SC12 Operation Manual and Spare Parts List
Contents
1. IPC Eagle OPERATIONS MANUAL amp PARTS LIST SC12 Fastracts Extractor IPC Eagle 3650 Dodd Rd Eagan MN 55123 800 486 2775 www ipceagle com BEFORE OPERATING THE MACHINE Read the manual carefully and completely before attempting to operate the unit This manual has important information for the use and safe operation of the machine Keep this manual handy at all times This machine will ensure years of satisfactory service if operated and maintained according to recommendations in the manual If additional information is needed please contact your local distributor or write to IPC Eagle 3650 Dodd Rd Eagan MN 55123 All information and specifications printed in the manual and parts list are current at the time of printing however because of Eagle Power s policy of continual product improvement we reserve the right to make changes at any time without notice This machine is shipped with antifreeze in the solution line system to protect the pump and valves from freezing during transport and storage Before you use the unit rinse the solution line system with clean water See Preparing The Machine WARNING The machine was designed for use on carpet and upholstery extraction applications as per instructions and recommendations written in this manual Any deviation from its proper use or purpose and the conseguential damage that may occur is the sole responsibility of the end user Disconnect the power cord from ou2. HOSE HOSE DRAIN 5 8 OD x 1 8 WALL 90 ELBOW 1 2 MP x 3 8 BARB 90 ELBOW 1 2 MP x 5 8 BARB CLAMP HOSE 5 8 CLAMP HOSE 7 8 HOSE SOLUTION 3 8 ID DECAL KIT DECAL KIT SOLUTION TANK ASSEMBLY SOLUTION TANK MOUNTING KIT HOUSING MOTOR PLASTIC BRUSH DRIVE MOTOR ASSEMBLY 220V WIRE ASSEMBLY GROUND VACUUM MOTOR PULLEY BRUSH DRIVE MOTOR BELT TIMING COVER PLATE ASSEMBLY SPRING Part No D02391 D02359 E02431 D02373 1 D02372 D02372 80491 1A E03431 82407A J00618 L00767 F02465 7 F02465 6 A00165 80263 3A J00598 A00138 A00099 J00637 J00652 J00613 H02561 H02552 F02463 12 82310A F02470 G 82538 1A 00185 6A D00398 A L00779 1 82378A Qty c c lA c gt y Fig NO NO DN NO FP a Aa Aa o o o o NO Item 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 PARTS LIST FASTRACTS SC7 and SC12 Description BRUSH CHAMBER ASSEMBLY 90 ELBOW 1 8 FP x 1 4 C GLIDE BACK SS GLIDE FRONT SS SLIDE BLOCK ASSEMBLY WASHER SLIDE BLOCK 1 16 THK 25 64 ID 2 OD STRING GUARD ASSEMBLY BEARING BRUSH BRUSH SHAFT BRUSH STEEL 1 2 x 18 SLINGER ASSEMBLY ROTARY BRUSH PULLEY ROTARY BRUSH WASHER 3 32 THK 7 16 ID 5 8 OD 14 SPRAY TIP Brass 1 8 NPT COVER PLATE ASSEMBLY OPEN END COVER PLATE ASSEMBLY PULLEY E
3. and workmanship for a 3 year period Parts replaced or repaired are warranted for the remainder of the original warranty period 1 Year Subject to the conditions stated below EPP warrants all other cleaning equipment components to be free from defects in materials and workmanship for a 1 year period Parts replaced or repaired are warranted for the remainder of the original warranty period Batteries are prorated for one year EPP will furnish and charge for replacement parts including transportation to the original owner through an EPP authorized service center If the part is returned within 30 days and is found defective the owner will be credited for the cost of the replacement part including shipping and handling Labor charges are covered for one year from the date of purchase if provided by an authorized EPP service center Travel is covered for 90 days for battery operated equipment only Wear items exempt from warranty include belts carbon brushes power cords wheels pad drivers clutch plates brushes pads handle grips filters screens throttle cables and squeegees This warranty shall not apply to failures caused by misuse or abuse improper maintenance as stated in the operation manuals use of unauthorized repair parts repairs by other than an EPP authorized service center and damage in transit EPP disclaims and denies any liability for any direct indirect special incidental or consequential damage which may be su
4. 8 NPT 50 PSI BUSHING REDUCER 1 4 NPT 100 PSI 90 ELBOW 1 4 MP x 1 4 C 100 PSI TUBE FITTING BRASS 1 4 X1 4 C NUT HEX SHAFT ASSEMBLY HANDLE TUBE COPPER 1 4 OD LEFT TIPS TUBE COPPER 1 4 OD RIGHT TIPS TUBE COPPER 1 4 OD X 25 7 8 LG TUBE COPPER 1 4 OD X 16 9 16 LG SPACER 3 16 THK 1 2 ID 1 OD GASKET VACUUM MOTOR BRACKET BRUSH DRIVE MOTOR PUMP MOTOR INTERNAL BYPASS 1240VAC W MOLEX CONNECTOR 100 PSI LOWER FRAME ASSEMBLY ADAPTER 3 8 BARB x 1 4 FP 90 ELBOW 1 4 FP x 1 4 MP FILTER STRAINER IN LINE QUICK DISCONNECT 1 4 FP x 1 4 FP SWITCH GUARD ASSEMBLY COVER ROCKER SWITCH SWITCH LIGHTED ROCKER Part No 82291A F00463 00537A K00725 82355A C02310 82357A A00143 A00132 G02536 A00135 A00055 A00168 1 A00168 18 A00140 A00145 A00124 80418 6A A00085 5 A00085 4 A00085 7 A00085 6 C00240 E02448 D02370 02513F 100A 02341A A00061 A00052 K00709 A00102 82414A B00214 2 B02211 1 Qty 1 o c c l2 Fig o o ao eo No o O O o O O O O O O CO o 02 O O O PARTS LIST FASTRACTS SC7 and SC12 Item Description Part No Qty Fig 97 LIGHT INDICATOR GREEN LENS B021916 1 6 98 GRIP HANDLE BLACK K00715B 1 2 6 99 BOOT FLEX CIRCUIT BREAKER B02193 1 6 115v 1REO 100 SPRING BRACKET VACUUM VALVE ASSEMBLY 1 101 SPRING VACUUM VALVE SLIDE RETURN 2 102 HANDLE ADJUSTABLE D02403 1 6 103 SHAFT VACUUM V
5. ALVE D03356 1 104 CIRCUIT BREAKER 3A B02192 1 6 105 OUTLET ASSY ACCESSORY OPTIONAL 80188A 1 6 106 CORD WRAP ASSEMBLY 82408A 1 6 107 CORD ASSEMBLY HANDLE TO LOWER FRAME 00185 32A 1 6 108 GASKET HANDLE E03432 1 6 109 COVER PLATE ASSEMBLY 82409A 1 6 110 LOCK NUT 115VAC B00201 1 6 111 CORD POWER 115VAC B00221 2 1 6 112 SWITCH 10 AMP 250 FAC 1 6 113 STRAIN RELIEF POWER CORD 115VAC B02213 1 7 120 HARNESS RECTIFIER 00185 29A 1 2 121 RECTIFIER FISH PAPER ASSEMBLY B02171 1 2 163 RECTIFIER M00843 1 2 Fastracts SC12 HSV ANO 230V 50 60 HZ CARPET SPRAY WIRING DIAGRAM INDICATOR LIGHT SPRAY A Q BRUSH BRUSH TON G SWITCH MOTOR RED B L B HRR EG TOW LOWER FRAME L pr GREEN YELLOW LS we OLENOID F HITE BROWN PUMP MOTOR IPC Eagle Warranty Policy Limited Warranty Eagle Power Products EPP warrants new cleaning equipment against defects in material and workmanship under normal use and service to the original purchaser as detailed below 10 Years Subject to the conditions stated below EPP warrants polyethylene tanks and housings to be free from defects in materials and workmanship for a period of ten years 3 Years Subject to the conditions stated below EPP warrants all automatic scrubber components to be free from defects in materials
6. ND LABEL KIT ENGLISH PIVOT LID FRAME EXTENSION STEEL 1 SQUARE TUBE BRACKET ASSEMBLY HOSE GUIDE PIN ASSEMBLY RETAINING CLAMP ASSEMBLY CORD CAP END GASKET COOLING AIR DUCT HOSE EXHAUST 1 ID X 7 DUCT COOLING AIR STEEL FRAME UPPER STEEL FOOT RUBBER WHEEL ASSEMBLY BUSHING AXLE WHEEL MUFFLER ASSEMBLY CLIPS MUFFLER STEEL Part No 82362A A00144 D02366 D02365 80500A F00504 82235A G00536 F00505 D02371 82376A D00398 2 C02298 A00091 1 82368A 82367A D02344 1 D02344 82361A 82383A 80187A K00712 4 E02450 J00654 D02343 D02342 1 K00705 82514A K00674 D00418 14 80790A D02380 Qty NO NYO B PSY HM S S B S NY NYO Fig NN NN PN 1 5 6 Oo Ol Item 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 PARTS LIST FASTRACTS SC7 and SC12 Description VACUUM MOTOR MOUNTING ASSEMBLY 2 STAGE LOOM CORRUGATED 26 VACUUM MOTOR 2 STAGE 5 7 DIA 115V W MOLEX CONNECTOR CAP LATCH HANDLE LATCH HANDLE ASSEMBLY CAPSCREW MACHINE STEEL HEX HEAD 1 4 20 X 1 1 4 LG LATCH HANDLE SPRING ASSEMBLY TEE MALE BRANCH BRASS 1 8 MP x 1 4 C 90 ELBOW 1 8 MP x 1 4 C SOLENOID 1 8 NPT 115V BRANCH TEE MALE 1 8 NPT NIPPLE SHORT 1 8 NPT BUSHING REDUCER 3
7. ate grounded connectors Make sure the machine is connected to a grounded outlet having the same configuration as the grounded plug No adapter should be used with this machine Any modification to the connectors will void the warranty PREPARING THE MACHINE 1 Rinse then fill the recovery pail with clean hot tap water not to exceed 140 F When pouring water make sure drain hose is clipped in the upright position Pour the water into the solution tank 2 Add recommended amount of cleaning solution to the tank follow mixing directions on label for best results 3 Set the recovery pail back in place Add recommended amount of defoamer to the recovery pail Close the lid TO CLEAN CARPET 1 Connect machine to a grounded electrical outlet 2 Turn on the VACUUM PUMP and BRUSH switches 3 Lift up on the handle grips to insure that the front of the machine rests on the carpet Slowly pull the machine backwards while pressing on the carpet spray switch below the left handle grip Monitor the extraction process through the vacuum lid Release the spray switch 6 inches before ending the stroke NOTE If dirty solution does not appear through the vacuum lid check to be sure if The vacuum lid is resting properly on the recovery pails The machine s nose is touching the carpet in the working mode The solution tank is not empty 4 Roll the machine forward on its four wheels for next stroke Make overlapping passes to prevent strea
8. ffered as a result of sale delivery servicing use loss of any product downtime labor freight or other charges not expressly included herein Date Purchased Model Number Serial Number Please be sure to record this information This information will be necessary for future warranty claims IPC Eagle IPC Eagle Products Sales and Service Provided by 3650 Dodd Rd Eagan MN 551213 800 486 2775 651 686 5399 www ipceage com
9. from the ends of the brush shaft 3 Remove 4 screws from string guard Tap the shaft toward the right open end to remove the bearing 4 Remove 4 screws from slinger and pull off brush core Scrape off old sealant build up on the slinger and string guard It is advisable to replace the two bearings every time the brush is replaced 5 Reinstall the above component CAUTION Install shorter step on the shaft ends toward the left pulley side Apply silicon sealant such as GE Silicon auto seal onto the ends of the brush core before reassembling the slinger and string guard Fastracts SC12 353m e ABC DE SEE FIG 4 Fastracts SC12 VIEW ON BRUSH MOTOR HARNESS FOR TUV MODEL a Fig 5 NAU 8 4 3 JU 4 N E 292 na 2 R AN AEN p r Wij M 8 ims 5 by We x R ACK VIEW Fastracts SC12 FROM BRUSH MOTOR lt Fastracts SC12 Fig 6 47 O ON Oo o 12 13 14 15 16 17 18 19 21 22 23 24 26 27 28 29 30 PARTS LIST FASTRACTS SC7 and SC12 Description CLIP ADAPTER RETAINER HOSE ADAPTOR SEAL VACUUM INTAKE SHAFT LID PIVOT SPRING DOME PIVOT SPRING SLIDE BLOCK VACUUM LID ASSEMBLY GASKET VACUUM LID FILTER SCREEN ASSEMBLY VACUUM LID HOSE VACUUM 2 ID PLUG SOLUTION TANK RECOVERY PAIL RECOVERY PAIL DRAIN NOZZLE 1 2 BARB x 1 2 BARB CLIP ASSEMBLY DRAIN
10. i model Defective pump motor or rectifier POSSIBLE CAUSE 1 2 1 2 Loose pulley tension String caught between walls Defective bridge rectifier Defective motor Debris caught inside the slide block guide BRUSH DRIVE BELT SERVICE AND OR REPLACEMENT refer to parts diagram 1 Remove 2 1 4 20 hex screws attaching lower frame to upper frame 2 Remove 2 spring cover plate assemblies and carefully remove springs from the slide blocks 3 Loosen 2 1 4 20 hex screws that hold brush motor bracket in place Push bracket toward the front of the machine to loosen belt 4 Remove right Open End and left Pulley End cover plates 5 Slide brush assembly and slide blocks out from their guides Replace worn and defective belt 6 Reinstall above components Clean accumulated lint or debris inside the slide block guides and check for wear on the teflon surfaces Replace if necessary The slide block washer item 36 must be installed between the slide block guide and inside the divider wall Adjust belt tension by moving motor bracket toward the rear Apply minimum belt tension when the hex bolts are tightened to allow for a smooth vertical brush movement A belt too loose will cause the belt to skip when brush is applied on the carpet A belt too tight won t allow for 36 up and down movement 2222 REPLACEMENT OF BRUSH ASSEMBLY AND OR BEARINGS 1 Repeat steps 1 thru 4 2 Remove slide blocks
11. king Check solution level from time to time see solution indicator tube on rear left corner of the back NOTE If foam appears on vacuum lid turn the VACUUM SWITCH OFF IMMEDIATELY Add more defoamer to the recovery pails to dissolve foam or empty the recovery pails 5 When the solution tank runs empty turn off the vacuum pump and brush switches Empty the recovery pail and rinse thoroughly Then repeat steps on PREPARING THE MACHINE TO ATTACH ACCESSORY HOSE 1 Remove 2 hose adapter connection from machine 2 Attach 1 1 2 assembly with adapter plate to vacuum lid inlet 3 Pull back female guick disconnect sleeve on the machine and insert male plug on the solution hose Attach 1 1 2 assembly Remove 2 hose adapter TO EMPTY THE SOLUTION TANK 1 Unhook the drain nozzle located on the side of the machine from the drain clips placing the end of the hose into the recovery pail AFTER EACH USE e Empty and thoroughly rinse the recovery pail e Coil power cord onto the cord wrap e Remove dirt and lint build up inside vacuum lid filter screen e Clean solution line filter e Wash the vacuum lid with a soap solution and sponge to prevent dirt from accumulating on the surface To avoid scratching use soft cloth only e Lean the machine back on its 4 wheels during storage or when it s not in use to prevent brush distortion MAINTENANCE The upright extractor is engineered for minimum maintenance But it d
12. oes reguire some care to keep it in optimum working condition Careful attention to these maintenance instructions will give you maximum operating performance and life expectancy of the machine Solution line fittings and accessory tools Flush the machine and accessories at least once a month with solution of 1 part water to 3 parts white vinegar to neutralize the alkaline residue left by the cleaning solution Filter Solution screen Unscrew bowl and rinse screen in running tap water If screen is clogged up with soap soak in vinegar solution and brush clean e Vacuum lid screens Always keep the screen clean in order to maintain maximum suction and airflow performance from the vacuum motor The screens also prevent lint from accumulating in the vacuum motor fan chamber thus increasing the productive life of the motor Do not operate the unit without the screen installed If the screen gets lost or damaged replace it immediately Quick disconnect coupler Spray with lubricant WD 40 or equivalent to prevent coupler from sticking TROUBLESHOOTING ELECTRICAL SYSTEM PROBLEM POSSIBLE CAUSE No electrical power 1 Defective power cord 2 House or building circuit breaker trips Switch is turned on 1 Faulty electrical cable Power is imtermittent to motor 2 Defective Switches 3 Loose terminal or discolored terminal connections VACUUM SYSTEM PROBLEM POSSIBLE CAUSE No Vacuum 1 Vacuum lid is not resting on recovery pail 2 L
13. oose vacuum hose vacuum connection Low Vacuum 1 Accumulated dirt on lid screen 2 Worn out vacuum lid gasket 3 Lint amp dirt build up on suction head brush chamber 4 Defective vacuum hose 5 Loose connection in the vacuum motor SOLUTION SYSTEM PROBLEM Pump motor on no spray thru carpet spray tips or accessory tool Uneven or weak spray from tips Carpet spray is turned off solution still drips from spray tips Vacuum motor working pump motor fails to turn on ROTARY BRUSH SYSTEM PROBLEM Motor runs brush won t spin Brush motor fails to turn on after circuit breaker has been reset Floating brush won t move up and down POSSIBLE CAUSE BONO O oon WN Clogged spray tips Clogged solution intake filter screen Clogged solenoid valve or open solenoid coil If carpet spray works normally plugged up female quick disconnect coupler Punctured pump diaphragm Defective pump check valve Crack in pump housing Debris in check valve Clogged or dirty spray tips Accumulated dirt on solution intake filter screen Accumulation of debris inside pump and plumbing Worn pump bearing excessive noise Punctured pump diaphragm Defective rectified Debris caught in between the 3 solenoid valve parts andthe plunger Loose Molex plug connector Loose wiring connection Defective pressure switch in pump motor 100 ps
14. tlet before servicing Do not leave machine connected to an electrical outlet when unattended Do not immerse or use this machine in standing water Such use may cause electric shock This eguipment is not designed to handle or use combustible volatile substance such as gasoline or kerosene in on or near the machine The use of such materials will cause an extreme hazard condition When using an extension cord use only a 3 conductor grounding cord 12 ga wire or heavier To avoid electric shock do not expose the unit to rain store it indoors only Do not use the machine for dry vacuuming This machine is not outfitted with a fine dust filter and it will damage the vacuum motor s Use defoamer at all times to prevent damage to the vacuum motor s Do not use water in excess of 140 F 62 C Use only commercially available carpet cleaners and defoamer intended for use with machines of this type Do not use dyes bleaches ammonia or other additives The use of powdered cleaning solution if not diluted properly made result in damage to the pump Do not expose machine to freezing temperatures All repairs must be done by an authorized Eagle Power repair station Do not use replacement parts other than those specified in the parts list FAILURE TO COMPLY WITH THE ABOVE WARNING INSTRUCTIONS WILL VOID THE WARRANTY GROUNDING INSTRUCTIONS The 120 V A C and the 220 V A C models have been outfitted with the appropri
Download Pdf Manuals
Related Search