Printrex MP200 User Guide
Contents
1. PRINTREA TRANSACT Dimensions 152mm 6 H 406mm 16 W 305mm 12 D Weight 6 4kg 141b Power Requirements 100 240VAC 50 60Hz Data Interface IEEE 1284 Parallel Chart Speed 5 25 50 100mm sec Chart Resolution 8 dots mm Y axis 20 dots mm X axis at 5 25 and 50 mm sec 10 dots mm X axis at 100 mm sec Media Compatibility A Size 8 1 2 by 11 inch A4 Size 210 by 297 mm 1028 0044 R9 MP200 Technical Specifications Storage Temperature 20 C 4 F to 75 C 167 F Fuse 3 0 Amp 250V Slo Blo CAUTION For continued protection against risk of fire replace only with same type and rating fuse ATTENTION Utiliser un fusible de rechange de meme type Usage Class 1 No Applied Part Protection against harmful ingress of water ordinary Not suitable for use in the presence of flammable Anesthetics or oxygen Continuous mode of operation 8 of 10 Accessories and Supplies Please refer to the Instrument User Guide Service Manual for information on the available accessories and supplies for this Recorder www transact tech com USA United Kingdom Canada 1028 0044 R9 Contact Information TransAct Technologies Incorporated Ithaca Facility 20 Bomax Drive Ithaca NY 14850 USA TransAct Technologies World Gaming Headquarters amp Western Regional Repair Center 6700 Paradise Road Suite D Las Vegas NV 89119 USA Telephone 8772. PRINTREX MP200 by TRANSACT User Guide Table of Contents Preparation Operation Safety Troubleshooting Service Technical Specifications TRANSACT Technologies Incorporated 1028 0044 R9 1 of 10 www transact tech com PRINTREXA MP200 bY TRANSACT Preparation Front Panel Paper Compartment Access Hole Package Contents MP200 Chart Recorder Oe aa Door Power Cord K Parallel Interface Cable This User Guide Unpacking Locate and remove the Power Cord and Parallel Interface Ll Cable Paper Release Tab Remove the protective end caps and plastic bag The Recorder PAPE ewan can now be placed on the desired surface Note that there is a Figure 1 cardboard insert that holds the Writing Surface in place during shipment This insert should be removed now The packaging material is not required beyond this point Getting Familiar Review Figure 1 through Figure 3 to become familiar with Power Switch the names and locations of the various features of the Recorder These names are used throughout this O perators Guide Interface Connector Power Entry Module Figure 2 Door in Open Position Front Surface Figure 3 1028 0044 R9 2 of 10 www transact tech com PRINTREX MP200 bY TRANSACT Preparation Setting the Paper Size The Recorder is factory set for A size 8 1 2 by 11 inch media It is required to adjust the Recor
3. 7ithaca or 607 257 8901 Main fax 607 257 8922 Sales fax 607 257 3868 Technical Support fax 607 257 3911 Web site www transact tech com Western United States 877 822 8923 Fax 702 254 7796 United Kingdom 011 44 170 977 2500 Fax 011 44 170 977 2505 R Associates Inc 6610 Gant Road Houston Texas 77066 USA Telephone 713 973 1500 Fax 713 598 8311 Web site www t associates com AVNET Embedded 5a Waltham Park White Waltham Maidenhead Berkshire SL63TN Telephone 44 1628 518900 Web site www avnet embedded eu Kesh Downhole Measurements Inc PO Box 246 Clyde Alberta TOG OPO Canada Telephone 780 348 5278 Fax 780 348 5731 Email kevindm2 clearwave ca 9 of 10 www transact tech com Contact Information Germany Elkutec Electronic GmbH Postfach 11 33 D 85386 Eching bei Munchen Erfurter Strasse 31 Germany Telephone 49 89 31 90 91 0 Fax 49 89 31 90 91 91 Web site www elkutec de Email sales elkutec de China Star Luck Enterprises Inc Beijing Office Room 328 Grand Vision Business Building No 2 Jiuxiangiao Road Chaoyang District Beijing 100015 China Telephone 86 10 51305677 Fax 86 10 51305658 Singapore HABS Industries Pte Ltd 2 Kensington Park Drive 04 04 Singapore 557320 Telephone 65 967 32002 or 65 816 32322 Fax 65 234 3158 Email habsindustries gmail com 1028 0044 R9 10 of 10 www transact tech com
4. ata processing equipment and IEC 601 1 for Figure 5 medical equipment Furthermore all configurations shall comply with the system standard IEC 601 1 1 Everybody who connects additional equipment to the signal input part or signal output part configures a medical system and is therefore responsible that the system complies with the requirements of the system standard IEC 601 1 1 If in doubt consult the technical services department or your local representative Connecting the Power Cord Locate the Power Cord and insert the end that mates with the Recorder Power Entry Module Figure 2 Plug the other end of the Power Cord to the receptacle location described in the User Guide Service Manual of the Instrument the Recorder is connected to 1028 0044 R9 3 of 10 www transact tech com PRINTREX MP200 bY TRANSACT Preparation Loading Paper To load the paper first clear any paper from the previous supply by using the Paper Advance button or the Paper Release Tab Open the Paper Compartment D oor and place the new stack of paper in the Paper Compartment Note The orientation of the paper is such that the first sheet entering the Paper Entry Channel has the NON PRINTING side of the paper facing up AND the form marker small black rectangle towards the rear of the Recorder Position the leading edge of the paper into the Paper Entry Channel and manually feed the paper into the channel until it comes to a complete s
5. cleaning with the following cleaning agents Isopropyl alcohol Ammonia Chlorine bleach 1 10 concentration with water Hexachlorophene PhisoHex G lutaradehyde Cidex It is recommended that a soft cloth dampened with the cleaning agent be used to clean the surfaces of the Recorder Do NOT submerse or allow spills onto or in the product 1028 0044 R9 5 of 10 www transact tech com PRINTREX MP200 TRANSACT Safety Restriction on Use Use this equipment only for its intended use as described in this guide Do not use power supplied outside the specified voltage hertz range Do not block any openings on the equipment Do not use corrosive chemicals or vapors on the equipment Do not expose equipment to rain spills or moisture Grounding This equipment must be grounded Connect only to a properly grounded outlet Power Cord The power cord supplied with the equipment is a hospital grade power cord Do not operate the equipment if it has a damaged power cord or plug Do not immerse power cord or plug in water Do not usea power cord other than that supplied with the equipment serviceability There are no user serviceable parts inside the equipment Refer all service to a qualified service technician FCC Compliance This unit has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protectio
6. der for Paper Size Adjustment use with A4 size 210 by 297 mm media A Number Screws top 3 ea 1 Phillips screwdriver is recommended to make the adjustment The adjustment can be made by placing the Recorder on its Front Surface a cloth or towel can be used to protect the Recorder and table top from scratches Locate and loosen do NOT remove the five Paper size Adjustment screws see Figures 4 and 5 Slide the Paper Adjustment Plate inward towards the center of the Paper Compartment until it stops There are two holes in the Paper Adjustment Plate that can be used to maneuver the Paper Adjustment Plate into position Tighten the adjustment screws while holding the adjustment plate in position Paper Adjustment Plate Figure 4 The Recorder can be reset to accommodate A sized media by using the above procedure except sliding the Paper Adjustment Plate away from the Paper ETO E E E E Compartment then re tightening the adjustment ats 2 ea SCrews Connecting the Parallel Interface Cable Locate the Parallel Interface Cable and insert the end that mates with the Recorder Interface Connector Figure 2 Insert the other end of the Parallel Interface Cable to the Instrument Parallel Port Connector refer to the Instrument User G uide Service Manual to locate the Parallel Port Connector Accessories equipment connected to the analog and digital interfaces must be certified to the respective IEC standards i e IEC 950 for d
7. n against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Declaration of Conformity TransAct Model Printrex MODEL MP200 02 MEDICAL CHART RECORDER is declared to conform with the following standards RoHS Directive for IT and Telecommunications Equipment The Printrex MP200 02 shall be compliant with Directive 2011 65 EU of theEuropean Parliament and of the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment RoHS Directive 1028 0044 R9 6 of 10 www transact tech com PRINTREA TRANSACT Troubleshooting Y our chart recorder is designed and manufactured to provide consistent and reliable service However in the event of a problem consult the chart below SYMPTOM No power in unit No recorder output Cannot load paper Paper skews and Causes a paper jam POSSIBLE CAUSE 1 Power cord is not plugged into outlet 2 Power cord is not plugged into recorder power entry module 3 Power switch is in the OFF position 4 Outlet is no
8. remains on for approximately four seconds after there is no activity on the Paper Advance button The indicator illuminates briefly when power is applied as a test of the indicator itself 1028 0044 R9 4 of 10 www transact tech com PRINTREA MP200 TRANSACT Operation Power Indication The Power Indicator indicates that power is on and remains lit while power is on Error Indication The Error Indicator indicates an error condition with a series of long and short flashes The number of long flashes corresponds to the tens digit of the error code and the number of short flashes corresponds to the ones digit of the error code The following is a list of error codes with their description 11 Paper Empty 21 Under Voltage 22 Over Voltage 23 Under Temperature 24 Over Temperature 43 System Error Refer to the trouble shooting section on page 7 for appropriate action in the event of an error condition The Error Indicator illuminates briefly when power is first applied as a test of the indicator itself Clearing a Paper Jam In the event of a paper jam lift the Paper Release Tab and gently pull the remaining paper clear of the print head and platen Do NOT use any sharp objects or tools near the platen or print head or damage may result Care and Cleaning There is no regular cleaning required for proper operation of the Recorder however the Recorder surfaces are designed and manufactured to permit
9. t providing power 5 Power cord is defective 1 Power switch is off 2 Paper is out 3 Paper is jammed 4 Interface cable is unplugged 5 Interface cable is defective 1 Power switch Is off 2 Paper is not inserted far enough into recorder 1 Paper is mis aligned How to Obtain Service Refer to the User G uide Service Manual of the Instrument the Recorder is connected to for contact information regarding servicing this Recorder MP200 Troubleshooting WHAT TO DO 1 Verify power cord is firmly plugged into outlet 2 Verify power cord is securely connected to the recorder Power Entry Module 3 Verify the switch is in the correct position 4 Plug another device into the outlet to check for power 5 Plug another device onto power cord to check for power 1 Turn on power 2 Reload paper 3 Clear the paper jam 4 Check that the interface cable is securely attached at both ends 5 Try the interface cable on another working system 1 Turn on power 2 Gently hand feed paper into recorder Paper Entry Channel until it stops firmly against the platen approximately 3 inches then press Paper Advance button 1 Raise the Paper Release tab and align paper parallel to recorder Service The model and serial number of the Recorder is located on the rear of the unit Please have this information available when service is required 1028 0044 R9 7 of 10 www transact tech com
10. top approximately 3 inches Note Feeding the paper with one hand in the center of the paper yields best results Press and hold the Paper Advance button until the paper can be seen exiting the Paper Exit Path Close the Paper Compartment D oor while being sure the paper exiting the Paper Exit Path is on top of the Writing Surface The paper is now loaded Running Self Test Before operating the Recorder perform the self test by turning the power Switch to the On position while holding down the Paper Feed Button Release the Paper Feed Button after the self test begins The Recorder will perform various internal electronics tests as well as electromechanical tests The Recorder is ready to operate Operation Operation Use the Recorder for general charting and reporting There are no special controls or modes of operation to be set on the Recorder for normal operation Refer to the Instrument User G uide Service Manual for the various output options of the Recorder Feeding Paper A Paper Advance button is located on the Front Panel Press the Paper Advance button to advance the paper until the button is released or the paper advances to the Top of Form To continue advancing paper after the Top of Form is reached release and then re press the Paper Advance button Paper Empty Indication The Paper Empty Indicator shows that paper is not loaded and remains lit while paper is not loaded When loading paper the indicator
Download Pdf Manuals
Related Search