SDMS - SenTec Digital Monitoring System
Contents
1. Clothing Clip for Sensor Cable 2 X Product Clothing Clip for Sensor Cable 2 pcs Product code SC CC Clip for fixation of the cable of SenTec sensors models VS A P VS A P N RSS M on patient clothes or bed linen The Clothing Clip secures the sensor cable on the patient s clothes or on the bed s linen Proper cable organiza tion can help to reduce strain To prevent dislocation of the sensor no strain should pull on the sensor when attached to the patient 13 30 K100816 senTec SpO2 Soft Sensor Product SpO2 Soft Sensor SpO2 and PR Product code RSS M Reusable finger tip sensor for non invasive and continuous measurement of pulse oximetry SpO2 PR suitable for patients weighing more than 20 kg The sheath like design of the rubber tube which is resilient to immersion guarantees very easy handling and cleaning The SpO2 Soft Sensor initially is available in one size RSS M me dium To be connected to the SDM with a SpO2 Adapter Cable SC XXX Requires SDM firmware version SMB V07 00 MPB V05 00 or newer Compatible with non OxiMax Nellcor Pulse Oximetry Nellcor and OxiMax are registered trademarks owned by Covidien AG SpO2 Adapter Cable Product Code Product SpO2 Adapter Cable SC 150 Length 150 cm SC 250 Length 250 cm SC 750 Length 750 cm SC YYY Customized Length up to 920 cm Adapter Cable required to connect the SpO2 Soft Sensor RSS M to the SenTec Dig2. Cables Demo Set Product code PSG Demo The PSG Adaptor Cables Demo Set is designed to efficiently demonstrate interfacing of the SenTec Digital Monitor with various polygraphs PG or polysomnographs PSG The PSG Adaptor Cables Demo Set can be used to adapt the SDM to the following PG or PSG systems EMBLA 4500 EMBLA S7000 EMBLA N7000 Titanium Embla Alice3 Alice4 Alice5 Philips Respironics SOMNOlab Weinmann Comet Gras E Series Siesta Compumedics Porti4 Porti 5 Dr Fenyves und Gut EasyScreen Heinen und Lowenstein 19 30 K100816 sSenTec PSG Adaptor Cable universal Product PSG Adaptor Cable universal Product code PSG X Adaptor Cable SDM to Polygraph or to Polysomnograph length 180 cm open wires This universal PSG Adaptor Cable can be used to interface the SDM with most Polygraphs PG or Polysomno graphs PSG Technicians simply attach the open wires to the required plugs for their particular PG or PSG Ready made cables are available upon request to connect the SDM to the most common PG or PSG systems Embla Alice Sleeplab Pro Nurse Call Cable universal Product Nurse Call Cable universal Product code NC X Adaptor Cable SDM to nurse call system length 180 cm open wires This universal Nurse Call Adaptor Cable can be used to interface the SDM with most nurse call systems Hospi tal technicians simply attach the open wires to the required p
3. N SDMS _ nG or SDMS N_nG Patient Monitoring System Patient Monitoring System comprising 1 SenTec Digital Monitor SDM with current firmware version 1 V Sign Sensor model VS A P or VS A P N 1 Digital Sensor Adaptor Cable AC 150 1 V STATS Installation CD V STATS CD 1 Starter Set see table below and 1 V Sign Training Set VS TSET 1 User Manual CD UMCD 1 Quick Reference Guide QRG xx 1 Instruction Manual IM xx and 1 main power cord are also in cluded For details on contained items see corresponding product codes Depending on the Product Code used one of the four available Starter Sets will be shipped VS SSET Standard Starter Set with 1 bottle Service Gas VS SSET N Neonatal Starter Set with 1 bottle Service Gas VS SSET_NG Standard Starter Set without Service Gas VS SSET N_nG Neonatal Starter Set without Service Gas Note SDMS and SDMS N each contain 1 bottle Service Gas a pressurized container and therefore are considered as dangerous goods when shipped Costs related to handling of dangerous goods during shipment in particular for air freight may arise Note Gas bottles are pressurized containers SDMS SDMS N and GAS 0812 therefore are considered as dangerous goods GAS 0812 contains 6 gas bottles whereas SDMS or SDMS N contain only 1 gas bottle The costs per gas bottle that are related to handling of dangerous goods
4. during shipment in par ticular for air freight therefore are higher when ordering 1 SDMS or 1 SDMS N as compared to order ing 1 SDMS_nG and 1 GAS 0812 or 1 SDMS N_nG and 1 GAS 0812 respectively 3 30 K100816 sSenTec Starter Set Ear Clip EC MI Multi Site Attachment Ring MA MI Multi Site Attachment Ring MAR SF for mature intact skin for mature intact skin for sensitive fragile skin A 7 i Contact Gel V Sign Membrane Changer VS MC Service Gas Il v i Product Starter Set Product codes VS SSET VS SSET N VS SSET_nQ or VS SSET N_nG Set of disposables covering approximately one month s need Four different Starter Get configurations are available e Standard Starter Set Neonatal Starter Set Product Code VS SSET VS SSET_nG VS SSET N VS SSET N_nG Multi Site Attachment Rings MA MI Multi Site Attachment Rings MAR SF V Sign Membrane Changer VS MC Contact Gel GEL 04 Service Gas GAS 0812 Note VS SSET and VS SSET N each contain 1 bottle Service Gas a pressurized container and therefore are considered as dangerous goods Costs related to handling of dangerous goods during shipment in particular for air freight may arise Note Gas bottles are pressurized containers VS SSET VS SSET N and GAS 0812 therefore are consid ered as dangerous goods GAS 0812 contains 6 gas bottles wh
5. economic and cost saving membrane change the V Sign Membrane Changer after use can be reloaded with a new V Sign Membrane Changer Insert VS MCI V Sign Membrane Changer Insert 5X Product V Sign Membrane Changer Insert 5 pcs Product code VS MCI Separately bagged single use Inserts for the V Sign Membrane Changer The V Sign Membrane Changer VS MC is a reloadable tool to change the membrane of V Sign Sensors models VS A P and VS A P N Prior reuse the V Sign Membrane Changer must be reloaded with a new V Sign Membrane Changer Insert 11 30 K100816 senTec V Sign Membrane Changer SET Product V Sign Membrane Changer SET 1 VS MC and 1 VS MCl Product code VS MCSET Set of 1 V Sign Membrane Changer and 1 V Sign Membrane Changer Insert Contains one loaded V Sign Membrane Changer VS MC and one V Sign Membrane Changer Insert VS MCI for a total of two membrane changes V Sign Training Set o Product V Sign Training Set Product code VS TSET Set to train the membrane change of the V Sign Sensor The V Sign Training Set is intended to teach the change of the membrane of the V Sign Sensor models VS A P and VS A P N The set contains a multiple use Membrane Changer a Dummy Sensor and 2 multiple use Membrane Rings With this set no V Sign Membrane Changers VS MC have to be spent for training pur poses 12 30 K100816 SsenTec
6. installed versions of Download 2001 can be upgraded to include the SenTec Digital Monitor SDM Updating the Download 2001 software is simply by removing the installed software and installing Visi Download The data already downloaded remains in the old data directory 17 30 K100816 SsenTec Data Management Accessories PC and Printer Interface Cables Adapters Accessories A number of accessories are available for data communication between the SDM and the PC or the SDM anda Seiko DPU 414 Thermal Printer USB232C 180 USB232 Converter Cable For data communication between the SDM and a PC with USB port e g to download data from the SDM or to configure special safety relevant settings of the SDM Specification length 180 cm DB9 Male System Requirements Pentium Class CPU with USB port PC WIN 98 2000 XP environment 1 available USB type A downstream port RS232C_MF Serial RS232 Cable DB9 Male Female For data communication between the SDM and a PC with RS232 port DB9 e g to download data from the SDM or to configure special safety relevant settings of the SDM Specification length 180 cm or 200 cm DB9 Male Female SDMPrinter_C180 Printer Cable SDM to Seiko DPU 414 Thermal Printer To interface the SDM with the Seiko DPU 414 Thermal Printer if printing of trend data is required Specification length 180 cm 18 30 K100816 sSenTec PSG Adaptor Cables Demo Set Product PSG Adaptor
7. oxygen saturation sensor Digital Sensor for non invasive and continuous measurement of transcutaneous carbon dioxide partial pressure tcPCO2 and pulse oximetry SpO2 PR Suitable for adult pediatric and neonatal patients Includes 1 SC CC With the V Sign Sensor 2 SoO2 and PR measurements are no longer restricted to the ear lobe and addition ally can be measured at the forehead and cheek of adult or pediatric patients If applied to sites other than the earlobe forehead or cheek and in particular for neonatal usage V Sign Sensor 2 is currently indicated for tcPCO2 monitoring only To be connected to the SDM with a Digital Sensor Adapter Cable AC XXX Requires SDM firmware version SMB V07 00 MPB VOD OU or newer 7 30 K100816 sSenTec Digital Sensor Adapter Cable Product Code Product Digital Sensor Adapter Cable AC 150 Length 150 cm AC 250 Length 250 cm AC 750 Length 750 cm AC YYY Customized Length up to 920 cm Adapter Cable required to connect the V Sign Sensor models VS A P and VS A P N to the SenTec Digital Monitor SDM Ear Clip for Adults Pediatrics Neonates with mature intact skin 24 x Product Ear Clip 24 pcs Product code EC MI Single patient use ear clips for use with the V Sign Sensor models VS A P and VS A P N The Ear Clip is required to attach the V Sign Sensor models VS A P and VS A P N to the patient s earlobe Suitable for adult pediatric and
8. L Clean the earlobe with sab wetted with 70 isopropanol and 4 5 GEN et it dry Insert the sensor into Ear Clip remove cover of adhesive wee gt Membrane Change the sensor membrane periodically as requested i tape and place one small drop of contact liquid on surface of pds by the montor Place Membrane Changer on a solid flat surface Hold A 5 sensor Hold sensor horizontally so the contact Squid does not rol sc the sensor head with the membrane face upwards and insert the aw Ne e off the sensor face en V Sign Sensor into the Membrane Changer Keep the Memb ane 4 KO Changer horizontal while repeating the following procedure 4 times D h 2 Pull earlobe in horizontal position From the side move the VK Ki d sensor horitontally in and attach the sensor from below to the back 4x 1 Press down slowly but firmly with the hee ofhand then side of the earlobe Close dip from above then guide earlobe back Ge yf 2 grab base of tool with one hand tum top clockwise with n vertical position ch V other hand to next stop Note Verify thet the whole dark surface of the sensor is covered Tt D At the end lift the senor to remove it from the tool and verify R by the earlobe Ensure that air gape are eliminated between the Ix thet the membrane is securely seated skin and the sensor ES 4 Confirm the membrane change on the monitor and place the 3 Wap cable around the ear once and tape the cable to the cheek L 4 sensor in the
9. SenTec A new dimension in non invasive patient monitoring PCO Spo N D Imagine the possibilities PRODUCTS 2010 Valid from August 16 2010 SsenTec Content SenTec Digital Monitoring System SDMS Starter Set SDMS Carry Bag SenTec Digital Monitor V Sign Sensor V Sign Sensor 2 Digital Sensor Adapter Cable Ear Clip Contact Gel Multi Site Attachment Ring MAR SF Multi Site Attachment Ring MAR MI service Gas V Sign Membrane Changer V Sign Membrane Changer Insert V Sign Membrane Changer SET V Sign Training Set Clothing Clip for Sensor Cable SpO2 Soft Sensor SpO2 Adapter Cable V STATS Installation CD V CareNeT Package Registration Code Visi Download Data Management Accessories PSG Adaptor Cables Demo Set PSG Adaptor Cable universal Nurse Call Cable universal Potential Equilization Cable VueLink Adaptor Roll Stand for the SenTec Digital Monitor Cable Cleat amp Bin for Disposables Mounting Plate for Infusion stands and Wall railings Mounting Plate for Wall railings Mounting Plate for Roll Stand Heads Quick Reference Guide for SDMS Instruction Manual for SDMS User Manuals CD 2 30 O 0 OO OD NNDU SS W K100816 SsenTec SenTec Digital Monitoring System SDMS 161 li AKRAAAARAS 84 51 pR NNN NNN VN NN NNN e tpm SEI Trend amp Pietysmogram w Product SenTec Digital Monitoring System Product codes SDMS SDMS
10. Station J Product V CareNeT Package Registration Code Product Code V STATS_CPRC The V CareNeT System enables remote monitoring and alarm surveillance for up to 20 SenTec Digital Moni tors SDM being connected to the same network as the PC with V CareNeT i e the PC with V CareNeT is used as a central station for patient monitoring For all admitted patients the central station displays all relevant SDM data and alarms With V CareNeT System it is furthermore possible to download trend data stored in the internal memory of the SDM via the network for subsequent display analysis and reporting in V STATS Up to 40 SDMs can be simultaneously connected to V CareNeT via the network Up to 20 patients can be simulta neously admitted for remote monitoring V STATS 3 00 incorporates the V CareNeT Package however note that the V CareNeI only can be used after activation of the V CareNeIT Package To activate the V CareNeI Package the installed V STATS license must be registered and you need to purchase a V CareNeT Package Registration Code CPRC The CPRC you subsequently need to generate the V CareNeT Package Activation Code CPAC on the website http registration sentec ch vstats CPAC html To activate the V CareNeT Package you finally must enter the CPAC within V STATS into the appropriate field of the dialog V CareNeT Package Activation 16 30 K100816 SsenTec Vis
11. docking staon A calibration wil start KA En ingers For additional information instructions refer to the Instruction Manual the Technical Manus or avanzi one in s oli Garii att to the sersor and ear dip as a final security check Secure senso the respective Directions for Use of the sensor and accessories cable with Clothing Clip on shirt or bed inen Contact liquid Contact Gel clean tap water sterile water and S 2 n i C E sterile saline solution 0120 Chi wow Seite ch WD Pei at RU y as shown in the picture Provide a smal squeeze with your V Product Quick Reference Guide for SDMS Product code QRG xx please replace xx with desired language code Hardcopy of Quick Reference Guide for SDMS Contact us for availability of languages Instruction Manual for SDMS truction Manual Far the j 5 Kid i pali Product Instruction Manual for SDMS Product code IM xx please replace xx with desired language code Hardcopy of Instruction Manual for SDMS Contact us for availability of languages 28 30 K100816 SsenTec User Manuals CD F La We e ss FA Me Fa LE d SenTec AG Ringstrasse 39 CH 4106 Therwil Switzerland www sentec ch SenTec Digital Monitoring System Manuals and Directions for Use HB 005826 k REF UMCD Product CD User Manuals Product code UMCD CD containing PDF versions of current versions of product manuals and Directions for Us
12. e Contains Quick Reference Guide and Instruction Manual for the SDMS in all supported languages Technical Manual for the SDM in English only Translation Matrix for Menu amp Status Messages of the SDM for all supported languages VueLink Installation Manual in English only Flexport Interface Manual in English only Service Manual for the SDM in English only Directions for Use for the various Disposables in English only Instruction Manual for V STATS in all supported languages V STATS Installation Manual Installation Manuals for Mounting Plate and Cable Cleat in English only Certificate for Disinfection Protocol for Safety Related Test Repair Form in English only 29 30 K100816 sSenTec Deh r gg MAAT DN Ti ANNA v NNN NINNI W D gei Trend amp Piethysmogram ra senTec SenTec AG Ringstrasse 39 CH 4106 Therwil Phone 41 61 726 97 60 Fax 41 61 726 97 61 info sentec ch www sentec ch 30 30 K100816
13. ereas VS SSET or VS SSET N con tain only 1 gas bottle The costs per gas bottle that are related to handling of dangerous goods during shipment in particular for air freight therefore are higher when ordering 1 VS SSET or 1 VS SSET N as compared to ordering 1 VS SSET_nG and 1 GAS 0812 or 1 VS SSET N_nG and 1 GAS 0812 respectively 4 30 K100816 SsenTec SDMS Carry Bag Product SDMS Carry Bag Product code SDMS_ CB Carry Bag for the SenTec Digital Monitoring System SDMS Designed specifically for the SDMS this stylish yet sturdy and durable carry bag is perfect for transporting your SDMS The bag easily accommodates the SenTec Digital Monitor SDM sensors cables Sensor adapter ca bles power cable as well as frequently used disposables Documents Quick Reference Guide Instruction Manual can be stowed in a specifically designed compartment Its zipper top can be opened for monitoring dur ing patient transport whereas its Velcro bottom can be opened to access the monitors rear panel with the ON OFF switch the AC Power Connector the sensor connection port and the different data communication ports Specifications General Zipper top Velcro bottom which can be quickly Size 340 X 285 X 150 mm pulled open Color grey Side Compartment Material hard wearing Nylon padded Meshes subdivide the side compartment in 4 Sturdy adjustable shoulder strap removab
14. gt to l j g j 1 s r zl Product Mounting Plate for Roll Stand Heads Product code MP RSH Mounting plate for fixation of SDM to heads of roll stands The mounting plate fixes the SDM to heads of roll stands such as e g GCX POLYMOUNT This mounting plate is designed such that it can be used together with the Cable Cleat see product code CC_SDM 27 30 K100816 sSenTec Quick Reference Guide for SDMS Sensor Application using a Multi Site Attachment Ring e deRemave hai if necessary Clean the skin at the measuring site swith swab wetted with 70 isopropanol for neonates may only use vater and let amp dry senTec Safest verson SMB SW 00 HRB SNE 00 2 Remove cover of adhesive tape of the attackment ring and attach tthe ring to the measuring site Press gently on snap ring Move your Routi ne Use finger around the ring circumference to ensure a good adhesion of the entre adhesive to the skin Prior to usage verify that the message Ready for Use ge A 3 r ri Bauid or dean tap water to Wenn d Gisoleyed on the monitor Check the Available monitoring 3 Apply one small drop of cortact Squid or clean tap water to Read for use time the selected Patient mode Adult Neonatal and S J the skin area in the center of the attachment ring d the temperature settings Consider the table below to 4 Holding tte sensor at the cable strain relief approach the MAR choose the desired measure
15. i Download A Gaentific Instrumen of S dig Visi Download For Microsoft 3 Windows S Win XP Vista 7 includes 30 day 12 download limited licence Stowood Copyright 2010 Stowood Scientific Instruments Ltd Tel amp Fax 44 0 1865 35 8860 Not for sales in d www stowood com o the U S A 20 gt 10 for AA i ert Product Code Product Visi Download VDCSF Visi Download multiple devices CD and license security key VDS2nd Visi Downlaod second license Security key Visi Download from Stowood Scientific Instrument Ltd is a PC based software package for downloading view ing analysis and reporting data from pulse oximeters pbCO2 ETCO2 and pO2 recorders from multiple manufac turers Visi Download also supports the SenTec Digital Monitor SDM i e it is possible to download trend data from the internal memory of the SDM to a PC Subsequent data analysis includes detection and marking of events e g desaturations hypercapnia artifacts and invalid measurement periods The data analysis criteria are user adjustable The results of the data analysis can be printed along with the graphs as configurable re ports Visi Download currently supports six languages English Francais Castellano Deutsch Italiano Neder lands and devices from multiple manufacturers BCI GE Datex Ohmeda Draeger Konica Minolta Masimo Nonin Novametrix Radiometer SenTec and Stowood Upgrading a previously installed version Previously
16. ital Monitor SDM SpO2 Adapter Cables incorporate a converter within a dedicated housing Requires SDM firmware version SMB V07 00 MPB VOD OU or newer 14 30 K100816 SsenTec V STATS Installation CD current version x A a WA Ki KH V STATS with V CareNeT Package Remote Monitoring amp Trend Data Download Analysis gt l i Software for Sen ec Digital Monitors Rinagstrass Version 3 00 for License No 20100048 Windows XP Vista Vi er I L i Product V STATS Installation CD current version Product code V STATS CD PC based Remote Monitoring amp Trend Data Download Analysis Viewing Software for SenTec Digital Monitors PC based software required a to configure special safety relevant settings of the SenTec Digital Monitor SDM b to manage SDM Parameters Settings and c to download trend data from the internal memory of the SDM to a PC It includes many useful features to analysis and view the downloaded trend data Currently sup ported languages are English German and French Starting from V STATS 3 00 the software includes the V CareNeT Package which enables remote monitor ing and alarm surveillance for multiple SDMs being connected to the same network as the PC with V STATS 15 30 K100816 V CareNeT Package Registration Code V CareNeT System Router Switch LAN Network V STATS valer Central
17. le parts to accommodate power cable and fre Main Compartment quently used disposables Accommodates monitor sensor extension Ca Documents can be stowed in a specifically de ble and gas bottle signed compartment Two gauze covered ventilation slots Zipper to open close Velcro is a registered trademark owned by Velcro Industries B V 5 30 K100816 sSenTec SenTec Digital Monitor 4 m n ANNA WAV O Sas E y zi Trend amp Plethysmogram 775 Product SenTec Digital Monitor Product code SDM Stand alone Patient Monitor with integrated calibration chamber Stand alone Monitor for display of data measured with SenTec Sensors Includes mains power cord Shipped with the current firmware version 6 30 K100816 SsenTec V Sign Sensor Product V Sign Sensor Product code VS A P Carbon dioxide tension and oxygen saturation sensor Digital Sensor for non invasive and continuous measurement of transcutaneous carbon dioxide partial pressure tcPCO2 and pulse oximetry SpO2 PR Suitable for adult pediatric and neonatal patients Includes 1 SC CC If applied to sites other than the earlobe and in particular for neonatal usage V Sign Sensor is currently indi cated for tePCO2 monitoring only To be connected to the SDM with a Digital Sensor Adapter Cable AC XXX V Sign Sensor 2 Product V Sign Sensor 2 orange cable Product code VS A P N Carbon dioxide tension and
18. liquid e g Contact Gel must be applied to the center of the sensor membrane or to the measurement site Note Instead of the Contact Gel you may also use clean tap water sterile water or sterile saline solution 0 9 sodium chloride to apply the V Sign Sensor Service Gas Product Service Gas 6 bottles Product code GAS 0812 Calibration Gas cylinder of 0 56 I 9 5 bar 5 7 at 1 bar 21 C The Service Gas is required for the calibration of the PCO part of V Sign Sensors models VS A P and VS A P N Depending on usage of the SDMS one Service Gas cylinder lasts for approx 3 to 4 weeks Note Pressurized containers are considered as dangerous goods Costs related to handling of dangerous goods during shipment in particular for air freight may arise 10 30 K100816 SsenTec V Sign Membrane Changer 9 x LA Product V Sign Membrane Changer 9 pcs Product code VS MC Reloadable tool to change the membrane of V Sign Sensors models VS A P and VS A P N The membrane and the electrolyte of V Sign Sensors models VS A P and VS A P N must be changed peri odically For this purpose the old sensor membrane must be removed the sensor surface must be cleaned new electrolyte must be applied and a new sensor membrane must be put on The patented V Sign Membrane Changer is a tool that allows the user to carry out the whole membrane change process by 4 simple press and turn steps To enable an
19. lugs for their particular nurse call system 20 30 K100816 SsenTec Potential Equilization Cable 56 ee en De a i ss E D om z ZZZ 28 ULL EY el _ d N N N ST Sas es SAS N 7 2 N Product Potential Equilization Cable Product code POT 300 Potentially compensated hospital equipment cable for Category 3 and 4 medical examination rooms TUV tested Highly flexible connecting leads with green yellow insulation for potential equalization On both ends with assem bled right angled spring loaded socket Sockets made of nickel lated brass with Multilam made of gold plated hard drawn copper alloy Specifications Length 300 cm Sleeve Insulation TPE Lead cross section 4 0mm Lead cross section 4 0mm 21 30 K100816 sSenTec VueLink Adaptor Product VueLink Adaptor Product code VL A Adaptor SDM to Philips VueLink interface module Interfacing the SDMS with Philips Patient Monitors allows Medical staff to display SDMS measurement data to gether with data collected by other devices on the main screen of the Philips Monitoring System Interfacing with Philips Patient Monitors requires an SDM with firmware version SMB V05 11 or newer The hospital technician will connect the SDM via the VueLink Adaptor to a VueLink connection cable with D SUB 9 connector and a VueLink Interface Module Auxiliary Plus T
20. ment parameter application from the flap side and first insert the nose of the sensor into the Shes and recommended sensor accessory ring Then apply a sight downward pressure on the cable strain Measurement Sites and Sensor Applications relief Twist the sensor in the ring and press the sensor gently against the skin to spread the contact liquid Ensure that air gaps Adult Pediatric Patients gt 1 month of age Neonates up to 1 month of age are eliminated between the skin and the sensor Tape the cable to the skin and secure it with Clothing Clip on shirt or bed linen For forehead cheek placement wrap the cable once around ear first Note Alternatively you may dick the sensor into the Multi Site Attachment Ring first and then attach the assembly to the skin Contact liquid Contact Gel dean tap water sterile water or sterile saline solution Patient Monitoring IMPORTANT Verify that POO2 is rising initially POO2 stabilization period and that the readings for Sp02 and PR if enebled Always clean sensor are stable IF needed reposition the sensor after use After Monitoring Always keep the monitor When monitoring is completed or Remaining Monitoring switched on and the Time has elapsed remove sensor from patient and LIE resch check the skin Clean the sensor with a swab wetted with sensor in the Docking 70 isopropanol and shways store it in docking station Station d E E Se Maintenance Intervals
21. neonatal patients with mature intact skin and earlobes of sufficient size 8 30 K100816 sSenTec Multi Site Attachment Ring MAR SF for Adults Pediatrics Neonates with sensitive fragile skin 24 x Product Multi Site Attachment Ring for Adults Pediatrics Neonates 24 pcs Product code MAR SF Single use Attachment Ring for use with the V Sign Sensor models VS A P and VS A P N MAR SF is intended to attach the V Sign Sensor models VS A P and VS A P N to various measurement sites For neonates as well as for adults and pediatrics with sensitive fragile but intact skin Multi Site Attachment Ring MAR MI for Adults Pediatrics Neonates with mature intact skin Product Multi Site Attachment Ring for Adults Pediatrics Neonates 50 pcs Product code MAR MI Single use Attachment Ring for use with the V Sign Sensor models VS A P and VS A P N MAR MI is intended to attach the V Sign Sensor models VS A P and VS A P N to various measurement sites For adults pediatrics and neonates with mature intact skin 9 30 K100816 sSenTec Contact Gel Product Contact Gel 5 ml Product code GEL 04 Contact Gel for the application of the V Sign Sensor models VS A P and VS A P N 5 ml The Contact Gel is required for proper CO gas conduction from the patient s skin to the V Sign Sensor Every time the V Sign Sensor is to be attached to the measurement site one drop of contact
22. t code RS_SDM as well as with the different mount ing plates See product codes MP WR MP RSH and MP IW To stow frequently used disposables such as the Ear Clips Multi Site Attachment Rings and Sensor Gel a Bin for Disposable CC_BFD can be optionally attached to the Cable Cleat for the SenTec Digital Monitor 24 30 K100816 senTec Mounting Plate for Infusion stands and Wall railings Product Mounting Plate for Infusion stands and Wall railings Product code MP IW Universal mounting plate for fixation of SDM to infusion stands and wall railings The universal mounting plate fixes the SDM either to infusion stands or other rigid tubes or poles with diameters from 12 mm to 38 mm or to wall railings with standard dimensions of 25 mm height and 10 mm thickness This mounting plate is designed such that it can be used together with the Cable Cleat see product code CC_SDM 25 30 K100816 sSenTec Mounting Plate for Wall railings Product Mounting Plate for Wall railings Product code MP WR Mounting plate for fixation of SDM to wall railings This mounting plate fixes the SDM to wall railings with standard dimensions of 25 mm to 35 mm height and 8 mm to 10 mm thickness This mounting plate is designed such that it can be used together with the Cable Cleat see product code CC_SDM 26 30 K100816 senTec Mounting Plate for Roll Stand Heads d D Se sl N E ze a i
23. ype B with Digital Open Interface Driver Both are available at Philips dealers only 22 30 K100816 sSenTec Roll Stand for the SenTec Digital Monitor Product Roll Stand for the SenTec Digital Monitor Product code RS_SDM Roll Stand for the SenTec Digital Monitor with basket and cable cleat The Roll Stand for the SenTec Digital Monitor provides a mobile mounting option for your monitor The stand is durable and lightweight with locking castors and a pivoting head allowing adjustment for enhanced viewing The attached basket accommodates additional supplies as well as storage for the sensor cable when not in use The Roll Stand is designed such that it can be used together with the Cable Cleat see product code CC_SDM 23 30 K100816 SsenTec Cable Cleat amp Bin for Disposables Cable Cleat CC_SDM Bin for Disposables CC_BFD SDM with SDM with Cable Cleat Cable Cleat and Bin for Disposables Product Code Product CC_SDM Cable Cleat for SenTec Digital Monitor CC_BFD Bin for Disposables to be mounted on Cable Cleat for SDM Use the Cable Cleat of the SenTec Digital Monitor CC_SDM to stow the sensor cable when not in use thereby protecting it from damage or breakage The base plate of the cable cleat has to be mounted on the bot tom of the SenTec Digital Monitor The Cable Cleat of the SenTec Digital Monitor is designed such that it can be used together with the Roll Stand for the SDM see produc
Download Pdf Manuals
Related Search