installation manual for rock krawler suspension, inc. jk
Contents
1. Please note they require welding It is not critical that they be done immediately for street use but for off road use this is required A inch fillet weld is preferred for this bracket This will make your OEM track bar mount much more rigid for off road abuse Please note the extra hole is there just in case you would like to relocate your steering stabilizer on top of the tie rod instead of letting it hang down below 15a For the 2 5 and 3 5 Systems Only 5 5 Systems skip this step Install the supplied front track bar Set the track bar to the specified length from the tables on page 4 or 5 for your given application Balance the amount of thread showing past the jam nuts Then install the track bar The bushing end goes at the frame and the heim joint end goes to the axle end Secure the frame and axle connections with the OEM hardware Please note the bend in the track bar is for clearance for the differential and the orientation of the track bar is controlled by locking the jam nut of the flex joint at the frame connection Once the orientation of the bar is set then orient the heim joint at the axle connection to have maximum amount of movement at the axle and lock the jam nut in place Using loctite on the jam nuts should prevent them coming loose and damaging the thread integrity of the track bar Do not allow more than 2 of threads to show past the jam nut for final adjustment 15b For the 5 5 Systems Only 2 5 and 32. 2 Door 19 50 3 5 X System Rear Upper Control Arm 4 Door 18 15 16 3 5 X System Rear Upper Control Arm 2 Door 19 375 3 5 X System Rear Upper Control Arm 4 Door 18 15 16 If you got a 5 5 System 5 5 Front Track Bar Assembled Length 32 625 5 5 Rear Track Bar Assembled Length 40 00 5 5 Front Lower Control Arm Assembled Length 23 250 5 5 Front Upper Control Arm Assembled Length 19 9 16 5 5 X or X System Rear Lower Control Arm 2 Door 21 00 5 5 X or X System Rear Lower Control Arm 4 Door 21 50 5 5 X System Rear Upper Control Arm 2 Door 19 625 5 5 X System Rear Upper Control Arm 4 Door 19 00 5 5 X System Rear Upper Control Arm 2 Door 19 50 5 5 X System Rear Upper Control Arm 4 Door 18 15 16 Please Note All Control Arms Torque Arms Track Bars and Triangulated 4 Link Assemblies come pre assembled but they require final adjustment as specified in the directions above ROCK KRAWLER Start with the Front End 1 Make sure vehicle is still on a level hard working surface Block the rear wheels so the vehicle cannot move and make sure the emergency brake is applied Raise the front of vehicle and support with safety jack stands Locate jack stands on the frame in front of the axle 2 Remove the front rims and tires 3 Support the front axle housing using a hydraulic floor jack 4 Remove the front shock
3. 25 ROCK KRAWLER Torque all 14mm and 9 16 bolts to 90 100 ft lbs Torque all 12mm and 1 bolts to 75 80 ft Ibs Torque all 10mm and 3 8 bolts to 30 35 ft lbs Please note If your steering wheel is off at all the ESP will be activated This will be corrected once the vehicle is aligned by a certified Jeep dealership A note about jam nuts and the consumer s responsibility The installer is the person or persons initially responsible for the proper setup of the suspension system and or components and the initial tightening of the jam nuts The consumer or vehicle owner is the person or persons responsible for maintaining the jam nuts tight Failure to do so will result in the rapid deterioration of the threads in the control arm and will impose a cause for concern for the occupants of the vehicle Failure to comply with the warnings headed in the directions regarding the amount of threads showing past the jam nut will also cause the same cause for concern for the occupants of the vehicle All of the above items are the responsibility of the vehicle owner and or installer If a threaded section of a component is bad it will show itself defective immediately Threads that fail over time are due to improper maintenance of jam nuts and can be proven very easily Thread sections not properly maintained or setup are not covered under warranty This is the end user and installer s responsibility Servicing of the Rock Krawler Rebuild able Joints is u
4. 5 Systems skip this step Install the supplied front track bar Set the track bar to the specified length from the tables on page 4 or 5 for your given application Balance the amount of thread showing past the jam nuts Then install the track bar The bushing end goes at the frame and the heim joint end goes to the new mounting hole in the track bar bracket at the axle Secure the frame connection with the OEM hardware and the axle connection with the supplied 14mm x 90mm bolt 14mm washers and 14mm nylok nuts Please note the bend in the track bar is for clearance for the differential and the orientation of the track bar is controlled by locking the jam nut of the flex joint at the frame connection Once the orientation of the bar is set then orient the heim joint at the axle connection to have maximum amount of movement at the axle and lock the jam nut in place Using loctite on the jam nuts should prevent them coming loose and damaging the thread integrity of the track bar Do not allow more than 2 of threads to show past the jam nut for final adjustment 16 Install the Rock Krawler front springs making sure the end of the spring sits properly in the spring buckets on the axle 17 For X Factor and X Factor Plus Systems only Flex Entry Level Stock Mod and Max Travel Kits Skip this step install the supplied front spring retainer clips by placing the clip on the bottom coil mark the hole in the spring pad and then drill a 10mm hole Then
5. arm if it is still in good condition C4 Grab the jam nut supplied with the new drag link kit from Rock Krawler and thread it all the way up one of the tie rod ends Insert it into the new drag link and show approximately 1 2 of thread past the jam nut when inserted Please note this tie rod end will be going to the knuckle connection as shown below 11 ROCK KRAWLER P S Knuckle Connections C5 Measure the OEM drag link operating length from center of ball joint to center of ball joint Mark the length for that is where you are going to start with your new assembly C6 Attach the quick adjuster to the newly supplied tie rod and thread it on all the way Put the other OEM tie rod end into the other end of the quick adjuster and thread it in all the way as well C7 Set the newly supplied drag link to the measured length of the original one by adjusting the quick adjuster only Do not adjust the other tie rod end that will be at the axle connection unless it is absolutely necessary C8 Insert the ball joint ends of the tie rods into the knuckle connection and pitman arm connection in the same orientation as the OEM units Place the supplied 5 8 flat washer on top prior to threading on the nut C9 Torque the nuts down 90 to 100 ft lbs C10 Be sure to do your best to center the steering wheel using the turn buckle style quick adjuster in the drag link then lock the jam nut using the wrench flat sections of the drag link for
6. best to have the front sway bar disconnected This will allow your suspension to do its intended function Our suspension will give your vehicle unmatched articulation which will give you traction to keep your vehicle moving Let the system do the work This will save on vehicle abuse 2 For Mud especially sloppy mud it is best to have the front sway bar connected This will limit the suspension travel which is better for mud 3 For Highway driving it is best to have the front sway bar connected This will give you the on highway ride and handling characteristics you expect If you choose otherwise you do so at your own risk Reference Lengths If you got a 2 5 System 2 5 Front Track Bar Assembled Length 32 9 16 2 5 Front Lower Control Arm Assembled Length 23 1 8 2 5 Rear Lower Control Arm 2 Door 19 5 8 2 5 Rear Lower Control Arm 4 Door 20 1 8 ROCK KRAWLER If you got a 3 5 System 3 5 Front Track Bar Assembled Length 32 625 3 5 Rear Track Bar Assembled Length 39 75 3 5 Front Lower Control Arm Assembled Length 23 125 3 5 Front Upper Control Arm Assembled Length 19 375 3 5 Flex System Rear Lower Control Arm 2 Door 19 50 3 5 Flex System Rear Lower Control Arm 4 Door 20 00 3 5 X or X System Rear Lower Control Arm 2 Door 21 00 3 5 X or X System Rear Lower Control Arm 4 Door 21 375 3 5 X System Rear Upper Control Arm
7. ground check that the front axle is centered under the vehicle If the axle is not centered adjust rod end krawler joints to center the axle If the axle is centered tighten all hardware to proper torque spec Do not allow more than 1 2 of threads to show past the jam nut for final adjustment 14 FROCK KRAWLER Now Lets Start the Rear Assembly 1 Park vehicle on a level hard working surface Raise rear of vehicle and support with safety jack stands Locate jack stands on the frame behind the rear axle 2 Remove the rear rims and tires 3 Support the rear axle using a hydraulic floor jack 4 Remove the rear shocks and save the hardware for reuse 5 Remove the rear sway bar links 6 Lower the rear axle and remove the rear coil springs 7 Remove the rear track bar and discard it save the hardware for reuse 8 For all systems other than Entry Level Entry Level and Stock Mod Skip this step remove the rear lower control arms using and save the hardware for reuse 9 For all X Factor and X Factor Plus Kits Flex Entry Level Stock Mod and Max Travel Kits Skip This Step remove the factory rear upper control arms and discard them save the hardware for reuse 10 Install the rear track bar relocation bracket as shown below Attach the bracket using the OEM bolt with the supplied 7 8 O D x 9 16 I D x 1 625 Long crush sleeve on the inside of the OEM lower track bar mount as shown below Drill a 2 hole through th
8. it contacts the offset tool Then weld it in place on front and back as shown below 17 ROCK KRAWLER Welding the rear cradle 18 POCK KRAWLER 11c Install the rear shock relocation brackets The brackets have a hole that aligns them off the rear sway bar link mount as shown below then weld them in place as shown below Be sure to prep the surfaces properly prior to weld and after the weld operation is completed be sure to apply a durable finish of your choice Now you can trim off the remaining of the lower control arm mounts that hand below the rear shock relocation bracket Installing the Bracket Final Ground Clearance Improvement 12 For X Factor Plus Systems Only All other system omit this step install the rear upper control arm Set the rear upper control arm to the specified length for the appropriate lift height from the tables on pages 4 and 5 Bolt the rear upper control arm in place using the supplied 14mm x 90mm bolts washers and nylok nuts The rear cradle has adjustable anti squat holes built into it For all mid arm kits it is recommended that you start out on the lowest hole bottom hole in the cradle then adjust to your liking and driving style Please note Tightening the jam nut for the frame connection is difficult when the arm is in the vehicle It is recommended that this jam nut be loctited and tightened outside the vehicle Do not show more than 5 8 of thread past the jam nut on either joint 19 FOC
9. secure the spring clip with the supplied 10mm x 35 mm bolt and nylok nut This should prevent your springs from rotating out of the spring pockets on the axle should they experience a ROCK KRAWLER no load condition off road The Driver s Side is shown below and the spring clip sits behind the axle as shown On the Passenger Side it is just the opposite The spring clip sits on the front side of the axle Pd 18 Install the front shocks using original hardware 19 Install the front sway bar disconnects as shown below For the top mount use the supplied 2 x 2 5 bolt 595 long spacer and nylok nut to make the connection Please note the shoulder of the spacer goes against the sway bar itself For the bottom connection attach the 1 2 x 2 0 long bolt with cross drilled hole to the factory sway bar link bracket Secure the bolt with the supplied 1 2 jam nut For connecting the bottom end of the sway bar link to the bottom bolt there are two options supplied with each kit If you do not have the automatic sway bar disconnect feature you can secure the bottom end of the sway bar link with the 2 nylon washers on either side of the rod end and secure it with the pin If you do have the automatic sway bar disconnect feature you can simply secure the bottom rod end with the supplied 2 nylok nut Please note on some sway bars you may have to reem out the hole to 2 with a 2 drill bit Top Sway Bar Connection Bott
10. spacers and 2 nylok nuts as shown below Please note the shoulder of the spacer goes towards the sway bar and the bottom mounting bracket away from the rod end 22 ROCK KRAWLER Jy SOI Ob a aA VARAI JUCA 21 For X Factor and X Factor Plus Kits Entry Level Flex Stock Mod and Max Travel Kits Skip this step remove the factory rear brake lines and install the supplied stainless steel brake lines Now you can go ahead and blead the brake system per the JK service manual 22 Remove the wire hanger for the rear emergency brake cable and route them to have as much slack as possible 23 Install the rear shocks Shocks should be non expanded can shocks with a shock body of no more than 2 in diameter or there is a risk of the rear shock contacting the rear track bar relocation bracket 24 Install rear rims and tires raise vehicle off jack stands and lower vehicle to the ground Before Hitting the Pavement or the Trails be sure to make sure the control arms are oriented properly all spherical joints heim joints and Krawler Joints are oriented correctly to allow for maximum movement without bind and all Jam Nuts are Tight Make sure the axles are properly centered pinion angles are correct there is proper slack in ABS lines all lines are properly routed so you never run into an issue on or off the road Go back over all your hardware and make sure each connection is tight and follow the following torque specs
11. INSTALLATION MANUAL FOR ROCK KRAWLER SUSPENSION INC JK MID ARM SYSTEMS FIFTH EDITION 07 01 10 ROCK KRAWLER Dear customer Thank you for purchasing the best system on the market for your Jeep Vehicle We are sure you will be happy with this system after your installation is complete Please take your time during the installation and be sure to do it correctly Completely read the directions before starting your installation so you know what to expect Remember your personal safety depends on it Should you have any questions during this installation feel free to give our tech line a call 518 270 9822 and we will be happy to help you Note BE SURE TO CHECK ALL FASTENERS FOR PROPER TORQUE BEFORE TEST DRIVE RECHECK AFTER 500 MILES AND BE SURE TO CHECK PERIODICALLY Warning Read and understand all instructions warnings and safety precautions in these instructions and your owner s manual before attempting to install these components Caution Proper installation of Rock Krawler Suspension Inc Products requires knowledge of recommended procedures for disassembly assembly of OE vehicles and components Access to OE shop manuals and special tools are required Attempting to install this kit without knowledge of these procedures may affect the safety of your vehicle and or the performance of these components Rock Krawler Suspension Inc strongly recommends that this system be installed by a certified mechanic with of
12. K KRAWLER 13 For X Factor Systems Only All other systems omit this step completely install the rear upper control arms setting the control arms to the specified length from the tables on pages 4 and 5 for the appropriate lift height using the OEM hardware Do not show more than 2 of thread past the jam nuts 14 For all Non Entry Level Systems Entry Level and Stock Mod Skip This Step All other systems install the rear lower control arms with Krawler Joint Spherical Joint at the axle mount and the Monster Bushing on the OEM frame mounts Use the OEM hardware for installation Set the front lowers to the specified length in the control arm table on page 4 or 5 for your given application Do not allow more than 5 8 of threads to show past the jam nut for final adjustment Helpful Hit Orient the Krawler Joint for maximum amount of movement then add red loctite and tighten down the jam nut on the joint prior to installing the arm since it is difficult to get at the jam nut when it is in the vehicle Remember it is a 1 14 Jam nut so do not be afraid to over tighten it In other words put something behind it for God Sakes Also note The bend in the arms is for improved ground clearance 15 For Entry Level Flex Systems Stock Mod and Max Travel Kits only X Factor and X Factor Plus Systems omit this Step Reinstall the factory rear track bar in the newly supplied rear track bar bracket with the supplied 14mm x 90mm bolt washers an
13. d nylok nuts 16 For all systems other than Entry Level Flex Systems Stock Mod and Max Travel Entry Level Flex Stock Mod and Max Travel kits Skip this Step Install the supplied rear track bar Set the track bar to the specified length from the tables on page 4 or 5 for your given application Balance the amount of thread showing past the jam nuts Then install the track bar The bushing end goes at the frame and the heim joint end goes to the new mounting hole in the track bar bracket at the axle Secure the frame connection with the OEM hardware and the axle connection with the supplied 14mm x 60mm bolt 14mm washers and 14mm nylok nuts Please note the bend in the track bar is for clearance for the differential and the orientation of the track bar is controlled by locking the jam nut of the flex joint at the frame connection Once the orientation of the bar is set then orient the heim joint at the axle connection to have maximum amount of movement at the axle and lock the jam nut in place Using 20 FOCK KRAWLER loctite on the jam nuts should prevent them coming loose and damaging the thread integrity of the track bar Do not allow more than 1 2 of threads to show past the jam nut for final adjustment 17 For X Factor and X Factor Plus Kits Entry Level Flex Stock Mod and Max Travel Systems Skip this Step Install the spring correction degree shims under the rear coils The thick part of the shim goes towards the rear of the v
14. e inside of the factory bracket where the supplied hole in our bracket is and secure that position with the supplied 2 x 1 25 long bolt washers and nylok nut Drill a second 10mm hole through the top of the OEM bracket where the existing hole is in out new bracket and secure it with the supplied 10mmx35mm bolt and 10mm nylok nut Please note Our bracket wings cup the OEM rear axle tubes This is due to the fact that the OEM factory rear track bracket is so weak It is required before your first off road adventure with your JK that these wings be welded to the axle tubes This will prevent any failures of the rear track bracket assembly 15 ROCK KRAWLER 11 For X Factor Plus Systems Only All other system omit step 11 completely perform the following 11a Install the independent third link upper control arm mount The bracket spans the two rear upper frame cross members and aligns off the holes in each cross member as shown below Then clamp the bracket with the holes aligned to the cross members and weld it in place Be sure to properly prep the surfaces and apply a durable finish after the weld operation is completed 16 ROCK KRAWLER 11b Install the weld on rear cradle Center the cradle left to right on the axle Make sure the third link mount on the top is open to the front so the cradle is oriented properly Then hold the offset tool as shown below up against the differential cover and rotate the cradle back until
15. ehicle as shown below Please Note A nice simple way to retain the rear coils to the axle is to use a hose clamp up through the center hole of the spring pad and clamp it around the bottom winding of the coil spring This is simple and cost effective 18 Install the Rock Krawler rear coil springs 19 For X Factor and X Factor Plus Kits Entry Level Flex Stock Mod and Max Travel Kits Skip this Step Using the 4 supplied 3 8 thread former screw and 3 8 washers we will now be relocating the rear sway bar mounting brackets one inch Simply unbolt the rear sway bar mounting brackets from the frame measure one inch back from each mounting hole mark the new holes locations and drill them out to 5 16 Then put some WD 40 or lubricant on the newly supplied thread former bolts and screw them in the holes Please be sure to make sure to start them straight This will make the process easier Torque them down to 25 to 30 ft lbs 21 ROCK KRAWLER 20 Installing the rear extended sway bar links a For Entry Level Flex and Max Travel Kits Stock Mod X Factor and X Factor Plus Systems Omit this Step Simply install the supplied rear sway bar links on the outside of the OEM brackets and Sway Bar These are standard bushing ends b For X Factor and X Factor Plus Kits Entry Level Flex Stock Mod and Max Travel Kits Skip this Step Install the supplied rear sway bar links using the supplied 1 2 x 2 0 bolts 330 long shoulder
16. f road experience Warning Rock Krawler Suspension Inc does not recommend combined use of suspension 2 ROCK KRAWLER lifts body lifts or other lift devices Combined use of lifts may result in unsafe and unexpected handling characteristics Also many states now have laws restricting Vehicle lift bumper heights and other alterations Consult local laws to determine if your proposed alterations including installation of this system comply with your state laws Caution Rock Krawler Suspension Inc recommends the use of locktite on all hardware unless noted otherwise Warning Properly block and secure vehicle prior to installation Warning Always wear safety glasses when using power tools Warning Rock Krawler Suspension Inc does not condone or authorize the use of any other suspension components with its products Should Rock Krawler Systems or components be installed in junction with other products or not per the provided instructions Rock Krawler Suspension Inc s warranty is void and is not to be held accountable for any resulting actions Warning The use of limiting straps 1s recommended to avoid possible damage from over extending the suspension of your vehicle ROCK KRAWLER Items you will also need other than standard tools Red locktite grease jack and jack stands Helpful hint Do not tighten connections until assemblies are installed in entirety Driving Tips 1 For Rock Crawling it is
17. ms install the front lower control arms with Krawler Joint Spherical Joint at the axle mount and the Monster Bushing on the OEM frame mounts Use the OEM hardware for installation Set the front lowers to the specified length in the control arm table on page 4 or 5 for your given application Do not allow more than 5 8 of threads to show past the jam nut for final adjustment Helpful Hit Orient the Krawler Joint for maximum amount of movement then add red loctite and tighten down the jam nut on the joint prior to installing the arm since it is difficult to get at the jam nut when it is in the vehicle Remember it is a 1 14 Jam nut so do not be afraid to over tighten it In other words put something behind it for God Sakes Also note The bend in the arms is for improved ground clearance See below for proper orientation FOCK KRAWLER 13 For all 5 5 Systems 2 5 and 3 5 Systems omit this step install the front track bar bracket Grab the front track bar bracket and secure it in position as shown below using the OEM lower track bar hardware Then drill out the other two holes in the OEM bracket through the supplied bracket with a 2 drill bit as shown below Then finish securing the new bracket with the supplied 2 x 3 bolts 2 washers and 2 nylok nuts a Ld FOCK KRAWLER 14 For all 5 5 Systems 2 5 and 3 5 Systems omit this step Install the supplied front track bar gusset bracket as shown below
18. nique from the rest of the industry We supply our joints with a plug or socket head cap screw in them Simply remove the plug and put in some 3 in 1 oil which is preferred or WD 40 the reinstall the plug We do this for many reasons The first is our joints are extremely tight and will not take grease very easily Second in the off road environment grease attracts much more dirt and debris than it is worth causing joints to wear quickly Grease would take forever to lubricate our joints since they are so tight 3 in 1 or WD 40 is clean simple and lubricates quickly If worse comes to worse simply spray down the outside of our joints liberally with WD 40 or MPL and call it a day It is a requirement that your vehicle be taken to a Jeep Dealership for an alignment The Jeep Dealer should align the vehicle and also verify all ESP ABS connections are in good working order or trouble may arise The routing of ABS ESP and Brake Lines is your responsibility Do so carefully Good Job Your installation is complete Now go out and enjoy your vehicle 24
19. om Sway Bar w o Auto Disco Bottom Sway Bar w Auto Disco FOCK KRAWLER 20 For the 5 5 Systems Only 2 5 and 3 5 Systems skip this step Disconnect the drag link from the OEM pitman arm and the passenger side knuckle Discard the OEM Drag Link since you will be installing the new H D Rock Krawler Drag Link Assembly a Drill out the passenger drag link knuckle mounting position to 7 8 of an inch as shown below b Insert the split steel tapered sleeve into the knuckle as shown below Please note for the drag link flip the spacer goes on top of the knuckle To go back to the OEM geometry simply put the spacer on the bottom as it was before 10 ROCK KRAWLER c PrePare to Install the New Rock Krawler H D Drag Link Please note in order to complete the new RK H D Drag Link Asm you will need to have purchased an Inner Tie Rod End from the OEM JK Drag Link at the pitman arm That TRE will be used at both ends of the new H D Drag Link Assembly with a quick adjuster in the middle C1 Remove the cotter pins if applicable from the ends of the OEM ball joints on the OEM drag link C2 Remove the nuts from the OEM ball joints at the knuckle and pitman arm connections on the OEM drag link C3 Using a ball joint separator or dead blow technique remove the ball joints from the knuckle and pitman arm Remove the OEM drag link for it will not be reused If you choose you can reuse the tie rod end that was at the pitman
20. s Keep the original hardware to install the new shocks 5 Remove the front sway bar links 6 Lower the front axle assembly 7 Remove the front track bar from the vehicle and save the OEM hardware for reuse 8 Remove the front springs 9 For all Non Entry Level Systems Entry Level and Stock Mod Skip This Step remove the front lower control arms and save the hardware for reuse 10 For all X Factor and X Factor Plus Kits Flex Entry Level Stock Mod and Max Travel Kits Skip This Step remove the front upper control arms and save the OEM hardware for reuse Please note the passenger side front upper control arm bolt at the frame is next to impossible to get out without cutting it off so we have provided you with anew 12mm x 90mm bolt and nylok nut so do what you have to do to get it out 11 For all X Factor and X Factor Plus Kits Flex Entry Level Stock Mod and Max Travel Kits Skip This Step install the supplied front upper control arms with the clevis bracket at the axle and the Krawler Joint at the frame using the OEM hardware For the passenger side connection at the frame use the supplied 12mm x 90mm bolt and 12mm nylok nut Set the front upper control arms to the specified length in the control arm table on page 4 or 5 for your given application Do not allow more than 2 of threads to show past the jam nut for final adjustment 12 For all Non Entry Level Systems Entry Level and Stock Mod Skip This Step All other syste
21. the tie rod end at the knuckle and secure the quick adjuster by clamping down the slits on the quick adjuster as shown below Be sure to orient the tie rod ends so the ball joints are free to move without bind Please note to follow the SAE rules of thread engagement so you do not put yourself into a bad position 12 FOCK KRAWLER Bd Quick Adjuster with Shaft Collars Installed C11 Make sure to take your JK to the local Jeep Dealer to get aligned so the steering wheel is properly centered This way you will not run into issues with ESP controls Be sure to lock the jam nuts in place with thread locker like loctite when all is said and done 13 FOCK KRAWLER Please note There is an extra hole in the front track bar bracket support bracket to allow for relocation of the OEM steering stabilizer as shown below All you need is a spacer and the hardware Steering Stabilizer Relocated 21 For all systems other than Entry Level Entry Level and Stock Mod Skip this step Remove the factory front rubber brake lines and install the new stainless steel brake lines Do not worry about bleeding the brake system at this time since you are going to have to install the new rear lines in a little while Be sure to add slack to your ABS lines and route them with your new stainless steel lines using two of the supplied zip ties to secure them together 22 Install front rims and tires and lower front of the vehicle to the
Download Pdf Manuals
Related Search