Wiring - Lee Dan Communications, Inc.
Contents
1. Improper Operation If the corridor light does not operate as described contact qualified service personnel There are no user serviceable parts on the LI118 and LI123B Corridor Lights other than bulbs BE005 BE 007 BE007 BE 007 Corridor Bells Emergency Calls Emergency calls are indicated by a steady ringing of the corridor bells Improper Operation If the corridor bell does not operate as described contact qualified service personnel There are no user serviceable parts on the BE005 and BE007 Corridor Bells 2 e IN 514 CM800 CM900 Emergency Call System Manual System Installation Read the following instructions concerning system equipment and determine installation methods before proceeding Determine equipment locations Install wiring Install housings Check wires Connect equipment Check connections e Apply power Check system operation Equipment Locations CM800 CM900 Annunciator Locate CM800 and CM900 Annunciators within easy reach of operating personnel Permitted operating temperature of 10 C 30 C must not be exceeded SFI17 SF118 SF154 Emergency Call Stations Locate emergency stations where convenient for operation Avoid areas where direct contact with water may occur The SF117 and SF118 include a 6 long pull cord permitting installation high enough to provide easy operation by the staff and by seated or prone patients The SF154 is operated by means of a push bu2. 2009 LEE DAN Communications Inc IN 514 Rev 10 9 09 Table of Contents System Operating Instructions eene 1 CM800 CM900 Annunciators eeeeeeeeeneneen nennen 1 SF117 SF118 Emergency Call Stations es 1 SF154 Emergency Call Station eere 1 TRO19 IRO19B Remote Annunciator Tone Speakers 2 LI381 Gorridor Light rdiet etre rene tnnt unten reinen 2 LI382 Corridor Light iet tm eet EP ERR ES 2 LI118B LI123B Corridor Lights een 2 BEB005 BEO07 Corridor Bells eti iere eee ete rosa 2 System Installati n 1 tian tnnt krass cena neu teinue 3 Installation Procedure sssini 3 Equipment Locations 1 erdt ttti Forte tee ie rite mute 3 Wiring Installation eese 3 Housing Installation c rrt rer rene Er eisat 4 Wire Checkout 1 ee tetti tee Here ER Sere tete epe 4 Connections CheckoUut iiiter Lesern en ee tete oe Ret rere e erede 4 Illustrations Figure 1 Master Panel Housing Chart and Wall Cut Out Details 5 Figure 2 Ring and Back Box for SF117 SF118 and SF154 Emergency Call Stations 5 Figure 3 Ring and Back Box for IRO19 amp IRO19B Tone Speakers and LI118B LI123B LI381 amp LI382 Corridor Lights 5 Figure 4 Emergency Call Hook Up Diagram with SF117 2 SF118 2 amp SF154 Emerge
3. Annunciator Tone Speakers Emergency Calls Emergency calls are indicated by a rapidly pulsating audible tone The audible tone signal can be silenced by pressing the tone off switch The IRO19 is not equipped with a tone off light The IRO19 and IRO19B tone mimics the annunciator tone either steady or pulsing Improper Operation If the speaker does not operate as described contact qualified personnel There are no user serviceable parts on the IROI9 and IRO19B Remote Annunciator Tone Speakers LI381 LI 381 Corridor Light Emergency Calls Emergency calls are indicated by steady illumination of the corridor light associated with the calling station Improper Operation If the corridor light does not operate as described contact qualified service personnel There are no user serviceable parts on the LI381 Corridor Light other than bulbs LI382 LI 382 Corridor Light Emergency Calls Emergency calls are indicated by steady illumination of the corridor light associated with the calling station The second light can be used for other call types initiated from the same zone Improper Operation If the corridor light does not operate as described contact qualified service personnel There are no user serviceable parts on the LI382 Corridor Light other than bulbs LI118B LI 118B LI123B LI 123B Corridor Lights Emergency Calls Emergency calls are indicated by steady illumination of the corridor light and a steady buzzer
4. each panel of annunciator lamps Press the lamp test button all annunciator lamps on that panel should be illuminated Improper Operation If the CM800 or CM900 Annunciator fails to operate as described contact qualified maintenance personnel If a malfunction occurs during a call in causing a lack of indication of call origin on the master station first determine the origin of the call by observing which corridor light is illuminated and then inform qualified personnel SF117 SF118 Emergency Call Stations Place an Emergency Call Pull the call cord and wait for an Attendant Note The SF118 station has a red call placed light that illuminates when the cord is pulled Reset the Station Push the slide switch up Improper Operation If the station does not operate as described contact qualified personnel There are no user serviceable parts on SF117 and SF118 Emergency Call Stations SF154 SF 154B Emergency Call Station Place an Emergency Call Press the switch in so that the red area of the switch is visible and wait for an Attendant Reset the Station Press the switch out so that the red area of the switch is not visible Improper Operation If the station does not operate as described contact qualified personnel There are no user serviceable parts on the SF154 Emergency Call Station IN 5 14 CM800 CM900 Emergency Call System Manual e 1 System Operating Instructions IRO19 IR 019 IRO19B IR 019B Remote
5. speaker station Minimum dimensions of back box must not be less than 4 x4 x1 75 LI381 LI 381 LI382 LI 382 Corridor Lights Install double gang ring or double gang ring and double gang box as shown in Figure 3 for each corridor light Minimum dimensions of back box must not be less than 4 x4 x1 5 Minimum opening on ring must not be less than 2 75 x2 75 Minimum clearance from live parts of the station to dead metal parts must not be less than 0 5 BE005 BE007 Corridor Bells Install a standard 4 Bell Box Wire Checkout Use an ohmmeter or other continuity checking device to test wires for shorts or grounds If shorts or grounds are encountered find and correct the problems before continuing Make sure the minimum number of conductors that are needed for all of the equipment being used in the system are available Connections Checkout Re check all connections to equipment If all wires and connections are satisfactory connect the primary coil of the SS 106 Transformer to a source of 117 VAC 60 Hz 30 VA max 4 e IN 514 CM800 CM900 Emergency Call System Manual Figure 1 Master Panel Housing Chart and Wall Cut Out Details Housing Wall Opening Flush Surface Width B Height OH202 OH302 8 5 16 25 OH203 OH303 12 5 16 25 OH204 OH304 16 5 16 25 OH205 OH305 20 5 16 25 E va 7 d Finished Wall In masonry walls install 0 5 x4 wood fillers attop and bot
6. FF position 9 Rectifier RUFO Model 1005 is not available from TekTone IN 5 14 CM800 CM900 Emergency Call System Manual 7 PK601A Figure 6 Emergency Call Hook Up Diagram with SF117 2 Continuous Duty Door Release LI381 Corridor Light Smoke Detector and BE007 Corridor Bell O S106 24 VAC TRANSFORMER To SEE NOTE lt 4 TO ADDITIONAL EMERGENCY q lt 4 SWITCHES Notes 117 VAC 1 Use 24 VAC connections on SS106 Q1 O Aan transformer To calculate current re C eos Kd quirements add currents of all devices BE DOR TONE E TONE on at the same time Current require SPRAKEN HAE Au ments are as follows iq GA I BUT Corridor Lamp with buzzer 16 amps E Ow X BUTTON Corridor Bell 2 amps Door release 3 amps EMERGENCY dq Annunciator lamp 04 amps bs l lin ais Wiring must be 18 gauge except DOOR RELEASE 9 GN where shown otherwise Loo gt 46 VAC BE007 connects to emergency switch on the same floor only Door release if used must be 24 VDC X 9 meen continuous duty type P4 5 Gc 5 Switch current capacity is 3 amps Seo x a Jo A T Y 6 Power supply maximum current is B ANNUNCIATOR L GE 1 amp S v 117 VAC 7 See Figure 4 for more wiring details TEST BUTTON L 1 8 Switches shown in the OFF position FACTORY t j CONNECTED NOTE PM110 4N l 9 Do not use same transformer for MODULES ONLY PK2019 and
7. Innovations in Communications CM 800 CM 900 since 1955 LEE DAN COMMUNIGATIONS ING OPERATION INSTALLATION AND SERVICE MANUAL APPLICATION FEATURES The CM800 CM900 CM 800 CM 900 Emergency Call Choice of signaling stations Signaling System is designed for elderly housing retirement facilities or wherever an Emergency Call System is required Modular master annunciators in 4 or more zones Zones custom numbers using RP 021CM lens The Emergency Call System provides audible and visual indica ki tion of all calls originating in the system Minos Choice of flush surface or desk mount annunciator The CM800 CM900 Annunciator contains lamps for call indication as well as a tone off switch and audible tone signaling devices Calls can be activated by Emergency pull station models SF 117 2B SF 117 2C SF 117 4B SF 117 4C SF 118 2B SF 118 2C SF 118 4B SF 118 4C or by push button models SF 154 SF 154B LEE DAN J LI 381 Dome Light SF 117 2B SF 117 4C Pull Stations 56 Zone CM 800 Anunciator 1 CM 800 20 1 AM 800 36 56 RP 021CM Pia PK 2019 1 OF 202T 6 Vibrating Bell Annunciator Control 800 231 1414 631 231 1414 INTERCOMS MAILBOXES DIRECTORIES 155 Adams Avenue Hauppauge NY 11788 3699 NURSE CALL ANNUNCIATORS WIRE amp CABLE Fax 631 231 1498 www LEEDAN com With continuous product improvement specifications are subject to change without notice
8. PK601A IL514 General Wiring Figure 6 RevO 123102 1 Figure 7 Connection Diagram for CONNECTION DIAGRAM FOR PARALLEL CM800 PANELS Parallel CM800 Panels Panel 2 PK2019 Notes q Use 16 VAC connections on SS106 E x N E Transformer P G R1 common Speaker sexe ORI Tone o O R2 Normally o 4 O R2 en S be Wiring may be 22 except where S R3 Nornaly R3 82 shown otherwise pa Closed V Bd PK2019 Annunciator Control Unit may OA pel aa Tone be mounted outside of annunciator Ow l o Buton Tone Off enclosure Lamp Q Ta e8 S106 l Transformer 16 VAC TO STATIONS v 117 VAC Annunciator Lamps Panel 1 Annunciator Lamps Panel 2 1L514 General Wiring Figure 7 RevO 123102 1 8 IN 514 CM800 CM900 Emergency Call System Manual
9. al Figure 5 Emergency Call Hook Up Diagram with SF117 4 Continuous Duty Door Release LI381 Corridor Light LI123B Corridor Light with Buzzer and BE005 Corridor Bell y a RECTIFIER RECTIFIER E See NOTE 9 See NOTE 9 p 4 TONE SPEAKER lt e e 24 VAC TRANSEORMER RENO TO ADDITIONAL EMERGENCY lt SWITCHES lt N PK2019 O RI R2 R3 Osa TONE ES OFF Oa BUTTON 117 VAC x 1238 Ow w BUZZER 2 e eo Y zu T Os m Op Oo S DOOR RELEASE VD One O t O T2 e o e DOOR RELEASE ce SF117 4 EMERGENCY SWITCH ANNUNCIATOR LAMPS 117 VAC TEST BUTTON FACTORY CONNECTED t t NOTE PM110 4N MODULES ONLY IL514 General Wiring Figure 5 RevO 123102 1 Notes 1 Use 24 VAC connections on SS106 transformer To calculate cur rent requirements add currents of all devices on at the same time Current requirements are as follows Corridor Lamp with buzzer 16 amps Corridor Bell 2 amps Door release 3 amps Annunciator lamp 04 amps 2 Wiring must be 18 gauge except where shown otherwise 3 BE005 connects to emergency switch on the same floor only 4 Door release if used must be 24 VDC continuous duty type 5 Switch current capacity is 3 amps 6 Power supply maximum current is 1 amp 7 See Figure 4for additional wiring details 8 Switches shown in the O
10. lation PK2019 PK 2019 Options e For 30 second delay before tone connect terminal A to terminal N e Forsteady tone connect terminal W to terminal N If the annunciator lamp is flashing the tone will be intermittent despite terminal W connection Housing Installation CM800 CM900 Annunciators Flush Wall Mount Provide a wall cutout as shown in Figure 1 Fit the back box and frame assembly into the prepared opening Fasten the assembly in place Note The back box must be TekTone OH200 Series Surface Wall Mount Fasten the back box and frame assembly to the wall through the holes provided in back of the box using suitable fasteners Note Back box must be TekTone OH300 Series SFI17 SF118 SF154 Emergency Call Stations Install single gang ring or single gang ring and double gang box as shown in Figure 2 for each emergency call station in system Minimum dimensions of back box must not be less than 4 x4 x1 5 Minimum opening on ring must not be less than 1 75 x2 75 Minimum clearance from live parts of the station to dead metal parts must not be less than 0 5 IR019 IR019B Remote Annunciator Tone Speakers Install double gang ring or double gang ring and double gang box as shown in Figure 3 for each tone speaker station Minimum dimensions of back box must not be less than 4 x4 x1 5 LI118B LI123B Corridor Lights Install double gang ring or double gang ring and double gang box as shown in Figure 3 for each tone
11. ncy Switches and LI381 amp LI118B Corridor Lights 6 Figure 5 Emergency Call Hook Up Diagram with SF117 4 Continuous Duty Door Release LI381 Corridor Light LI123B Corridor Light with Buzzer and BE005 Corridor Bell 7 Figure 6 Emergency Call Hook Up Diagram with SF117 2 Continuous Duty Door Release LI381 Corridor Light Smoke Detector and BE007 Corridor Bell sess 8 Figure 7 Connection Diagram for Parallel CM800 Panels 8 IN 514 CM800 CM900 Emergency Call System Manual iii System Operating Instructions System operators must read the following operating instructions concerning system equipment and terms used in conjunction with the equipment CM800 CM 800 CM900 CM 900 Annunciators Answer Emergency Calls Emergency calls are indicated by simultaneous operation of the following signals Steady illumination of the associated station selector lamp which is marked to indicate call origin e Rapidly pulsating audible tone The audible call signal may be canceled by pressing the tone off button The tone off light will illuminate to indicate that tone is silenced The tone off button may be pressed at any time to verify operation ofthe tone off lamp Call signals may only be canceled at the point of origin and all calls must be answered in person Test Station Annunciator Lamp if so equipped One lamp test button is provided on
12. tom of opening for housing attachment Finished Floor Figure 2 Ring and Back Box for Figure 3 Ring and Back Box for SF117 SF118 and SF154 IRO19 amp IRO19B Tone Speakers and Emergency Call Stations LI118B LI123B LI381 amp LI382 Corridor Lights 1L514 2g ring 2g box RevO 123102 1 Install ring with panel mounting holes at top and bottom as shown Install ring with panel mounting holes at top and bottom as shown IN 514 CM800 CM900 Emergency Call System Manual 5 iAjuo sanpo Nr OLUG 310N L 204280 0 eH v en614 Bui e1eues Y FTI p Q3193NNO2 AYOLOVS f 8L 3 G aloy ees jeuondo 8 NOWWOS sanya 3 WOLVIONDNNY OVA ZEL G 9 ON ees jeuondo VcL9 d 1 8 0N ees YINWHOJSNYHL ovA 91 OV uuo IMS Hot z LaS NOWWOO N AB 3NOL pepeeu s uouiuJoo Use JI pej ersu Sa NadO pee aq 0 juo speeu pue en si Bum inicie d ISF uong Uonisod 440 eui ui UMOUS ale seuoiiMg O 9u0 ejnsojoue Joyelounuue cen Jo episino pejunou eq Aew pun jo3002 Jojerounuuy 6L02Md ed SIMJOYJO UMOYS 8JeuM 1deoxe zzi eq AewW DuulM JOUJJOJSUEJ 90LSS UO suonoeuuoo OWA 91 esf S9 ON wyo SP Jayeeds geroul 610 Md 6 LOY Guim y due jo euo140J Bunim pueBausiq 6LOZMd pue g6Lodul GLOUI 40 Wesbeiq Buln S 4 17 JOp10D GSLLIT 8 LSEI7 pue seyoums ouosDujeur3 p6LHJS 8 Z SLLAS Z ZL LAS UNM wepe dN Y00H je Aouebsewy p e1nDi4 6 IN 514 CM800 CM900 Emergency Call System Manu
13. tton located on the station IR019 IR019B Remote Annunciator Tone Speakers Locate annunciator tone speakers as needed and where convenient for operation Location must provide for unobstructed visibility of the tone off indicator IRO19B LI381 LI382 LI118B LII23B Corridor Lights Locate corridor lights in the corridor above or beside the door of the associated rooms Location must provide unobstructed visibility of the corridor light in both directions PK2019 PK 2019 Control Unit The PK2019 may be surface mounted adjacent to the 8106 if necessary If remotely located cable run from PK2019 to CM800 CM900 must not exceed 100 PK601A PK 601A Power Supply Surface mount the PK601A adjacent to the SS106 and PK2019 PK612A PK 612A DC Flasher Surface mount the PK612A adjacent to the SS106 and PK2019 BE005 BE007 BE 005 BE 007 Corridor Bells Locate BE005 and BE007 Corridor Bells in corridor above door height Location in corridor will be determined by the number of bells required on each floor SS106 AKA PS 30A Transformer Locate SS106 in an accessible area near a source of 117 VAC Observe local codes Wiring Installation Run wiring conduit from corridor light to corridor light and terminate at the CM800 or CM900 annunciator panel Select conduit size according to the application as shown in wiring diagrams in this booklet Observe local codes IN 5 14 CM800 CM900 Emergency Call System Manual 3 System Instal
Download Pdf Manuals
Related Search