Water Blast Service Manual
Contents
1. LOCATION 8 Close the doors to be sure they line up evenly and close securely If either of the doors is lower than the other raise the mounting foot on the side of the game with the lower door until the doors close evenly WATER BLAST ARCADE MANUAL EVENGAP 9 With the doors open slide the seat base under the game until the holes in the base line up with the holes in the bottom of the cabinet SEAT BASE BOLTS NOTE JUST SCREW THE BOLTS INTO THE SEAT BASE ENOUGH TO HOLD IN PLACE DO NOT TIGHTEN DOWN OR THE SEAT BASE WILL LIFT UP THIS FREE FLOATING DESIGN ALLOWS THE SEAT BASE TO LEVEL TO THE FLOOR INDEPENDENTLY OF THE GAME 10 Plug the game into a suitable A C Receptacle 11 Turn the game on to be sure it powers up properly 12 Remove the protective wrapping on the tank screen and set the screen into the tank 13 Get a bucket with 5 gallons of water in it to fill the game reservoir NOTE THE GAME COMES WITH AN ALCOHOL WATER MIXTURE TO PREVENT FREEZE DAMAGE WHEN SHIPPING IN COLD CLIMATES THIS FLUID SHOULD BE WASHED OUT WHEN THE GAME IS SET UP To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS 14 Fill the game tank with 5 gallons of water NOTE ANY WATER CAN BE USED HOWEVER USING DISTILLED WATER WILL KEEP YOUR GAME MUCH CLEANER AND SPOT FREE AND EXTEND YOUR WATER CHANGE INTERVALS 15 Set th2. Power Power Sound Problems No sound Low Sound Intermittent Sound Low Volume Faulty speaker harnessing Faulty speaker Faulty sound board or sound board harnessing Faulty Main P C Board Check Volume Control and adjust as necessary Check connections and or repair harnessing Check and or replace speaker Check connections or Replace Sound Board Check and or repair or replace Main P C Board Game does not take or add money correctly Coin switch out of adjustment Coin mech dirty or improperly adjusted Faulty Coin switch Faulty coin switch harness or connector Improperly programmed electronic mech Game improperly programmed Faulty Front Panel Board Faulty Main P C Board or component Re bend coin switch wire Clean and adjust mech as necessary Check and or replace switch Check and or repair harnessing Reprogram or replace electronic mech Check programming options and adjust Repair and or replace Front Panel Board Repair and or replace Main P C board Ticket Dispenser not working properly or no tickets being dispensed No tickets in the game Tickets jammed in dispenser Ticket dispenser sensor blocked with debris Poor connection on the ticket dispenser Game improperly programmed Faulty ticket dispenser Faulty ticket dispenser harnessing Repair and or replace Front Panel Board Faulty Main P C Board Refill ticket dispenser and press the reset button Clear ticket jam Clean off sensor
3. Check and or replace connectors Check ticket programming options Replace dispenser Check and or repair harnessing Faulty Front Panel Board Replace or repair Main P C Board Game will not start or pump will not run Game power off Main fuse blown Ground wire broken or loose Faulty coin switch GFI circuit tripped Faulty pump Power Supply problem or failure Faulty P C board or component Check on off switch and power cord Check and or replace fuse as necessary Replace or tighten faulty ground wire Check coin switch Start game and push GFI reset button Check and replace pump Check Power Supply output and connections Repair and or replace main P C board Game stops or is stopped with nothing displayed The power connector is disconnected Possible faulty connection or short circuit Reconnect the connector securely Check all circuitry for faulty connections or short circuits Water stream crooked or weak Clogged gun nozzle Partially clogged filter Kinked hose Low water level or no water Check and clean gun nozzle Check filter and clean if necessary Check all hoses Check water level and fill if necessary Display lights won t move Faulty target switch Faulty or disconnected harness Faulty Main P C board Check target switch Check and repair harnessing Repair or replace main P C board Water not coming out of gun Clogged gun nozzle Kinked hose Low water leve
4. Display P C Board Servicing 4 PARTS LISTINGS 5 SCHEMATICS 6 WARRANTY To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL 1 INTRODUCTION 1 1 Overview and Technical Features Thank you for purchasing the new WATER BLAST from Bob s Space Racers Built on a long tradition of value the WATER BLAST retains all of the great game play you have come to expect from a game from BSR It has been designed and engineered by taking years of experience in producing industry leading Water games and combining this experience with modern manufacturing technology developed for this application All of this is brought together to provide the operator and customer with the best possible experience FEATURES FOLDING DESIGN The new cabinet folds up for easy WATER TANK The new water tank is made from and fast assembly The game can be assembled and vacuum formed molded plastic with smoothly ready to play in as little as 15 minutes rounded corners This tank will look great for years to come and is very easy to clean WATER WATER SHIELD The new water shield has a tempered glass top and scratch resistant acrylic sides for years of service This design can be washed over and over and still retain its like new appearance UP FRONT ACCESS All servicing of the game can be done through the front doors This eliminates having to move the game
5. or EMAIL QUESTIONS TO Tech BobsSpaceRacers com or VISIT THE CUSTOMER SUPPORT SECTION ON OUR WEBSITE WWW BOBSSPACERACERS COM 28 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL WATER BLAST Fill Level Update 6 13 07 NOTE THIS UPDATE WILL ALLOW FOR THE PROPER FILLING LIMIT OF THE WATER BLAST GAME S WATER TANK Correct fill distance e INSTALL DECAL AS SEEN IN THE ABOVE IMAGE 6 FROM THE BOTTOM OF TANK 29 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL WATER BLAST Ventilation Update 6 13 07 NOTE THIS UPDATE WILL ALLOW FOR BETTER VENTILATION OF YOUR WATER BLAST GAME IMAGE 1 30 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL e If You Find That The Rear Metal Access Plate Is Bolted Directly To The Game As Shown In Image 1 And Image 2 Unbolt It And Insert Spacers Washers Or Nuts To Separate The Door Plate From The Game Be Sure To Evenly Space Each Bolt When Attaching the Rear Access Plate to the Game So As To Not Bend It Recommended Spacing Is 4 1 2 When Finished The Game Should Look Like Image 3 And Image 4 31 To Purchase This Item Visit BMI Gaming
6. www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL Water Change amp Filter Cleaning Service 6 27 07 NOTE THIS UPDATE EXPLAINS HOW TO CHANGE THE WATER OF YOUR WATER BLAST GAME Water And Filter Should Be Cleaned Twice A Month Or Every Two Weeks 1 Turn off and unplug power to avoid risk of shock 2 Open the front Coin Ticket doors 3 Remove the Coin Drawer Image 1 IMAGE 1 4 Locate and remove the Allen bolt from the bottom of the Coin Box Image 2 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL 5 Slide the Coin Box out of the game Place it on the left side Image 3 IMAGE 3 6 Slide the Pump Assembly forward Be careful not to kink any hoses or pull any wires Image 4 33 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL 7 Turn the GAME DRAIN Valve to the DRAIN position Image 5 8 Hold the drain hose in a bucket Using the PROGRAMMING Panel Press PROGRAM Press SELECT until DRAIN is displayed Press STEP The pump will turn on and start to fill the bucket 9 Press STEP again to turn pump off DO NOT RUN THE PUMP DRY 10 Once the tank is empty turn the DRAIN GAME valve to GAME Image 6 11 Press the PROGRAM button 12 Unplug the p
7. and remove the single bolt located in the bottom P C BOARDS of the cash box enclosure See image to the right L 4 Slide the cash box enclosure out of the game and unplug the programming panel connector Set the cash box enclosure to the side 5 Unplug the Appropriate harness from the Main P C Board If it is the left hand display unplug connector P6 from the Main board If it is the Right hand display unplug P7 NOTE WHEN DISCONNECTING THE RIGHT HAND DISPLAY CONNECTOR P7 BE SURE TO UNPLUG THE SINGLE WIRE FAST ON CONNECTOR THAT IS RIGHT AT THE CONNECTOR AS WELL 6 Remove the upper and lower rear access panels to be able to access the display harnessing See image to the right NOTE THE DISPLAY HOUSING AND HARNESSING ARE REMOVED AND INSTALLED AS A SUB ASSEMBLY 7 Pull the display harness to the rear of the game and up through the cabinet holes 8 Unbolt the display housing from the rear of the cabinet and pull straight out of the game 9 Assemble in reverse order 3 3 11 Display P C Board Servicing 1 Slide the display filter out of the housing DISPLAY 2 Remove the 8 bolts that hold the Display mounting bracket to the Display housing FILTER See image to the right 3 Slide the mounting bracket out of the housing 4 Remove the connectors and defective display P C Board 5 Assemble in reverse order 21 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255
8. away from the wall for access to the pump and electronic components For example removing 1 bolt from the cash box enclosure makes it possible to slide the pump unit right out through the front door WATER PUMP ASSEMBLY The water pump assembly uses an all plastic impeller and housing to completely eliminate any rusting or corrosion in the water system This greatly extends the time between water changes The pump assembly also uses a basket type washable water filter in a clear view housing to keep the game working properly The entire pump assembly can be easily removed from the game making bench top servicing possible Picture on next page To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL NEW LIGHTING The game uses florescent lighting throughout greatly extending the time between bulb changes to years rather than months MARQUEE BULB TARGET BULB HIDDEN SCORE DISPLAYS The solid state score displays are replaceable as a sub assembly making service easier NEW SCORE SENSORS The game utilizes fully encapsulated magnetic switches for the score sensing greatly extending the reliability of the game SCORE __ SCORE SENSOR DISPLAYS SIMPLE ELECTRONICS The new design uses only 1 electronic board making troubleshooting far easier than ever ELECTRONICS BOARD To Purchase This Item Visit BMI Gami
9. game operator for the purpose of customizing the game to suit their location The operator will press the PROGRAMMING button once to enter the programming mode The operator will press the SELECT button to scroll through the various options that are on the left hand display The operator will press the STEP button to scroll through the various settings for each option that are shown on the right hand display The operator will press the PROGRAMMING button once again to EXIT the programming mode and save all of the new values to the games memory Below is detailed information for the operation of each of the programming options DRAIN PROGRAMMING PANEL 2 2 VOLUME This option controls the sound volume from the speaker on the front door of the game The range for this option is 1 10 10 being the loudest The default value for this option is 3 2 3 COINS PER CREDIT COIN CR This option determines how many coins are needed to earn a credit Each credit will automatically start a game The range for this option is 1 10 the default value for this option is 1 NOTE There is no free play option for this game If free play is desired set the game to 1 coin per credit and install a momentary contact push button to start the game 2 4 ATTRACT MODE ATTRACT This option determines how often the attract sounds or player taunting will be heard from the game The range for this option is 0 5 minutes Setting a
10. 0 shuts the attract mode off The default value for this option is 5 10 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL 2 5 JUST FOR PLAYING TICKETS This option determines how many tickets the player gets just for playing the game The range for this option is 0 10 The default value for this option is 3 2 6 WINNER TICKETS This option determines how many tickets the player gets for winning the game The range for this option is 0 10 The default value for this option is 5 2 7 GAME TIME TO WIN This option determines how many seconds it takes to win the game when the target is kept depressed The range for this option is 5 20 seconds The default value for this option is 12 2 8 TIME OUT This option determines how many seconds of inactivity target not depressed are necessary for the game to automatically end The range for this option is 0 10 or 20 seconds Setting a 0 disables the auto end function The default value for this option is 10 NOTE If the game auto ends the JUST FOR PLAYING tickets ONLY will be dispensed and there are no winners 2 9 DRAIN WATER This option is used as a convenient way to run the pump when setting up changing water or draining the game Pressing the VALUE button will turn the pump on or off 2 10 MONEY This option determines whether the board is set up for Coin Play or f
11. 1 561 391 7200 BOB S SPACE RACERS 4 PARTS LISTING WATER BLAST ARCADE MANUAL ARWB1003 ARWB1017 ARWB1018 ARWB1019 ARWB1020 ARWB1021 ARWB1022 ARWB1025 ARWB1026 ARWB1027 BKT ARWB1029 BRACKET ARWB3001 ARWB3011 ARWB3016 ARWB3017 ARWB3020 ACRYLIC ARWB3021 ARWB6002 ARWB6017 ARWB9004 ARWB9013 CX800085 M0006905 M0800035 M0800204 MX006103 MX006330 MX007203 ARWB7001 ARWB7010 ARWB7011 ARWB7012 ARWB7013 ARWB7014 DECAL ARWB7015 ARWB7016 DECAL ARWB7017 ARWB7018 MECHANICAL PARTS TANK WATER STRAINER GUN BODY GUN HANDLE MOUNT WATER GUN HANDLE GUN MOUNTING PLATE GUN BOOT BEZEL STAINLESS CASH BOX HASP TARGET MOUNTING BRACKET OUTER LEFT SIDE GLASS MTG BKT OUTER RIGHT SIDE GLASS MTG INSIDE GLASS MOUNTING WATER GUN SWIVEL BLOCK BENCH SEAT TOP TARGET PIVOT SWING TARGET DISK SIDE WINDOW GLASS SAR TOP GLASS TEMPERED PRESSURE GAUGE BULKHEAD WATER PAN DRAIN FULL PUMP ASSEMBLY FLASHER BULB PANEL COMPLETE DISPLAY FILTER SMOKED GREY GUN CENTERING SPRING CASH BOX DELTRONICS 1275 TKT DISPENSER GUN BARREL TIP GUN BARREL PAINTED TARGET PAN ASSEMBLY GRAPHICS DECALS SERVICE MANUAL CABINET RIGHT SIDE DECAL SET CABINET LEFT SIDE DECAL SET CONTROL PANEL DECAL MARQUEE DECAL TICKET DISPENSER PLAYER 1 DISPLAY MIRROR DECAL TICKET DISPENSER PLAYER 2 LEVER DECAL DRAIN LEVER DECAL GAME ELECTRONIC ELECTRICAL PARTS ARWB2001 MAIN P C BOARD ARWB2002 MAGNET
12. ATER CONDITION REMEMBER TO REMOVE THE FILTER CANISTER AND CLEAN SCREEN EACH TIME WATER IS CHANGED FOR INSTUCTIONS ON HOW TO EMPTY OR DRAIN THE WATER SEE THE CHANGING THE WATER SECTION 3 CHECK PLUMBING SYSTEM FOR LEAKS OR PLUMBING ISSUES Miscellaneous Maintenance 1 CLEAN GUN TIPS OF ANY DEBRIS NOTE IF THE WATER GUNS ARE NOT SHOOTING STRONG OR STRAIGHT CLEAN THE GUN TIP FOR INSTUCTIONS ON HOW TO CLEAN THE GUN PARTS SEE THE CLEAN GUN PARTS SECTION GUN TIP REMOVE TIP AND CLEAN WHEN ONE DOES NOT SHOOT WATER 14 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL 3 3 Detailed Troubleshooting and Repair er 3 3 1 Changing the Water 1 Set the game s GAME DRAIN valve to the drain position 2 Press the PROGRAM button on the game s programming panel to access the programming options 3 Press the SELECT button and advance to the DRAIN option 4 Press the VALUE button to turn the pump on and off NOTE THE PUMP IS RUN ON A GROUND FAULT INTERRUPTER PROGRAMMING CIRCUIT THIS IS TO PROVIDE A HIGH DEGREE OF SAFETY TO PANEL THE CUSTOMER IF THE PUMP DOESN T RUN WHEN THE GAME IS STARTED CHECK THE RESET BUTTON ON THE GROUND FAULT OUTLET ON THE RESET BUTTON MUST BE DEPRESSED DURING GAME PLAY TO BE ACTIVATED PUSHING THE RESET BUTTON WHEN THE GAME IS OVER WILL NOT HAVE ANY
13. EFFECT 5 Hold the drain hose into the 5 gallon pail and press the VALUE button to start the pump 6 Run the pump until ALL of the water empties out of the tank Turn off the pump 7 Turn the GAME DRAIN valve to the GAME position 8 Remove the screen at the bottom of the tank and clean both the tank and the screen Re install the screen 9 Add 5 gallons of water to a bucket and add 1 TBSP Cascade Dishwashing powder This will help keep the glass clean DO NOT use too much Cascade or foaming will result SUGGESTION ALTHOUGH ANY WATER CAN BE USED USE DISTILLED WATER WHENEVER POSSIBLE DISTILLED WATER HAS ALL OF THE MINERALS REMOVED AND WILL DRASTICALLY EXTEND THE TIME INTERVAL BETWEEN WATER CHANGES 10 Clean the inside of the glass with a plastic scrub pad to remove dirt and sediment from the glass NOTE IF THE GLASS IS BADLY STAINED USE C L R MINERAL REMOVAL SPRAY FIRST TO GET RID OF TOUGH MINERAL DEPOSITS 11 Spray RAIN X on the inside of the glass to help prevent minerals from forming on the glass 12 Fill the tank with the 5 gallons of water 13 Set the game s GAME DRAIN valve to the DRAIN position 14 Press the PROGRAM button on the game s programming panel to access the programming options 15 Press the SELECT button and advance to the DRAIN option 16 Press the VALUE button to turn the pump on and off 17 Hold the drain hose into the 5 gallon pail and press the VALUE button to start the pump 18 Run th
14. I Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL Board Schematic 2 5 INTE 25 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS LED Display Schematic 0000000 il i 0000000 EH A 7 Il 0000000 eoooose E rake ees 22 4 771 174 3 4 21 00000068 00002000 0000000 oo00000 amp Ww ooooooo E 26 WATER BLAST ARCADE MANUAL pp ka bb To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL 6 WARRANTY BOB S SPACE RACERS INC 90 DAY COIN OPERATED GAME WARRANTY 1 INCLUDED IN THIS WARANTY Bob s Space Racer Inc warrants to the original purchaser only that the equipment that is the subject of this sale conforms to its specifications and is free from defects under normal service for a 90 day period from the original date of deliver This warranty does not include any damages resulting from occurrences listed in paragraph 2 below This warranty is not transferable under any circumstance Any claims under this warranty must be received in writing by Bob s Space Inc within 120 days from date of delivery Within a reasonable time of such written notification Bob s
15. IC TARGET SENSOR ARWB2003 TARGET MAGNET ARWB2004 MARQUEE LIGHT FLASHER UNIT ARWB6001 1 2 HP PUMP ONLY E0025100 12 VOLT COUNTER E0027150 10 FT POWER CORD COMPSTYLE E0028300 TURBO BULB FLASHING LIGHTS E0030630 BEACON LIGHT BASE E0030632 BEACON LIGHT CHROME RING E0030635 RED BEACON LIGHT RED DOME E0070012 CLR LENS BODY FLASHING LIGHTS E0070015 CL CLEAR LENS CAP E0070016 BL BLUE LENS CAP DOT E0070016 RED RED LENS CAP DOT E0070016 YE YELLOW LENS CAP DOT E0800040 WORKHORSE 6 BALLAST E0800041 PL40 FLORESCENT BULB E0800044 BULB RETAINING CLIP E0800070 e X 9 SPEAKER E0800157 DISPLAY P C BOARD E0800201 200 WATT POWER SUPPLY E0800310 SOLID STATE RELAY EX800150 P C BOARD HOLDER E0023880 FUSE 15 AMPS SLO BLO 22 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 WATER BLAST ARCADE MANUAL BOB S SPACE RACERS 5 SCHEMATICS Water Blast Wiring Harness VISNIdSIT 122011 e E3Avd 335434514 2211 I 421914 JAWA Nilv NNI 2 W3AV ld JAWA NNI 83AVTd AVTSSIL 824 21987 NivW 23 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL Board Schematic 1 FF cr is EHI b gt 14 E 8 TT x 213212 a HU p a di us ee His Nm Der E jq amp 4 bie 24 To Purchase This Item Visit BM
16. N THE GROUND FAULT OUTLET ON THE RESET BUTTON MUST BE DEPRESSED DURING GAME PLAY TO BE ACTIVATED PUSHING THE RESET BUTTON WHEN THE GAME IS OVER WILL NOT HAVE ANY PROGRAMMING EFFECT PANEL 5 Hold the drain hose into the 5 gallon pail and press the VALUE button to start the pump 6 Run the pump until ALL of the water empties out of the tank Turn off the pump 7 Turn the GAME DRAIN valve to the GAME position 8 Remove the screen at the bottom of the tank and clean both the tank and the screen Re install the screen 3 3 4 Filling the Water Tank 1 Add 5 gallons of water to a bucket and add 1 TBSP Cascade Dishwashing powder This will help keep the glass clean DO NOT use too much Cascade or foaming will result SUGGESTION ALTHOUGH ANY WATER CAN BE USED USE DISTILLED WATER WHENEVER POSSIBLE DISTILLED WATER HAS ALL OF THE MINERALS REMOVED AND WILL DRASTICALLY EXTEND THE TIME INTERVAL BETWEEN WATER CHANGES 2 Clean the inside of the glass with a plastic scrub pad to remove dirt and sediment from the glass NOTE IF THE GLASS IS BADLY STAINED USE C L R MINERAL REMOVAL SPRAY FIRST TO GET RID OF TOUGH MINERAL DEPOSITS 16 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL 3 Spray RAIN X on the inside of the glass to help prevent minerals from forming on the glass 4 Fill the tank with the 5 gallons of water 5 Set th
17. Space Racers Inc will replace or repair any defective component of the equipment or part thereof which fails for reasons other than normal service use or wear Bob s Space Racers Inc reserves the right to request dated proof of purchase by the end user original purchaser at any time Light bulbs are specifically excluded from this warranty and shall be the sole responsibility of the purchaser Bob s Space Racer Inc within its sole discretion makes the final determination as to whether to repair or replace any component and whether any such repair or replacement shall be performed where the equipment is located or at it s home facility in Volusia County Florida or another facility of its sole choice Any and all freight charges for the purposes of repair or replacement shall be paid by the original purchaser All defective parts shall be returned to Bob s Space Racers Inc if requested Bob s Space Racers Inc does not warrant that the equipment will meet any original purchasers specific requirements or that the operation of the equipment will be uninterrupted These remedies are the original purchaser s exclusive remedies for breach of warranty 2 EXCLUDED BY THIS WARRANTY Bob s Space Racers Inc does not warrant a any product components or parts not manufactured by Bob s Space Racers Inc b damages caused by use of the equipment for purposes other than those for which it was designed c defects caused by failure to provide
18. To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 1 WARNING Be sure to read this Operation Manual before using your machine to ensure safe operation 2008 Bob s Space Racers Incorporated NOVEMBER 2008 SIEGE UPS SPACE RACERS To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL WATER BLAST ARCADE To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL TABLE OF CONTENTS 1 INTRODUCTION 1 1 Overview and Technical Features 1 2 Important Safety Information 2 PROGRAMMING 2 1 Entering Programming Mode 2 2 Volume 2 3 Coins per Credit 2 4 Attract Mode 2 5 Just for Playing Tickets 2 6 Winner Tickets 2 7 Game Time to Win 2 8 Time Out 2 9 Drain Water 2 10 Money 2 11 Reset Defaults 2 12 Programming Options 3 MAINTENANCE AND TROUBLESHOOTING 3 1 Quick Troubleshooting 3 2 Maintenance 3 3 Detailed Troubleshooting and Repair 3 3 1 Changing the Water 3 3 2 Glass Cleaning 3 3 3 Draining the Water Tank 3 3 4 Filling the Water Tank 3 3 5 Water Pump Removal 3 3 6 Water Pump Installation 3 3 7 Cleaning Gun Parts 3 3 8 Target Sensors 3 3 9 Main P C Board Removal and Installation 3 3 10 Display P C Board Removal and Installation 3 3 11
19. a suitable installation environment for the equipment d damage caused by unauthorized attachments modification or service e damage caused by normal wear and tear or improper power supply f damage caused by accident or disaster such as fires flood lightning and wind or g any other abuse or misuse of the equipment 3 EXCLUSIVE WARRANTY THE FORGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES OR REMEDIES WHETHER WRITTEN ORAL OR IMPLIED THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE COURSE OF DEALING OR USAGE OF TRADE ARE HEREBY EXPRESSLY DISCLAIMED AND EXCLUDED 4 REMEDIES LIMITED UNDER NO CIRCUMSTANCES EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW SHALL BOB S SPACE RACERS INC BE LIABLE FOR ANY LOSS OR DAMAGE DIRECT OR INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL ARISING OUT OF THE USE OR INABILITY TO USE THIS EQUIPMENT INCLUDING BUT NOT LIMITED TO ANY CLAIM FOR LOSS OR PROFITS LOSS OF SAVINGS OR REVENUE LOSS OF USE OF THE EQUIPMENT OR ANY ASSOCIATED EQUIPMENT FACILITIES OR SERVICE DOWNTIME THE CLAIMS OR COSTS OF THIRD PARTIES INCLUDING CUSTOMERS AND INJURY TO PROPERTY Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations or exclusion may not apply to you This warranty gives
20. e game s GAME DRAIN valve to the drain position 16 Press the PROGRAM button on the game s programming panel to access the programming options 17 Press the SELECT button and advance to the DRAIN option GAME DRAIN lt PROGRAMMING PANEL 18 Press the VALUE button to turn the pump on and off NOTE THE PUMP IS RUN ON A GROUND FAULT INTERRUPTER CIRCUIT THIS IS TO PROVIDE A HIGH DEGREE OF SAFETY TO THE CUSTOMER IF THE PUMP DOES NOT RUN WHEN THE GAME IS STARTED CHECK THE RESET BUTTON ON THE GROUND FAULT OUTLET ON THE RESET BUTTON MUST BE DEPRESSED DURING GAME PLAY TO BE ACTIVATED PUSHING THE RESET BUTTON WHEN THE GAME IS OVER WILL NOT HAVE ANY EFFECT 19 Hold the drain hose into the 5 gallon pail and press the VALUE button to start the pump 20 Run the pump until the water comes out of the drain hose clear TURN PUMP OFF 21 Turn the GAME DRAIN valve to the GAME position 22 Start a 2 player game and check for proper operation of the guns WATER BLAST ARCADE MANUAL NOTE IT IS NORMAL FOR THE GUNS TO SPUTTER DURING THE FIRST GAME UNTIL ALL OF THE AIR IS PURGED FROM THE HOSES AND LINES 23 Adjust the programming options as needed To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL 2 PROGRAMMING 2 1 ENTERING PROGRAMMING MODE The programming options are readable only by the
21. e game s GAME DRAIN valve to the drain position 6 Press the PROGRAM button on the game s programming panel to access the programming options 7 Press the SELECT button and advance to the DRAIN option 8 Press the VALUE button to turn the pump on and off 9 Hold the drain hose into the 5 gallon pail and press the VALUE button to start the pump 10 Run the pump until the water comes out 11 Turn the GAME DRAIN valve to the GAME position 12 Play a couple of 2 player games to remove all of the air from the system 3 3 5 Water Pump Removal 1 DRAIN TANK AS DIRECTED ABOVE 2 Open the front doors of the game and remove the bolts that hold the seat base to the game See image to the right i j 3 Move the seat assembly out of the way VI Z cim 4 Remove the cash box and remove the single bolt located in the bottom of the cash box enclosure See image below SEAT BASE BOLTS 5 Slide the cash box enclosure out of the game and unplug the programming panel connector Set the cash box enclosure to the side 6 Carefully slide the pump assembly forward to access the pump See image below ASSEMBLY 17 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL 7 Unplug the solenoid harnesses and the A C Motor plug from the outlet in the upper left hand side of the cabinet See imag
22. e pump until the water comes out 19 Turn the GAME DRAIN valve to the GAME position put 5 gallons of fresh water in game 15 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL WARNING BEFORE SLIDING PUMP INTO PLACE PLAY THE GAME CHECKING FOR WATER LEAKS AS THIS WILL CAUSE SEVER DAMAGE TO GAME 3 3 2 Glass Cleaning 1 Clean the inside of the glass with a plastic scrub pad to remove dirt and sediment from the glass DO NOT use any steel wool or scotch bright pads as these will damage the plastic side glass panels NOTE IF THE GLASS IS BADLY STAINED USE C L R MINERAL REMOVAL SPRAY FIRST TO GET RID OF TOUGH MINERAL DESPOSITS 2 Spray RAIN X on the inside of the glass to help prevent minerals from forming on the glass 3 Clean the outside of the glass with any good commercial glass cleaner 3 3 3 Draining the Water 1 Set the game s GAME DRAIN valve to the drain position ht T 2 Press the PROGRAM button on the game s programming panel to zh DRAIN access the programming options N 3 Press the SELECT button advance the DRAIN option 4 Press the VALUE button to turn the pump on and off NOTE THE PUMP IS RUN ON A GROUND FAULT INTERRUPTER CIRCUIT THIS IS TO PROVIDE A HIGH DEGREE OF SAFETY TO THE CUSTOMER IF THE PUMP DOES NOT RUN WHEN THE GAME IS STARTED CHECK THE RESET BUTTON O
23. e to the right NOTE SERVICING OF THE SOLENOID VALVES CAN BE COMPLETED AT THIS STAGE OF REMOVAL FOR FURTHER SERVICE CONTINUE TO REMOVE THE PUMP ASSEMBLY HAVE A SPONGE OR TOWEL AND SMALL BUCKET HANDY TO CATCH ANY DRIPS FROM THE HOSES 8 Unscrew the small black hoses from the guns at the solenoids Wipe up any drips from the hoses 9 Carefully pull the pump unit out of the game 10 With a sharp knife cut the large feed hose and small return hose as close to the pump fittings as possible IT IS NECESSARY TO CUT THE HOSES OFF AS IT IS TOO DIFFICULT TO TRY TO PULL THEM OFF OF THE FITTINGS SOLENOID VALVES 11 Remove the hose clamps and cut the remaining pieces of hose from the pump fittings THE PUMP ASSEMBLY CAN NOW BE SERVICED OR REPLACED REPLACE ANY NECESSARY COMPONENTS MAKING SURE THAT ALL FITTINGS ARE SEALED WITH TEFLON TAPE 3 3 6 Water Pump Installation 1 Connect the feed and return hoses to the pump assembly Leave the RETURN hose clamps loose at this time HOSE i rr gt 2 Slide the pump assembly back into the unit until it hits the rear stop dac 3 Adjust the hoses to be sure that there are no kinks at all in the hoses If there are any kinks rotating the hoses will usually remove them 4 TIGHTEN THE HOSE CLAMPS 5 Reconnect the A C plug making sure that it is routed out of the way behind ticket bin 6 Re install the solenoid harnesses by plugging in the connect
24. em 27 Re plug power and turn on Play a test game to make sure game is working properly IF YOU HAVE ANY QUESTIONS OR COMMENTS PLEASE CALL OUR SERVICE DEPARTMENT AT 1 386 677 0761 or EMAIL QUESTIONS TO Tech BobsSpaceRacers com 37
25. l or no water Faulty solenoid valve GFI circuit tripped Faulty Pump Faulty Main P C board Clean nozzle with paper clip Check hoses for kinks Check water level and fill if necessary Check or replace solenoid valve Start game and push GFI reset button Repair or replace pump Repair or replace Main P C Board Programming button and counters Disconnected programming Panel harness Check connector Check connector 13 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL 3 2 Maintenance Daily Maintenance 1 TURN ON GAME POWER SWITCH 2 PHYSICALLY CHECK WATER LEVEL IN WATER TANK IF THE WATER IS LOW OR BELOW THE FILL LINE FILL THE TANK MAKE SURE THERE IS A MINIMUM OF 5 GALLONS IN THE TANK AT ALL TIMES AND THE WATER IS ABOVE THE FILL LINE FOR INSTUCTIONS ON HOW TO FILL THE TANK SEE THE FILLING THE WATER TANK SECTION 3 CHECK TICKET LEVELS IN TICKET DISPENCERS BEFORE OPENING EACH DAY 4 CLEAN WIPE DOWN AND DRY OFF GAME NIGHTLY OR AS NEEDED 5 CHECK ALL LIGHT BULBS FOR WORKING ORDER THIS INCLUDES TARGET PAN LIGHTS TARGET 6 ITIS RECOMMENDED THAT YOU CLEAN THE WATER FILTER EVERY THREE DAYS OR AS NEEDED DEPENDING ON WATER CONDITIONS Weekly Maintenance 1 CHECK THE WATER SYSTEM FOR DIRT AND DEBRIS 2 ITIS RECOMMENDED THAT YOU CHANGE THE WATER SUPPLY ONCE A WEEK OR AS NEEDED DEPENDING ON W
26. neral guidelines should be followed 1 Always check to be sure that you game is turned on Be sure that all of the fuses in the game are functional and check to see that the AC voltage is in the proper operating range for your game 2 Check to be sure that all of the game harnessing is plugged in properly and that all of the pins are firmly seated in the connectors It is always possible that a harness can be damaged by rough shipping or moving 3 Check game harnessing to be sure that none of the wires have become damaged Using a handheld multi meter check continuity of the wires to make sure they are not broken 4 Check for obvious damage to any P C Boards or electrical components 5 If you have multiple games or multiple parts on a game change or exchange the parts and see if the problem goes away or moves to another location This way you can quickly eliminate certain parts as being the problem with the game 6 When changing electronic or electrical components ALWAYS turn off and unplug the game 7 Check to see that all power supplies are delivering the specified voltages to the P C Boards and components as shown in the manual For detailed servicing and repair information see the full the full repair section of this manual 12 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL Symptom Possible Problem Solution
27. ng www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS GAME PLAY The object of the game is to shoot water from the gun into a target pan making the display indicator rise to the top of the game to win The game can be played by 1 or 2 players The game is designed to be played in a traditional player versus player RACE or as a SINGLE player game if there is no one available to compete with When the game is idle it will normally say INSERT COIN S on each display Unless it is playing the attract mode When a player puts enough money into the game to start the display on his side will say GET READY and the other side will still say INSERT COIN S Under the side with get ready a count down from 15 0 will be visible Once both players have inserted enough money to play the count down will continue and the game will start when the timer runs out OR as soon as the start button is pushed If one player has started a game and a second player walks up to play and inserts money the display on his side will flash WAIT until the game in progress has ended At that time the previous game play scenario will begin In a 2 player RACE game the winning player will win BOTH of the WINNING share of tickets and the JUST FOR PLAYING tickets while the loser will win only the JUST FOR PLAYING tickets For example The game is set for 3 tickets JUST FOR PLAYING and 5 tickets for WINNING In a single playe
28. or a Card Swipe The options for this setting are 0 or 1 0 sets the game up for Coin Play while 1 sets the game up for a Card Swipe 0 is the factory default for the Money option 2 11 RESET Default programming value reset This option will reset the game to factory default values The range for this option is 0 1 Setting a 1 will reset the values to factory default The default value for this option is O 2 12 PROGRAMMING OPTIONS REGISTER Min Max BSR DESCRIPTION Volume 1 10 3 Volume Control Coins Credit 1 10 1 Number of Coins per Game Attract Mode 1 5 3 Minutes Between Bally Music Default Tickets 0 10 3 Tickets Just for Playing Winner Tickets 0 30 5 Winning Tickets Per game Time to Win 5 20 12 Time to Win in Seconds Time Out 0 10 20 10 Time of Inactivity Auto Win Money 0 1 0 Coin play 0 or card swipe play 1 Drain Water 0 1 On Off Pump ON OFF Manual Reset Defaults 0 1 0 Reset Factory Default Settings 11 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL 3 MAINTENANCE AND TROUBLESHOOTING 3 1 Quick Troubleshooting AS WARNING For your safety and to reduce risk of damage to your game read the Important Safety Information in Chapter 1 2 before attempting any troubleshooting procedure TROUBLESHOOTING PHILOSOPHY When troubleshooting any product certain ge
29. ors NOTE THE HARNESS MARKED 161 GOES TO THE LEFT HAND SIDE AND THE HARNESS MARKED 162 GOES TO THE RIGHT HAND SIDE 7 Re install the cash box enclosure and reconnect the programming panel harness by plugging in the connector 8 Re install the small black hoses from the solenoid valves to the guns 9 FILL THE WATER TANK AS DIRECTED ABOVE 10 Re install the cash box and bolt 11 Re install the seat assembly and bolts 18 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL 3 3 7 Cleaning Gun Parts It is possible after extended periods of time or if the water you use is very high in mineral content that you may have to clean deposits or debris from the gun assembly 1 To clean the gun tip try cleaning with a paper clip first If that doesn t work unscrew the tip to clean See image to the right 2 For larger debris unscrew the gun assembly from the top of the control panel Disconnect the spring from underneath See image below GUN TIP GUN P ASSEMBLY 3 Remove the hose and nozzle tip from the gun SCREWS 4 Run a coat hanger or thick wire through the gun passages to remove any blockage 5 With the tip off the gun re install the gun and connect the hose 6 Play a few games to allow any debris to escape the gun body 7 Re install the gun tip and check for proper operation 3 3 8 Target Senso
30. r game the player wins 8 tickets period once he or she wins In a 2 player game the winner would get the 8 tickets PLUS the 5 win tickets from the loser for a total of 13 tickets The loser would get the 3 tickets just for playing At the end of the game WINNER will flash on the winning side OR when ever the player gets to the top on the single player game type The beacon light will also rotate when winner is flashing WATER BLAST ARCADE MANUAL To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS 1 2 Important Safety Information IMPORTANT SAFETY INFORMATION WARNING Unplug the game from the AC wall receptacle when servicing this product Failure to do so could result in serious injury to yourself or others Use only a GROUNDED AC receptacle Failure to do so could result in improper operation or damage to the game and could void your warranty If you are unsure that your AC receptacle is properly grounded have a qualified electrician perform this check for you Always be sure power to the game is turned off when doing even routine maintenance Otherwise moving parts could activate unexpectedly causing injury This product is heavy necessitated by the design When moving this game be sure you have adequate help Use a suitable dolly or hand truck where practical Use back support when needed Depending on the potentially hazardous degrees the te
31. rms of WARNING etc are used Be sure to understand the content of the displays before reading the text WATER BLAST ARCADE MANUAL NOTE ONLY QUALIFIED TECHNICAL PERSONNEL SHOULD WORK ON THIS GAME FAILING TO COMPLY CAN CAUSE SEVERE INJURY SET UP 1 Clear out a location to place the game 2 Remove all packaging from the game 3 Remove the seat base from the top of the game by removing the 2 bolts holding it to the back door NOTE DO NOT DISCARD THE BOLTS YOU WILL NEED THEM TO ATTACH THE SEAT BASE TO THE GAME NOTE ALTHOUGH ALMOST ALL MAINTENANCE IS DONE FROM THE FRONT OF THE GAME WE WOULD RECOMMEND PLACING THE GAME AT LEAST 12 FROM THE WALL IN CASE IT IS NECESSARY TO ACCESS THE REAR PANELS WARNING TO AVOID INJURY TO YOURSELF OR OTHERS WE RECOMMEND THAT YOU HAVE AT LEAST 2 PEOPLE HELP TO SUPPORT THE REAR OF THE GAME WHILE CONNECTING THE FASTENERS 4 Place the game in its final location and slowly raise the game into its upright position To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS 5 While 2 people hold the game vertically open the coin door using the keys taped inside the return slot 6 Remove the cash box to retrieve the connecting bolts and power cord 7 Push the upper cabinet fully back and secure the upper cabinet with the 4 mounting bolts and washers supplied MOUNTING BOLT
32. rs 1 Remove the lower rear access door See image to the right 2 Unscrew the target pan from the game See image below TARGET _ MAGNETIG SENSOR 3 Unscrew the magnetic sensor from the clear polycarbonate window See image to the right 4 Unplug the sensor 19 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL 5 Re install the new sensor using the other sensor as a guide to proper positioning See image to the right 6 Check for proper alignment between the magnetic sensor and the magnet that is located on the target arm 7 Re install the target pan 8 Play a couple of games to check for proper operation 9 Re install the lower rear access door SENSOR POSITIONING 3 3 9 Main P C Board Removal and Installation ALTHOUGH THE MAIN P C BOARD CAN BE REMOVED THROUGH THE FRONT DOOR WITH THE SEAT AND CASH BOX ENCLOSURE IN PLACE IT IS MUCH EASIER TO DO SO IF THEY ARE REMOVED FIRST TO REMOVE THEM FOLLOW THE INSTRUCTIONS BELOW WARNING BE SURE TO UNPLUG THE GAME BEFORE SERVICING TO AVOID SERIOUS INJURY OR DAMAGE TO THE GAME 1 Open the front doors of the game and remove the bolts that hold the seat base to the game 2 Move the seat assembly out of the way 3 Remove the cash box and remove the single bolt located in the bottom of the cash box enclosure 4 Slide the cash box enclosure out of
33. st at his her own expense bring or ship the equipment to an authorized location for service Additionally the original purchaser must pay all freight shipping or transportation charges for the return of the equipment from Bob s Space Racers Inc to the original purchaser Telephone or write Bob s Space Racers Inc 427 15 Street Daytona Beach FL 32117 Telephone number 386 677 0761 FAX 386 677 0794 27 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL WHEN CALLING FOR SERVICE 1 When calling for service please check the service manual first Many times the answer to your problem has been addressed in this documentation 2 Please make sure you have the serial number of the game ready when you call 3 If this is a repeat call please tell the service technician that you have made a previous call regarding this problem This way we will be able to retrieve the history on your game allowing us to serve you better and save you time 4 Please retain proof of purchase for your product This might be requested for warranty repairs 5 Please call from the game if possible since we might need you to check certain things on the game while we are on the telephone with you IF YOU HAVE ANY QUESTIONS OR COMMENTS PLEASE CALL OUR SERVICE DEPARTMENT AT 386 677 0761 MONDAY FRIDAY 8 30AM 5 00PM EST EXCLUDING HOLIDAYS
34. the game and unplug the programming panel connector Set the cash box enclosure to the side 5 Unplug all of the connectors from the Main P C Board See image to the right 6 Unscrew the retaining clamp on the board mounting bracket and remove the board 7 Install a new P C Board making sure that the board engages the slots MAIN P C BOARD on the bottom of the mounting bracket 8 Tighten the P C Board retaining clamp NOTE BE SURE THE CLAMP IS NOT CONTACTING ANY COMPONENTS ON THE BOARD OR SERIOUS DAMAGE MAY RESULT 9 Re install all of the connectors Be sure they are inserted properly and that all of the connector locks are snapped into place 10 Re install the cash box 11 Re install the seat assembly 3 3 10 Display P C Board Removal and Installation ALTHOUGH THE CONNECTORS FOR THE DISPLAY P C BOARD CAN BE REMOVED THROUGH THE FRONT DOOR WITH THE SEAT AND CASH BOX ENCLOSURE IN PLACE IT IS MUCH EASIER TO DO SO IF THEY ARE REMOVED FIRST TO REMOVE THEM FOLLOW THE INSTRUCTIONS BELOW 20 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL WARNING BE SURE TO UNPLUG THE GAME BEFORE SERVICING TO AVOID SERIOUS INJURY OR DAMAGE TO THE GAME 1 Open the front doors of the game and remove the bolt that holds the seat base to the game 2 Move the seat assembly out of the way DISPLAY 3 Remove the cash box
35. ump from AC power outlet in game 34 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL 13 Unscrew the Clear Vu filter Image 7 IMAGE 7 14 Clean the bowl and the filter cartridge using a soft brush and mild detergent S Image 8 2 7 15 Carefully insert the filter cartridge into the base and screw on the bowl DO NOT OVER TIGHTEN 16 Plug the pump into AC power outlet in game 35 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL 17 Fill tank to the FILL LINE The water should be 6 inches deep minimum Image 3 IMAGE 9 gt E 18 up the game and press PUSH TO START 19 Play the game a few times to let the pump circulate the water 20 INSPECT THE PUMP FOR ANY LEAKS before installing in the game Image 10 21 Slide Pump Assembly back into the game 22 Slide the Coin Box Assembly back into the game 36 To Purchase This Item Visit BMI Gaming www bmigaming com 800 746 2255 1 561 391 7200 BOB S SPACE RACERS WATER BLAST ARCADE MANUAL 23 Install Allen bolt in bottom of Coin Box Assembly 24 Install Coin Drawer 25 Inspect the inside of the game for any loose wires or water damage before closing IMAGE 11 26 Shut the Coin Ticket doors and lock th
36. you specific legal rights and you may also have other rights which vary from state to state 5 NO OTHER WARRANTIES Unless modified in writing and signed by both parties this agreement is understood to be the complete and exclusive agreement between the parties superseding all prior agreements oral or written and all other communications between the parties relating to the subject matter of this agreement No employee or representative of Bob s Space Racers Inc or any other party is authorized to make any other warranty or to assume any other liability in connection with the sale of its equipment 6 TIME LIMIT FOR CLAIMS Any claim for breach of warranty or claims under this warranty must be received in writing by Bob s Space Racers Inc within 120 days following delivery of the equipment 7 FUTURE CHANGES Bob s Space Racers Inc reserves the right to reserve change or modify the construction and design of its equipment or any component part or parts thereof without incurring the obligations to make such changes or modifications in present equipment 8 ALLOCATION OF RISKS This agreement allocates the risks of equipment failure between Bob s Space Racer Inc and the original purchaser This allocation is recognized by both parties and is reflected in the price of the goods THE PURCHASER ACKNOWLEDGES THAT IT HAS READ THIS AGREEMENT UNDERSTANDS IT AND IS BOUND BY ITS TERMS 9 TO OBTAIN WARRANTY SERVICE The original purchaser mu
Download Pdf Manuals
Related Search