Home

ADE-II™ Theft Deterrent System Installation

image

Contents

1. The hidden reed switch is the Key both figuratively and literally to this system s success Only you will know where the reed switch is located on your Jeep as there is no outward visible sign The ADE II System uses a 30 Amp Automotive Bosch type relay that is wired to your Jeep s wiring harness a diode a hidden reed switch and a magnet The System is inserted in the wiring harness at a point that controls multiple critical circuits required for your Jeep to run The ADE II System is wired in both parallel and series to the reed switch and the Jeep s critical circuits This creates a self latching circuit that allows the Relay Coil to be maintained in the active state once the relay has been tripped by swiping the magnet over the reed switch Once activated the reed switch is no longer in the circuit ADE II Wiring Description and Diagram The ADE II System comes pre wired for you You will need to identify the Automatic Shut Down Relay Coil Wire or any other 12 volt circuit on your Jeep Cut this wire Install two 2 Crimp on connectors and plug it in You will also need to mount a ground wire to your Jeep and route and glue the hidden reed switch in place There are a total of seven 7 wires external to the ADE II System Un coil the ADE II wiring harness and follow along from the top down for the wire key Orange This is the Ground wire for the circuit It already has a connector installed on the end Att
2. When you re done IF anyone should ever stick their head all the way under the driver side kick panel area all they should see is factory look stuff Canvrioht OFFR nadOnlv INNR Paoe R af 9 t Aam On 6a How to Operate In order to start the Jeep after the ADE II System is installed you will need to follow this sequence 1 Turn ignition key to the On or Run position 2 Swipe the magnet over Hidden Reed Switch to activate the ADE II System and Jeep s critical circuits NOTE The Check Engine light should NOT light until you swipe the magnet with the Key in the Run position 3 Turn Ignition Key to Start Without swiping the magnet or Knowing where to swipe the magnet your Jeep will crank over but it isn t going to go anywhere under its own power How to By Pass The ADE II System has a by pass built into the wiring harness 1 Simply plug the Green wire into the Brown wire and your Jeep will operate as if the ADE II System was never installed This feature may come in handy if you need to leave your vehicle for service somewhere or valet parking or just have to let someone drive it and don t want to deal with the magnet Problems We have bench tested every ADE II System that we have assembled however things can go wrong in shipping We will do whatever it takes to make this right for you This is vitally important to us Once again thank you for your purchase and remember a significant porti
3. diagrams ADE II System Key Features a All electrical systems attached to the ADE II System will be automatically disabled whenever the ignition key is shut off Q These electrical systems will remain disabled until the ignition is turned on AND the hidden reed switch is activated with a magnet QO There is a stealth look with no visible indicators that the ADE II System is installed There is no value in giving a thief any clue that a disabling system is installed and must be overcome O The ADE II System is installed at a key electrical point on the Jeep to disable or open two or more critical circuits which are required to run This will make it more complex and difficult to overcome even if a thief could determine which circuits were disabled QO The ADE II System enables all circuits when a magnet is momentarily swiped over a reed switch hidden somewhere under the vast amount of plastic found in a TJ interior QO The ADE II System and all Jeep circuits are self sustaining when activated and remain so until the ignition key is turned off A simple no switch by pass is incorporated Canvrioht OFFR nadOnlv 2NANAR Paoe 1 af 9 et Resa Oh ORO Design Description The ADE II System is designed to be self disabling When you turn the Ignition Key OFF the Jeep cannot be restarted unless and until you turn the ignition On and then momentarily swipe a magnet over a hidden reed switch
4. engine should run NOTE 2005 2006 models Jeep will not crank There is a difference here for the later models as the ASD relay controls more circuits than the 2003 early 2005 models Test C By Pass Test Connect the Green and Brown wires on the ADE II wiring harness together Turn the Ignition Key to the On position Turn the Ignition Key to Start Your Jeep should crank over and the engine should run just as if the ADE II system was never installed Step 4 Locate Reed Switch Hide the reed switch inside the dashboard or some other plastic part of your Jeep Make sure you will be able to swipe the reed switch with a magnet in this location Once you have settled on a location take the plastic apart so you can glue the reed switch to the underside Using Silicon RTV or even hot glue glue the black end portion of the Reed Switch wire to the location of your choice Please be sure it remains flat against the plastic until the glue sets up Note If you are installing the ADE II System on a 2003 or 2004 TJ you will have to route the reed switch into the cab through the oval shaped rubber grommet in the firewall Step 5 Re Test Go back to Step 3 and re test the ADE II System with Test A Test B and Test C Step 6 Neatness Counts Make your installation of the ADE II System look neat Factory Look Stealth is a big part of the reason this system will make your Jeep more secure Re tape the wiring harness with electrical tape
5. harness going to Connector 103 Cut the BLUE wire going to Pin 9 in Connector 103 about five 5 inches from the connector Strip 1 4 inch of insulation from each end of the wire you just cut Install a Female Crimp on Connector to the wire end still attached to Connector 103 Plug the RED wire on the ADE II harness into this connector Install a Male Crimp on Connector to the other side of the wire which you cut Plug the WHITE wire on the ADE II harness into this connector Canvrioht OfFfRaadOn v INNR Paoe 7 af 9 et Resa Oh ORO Step 2 Mount the Ground Wire and Relay Connect the Orange wire on the ADE II wiring harness to a good ground You may want to mount the Relay via the mounting tab on the top to the same bolt There is a convenient bolt located about six inches from where you are working on the kick panel for 1997 2002 TJ s If you are installing this on a 2003 04 TJ there is a grounding bolt centered on the firewall near connector 103 Step 3 Testing the ADE II System Circuit Test A Security Test Disabled Reconnect the battery terminals Sit in the driver s seat and try to start your Jeep The engine should crank over but it shouldn t run Test B Run Test Enabled Turn the Ignition Key to the On position Take your magnet and momentarily swipe it across the reed switch You should hear the ADE II relay latch shut Turn the Ignition Key to Start Your Jeep should crank over and the
6. wrapped around the wiring harness going to Connector 106 Cut the BLUE wire to Pin 4 in Connector 106 about five 5 inches from the connector Strip 1 4 inch of insulation from each end of the wire you just cut Install a Female Crimp on Connector to the wire end still attached to Connector 106 Plug the RED wire on the ADE II harness into this connector Install a Male Crimp on Connector to the other side of the wire which you cut XK NNN NN Plug the WHITE wire on the ADE II harness into this connector Canvrioht OFFR nadOnlv INNR Paoe af 9 et Reto o a Installing on 2003 2006 TJ Please note the following information for the 2005 2006 models To install the ADE system on your 2005 or 2006 Jeep you need to locate the wire in Position 9 in connector C103 located on the firewall inside the engine compartment The color of this wire will depend on what color wire Jeep had at the time Wire Color For Jeep TJ Rubicon and Unlimited For ALL 2004 this wire will be Dark Blue as stated in the instructions For EARLY 2005 this wire will be Dark Blue just like the 2004 model year For Mid Year 2005 this wire will be PINK with a White Tracer line on it For ALL 2006 this wire will be PINK with a White Tracer line on it PLEASE NOTE These wires are found on the VEHICLE side of the connector The easy side of the connector to access is the engine side and the wires are NOT the same color NOTE Th
7. Il By Pass 4 Brown Female Light Butt Chaos Connector a Wire _ Future Red a Use Reed y G Switch Jeep Wire ik aoe Black 12 Volts f Cover You Crimp on 5 Female Connector White 4 Ps L 7 N lt lt s Jeep Wire to ASD Relay Coil You Crimp on Male Connector Installation Instructions These instructions will walk you through the six 6 steps required to install the ADE II System in a 1997 to 2006 Jeep Wrangler TJ If your TJ is different model year or your vehicle is not a TJ you will have to determine which wire controls the Automatic Shut Down Relay Coil for your vehicle Step 1 Insert the ADE II System in the Automatic Shut Down Relay Coil Wire ADE II System Insertion Point Please disconnect your Jeep s battery before continuing and please read this entire Step 1 to make sure you select the correct wire for your year TJ Take a look at this table for the information you will need based on model year e Insertio Year Connector Contactar Poeatan cin a Pont Wire Color Driver Side Kick Panel Red Light Green Driver Side Kick Panel Red Light Green Driver Side Kick Panel Solid Blue Driver Side Kick Panel Solid Blue Driver Side Kick Panel Solid Blue Driver Side Kick Panel Solid Blue Engine Compartment Rear Solid Blue Engine Compartment Rear Solid Blue Canvrioht OfFRaadOn v INNR Paoe 3 af 9 i F 1997 through 2002 Jeep TJ Connector C106 is on the Driver Side Kic
8. ach this to a good chassis ground Green and Brown ADE II By Pass These two wires are different colors by design did not want a thief to see them and think they should be plugged in If you plug the Green and Brown wires together you are bypassing the ADE II system as if it was never installed At times you might find this convenient Butt Connector There is a single wire with a Butt Connector attached This wire can be any color This wire is the ADE II to Light Chaos System interface You don t have to worry about this now It is for future use Red with MALE Connector This connector will be plugged into the 12 volt side of the wire feeding voltage to the Automatic Shut Down Relay Coil On all TJ s this will be the side of the wire attached to the connector after you cut it White with FEMALE Connector This connector will be plugged into the other side of the wire you cut during the installation This is the wire going to the Automatic Shut Down Relay Gray Cable with Black End This is the Reed Switch Cable The Reed switch is embedded in the last two inches of this cable under the black heat shrink protective covering You will route the end of this gray cable to the location you want the reed switch to live at then simply glue the black portion in place Canvrioht OFFR nadOnlv INNR Paoe 7 af 9 4 Rent On ORO ADE II Wiring Diagram Mounting Tab Orange C Ground Green Z Male t gt ADE
9. ere is an easy way to verify the harness is either early or late 2005 look at the ECM the silver aluminum box above the battery on the firewall There should be 3 harnesses plugged into that box for the Manual Jeeps and 4 harnesses for the Automatics The Manuals that have only 3 plugs will still have a 4 plug socket molded into the ECU and therefore it is the 4 plug version The 4 socket version is the Late 2005 2006 model If you are installing the ADE II System on your 2003 2006 model year TJ you will need to find Connector 103 See location drawing below It is located on the firewall inside the engine compartment Connector 103 is Black in color and has a total of 14 pins You then look for the Solid BLUE wire coming from Pin 9 Thats the one you will cut to insert the ADE II System into for the 2003 2004 TJ 2003 and 2004 Jeep TJ Connector C103 is Located in the Engine Compartment On the Firewall Here ae IR Lt me Pap ie 1 L Canvrioht OFFR nadOnlv 2NANAR Paoe 6 af 9 Rend H Connector 103 for 2003 and 2004 Jeep TJ a ast re as Notice the method of slicing on the engine side of the connector To find the color of the wire you need to cut you need to inspect the opposite side of the connector If you have not already done so disconnect both the positive and negative terminals of your KON amp KKK v battery Peel back the factory electrical tape wrapped around the wiring
10. ert the ADE Il System into for the 1997 98 TJ This wire energizes the Coil of the Automatic Shut Down Relay If you have not already done so disconnect both the positive and negative terminals of your battery v Peel back the factory electrical tape wrapped around the wiring harness going to Connector 106 Cut the RED wire with LIGHT GREEN Tracer going to Pin 10 in Connector 106 about five 5 inches from the connector S Strip 1 4 inch of insulation from each end of the wire you just cut Install a Female Crimp on Connector to the wire end still attached to Connector 106 Plug the RED wire on the ADE II harness into this connector Install a Male Crimp on Connector to the other side of the wire which you cut K KS SO SS Plug the WHITE wire on the ADE II harness into this connector Installing on 1999 2002 TJ If you are installing the ADE II System on your 1999 2002 model year TJ you will also need to find connector 106 Itis located on the driver side kick panel under the dash area See drawing above for location Connector 106 is Black and has a total of 12 pins Find the Solid Blue wire at Pin 4 That s the wire you will be cutting to insert the ADE II System into for the 1999 2002 TJ This wire energizes the Coil of the Automatic Shut Down Relay If you have not already done so disconnect both the positive and negative terminals of your battery Peel back the factory electrical tape
11. et Reto Daless2 ADE II Theft Deterrent System Installation Document Package Contents v Instructions v Two 2 Female Crimp On Connectors v Pre wired ADE II System Y Two 2 Magnets v Two 2 Male Crimp On Connectors Please Note You will only need one 1 each of the crimp on connectors We included an extra of each in the event that you mess one up in the crimping process Introduction Thank you for your purchase of the Automatic Disable Enable ADE II System ADE II will help provide a higher level of security for your Jeep or any other vehicle on which you install it Once installed the ADE II System will automatically disable multiple electrical systems that your vehicle requires to run For the Jeep TJ these systems are Ignition System Fuel Pump Fuel Injectors and the Automatic Shut Down Relay The ADE II System will also allow you to easily enable these same electrical systems with one swipe of a magnet The ADE II System can be used with any fuel injected vehicle and many non fuel injected vehicles It can also be used on other 12 volt vehicle circuits These instructions will provide details on how to install this system and where to install this on a 1997 2006 Jeep TJ If your vehicle is a different model Jeep XJ YJ ZJ etc or other fuel injected vehicle you will need to determine where to install the ADE II System based on information provided in your vehicle Factory Service Manual wiring
12. k Panel Inside the Jeep C108 BLUE C107 YELLOW C016 BLACK 1997 2002 Connector 106 Location Driver Side Kick Panel Under Das F S En 10 a 98 TJ BW wiGreen Here is a picture of connector 106 showing the red wire with green trace in position 10 which is used for the 1997 and 98 TJ We have also marked the position 4 with an arrow to show the position 4 behind the yellow wire in the photo For 1999 2002 position four will have a Solid Blue wire used to connect the ADE system You do not see the Solid Blue wire in this picture as it is not there for the 97 98 model year Canvrioht OFFR nadOnlv 2NANAR Paoe 4 af 9 et Resa Oh ORO Installing on 1997 98 TJ If you are installing the ADE II System on your 1997 98 TJ you need to find connector 106 It is located on the driver side kick panel under the dash area Connector 106 is Black and has a total of 12 pins You need to look for the RED wire with a LIGHT GREEN trace line on it coming from Pin 10 Stick your head down under the dash by the driver side kick panel By your left foot You will see three plug connectors These are connectors 106 107 and 108 Connector 106 is BLACK in color and is the only connector of the three that has twelve 12 pins Connector 107 is Yellow connector 108 is Blue and both have fourteen 14 pins Find the Red wire with Light Green Trace at Pin 10 That s the wire you will be cutting to ins
13. on of the profits from the sale of each ADE II system is donated annually to The Marine Corps Toys for Tot s Program For more information or questions during installation contact Off Road Only 651 644 2323 On the web at www offroadonly com Email inquiries will be responded to in a timely manner 4 ROST Ohn o y Canvrioht OFFR nadOnlv 2NANAR Paoe 9 af 9

Download Pdf Manuals

image

Related Search

Related Contents

Toshiba Satellite P50T-ASP5361SM  Samsung NX11 Manual de Usuario  Impulse IM200 F18 User's Manual  

Copyright © All rights reserved.
Failed to retrieve file