1999-2003 Ford F-Series 7.3L Power Stroke Edge
Contents
1. Lvl 1 Tow Lvi 2 Race Lvl 3 Extreme gt a 1 Select the level that best meets your needs For more information about each level read the About the Evolution section in this manual Confirm your selection by pressing ENTER on the screen that will follow After confirming the screen below will appear lam Create a custom program No Yes 2 After your initial tune you have the option to change certain parameters of the level you chose If you would like to learn more about what parameters are available and how to use them then read the Custom Options sections in this manual To use the standard program without customizing options simply press ENTER choose NO 3 The Evolution will ask you to turn the key OFF and then ON Do NOT crank the engine or possible programming failure may result 4 During the first use the Evolution will read the original calibration from your PCM and then build all the necessary programs This step 1s skipped during all further programming operations except when returning the vehicle to stock 5 The Evolution will erase your PCM and then write the selected calibration level onto the PCM If at any time you receive an error message refer to the Troubleshooting section at the back of this manual for further instructions 6 When the Evolution is done programming continue to follow the directions on the screen The following screen will appear and y2. 2 Function Digital 3 Function Digital 4 Function Digital 1 E JAdjust LCD Settings 3 Select the Adjust LCD Settings option The following screen appears Change LED Color Red 50 Green 100 Blue 0 Contrast 35 4 Select Contrast and use the up and down arrows to adjust the contrast to where you d like If you would like to know when a certain parameter reaches a certain value you can set an alert for that parameter by following these steps Following is a list of Alerts you may set and adjust a EGT Alert d EngOilTmp Alert b Speed Alert e TransTmp Alert c RPM Alert f Boost Alert 1 From the Main Menu select the Setup option The Setup screen appears as follows 32 Evolution FORD 7 3 Liter Setup Display Alerts Records Reset Evo Settings Alerts are CHF EGT Alert 1400 Speed Alert 85 RPM Alert 4000 EngOllTmp Alert 250 3 By default the alerts are off To turn them on select the Alerts are Off option and press ENTER The text line will now read Alerts are On To change the value of a certain alert select the parameter you want to change and press ENTER A screen similar to the following will appear ps D i l Speed Alert 85 Press lt ENi gt to set value 4 Press the UP and DOWN arrow keys until you have reached the desired v
3. Eymur 1999 2003 Ford F Series 7 3L Power Stroke Edge Evolution Programmer Installation Instructions amp Manual P N 15001 READ IMPORTANT SAFETY INFORMATION IN THIS MANUAL Evolution FORD 7 3 Liter TABLE OF CONTENTS IMPORTANT SAFETY INFORMATION ecce eee eee ee eene eene eene t ehe e eese teet eene nun 3 SAFELY M O1 1L oer eins 3 SAFETY GUIDELINES ten 3 PRODUCT REGISTRATION inii a ie EE EE E NES 4 Benefits OF product reist ration iei ies eee ura Fe eere reca a ao eee YE NN EE YE eee Ee ENS NE EN EER EYE SENSN ERE a 4 About the EVOM ON c i EEOAE teo east eaters 5 StOCk Pro T ahi sisaan 6 Tow Only PROGRAM 41 nae eC AONE 6 Race Performance PEOPEAHIS i esie eo C Yea Spe a EUIS PEOR eub eeu Uso fe UNS S eaS 6 Extreme Performance PEOSEQID ien ete ede Ere REA EN RXN IU EET ER REL PRINS NNUEX EFE EHIS E RETE ENE SE ERE 6 Fower Gali m n 6 17 17 02 mm 7 ID o M 7 Birra CGS e A AA E AAN 7 0 60 and OUr M e E a aa a a a a aa a S 7 ALET a a E a ne 8 S 0 6 SHEN RTT TR TT TT a a eee 8 Custom OPON dito mob eumd EDD UM IM NU EI eto M coL UU M USD 8 Display and Keypad reres e a E E OE EEOSE RERE 8 Getinge Connected vatican NE ERI ee ia 9 Installing the EGT Thermocouple sisescciscecscecsssscccesensasvacteoccc
4. must still obey all driving laws including adhering to posted speed limits CAUTION Setting this value too high can cause damage to your engine Adjusting the rev limiter for purposes inconsistent with the product s intended function violates the product s intended use and will invalidate the product s warranty Edge Products is not responsible for or liable for the consequences of improper product use Hint Make sure to set the Rev Limiter at least 150 RPM higher than the highest WOT Shift Point or you may experience erratic shifting Timing Adjustment This adjustment changes the injection timing in increments of 25 degree CAUTION This option should not be used unless you have experience in tuning trucks for performance If used in conjunction with fuel modifiers the customer must carefully consider the risks and understand the potential impact on the engine and its components Hint Edge recommends this option be left unchanged and set at 0 Timing change may be useful to help lower EGT s WOT Wide Open Throttle Shifting On automatic transmissions these are the RPM points at which the vehicle will shift when you are at Wide Open full Throttle Raising these values helps to keep the engine in the peak power curve after a shift 20 Evolution FORD 7 3 Liter Hint Raising these values may help improve 0 60 and quarter mile times Standard Std Shifting On automatic transmissions these are the MPH points
5. Also since exhaust manifolds can be very hot allow the engine to cool before drilling When working under the vehicle make sure the park brake is set If the vehicle must be raised carefully follow the stand and vehicle safety guidelines for placement and use of jacks and stands CAUTION One effective way to avoid metal fragment contamination in your engine manifold is to apply grease in the tip of the drill bit and threads of your tap tool when drilling tapping the hole in your manifold Reduce pressure on the drill when the drill breaks through the manifold wall to reduce risk of pushing metal chips into the manifold Ford 7 3 Liter Evolution 1 To install the EGT probe first determine where you will drill the hole The section of the exhaust manifold that requires tapping 1s located on the driver s side just above the driveline This photo shows the underside of the truck looking up en Faye S 1 3332 vu A L r E j d j fe 4 j b i 4 a i y El a p i a _ LT Looking up at the exhaust manifold from under the vehicle The rear of the vehicle is to the top of the picture and the front is to the bottom 4 kk 2 Obtain a 1 8 National Pipe Tap NPT available from your hardware store Drill a 21 64 5 16 optional hole through the manifold wall and then use the pipe tap to cut the threads Follow the instructions provided with the tap The pipe tap 1s tapered s
6. rev limiter and speed limiter are also parameters that you can change while programming your vehicle Display and Keypad The following picture is a sample Evolution screen Great effort has gone into making the Evolution programmer very simple to use The UP and DOWN arrow keys are used to scroll through options on the screen The ENTER key is used to select desired options from a menu or move to the next screen The MENU key is used to enter the Main Menu from the parameter display or return to the previous screen This version of the Evolution also has the option to change the backlighting color of the display to a wide range of colors NOTE The Evolution uses a LCD display which has inherent limitations in operating temperature If your screen is black blank or distorted and the temperature is above 156 degrees F 70 degrees C please allow the device to cool and then it should work correctly At extreme low temperatures 32 degrees F or 0 degrees C the display will update very slowly Again wait for the device to warm to normal operating temperatures for the screen to function properly Evolution FORD 7 3 Liter Main Menu Power Programming Diagnostics Perforance Tests Setup Getting Connected Installing the EGT Thermocouple WARNING When installing the EGT Thermocouple wear eye protection and protective clothing to protect from getting metal chips in your eyes
7. 7 3 Liter Evolution Four Function Digital Display Sample E Changing the Variables on the Screen To change the variables on the screen perform the following steps 1 From the Main Menu select the Setup option The Setup screen appears as follows Setup Display Alerts Records Reset Evo Settings 2 Select the Display option The following screen appears ca Display f 2 Fanction Bar Graph Can 2 Function Digital 3 Fanction Digital Cm ss 4 Function Digital Lo Adjust LCD Settings 3 Select the style which you would like the parameters to be displayed on your screen and press ENTER Depending on which display you select a screen similar to the following appears 28 Evolution FORD 7 3 Liter Select Parameter to edit RPM Top Left BST Bot Left MPH Top Right Cw EGT Bot Right Set as display 4 This screen lists the current parameters being displayed and their respective positions on the screen 1 e TOP LEFT etc Select the position you would like to change and press ENTER A list of available parameters will be displayed Select the parameter you would like to view and press ENTER A list of commonly used acronyms is located in the back of this manual and an in depth list of PIDs supported follows Once you have selected your desired parameters select the Set as Display option and press ENTER You will ret
8. Do F vr RR H RR ENEE 26 Two Function Bar Graph Display Sample eee e ecce esee eee ee ee eee eeeeouus 27 Two Function Digital Display Sample ecce ee eee eee eee ee eee eese ee esesssnus 27 Three Function Digital Display Sample 4c ccce ecce eee e eee eee e eene ee eee e tette ee eeosus 27 Four Function Digital Display Sample eee ee eee eee eee eee eese eese esse ssesss ss scoos 28 Changing the Variables on the SCreGW sci sssscssss eoe u oe pee eo Ree aUo e Repo e eae oe Y YE e ape e aie eR NY Een epa ESSE SER v EE ea Tuo 28 Changing the B cklip H BEB escossctsereinem ni ia ie eeu Evo osea evE SS E END UNRE UE EP ERUN IIa POR ETE EUN IEEI 30 Adjusting the Backlight Color Contrast 4 e e eee ee ee eee eee eee eee e eee ee e eee eene 30 Adjusting the Backlight Brightness 411 Lee Leere eee eee e eee ee eee ee eee estes esee s ssssase 31 Adjsaing the OM AS Lco cesccsewescasssesviececesssasseeiveccuce se czesssocecussaysessesesccusedeseeseececessceseseesoscecsssies 31 ZHORIS siu INUENIT M NUN NI MEINE 32 I 2 01 7 m 34 KOSA LOS TT 34 PU SUOMI SUR T1177 0 36 Internet Connection Required to Update cce ee
9. Tests Setup 2 Select the Performance Tests option The following screen appears 24 Evolution FORD 7 3 Liter G5 Performance Tests 0 60 1 4 mile 3 Select the desired performance test 0 60 screen is shown below If your vehicle is moving at this time the Evolution will ask you to come to a stop 4 For the 0 60 MPH run press the accelerator pedal and the test automatically begins For the 4 mile test you will be asked to press a key when ready It will then cycle through a starting light sequence Christmas tree and tell you when to go As you drive the screen should be displaying your current speed When the test is complete the desired distance or speed is reached the test will automatically stop and your time will be displayed on the screen as follows quarter mile result example 0 93s REACT TIME 1 4 mi This will show how long it took you to cover 60 feet 1 8 mile and 4 mile In addition your MPH at 4 mile will also be shown see the example above The best run is stored for later viewing You may also use the back of this manual to write down your times At the end of a 4 mile run you will see a reaction time at the top of the screen This time begins when the final yellow light is displayed The time between the 25 Ford 7 3 Liter Evolution final yellow and the green is a 2 second so a perfect reaction time is a 2 second The average person will see a respo
10. and firmly press down on the brackets through the front of the pod to secure the Velcro in place 8 After the pod is secure insert and seat the rubber gasket into the Pod opening Disconnect the cable at the OBDII port and attach the Evolution to the cable end which 1s protruding from the Pod Figure 6 9 Insert the Evolution into the Pod Any excess cable may be stuffed behind the Evolution or may be pulled back through the dash to eliminate slack The result of the installation 1s shown in Figure Z7 Be sure to use the supplied cable ties to secure any excess cable underneath the dash to prevent the cable interfering with proper pedal operation 14 Evolution FORD 7 3 Liter Figure 7 NOTE f you are not satisfied with the pod color match to your interior an automotive paint supply store should be able to provide color matching information and a plastic compatible paint to match any color interior 10 Locate the Thermocouple cable connector which was previously passed through the firewall and plug into the 4 pin terminal protruding from the end of the Edge Products OBDII cable See figure 8 Note This view shows the Edge Products OBDII cable installed on the truck OBDII port Do not plug into port until instructed in the next step Figure 8 15 Ford 7 3 Liter Evolution With the Pod and Evolution securely in place turn the ignition key ON and then plug the Edge Products OBDII cable into the OBDII connec
11. at which the vehicle will want to shift during normal acceleration Positive values will cause later shifts while negative values will cause shifts to occur sooner Hint Negative values may help improve fuel economy while positive values will improve performance Shift Firmness On automatic transmissions these values represent a percentage change in shift firmness or in other words how hard your transmission will shift A positive number will cause the shift to be firmer A negative number will cause it to be softer Hint Firming up the shifts may help improve 0 60 and quarter mile times WOT Fueling If you have added an exhaust and or intake to your vehicle often times you will need more fuel at Wide Open Throttle You can use this custom option to add subtract WOT fueling to maximize performance Idle Speed RPM This adjustment modifies the base Idle Speed of the engine in increments of 25 RPM Select the RPM you would like to add to the base idle speed For example if the normal base idle 1s 600 RPM and you want 625 RPM set the value to 25 RPM 600 25 625 This option will only raise base idle not lower it Idle speeds above 600 RPM may cause vehicles with automatic transmissions to creep when stopped while in gear requiring additional pressure on the brake pedal in order to keep the vehicle stationary Hint This value may be useful where vehicles may experience extended idle times Raising the idle helps
12. eee Lecce eere eee ee eee ee eee eee eese 36 Possible Prosramminp Errors sisses hei Io PRESE EpERIBEENY FER UR E S CEHE NN EE ERE E EVA SHIT EN XY EL Ere ea eo TRE Hao PES DH ES 37 Torne noon n gr e 38 Marran LIMIT REN teswesuceuisanuescaversensieedcesepunsueaceronvsausuaceeeeinetieccsues 40 LIMITED L YEAR WARRANTY sssscscsesscdsccisscssesstvcesiesicacssvatssdeasasecesssstvansdssieavssssnsesssseasiceeise 40 Commonty U SCG A CON HS sesseur ennei EEE VIP OD UI EI Te Eb EUI II IPOUE 42 Technical Suppor e A 42 02000 Edge Products All rights reserved Edge Products 1080 South Depot Dr Ogden UT 84404 1 888 360 3343 Www edgeproducts com Manual Version 19 Evolution FORD 7 3 Liter IMPORTANT SAFETY INFORMATION SAFETY TERMS Throughout this User Guide hereafter referred to as User Manual or Manual you will see important messages regarding your safety or the protection of your vehicle These messages will be designated by the words WARNING or CAUTION H WARNING indicates a condition that may cause serious injury or death to you your passengers or others nearby Pay careful attention to these Warning messages and always comply with them They could save a life CAUTION indicates a condition that could cause damage to your vehicle It is important to install and operate your EDGE product in conformance with instructions in this Manual Caution messages alert you to
13. improper installation could cause powertrain failure on the road Other products may have features incompatible with your Edge device Follow all installation and operating instructions and don t stack products 5 Some modifications may affect other parts of your vehicle For example if you remove agjust the speed limiter in your vehicle be sure your tires and other components are rated for the increased speeds they will have to withstand Not doing so can lead to loss of vehicle control Modify the speed limiter only for use in closed circuit legally sanctioned racing environments not for use on public roadways 6 Do not use the Performance Tests feature to break any traffic laws Perform these tests only where they are legal and safe Ford 7 3 Liter Evolution 7 Some features may not function on all vehicle models Check a newly installed device for all features you intend to use Do not rely on their working without checking first NOTE Dispose of this product consistent with local codes Return to your electronics supplier for proper handling PRODUCT REGISTRATION Please take the time to register your product To register your product follow the Benefits of product registration e Your Safety registering your product allows us to know exactly which product you have and provide important product updates to you that improve the quality and or safety of the product e Enhanced Features almost all Edge products are
14. keep the cylinder temperatures up and prevents a condition called wet stacking which is the buildup of unburnt fuel deposits on the back of the exhaust valves Over time this condition can cause loss of performance Diagnostics The diagnostics scanner included with your Evolution 1s a powerful tool that allows you to view and clear diagnostic trouble codes DTCs on your vehicle DTCs are the messages your vehicle s computer stores when it detects a problem with your vehicle The Check Engine light on your dash is activated by the presence of most DTCs If you selected Diagnostics from the main menu of the Evolution the screen displays the following message 21 Ford 7 3 Liter Evolution Diagnostics Retrieve DTCs Clear DTCs Tech Support Retrieving Codes If you want to retrieve and view the DTCs on your vehicle select the Retrieve option Make sure your ignition is in the ON position After selecting the Retrieve DTCs option any stored DTCs will appear on the screen like the following example Code 1 of X CODE DESCRIPTION No Trouble Codes Found Press any key Press MENU to exit the DTC list and return to the previous menu Clearing Codes If you want to clear the DTCs on your vehicle select the Clear DTCs option 22 Evolution FORD 7 3 Liter After selecting the Clear DTCs option any current stored DTCs will be cleared from your vehicle and the Check Engine light will g
15. product connected may affect dealer diagnostic analysis and CAN tool functions Edge makes every effort to produce product that can be easily removed NOTE Even if you disconnect your unit your dealer can detect the use of any programmer even if the unit has been removed Thank you for purchasing the Evolution by Edge Products LLC for the Ford 7 3 Powerstroke Diesel The Evolution programmer has been developed and produced from the highest quality materials available to ensure the best performance for years to come If you have any concerns or questions please contact us Note This warranty is void for any new products purchased through auction websites Warranty is valid only for new products purchased through Authorized Dealers proof of purchase required for all warranty claims 41 Ford 7 3 Liter Evolution Commonly Used Acronyms ACT Air Charge Temp ACV Thermactor Air Control Sensor AOD Automatic Overdrive Transmission APP Accelerator Petal Position AXOD Automatic Overdrive Transmission BAT Battery Voltage BCM Body Control Module BOO Brake On Off Switch BP Barometric Pressure Sensor BST Boost CCD Computer Controlled Dwell CCO Converter Clutch Override CDR Crankcase Depression Regulator CEL Check Engine Light CFI Central Fuel Injection CHT Cylinder Head Temperature CID Cylinder Identification Sensor CKP Crank Position Sensor CMP Cam Position Sensor CPS Crankshaft Po
16. sale and limited solely to the parts contained within the product s kit All products that are in question of Warranty must be returned shipping prepaid to the SELLER and must be accompanied by a dated proof of purchase receipt All Warranty claims are subject to approval by Edge Products Inc Under no circumstances shall the SELLER be liable for any labor charged or travel time incurred in diagnosis for defects removal or reinstallation of this product or any other contingent expenses If the BUYER sends back a failed unit that is out of warranty and chooses to buy a refurbished unit the refurbished unit will only carry a 90 day warranty If the BUYER purchases a new unit at a predetermined discounted rate it will have the standard 1 year warranty Under no circumstances will the SELLER be liable for any damage or expenses insured by reason of the use or sale of any such equipment IHE INSTALLATION OF THIS PRODUCT INDICATES THAT THE BUYER HAS READ AND UNDERSTANDS THIS AGREEMENT AND ACCEPTS ITS TERMS AND CONDITIONS IN THE EVENT THAT THE BUYER DOES NOT AGREE WITH THIS AGREEMENT THE BUYER MAY PROMPTLY RETURN THIS PRODUCT IN A NEW AND UNUSED CONDITION WITH A DATED PROOF OF PURCHASE TO THE PLACE OF PURCHASE WITHIN THIRTY 30 DAYS FROM DATE OF PURCHASE FOR A FULL REFUND IMPORTANT INFORMATION ABOUT YOUR VEHICLE S WARRANTY Many of our customers ask Will your product void my vehicle s manufacturer s warranty While the answer is stra
17. to install both the SOFTWARE and the DRIVERS that come included in the download or on the disk before you connect your device to your PC During the installation you will be prompted to install the drivers choose yes For step by step installation instructions please copy this link into your web browser http www edgeproducts com product images product update file 11 pdf Once you ve successfully installed the Fusion Software and Drivers click on the Fusion icon on your PC desktop You may be prompted for a Fusion login If you have not yet created an account click on Create a New User and you will be taken to a webpage to create your login information After entering your information a password will be sent to the email address you provide Please be sure that your email account does not block emails from edgeproducts com Upon receiving the password enter your email address and password into the login screen You ll be prompted to connect the device to launch the update After connecting the device you ll see the following screen Click yes to continue with the update Note Be sure to return your vehicle to stock before connecting the device to Fusion Note f the USB connector you received has 2 plugs it is recommended that you plug both USB connectors into the computer before connecting the device to the other end to ensure proper operation Fiiclcrn I M rec oS ur rw A amp A FRE Update Now
18. y Updates are available for this device This process can take a while During the download From our computers you wil be able to cancel but once the m update starts sending files bo your device vou wil have Eo allow bo complete That part of the process can take up to 15 minubes Would you like Eo update now 36 Evolution FORD 7 3 Liter After you ve selected yes on the previous screen the Fusion software will go through the steps in order to update the device Once it s completed you ll see the following screen Fillon e eae Li r Lo LIF 5 ur T w a RA E The next time vou connect your device bo your vehicle please allow up to 2 minutes For the device to come up Press the OK button to clase Fusion then disconnect your device Click OK and the update will be completed You ll now have the latest Firmware and Calibration on your device When your device is connected to Fusion the Device Model Level Bootloader Firmware Calibration and Serial Number are all displayed at the bottom of the screen These numbers will be useful to quickly view the state of your device and whether or not it is currently programmed to a vehicle MODEL The model number for your device LVL The currently programmed level BOOTLOADER The bootloader version currently on your device FIRMWARE The firmware version currently on your device CALIBRATION The calibration version currently on your device SERIAL NUMB
19. Do not use the Performance Tests feature to break any traffic laws Perform these tests only where they are legal and safe Another feature often only found on the Edge Product monitors 1s the ability to determine your quarter mile times as well as your 0 60 times and has a unique Christmas tree starting sequence Ford 7 3 Liter Evolution Alerts If you would like to know when a certain parameter such as transmission temperature reaches a certain value you could set an alert to that value As the preset value 1s reached the Evolution s screen will flash red and display which alert was triggered and the current value for that particular alert parameter Please note that Alerts may flash only if that parameter is being actively displayed on the Evolution monitor Records While driving the Evolution will automatically record the highest values of some parameters These records can be viewed and reset at any time Please note that some parameters may record only if that parameter 1s actively displayed on the Evolution monitor NOTE For both Alerts and Records some truck types and years may flash alert and record peak parameter values even when not displayed on the Evolution monitor Custom Options While programming your vehicle you have the option to customize your tuning You can change certain features to better suit your driving style or your vehicle setup WOT wide open throttle shifting standard shifting shift firmness
20. ER The serial number assigned to your device Possible Programming Errors Update Required Fusion is designed to help the development team at Edge Products support new vehicle calibrations When you connect your device to the vehicle the first step it takes is identifying your vehicle s stock file If the stock file isn t currently supported the device 37 Ford 7 3 Liter Evolution will display a screen alerting you that the stock file is not yet supported and prompt you to press a button touch the screen in order to read and save the stock file Once the device has saved the stock calibration it will prompt you to connect the device to Fusion Fusion will ask you if you want to upload your vehicle s stock files to our server Choosing yes will upload the files to the server and alert the development team This will help the development team at Edge Products provide support for your vehicle s calibration as quickly as possible Non Stock condition During programming the device will read the stock file on your vehicle and compare it to a corresponding stock file that has been verified by Edge Products If there is a mismatch the device will alert you and display this message Non stock condition detected This is most likely because your vehicle has been programmed with a competitive product It is recommended that you return your vehicle to a stock condition with the product that changed it Alternatively you can plug your device i
21. NOT returned it to stock your Evolution programmer will be rendered useless If this happens call our technical support at 888 360 EDGE and they can help you recover your Evolution for a small fee Follow the steps included in this manual for returning your program to stock Tow Only Program WARNING Do not exceed your vehicle s max GVWR as outlined in the vehicle s owner s manual Doing so may result in loss of vehicle control and cause bodily injury This setting 1s the lowest power setting It is designed to provide a significant increase in horsepower and torque while still being safe enough to use for towing While it isn t necessary a modified exhaust system will help improve overall performance and help reduce your EGT exhaust gas temperature levels Race Performance Program If you plan to tow with this program it 1s strongly recommended that you make appropriate modifications to your exhaust system and install an EGT exhaust gas temperature gauge to aid in the prevention of potential damage to your engine Extreme Performance Program This 1s the highest performance setting for the Evolution The fuel injection and fuel timing strategies are aggressively tuned to extract the maximum performance from your vehicle without sacrificing drivability or durability The transmission strategy 1s modified to take advantage of the increased engine performance by providing quicker firmer shifts Power Gains The following powe
22. Tech Support Tools md j T BODAS m Diagnostics o Tech Support Gg zm ars At the Tech Support Tools menu select Self Test and press ENTER The following screen appears This screen contains various tests you may run to insure that the hardware and software of the Evolution are functioning correctly You may also be asked by a tech support representative to initiate one of these tests to help isolate a problem you could possibly have 23 Ford 7 3 Liter Evolution P agen ee i Self Test LED Test Contrast Test Speaker Test 1 Temperature Test Button Test z5 gt Ae After the test is complete press MENU repeatedly to return to the Diagnostics and Main Menu Screens Performance Testing A wARNIN G Do not use the Performance Tests feature to break any traffic laws Perform these tests only where they are legal and safe 0 60 and Quarter Mile Tests The Evolution allows you to test the performance of your vehicle by timing the 0 60 and the quarter mile times It is helpful to remember these might not be results you would receive from actual races Incorrect speedometer reading and tire slippage can cause slight miscalculations in the displayed results To run these tests perform the following steps 1 Press MENU and the Main Menu screen should appear SS 7 7 f Main Menu Ca tea gals Gu Perforance
23. Then re attach the cable and start the vehicle TROUBLE CONNECTING TO THE FUSION SOFTWARE If you are having trouble connecting to the Fusion software the first thing to check 1s whether or not you have HotSync on your computer HotSync is software used to sync your PDA Palm to your computer If you do have HotSync on your computer follow these steps 1 Right click on the HotSync icon that looks like this CO 2 You will get a menu that looks like this w Local USB Lacal Serial Modern w Network Setup Custom File Link View Lag About Help Exit 3 By default the Local Serial will have a check by it uncheck Local Serial Once you have done this you will need to restart your computer If the problem persists after restarting your computer please call Edge Products Technical Support 39 Ford 7 3 Liter Evolution Warranty Information LIMITED 1 YEAR WARRANTY Edge Products LLC hereafter SELLER gives Limited Warranty as to description quality merchantability fitness for any product s purpose productiveness or any other matter of SELLER s product sold herewith The SELLER shall be in no way responsible for the product s open use and service and the BUYER hereby waives all rights other than those expressly written herein This Warranty shall not be extended or varied except by a written instrument signed by SELLER and BUYER The Warranty is Limited to one 1 year from the date of
24. alue Pressing ENTER will save the current alert value and return you to the Alerts screen If you would like to change another parameter select that parameter and repeat the steps 5 If you would like to return to the previous screen and abort the current value change press MENU 6 When alerts are On and multiple alerts are detected the Evolution will only display one For example if you exceed the set point for both MPH and RPM the first alert the Evolution detects will be the one displayed Pressing any button will temporarily disable the alert until the vehicle falls below the set point and then will automatically re enable 33 Ford 7 3 Liter Evolution Records The Evolution automatically records the highest value of some of the parameters To view these records and to reset them do the following 1 From the Main Menu select the Setup option The Setup screen appears as follows Setup Display Alerts Records Reset Evo Settings Records Select to Clear Clear All EOT 0 0 60 0 0s 14 mile 0 mph 0 0s EGT 0 3 This is where you can view all of the current recorded high values The arrow located at the bottom right corner of the screen indicates there are more parameters than the display can show Use the UP and DOWN arrow keys to scroll through the list of records If you would like to reset a single parameter select the desired parameter an
25. d press ENTER If you would like to reset all of the records select the Clear All option and press ENTER To exit out of this list press MENU Reset Evo Settings If you would like to restore the Evolution back to original factory settings follow these Steps Note This will not program the vehicle back to stock power it will only reset the Evolution display options alerts and records back to the preset defaults from Edge Products To reset power level return to Power Programming 34 Evolution FORD 7 3 Liter Enter into the Main Menu The Main Menu screen appears as follows Power Programming Diagnostics T Setup Setup Display Alerts Records Reset Evo Settings Settings have been reset If your truck was programmed to a level it STILL IS Press a Keg 5 The Evolution settings have now been reset to match the settings as originally purchased and supplied from Edge Products Press MENU to return to the Main Menu 35 Ford 7 3 Liter Evolution Fusion PC Software Internet Connection Required to Update Fusion 9 Software allows the user to update their device to the latest version of firmware and calibration files This software 1s included on the disc provided with your device It can also be downloaded for free from Edge Products web site at www edgeproducts com or the CD can be requested by calling 888 360 EDGE 3343 Note Be sure
26. e that has been modified from a stock configuration If you have used another tuner programmer on your vehicle you will need to program back to stock and remove the device before using the Edge Products Device Failure to return to stock may result in PCM failure or engine damage About the Evolution IMPORTANT Read all Safety Warranty and Installation Instructions before installing this product Read through these instructions completely so that you understand each step prior to installation Congratulations on purchasing the Evolution by Edge Products LLC the leader in truck performance and power gain technology The following manual contains information and instructions on the proper use of the Evolution Please read carefully before proceeding to program your vehicle Note At the back of this manual we have included commonly used acronyms This should help while using the Evolution Ford 7 3 Liter Evolution Stock Program The Evolution automatically makes a backup of your stock program from your PCM before writing a new program onto your PCM This assures that you will have the stock program if when you desire to reprogram your vehicle to its original stock program We strongly recommended prior to returning your vehicle to a service center or emissions check that you return your vehicle s computer to the stock program In the event that the service center re flashes your vehicle s computer a common practice and you have
27. easily updated via the internet We are constantly adding new features and improvements to our product that we know you will want to enjoy e Confirmation of Ownership provides a record in case of product loss theft or required warranty work When you call us for support our team will already have much of the information they need to help you e Improved Product Development helps us better understand you our customers and design products that meet your needs e Special Offers allows us to inform you about special offers on accessories and or new products that fit your vehicle and enhance your driving experience e AND e Extended Warranty Plan Opportunity within the first 90 days of ownership Edge offers the option to buy a 1 year warranty extension to all customers who register their product Before installing this EDGE product the Evolution unit must be updated The Fusion software required for updating your product on your computer is included in this package as a CD Follow the instructions located in the Fusion Section at the back of this Manual All Edge modules and programmers are built to operate with OEM calibrations When you take your vehicle to a service center they may by your request or otherwise update your vehicles calibrations Therefore it is important that you return your vehicle to stock before taking it in for service Edge updates its active products i e those currently being manufactured to wo
28. ightforward from a legal standpoint it s important to educate our customers and all aftermarket consumers on some industry realities and offer some common sense precautions to minimize your risk Edge is committed to providing quality products that are safe to use Our products do not cause damage to a vehicle when used as intended Please keep in mind that towing in anything higher than the towing level and hard ariving in race or extreme performance levels is not recommended Consumers of aftermarket products are protected by the Federal Magnusson Moss Warranty Act The Act states that if something breaks on your vehicle and you take it in for warranty repair the dealer must honor your warranty unless whatever modifications you have added to your vehicle actually caused the problem in question However the reality is that many dealerships have been known to void warranties on vehicles that use aftermarket products as a matter of policy This applies in particular to those aftermarket products that produce horsepower such as performance enhancement chips modified intake manifolds or aftermarket exhaust systems regardless of product brand 40 Evolution FORD 7 3 Liter You have strong legal protection as a consumer in regard to your vehicle s warranty However Edge strongly recommends you always disconnect and remove your module programmer and monitor when you take your vehicle to a dealer for warranty work In addition leaving the
29. matic Readout TAPS Throttle Angle Position Sensor TCM Transmission Control Module TFI Thick Film Ignition System TFT Transmission Fluid Temperature TGS Top Gear Switch THS Transmission Temperature Switch TPS Throttle Position Sensor TQC Torque Control TSS Turbine Shaft Speed TTS Transmission Temperature Switch VAF Vane Air Flow Sensor VAT Vane Air Temperature VCT Variable Cam Timing VSS Vehicle Speed Sensor WAC WOT A C Cut off Switch WOT Wide Open Throttle Technical Support 888 360 3343 To expedite your support call please have your Vehicle Information Part Number Serial Number and Date of Manufacture ready prior to calling Technical Support The Edge Products information is found on the label located on the bottom of the device
30. mponents or any moving parts 5 Run the cable up under the dash and secure it with the supplied Zip ties After the supplied OBDII connector cable is installed you will connect the end of the thermocouple cable to the port on the right side of the OBDII connector during the Evolution module installation 11 Ford 7 3 Liter Evolution installing the Evolution The Evolution programmer connects to the diagnostic port of your vehicle Follow these steps to install the Evolution 1 Begin by removing the access panel that 1s located just below the steering wheel figure 1 Figure 1 2 Next turn your ignition key to the OFF position Locate the black diagnostic OBDII connector Figure 2 under the dash on the bottom right corner of the access panel area As you sit in your vehicle it could be located right below your right knee Sometimes the cover to this connector will be labeled Data link Figure 2 12 Evolution FORD 7 3 Liter 3 Connect the Edge Products connector to the OBDII port and rout the cable up over the bar behind the OBDII cable Figure 5 then run the cable toward the drivers side of the dash be sure to keep it above the emergency brake release lever Figure 3 4 With the driver s side door open remove the seal trim on the left side of the dashboard Figure 4 and feed the end of the ODBII cable up behind the dash and out between the seal trim and the side panel on the dash shown i
31. n Figure 5 Route it up to the A pillar of the vehicle and replace the access panel The cable should be protruding from the dashboard up along the A pillar and be able to move freely when pulled Figure 4 Figure 5 5 Feed roughly 4 to 6 inches of cable through the dashboard Mount the Pod onto the dashboard shown in Figure 6 with the end of the cable protruding through the front of the Pod 13 Ford 7 3 Liter Evolution 6 To secure the pod locate the metal brackets and the pod in your evolution box Note that the brackets are numbered and should be placed in the appropriate numbered locations inside the pod Use the permanent double sided tape to secure the brackets to the inside of the pod be sure that the numbers match TIP Be sure to check the position of the brackets while the Pod is resting in its desired location on the dash prior to attaching them to the Pod with the double sided tape This will help you avoid repositioning the brackets after the tape has adhered 7 Clean the pod location on the dash with hot soapy water and rinse or use 70 Isopropyl alcohol Thoroughly dry the location Attach the supplied Velcro to the bottom of the mounting brackets in the pod Leave the protective backing on the bottom piece of Velcro and test fit the pod so you have an idea of where you want it Once you have determined the appropriate positioning remove the backing paper from the Velcro place the pod in it s desired location
32. nse time of around second You ll get an llegal Start message if you start before the green and you re screen will turn red You can still finish the run but the screen will let you know that you started before the green light Note Along with the best speed and time being recorded for viewing in the Records section your most recent run data will also be stored 5 After the test is complete press MENU to return to the Performance Menu The Evolution gives you even more additional features You can choose from several different parameters to monitor how these parameters are displayed set parameter alerts and view the highest value that certain parameters have reached Changing the Display View The Evolution allows you to view multiple engine parameters on the same screen To select a desired view perform the following steps 1 From the Main Menu select the Setup option The Setup screen appears as follows Display Alerts Records Reset Evo Settings Display EOD oldLELEO OG n S o c 12 Function Ear Graph Cw E 2 Function Digital 3 Function Digital 4 Function Digital 4 Adjust LCD Settings 3 Select the desired viewing option by using the UP and DOWN arrows and pressing the ENTER key on the desired display type Below are examples of the display options 26 Evolution FORD 7 3 Liter Two Function Bar Graph Display Sample 27 Ford
33. nto the internet update system and it will load the necessary files onto your device to return your vehicle to stock If you don t have the competitive product that programmed your truck connect the device to Fusion where you ll be prompted to download the correct stock files Once downloaded simply connect the device to your vehicle and the device will program the verified stock files to your vehicle Troubleshooting Tips Tip Programming your vehicle may expose existing defects in your vehicle s PCM that could disable your vehicle It is advised that you do not program your vehicle in remote locations in case of failure Tip Keep in mind that the Evolution is a high performance product and that not all vehicles deliver the exact same power output when programmed with the Evolution It is recommended that you select a program that will best fit your needs Whether towing or traveling long distances at high speeds choose your power level wisely and keep in mind the condition and tolerances of your vehicle when selecting a suitable power level e NO DISPLAY WITH KEY ON If you should get no display when turning the key on check all of your fuses and make sure your battery is fully charged Disconnect and reconnect the OBD II cable to ensure the Evolution restarts properly If the unit restarts but fails to stay on or fails to turn on when the key is on there is most likely a communications issue Contact Edge Products Technical Sup
34. o out Once the DTCs have been cleared press ENTER to return to the previous menu CAUTION f you do not address the issue that originally caused the DTC the DTC will set again and the Check Engine light will come back on If a trouble code is set repeatedly and does not clear the user must take action to define and correct the problem Failure to correct the problem could result in powertrain damage The user must become familiar with the codes and the potential problems if left uncorrected Some Codes are set as a result of using aftermarket products Some trouble codes may have safety implications Do not clear codes unless you are familiar with the code and concerns if not corrected Use only when necessary and address all trouble code warnings Tech Support Information found in this section 1s normally only accessed when instructed by an Edge support person For example Version Info displays the current Bootloader Firmware and Calibration versions installed on your Evolution Using the Fusion software see Fusion section at back of manual you will be able to access online updates to ensure your Evolution 1s always up to date Self Test Mode The evolution has the ability to run through a series of self tests to make sure that it 1s functioning correctly Self test is accessed from the Diagnostics screen by selecting Tech Support from the next menu Press ENTER to continue as instructed on the screen and then select
35. o you will only want to turn the tap until the bottom threads of the tap are slightly deeper than flush with the inside of the exhaust manifold wall Use caution not to tap too deep since this would cause the thermocouple fitting and probe to seat too deep 3 Now that the manifold has been drilled and tapped remove the fitting from the Thermocouple and install by tightening the tapered thread end into the manifold Ideally the tip of the fitting would be less than or flush with the inside of the exhaust flow path Tighten the fitting so that it is securely seated Then install the probe into the fitting and tighten the top nut of the fitting just tight enough to keep the probe firmly mounted Make sure that the probe cable is positioned to allow best path and minimal bending for cable routing to the top of the engine compartment 10 Evolution FORD 7 3 Liter 4 With the Thermocouple installed and the 4 pin connector cable routed to the top of the engine compartment locate an opening to pass the cable through the firewall Any location where cables pass through the firewall may be used There are predrilled holes located near the brake master cylinder as shown in the following picture Fold the insulation back and expose the holes and then pass the connector and cable through and into the cab compartment Be sure to use the supplied cable ties to secure any excess cable to the firewall to prevent the cable interfering with hot engine co
36. ode 12 After pressing ENTER the main display will come up ao HIN i i Note Parameters and values might vary from what is shown 13 There are five boxes that will be displaying information about your vehicle The black box in the top right corner displays which level 1s currently programmed onto your vehicle 0 Vehicle is currently at stock Vehicle has been programmed to Tow Level 1 2 Vehicle has been programmed to Race Level 2 3 Vehicle has been programmed to Extreme Level 3 The other four boxes can show up to 4 PIDs Parameter IDs of your vehicle By default they are your vehicle s RPM MPH EGT and BST actual turbo boost Optional parameters and display formats may be selected in the Changing Display section of this manual 14 From this display press MENU to select and use other features of the Evolution The display backlight dimming can also be controlled from this display by using the UP and DOWN arrow keys Power Programming Caution Vehicle manufacturers do not recommend vehicle programming in extreme temperature Please see the service manual of your vehicle to ensure that programming is being done in accordance to the original equipment manufacturers specifications 17 Ford 7 3 Liter Evolution From the main screen press MENU to enter the main menu Then select Power Programming The following screen appears l Choose a Program
37. ou can press ENTER or MENU to return to the Main Menu 18 Evolution FORD 7 3 Liter F i C5 Programming Complete PRESS CENTERS TO CONTINLE Camo Custom Options Note After creating an initial custom program you will be able to reload the options into any future programs by selecting the Load Previous Settings option From there you can modify the values more if desired When preparing to program your vehicle you will have the option to change certain parameters Choosing YES when prompted to Create a custom program will load the Custom Options menu Selecting NO will return you to the Choose a Program Menu f f i Create a custom program No Yes Cum P acl Note Custom Options are provided to allow for flexibility based on driver preferences Any option customization done by the user is not warranted by Edge Products Please use at your own discretion Caution The following options are available and when adjusting the values it is highly advised to make gradual changes as opposed to aggressive changes This will help avoid possible powertrain damage Speed Limiter The Speed Limiter restricts the top speed of the vehicle Factory speed limit values are generally based on the tolerances of the powertrain components The evolution will allow 19 Ford 7 3 Liter Evolution you to raise your speed limiter in increments of 5 mph starting a
38. particularly important things to watch for to keep your vehicle operating the way you want it to The Edge product you have bought is a high performance product As such it does present some risks of which you should be fully aware Do not use this product until you have carefully read all the following safety information and the Owner Agreement Misapplication or misuse of this product could lead to a serious or fatal accident Comply with all safety information below and in your vehicle owner s manual Follow safety installation and operating instructions in this User SAFETY GUIDELINES 1 Do not exceed legal speed limits on public roadways Use any enhanced speed capabilities of this product only in closed circuit legally sanctioned racing environments expressly for this purpose Loss of control from speeding on a public road could seriously injure you your passengers or others on the roadway 2 Select a position on the windshield or dashboard to mount the device where it will not impair your view You must be able to see the road traffic and pedestrians without interference Be sure your mounting location meets state and local laws regarding placement of devices on the windshield or dashboard 3 Do not operate the device while driving Perform all adjustments or changes while stopped Changing a setting while under way can interfere with your attention to roadway conditions 4 Stacking performance enhancing devices or other
39. port for further assistance e NO START If you experience a No Start condition after programming your PCM return to the Power Programming menu and select Return to Stock This will allow the Evolution to reprogram the PCM with the factory calibration and recover the PCM If after reprogramming you still have a No Start condition contact Edge Products Technical Support A member of our support team can further instruct you on possible recovery procedures 38 Evolution FORD 7 3 Liter THEFT LIGHT If the theft light flashes rapidly after programming and the vehicle won t start the Evolution Programmer has experienced a conflict with the Passive Anti Theft System PATS To recover from this perform the following steps 1 Turn the key on but do not attempt to start the vehicle 2 Wait for the theft light to quit flashing rapidly This should take about 1 minute after which the theft light will flash multiple times about every 3 seconds Turn the key off and remove the key from the ignition for 30 seconds 4 Insert the key and turn the ignition to the ON position and wait for the normal engine checking procedure to take place then start the vehicle The theft light should quit flashing UJ If your vehicle still won t start and the theft light 1s blinking rapidly remove the ground battery cable from both batteries if your vehicle is equipped with two for a period of ONE HOUR to allow the theft codes to clear
40. ption The following screen appears lam Can Cx Change LED Color Red 5055 Green 100 Blue 0 5 Contrast 40 i M pe 4 Select the color you would like to change 5 Depending on the color you select a screen similar to the following appears example of Red 30 Evolution FORD 7 3 Liter d 50 Press lt ENT to set value e CA 6 As you adjust the percentage shown on the screen you should notice a change in the color of the screen Once the desired color value has been reached press ENTER If you would like to return to the previous screen and abort the current color change press MENU Adjusting the Backlight Brightness When viewing engine parameters like the sample below press the UP and DOWN arrow keys to adjust the brightness of the display Each time the button is pressed the backlight will either brighten or dim by 10 of the total brightness The default setting is 100 brightness Dimming may be helpful when driving at night Adjusting the Contrast To change the contrast perform the following steps 1 From the Main Menu select the Setup option The Setup screen appears as follows Setup Display Alerts Records Reset Evo Settings 3l Ford 7 3 Liter Evolution 2 Select the Display option The following screen appears Display 2 Function Bar Graph
41. r gains are representative of an actual test vehicle These gains were measured on a Super Flow Dyno at an altitude of 4400 Ft above sea level and represent power delivered to the rear wheels of the test truck The only modification made to the test truck was the addition of the Evolution Power gains may vary somewhat on a different vehicle or in different geographic settings Evolution FORD 7 3 Liter POWER LEVEL TOTAL HP GAIN TOTAL TQ GAIN Tow Only e qwe ee WARNING Do not combine or stack chips modules to gain more horsepower The chips could be incompatible and result in powertrain failure or create dangerous conditions such as adverse running conditions high idle DTC codes etc leading to a serious or fatal accident NOTE f stacking with the Edge Juice Attitude we highly recommend only using the TOW ONLY level Features PIDs The Evolution allows the user to view up to 4 PIDs at one time PIDs identify an address in memory which contains vehicle operating information a driver may wish to monitor See the Set Up section Diagnostics The Evolution is also a powerful diagnostics tool You can view any diagnostic trouble codes DTCs your vehicle may have which in turn allows you to fix them It will also allow you to turn off that annoying Check Engine light when the problem has been addressed no more expensive trips to the dealer for a diagnostics scan 0 60 and Quarter Mile time A warn ING
42. rk effectively with updated OEM calibrations However this process can take some time as Edge is not always made aware of calibration changes made by the OEM In the case of discontinued roducts Edge cannot ensure that your unit will work effectively if you take your vehicle to a dealership and you are given by your request or otherwise a new calibration Evolution FORD 7 3 Liter Programming your vehicle may expose existing defects in your vehicle s PCM that could disable your vehicle It is advised that you do not program your vehicle in remote locations in case of vehicle failure Caution The Evolution employs carefully modified strategies that are designed to be utilized on unmodified stock vehicles only Many aftermarket components such as cold air intake CAI kits exhaust systems and throttle body spacers as well as forced induction systems turbochargers superchargers nitrous oxide etc alter the calculated airflow characteristics of the engine In addition mechanical modifications to the engine such as displacement changes camshaft modification and cylinder head modification may alter calculated airflow characteristics Using any of these modifications either alone or in any combination in conjunction with the Evolution is NOT RECOMMENDED as it may cause an excessively lean condition which could result in engine damage Edge Products will not be responsible for any damages caused by using the Evolution on a vehicl
43. sition Sensor DTC Diagnostic Trouble Codes ECA Electronic Control Assembly ECM Electronic Control Module ECT Engine Coolant Temp EDF Electric Drive Fan Relay EDIS Electronic Distributor EGO Exhaust Gas Oxygen Sensor EGR Exhaust Gas Recirculation EGRC EGR Control Solenoid EOT Engine Oil Temperature EVP EGR Position Sensor EVR EGR Valve Regulator FDM Fuel Delivery Module FPM Fuel Pump Monitor FRP Fuel Rail Pressure HEGO Heated Exhaust Gas Sensor IAT Intake Air Temperature ICM Integrated Controller Module IDM Ignition Driver Module ISC Idle Speed Control ITS Idle Tracking Switch IVS Idle Validation Switch Diesel KAM Keep Alive Memory KOEO Key On Engine Off KOER Key On Engine Running KS Knock Sensor LOAD Engine Load LOS Limited Operation Strategy LPD Line Pressure Desired LUS Lock up Solenoid MAF Mass Airflow MAFPFV Mass Airflow Sensor Voltage MAP Manifold Absolute Pressure MAT Manifold Air Temp MCU Microprocessor Control Unit MIL Malfunction Indicator Light MPH Miles Per Hour OHC Over Head Camshaft OSS Output Shaft Speed PCM Powertrain Control Module PFE Pressure Feedback EGR Sensor PIP Profile Ignition Pickup PSPS Power Steering Pressure Switch RPM Revolutions Per Minute SES Service Engine Soon SIL Shift Indicator Light SPARK Spark Advance Retard SPOUT Spark Output Signal from ECA STAR Self Test Auto
44. t 40 mph and ending at 200 mph This feature is intended for use only in a closed circuit legally sanctioned racing environment Even if racing in a legally sanctioned environment it is your responsibility to ensure your tires and other vehicle components are rated to travel at increased speeds with the speed limiter removed adjusted If you drive on public roads after removal or adjustment of the speed limiter you must still obey all driving laws including adhering to posted speed limits To drive at racing speeds on public roads seriously endangers you your passengers and others nearby Driving at high speeds with inadequate tires or other components can lead to serious or fatal injury CAUTION Removing adjusting the speed limiter for purposes inconsistent with the product s intended function violates the product s intended use and will invalidate the product s warranty Edge Products is not responsible for or liable for the consequences of improper product use Hint This value may be lowered in fleet situations or situations where young drivers are present Rev Limiter The Rev Limiter prevents the engine from over revving and causing engine damage If you set this value to 2500 you would not be able to rev the engine beyond that even with the accelerator to the floor Setting this value higher can help take advantage of the power generated at higher RPMs If you drive on public roads after adjustment of the rev limiter you
45. tor The Evolution logo will display followed by a warning and compliance directive To indicate you accept and acknowledge the warning and compliance press the ENTER button ME Dh WARNING Misuse of this device could lead to a serious accident Do not use ta break legal speed limits Press lt EMTER to continue Before installing read and comply with all information in the User Guide Press lt EMTER to accept i Wamings remaining 4 Oe MOO Oe ll 11 After pressing ENTER the following screen will be displayed Note f you are connecting the Evolution for the first time or you have recently updated you may see a screen that says UPDATING BRIDGE This screen will show while the evolution updates the OBDII bridge when it s finished it will prompt you through the rest of the screens as outlined here f i The truck s HEX file VRAA7S8 HEX Press ENTER e D This screen shows the calibration info of the truck that the Evolution is currently connected to Note f no calibration information is shown disconnect from the OBDII plug and reconnect after 5 seconds When you come to the screen again the code should be available 16 Evolution FORD 7 3 Liter Note When first programming the vehicle take a minute to write down your HEX file in the provided table below This may be useful if you ever need to contact Edge Products Technical support Truck Hex C
46. ucee cassecsceseacccesussssssescececeessiacsscieecceys 9 Installing the E vol m iiio re v Ev Sete v EU ENE 12 Power Programming cesarean tva PI vex RV Pe I et VD PAN ETHER 17 CUSTOMS DONS MC H 19 Speed bir vis Cink sini ivi an ieee tient 19 iml M 20 mine Adjustment 5 rv pr hp RI IS FOX Ee sue siete do purtesa aee eue yov aE deve TS 20 WOT Wide Open Throttle Shillllg uote ob cea eR EXE et EE pe Ee NEN EC REY EIN E PR EE E DEP eR veio 20 Standard Std SPINE soie ea ENSE TES EE EI E DEO Da ia eta id e ido 21 Nili diiit ec H 21 WOT ID 21 Idle Speed REM Pee 21 PETIT ONT EINE TT 2I Retrieving CodeS oeste n aH e ONSE En T a PO NN is 22 Clearin CodeS ER 22 Ford 7 3 Liter Evolution Tech SUDDOED oiii iiec Cia A E UP EE saa E EE assi dio Tort eb ues OE ev eese Re CE TEE 23 OIE LOSE udi 23 Perlormunce Tel DIES aseo POWRIESISIREUNETE EMIT IN EEE E SIS YUUR RU SUU E TUNER REVUE 24 0 60 and Quarter Mile Tests 441 c eee e eene eee ee rere eene eere n ette n rete n etes n eese n eese eno pee 24 CTI 26 hanems the Display VIGW 552i ie cobi d E R ea ea gu Ceu PEU Pi Do PUER PPAR ETE Ca Sd VV EGRE TI RP
47. urn to the Setup menu with your new settings saved Below is a list of the 10 PIDs you can display and description of each e RPM revolutions per minute Engine speed e MPH miles per hour Note Dash display may be 3 MPH off from the digital display due to mechanical differences in the spring etc used to control the gauge e BST Boost Pressure PSI e EGT Exhaust Gas Temp Degrees F e FOT Engine oil temperature Degrees F e TFT Transmission fluid temperature Degrees F Automatic Trans ONLY If you have a manual trans the value displayed will be incorrect Note Trans fluid Temp will not read on 1999 year models and some early model 2000 e IAT Intake air temperature Degrees F e BARO Barometric pressure PSI e BAT Battery voltage e DTC Diagnostic trouble code count 29 Ford 7 3 Liter Evolution Changing the Backlighting Adjusting the Backlight Color Contrast To change the backlighting color perform the following steps 1 From the Main Menu select the Setup option The Setup screen appears as follows e Setup Display Alerts Records Reset Evo Settings TUN 2 Select the Display option The following screen appears Display o Do Fonton E Grech Cas Pic Faction DAt P sni 3 Function Digital Ss 4 Panetion Digital o p Adjust LCD Settings E iet J 3 Select the Adjust LCD Settings o
Download Pdf Manuals
Related Search