installation manual rear parking sensor system
Contents
1. correctly Splice the thick white wire Replace the fuse with a new one Replace ECU with a new one Connect the plug of each sensor properly Replace any damaged sensor with a new one Connect the plug of each sensor properly and replace any damaged sensors with a new one Connect the plug of each sensor properly and replace any damaged sensors with a new one Connect the plug of the harness to the ECU Replace any damaged sensor with a new one The warning does not go off when objects are outside the detection area Replace ECU with a new one The gear is in R and the warning goes off for a while although there is no object behind the vehicle The gear is in R and the warning goes off intermittently although there is no object behind the vehicle The sensor surface is covered with foreign materials such as mud water drops etc One of the sensors is damaged The sensors are not installed in the proper position The sensors have detected harsh roads The vehicles posture is weighted heavily to one side Confirm whether the sensor surface is covered with foreign materials Confirm whether each sensor functions properly Confirm whether the sensors are installed in the proper position Confirm the road condition Confirm the vehicles posture Clean up the sensor surface and see if it functions normally Replace an2. the figure 27 Tape the harness to the trim as shown in the picture The amount of harness left loose from the last piece of tape is 140mm Dn 140mm FS as u y E a A E E P 2 cad 28 1 Connect the 2 pin connectors of the buzzer and of the main harnesses together 28 2 Restore the upper trim panel d y N 28 3 Restore the lower 77 Y quarter trim panel 7 Reminder 1 After installing the sensor system please confirm that the system functions properly 2 Please make sure to check if the original electronic devices of the vehicle work properly before re assembling the removed parts 3 Restore Cargo side trim LH Rear scuff plate LH rear seat cushion rear trim luggage tray rear combination lamps and fasten all bolts and fasteners of rear bumper 4 Reconnect the cable to the battery Product specification Rated Voltage DC 12 0V Operation Voltage DC 9 6V 16V Operation Temp 30 C 80 C Storage Temp 40 C 85 C Sensor specification Rated Voltage DC 8V Operation Voltage DC 7V 9V Sensor Sensibility 100cm 600 480 ACRYLIC PLATE shifted to R the alert does not beep When the gear is shifted to R the alert beeps twice not once When the gear is shifted to R the alert beeps three times When the gear is shifted to R the alert beeps four times The gear is in R but the warning does not go off although th
3. MITSUBISHI MOTORS GENUINE PARTS INSTALLATION MANUAL REAR PARKING SENSOR SYSTEM Thank you for your purchase of MITSUBISHI genuine PARKING SENSOR SYSTEM This manual explains the procedure for fitting PARKING SENSOR SYSTEM Read this manual before installation to ensure correct installation PART NUMBER APPLICABLE MODEL MZ380467EX i MiEV COMPONENT PARTS ECU 1PCS 2 SENSOR 2PCS 3 WIRE HARNESS 1PCS 4 BUZZER 1PCS 5 C CLIP 2PCS 6 SPONGE 10PCS 7 CABLE TIE 10PCS 8 Sensor Fix Paper 2PCS Tools necessary for installation SCREWDRIVE WRENCH 10mm DIAGONAL CUTTERS CENTER PUNCH ORNAMENT REMOVER Zl PA qe o ME 2 e x n OE MASKING TAPE DROP CLOTH SAFETY GLASSES DRILL BIT 3mm 15mm lt LI y SIISIIIIISI I A 6 WH HOLE SAW 26mm WATER PROOF SEALANT ALCOHOL MITSUBISHI MOTORS 8 9 Precautions This system is designed to assist the driver with parking the vehicle The system operates by detecting ultrasonic waves that are reflected by obstacles behind the vehicle This system is an aid for backing up only and is not a substitute for your visual confirmation Due to the time requirement of the ultrasonic waves to be sent out and reflected while moving backwards please use speeds under 10km h to move backward While using this system to move backward please turn down the volume of the radio so as not to drown out the sound of the warn
4. ere are objects behind the vehicle Function Inspection Troubleshooting Possible Cause Confirmation Method When the gear is The buzzer plug has not been inserted Tail light power wire has not been spliced correctly The fuse to the ECU may have blown ECU is damaged One or more of the sensors is not connected properly One of the sensors may be damaged Two of the sensors are not connected properly or may be damaged Three or more of the sensors are not connected properly or may be damaged The sensor s harness has not been connected to the ECU One of the sensors is damaged The objects are outside the range of detection ECU is damaged Confirm whether the buzzer plug is inserted Check if reverse lights are on or that the thick white wire has been spliced Check whether the fuse has been blown Confirm whether the ECU is damaged Confirm whether the sensors are properly connected Confirm whether each sensor functions properly Confirm whether the sensors are properly connected and whether each sensor functions properly Confirm whether the sensors are properly connected and whether each sensor functions properly Confirm whether the harness has been connected properly Confirm whether each sensor functions properly Refer to the service manual for the range of detection Confirm whether the ECU is damaged Solution Insert the buzzer plug
5. ing Prevent brute force or high pressure washes from directly impacting the sensor It is easy to damage the sensor device Snow mud water droplets foreign matter etc covering the sensor device may cause the device to falsely detect The device should be kept clean at all times The following obstacles are known to cause difficulty in detection please note X Sharply angled barriers X Cotton snow etc are apt to absorb the object of the sound wave The following situations may lead to a false detection by the sensor please note X While moving backward in a road full of bumps and holes Reversing on a gravel road grass road or up a road with a slope X When the height of the automobile s rear shortens because of a heavy load X When ultrasonic waves from another vehicle are present nearby x There is an environmental noise 40K HZ This system is only suitable for a vehicle using 12V The product is composed of two center back sensors Please pay attention when reversing the car 10 After installing please hand over the manual to the customer Main Checkpoints X Before Installation Start and stop the engine and check if the power system functions properly such as door locks and the power ignition system Open the rear tail gate When installing or removing parts Loosen or tighten bolts Use a Phillips screw and nuts using tools driver that fits the that match their sizes recess in the head
6. lips and fasteners from the rear end trim in the picture 12 Dismantle the lower left quarter trim panel CAUTION Use a drop cloth to cover the top edge of the quarter trim panel before removing 14 Route the harness as shown below positions of ECU Buzzer GND Back Light Splice Buzzer i ADA 15 Install the ECU in the location as shown using the adhesive tape on the back of the ECU sv eri E gt n loz b Eu 16 Splice the white wire of the Back Up Light system for power 17 Wrap the splice connector with sponge tape 18 Connect the harness to the ground location as shown in the picture 19 Zip tie the harness in the locations as shown 8 locations 20 For vehicles without rear end harnesses make a small cross slit on the plug with a knife to allow the Sensor harnesses B to fit through it Route Sensor harnesses B through the plug and along the rear of the vehicle 22 Route the harness as shown below and tape the harness at the circled locations 7 location 23 Restore the inside bumper Styrofoam 24 1 Connect the sensors in the rear bumper to the harness 24 2 Restore the rear bumper 25 Make a 615 mm hole at the location specified in the picture on the left lower rear quarter panel that was perviously removed 26 Route the buzzer harness through the 615mm hole and attach the buzzer to the trim as shown in
7. nstallation instructions 1 Put the left Sensor template on bumper as shown in the picture Mark the pilot hole locations with a punch the left template can be flipped over for the right side Remove the rear bumper fasteners 9 locations 3 Remove fasteners 3 locations inside both of the rear fenders The picture shows the left side only 4 After removing the fender fasteners on both the right and left side the rear bumper can be removed CAUTION 1 Disconnect the light harness before fully removing the bumper 2 Add masking tape to the edge of fender to protect the paint when removing the bumper 5 Remove the inside bumper styrofoam mu o cmo sh a E Sd 1 gt EEE EEE EEE EEE EB EB RR GE EB UE A h 6 On the removed bumper drill a 3mm pilot hole at the locations previously marked with the punch 7 Use a 26mm hole saw to drill out the sensor locations on the bumper Take care to center the hole saw to the pilot hole closest towards the bottom of the bumper 8 1 Position the sensor into the hole 8 2 Adjust the sensor so that the notch on the sensor alligns with the notch in the drilled out hole 8 3 Install the hook for the back side of the sensor and check for secure fitment 9 Remove the rear seat by lifting it in the direction of the arrows in the picture No tool required 10 Dismantle the left rear Side scuff plate 11 Remove the c
8. of the screw being loos ened or tightened Before installation Be sure to disconnect the negative terminal cable from the battery To remove plastic parts use a trim remover Donotletharnesses be pinched between parts Do not pull on wiring harnesses strongly When connecting con nectors push them against each other until the lock clicks When disconnecting connectors first unlock them then separate the connectors by pulling on themselves not on cables Jc Route the harness away from hot compo nents such as the engine and radiator f GP Ia ickTR Protect the harness from sharp edges by covering the edges with tape or other suitable materials Do not fasten the har ness to brake pipes or high pressure air condi tioner pipes Apply sealant to grom mets at portions where the harness run through Clamping harness Fasten the additional Bind up extra length of harness to an existing the harness using a tie vehicle harness using wrap tape or tie wraps Check the installed product for function Also check lamps horn wipers etc for proper operation Check the product and wiring for installed con dition before connect ing the cable to the If one tie wrap is too short use two con nected together Disassembly and i
9. y damaged sensor with a new one Reinstall the sensors in the proper position Misdetection is possible when the system detects harsh roads or small objects on the road Misdetection may occur if the vehicle is heavily weighted in the rear or at the cusp of a steep incline Refer to service manual for figure oOKMCOO6 522XA000X us FUP LH ESTEE Ol Oc Ue Or OS 0
Download Pdf Manuals
Related Search