 OF 25 Last printed 5 18 2006 10 27 00 PM FOLD IN HALF TAPE TOP APPLY STAMP amp MAIL Complete Hydraulic Service amp Sales Inc 130 Commerce Park Drive Franklin IN 46131 www completehydraulic com E mail sales completehydraulic com Complete Hydraulic Service amp Sales Inc 130 Commerce Park Drive Franklin Indiana 46131 ATTN Warranty Dept CL 10 000 OHA 26 OF 25 Last printed 5 18 2006 10 27 00 PM
12. E A WARRANTY FOR THE ADJUSTMENTS IF AT ANY TIME YOU RE NOT SURE OF THE SAFE OPERATION OF THE LIFT DISCONTINUE USING IT AND CALL YOUR DISTRIBUTOR FOR ASSISTANCE TESTING AND ADJUSTING LIFT With the power properly hooked up and hydraulic oil in the pump reservoir push the push button on the side of the motor to raise the carriages off the locks Release the push button and then pull the lock release cable under each carriage to release the locks Run the lift all the way up and down two more times to bleed all the air from the system While running the lift listen to the safeties clicking Each side should click simultaneously or with in a second of each other If they are not clicking together then adjust the cables to compensate by tightening the side opposite the one that is clicking last at the cable bolt at the top of the carriage on the same side Remember not to over tighten cables they should be firm much like a banjo string or a fan belt in a car CL 10 000 OHA 19 OF 25 Last printed 5 18 2006 10 27 00 PM GENERAL SAFETY INSTRUCTIONS ALWAYS make sure the lift is on the Locks before going under the vehicle NEVER allow anyone to go under the lift when raising or lowering Care must be taken as burns can occur from touching hot parts Do not operate equipment with a damaged cord or if the equipment has been dropped or damaged until a qualified serviceman has examined it To reduce the risk of fire do not operate equ
13. INSTALLATION amp MAINTENANCE MANUAL FOR C H S S l TWO POST CL 10 000 OHA VEHICLE LIFT 10 000 POUND MAXIMUM CAPACITY Catalog Number 5 18 2006 CL 10 000 OHA TABLE OF CONTENTS READ THIS BEFORE INSTALLING THE LIFT TOOLS FOR INSTALLATION LIFT amp BOLT BOX CONTENTS LIFT LAYOUT EXTENSIONS amp OVERHEAD BEAM ASSEMBLY INSTALLING SWING ARMS ELECTRICAL CONNECTION HYDRAULIC FLUID ADJUSTING CABLES FINAL ASSEMBLY MAINTENANCE TESTING AND ADJUSTING LIFT GENERAL SAFETY INSTRUCTIONS LIFT OPERATING INSTRUCTIONS MAINTENANCE SCHEDULE DAILY PRE OPERATION CHECK CL 10 000 OHA TROUBLE SHOOTING LIMITED LIFT WARRANTY WARRANTY ACTIVATION FORM DISTRIBUTED BY COMPLETE HYDRAULIC SERVICE amp SALES INC 130 COMMERCE PARK DRIVE FRANKLIN IN 46131 317 736 5094 Web www completehydraulic com E mail sales completehydraulic com CL 10 000 OHA Last printed 5 18 2006 10 27 00 PM READ THIS BEFORE INSTALLING THE LIFT Improper installation can cause injury or damage Read this installation and operation manual in its entirety before attempting to install the lift Manufacturer or Distributor assumes no responsibility for loss or damage of any kind expressed or implied resulting from improper installation or use of this lift Always use professional installation companies All persons using this equipment must be responsible qualified and carefully follow the operation and safety guidelines contained in this
14. a 20 piece order Please see the CL 10 000 OHA Lift Brochure we have enclosed detailing specifications of this particular lift or you can visit us on our website at www completehydraulic com This Lift comes with a 5 Year Structural Warranty and a 2 Year Warranty on the Hydraulics and Electrical We sell over 200 pieces per month of this style lift and we are looking for Distributors to increase this count to reach beyond all boundaries Payments and Open Credit Options are based on Credit Approval In addition we will soon have a 2 Post Base Plate Lift 4 Post Portable Lift and a Motorcycle Lift that will also be at an UNBELIEVABLE low price At this Low Low 1 450 00 Price you have the opportunity to increase the Profits of your Business I invite you to visit our Warehouse at any time or you may contact me personally for an appointment Toll Free 888 736 5094 24 hours a day 7 days a week to discuss this program You may also find our website helpful to familiarize yourself with our company at www completehydraulic com or E Mail me sales completehydraulic com Commercial Grade Lift Thank You fe Bown Randy Brown Chairman C E O Complete Hydraulic Service amp Sales Inc 130 Commerce Park Drive Franklin IN 46131 North American Division 888 736 5094 Toll Free CL 10 000 OHA 317 736 5094 Office 317 738 0555 Fax Warranty Activation Form ATTENTION MAIL TODAY TO ACTIVATE YOUR WARRANTY WARR
15. ad cross bar together on the floor and assemble the overhead safety shut off bar and switch as necessary to the overhead bar see FIGURE 2 Using a helper lift the overhead assembly to the top of the column extensions and bolt the overhead to the top of the extensions on each side with the opening of the overhead cross bar facing upward to enable you to run the cables and the hydraulic hose through the cross bar at the top without allowing the hose to rub against the cables After completing this level the 2 column and shim as necessary Drill the other 5 anchor holes as you did the 1 column and tighten the anchors to 75ft 108 Do not use an air impact or over tighten Manually lift both carriages on each column about waist high Let the carriages down allowing them to set on the lift safety lock stops Make sure they are at the same height and on the safety lock stops Check to insure the cylinders are properly seated into the cylinder hole in the base plate If they are properly seated the round part of the cylinder will be setting down on the steel flat and flush If the equalizer cables are not attached to the lift carriages do the following Take the 3 8 X 33 8 1 2 equalizer cables and place a 34 SAE flat washer over the threads and onto the cable Using vise grips and a socket tighten the cable nut half way down the threads See FIGURE 3 for proper cable routing Tighten the nuts on the threads until the proper slack is out of
16. e Power Wire From Your Push 220 Volt Breaker Box To The Center Button Terminal Marked N O On The Switch Switch Diagram 2 Connect The Other Power Wire From Last printe d 8 2006 IO Your 220 Volt Breaker Box To The Other Wire From The Motor CL 10 000 OHA HOSE ROUTING amp POWER UNIT Attach One End Of The 28 6 Hose To The Top Of Fitting In The Port Of The Power Unit And The Other End Of The Hose To The Fitting At The Bottom Of The Hydraulic Cylinder CL 10 000 OHA MOUNTING Run The Hose Through The Crossbar Eyelets And Overhead Beam To Ensure That The Cables Do Not Rub The Hose Attach One End Of The 65 5 Hose To The Bottom Of The Fitting In The Port N On The Power Unit And The Other End Of The Hose To The Fitting At The Bottom Of The Hydraulic Cylinder 7 V NOTE Should There Be A 90 Fitting in The Port Of The Power Unit Remove it and Replace It With The T Fitting In The Parts Bag FIGURE 5 Last printed 5 18 2006 10 27 00 PM HYDRAULIC FLUID In some cases remove the Red or Black hex head plug from the tank at the top where you are going to fill the tank with fluid Remove the black vent cap from the bottom of the tank as this is just screwed into a blind hole It will not leak out any oil that you may put in the tank Now screw the Red or Black plug into the bottom of the tank where you just removed the black ve
17. ipment in the vicinity of open containers of flammable liquids Adequate ventilation should be provided when working on internal combustion engines Keep hair loose clothing fingers and all parts of the body away from moving parts To reduce the risk of electrical shock do not use on wet surfaces or expose to rain Use only as described in this manual Use only manufacturer s recommended parts ALWAYS WEAR SAFETY GLASSES NEVER allow unauthorized personnel to operate lift ALWAYS know the gross weight of vehicle NEVER EXCEED CAPACITY OF LIFT 10 000 LBS NEVER use the lift to raise one end or one side of vehicle ALWAYS keep unqualified people away from area while loading unloading raising or lowering the lift NEVER allow anyone to ride in the vehicle while raising or lowering the lift ALWAYS keep the area clean and free of water grease and oil ALWAYS remove wheel chocks tools hoses etc before loading unloading raising or lowering the lift LIFT OPERATING INSTRUCTIONS Swing the front arms to the front and the rear arms to the rear Once arms are in position pull a car into the bay A general rule of thumb is to stop the car with the center of the wheelbase even with the center of the columns Swing the four arms under the vehicle and position the pads under the appropriate lifting points If you are not sure of the proper lifting points you should check the vehicle s service manual contact the vehicle ma
18. loss or damage of any kind expressed or implied resulting from improper installation or use of this product Read this installation manual in its entirety before attempting to install this lift LIFT STRUCTURE INSTALLATION Determine where the lift is to be installed Make sure there is enough room in front behind above and on the sides of the lift See FIGURE 1 for proper dimensions Layout with a chalk line your concrete floor to the proper layout you want and check for proper clearances Remove any loose Cables Hoses Part Boxes Hydraulic Power Unit etc if they are inside the columns or banded to the columns Remove the power unit box four swing arms from the lift Next remove the bolts holding the two columns together Remove the top column from the bottom Column out of the shipping crate and discard the steel CL 10 000 OHA Last printed 5 18 2006 10 27 00 PM LIFT LAYOUT CL 10 000 OHA 30 70 WALL OR OBSTACLE 9 Minimum 11 2 All measurements are approximate Overall height is 11 11 tall CL 10 000 OHA FIGURE 1 6 2006 10 27 00 __ _ Unbolt the 4 bolts at the end of each column and slide the overhead extensions out of the columns Turn the extensions 180 degree and rebolt the extension to the top of each column where you just unbolted them Place the opening of the extension to the inside just like the carriage opening There are 2 rubber grommets for the hydraulic hose to pa
19. ly After lowering rotate the swing arms back out of the way CL 10 000 OHA 16 OF 25 Last printed 5 18 2006 10 27 00 PM MAINTENANCE Lubrication Lubricate all nylon wear block corners inside each post with heavy duty bearing grease once every six months Lubricate chains every six months Anchor Bolts During first week of use check anchors daily Do not use an impact wrench After first week check once a month for the first six months Tighten as necessary Concrete Check concrete for stress cracks daily for the first two weeks of use as a precaution Thereafter check monthly Check all bolts and nuts every six months Hydraulic Oil If your lift will raise all the way to the top the hydraulic tank is full of Hydraulic Oil The hydraulic oil should be changed once a year along with cleaning the suction filter SAFETY LATCH ADJUSTMENT Do not make any adjustments on the lift or the cables If the safety latch in either column does not operate use the following procedure to adjust it Raise the lift until you can see the latch through the access hole in side of the column by removing the 2 screws and the cover Do not set lift on safety latch for this adjustment Allow the hydraulic system to hold the lift up during this adjustment Do not have a vehicle on the lift during this time Pull the latch forward with a screwdriver If the latch is not working during ascent tighten the adjustment bolt one full tur
20. n and test the latch and follow this procedure until the latch operates If the latch is not working during descent loosen the adjustment bolt one full turn and test the latch and follow this procedure until the latch operates Latch and or cable adjustments are normal maintenance and are not a warranty items CL 10 000 OHA 17 OF 25 Last printed 5 18 2006 10 27 00 PM AUTOMOTIVE LIFT SAFETY TIPS POST THESE SAFETY TIPS WHERE THEY WILL BE A CONSTANT REMINDER TO YOUR LIFT OPERATOR FOR INFORMATION SPECIFIC TO THE LIFT ALWAYS REFER TO THE LIFT MANUFACTURER S MANUAL YOUR DEALER OR INSTALLER Inspect your lift daily Never operate the lift if it malfunctions or if it has broken or damaged parts Repairs should be made with original equipment parts Operating controls amp safeties are designed to close when released Do not block them open or override them at any time Never overload your lift Manufacturer s rated capacity is shown on the serial tag affixed to the lift above the power unit Only trained and authorized personnel should do positioning of vehicle s and operation of the lifts Never raise vehicle with anyone inside it Customer or by standers should not be in the lift area during operation Always keep lift area free of obstructions grease oil trash and other debris Before driving vehicle over lift position arms and supports to provide unobstructed clearance Do not hit or run over lift arms adapter
21. nt cap Put the vented plug in the top after filling with oil Place a funnel into fill hole and fill the tank with one of the following fluids as below When the oil is about 1 inch from the bottom of the hole that is your full mark Refill the tank after running the lift up and down a few times to bleed out the air from the cylinders and hoses There is no bleeding procedure except for running the lift up and down 3 times Do not fill the tank with the lift up as you will overfill the tank and it will discharge out when you lower the lift Only top off tank with lift carriages on the floor When filling the Hydraulic Tank use the following fluids e AW 32 Hydraulic Oil e Dexron III Automatic Transmission Fluid This tank will hold approximately 16 quarts or 4 gallons when filled 1 inch below the vent plug ADJUSTING CABLES Place a pair of small or medium vise grips around the shoulder of the long threaded adjusting bolt on the cable to make any adjustments Use a deep socket to adjust the slack out of the cable Adjust tension to cables equally Do not over tighten Note If one of the cables is tighter than the other the carriage will go up uneven These should be tightened like a Banjo String or Fan Belt ADJUSTING amp SYNCHRONIZING THE CARRIAGES One of the most important things to remember is not to tighten down one side more than the other The key is to tighten one side a half dozen turns then the opposite side a half dozen turns
22. nufacturer Adjust the screw pads so they all hit their lifting points at the same time This will allow the car to be level when rising With the pads in their proper locations and no obstructions around the lift or vehicle you may now press the green button on the power unit to raise the vehicle Raise the vehicle so that the tires are 6 inches off the ground Walk to the back of the vehicle and push up and down on the bumper The vehicle will rock but should not at any time lose contact with the swivel pads If the vehicle is bouncing off the pads or feels at all unstable you should lower it back to the ground and reposition the arms amp pads to balance the load Repeat this process until the vehicle is completely stable When the vehicle is stable you many raise the lift all the way to the top Listen to safeties clicking and adjust if necessary CL 10 000 OHA 20 OF 25 Last printed 5 18 2006 10 27 00 PM THE PROPER OPERATION OF THE LIFT REQUIRES THAT ANY TIME YOU RAISE A VEHICLE TO WORK ON IT YOU MUST LOWER THE LIFT ONTO THE SAFETY LOCKS This is done by raising the vehicle to the desired height and lowering the lift by pressing the red lowering button until the arms stop on the next available lock To lower the vehicle you must first raise the lift off of the locks using the green button Then engage and hold the lowering handle until the lift is on the ground NEVER WORK UNDER OR NEAR THIS LIFT WITHOUT THE LOCKS BEING ENGAGED
23. olted Upside Down Inside Each Column W Pulleys Attached A Top Overhead Cross Beam Approx 61 34 Long B Top Overhead Cross Beam Approx 58 Long Columns 9 3 Tall 9 ADM AAC 1 1 1 2 N CL 10 000 OHA Last printed 5 18 2006 10 27 00 PM CL 10 000 OHA SPECIFICATIONS 11 11 2 9 m 1T 2 CL 10 000 OHA E H Last printed 5 18 2006 10 27 00 PM INSTALLATION amp OPERATION MANUAL Your lift is designed for many years of trouble free service when properly installed Please take the time to read this Installation Manual before proceeding INSTALLATION TIPS This lift is built from very heavy metal parts Use proper lifting techniques when lifting individual pieces Use plenty of help when moving lift pieces It is a good idea to wear work gloves to protect your hands This lift is designed to be installed on a minimum of 4 thick 3500 psi wire or fiberglass reinforced concrete Do not install this lift on asphalt wood or any other surface other than described A level surface is recommended Do not install this lift over expansion joints or cracks Check with qualified engineer or architect Do not install lift over a basement or on any level other than ground level i e second floor without written authorization from a building engineer or architect Improper installation can cause damage or injury Manufacturer will assume no liability for
24. or axle supports This could damage lift or vehicle Load the vehicle on lift carefully Position the lift supports to contact at the vehicle manufacturers recommended lifting points Raise the lift until supports contact the vehicle Check supports for secure contact with the vehicle Raise the lift to desired working height CAUTION If you are working under vehicle lift should be raised high enough for locking devise to be engaged Always set the lift down on the safety locks while your using the lift Note that with some vehicles the removal or installation of components may cause a critical shift in the center of gravity and result in raised vehicle stability Refer to the vehicle manufacturer s service manual for recommended procedures when vehicle components are removed Before lowering lift be sure tool trays stands jacks etc are removed from under vehicle Raise the vehicle off the locking devices before attempting to lower the lift and pull the safety lock rings under each carriage Before removing vehicle from lift area position lift arms and supports to provide a safe unobstructed exit CL 10 000 OHA 18 OF 25 Last printed 5 18 2006 10 27 00 PM NOTE IT IS THE CUSTOMER S OR THE END USER S RESPONSIBILITY TO MAINTAIN THE PROPER TENSON ON THE EQUALIZER OR OVERHEAD SAFETY RELEASE CABLES ASKING A QUALIFIED LIFT TECHANICAN TO RETURN IN THE FUTURE TO MAINTAIN THE CABLE ADJUSTMENTS AFTER THE LIFT IS INSTALLED WOULD NOT B
25. ss through in the parts box Install them in the top of each extension where the cut out area is Stand up the power unit column the one with the power unit bracket welded on it and position it inside the chalked lines to your chalked out dimensions It is recommended that this column be placed on the passenger side of the car but it can go on the driver s side if desired Keep in mind this is the post where your main electrical power supply will be connected and your hydraulic power unit is attached The column should face straight toward the other column Stand up the other column just opposite the main power unit column inside the chalk lines as shown as you see it in FIGURE 1 to your dimensions Using a tape measure measure from the back corner to the back corner of the base to ensure the columns are square to each other Adjust as necessary to obtain best fit and still provide good passage Now drill 5 holes in for 1 column and place the anchors as you go in the holes Do not tighten anchor bolts at this time Hammer drill all the way through the cement floor Using a level check the 1 column to insure it is level side to side and front to back Anchor the column using the 5 347 X 5 1 2 anchors that are provided If shimming is required in leveling the columns keep the shims as close to the anchors as possible by using shim stock Tighten the anchors 75ft lbs Do not use an air impact or over tighten Now bolt the 2 piece overhe
26. ty is transferable from the original retail purchaser No warranty exists until each piece of equipment is completely paid for It only applies to vehicle lifts and not to any other automotive related equipment that may have been purchased from Complete Hydraulic Service amp Sales Inc Any hydraulic cylinder on the lift found to be defective by the manufacturer and not from abuse within two 2 years from the date of the original invoice will be replaced Power units are covered for defects in workmanship for two 2 years from date of original invoice Any misuse of power unit will void this warranty For power unit warranty repairs the original purchaser needs to provide the following information 1 Date code of the power unit 2 Serial number of the power unit and 3 Model number In cases of approved Power Unit replacements you will be sent a replacement power unit with a call tag It is the original purchaser s responsibility to properly drain and box the defective unit tag it and call UPS to pick it up No charges will be billed to you for return freight for authorized repairs Failure to follow these procedures will void the power unit warranty Any other lift part other than hydraulic hoses power units or parts made by other manufacturers which is found by the factory to be defective and which was not found to have been abused will be repaired or replaced at the manufacturer s or master lift distributor s option
27. x you should have already installed the rubber grommet into the overhead cross beam for the hose to run through Run the hose across the cross beam going through the round welded guides Go across the entire overhead through the rubber Grommet on the Power unit side and down to the Tee fitting at the power unit and tighten the fitting Secure the hydraulic hose with the screws amp hose clamps provided on both sides of the columns See FIGURE 5 for hose layout and routing the Power Unit INSTALLING SWING ARMS Locate the 4 swing arms and swing arm pins The pins are in the misc parts box Take one of the arms and insert it over the hole in the carriage torsion tube Line up the holes and insert the pin Repeat for the three other arms Asymmetrical lift owners the short arm with the crook in it goes closest to the front of the vehicle as your pulling into the lift ELECTRICAL CONNECTION IT IS BEST TO HAVE A QUALIFIED ELECTRICIAN HOOK THE MAIN ELECTRICAL POWER CONNECTION TO THE POWER UNIT AND THE OVERHEAD SAFETY CUT OFF BAR SWITCH FOLLOW LOCAL CODES IN YOUR AREA The electricity is to be hooked up at the power unit There are 2 wires inside the electrical box on the motor Make a connection with the 2 loose wires inside the motor box with 2 wires from your main power supply to the lift The power supply to the lift should be 220 Volt with a 30 amp breaker Attach the ground wire to the back of the box with the screw if it is not connected
Download Pdf Manuals
Related Search
Related Contents
USER MANUAL iOS User Manual charon-axp/sma Condicionador de Ar Tipo Tower PDFダウンロード 5.2 - PPS - University of California, Santa Cruz Havis-Shields C-3090 User's Manual SPECIFICATIONS CONTENTS: OWNER`S User`s Manual - Observatorio Astronómico Nacional de San Pedro Copyright © All rights reserved.
Failed to retrieve file