Home

ZQ110 - Zebra Technologies Corporation

image

Contents

1. 3 Slide the printer into the vehicle holder completely as shown Push in the printer until you hear a click Rev 1 00 25 Mobile Printer User Manual ZQ110 3 8 Control Panel Usage Power Button This button is used to turn the printer on and off When the printer is off pressing this button for approximately 2 seconds will turn on the power When the printer is on pressing this button for approximately 2 seconds will turn off the power Paper Feed Button To manually feed the paper press this button In addition self testing and Hexadecimal Dumping can be done OP 1 Refer to 4 Self Test for self test information 2 Refer to the service manual regarding Hexadecimal Dumping e Battery Status LED Green 1 If three green LEDs are lit the battery is fully charged 2 Ilf two green LEDs are lit the battery is half charged LI ETE 3 If one green LED is lit the battery is at the lowest charge level 4 If one green LED is blinking the battery must be charged or replaced Error LED Red Ifthe red LED is lit the media cover is open 2 Ifthe red LED is blinking either the paper is out or the print head is overheated Replace the roll of paper or turn off the printer for at least 10 minutes 3 If the red LED continues to blink it may indicate a more serious problem with the product Call your authorized service dealer Bluetooth LED Blue 1 If the blue LED
2. 0123456789 lt gt ABCD Memory S W3 Memory S W4 amp 0123456789 lt gt ABCDE 12345678 12345678 0123456789 2 Q ABCDEF on BENE ON 0123456789 lt gt ABCDEFG OFF HEHE OF SGRRR000 0123456789 lt gt ABCDEFGH 0123456789 lt gt ABCDEFGHI Memory S W5 Memory S W6 0123456789 lt gt ABCDEFGHIJ 12345678 12345678 0123456789 lt gt ABCDEFGHIJK ON BENE on B E 0123456789 lt gt ABCDEFGHIJKL OFF HEE ol E Hl 0123456789 lt gt ABCDEFGHIJKLM 0123456789 lt gt ABCDEFGHIJKLMN Memory S W7 Memory S W8 0123456789 lt gt ABCDEFGHIJKLMNO 12345678 12345678 123456789 lt gt ABCDEFGHIJKLMNOP ON Hil ON 23456789 lt gt ABCDEFGHIJKLMNOPQ OFF OFF 3456789 lt gt ABCDEFGHIJKLMNOPQR EENE alltel 456789 lt gt ABCDEFGHIJKLMNOPQRS 56789 lt gt ABCDEFGHIJKLMNOPQRST RF Interface 6789 lt gt ABCDEFGHIJKLMNOPQRSTU Not available Bluetooth 789 lt gt ABCDEFGHIJKLMNOPQRSTUV WLAN firmware version 89 lt gt ABCDEFGHIJKLMNOPQRSTUVW Ver 2 0 9 lt gt ABCDEFGHIJKLMNOPQRSTUVWX WLAN MAC address gu eifi AEae E 600 0jDUC tj cc7a30020517 ieaaa s sim AA ESE SOOOUJDUGEY Pif System Name ZQ110 saaaa sit AA Ese E ddoMUPPDUQEY Pifa Network Mode Adhoc saaa sin AE sere dd 0 0 U DUGEY Pifaic Authentication Open saa sit AA Ese E666009D c Y Ptf i i Encryption None AA E DU ESSID 125
3. Rev 1 00 31 Mobile Printer User Manual ZQ110 6 iOS MFi Mode Setting Optional This product supports Made for iOS MFi mode which enables Bluetooth communication with iOS devices How to enable and disable MFi mode Turn on the printer Open the media cover Press and hold the power button and paper feed button for more than two seconds Close the cover when you hear a beep Reboot the printer when the following message is printed jOS mode enable Please Reboot Printer 6 To disable MFi mode repeat the above procedure UI ope RE ons Check iOS mode 1 Execute a self test 2 If the printed firmware version contains a lowercase a for example V01 00 STDa iOS mode is disabled 3 If the printed firmware version contains a lowercase i for example V01 00 STDi iOS mode is enabled Rev 1 00 32 Mobile Printer User Manual ZQ110 7 Peripherals Connection This product can communicate with other devices via Bluetooth communication and cable 7 1 Bluetooth Connection 1 The printer can connect to devices equipped with Bluetooth communication capability Make sure your printer is on and discoverable 2 Use the Bluetooth connection function supported by the device to connect to the printer 1 This printer supports WLAN communication in Ad hoc mode and Infrastructure mode AP The printer can be connected to other devices such as PDAs and PC s supporting wireless LAN commun
4. zA zQ110 Mobile Printer User Manual Made for iPod LliPhone JiPad P1069083 001 Rev A Table of Contents x Manual Information amp Usage Precautions tis cede cede cedededecedeseiecedecedocedoccdecedeccdecedeeciovedeees 7 1 Gontent Confirmation ieseni ea a ea eitis rele 14 2 Product Part Namas iii is sis invasive v rte 15 3 Installation 8 Usage MENPAR RAT EATA SAS poctaensnensedubeanes ents Forts piece vals E rra A CFR E eo duro sundsvadeseasere 16 3 1 Battery Installation E NER aaa EE 1 6 3 2 Battery Charging ART TT ET 1 6 3 2 1 Battery Charging Usage i N 1 6 3 2 2 Single battery charger Optional Usage mandarin s 1 7 3 2 3 Cigarette lighter adaptor Optional Usage avesrishnise vesi ose retorika 1 7 3 2 4 Single Docking Cradle Optional Usage CUERO C I EI LL QD aa as a Z aa 1 8 3 2 5 Quad Battery Charger Quad Docking Cradle Optional Usage 7 19 3 2 5 1 Connecting the cables ta IESU M CENE SUE ERR E a METER E REDE ME E DE 1 9 3 2 5 2 Charging Battery Printer CE TEREECILEIIILCLITI a CITED 20 3 3 Paper Installation WuwawRRWERRRWERREWRREEARAWRREERRENRRRWRREERRSEREESERRREREESERRSERESERRREREMEREREREANRESHRESAERWRE RH 21 3 4 Belt Clip Usage munsnauasnuanasnasasnasasnasasnasasnansasnasasnasasnasasnasasnnsansnssnsnasassnasasnasunsnasaanasnaannan 22 3 5 Belt Strap Optional Usage dani do os 23 3 6 Protective Case Optional Usage wa R ERR M R MRNERNRMRMRRNNARREARSRMENNRRERMR ARR RN RREERRRSRRNNERAEFARREE 24 3
5. Paper 273g 0 60 Ibs Package approx 670g 1 5 Ibs Accessories Basic Package Battery Standard AC Adaptor Belt Clip Paper Power Cord Sold Separately Battery with outer contacts Protective Case Shoulder Strap Belt Strap Vehicle Holder USB Cable Cigarette Lighter Adaptor Quad Docking Cradle Quad Battery Charger Single battery Charger Single Docking Cradle Adaptor for Quad Battery Charger Docking Cradle NOTE Printer specifications are subject to change without notice Rev 1 00 35 Mobile Printer User Manual ZQ110 9 2 Certification 1 WEEE Waste Electrical and Electric Equipment This mark shown on the product or its literature indicates that the W corresponding item should not be discarded at the end of its working life with other household waste To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate marked items from other types of waste and recycle them responsibly to promote the sustained reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details on where and how they can conduct environmentally safe recycling of such items Commercial users should contact their suppliers and check the terms and conditions of purchase contracts This product should not be combined with other commercial waste for disposal 2
6. 7 Vehicle holder Optional Usage RASORE 25 3 8 Control Panel Usage Dene shiu alas sasi nn nn 26 3 9 MSR Usage munsnuanuasnanasnanasnasasnasasnanasnanasnnsnsnanasnasnsnasasunnunsnasasnasnsnasassnasasnusnanasasanananannan 27 Ae Self Tessin E cen Pt 28 5 Black Mark Paper Printing aaa anasu CRM a wan eiae wa rre d we ene ee ce D sca ro nae ea ne 31 5 1 Black mark Function Setting iasessatasasrsussasananapsaesosesaassapussarsnrsusRsussasa ERR RRERRRR RE RS 31 5 2 Auto Calibration Function WE NR ERRARE aa aa aZ ae nani ee RERBA MEUSE NE NENARMRE RENE RKAE SENERE NE SENSE ES SES 31 6 iOS MFi Mode Setting Optional Tee 32 T Peripherals GonnectlOn eire re eerie 33 7 1 Bluetooth Connection munusnanasnasasnanasnanasnasasnanasnanasnanasnanasnanasnanasnnnas nnansnasasnnanananasannan 33 7 2 Wireless LAN AA TT TT TT TT 33 7 3 Interface Cable Connection Peer Gw wis a s SEES ERE SEE ETERN ESS aaa ENE SE SE EET saw wis Ria a a tense PEDE ED 33 8 Printer Cleaning TCR 34 9 Appendix sin sd dk bunar p d dd dd Ded s see wees add id den od n der ate ie 35 9 1 Specifications PART TT TET TT TT ET 35 9 2 Gertification sasaasanaananasuanaauanaaanaasanaauanaasanaauanaasanaauanaauanaauanaasanaauanaaanaauanaananaauanaananan 36 9 3 Label Types asaasanasaanasaanasaARRARARRARARRARARRARARRARARRARARRARARRARARRARASRARARRARARRARARRARARRARARRARARRARAREA 38 Rev 1 00 2 Mobile Printer User Manual ZQ110 ll Proprietary Statements This manual contain
7. DHCP Disabled IP 192 168 1 1 Netmask 255 255 255 0 Gateway 192 168 1 2 Port 9100 HTTPS Disabled Telnet Disabled FTP Disabled SNMP Disabled Completed Rev 1 00 90 Mobile Printer User Manual ZQ110 5 Black Mark Paper Printing 5 1 Black mark Function Setting Black mark paper available at the Black mark mode Setting Operations 1 Turn on the printer power 2 Open the paper cover and press and hold down the paper feed button for longer than two seconds 3 After the buzzer tone is emitted insert paper and close the cover 4 Repeat the steps above to return to receipt mode Setting Via Memory Switch Please refer to the black mark mode switching section of the Unified Utility tool 5 2 Auto Calibration Function The Black mark paper printing function requires the recognition of Black mark paper s black bar in order to print If black mark paper s black bar are not properly recognized use the auto calibration function Auto Calibration Instructions 1 Turn the printer power off while in black mark print mode 2 Press and hold down the paper feed button and then press the power button 3 After the following printout is outputted press the power button to perform auto calibration Select the mode Auto Calibration Power Button Self Test Feed Button 4 Printer feeds three pages of Black mark paper when performing auto calibration
8. is lit Bluetooth is connected 2 If the blue LED is blinking rapidly data is transmitting between 3 the printer and another device Rev 1 00 26 Mobile Printer User Manual ZQ110 WIFI Green Yellow or Red 1 Infrastructure mode a If the LED is off the radio has not been found b If the LED is blinking red signal association If the LED is blinking yellow authenticated If the LED is solid green strong signal If the LED is blinking green weak signal f If the LED is solid red WLAN Fault authentication error 2 Adhoc 1 WiFi Direct mode e Regardless of signal power green LED is always blinking off oa Power Save Mode White During Power Save mode the white LED slowly alternates between E bright and dim The other LEDs are off 3 9 MSR Usage 1 Insert the card as shown and swipe in either direction see the arrovv NOTE If the card does not register insert the card and svvipe it again Rev 1 00 27 Mobile Printer User Manual ZQ110 4 Self Test Detailed setting of printer is able to be checked by performing self test Self Test Instructions 1 Turn off the printer power and close the media cover 2 Press and hold the paper feed button and power button simultaneously to turn on the printer 3 After printing begins release the two buttons 4 To view a printout of the ASCII pattern press the paper feed button once more 5 After the ASCII pattern is printed out t
9. not subject the battery to strong shock 8 Do not pierce the battery with a sharp object or hit it with a heavy object Avoid accidental short circuiting of any battery Allowing battery terminals to contact conductive material will create a short circuit may cause burns and other injuries or could start a fire 9 Do not solder the battery 10 Do not disassemble and or modify the battery 11 Do not charge near a source of heat or in direct sunlight 12 Do not expose the battery to high temperatures over C and do not use or store it in a hot or humid place 13 Do not use the battery if it is damaged or if the exterior is deformed in any way Rev 1 00 10 Mobile Printer User Manual ZQ110 Warning 1 Do not place the battery within the reach of small children to prevent swallowing If a child swallows the battery consult a physician immediately Do not place the battery in a microwave oven and or high voltage appliance Do not combine and use any battery of different capacity and or type with the primary battery If during battery usage storage or charging a strange odor or conditions differing from normal operations such as condensation color changes warping and so forth are detected remove the battery from the product or charger and discontinue use If the battery is not charged after the recommended charging time discontinue charging If the battery is leaking electrolytic solution a
10. This equipment is for indoor use and all of the communication wiring is limited to the inside of the building 3 The switch is the disconnecting device Turn off switch from any hazard 4 The following Bluetooth mark D022644 is only applicable to models with the Bluetooth SIG qualification 5 Instructions for the correct selection of a suitable Listed Class 2 Power Battery Charger Adaptor including This product is intended to be supplied by a Listed Battery Charger Adaptor marked Class 2 and rated output 8 4 V DC 0 8 A Bluetooth Rev 1 00 36 Mobile Printer User Manual ZQ110 A Warning Lithium lon Battery pack lt Warning gt The battery has the potential risk of overheating fire and or explosion To avoid such risks observe the following instructions e A visibly swollen battery may be dangerous Contact Zebra or your local dealer e Only use a Zebra ZQ110 charger e Keep away from open flames Do not place in a microwave e Ensure proper ventilation around all sides of the battery pack during use and storage e Do not allow the battery port to touch metal items such as a necklace coin key or clock Use only a lithium battery guaranteed by mobile phone manufacturer or Zebra Do not disassemble compress or pierce the battery pack Do not drop the battery pack from a high place or subject it to strong shock Do not expose the battery to high temperatures over 60 C Do not expose to high
11. and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment to an outlet different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help 9 3 Label Types The label types used with this printer are as follows e Rating Labels PET Other Labels PP PET Rev 1 00 98 Mobile Printer User Manual
12. attery into the slot until you hear it snap in place NOTE Since the battery is partially charged at the time of purchase charge the battery prior to product use Use the AC adaptor or the optional Single battery charger Quad battery charger 3 2 Battery Charging 3 2 1 Battery Charging Usage 1 Turn off the printer power 2 Connect the power cord to the AC adaptor 3 Open the Interface Cap G 4 Connect the AC adaptor Q to the power connector of the printer 5 Plug the power cord into an electrical outlet amp CAUTION The printer may incur serious damage if the AC adaptor provided by Zebra is not used Zebra is not legally liable for any such damages The voltage and electrical current specifications of the printer and AC adaptor must match dh WARNING Turn off the power before charging the battery for the printer Rev 1 00 16 Mobile Printer User Manual ZQ110 3 2 2 Single battery charger Optional Usage Connect the power cord to the AC adaptor 2 Connect the AC adaptor Q to the power connector on the bottom of the single battery charger G Plug the power cord into an electrical outlet Insert the battery into the single battery charger 3 until it snaps in place Turn off the printer power Connect the Cigarette lighter adaptor CD to your car s cigarette lighter jack Open the external interface cap Connect the Cigarette lighter a
13. daptor D to the power connector dh CAUTION The printer may be seriously damaged if a cigarette lighter adaptor not provided by Zebra is used Zebra is not liable for such damage WARNING Turn off the power before charging the battery for the printer Rev 1 00 17 Mobile Printer User Manual ZQ110 3 2 4 Single Docking Cradle Optional Usage 1 Turn off the printer 2 Slide the printer into the single docking cradle as shown 3 Push the printer in until you hear a click 4 Charging will begin when the printer is installed 5 Pull out the printer to remove it AA CAUTION Please be sure to use the battery with Outer contacts Rev 1 00 18 Mobile Printer User Manual ZQ110 3 2 5 Quad Battery Charger Quad Docking Cradle Optional Usage 3 2 5 1 Connecting the cables Connect the power cord to the adaptor and connect the adaptor to the power connector on the bottom of the Quad Battery Charger Quad Docking Cradle Plug the power cord into a power outlet Input power is 100 240VAC 50 60Hz 1 0A When the power is on the amber green and red LEDs are lit for three seconds WARNING ie Use only the designated AC DC adaptor 12VDC 3A f Rev 1 00 19 Mobile Printer User Manual 3 2 5 2 Charging Battery Printer NOTE ZQ110 Using the battery hooks insert the batteries into the Quad Battery Charger as shown Push the battery in until y
14. egion of the printhead with your hand while cleaning it e The printhead may be damaged by static electricity e Avoid scratching the printhead e Clean the printhead periodically if linerless paper is used Recommended cleaning period is after consuming twenty rolls of linerless paper 100 meters or approximately once a week Print quality may be degraded or printhead life may be shortened if it is not cleaned periodically Warning e Use only linerless paper that is provided by Zebra Use of other paper voids product warranty e Use a Zebra Cleaning Pen part number 105950 035 12 pack Rev 1 00 94 Mobile Printer User Manual 9 Appendix 9 1 Specifications ZQ110 Item Description Printing Method Thermal printing Print Speed 90 mm sec Receipt Paper 60 mm sec Linerless Paper Resolution 203 DPI Pap a Ry Easy paper loading Character Size Font A 12 x 24 FontB 9x17 Font C 9 x24 Characters Per ina Font A 32 Font B C 42 English 95 Character Set Expanded Graphics 128 x 33 pages International 32 Printing 1 Dimension UPC A UPC E Code 39 Code 93 Code 128 Barcode f f EAN 8 EAN 13 ITF Codabar 2 Dimension PDF417 DATAMATRIX QR Code GS1 DataBar Aztec optional Diver Windows XP 32 64bit WEPOS 2003 Server 32 64bit f VISTA 32 64bit 2008 Server 32 64bit 7 32 64bit 8 32 64bit SDK Window
15. ell as for emergency measures that may be required when using the ZQ110 printer x For additional information on the ZQ110 please refer to the following supplemental manuals 1 Windows CE Module Program Manual This manual provides information on the dll files required for Windows CE application program development 2 Windows Driver Manual This manual provides information on installation and main functions of the Windows driver for this product 3 Unified Utility Manual This manual provides information on the software used to select functions of this product modify operation conditions and so forth e VMSM Virtual Memory Switch Manager Provides information on setting the basic operation conditions of the product the use of non hardware controls and software based virtual switches NV Image Download Manager Provides information on downloading image files such as logos intended for repetitive printing Firmware Download Manager Provides information on downloading and installing the latest firmware 4 Bluetooth Connection Manual This manual provides information on the connection of this product with devices equipped with Bluetooth functionality Android iOS smart phone 5 Commands Manual This manual provides information on the protocol and functions of the control commands that can be used with this product 6 Code Pages Manual This manual provides information on each character code page that can be used with t
16. he self test is automatically terminated Rev 1 00 28 Mobile Printer User Manual Self Test Printout Sample For Bluetooth Firmware version V01 00 STDa 010114 Butter Capacity 64K Bytes Print Density 100 Default Codepage PC437 Print Speed Max 90mm s Double byte character mode Off Font 12 x 24 Paper out Bell Off Low Battery Buzzer On Power off time 15 Min Idle mode time 10 Sec MSR data including sentinel Character mode None MSR read mode Auto TRACK 1 2 3 BATT NTC OK Memory switch setup status Memory S W1 Memory S W2 12345678 12345678 ON i E ON orr HE NN NN OFRENE Memory S W3 Memory S W4 12345678 12345678 ON BEN ON orr BEER OFF BREE Memory S W5 Memory S W6 HER o8 B N FF EENE org E SHEE Memory S W7 Memory S W8 12345678 12345678 ON rT TI ON Orr RE E o cEEEEEENE RF Interface Bluetooth Firmware version 1 0 1 Bluetooth BD addre 74F07D205A9 Auth amp Encry are enable Connection Mode 2 Not available WLAN Rev 1 00 29 ZQ110 If If you want to continue LF TEST printi ng Please press FEED button ASCII 1 8 amp 0123456789 lt gt 8 amp 0123456789 lt gt A nus 0123456789 9 AB 9 8 amp 0123456789 9 ABC 6 amp 0123456789 G ABCD amp 0123456789 lt gt ABCDE 0123456789 lt gt ABCDEF 0123456789
17. his product Rev 1 00 7 Mobile Printer User Manual ZQ110 lll Safety Precautions When using the ZQ110 printer please follow the recommended safety regulations provided below Warning Violating the following instructions may cause serious injury 1 Do not plug several products into one multi outlet this can provoke over heating and a ON plug is wet or dirty wipe it before usage f the plug does not fit perfectly in the outlet do not force it Be sure to use only standard multi plug outlets 2 You must use only the supplied adaptor It is dangerous to use other adaptors 3 Do not pull the cable to unplug This can damage the cable resulting in a fire or a breakdown of the printer 4 Keep the plastic bag used to package the printer out of children s reach 5 Do not plug in or unplug with wet hands 6 Do not bend the cable by force or leave it under any heavy object Adamaged cable may cause a fire Rev 1 00 8 Mobile Printer User Manual ZQ110 Caution Violating the following instructions may cause injury to the user or damage the printer 1 If you observe smoke odor or noise from the printer unplug it before taking the following measures Turn off the printer and unplug the unit from the electrical outlet Contact an authorized Zebra Technologies service provider for repair 2 Keep the packet of desiccant material silica gel used in the packaging of the printer out of chi
18. humidity Rev 1 00 97 Mobile Printer User Manual ZQ110 Disposal Directions e Do not dispose of used battery packs carelessly e Do not burn or throw in a fire to dispose of the battery pack There is a risk of fire and or explosion e Dispose of battery packs according to the methods defined by your country or region Recommendation for Charging e Charge your battery pack according to the instruction manual to avoid risks of fire or explosion FCC compliance Information This device complies with Part 15 FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Information to the User NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and may radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off
19. ication in Ad Hoc mode and AP in Infrastructure mode NOTE Refer to the Bluetooth WLAN Manual for more specific information about 1 Open the Interface Cap 2 Connect the USB interface cable optional to the cable connector of the printer NOTE Use only the USB cables optional provided by Zebra 2 3 Connect the interface cable to the f USB port of the device PDAs PCs etc NOTE The interface cable that can be connected with the printer is available in USB type Rev 1 00 33 Mobile Printer User Manual ZQ110 8 Printer Cleaning If the interior of the printer is dusty print quality can decline In such a case follow the instructions below to clean the printer O SS E A Head B Sensor 1 Open the media cover and remove the paper if present 2 Clean the printhead A using a Zebra cleaning pen Apply the cleaning pen from the center to the edge of the printhead A for cleaning 3 Using the cleaning pen remove the paper dust from the paper detection sensor B 4 Do not use the printer for one to two minutes after cleaning the printhead A until the cleaning agent from the cleaning pen has completely evaporated and dried 5 Insert the paper and close the media cover A Caution e Make sure the printer power is turned off before cleaning e Wait for two to three minutes after power off before printhead cleaning because it may be very hot e Do not to touch the heating r
20. iver Connect the equipment to an outlet or circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help WARNING Exposure to Radio Frequency radiation To conform to FCC RF exposure re quirements this device shall be used in accordance with the operating conditions and in structions listed in this manual NOTE This unit was tested with shielded cables on the peripheral devices Shielded cables must be used with the unit to ensure compliance Changes or modifications to this unit not expressly approved by Zebra Technologies Corporation could void the user s authority to operate this equipment Rev 1 00 3 Mobile Printer User Manual ZQ110 Canadian Compliance Statement This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada IC before the equipment certification number signifies that the Industry Canada technical specifications were met It does not guarantee that the certified product will operate to the user s satisfaction Liability Disclaimer Inasmuch as every effort has been made to supply accurate information in this manual Zebra Technologies Corporation is not liable for any erroneous information or omissions Zebra Technologies Corporation reserves the right to correct any such errors and disclaims liability resulting therefrom No Liability for Consequen
21. l rights reserved worldwide Monotype Intellifont amp and UFST are trademarks of Monotype Imaging Inc registered in the United States Patent and Trademark Office and may be registered in certain jurisdictions Andy CG Palacio CG Century Schoolbook CG Triumvirate CG Times Monotype Kai Monotype Mincho and Monotype Sung are trademarks of Monotype Imaging Inc and may be registered in some jurisdictions HY Gothic Hangul is a trademark of Hanyang Systems Inc Angsana is a trademark of Unity Progress Company UPC Limited Andale Arial Book Antiqua Corsiva Gill Sans Sorts and Times New Roman are trademarks of The Monotype Corporation registered in the United States Patent and Trademark Office and may be registered in certain jurisdictions Century Gothic Bookman Old Style and Century Schoolbook are trademarks of The Monotype Corporation and may be registered in certain jurisdictions HGPGothicB is a trademark of the Ricoh company Ltd and may be registered in some jurisdictions Univers is a trademark of Heidelberger Druckmaschinen AG which may be registered in certain jurisdictions exclusively licensed through Linotype Library GmbH a wholly owned subsidiary of Heidelberger Druckmaschinen AG Futura is a trademark of Bauer Types SA registered in the United States Patent and Trademark Office and may be registered in some jurisdictions TrueType is a trademark of A
22. ldren s reach 3 Use only approved accessories for your printer do not disassemble or attempt to repair the printer yourself Contact your authorized service provider for all service replacements Do not touch the blade of the paper tear bar 4 Keep liquids and foreign objects away from the printer e If any object or liquid falls into the printer immediately unplug the printer and have it checked by an authorized Zebra Technologies service provider Rev 1 00 9 Mobile Printer User Manual ZQ110 ll Battery Safety Precautions Make sure you review the user manual carefully prior to product use To avoid risks of battery overheating combustion and explosion damage and or decline in performance and product life handle batteries carefully and comply with the guidelines below Danger 1 Do notallow liquids to enter or leak into the battery compartment 2 Do not use or leave the battery in a location exposed to high temperatures 3 When charging the battery use the exclusive charger or follow the charging requirements outlined by Zebra 4 The battery has clearly delineated positive and negative poles When inserting the battery into the charger and or product ensure that the battery is properly aligned 5 Do not heat the battery or place it in a fire 6 Do not allow the battery s positive and negative poles to contact any metals In addition do not carry or store the battery with metal items 7 Do
23. lt gt ABCDEFG 0123456789 lt gt ABCDEFGH 0123456789 lt gt ABCDEFGHI 0123456789 lt gt ABCDEFGHIJ 0123456789 lt gt ABCDEFGHIJK 0123456789 lt gt ABCDEFGHIJKL 0123456789 lt gt ABCDEFGHIJKLM 0123456789 lt gt ABCDEFGHIJKLMN 0123456789 lt gt ABCDEFGHIJKLMNO 123456789 lt gt ABCDEFGHIJKLMNOP 23456789 lt gt ABCDEFGHIJKLMNOPQ 3456789 lt gt ABCDEFGHIJKLMNOPQR 456789 lt gt ABCDEFGHIJKLMNOPQRS 56789 lt gt ABCDEFGHIJKLMNOPQRST 6789 lt gt ABCDEFGHIJKLMNOPQRSTU 789 lt gt ABCDEFGHIJKLMNOPQRSTUV 89 lt gt ABCDEFGHIJKLMNOPQRSTUVW 9 lt gt ABCDEFGHIJKLMNOPQRSTUVWX _PC437 Completed Mobile Printer User Manual ZQ110 Self Test Printout Sample For Wireless LAN Firmware version V01 00 STDa 010114 Butter Capacity 64K Bytes Print Density 10096 Default Codepage PC437 Print Speed Max 90mm s Double byte character mode Off Font 12 x 24 Paper out Bell Off Low Battery Buzzer On Power off time 15 Min BATT NTC OK lf you want to continue SELF TEST printing Please press FEED button Memory switch setup status ASCII Memory S W1 Memory S W2 1 amp 0123456789 lt gt 12345678 12345678 amp 0123456789 lt gt 7 A ON E ON amp 0123456789 lt gt AB OFF BE GH NN OP amp 0123456789 lt gt ABC amp
24. nd the solution enters the eyes immediately rinse the eye with clean water and consult a physician Neglecting to do so may cause permanent eye injuries Rev 1 00 11 Mobile Printer User Manual ZQ110 Caution D N eo Do not use or leave the battery in a location exposed to high temperatures or intense direct sunlight Do not use the battery in a location that is prone to static electricity above the recommended levels in the manufacturer s product warranty The temperature ranges for battery usage are as follows Any usage outside of these ranges may result in the battery overheating damage and performance and product life may be reduced a Charging 0 40 C b Product Usage 20 60 C c Storage 20 60 C 30 days d Long Term Storage 20 40 C 90 days Please review the ZQ110 Quad Battery Charger Installation Guide carefully for charging instructions If upon first use a strange odor overheating and or anything deemed out of the ordinary is detected discontinue use and contact an authorized Zebra Technologies service provider Store the battery in a location that is out of the reach of small children During usage make sure to place the charger and or product out of the reach of small children If the battery is leaking and the solution comes into contact with the skin or clothing immediately rinse the affected area with clean water Carefully review the user manual and precauti
25. ons prior to use When replacing the battery in the printer use a battery equivalent to the one originally installed by the manufacturer Dispose of used batteries per the instructions provided by the manufacturer Rev 1 00 12 Mobile Printer User Manual ZQ110 amp Recommended Review the user manual for instructions regarding insertion and removal of the battery from the printer The battery ships partially charged You must charge the battery fully before using the printer for the first time To charge the battery use the exclusive charger provided with your printer To avoid improper use of the battery review the product user manual carefully Do not charge the battery beyond the normal charging time indicated in the user manual If you do not plan to use the battery for an extended period of time remove the battery from the printer and store in a low humidity location If you opt to store the printer with the battery installed avoid high humidity locations High humidity may cause oxidation and a decline in printer performance Ensure that you turn off the printer after usage at the end of a work shift Neglecting to do so may cause a decline in printer performance A battery that has not been used over a long period of time may not be sufficiently charged If you opt to store the battery for future use ensure that you charge the battery to the status recommended by the manufacturer every six m
26. onths Neglecting to do so can cause a decline in battery performance and product life If the battery terminal is dirty use a dry cloth to clean prior to use Neglecting to do so may cause power stoppages or difficulty in charging the printer Each battery has a product life If the usage time of the product has become short replace the battery Wrap the terminals of used batteries with tape to insulate prior to disposal Rev 1 00 13 Mobile Printer User Manual ZQ110 1 Content Confirmation If any item is damaged and or missing contact your dealer Battery Standard AC Adaptor Paper Power Cord Belt Clip CD Registration Card xX Optional items BS 2 Vehicle Holder Belt Strap i Cigarette USB Cable Battery with outer lighter contacts Adaptor for Cradle Protective Case Single Docking Single Battery Cradle Charger Adaptor for Quad Battery Quad Battery Charger Charger Docking Cradle Rev 1 00 14 Mobile Printer User Manual ZQ110 2 Product Part Names Front Media Cover X LA Power Button Z s Open Button Paper Feed Button MSR Slot Rear Hole for Mounting Belt Strap Belt Strap Battery Interface Cap Cable Connection Power Connection Rev 1 00 15 Mobile Printer User Manual ZQ110 3 Installation amp Usage 3 1 Battery Installation 1 Insert the battery in the bottom of the printer and ensure that you align the battery hook properly 2 Push the b
27. ou hear a snap Charging begins as soon as the battery is completely inserted Batteries are charged to 8 4VDC 0 8A Lift the hook and pull up to remove the battery Turn off the printer Slide the printer into the Quad Docking Cradle as shown Push in the printer until you hear a click Charging will begin once the printer is installed When charging is complete pull out the printer to remove it amp CAUTION Please be sure to use the battery with Outer contacts Battery charging status descriptions are as follows LED Charge Status Charge Time Amber LED On Charging Green LED On Fully Charged 2 5 hours p Error POU LEN Cima Replace or Reinstall Battery Ah CAUTION 1 Ifthe red LED on the charger blinks reinstall the battery 2 Ifthe red LED continues to blink despite several attempts 4 5 times to install the battery contact your local dealer 3 The charging time may vary depending on the type of the charger and the ambient temperature Rev 1 00 20 Mobile Printer User Manual ZQ110 3 3 Paper Installation 1 Press the Open button to open the media cover 2 Insert the paper as shown Remove the empty core 3 Align the paper as shown 4 Pull out the paper as shown and close the media cover 5 Tear off any excess paper toward the side of the printer Rev 1 00 21 Mobile Printer User Manual ZQ110 3 4 Belt Clip Usage 1 Inser
28. pple Computer Inc registered in the United States Patent and Trademark Office and may be registered in certain jurisdictions All other product names are the property of their respective owners All other brand names product names or trademarks belong to their respective holders 2014 ZIH Corp Rev 1 00 5 Mobile Printer User Manual ZQ110 B Introduction to the ZQ110 This user manual gives you the information you will need to operate the ZQ110 series printer For a list of supplemental manuals provided with the ZQ110 please refer to the Manual Information section Unpacking and Inspection Inspect the printer for possible shipping damage Check all exterior surfaces for damage Open the media cover refer to Loading the Media in the Getting Ready to Print section and inspect the media compartment for damage In case shipping is required save the carton and all packing material Reporting Damage If you discover shipping damage Immediately notify and file a damage report with the shipping company Zebra Technologies Corporation is not responsible for any damage incurred during shipment of the printer and will not cover the repair of this damage under its warranty policy Keep the carton and all packing material for inspection Notify your authorized Zebra re seller Rev 1 00 6 Mobile Printer User Manual ZQ110 B Manual Information This user s manual contains basic information for product usage as w
29. s XP WEPOS 2003 Server VISTA 2008 Server 7 8 CE 3 0 and later Sensor Paper End Media Cover Open Cutter Type Tear Bar Language User language supported Paper Shape Receipt Linerless Paper Type Thermal Paper Thermal Paper Paper cot Paper Rll Max 630 mm 1 18 in Max 630 mm 1 18 in Width 57 5 0 5 mm 2 26 0 2 in 57 5 0 5 mm 2 26 0 2 in i 0 06 0 1 mm 0 08 0 008 mm td 0 0024 in 0 0040 in 0 0031in 0 0003 in Reliability Printer 50 km Receipt Paper 10 km Linerless Paper Battery Rechargeable up to 500 times USB Bluetooth Class2 V3 0 EDR ger Wireless LAN 802 11 b g n Communications Interface Communication is enabled only for devices with Bluetooth or Wireless LAN function Input Voltage 100 250 VAC Current 0 5A Max at 110VA Voltage 8 4 VDC Current 0 8A AC Adaptor Output Charging current and charging time may depend on the type option of charger Type Lithium ion Battery Output Voltage 7 4 VDC Available 8 4 6 8VDC Capacity 1200 mAh Charging Time 2 5 hours Printer 15 50 C 5 122 F Temperature Battery 0 40 C 32 104 F Usage Battery discharge 20 60 C 4 140 F Conditions Printer 10 80 RH No condensation Humidity Battery 20 70 RH Non condensing refer to the temperature conditions on page 8 Dimensions Printer 80 1mm x 118 8mm x 37 7mm 3 15 in x 4 68 in x 1 48 in Printer 190g 0 42 lbs Printer Battery 242g 0 53 Ibs Weight Printer Printer Battery
30. s proprietary information for Zebra Technologies Corporation It is intended solely for the information and use of parties operating and maintaining the equip ment described herein Such proprietary information may not be used reproduced or dis closed to any other parties for any other purpose without the expressed written permission of Zebra Technologies Corporation Product Improvements Since continuous product improvement is a policy of Zebra Technologies Corporation all specifications and signs are subject to change without notice FCC Compliance Statement NOTE This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equip ment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference with radio communications However there is no guarantee that interference will not occur ina particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the rece
31. t the belt clip screw into the belt clip mounting hole Belt Clip 2 Tighten the screw of the belt clip with an object like a coin as shown Be careful to tighten the screw in the correct direction 3 Slide the clip over the belt Rev 1 00 22 Mobile Printer User Manual ZQ110 3 5 Belt Strap Optional Usage Belt Strap 1 Insert the belt strap screw into the belt strap hole 2 Use a coin to tighten the belt strap screw as shown 3 Unfasten the belt strap Velcro 4 Slide the belt strap over a belt 5 Fasten the Velcro as shown Rev 1 00 23 Mobile Printer User Manual 3 6 Protective Case Optional Usage Gj Gy HA NOD SM ERY Rev 1 00 ZQ110 1 Open the top cover of the protective case 2 Insert your printer into the protective case as shown 3 Close the top cover 4 Using the clip on the back of the protective case attach it to the belt 5 When using the printer open the paper discharger as shown Note The clip of the protective case can be rotated 30 for each of two steps for up to 60 24 Mobile Printer User Manual 3 7 Vehicle holder Optional Usage 1 Attach the vehicle holder to the mount 2 Adjust the vehicle mount properly place the suction plate close to the glass and push the lever to fix the position Use the disk pad to mount it on the dashboard
32. tial Damage In no event shall Zebra Technologies Corporation or anyone else involved in the creation production or delivery of the accompanying product including hardware and software be liable for any damages whatsoever including without limitation damages for loss of business profits business interruption loss of business information or other pecuniary loss arising out of the use of or the results of use of or inability to use such product even if Zebra Technologies Corporation has been advised of the possibility of such damages Because some states do not allow the exclusion of liability for consequential or incidental damages the above limitation may not apply to you Rev 1 00 4 Mobile Printer User Manual ZQ110 Copyrights The copyrights in this manual and the label print engine described therein are owned by Zebra Technologies Corporation Unauthorized reproduction of this manual or the software in the label print engine may result in imprisonment of up to one year and fines of up to 10 000 17 U S C 506 Copyright violators may be subject to civil liability This product may contain ZPL ZPL 116 and ZebraLink programs Element Energy Equalizer amp Circuit E38 and AGFA fonts Software ZIH Corp All rights reserved worldwide ZebraLink and all product names and numbers are trademarks and Zebra the Zebra logo ZPL ZPL Il Element Energy Equalizer Circuit and E3 Circuit are registered trademarks of ZIH Corp Al

Download Pdf Manuals

image

Related Search

Related Contents

  マルチモノキュラー 4×12 取扱説明書  Manuale dell`utente - M  

Copyright © All rights reserved.
Failed to retrieve file