Shock Absorber Rebuild Manual
Contents
1. 605 01 039 Rev C Tools amp Materials Required for Rebuild 1 Fox Swt R3 Fluid 1 Qt Fox P N 803 11 006 2 Piston Band Installation Tool Fox P N 803 00 187 3 Fox IFP Depth Setting Tool Fox P N 803 00 294 4 Fox Seal Installation Bullet 5 8 Fox P N 398 00 094 A 5 DSC Socket Fox P N 398 00 294 6 RC3 Rebuild Kit Fox P N 803 00 184 7 Misc Allen Wrench Set 8 Mallet 9 Pin Spanner Tool 10 Screwdrivers 11 Torque wrench 12 9 16 Wrench 13 6mm Allen Hex Socket AQ i 605 01 039 Rev C REBUILD INSTRUCTIONS Important notes e SAFETIES FIRST Always wear safety glasses and read directions completely BEFORE disassembling the shock e Cleanliness is critical make sure your work area is clean and un cluttered prior to starting work Contamination of the shock will lead to premature wear and poor function of your shocks e IMPORTANT When replacing a seal during a service make sure that the new seal is the same size shape and material as the one you are replacing In some cases there may be two seals in the rebuild kit that look similar 1 Record the relative Preload indicator number as well as the Rebound Compression adjustment settings and Bottom out control 2 Using a 4mm Allen wrench loosen pinch bolt on preload ring and back the pre load adjuster off until the spring is loose on the body 3 Remove the wire retaining ring under the shaft eyelet end spring collar and remove spri2. RACING SHOX Shock Absorber Rebuild Manual Model PODIUM RC3 FOXRACINGSHOX 150 Hangar Way Watsonville CA 95076 PHONE 800 369 7469 FAX 831 768 7026 Email psservicemw ridefox com Website www ridefox com 605 01 039 Rev C 605 01 039 Rev C Disclaimer FOX Racing Shox is not responsible for any damages to you or others arising from riding transporting or other use of your FOX equipped vehicle In the event that your shock breaks or malfunctions FOX Racing Shox shall have no liability or obligation beyond the repair or replacement of your shock pursuant to the terms outlined in the Service and Warranty provisions of this manual Consumer Safety RIDING A MOTOR VEHICLE IS DANGEROUS AND CAN RESULT IN SERIOUS INJURY OR DEATH RIDE RESPONISBLITY AT ALL TIMES Maintain your vehicle and your suspension Always wear a helmet protective clothing and eye protection Ride within your limits Tread lightly Removal amp Installation The method for removing and installing your FOX Racing Shox is different for every vehicle Refer to your vehicle s service manual for complete instructions Recommended Service Intervals Your FOX Racing Shox will perform the best if serviced at regular intervals Every Ride Wash and dry your vehicle and suspension Every Ride Visually inspect shock Every 40 hours Change shock oil and seals ACTUAL SHOCK AND PARTS DEPICTED MAY VARY FROM MODEL YEAR TO MODEL YEAR RACING SHOX
3. Methods of Shipping FOX Racing Shox uses UPS Ground Service within the USA Customer may request UPS Air Service at an extra cost All non warranty shipping charges are the customer s responsibility 27 RACING SHOX
4. Using your fingertips depress the shaft bearing into the shock body to expose the wire retaining ring Remove retaining ring Use extreme caution not to scratch the bore of the body tube 605 01 039 Rev C 14 Remove the shaft assembly from the body tube and place on a clean lint free paper towel 15 Using the FOX DSC socket tool 398 00 267 remove DSC adjuster from body end cap assembly inspect the DSC for any wear or damage replace the o rings 605 01 039 Rev C 16 Lightly grease the o rings on the DSC reinstall and torque the DSC to 35 FT LBS Do not tighten using the 17mm High speed adjuster hex this will damage the DSC 17 Set body assembly aside on a clean lint free paper towel 18 Clamp the shaft eyelet securely in soft jaw vice with the piston end up 19 Using a 4mm hex key socket remove bottom out piston from end of shaft Ensure that the Rebound lock nut is tight 20 Using a 17mm socket remove the shaft lock nut 605 01 039 Rev C 21 Slide only the tip of Phillips Head Screwdriver into hole at end of shaft Hold the piston assembly under the top out plate and lift upwards Slide the piston assembly onto the shaft of the Screwdriver 22 Slide the bearing assembly and cap off the shaft 23 Remove bottom out bumper and spacers if any Inspect and replace if needed 10 605 01 039 Rev C 24 Remove all the seals and o rings from the bearing as
5. 05 01 039 Rev C 45 Dispose the excess oil in the reservoir a light film of residual oil left in the reservoir is ok 46 Lightly grease the o ring and Install the reservoir end cap and retaining ring 47 Charge the reservoir to 150 PSI of nitrogen Install the Schrader cap 20 605 01 039 Rev C 48 Clean any residual oil from the top of the bearing and lightly grease the threads of the bearing Install the bearing cap Tighten the set screw 49 Reinstall soring and hardware Set all the adjusters to your personal preference or factory setting 12 clicks out from fully closed position Congratulations You ve completed the servicing of your FOX Podium RC3 Carefully reinstall the shock on your motorcycle Always refer to your motor cycles owner s for proper torque specs for your shock mounting bolts DO NOT OVER TIGHTEN Be sure to RIDE SLOWLY in the beginning to ensure the shock and your vehicle s suspension is performing correctly Thanks again for choosing FOX Racing Shox 21 605 01 039 Rev C Contact Information FOX Racing Shox Phone 800 369 7469 130 Hangar Way North America 800 369 7469 Watsonville CA 95076 Fax 831 768 7026 E mail psservicemw ridefox com Website www ridefox com Business Hours Monday Friday 8 00AM 5 00PM Pacific Time Service Warranty 1 Contact FOX Racing Shox at 800 FOX SHOX 800 369 7469 to obtain a Return Authorization Number RAN and shippin
6. firmly this allows the valve shims to open and to let any air bleed out from the piston assembly Tap until the rebound bleed port is just submerged into the oil Allow a few minutes until all air bubbles have dissolved 39 Install the bearing assembly allowing oil to overflow from the bleed hole in the bearing Oil should rise to the top of the body around the o ring 17 605 01 039 Rev C 40 Set the Low Speed Compression adjuster to fully open position Press the bearing assembly into the body just past the retaining ring groove Do not push the bearing any further than shown in the image below 41 Install the retaining ring Push the IFP down using the IFP tool and at the same time pulling up on the shaft This ensures full extension on the shaft for next step 18 RACING SHOX 605 01 039 Rev C 42 Set the Low Speed Compression adjuster to fully closed position Remove the IFP bleed screw and set the IFP depth using the table below Please note that the IFP depth is application specific 2217 20 08 42001 2 88 gt 43 Measure your IFP depth as specified in the image below and set the correct depth Use a ruler and the IFP tool RESERVOIR LENGTH 005 APPLICATION SPECIFIC EE SHOCK SPECIFICATION SHEET IFP DEPTH 050 EE IFP DEPTH TABLE S S eL 7 7 J V RE LLLA DEG x trr 5 Lileks a _ D Er ooi 44 Install the IFP bleed screw RACING SHOX 19 6
7. g instructions 2 Satisfactory proof of purchase receipt is required for warranty consideration 3 Mark the Return Authorization Number RAN and the Return Address on the outside of the box Send the shock to FOX Racing Shox with the shipping pre paid by sender 4 Include a description of the problem vehicle information Manufacture year amp model type of FOX product spring rate type of riding and a return address with daytime phone number Warranty Policy FOX Racing Shox products are covered by a 1 Year Limited Warranty against defects in materials and or workmanship Any modifications to the product will void all warranty This Warranty will be extended to the original retail consumer of an OEM Customer s FOX Racing Shox equipped vehicle and is valid for one year from the original date of purchase from an OEM Customer s authorized dealer Warranty is limited to the repair or replacement of the FOX Racing Shox product FOX Racing Shox reserves the right of final decision with regards to all warranty related issues Warranty is void when damage to the shock has occurred from the following Abuse Seal damage due to power washing Damage to the exterior finish caused by debris rocks or crashes Any attempts to disassemble shock absorber Modifications Non factory oil use or improper service Shipping damage or loss purchase of full insurance is recommended Methods of Payment VISA MasterCard and or Cashier s Check
8. ion Fluid 803 11 006 Allow oil to level out between the body and the reservoir this may take a few minutes 33 Fully close the Compression adjuster Fill oil into the reservoir to 1 2 from the rim of the reservoir 14 RACING SHOX 605 01 039 Rev C 34 Cover the bleed hole in the IFP using your finger slowly submerge the IFP into the reservoir allowing some oil to overflow Remove the finger covering the bleed hole and submerge the IFP into the oil until the o ring seats This procedure prevents any air from being trapped under the IFP Install the IFP bleed screw using a new o ring 35 Fully open the Low Speed Compression adjuster Using the IFP Installation tool push the IFP to the bottom of the reservoir this will force the air trapped in the Compression adjuster out of the body Add oil into the body until half full Pull the IFP up approximately 2 and push down again Repeat this process until no air bubbles are visible in the shock body 15 605 01 039 Rev C 36 Pull the IFP to about 1 from the bottom and fully close your Low Speed Compression adjuster Add oil into the body to approximately 3 4 from the rim 37 Install the piston assembly into the body Ensure that the piston band does not extrude out of the piston gland while doing this 16 RACING SHOX 605 01 039 Rev C 38 Wrap a rag around the shaft and the body to prevent oil spill Strike the shaft assembly
9. ng collar parts 4 Clean the entire shock assembly with soapy water or mild solvent 5 Back the Rebound adjustment screw all the way out full soft Back the Low Speed Compression adjustment knob all the way out Cfull soft Back the B O C adjustment all the way out Cfull soft RACING SHOX 605 01 039 Rev C 6 Clamp the shock body eyelet securely in a vice with the shaft side up Be sure to use SOFT JAWS to prevent damage to the shock Alternately a clean towel can be used in the vice jaws to protect the shock 7 Using a 3 32 Hex Key loosen the bearing cap set screw do not take it all the way out Use a 3 16 pin spanner tool to unscrew the bearing cap slide the bearing cap up to the bottom out bumper 605 01 039 Rev C 8 Remove the Schrader valve cap with the 3 16 pin spanner from the end of the reservoir to expose Nitrogen Schrader valve 9 Depress the air valve core to release pressure Be careful as high pressure Nitrogen will escape as you purge the valve 10 Depress the blue reservoir end cap to expose the wire retaining ring Remove wire ring Use extreme caution not to scratch the bore of the reservoir tube 605 01 039 Rev C 1 Remove the reservoir end cap using the extraction tool Clean the end cap and replace the o ring 12 Remove the IFP bleed screw and remove the IFP using the extraction tool Replace IFP o ring and band Dispose the oil from the reservoir 13
10. sembly and cap Use extreme caution when removing seals from bearing assembly Do not scratch the sealing surfaces for the seals and o rings Doing so will compromise the performance of your shock Replace parts in order shown in the illustration below 25 Clamp shaft eyelet securely in soft jaw vice 26 Slide spacers Cif any and bottom out bumper onto the shaft 11 RACING SHOX 605 01 039 Rev C 27 Install the Bullet tool on the shaft and lubricate the shock shaft with assembly lube Slide the bearing cap and bearing assembly onto shaft 28 Separate the Compression and Rebound valve stacks Secure the order by using a zip tie and set aside Cut the piston band at a 45 degree angle to prevent any damage to the piston remove both band and o ring from the piston 12 605 01 039 Rev C 29 Install the new o ring and piston band using the FOX Piston Band Installation tool 803 00 187 Ensure that the band has seated correctly on the piston before proceeding 30 Install the Compression valve stack piston and Rebound stack onto the shaft 13 605 01 039 Rev C 31 Install the piston nut using a 17mm socket and torque to 18 FT LBS Install the bottom out piston using a 6mm hex key socket torque to 25 FT LBS Set the shaft assembly aside 32 Clamp the body in the vise Check that the Low Speed Compression adjuster is set to fully open position Fill the reservoir with Fox R2 Suspens
Download Pdf Manuals
Related Search