BeoGram 4002 repair
Contents
1. s ep This is the Control PCB after Restoration Copyright Condor Audio Israel 2009 No part of this document may be reproduced or distributed without express written permission 7 PCB 8009024 or 8009033 Repair Low supply voltage The main supply voltage rail to the circuit should be 31V I was measuring 27 2V Because all the capacitors and a couple of isolated bad resistors had been replaced already the place to look was at the semiconductors All diodes checked just fine I have very rarely found a bad diode all made by Philips in the old days in vintage B amp O equipment so I was not expecting to find any bad diodes here Although all the transistors on the Control PCB appeared to be OK while testing with power off past experience has shown this not to be the case when operating under load I concentrated on the can transistors on the left side in the above picture I replaced one pair at a time with new hFe matched pairs Modern BC550 NPN and BC560 PNP are excellent substitutes for the originals The following are the results of the change affecting the 27 2V 31V supply rail TR3 amp TR4 0 3V TR5 amp TR6 0 2V TR14 amp TR15 3 1V TR26 amp TR31 0 15V With these 8 transistors replaced the main voltage rail now measured the specified 31V 8 PCB 8009032 Modification LP prematurely ends play There is an ongoing problem with the Photo transistor and having to adjust the incandescent lamp s2. Audio Restoration Project Repair B amp O Bang and Olufsen BeoGram 4000 4002 4004 6000 Tangential Turntable Parts of this article appear with my permission on the B amp O BeoWorld website Bang and Olufsen introduced the world s first tangential tracking turntable Zero tracking error the BeoGram 4000 in 1972 It has a permanent place in the NY Museum of Modern Art The updated models produced from 1974 to 1980 were available as the BG4002 a stereo version without a built in RIAA amplifier and as the BG6000 quadraphonic version with a built in CD4 demodulator RIAA amplifier This superbly designed and over engineered BG4002 6000 version remains the most widely still available today and with proper maintenance will last 100 years if not more This article describes how to perform a complete restoration of this model including taking care of all known failures and defects The Manufacturer s Service Manual available from BeoWorld is an integral component of the proper restoration process There are slight differences in the circuits between the various types but these are covered in the individual Service Manuals available on the Beoworld org website This article covers by and large the following BeoGram type numbers Beogram 4000 5215 BeoGram 4002 5501 5503 5504 5511 5513 5514 5521 5523 5524 BeoGram 4004 5525 5526 5527 BeoGram 6000 5502 5505 5511 5515 Copyright Condor A
3. D4 calibration equipment I am pleased to be able to offer this service to my customers Copyright Condor Audio Israel 2009 No part of this document may be reproduced or distributed without express written permission This is the RIAA PCB after Modification n i a gt are OSs ba 2 od RZ 7 Copyright Condor Audio Israel 2009 No part of this document may be reproduced or distributed without express written permission 13 This shows the CD4 alignment signal on the RIAA amplifier adjusted according to the Service Manual 15 Parts for this restoration Parts and advice are available for owners who wish to tackle this project by themselves http www condoraudio com yachadm gmail com Copyright Condor Audio Israel 2009 No part of this document may be reproduced or distributed without express written permission
4. Service Manual I had feared that the voltage difference 17VDC instead of 22VDC at the switches would affect the function but further testing shows that all is OK In the picture on the white plastic hinged shields you can see the yellowish damage due to heat emitted by the standard incandescent lamps Parts required total cost less than 1 2 x Yellow LED s 1 8V Intensity gt 10 000mcd 1 x 1000 Ohm 1 Watt metal film resistor Some heat shrink tubing A CTC Current to illuminate the 33 45 Speed lights is supplied by the Red wire The voltage present on the Red wire is 22 8VDC positive which has to be reduced to about 2 Volts I chose a 1 Watt resistor 1 2 Watt would normally be enough because the resistor carries the excess voltage and heats up Using a 1 Watt resistor results in a much cooler resistor I unsoldered the Red wire from the PCB and soldered one end of the resistor in its place I soldered the other end of the resistor to the Red wire I placed the resistor at a small distance from the white plastic housing around the metal bolt to eliminate the possiblity of heat damage The LED s must be sanded lightly to give an opaque appearance to distribute the light evenly I marked the ve lead of the LED with a blue marker which you can see faintly on the upper edge of the LED If the LED s polarity is incorrect it will not illuminate In the picture the LED s upper conductor is ve and the lower is v
5. e Copyright Condor Audio Israel 2009 No part of this document may be reproduced or distributed without express written permission 11 Replacement of 4 Main Power Capacitors on Chassis I replaced the 2 main 4700uF Decoupling caps with Panasonic TSHA units the motor phase cap with a Nichicon 220uF Bipolar unit and the 3rd 4700uF Decoupling cap with a Nichicon HE unit m 60E923 W N 60E9Z9 pme zane Copyright Condor Audio Israel 2009 No part of this document may be reproduced or distributed without express written permission 12 Beogram 6000 Muddy Sound with CD 4 RIAA PCB 8005012 IMHO this CD4 demodulator is actually one of the finest RIAA amplifiers ever made So I wanted the best audio capacitors possible to extract every last nuance of sound from this board This is the RIAA PCB before Modification All SRZ jy REA EE A gt e DOME Ee NS g gt ro A a Aa Tep mep me y y E r i TOO ieni di 4 CY Pee atO g 04 052 S1 0 I replaced all the Electrolytic and Tantalum Caps with a nice blend of Panasonic FM and ECQP Elna Silmic II and Wima MKS2 caps and the potentiometers with Bourns 3352 Cermet units I advise against fiddling with the potentiometers on this PCB they are for balance and separation only and cannot improve distorted sound that is definitely a capacitor problem If the sound is seriously distorted this PCB must be calibrated with the necessary C
6. ed Leave the cartridge attached to the tone arm during this procedure Copyright Condor Audio Israel 2009 No part of this document may be reproduced or distributed without express written permission 1 Set the round Tracking weight wheel to 0 grams 2 Lift up the spring loaded arm C and keep holding it up 3 Tighten or Loosen bolt A sometimes it may have old lacquer securing it all the while tapping the tone arm gently until you feel that it is in perfect longitudinal balance 4 Release Arm C apply new lacquer on bolt A and rotate the tracking weight to that appropriate for your cartridge 5 Other mechanical adjustments need to be made reference to the Service Manual is recommended 4 PCB 8005013 Modification Replace the 1N4004 Diode with a high speed UF4007 See picture 2 above this also helped to solve the problem with the arm not lowering at the correct point when starting to play an LP I converted the Photo resistor bulb OIL2 to a White high intensity 3 0V LED and a 1K resistor see picture below This is by no means necessary but it s one less thing burnt out bulb to have to worry about in the long run 5 PCB 8009028 Modification I also replaced the 22nF Capacitor with a Panasonic Polypropylene unit See picture 2 above 6 33 45 Speed Problem PCB 8009024 or 8009033 BEOGRAM 6000 ae Pg ae J a Copyright Condor Audio Israel 2009 No part of this document may be rep
7. is at the vertical bars on the right hand side this is the End of Play signal The top one requires the stylus to keep tracking to a later closer to the centre hole position before signaling Lift and Return But if you are playing a later LP the stylus will never reach that position so will not Lift and Return The solution is to add a single wide stripe at that position as shown below The stylus will then Lift and Return correctly iai 3 En R Panne P con tare in ma Ctioatnanedt Foo Aep eierne nai naaa FT aagaaa Se SEN a S n NSS O ee DAS ia a yf The bolts securing the acrylic ruler to the aluminum mounting bar have been sealed with old style red sealing wax Copyright Condor Audio Israel 2009 No part of this document may be reproduced or distributed without express written permission 10 33 45 Speed Indicator LED upgrade The 33 and 45 indicator lamps heat up and deform their plastic housings I am a fan of LED s primarily because of their long life cool operation and highly directional intensity even though the associated resistor warms up while killing excess voltage And I also know that some purists object to the use of LED s and that s OK I respect their opinions and I have learnt a lot from them Anyway this LED upgrade works beautifully and does so without adversely affecting the required voltages on the Flip Flop circuit called a Vienna Bridge in the
8. o that the light reaches the transistor correctly Note On later production units of Type 551x this lamp has already been changed to an LED and so no modification is necessary I decided to go for overkill I replaced the 24V 25mA lamp IL1 with an opaque white medium intensity 3V LED This light from this LED is highly directional and much more intense than the original lamp So the Photo transistor on my unit a Motorola 2N5779 should be able to sense the light more precisely now The 82 Ohm resistor R4 from the Cathode to Ground must also be replaced by a 1Kohm 1W resistor Before replacing the clear acrylic ruler with the black stripes make sure that it is absolutely clean with no finger or other marks Copyright Condor Audio Israel 2009 No part of this document may be reproduced or distributed without express written permission 9 Tone arm does not Lift and Return at End of Play The very first production units appear to suffer from this fault more than later models Iam speculating that the design engineers based their lateral distance movement calculations on older LP s whose End of Play position was much closer to the centre hole Later LP s cut down on playing time and the End of Play position was much further away from the centre hole Here are 2 Rulers from the Optical sensing circuit The top one is an early production unit and the bottom one is a later production unit The critical difference
9. roduced or distributed without express written permission When pressing START lt lt The 33 indicator light on the left of the red 4ch light illuminates for a split second and then immediately the 45 indicator light illuminates and remains illuminated with platter speed 45 as indicated by the light This is while the tone arm is still moving to the left slowly over the flat aluminum plate BEFORE the tone arm even reaches the edge of the platter let alone the LP In short there was a problem in the 33 circuit which the previous owner had skillfully hidden by disconnecting the 33 indicator bulb When I connected the 33 bulb to the circuit this above problem appeared a ER o This is the Control PCB before Restoration showing the components to be replaced It was repaired by the following 1 Replacing D6 1N4148 2 Replacing C4 and C5 3 3nF with Panasonic Polypropylene units 3 Restripping and Resoldering all the coloured wires onto the PCB many were frayed and a couple were hanging on by their last strands 4 Replacing all Electrolytic and Tantalum Capacitors as follows gt 10uF with Panasonic FM units and lt 4 7uF with Wima MKS2 and Panasonic Propylene units Note that some of the Capacitors must be mounted horizontally to prevent contact with the suspension plate underneath the PCB 5 The 6 oxidized potentiometers at the right were replaced by Piher PT C10 Cermet units Faf s lt lt n
10. udio Israel 2009 No part of this document may be reproduced or distributed without express written permission 1 Replace the Rubber Drive Belts When selecting a 45 record the arm would lower at the 33 LP landing zone the first time The worn out belt was slipping and the platter didn t reach correct speed in time for the detector circuit to see it Of course on the second try it was already turning so it would lower correctly at the 45 zone there s a filter in the detection circuit and it needs the correct frequency of moving bars under the sensor There is also a second smaller belt which moves the tone arm left and right This is on the DC motor Copyright Condor Audio Israel 2009 No part of this document may be reproduced or distributed without express written permission 2 Lubrication Lubrication of ALL these points is incredibly important If the arm does not lower barring any severe electrical problem the cause is dried coagulated lubricant on the RED circled areas If you can see any dried grease remove it Then gently squirt Sewing Machine oil onto 1 Both ends of the Yellow Solenoid Piston Thick and Thin parts 2 The Piston of the Copper Damper 3 The Axle pivot connecting the Solenoid and Damper 3 Zero Balancing the Tone arm Over time the bolt A holding the tone arm s counterweight B works itself loose and the tone arm is no longer in perfect balance Sound is adversely affect
Download Pdf Manuals
Related Search